TEL FA X W W W.ROAMER.CH

Transcription

1 ROMER OF SWITZERLND G GIELINSTR SSE 27 P.O. OX H-4503 SOLOTHURN TEL F X W W W.ROMER.H INSTRUTION MNUL INTERNTIONL WRR NT Y

2 !"!'%.!')%&#&' )%*!++ (,')-) "$/,# #,&'%)%&#&' Table of contents General information...5 Functional overview...6 How to change mode...7 Model overview...8 Synchronizing hands...10 Low battery Water resistance...12 acklight...12 Settings...13 Time Date...15 Time larm...18 hronograph...19 Thermometer...20 arometer...21 ompass...22 Head setting...23 Declination and calibration...24 ltimeter...25 Interval setting...26 ltitude calibration...27 Parameter...16 International Warranty...133

3 !"!'%.!')%&#&' )%*!++ (,')-) "$/,# #,&'%)%&#&' General information ongratulations on the purchase of a Roamer TrekkMaster. Your TrekkMaster is a highly advanced electronic device. Therefore we recommend that you carefully read the instructions before use to familiarize yourself with its functions. Please note that a piece of precision electronics like the TrekkMaster will only work as it should if you know how to use it. Improper use and maintenance of this device may void the warranty and place you in unnecessary danger. WRNING: Please remember that you are always responsible for your own safety. The TrekkMaster in no way reduces the need for the security precautions associated with your activities. Do not use this device for activities which require professional or industrial measuring accuracy. Do not use the TrekkMaster for measurements during the following types of sports: Skydiving, hang-gliding, paragliding or flying with a gyrocopter, sailplane, motorized sport plane, etc. Professional measuring devices are required for these activities. 5

4 Functional overview arometer ompass N W E S Thermometer hronometer How to change mode Light Weather Indicator Sensor Rotating ezel Pusher Date Pusher LD Display Pusher ltimeter 4478m larm Push and move between the modes by pushing (counterclockwise) or (clockwise). onfirm your selected mode by pushing again (or wait for 30 sec). 6 Time-1 Time-2 7

5 Model overview Model overview

6 Synchronizing hands Low attery 10 Following a battery change, a violent impact or exposure to a strong magnetic field, hands may fail to revert to their original position. From each mode, push for at least 3 sec. Use (h) and (min) to synchronize hands. Push to exit. When Low attery is detected, all functions are disabled and hands are placed at 12h00. If larm was ON it will not be disabled until it goes off. Note: acklight or running chrono in the background reduces battery life. 11

7 acklight Settings 12 The TrekkMaster has an electroluminescent backlight which is activated by pushing the «Light» button. The backlight will remain on for 5-seconds. Pressing the «Light» button during this time will restart the 5 second period, continuing the backlight feature. Water Resistance This product is water resistant. Water resistance is tested to 50m. Make always sure that crown is always in the pushed-in position in order to ensure the water resistance of the watch. To edit one of them, push to confirm mode and again to adjust flashing display then push to set and confirm edited mode. To exit settings mode, push from any step. To set Time-1, Date and parameters, press at least 1 second on from Time-1 mode (or pull from each mode), hands are placed at 10h10. Push to jump between Time-1, Date and parameters. 13

8 Time-1 year %& hours &$ Date 14 seconds To edit Time-1, push to confirm mode Time-1 and again to adjust flashing display then push to set and confirm hours, minutes and seconds. Push to jump to Date setting or push to exit settings mode. month &) day To edit Date, push to confirm mode Date and again to adjust flashing display then push to set and confirm year, month and day. Push to jump to Parameter setting or push to exit settings mode. '( minutes!"#$ 15

9 Time-2 hours 16 chime --/on To edit Param, push to confirm mode Param and again to adjust flashing display followed by pushing to set and confirm 12h/24h, m/ft and chime --/on. Push to jump to Time-1 setting or push to exit settings mode. &) unit m/ft minutes To adjust Time-2, push in Time-2 mode at least 1 second, hands are placed at 10h10 and hours are flashing. To change hours/minutes use button, to set and confirm push. Note: Time-2 is always in 30min intervals relative to Time-1. '( %& unit / F!"#$ &$ Parameter 17

10 larm hronograph Each action place hands at 10h10 for 20 seconds. hours 18 To set the larm (off/on) push in larm mode. To adjust larm time push at least 1 second, hands are placed at 10h10. To change hours/minutes/status use button, to set and confirm push. To exit settings mode quickly push. reset freeze/unfreeze Push to start/stop the chrono in chrono mode. Push to freeze/unfreeze or reset the chrono. Note: s long the pictograms are blinking, the chrono is running. You can switch to another operation while chrono is running. '( minutes &) %& start/stop!"#$ &$ status --/on 19

11 Thermometer arometer 20 Restart measure for 20s, hands are placed at 10h10 Precise outside temperature is shown on the display in unit selected ( or F) > chapter settings Hands are placed at 10h10 for 20 seconds Note: For the best reading of the temperature, remove the watch from your wrist and wait for approximately minutes. When Thermometer is in standby mode hands are placed at Time-1. The arometer function shows the weather changes via the relative atmospheric pressure on the digital display in hpa it indicates a trend. When arometer is in standby mode hands are placed at Time-1. Restart measures for 20 seconds 17 last measures made every 30 minutes tmospheric pressure in hpa Hands are placed at 10h10 for 20 seconds, measure is updated 21

12 ompass Head setting ompass Head ngle between North and 12h North Restart measure for 20 seconds 1 sec: Head setting To exit settings mode 1 sec: ompass declination and calibration + - To exit settings mode 22 Indicates geographic North using magnetic North and the adjustable East and West declination. When ompass is in standby mode hands are placed at Time-1. To adjust Head push at least 1 second, hands are placed at 10h10. Push on or to change Head. To exit settings mode push the crown, or wait for 5 sec. 23

13 24 ompass Declination and alibration Declination can be set from 40 East to 40 West. To calibrate ompass Hands will run, turn the watch to keep hand in front of you. When calibration is finished the compass get out of settings mode. Restart measures for 20 sec and erases old graph 1 sec: Interval setting 17 measures made at the interval selected To exit settings mode ltitude Hands are placed at 10h10 for 20 sec and ltitude is updated 1 sec: ltitude calibration ltimeter djustable display of the altitude above sea level in m/ft. The calculation depends on the atmospheric pressure. For correct use of the altimeter, calibrate it as frequently as possible. When ltimeter is in standby mode hands are placed at Time-1. 25

14 ltimeter Interval setting ltitude calibration ltimeter 26 hoose Interval Measuring time 1 s 0h s 0h s 0h min 0h min 1h min 4h min 8h30 00 eep signal indicates end of new measurement To adjust Interval measure push for at least 1 sec, hands are placed at 10h10. Push again to choose interval: 1s, 5s, 20s, 1min, 5min, 15min or 30min. To exit settings mode push the crown, or wait for 5 sec. + - To exit settings mode To calibrate ltimeter push for at least 1 second, hands are placed at 10h10. Push to add or to subtract metres/feet. To exit settings mode push the crown, or wait for 5 sec. 27