Ni - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY.

Size: px
Start display at page:

Download "Ni - Cd THIS PRODUCT CONTAINS A RECHARGEABLE NICKEL-CADMIUM BATTERY. THE BATTERY MUST BE RECYCLED OR DISPOSED OF PROPERLY."

Transcription

1 50 it Installation Instructions SF-TIN RN QUIPNT UNIVRS INPUT! IPORTNT SFURDS! WHN USIN TRI QUIPNT, SI SFT PRUTIONS SHOUD WS FOOWD, INUDIN TH FOOWIN: RD ND FOOW SFT INRUTIONS 1. To prevent high voltage from being present on red & yellow output leads prior to installation, inverter connector must be open. Do not join inverter connector until installation is complete and power is supplied to the emergency ballast. 2. This product is for use with one 17 W through 215 W (2-8 ) or two 17 W through 40 W (2-4 ) single pin or bipin fluorescent lamps, including standard, energy saving, HO, VHO, circline, U-shaped and rapid-start (4-pin) long compact fluorescent lamps. 3. ake sure all connections are in accordance with the National lectrical ode or anadian lectrical ode and any local regulations. 4. To reduce the risk of electric shock, disconnect both normal and emergency power supplies and inverter connector of the emergency ballast before servicing. 5. This emergency ballast is for factory or field installation in either the ballast channel, on top of, or remote from the fixture. 6. This product is suitable for damp locations where the ambient temperature is 0 minimum, +50 maximum. Product is also suitable for installation in sealed and gasketed fixtures. Product is not suitable for heated air outlets and wet or hazardous locations. 7. n unswitched power source is required. (120 through 277 V, 50/60Hz) 8. Do not install near gas or electric heaters. 9. Do not attempt to service the battery. sealed, no-maintenance battery is used that is not field replaceable. ontact the manufacturer for information on service. 10. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 11. Do not use this product for other than intended use. 12. Servicing should be performed by qualified service personnel. SV THS INRUTIONS Ni - d THIS PRODUT ONTINS RHR NI-DIU TTR. TH TTR U RD OR DISPOSD OF PROPR. 05/18/12 Philips mergency ighting Division of Philips lectronics North merica orporation 236 t. Pleasant Rd. ollierville, TN US Tech Support Fax

2 INTION WRNIN: TO PRVNT HIH VOT FRO IN PRSNT ON & OW OUTPUT DS PRIOR TO INTION, INVRTR ONNTOR U OPN. DO NOT JOIN INVRTR ONNTOR UNTI INTION IS OPT ND POWR IS SUPPID TO TH RN. NOT: ake sure the necessary branch circuit wiring is available. n unswitched source of power is required. The emergency ballast must be fed from the same branch circuit as the ballast. P #1 ININ TH RN > Disconnect power from the fixture. Remove the ballast channel cover and install the emergency ballast either in the ballast channel or on top of the fixture.* Remote mounting distance must be less than half the maximum remote mounting distance for the ballast. onsult ballast manufacturer before remote installation. > Depending on the type of fixture in use install emergency ballast using one of the methods illustrated below. INSID Inside allast hannel HNN INSID Inside RIP Strip Fixture FIXTUR ON On TOP Top OF of Fixture FIXTUR * For installation on top of the fixture, wire bundle covers (R-60) may be required by state or local codes. These covers are available from the manufacturer as an accessory kit and must be ordered separately. all your local distributor or the factory for complete information. P #2 ININ TH T > Refer to the illustrations above and install the test switch through the ballast channel cover of a troffer or through the side of a strip fixture. Fixture Test utton Hex Nut Test Switch > Drill a 1/2 hole and install the switch as shown. > Wire the test switch so that it removes power from both the emergency ballast and the ballast at the same time. (see wiring diagrams) Push to Test eads Hex Nut P #3 ININ TH HRIN INDITOR IHT > Install the HRIN INDITOR IHT as shown in the illustration on the following page so that it will be visible after the fixture is installed. 2

3 HRIN INDITOR IHT INTION TROFFR FIXTUR RIP FIXTUR Fixture Fixture harging Indicator ight harging Indicator ight Violet (+) Violet (+) rown ( ) rown ( ) 1/2" White ushing 1/2" Punch 5/8" lack ushing 1/2" White ushing 5/8" lack ushing P #4 WIRIN TH RN > Determine the type of ballast installed in the fixture. > Select the appropriate wiring diagram on back to connect the emergency ballast to the ballast and lamp(s). ake electrical connections in accordance with the National lectrical ode and any local regulations. > fter installation is complete, supply power to the emergency ballast and join the inverter connector. It is normal for the indicator light to remain off for a few minutes on initial start-up, as the battery voltage rises to normal range. Refer to Troubleshooting uide if this condition persists. > t this point, power should be connected to both the ballast and the emergency ballast, and the harging Indicator ight should illuminate indicating the battery is charging. > short-term discharge test may be conducted after the emergency ballast has been charging for one hour. harge for 24 hours before conducting a long-term discharge test. Refer to OPRTION. > In a readily visible location, attach the label UTION - This Unit Has ore Than One Power onnection Point. To Reduce The Risk Of lectric Shock, Disconnect oth The ranch ircuit-reakers Or Fuses nd mergency Power Supplies efore Servicing. OPRTION During normal operation, power is applied and the self-testing emergency ballast charges the battery. onnecting the (red and white) inverter connector wires enables the emergency circuit, and supplies power to the control/monitor circuit and charging indicator light. The self-testing emergency ballast continually monitors the charging current and battery voltage, comparing them to preset limits. Should the unit detect an unusual current or voltage condition, the indicator light will flash a pattern as mentioned in the troubleshooting guide until the condition has been corrected or the unit passes the next test. When power fails, the self-testing emergency ballast automatically switches to emergency mode, keeping either one or two lamps illuminated at a reduced lumen output for a minimum of 90 minutes. When power is restored, the self-testing emergency ballast returns to charging mode and delays ballast operation for approximately three seconds to prevent false tripping of ballast (end-of-lamp life) shutdown circuits. SF-TIN OPRTION This unit contains a control/monitor circuit that automatically performs a 30-second discharge test every 30 days, and a full 90-minute discharge test once a year. During routine testing, the self-testing emergency ballast simulates an power failure causing the unit to automatically switch to emergency mode. The unit will monitor the operation of the lamps, battery voltage, discharge current, and emergency duration. If the emergency system functions properly, then the unit will return to normal mode. Should the unit detect any problems, the indicator light will flash a pattern as mentioned in the troubleshooting guide until the condition has been corrected or the unit passes the next test. To reset a failure indication, push and hold the test switch for a minimum of 15 seconds. If the condition has not been corrected by the next scheduled test, the unit will once again detect the failure and signal the failure indicator. To cancel a test, turn the wall switch ON (or OFF if switch is already on), wait five seconds, then turn it OFF (ON). 3

