PRODUCTS. Where is the Best? AIR INDEX CYLINDER...MD MECHANICAL MULTIPOINT STOP UNIT...MSP MICRO-INDEX CYLINCER...MMD. Air Index Table...

Transcription

1

2 Air motive power PRODUCTS Stagehand of Smoothly Operating System Where is the Best? To express movement, a designer selects actuators. The actuators and peripheral equipment selected according to conventional and ordinary conception may be the products which have been widely used so far, therefore, common system will probably be made. However, to realize cost-down, saving space and high accuracy more than present, what method can be taken? When producing epochmaking system, is it proper to select actuators as usual? Even among actuators abundant in the world, there is something shining. Kamo Precision Industries, Ltd. is proceeding with development of such actuators, and because of keeping the concept, is supported by many fans, and tries to perform merchandise development. AIR INDEX CYLINDER...MD MECHANICAL MULTIPOINT STOP UNIT...MSP MICRO-INDEX CYLINCER...MMD Non-lubrication Air Index Table...MMD Non-lubrication

3 AIR INDEX CYLINDER By using a simple index mechanism, driving section by air, index mechanism section, positioning mechanism section are skillfully integrated. Powerful index torque developed Free of overrun due to sure index stop action Perfect locking at the time of stop No return error No accumulated error Free of main shaft free position and reversion by overload Possible to set index speed by air throttle valve and to conduct high speed index Actuation by one four-way valve No limit to rotation direction due to double axle type Possible to conduct differential index drive with small gear head (MICRO MINIDEX) Specification for type with sensor available, possible to realize reduction of manpower of design, installation and maintenance CONTENTS MIMIDEX... Internal Structure... 3 Operation Principle and How to Use Overall Dimension and Performance... 4 Note for Handling... 5 Allowable Load and Index Time Model Indication Note before Using... Specification for Type with Sensor... 3 Indication of Specification for Type with Sensor

4 Internal Structure MINIDEX consists of very simple elements as said Simple is the best. This means superior durability and fewer failures, and also shows good maintainability and safety. The figure below shows the locking state by positioning. Right chamber is pressurized and left chamber is exhausted. Shaft Main shaft with same size at both end 4 Hole Cape Has positioning hole. 5 3 Cam Piston Converts reciprocating motion into rotational motion. 6 Follower Cap Tube Locating Pin Operation Principle and How to Use Has cam follower section. Applied honing plating to inner surface. Performs positioning and kelly action. Note : MD-0, 30 differ partially from the above figure in structure. In MINIDEX, One () index is completed by () reciprocating. That is, indexing is conducted when the piston shown in the figure below moves right, and locking by positioning is conducted when it moves left. Fig. Stop ( Original Position ) Fig. Indexing Fig. 3 Locking Hole Cap Locating Pin Piston Shaft Fig. shows the locking state by positioning. Piston is pushed to left. Locating pin is fitted into the hole cap, and shaft is surely locked. How to Use There is no limit to installation direction. Flanged Dislocation Fig. shows the state that by switching valve, piston moved right,and indexing was completed. In this state, indexing is completed by 95% and locking is made once. At this time, a little dislocation between the center of locating pin and that of positioning hole is established. Operation Strictly, MINIDEX performs index action by double motion. As shown in right figure, movement by approximately 5 is required to conduct locking. It is necessary to take this into consideration. The torque at locking is always larger than that at indexing. Final index angle Locking angle Fig. 3 shows the original position again. When entering into hole, locating pin enters while performing indexing of the rest 5% and locking is made again. Installation hole Indexing angle When positioning, locking is made after moving by approximately 5 Direct Installation How to Conduct Piping Piping for index should be conducted to direction of two band wires on the body. (for only MD50 and 75) Rotation direction is clearly shown on the main body. MINIDEX Index port is at the side of two band wires. (only MD50, 75) Index side Lock side Lock Index Switching valve Max operating pressure Less than 0.7Mpa 3

5 Outside Dimension and Performance The following 4 types of MINIDEX are available. Torque property and the number of indexes should be taken into consideration when selecting. Torque should be set within 60% of theoretical value. Change of shaft shape, the specification for hydraulic type and for waterproof type can be dealt with. < Specifications for all models are for non lubrication type.> Rotation direction Reference mark Keyway 3x.8deep x6 long Rotation direction mark MODEL MD0-4-M4 x0deep (Opposite face is same.) Index Torque Index Accuracy ± minutes Number of Indexes, 3, 4, 6, 8 Recommended Index Time: Longer than 0.5 sec Index time varies according to load. Internal Capacity 3 0 cm Weight 500 g Air Pressure Rotation direction Reference mark Keyway 3x.8 deep x6 long MODEL MD30-4-M5 x deep (Opposite face is same.) Index Torque Index Accuracy ±8 minutes Number of Indexes,3,4,5,6,8,0, Recommended Index Time: Longer than 0.5 sec Index time varies according to load. Internal Capacity 3 8 cm Weight 800 g Air Pressure Rotation direction Reference mark Keyway 4x.5 deep x 5 long MODEL MD50-6-M6 x 3 deep (Opposite face is same.) Index Torque Index Accuracy ±6 minutes Number of Indexes,3,4,5,6,8,0, Recommended Index Time: Longer than.0 sec Index time varies according to load. Internal Capacity 3 50 cm Weight 4.5 kg Air Pressure Rotation direction Reference mark Keyway 5x3 deep x 40 long MODEL MD75-6-M8 x5 deep (Opposite face is same.) ( ) dimension is in case of 5 indexes or greater Index Torque Index Accuracy ±4 minutes Number of Indexes,3,4,5,6,8,0, Recommended Index Time: Longer than.5 sec Index time varies according to load. Internal Capacity 3 0 cm Weight kg (0kg) Air Pressure Dimensions and configurations may be changed without notice due to improvement. 4

6 Note for Handling.Since MINIDEX is small, even if production accuracy is retained within ±0.0, angle error becomes ±8 (in the case of MD-30.) Index accuracy more than it cannot be insured. Therefore, it is not recommended to design so as to obtain index accuracy in second directly from the shaft. In this case, the way to insert positioning pin into driven unit should be adopted..mechanically, MINIDEX moves almost uniformly. Therefore, applying excessive load or high-speed operation with large load is not recommended. In designing, try to extremely minimize GD (inertia). 3.Products complied with the standard are used for inner seals. Abrasion or damage of the seals may cause air leakage and result in output descent. For exchange of seals, contact us. 4.Installation altitude is free from limit, however, the way of use that load is applied to shaft (thrust) is not recommended. Thrust load should be received outside by thrust bearing. 5.See Instruction Manual for Safety and Handling before using. Allowable Load and Index Time. Allowable Load Model MD-0 MD-30 MD-50 MD-75 -If GD exceeds even if torque is within allowance, nonconformity may occur. shaft end Radial N(kgf) 4.7 (.5) 9.4 (3.0) 98.0(0.0) 96 (0.0) Thrust N(kgf) 9.8 (.0) 4.5 (.5) 58.8 (6.0) 98.0(0.0) These values are static load at the time of stop, not rotation allowable load.. GD (Flywheel Effect) This is not the moment of inertia. Model MD-0 MD-30 MD-50 MD Index Time Index time should be calculated from GD of load by the following equation. Load GD (3 - t) Index Time = t AllowableMax. GD (Example) In the case of Model MD50, GD of load = 800kgf- cm, index time is ; 800 (3 - ) =.6 second 000 Allowable Gd Unit:kgf-cm Model MD-0 MD-30 MD-50 MD-75 For documents of specification for type with sensor, refer to Page 3. (Reference) GD in the case of disc GD = WD W = Disc weight in kg D = Disc Diameter in cm Time required for one () index ( time for internal piston reciprocating ) is shown. Time required to switch valve is not included. By using the above figures as measure, and according to impact degree at the time of stop, fine adjustment of speed should be performed by speed control ( meter-out ). t Model Indication When ordering, enter as follows. MD Model Number of Indexes MD50 - < Example > < Model : MD50 Index : > 5

7 Mechanical Multipoint Stop Unit [MULTISTOPPER] is epoch-making product that make it possible for various feed equipment to perform intermediate multipoint stop. In feeding of slide table by air cylinder, for instance, stopping can be made at only two points; forward and backward end of cylinder. In the case where the table is required to be stopped accurately at midposition, the way to set movable stopper is adopted in many cases. However, in the case where many points, such as 4 or 5 points, mechanism and control become complex. MULTISTOPPER is useful in such a case. CONTENTS MULTISTOPPER... 6 What is MULTISTOPPER?... 7 Application Examples Overall Dimension... 8 In Working out Peripheral Design Electric Control... 9 Note for Installing Model Indication Note before Using... Specification for Type with Sensor... 3 Indication of Specification for Type with Sensor 6