4 INTNN This self-testing emergency ballast automatically performs required routine testing. Results are reported to maintenance personnel via the indicator light. Note: aintenance personnel should periodically check the indicator light. If the indicator light is flashing, go through all steps of Troubleshooting uide. TROUSHOOTIN UID TUS INDITOR PRO ORRTIV TION ight on steady, not flashing None None, Unit is Operating orrectly. Flashing 2 times every 10 seconds attery voltage is outside limits et battery charge. If after an hour failure is still indicated, see action below. Flashing 3 times every 10 seconds attery charging current is outside limits heck that fixture wiring is in accordance with proper wiring diagram. Flashing 4 times every 10 seconds ontinuous fast flashing attery discharge is too low during scheduled self test attery discharge is too high during scheduled self test 1. heck to make sure lamps are good (operational and specified for self-testing emergency ballast) and in place. 2. heck to see if brown connector is properly used. (See Table 1.) 3. heck that fixture wiring is in accordance with proper wiring diagram. 4. llow unit to charge for 24 hours. Perform manual test. If flashing continues, emergency ballast should be replaced. Failure Status will be reset when the unit passes: The next automatic test, or manual test exceeding 15 seconds, or n actual power failure exceeding 15 seconds. 4

5 50 WIRIN DIRS The following diagrams are typical schematics only. ay be used with other ballasts. onsult the factory for other wiring diagrams. mergency allast and allast must be fed from the S RNH IRUIT. IPORTNT TXT: RFR TO T 1 RRDIN ROWN ONNTOR Table 1 ROWN ONNTOR OPN ROWN ROWN ROWN ONNTOR OSD JUPR WIR ROWN ROWN P (DITR) T8,T9,T10,T12 (1, 1¼, 1½ ) ON OPT S TP Single or ipin 4-PIN (211) WTT (ength) W (2'-4') W (5' -8') W NO. of PS (RN- OD) ROWN ONNTOR 1 OSD 2 OPN 1 OPN 1 OSD 2 OPN W 1 OSD WIRIN DIR for 1-P emergency operation FI ON (1) P RPID RT FI ON (1) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Refer to Table 1 before connecting ROWN OW P / U/WHT U U U 1 P RPID RT T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Refer to Table 1 before connecting P 1 P INNT RT FI TWO (2) P RPID RT FI D TWO (2) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U U 2 P RPID RT WRNIN: Refer to Table 1 before connecting OW OW P 1 ( RN) P 2 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Refer to Table 1 before connecting P 1 ( RN) U P 2 2 P INNT RT FI THR (3) P RPID RT FI F THR (3) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U U 3 P RPID RT WRNIN: Refer to Table 1 before connecting U/WHT OW OW U/WHT P 1 ( RN) P 2 P 3 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U 3 P INNT RT WRNIN: Refer to Table 1 before connecting U U P 1 ( RN) P 2 P 3 FI FOUR (4) P RPID RT FI H FOUR (4) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U 4 P RPID RT WRNIN: Refer to Table 1 before connecting OW OW U/WHT U/WHT RN RN U U P 1 ( RN) P 2 P 3 P 4 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U 4 P INNT RT WRNIN: Refer to Table 1 before connecting OW U OW P 1 ( RN) P 2 P 3 P 4 5

6 FI I RN ND U FD FRO TH S RNH IRUIT TPI SHTIS ON. USD WITH OTHR S. ONSUT TH FTOR FOR OTHR WIRIN DIRS. WIRIN DIR for 1-P emergency operation ON (1) P OPT RPID RT FI J TWO (2) P OPT RPID RT W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Refer to Table 1 before connecting ROWN OW / P U/WHT U U U 1 P RPID RT T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U U 2 P RPID RT WRNIN: Refer to Table 1 before connecting OW OW P 1 ( RN) P 2 FI TWO (2) P RPID RT P DIIN WHT/ INVRTR ONNTOR VIOT (+) HRIN INDITOR ROWN (-) T WHT/ S1 S2 R N ROWN ROWN OW / U/WHT U U U 2 P RPID RT P DIIN WRNIN: Refer to Table 1 before connecting OW OW P 1 ( RN) P 2 TH / D U ONNT TO TH D OF TH P-DIIN SSOITD WITH TH RN ON. ONNTIONS TO OTHR S OR FIXTURS OUD RSUT IN NOR OPRTION ND US PRODUT D. WIRIN DIRS for 2-P emergency operation (2-4, W lamps only) Two-lamp emergency operation is not possible with all ballasts. onsult the factory for any ballast other than those shown. FI TWO (2) P RPID RT FI TWO (2) P INNT RT T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Do NOT connect brown connector ROWN OW P 1 / U/WHT U U U P 2 2 P RPID RT OW OW T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Do NOT connect brown connector P 1 U P 2 2 P INNT RT FI N THR (3) P RPID RT FI O THR (3) P INNT RT W W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN WRNIN: Do NOT connect brown connector OW P 1 ( RN) / U/WHT U U/WHT U U U/WHT OW P 2 ( RN) 3 P OW RPID RT P 3 T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U 3 P INNT RT WRNIN: Do NOT connect brown connector U U P 1 P 2 P 3 ( RN) ( RN) FI P FOUR (4) P RPID RT FI Q FOUR (4) P INNT RT T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: Do NOT connect brown connector ROWN OW P 1 ( RN) / U/WHT OW U OW U/WHT P 2 ( RN) U/WHT 4 P RPID RT P 3 RN RN U P 4 U T W INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN ROWN OW / U/WHT U U WRNIN: Do NOT connect brown connector P 1 ( RN) OW U P 2 ( RN) 4 P INNT RT P 3 OW P 4 FI R TWO (2) OPT P RPID RT W T INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) WHT/ R N ROWN WRNIN: DO NOT connect brown connector ROWN OW / P 1 U/WHT U OW U U 2 P RPID RT OW P 2 6