8 What is MULTISTOPPER? MULTISTOPPER, being application product of small pneumatic intermittent cylinder MINIDEX made by us, is provided with the turntable on which many stopper pins are mounted on the end face of the disc, intermittently turns the disc each time when slide jigs make reciprocating, switches to stopper pins different in length and applies them to slide jigs, and make stopping and positioning mechanically at many points. The figure below shows an example of application ; the equipment to distribute to different 6 points by catching works supplied in turn to given place by parts feeder ( or conveyer ). Stopping can be made mechanically and accurately without using expensive pulse motor or servo system. Dealing with preparation of works of different types can be simply made by changing each disc or pins (Special Specification). Rotation control of main body can be conducted by only four way valve, and pipes are sufficient for piping. Follow to the figure below. Air cylinder Vertical Cylinder Finger Unit Stopper Disc Stopper Pin ~ 6 Set Point Original Position How to conduct piping Specification is for non-lubrication type. Piping for indexing at stopper disc side should be performed. Index port is at stopper disc side. Max operating pressure 0.7MPa or under MULTISTOPPER Lock Index Switching valve Application Example There are many successful applications of MULTISTOPPER. The photographs below show examples of application. Another application is that general purpose spot welding machine, which is provided with MINIDEX equipped with reduction gear on the shaft, mounted with 4 stopper pins on disc and installed as XY moving jig, is used as special purpose machine capable of applying spot welding continuously to more than 50 point. ( Right photograph ) Application Example Multipoint Spot Welding Machine Multipoint Fastening Equipment Multipoint Special Purpose Drilling Machine Multipoint Soldering Equipment Magazine Feeding Table Multipoint P & P Equipment ( Above figure ) Bar Cutting Equipment Work Multiple Distribution Escapement Many others 0 Point Slide Table 6 x 6 Point X Y Table 4 x 4 Point X Y Equipment ( During assembling ) 7

9 Overall Dimension Flanged Type F Piping port Rocking side Indexing side In the case where dimensions are not indicated, refer to MINIDEX. Intermittent rotating section Piping Port Pitch circle of stopper pin installation screw Installation hole L Pitch Installation hole 4-K Additional tap processing available M6, M8 J rear shaft Rotation direction ( Number of divisions ) N (Sorting in to be conducted at this point reference ) Symbol Model MSP30 - F MSP50 - F A B C D E F G H I J K L M P S T d N Weight (kg) M8 x M0 6.7 x9 Flanged Type S Installation hole 4-U Denotes figures from to. Dimensions not indicated here are same as F type. In the case where the number of divisions are more than 0, pin Rotation direction mounting screw N is ; M6 for MSP30, M8 for MSP50. J denotes key way. Symbol Model MSP30 - S MSP50 - S A B C D E F G H I J K L R S U N Q H8 0H Weight (kg) M8 x3 4.5 M0 x In Working out Peripheral Design. Manufacture stopper pin almost as per the figure below/. Make sure to set spanner latch, etc to be easily able to adjust length. Since tip impacts against counter-reinforcing plate, make sure to perform hardening. Hexagon Head Adjustment length Spanner latch Hole Hardening - Don t use pins being too long. -. Reinforcing plate to stopper pin should be designed so as to avoid interference with adjacent pins. While stopper is rotating, back reciprocating slide jig once to the original position so that stopper pins can rotate without interference. Clearance Slider Clearance 8