7 WIRIN DIRS for mergency-only fixtures FI S ON (1) P WITHOUT (16W-215W) FI T TWO (2) PS WITHOUT (17W-40W) T (P) INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) R N ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Refer to Table 1 before connecting P T (P) INVRTR ONNTOR HRIN INDITOR WHT/ VIOT (+) ROWN (-) R N ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Do NOT connect brown connector P 1 P 2 (P) WHT/ (P) WHT/ FI U ON (1) 4-PIN OPT P WITHOUT (16W-55W) FI V TWO (2) 4-PIN OPT PS WITHOUT (16W-39W) T (P) WHT/ INVRTR ONNTOR HRIN VIOT (+) INDITOR ROWN (-) (P) WHT/ R N S T ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Refer to Table 1 before connecting P T (P) WHT/ INVRTR ONNTOR HRIN VIOT (+) INDITOR ROWN (-) (P) WHT/ R N S T ROWN ROWN OW / U/WHT U (P) (P) WRNIN: Do NOT connect brown connector P 1 P 2 7

IMPORTANT SAFEGUARDS

IMPORTANT SAFEGUARDS ins chemicals known to the State of alifornia to cause can UFO-6W mergency ighting Fluorescent attery Pack INTION INRUTIONS - uto Select IPORTNT SFURDS When using electrical equipment, basic safety precautions

More information

Stand-Alone Bubble Detection System

Stand-Alone Bubble Detection System Instruction Sheet P/N Stand-Alone Bubble Detection System 1. Introduction The Bubble Detection system is designed to detect air-bubble induced gaps in a bead of material as it is being dispensed. When

More information

36G22, 36G23, 36G24 & 36G52 36J22, 36J23, 36J24 & 36J52 DSI and HSI Single Stage Combination Gas Valve

36G22, 36G23, 36G24 & 36G52 36J22, 36J23, 36J24 & 36J52 DSI and HSI Single Stage Combination Gas Valve Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION

More information

SPECIFICATIONS ATTENTION

SPECIFICATIONS ATTENTION VPS 504 S06 Installation Manual - P/N 80122 - Ed. 01/09 VPS 504 S06 and S05 Valve Proving System Installation Instructions VPS 1 6 Gases Natural gas, air and other inert gases. NOT suitable for butane

More information

Installation Instructions

Installation Instructions Installation Instructions Low-Ambient Pressure Switch KSALA0201R22 KSALA0301410 NOTE: Read the entire instruction manual before starting the installation. SAFETY ONSIDERATIONS Improper installation, adjustment,

More information

BUBBLER CONTROL SYSTEM

BUBBLER CONTROL SYSTEM BUBBLER CONTROL SYSTEM Description: The HDBCS is a fully automatic bubbler system, which does liquid level measurements in water and wastewater applications. It is a dual air compressor system with, air

More information

Installation Instructions

Installation Instructions Low -Ambient Pressure Switch 0201R22 0301410 Installation Instructions NOTE: Read the entire instruction manual before starting the installation. SAFETY ONSIDERATIONS Improper installation, adjustment,

More information

SRL-1. Audio controlled cirquit breaker USER MANUAL

SRL-1. Audio controlled cirquit breaker USER MANUAL SRL-1 Audio controlled cirquit breaker USER MANUAL Audio Controlled Circuit Breaker DATEQ SRL-1 Introduction The SRL-1 is build as relay extension box for the SPL3, SPL3TS, SPL5 and SPL-D2 display. Linked

More information

Universal Valve Company Inc

Universal Valve Company Inc Universal Valve Company Inc 800-223-0741 www.universalvalve.com 1975-FA34 (Air Tower Troubleshooting Manual) Overview This manual has been arranged as a tool for diagnosing, and repairing Free Air Universal

More information

Universal Valve Company Inc

Universal Valve Company Inc 1975-FA34 (Air Tower Troubleshooting Manual) Overview This manual has been arranged as a tool for diagnosing, and repairing Universal Air Towers Please read closely to identify the components that are

More information

User Manual. Heads-Up Display (HUD) DiveCAN. Mechanical Button Version

User Manual. Heads-Up Display (HUD) DiveCAN. Mechanical Button Version User Manual Heads-Up Display (HUD) Mechanical Button Version DiveCAN Table of Contents 1. Introduction...4 1.1 Features...4 2. Physical Description...5 3. Reading the PPO2...6 3.1 Modified Smither s Code...7

More information

Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units

Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Models: EPS Single Pump EPT Twin Pump EPS-HP EPT-HP Single Pump High Pressure Twin Pump High Pressure

More information

AUTOMATIC GAS MANIFOLDS

AUTOMATIC GAS MANIFOLDS AUTOMATIC GAS MANIFOLDS Phoenix Pipeline Products Limited. Unit 8, McKenzie Industrial Park, Tel No.: 44 (0) 161 428 7200 Bird Hall Lane, Fax No.: 44 (0) 161 428 7010 Stockport, Email: info@p3-phoenix.com

More information

For Models: 55A00-2 (HAI UPB 1500W Wall Switch Dimmer) 55A00-3 (HAI UPB 2400W Wall Switch Dimmer) 37A00-1 (HAI Auxiliary Switch)

For Models: 55A00-2 (HAI UPB 1500W Wall Switch Dimmer) 55A00-3 (HAI UPB 2400W Wall Switch Dimmer) 37A00-1 (HAI Auxiliary Switch) HAI UPB High Power Wall Switch Dimmer and HAI Auxiliary Switch Installation and Operating Instructions For Models: 55A00-2 (HAI UPB 1500W Wall Switch Dimmer) 55A00-3 (HAI UPB 2400W Wall Switch Dimmer)

More information

EDUCATION DEPARTMENT ACCU-TEST

EDUCATION DEPARTMENT ACCU-TEST ABN 17 100 208 964 EDUCATION DEPARTMENT ACCU-TEST GAS SAFETY SHUT OFF SYSTEM Operating & Installation Manual Head Office (Melbourne) Sydney Brisbane (Distributor) 1/5 Samantha Court 2/14 Welder Road 17

More information

MODELS (2 foot Version) (4 foot Version)

MODELS (2 foot Version) (4 foot Version) INSTALLATION AND MAINTENANCE MANUAL DUROSITE LED LINEAR FIXTURE Document No: 9100-127-2571-99 Rev A April, 2016 MODELS (2 foot Version) (4 foot Version) ALL LAE ALL LBE These instructions contain important

More information

Operator: Save these instructions for future use!

Operator: Save these instructions for future use! INLET PRESS TAP WHITE-RODGERS 36E93-304 Delay-Opening Combination Gas Valve INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

More information

200 PSI COMPRESSORS - MODEL NUMBERS

200 PSI COMPRESSORS - MODEL NUMBERS 200 PSI COMPRESSORS - MODEL NUMBERS 380C AIR COMPRESSOR KIT PART NO. 38033 480C AIR COMPRESSOR KIT PART NO. 48043 380C 480C IMPORTANT: It is essential that you and any other operator of this product read

More information

100C Air Compressor Kit

100C Air Compressor Kit 10010 100C Air Compressor (standard mounting bracket, CE Spec) 10014 100C Air Compressor (no leader hose or check valve, CE Spec) 10016 100C Air Compressor (with Omega Bracket, CE Spec) IMPORTANT: It is

More information

AMP Oil Free Manual AMP 50-8-TC AMP 50-6-D AMP General User and Maintenance Instructions

AMP Oil Free Manual AMP 50-8-TC AMP 50-6-D AMP General User and Maintenance Instructions AMP Oil Free Manual AMP 50-8-TC AMP 50-6-D AMP 50-24 General User and Maintenance Instructions Silentaire Technology 8614 Veterans Memorial Dr. Houston, TX 77088 800-972-7668 Fax 832-327-0669 www.silentaire.com

More information

Installation & Maintenance Instructions TEC-11N TIMER. Analogue electronic timer 02/09

Installation & Maintenance Instructions TEC-11N TIMER. Analogue electronic timer 02/09 Installation & Maintenance Instructions TEC-11N TIMER Analogue electronic timer 02/09 GENERAL OPERATION The TEC-11N timer is produced using SMT (Surface Mounting Technology), ensuring improved performance

More information

420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO

420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO 420C AIR COMPRESSOR KIT PART NO. 42042 460C AIR COMPRESSOR KIT PART NO. 46043 420C 460C IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock: - Do not disassemble. Do not attempt repairs or modifications. Refer to qualified service agencies for all service and repairs.

More information

This Manual Part recommends functional/operating guidelines for control of automatic grade crossing warning systems. Draft

This Manual Part recommends functional/operating guidelines for control of automatic grade crossing warning systems. Draft Recommended Functional/Operating Guidelines for Control of Automatic Grade Crossing Warning Systems Revised 2017 (6 Pages) A. Purpose This Manual Part recommends functional/operating guidelines for control

More information

Model PSI Compressor with 3-Gallon Air Tank 12VDC

Model PSI Compressor with 3-Gallon Air Tank 12VDC Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing

More information

Misaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii

Misaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii Operator s Manual Table of Contents Operator Safety... 1 Introduction... 2 Unpacking and Setup... 3 Unpacking... 3 Setup... 4 FLYER Overview... 5 FLYER Diagram... 5 Capabilities... 5 Control Panel... 6

More information

RAM Operation Manual

RAM Operation Manual RAM 4021-1 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-1 For Your Safety... 2 Description... 2 Setup Mode... 3 Lights/Alarms... 3 Operation... 4 Calibration...

More information

Proportional Pressure-Relief Cartridge Valve, Size 2...4

Proportional Pressure-Relief Cartridge Valve, Size 2...4 Proportional Pressure-Relief Cartridge Valve, Size... Q max = l/min (6 gpm), p max = bar (58 psi) Direct acting, electrically operated Description proportional pressure-relief valves are direct acting

More information

L230 LED 40 Watt Searchlight

L230 LED 40 Watt Searchlight User Instruction & Installation Manual L230 LED 40 Watt Searchlight Product Reference Number: A6158 12/24v DECK A6159 12/24v CABIN Manufacturer s details: Francis Searchlights Ltd Union Road, Bolton Lancashire,

More information

Budget Range Operators Handbook

Budget Range Operators Handbook Budget Range Operators Handbook BAMBI AIR COMPRESSORS LTD 152 Thimble Mill Lane Heartlands Birmingham B7 5HT United Kingdom Tel: 0121 322 2299 Fax: 0121 322 2297 Email: sales@bambi-air.co.uk www.bambi-air.co.uk

More information

Pressure Dump Valve Service Kit for Series 3000 Units

Pressure Dump Valve Service Kit for Series 3000 Units Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator

More information

444C DUAL PERFORMANCE VALUE PACK

444C DUAL PERFORMANCE VALUE PACK (Chrome) PART NO. 44432 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL

More information

Proportional Pressure-Relief Cartridge Valve, Size 2...4

Proportional Pressure-Relief Cartridge Valve, Size 2...4 Proportional Pressure-Relief Cartridge Valve, Size... Q max = l/min, p max = 3 bar Direct acting, electrically operated 1 Description proportional pressure-relief valves are direct acting screw-in cartridges

More information

References 6 k thermal overload relays, adjustable from 0.11 to 16 A

References 6 k thermal overload relays, adjustable from 0.11 to 16 A s 6 k thermal overload relays, adjustable from 0.11 to 16 A 3-pole relays with screw clamp terminals These overload relays are designed for the protection of motors. They are compensated and phase failure

More information

RAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions

RAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4 Calibration....