10 3. In setting pin length, determine from thrust load with reference to the figure below. ( Pin material is set to that equivalent to S45C. ) 00 Thrust Load S (kgf) MSP30 (M8) MSP50 (M0) L (mm) S kgf Stopper Pin Length (mm) Electric Control.Control of MULTISTOPPER itself is performed by the limit switch to turn the four way valve and the valve to ON/OFF or by the O timer. In the case of division into 4, for instance, when the valve is turned to ON, it stops after rotating approximately 85. Therefore, the signal is necessary at that point, and when the valve is turned to OFF by this signal, it is locked after rotating O O remaining 5. Moreover, the original position signal is obtained at the point of a total of 90 ( index ), which is used as forward signal for table, etc. Two each of LS are necessary. ( In the case of timer control, LS is not required, or l each is required at original position. ).For verification of contact of stopper pin and reinforcing plate, the figure below shows one of methods having been performed for reference. Hollow reinforcing plate Lead wire Stopper pin Reinforcing plate LS, etc Small proximity SW 3.If verification of contact mentioned above is performed, it is not objectionable to omit verification of position of each stopper. However, if necessary, detection by setting multiple dog in near shaft should be performed. In the case of division into 8, for instance, signals at each position can be found by combination of 3 or 4 each of LS. ( More than 0 signals were obtained by O combination of 5 each of LS in the example shown in the photo of previous item. ) Since lock angle is 5 being small, small sensors should be used. L S L S L S 3 Note : Another each of LS is necessary for the original position of stopper. Position In the case of high speed movement by air cylinder, shock is generated at stop end. In this case, it is preferable to hollow the reinforcing plate, set a shaft and install a small shock absorber in its back. Note for Installing. Install stopper pins and reinforcing plate so that lean is not generated at the time of impacting. If torque is generated on stopper disc at the time of impacting, the main body may be damaged.. When stopper pins are mounted and locked, pay attention not to apply torque to the disc. Make sure to fix the disc by vice, etc, or insert a bar into the detent hole around the periphery of the disc, and fasten the lock nut. ( Care should be taken strictly when assembling. ) 3. Thrust load is supported by metal bearing. Oil sometimes. 4. Try to rotate as slowly as possible so as not to generate impact at the time of indexing and locking. Model Indication When ordering, enter as follows. MSP Model Number of Indexes Installation Model <Example> MSP30-6S < Model : MSP30 with angle rest Index : 6 > 9

11 MICRO-INDEX CYLINDER By only switching of pneumatic valve, micro circle dividing ( 0.3 interval, division into 00 ) can be surly made. This pneumatic actuator is the product which non-backlash reduction gear Ball Reduction Gear and MINIDEX made by us are combined with, and is designed to enable to surly perform micro circle dividing by only switching of pneumatic valve. In spite of air equipment, this can perform micro angle index of 0.3 interval ( division into 00 ), so nothing can be compared with this. This can be called unique pneumatic equipment, and makes it possible to further expand the field of precision control by pneumatic. CONTENTS MICROMINIINDEX... 0 Overall Dimension... Specification and Property... Model Indication Note before Using Specification for Type with Sensor... 3 Indication of Specification for Type with Sensor 0

12 Overall Dimension - MMD8530S,0050S,75S - Piping port RC-V Type Symbol MMD8530S 60 MMD0050S 355 MMD575S A B C D d E F G H I J K K L M N O P Q R S T V x 5 0 x x 34 3 x x x MMD85305 is the combination of Ball Reduction Gear BR85S and MINIDEX MD30. MMD0050S is the combination of Ball Reduction Gear BR00S and MINIDEX MD50. MMD575S is the combination of Ball Reduction Gear BR5S and MINIDEX MD75. - For detailed dimensions, see each catalog. - M5 x0 M6 x M8 x MMD8530U,0050U,75U - Rotating section Piping port RC-V Symbol Type A B C D d E F G H I J K L M N O P Q R S T U V 3 x M5 MMD8530U x x MMD0050U x 05 MMD575U MMD8530U is the combination of Ball Reduction Gear BR85U and MINIDEX MD30. MMD0050U is the combination of Ball Reduction Gear BR00U and MINIDEX MD50. MMD575U is the combination of Ball Reduction Gear BR5U and MINIDEX MD For detailed dimensions, see each catalog. - M5 x0 M6 x M5 x M6 x5 M8 x