More information

MOYNO FLUID DETECTION CONTROL SERVICE MANUAL. Section: ACCESSORIES. Page: 1 of 8 Date: May 1, 1998 GENERAL

MOYNO FLUID DETECTION CONTROL SERVICE MANUAL. Section: ACCESSORIES. Page: 1 of 8 Date: May 1, 1998 GENERAL MOYNO Section: ACCESSORIES Page: 1 of 8 Date: May 1, 1998 SERVICE MANUAL FLUID DETECTION CONTROL GENERAL The Moyno Fluid Detection Control prevents unnecessary loss of production time or repair costs to

More information

INSTALLATION & MAINTENANCE INSTRUCTION

INSTALLATION & MAINTENANCE INSTRUCTION ARCHON Industries, Inc Liquid Level Gauges Models: BT-LLG ND-LLG INSTALLATION & MAINTENANCE INSTRUCTION Instruction No.: 1014.2 Revision Issued: 3/01/03 Approved: Engineering Manager Warning ONLY QUALIFIED

More information

ACV-10 Automatic Control Valve

ACV-10 Automatic Control Valve ACV-10 Automatic Control Valve Installation, Operation & Maintenance General: The Archer Instruments ACV-10 is a precision automatic feed rate control valve for use in vacuum systems feeding Chlorine,

More information

sensazone sensazone is an intelligent PIR sensor operated system which controls the water supply and the light and fan functions in washrooms.

sensazone sensazone is an intelligent PIR sensor operated system which controls the water supply and the light and fan functions in washrooms. sensazone installation guide 1 System requirements sensazone is an intelligent PIR sensor operated system which controls the water supply and the light and fan functions in washrooms. The system features

More information

Manual Leveling Control Installation/Operation

Manual Leveling Control Installation/Operation ELECTROMECHANICAL TRIM TAB SYSTEMS Manual Leveling Control Installation/Operation Linear Devices Corporation dba Lectrotab 11126 Air Park Road, Suite G Ashland, VA 23005 www.lectrotab.com Phone: 804-368-8428

More information

Coastal Amusements 1935 Swarthmore Ave. Lakewood NJ Tel: (732) Fax: (732)

Coastal Amusements 1935 Swarthmore Ave. Lakewood NJ Tel: (732) Fax: (732) Revision G 1/14/05 Coastal Amusements 1935 Swarthmore Ave. Lakewood NJ 08701 Tel: (732)-905-6662 Fax: (732)-905-6815 Table of Contents Introduction 1 Game Setup 1 Game Play 1 Maintenance 1 Glossary of

More information

MULTIFUNCTIONAL CONTROL FOR GAS BURNING APPLIANCE

MULTIFUNCTIONAL CONTROL FOR GAS BURNING APPLIANCE SIT Group SIT -3- SIGMA MULTIFUNCTIONAL CONTROL FOR GAS BURNING APPLIANCE 9.955. Subject to change without notice Application Domestic gas appliances: central heating boilers, combi boilers, instantaneous

More information

HAI UPB Wall Switch and Auxiliary Switch Installation and Operating Instructions

HAI UPB Wall Switch and Auxiliary Switch Installation and Operating Instructions HAI UPB Wall Switch and Auxiliary Switch Installation and Operating Instructions For the following Models: 35A00-1 HAI 600W Dimmer Switch, 35A00-3 HAI 600W Non-Dimming Switch (collectively referred to

More information

icreasepro Creaser Operators Manual

icreasepro Creaser Operators Manual 6-2013 Version 3.0 icreasepro Creaser Operators Manual WWW.MBMCORP.COM 800-223-2508 TABLE OF CONTENTS SPECIFICATIONS.1a SAFETY PROCEDURES/CARE & MAINTENANCE..1b COMPONENT IDENTIFICATION 2 TOUCH SCREEN

More information

Inverse Prop. Pressure-Relief Cart., Size 2 4

Inverse Prop. Pressure-Relief Cart., Size 2 4 Inverse Prop. Pressure-Relief Cart., Size Q max = l/min (6 gpm), p max = bar (58 psi) Direct acting, electrically operated Description inverse proportional pressure-relief valves are direct acting screw-in

More information

Operating Instructions

Operating Instructions Addingham Cricket Club, Leeds Operating Instructions Introduction Bespoke Scoreboards Operating Instructions The information displayed on your Scoreboard is changed using the Scoreboard controller. This

More information

Inverse Proportional Pressure-Relief Cart., Size 2 4

Inverse Proportional Pressure-Relief Cart., Size 2 4 Inverse Proportional Pressure-Relief Cart., Size Q max = l/min, p max = 35 bar Direct acting, electrically operated Description Compact construction for cavity type AL 3/-6 UNF Operated by a proportional

More information

OC Panel High Limit Aquastat Kit, Manual Reset p/n

OC Panel High Limit Aquastat Kit, Manual Reset p/n OC Panel High Limit Aquastat Kit, Manual Reset p/n 233202 Instruction Sheet APPLICATION The OC (Option Control) Panel High Limit Aquastat Kit provides electronic temperature sensing in a UL limit-rated

More information

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO 250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual

More information

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO 250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual

More information

RIX COMPRESSORS. MICROBOOST Owner s Manual CONFIGURATION A MB-115 MB-230. November 21, 2002 APPLICABILITY [ A]

RIX COMPRESSORS. MICROBOOST Owner s Manual CONFIGURATION A MB-115 MB-230. November 21, 2002 APPLICABILITY [ A] RIX COMPRESSORS MICROBOOST Owner s Manual CONFIGURATION A MB-115 MB-230 November 21, 2002 APPLICABILITY [ A] INTRODUCTION Safety This electromechanical equipment is designed to produce high pressure gas.