13 Specification and Property Model MMD 8530 MMD 0050 MMD 575 Special Model Item Number of Indexes 0,30,40,60,80,90,0,60, 80,40,360,~ 840 0,30,40,60,80,90,0,60, 80,40,30,360,480,~960 0,30,40,60,80,90,00,0, 50,60,80,00,40,300,360, 400,600,800,~00 Max Min Operating Pressure Pressure 0.7 (7) 0.7 (7) 0.7 (7) 0. () 0. () 0. () Output Torque 9.8 (00) 9.8 (00) 39. (400) Index Speed 0.5~.0~.5~ Products of intervals of 0.5 or index available MPa MPa N.m Products more than these indexes available (kgf/cm ) (kgf/cm ) (kgf.cm) Second Index Accuracy Angle Portion Repeat Accuracy Angle Portion Thrust Load 96 (0) 490 (50) 784 (80) N (kgf) Radial Load 94 (30) 490 (50) 784 (80) N (kgf) Output torque is the value in the case where air pressure is 0.5Mpa, and is the upper limit of load torque. Specification is for the non-lubrication type. Weight.5 7 4(6) Kg Model Indication When ordering, enter as follows. MICROINDEX MMD Model Output Form Number of Indexes Rotation Direction S U Right or left from output shaft <Example> MMD8530S-80R ( Type : Combination of BR85S and MD30, Right turn Index : 80) R L Note before Using Don t touch rotating section during operation to prevent dangerous accident. Work out design so that immediate stoppage and shutting off power and air should be conducted in case of emergency. Make sure to verify power and pressure off before installing and removing the product. Use operating pressure under 0.7MPa ( 7kgf/cm ). <For Driving Source> Fluid to be used should be air. In the case of using other fluid, contact us. Clean air should be used to drive MINIDEX, and air filter should be installed near MINIDEX or the valve to remove drain and dust. Drain ejection for air filter should be periodically performed. <For Piping> Before piping for MINIDEX, flushing in the pipe should be sufficiently performed without fail. If dust or sealant created during piping are contaminated, operation failure due to packing damage, etc may occur. <For Lubrication> It is possible to use without lubrication. However, in the case of using at normal full speed, turbine oil equivalent to no. 90 should be used. Spindle oil or machine oil are prohibited. <For Atmosphere> In the case of using at the location where water or oil dropping are splashed or at dusty location, protection with cover, etc is required. See Instruction for Safety and Handling before using without fail.

14 Specification for Type with Sensor Sensor is for verification at index and lock position. Use to verify valve switching and index completion (lock). In the case where non-sensor type is changed to the type with sensor, internal parts are partially different. In the case where it is required to change non-sensor type to the type with sensor, contact us. For details on the way to connect the type with sensor, perform connection after referring to attached instruction manual for sensor. Sensor Position Reference Mark Rotation Direction Specification for Type with Sensor Band Wire (only MD50,75) Model MD-0 MD-30 MD-50 MD A (74) B (79) ( ) dimensions are for the case of more than 5 indexes. Category Operation Form Control Output Rated Supply Voltage Rated Consumption Current Operating Ambient Temperature Operating Ambient Humidity Others Output Circuit Diagram Built-In Amplifier Type Proximity Switch ( Sealed Type ), Three Wire System N.O/N.C Output NPN Open Connector Max 00mA ( Less than 40V ) Residual Voltage Less than V Ripple 3mA or under 0-0~+70 C 35~95%RH with m long wire DC~4V Proximity Switch Main Circuit Load Control output (NO) Control output (NC) Load 0V Connection Diagram Red DC~4V White or Brown Load Black 0V Indication of Specification for Type with Sensor <Two each of sensor are attached.> MINIDEX M D Z MICROMINIDEX MMD Z 3

15 AIR INDEX TABLE Universal unit combining high rigidity and accuracy and covering wide application range This small index table, basing on the index principle of MINIDEX made by us, is a index table unit of which index accuracy and rigidity are improved. Since indexing is conducted by only air piping from 4 way valve, it is easy to install in small drilling machine or tapping, and labor saving can be achieved. By effectively utilizing small size property, installation in assembling machine can be performed. This unit has very wide application range. CONTENTS MINITABLE... 4 Internal Structure and Name of Parts... 5 Specification Table Air Pressure and Index Torque Overall Dimension... 6 How to Use and Note for Handling... 7 Index Time Model Indication 4

16 Internal Structure and Part Name Rotating Table Tube 3 Follower Cap 4 Hole Cap 5 Piston 6 Index Plate 7 Bell Cam 8 Locate Pin 9 Thrust Bearing 0 Ball Bearing One-Way Clutch Shaft All seal parts conform to JIS ( Japan Industrial Standards ). 9 Thrust Bearing and One-Way Clutch are not included in Model MT70. Specification Table Model MT70 MT00 MT5 MT00 Remarks Number of Indexed,3,4,6,3,4,5,6,8,3,4,5,6,8,0, 3,4,5,6,8,0,, 6 6 is semi-standard part. Index Speed 0.5 second~ 0.8 second~.0 second~.5 second~ Index Accuracy Loading Weight Max Operating Pressure Index Torque Internal Volume Basic Machine Weight Sub-Table Diameter Rotation Direction Locking Torque Allowable GD Operation Load! Thrust Radial + 4minutes + 3minutes + minutes + minutes Max kg Max 3kg Max 5kg Max 35kg 0.7Mpa (7kgf/cm ) 0.7Mpa (7kgf/cm ) 0.7Mpa (7kgf/cm ) 0.7Mpa (7kgf/cm ).96Nm (0.kgf-m).7Nm (.kgf-m) 9.4Nm (3kgf-m) 98Nm (0kgf-m) cm 50cm 500cm 300cm kgs 5ksg 0kgs 30kgs Max. 0 Max. 80 Max. 50 Max. 400 R.L R.L R.L R.L.9Nm (0.3kgf-m).7Nm (.kgf-m) 9.4Nm (3kgf-m) 98Nm (0kgf-m) 75kgf.cm 500kgf.cm 5000kgf.cm 30000kgf.cm 98N(0kgf) 980N(00kgf) 940N(300kgf) 4900N(500kgf) 9N(3kgf) 45N(5kgf) 490N(50kgf) 960N(00kgf) Speed control adjustment ( Value is for non-load. ) High speed prohibited in the case of max weight Same pressure of hydraulics permitted Division into 4, Air pressure is 0.4Mpa. Recommended diameter Direction from rotating table surface Air pressure is 0.4Mpa. Outer load at table stopping In the case of transverse installation, loading weight and operation load must be half of the value indicated on the above table. Air Pressure and Index Torque Index torque increases in proportion to air pressure, however, load torque should be used within the following range in consideration of internal part strength. ( In the case where the number of indexed is, it is approximately 60% of index torque. ) Index Rotation Torque Division into 3 Index Rotation Torque Division into 3~5 Index Rotation Torque Division into 3~4 Index Rotation Torque Division into 3~4 Operation Area Operation Area Operation Area Operation Area Air Pressure Air Pressure Air Pressure Air Pressure MT70 MT00 MT5 MT00 5

17 Outside Dimension and Performance Standard Type As for rotation direction, clockwise direction is right (R) as observed from the table surface. The figure below shows left (L). Design should be worked out by considering the installation hole positions of the following figure as the stat position. Reference indication mark Index port Positioning port Note M-4 slot O Note : In the case of MT00, the angle is 30. Model MT 70S MT00S MT5S MT00S A B C D E F G H I J K L M N O P M 5x 8 6 x0 O M5x6deep M 6x0 6.5 x0 O M 6x0 RC M 6x0 9 x3 O M 6x RC M0x0 x0 O M0x5 RC Flanged Type (Built-In Type) Compact equipment can be designed due to built-in type. It is possible to perform built-in to the panel of which shaft is level. Reference indication mark Index port Positioning port Note O Note : In the case of MT00, the angle is 30. Model MT 70S MT00S MT5S MT00S A B C D E F G H I J K L M N O P M 5x M M 6x0 6.5 M 6x0 RC M 6x0 9 M 6x RC M0x0 x6 O M0x5 RC S