More information

Scoreboard Operator s Instructions MPC Control

Scoreboard Operator s Instructions MPC Control Scoreboard Operator s Instructions MPC Control Some features on the keyboard overlay may not be included on the particular model being operated. Since 1934 Retain this manual in your permanent files 1/21/2011

More information

SC505 Sof Care Inflator. Operating Instructions and Service Manual

SC505 Sof Care Inflator. Operating Instructions and Service Manual SC505 Sof Care Inflator Gaymar Industries, Inc. 10 Centre Drive Orchard Park, NY 14127 Toll Free +1 800.828.7341 + 1 716.662.2551 Fax +1 800.993.7890 Outside USA +1 716.662.8636 Outside USA Fax +1 716.662.0730

More information

VR46.5V(A)/VR86.5V(A) SERIES

VR46.5V(A)/VR86.5V(A) SERIES VR46.5V(A)/VR86.5V(A) SERIES COMACT COMBINATION GAS CONTROS WITH INTEGRATED 1:1 GAS/AIR REGUATOR FOR AUTOMATIC IGNITION SYSTEMS SECIFICATIONS INSTRUCTION SHEET Subject to change without notice. rinted

More information

SPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.

SPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1. 2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or

More information

Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Digital Range

Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Digital Range Installation, Operation and Maintenance Instructions for Electronically Controlled Pressurisation Units Digital Range Models: DS 126 Single Pump / Single System DT 126 Twin Pump / Single System DS 160

More information

36E DSI, HSI & Proven Pilot Two-Stage Combination Gas Valve INSTALLATION INSTRUCTIONS

36E DSI, HSI & Proven Pilot Two-Stage Combination Gas Valve INSTALLATION INSTRUCTIONS INLET PRESS TAP WTE-RODGERS 36E96-314 DSI, HSI & Proven Pilot Two-Stage Combination Gas Valve INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL

More information

400C & 450C DUAL PERFORMANCE VALUE PACKS

400C & 450C DUAL PERFORMANCE VALUE PACKS (Chrome) PART NO. 40013 (Silver) PART NO. 45012 (Chrome) PART NO. 45013 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before

More information

RPS900W Redundant Power Supply. Installation Guide.

RPS900W Redundant Power Supply. Installation Guide. RPS900W Redundant Power Supply Installation Guide www.edge-core.com Installation Guide RPS900W Redundant Power Supply Single DC Output Port with Dual Output Voltages RPS900W E10013-CS-R01 1500000081A

More information

OEM Manual MODEL 2305 ECONOMICAL DIGITAL SINGLE CYLINDER SCALE

OEM Manual MODEL 2305 ECONOMICAL DIGITAL SINGLE CYLINDER SCALE OEM Manual MODEL 2305 ECONOMICAL DIGITAL SINGLE CYLINDER SCALE 1 These instructions generally describe the installation, operation, and maintenance of subject equipment. The manufacturer reserves the right

More information

Pressure Dump Valve Service Kit for Series 2300 Units

Pressure Dump Valve Service Kit for Series 2300 Units Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit

More information

Tank Continuous Liquid Level Detector

Tank Continuous Liquid Level Detector Tank ontinuous Liquid Level Detector Installation Manual FILE:. Written By: Joseph Bachor Date: 11/6/14 DD WIRE OLORS ND OUTLINE DRWING B LRIFITIONS JB 3/30/15 EN 5269 EN 255 hecked By: JOE B. pproved

More information

GAS FUEL VALVE FORM AGV5 OM 8-03

GAS FUEL VALVE FORM AGV5 OM 8-03 ALTRONIC AGV5 OPERATING MANUAL GAS FUEL VALVE FORM AGV5 OM 8-03 WARNING: DEVIATION FROM THESE INSTALLATION INSTRUCTIONS MAY LEAD TO IMPROPER ENGINE OPERATION WHICH COULD CAUSE PERSONAL INJURY TO OPERATORS

More information

Spectrum AquaLight (SAL ) Color Underwater Light Owner s Manual

Spectrum AquaLight (SAL ) Color Underwater Light Owner s Manual Spectrum AquaLight (SAL ) Color Underwater Light Owner s Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents Section I. Installing Light Fixture

More information

CDS-2000 CO 2 Sensor Verification, Calibration, and Troubleshooting Bulletin

CDS-2000 CO 2 Sensor Verification, Calibration, and Troubleshooting Bulletin Electronic Control Manual 216 Sensors and Stats Section S Technical Bulletin CDS-2000 Issue Date 0393 CDS-2000 CO 2 Sensor Verification, Calibration, and Troubleshooting Bulletin Introduction 3 Pre-Verification

More information

WARNING. I. About Your Trainer. II. Parts List. Notes: III. Assembly

WARNING. I. About Your Trainer. II. Parts List. Notes: III. Assembly Thank you for purchasing a Travel Trac trainer. The luid-mag orce Trainer provides the same speed, distance and ride time data available from a full-featured cycling computer, plus information on power

More information

SCIENTIFIC DATA SYSTEMS, INC. Depth Tension Line Speed Panel. DTLS Manual

SCIENTIFIC DATA SYSTEMS, INC. Depth Tension Line Speed Panel. DTLS Manual SCIENTIFIC DATA SYSTEMS, INC. Depth Tension Line Speed Panel DTLS Manual This document contains proprietary information. Copyright 2015 Scientific Data Systems, Inc. All rights reserved. 1 Depth Tension

More information

ServicePlus S21R & S27R Series 2 Installation Instructions

ServicePlus S21R & S27R Series 2 Installation Instructions ServicePlus S21R & S27R Series 2 Installation Instructions Horstmann Controls ServicePlus two channel service interval programmers have been developed to facilitate compliance with the Gas Safety (Installation