18 How to Use and Note for Handling Four-way or five-way valve ( single or double deflection, or hand valve ) should be used. Air port at rotating table side (upper side) is for indexing, and that at lower side for locking. Indexing is performed by supplying air alternately to two air ports. (One reciprocating of internal piston shows index.) When air is supplied to index side, stopping is made at 5-7 shorter than required index angle. Then, when air is supplied to lock side, locking is made while rotating remaining 5 7. Trial run should be started at lower speed (speed control at lower side should be throttled. ), then speed should be increased gradually. If it is started at high speed first, internal cam may be damaged. Due to uniform rotation, in the case of high speed, impact is generated at stop end. If speed is increased gradually by above-mentioned method and the table is free of shake, operation can be conducted almost in safety. However, it is required to use as slowly as possible within given cycle. How to conduct piping Specification is for non-lubrication type. In the case of built-in to automatic machine, control is made by timer or limit switch. LS dog should be set at shaft end at lower portion of the table or table side. In the case of transverse installation (shaft is level.), load balanced right and left against the center of rotation should be applied surely. In the case of single load of arm, etc, advance run to rotation direction or damage of anti-reverse clutch may occur. In the case of transverse installation, loading weight is reduced by half. The main causes of failure are damage of cam by overload and cutting of parallel pin. In this case, operation is impossible. If you give us information on the state, we immediately take a necessary action. Sub-table should be made to be smaller in diameter and lighter in weight. ( Aluminum, etc ) See attached Instruction Manual for safety and Handling before using. MINITABLE Meter out is used for speed control. SOL Lock Indexing Switching valve Max operating pressure 0.7MPa Completion of indexing Final index Angle Index Angle Lock angle Start Detection by TM or LS Index Time Index time should be calculated from GD of load by the following equation. LoadGD (3 - t) Index time = t + AllowableMax.GD <Example> In the case of table diameter D = 0cm, weight W = 5kgf, GD is ; GD = WD = x 5 x 0 = 000kg.cm Index time is ; 000 (3 - ) = =.4 sec Accordingly, MT5 is selected from the specification table. Model MT 70 MT00 MT5 MT00 T Note: Time required for index ( time for internal piston reciprocating ) is shown. Time required to switch valve is not included. By using the above figures as measure, and according to impact degree at the time of stop, adjustment of speed should be performed by speed control ( meter-out ). Model Indication When ordering, enter as follows. MT Size ( 70, 00, 5, 00) Installation Model (S, F) Number of Indexes Rotation Direction(R,L) 7

19 And more See [Instruction Manual for Safety and Handling] attached with merchandise before using, and use correctly. Instruction manual must be carefully kept. For anything unclear, contact us. Note for safety Maintenance and Check Warranty Don't touch rotating section during operation to prevent dangerous accident. It is required to work out design stressed on safety like that air or power is immediately shut off in the case of emergency. Make sure to verify power and pressure off before installation and removal. Operating pressure should be less than 0.7Mpa ( 7 kgf/cm ) Make sure to verify all controls before operation. In air piping, see the instructions carefully for correct piping. Damage, abnormal stress and insertion to pipe should be avoided. Speed control must be surely piped near the main body with meter-out. Make sure to perform flashing in pipes before piping. Don't apply load more than allowance. In installing load, make sure to verify that the key shaft is free from rattle, and to thrust by set bolts. Corrective Action for Trouble In the case where power goes off or dangerous situation is expected, make sure to turn circuit power to off. It should be noted that stoppage is not conducted immediately even if emergency stop is made. Be away from the machine when re-operating. In the case where troubles are caused by overload or impact, contact us. Maintenance and Check Safety storage method should be taken. Following locations are not suitable for storage of machine or accessories not in use. Location where ;Children can reach to or carry out easily, temperature or humidity change suddenly, humidity is high, volatile matter is stored. Disassembly, modification, etc should not be performed. When installing and removing, make sure to shut off air to exhaust residual pressure before operating. Although parts complied with the standard are used for internal seals, abrasion or damage of seals cause air leakage and result in output decline. To prevent secondary accident by failure, it is recommended to replace in almost 5 years, even if they are used in ordinary circumstance. Warranty Period and Contents The period for repair without payment is provided as year from the date of shipment or 500 hours in operating conditions whichever short, subject to use in conditions specified by us. If failure or deficiency is caused clearly by poor quality of merchandise within warranty period, corrective action is taken free of charge. However, manhour and expenses for installation in and removal from actual machine are excluded from our charge. Merchandise disassembled or modified by customers cannot be repaired without payment. Maintenance and technical support in abroad are not available. If storage has continued for a long period, contact the shop of your purchase or us. How to Request Repair For nonconformity or repair, contact the shop of your purchase or our service department. SOS sheets are available in our service department. Make use of them for early solution of problems. Service Department Kamo Precision Industries, Ltd. Tel : Fax :

20 The description of this catalog is as of August 000. Specification, dimension, etc shown on this catalog are subject to be changed without notice for modification. The color of merchandise may differ from the original due to printing. Samples for evaluation are possible to be lent. Feel free to contact us for technical arrangement. Your visit to our company shall always be welcomed. Call us before coming. We hope that this catalog is useful to you. KAMO PRECISION INDUSTRIES, LTD. HEAD OFFICE : 66 Mitsukuri, Fujioka-cho, Nishikamo-gun, Aichi Pref JAPAN TEL: (Sales Department) (Engineering Department) (Service Department) FAX: (Sales/Engineering Department) (Service Department) URL: market@kamo.co.jp No E