More information

Operating Instructions Part No

Operating Instructions Part No DIGITAL AUTOMATIC TYRE INFLATOR Operating Instructions Part No. 11.0578 Thank you for selecting this Jamec Pem Automatic Tyre Inflator. Please read this manual before carrying out any installation or service

More information

Control Units for Oil+Air Lubrication

Control Units for Oil+Air Lubrication Control Units for Oil+Air Lubrication 1-1700-3-US Universal Control Unit The control units described in this leaflet are used for timeor pulse-dependent control of oil+air systems. The overview shows the

More information

Operating instructions Safety Rope Emergency Stop Switches ZB0052 / ZB0053 ZB0072 / ZB0073

Operating instructions Safety Rope Emergency Stop Switches ZB0052 / ZB0053 ZB0072 / ZB0073 Operating instructions Safety Rope Emergency Stop Switches UK ZB0052 / ZB0053 ZB0072 / ZB0073 7390878 / 02 03 / 2011 Contents 1 Safety instructions...3 2 Installation / set-up...4 2.1 Applications...4

More information

HAI UPB 15A Relay Switch and Auxiliary Switch Installation and Operating Instructions

HAI UPB 15A Relay Switch and Auxiliary Switch Installation and Operating Instructions HAI UPB 15A Relay Switch and Auxiliary Switch Installation and Operating Instructions For the following Models: 40A00-1 HAI 15A Relay Switch (referred to as HAI UPB Wall Switch, in this document), and

More information

User manual. PCA EXCEL one4all with corridorfunction PCA T5 ECO lp with corridorfunction TE one4all with corridorfunction

User manual. PCA EXCEL one4all with corridorfunction PCA T5 ECO lp with corridorfunction TE one4all with corridorfunction User manual PCA EXCEL one4all with corridorfunction PCA T5 ECO lp with corridorfunction TE one4all with corridorfunction Contents 1 Introduction...2 2 Installation...2 3 Commissioning...3 4 corridorfunction

More information

36E DSI and HSI Two-Stage Combination Gas Valve INSTALLATION INSTRUCTIONS

36E DSI and HSI Two-Stage Combination Gas Valve INSTALLATION INSTRUCTIONS INLET PRESS TAP WTE-RODGERS 36E54-214 DSI and HSI Two-Stage Combination Gas Valve INSTALLATION INSTRUCTIONS Operator: Save these instructions for future use! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS

More information

RAM 4021-DPX Operation Manual

RAM 4021-DPX Operation Manual RAM 4021-DPX Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS ABL 4021-DPX / RAM 4021-DPX For Your Safety... 3 Description... 3 Setup Mode... 4 Lights/Alarms... 4 Operation...

More information

Model 130M Pneumatic Controller

Model 130M Pneumatic Controller Instruction MI 017-450 May 1978 Model 130M Pneumatic Controller Installation and Operation Manual Control Unit Controller Model 130M Controller is a pneumatic, shelf-mounted instrument with a separate

More information

Inverse Proportional Pressure-Relief Cart., Size 2 4

Inverse Proportional Pressure-Relief Cart., Size 2 4 Inverse Proportional Pressure-Relief Cart., Size Q max = l/min, p max = 5 bar Direct acting, electrically operated 1 Description inverse proportional pressure-relief valves are direct acting screw-in cartridges

More information

Sanitary RTD Temperature sensor TH17. Measuring System Sanitary RTD assembly with connection head TH17 for food and dairy applications.

Sanitary RTD Temperature sensor TH17. Measuring System Sanitary RTD assembly with connection head TH17 for food and dairy applications. Sanitary RTD Temperature sensor TH17 Compact Instructions Measuring System Sanitary RTD assembly with connection head TH17 for food and dairy applications. The single element RTD is specifi cally designed

More information

Inverse Proportional Pressure-Relief Cartridge, Size 10

Inverse Proportional Pressure-Relief Cartridge, Size 10 Inverse Proportional Pressure-Relief Cartridge, Size 1 Q max = 12 l/min, p max = 3 bar Seated pilot, spool-type main stage, damped design 1 Description inverse-proportional pressure-relief valves are size

More information

Management Plan for Electrical Safety ISD #535

Management Plan for Electrical Safety ISD #535 Management Plan for Electrical Safety ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9 ½ Street Rochester, MN 55904 507-328-4507 MANAGEMENT PLAN FOR ELECTRICAL SAFETY Table of Contents

More information

Instructions for Installation, Use and Maintenance FSI Safety Tank Shower Systems

Instructions for Installation, Use and Maintenance FSI Safety Tank Shower Systems Instructions for Installation, Use and Maintenance FSI Safety Tank Shower Systems per DIN 12 899 T1-3 and ANSI Z 358-2004 Table of Contents for Instructions for Use Section 1 Manufacturer, Safety Shower

More information

KEG PUMP. Range of Electric Keg Pumps

KEG PUMP. Range of Electric Keg Pumps KP KEG PUMP Range of Electric Keg Pumps Electric Keg (Drum) Pumps for Grease KEG PUMP Versatile range of Interlube electric grease pumps for industrial and off-road applications The KP keg pump is available

More information

NGP-250/500 Nitrogen Generator Quick Start Guide

NGP-250/500 Nitrogen Generator Quick Start Guide NGP-250/500 Nitrogen Generator Quick Start Guide Version: A July 2013 Potter Electric Signal Company, LLC 5757 Phantom Dr., Suite 125 P. O. Box 42037 Hazelwood, MO 63042 Phone: (314) 595-6900 Document

More information

BUBBLER CONTROL SYSTEM

BUBBLER CONTROL SYSTEM BUBBLER CONTROL SYSTEM Description: The LDBCS is a fully automatic bubbler system, which does liquid level measurements in water and wastewater applications. It is a dual air compressor system with, air

More information

with O 2 Controller Instruction Manual

with O 2 Controller Instruction Manual 14500 Coy Drive, Grass Lake, Michigan 49240 734-475-2200 E-mail: sales@coylab.com www.coylab.com Hypoxic Cabinets (In-Vivo / In-Vitro) with O 2 Controller Instruction Manual Index Page Warranty 2 Warnings

More information

Valve Proving System VDK 200 A S06*

Valve Proving System VDK 200 A S06* Valve Proving System VDK 200 A S06* Valve proving system with the following approvals. UL Recognized File # MH17004 CSA Certified File # 1637485 CSA Requirement No. 4-01 (USA) Technical Information Letter

More information

ORB-400 BUBBLE/HAZE MACHINE. Item ref: UK User Manual

ORB-400 BUBBLE/HAZE MACHINE. Item ref: UK User Manual ORB-400 BUBBLE/HAZE MACHINE Item ref: 160.462UK User Manual Caution: Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty Introduction Thank you for

More information

Valve Proving System VDK 200 A S02

Valve Proving System VDK 200 A S02 Valve Proving System VDK 200 A S02 Valve proving system with the following approvals. UL Recognized File # MH17004 CSA Certified File # 1637485 CSA Requirement No. 4-01 (USA) Technical Information Letter

More information

Sconce INSTALLATION INSTRUCTIONS P34022

Sconce INSTALLATION INSTRUCTIONS P34022 P34022 1 2016 of 12 KALLISTA THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product.

More information

RAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions

RAM Operation Manual. Worldwide Manufacturer of Gas Detection Solutions RAM 4021 Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021 For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4 Calibration....

More information

SG33KTL-M Quick Installation Guide. 1 Unpacking and Inspection

SG33KTL-M Quick Installation Guide. 1 Unpacking and Inspection SG33KTL-M Quick Installation Guide This guide provides a general instruction of the installation procedures of SG33KTL-M. In no case shall this guide substitute for the user manual or related notes on

More information

Concentrate Distribution System (Stand Mounted) A-CDS-70-X & A-CDS-TANK-X-ST Industrial Drive, Orlinda, TN 37141

Concentrate Distribution System (Stand Mounted) A-CDS-70-X & A-CDS-TANK-X-ST Industrial Drive, Orlinda, TN 37141 0 Operation Manual Concentrate Distribution System (Stand Mounted) A-CDS-70-X & A-CDS-TANK-X-ST 615-654-4441 sales@specialtyh2o.com 615-654-4449 fax TABLE OF CONTENTS Section 1 GENERAL 1.1 Warnings and

More information

12 Volt Inflator. Operator s Manual. Model: ICC12F, ICC12FC, ICC12FCN, ICC12FCM, ICC12N

12 Volt Inflator. Operator s Manual. Model: ICC12F, ICC12FC, ICC12FCN, ICC12FCM, ICC12N Operator s Manual 12 Volt Inflator Model: ICC12F, ICC12FC, ICC12FCN, ICC12FCM, ICC12N 873 E. Citation Court Boise, Idaho 83716 USA 800-874-5771 www.bon-aireindustries.com Safety Guidelines Assembly Operation

More information

RAM 4021-PR. Operation Manual. Worldwide Manufacturer of Gas Detection Solutions

RAM 4021-PR. Operation Manual. Worldwide Manufacturer of Gas Detection Solutions RAM 4021-PR Operation Manual Worldwide Manufacturer of Gas Detection Solutions TABLE OF CONTENTS RAM 4021-PR For Your Safety... 2 Description.... 2 Setup Mode.... 2 Lights/Alarms.... 3 Operation.... 4

More information

Operating Instructions Part No

Operating Instructions Part No DIGITAL AUTOMATIC TYRE INFLATOR Operating Instructions Part No. 11.0545 Thank you for selecting this Jamec Pem Automatic Tyre Inflator. Please read this manual before carrying out any installation or service

More information

TEL/jlRE" Introduction. Display Features and Modes. Startup Procedure. Power-Up Procedure. Adjustment Modes

TEL/jlRE Introduction. Display Features and Modes. Startup Procedure. Power-Up Procedure. Adjustment Modes TEL/jlRE" Introduction The Telaire 7001 CO 2 /T emperature monitor (shown in Fi gt u e 1 below) is an easy to use hand-held instnunent, which provides stable and highly accurate readings due to Telaire

More information

T i m i n g S y s t e m s. RACEAMERICA, Inc. P.O. Box 3469 Santa Clara, CA (408)

T i m i n g S y s t e m s. RACEAMERICA, Inc. P.O. Box 3469 Santa Clara, CA (408) RACEAMERICA T i m i n g S y s t e m s Demo Tree Controller Owner s Manual Models 3204D, 3204DW & 3204DX Rev D RACEAMERICA, Inc. P.O. Box 3469 Santa Clara, CA 95055-3469 (408) 988-6188 http://www.raceamerica.com

More information

ECONORESS ELECTRONIC EPS & EPT - ENHANCED PRESSURISATION SET INSTALLATION OPERATION & MAINTENANCE DOCUMENTATION

ECONORESS ELECTRONIC EPS & EPT - ENHANCED PRESSURISATION SET INSTALLATION OPERATION & MAINTENANCE DOCUMENTATION ECONORESS ELECTRONIC EPS & EPT - ENHANCED PRESSURISATION SET INSTALLATION OPERATION & MAINTENANCE DOCUMENTATION OCT2010 STOKVIS ENERGY SYSTEMS 96R WALTON ROAD EAST MOLESEY SURREY KT8 0DL TEL: 020 87833050

More information

Operation Manual. Pro He Alarm TM. Helium Analyzer. Rev 08.17

Operation Manual. Pro He Alarm TM. Helium Analyzer. Rev 08.17 Operation Manual Pro He Alarm TM Helium Analyzer Rev 08.17 If you have any questions on this equipment please contact Technical Support at: Nuvair 1600 Beacon Place Oxnard, CA 93033 Phone: 805-815-4044

More information

RTD Temperature sensor TH11

RTD Temperature sensor TH11 RTD Temperature sensor TH11 Compact Instructions Measuring System General purpose RTD with connection head TH11 for process and laboratory applications. The single element RTD is specifi cally designed

More information