THERMISTOR TYPE VORTEX FLOWMETER for GAS MEASUREMENT. DELTAFLOW Type F

Transcription

1 Gas THERMISTOR TYPE VORTEX FOWMETER for GAS MEASUREMENT DETAFOW Type F Standard and Gas Purge Types MODE: VF series GENERA SPECIFICATION GS.No. GENERA This flowmeter is a kind of vortex flowmeters, which makes use of the regular and periodic characteristics of Karman vortex street. A thermistor sensor picks up changes in flow velocity that come with vortex shedding in the manner - changes in thermistor temperature changes in resistance value a train of pulses proportional to the flow velocity. In the gas purge type, changes in fluid velocity that come with vortex shedding are replaced by changes in fluid velocity of a purge gas (clean gas) introduced from an external source. Thanks to this arrangement, the thermistor sensor constantly remains in contact with clean, room temperature purge gas, permitting precise flow measurement of gases containing dust and mist, high or low temperature gases, or others previously thought difficult to be measured. Wafer type Converter FEATURES 1. The absence of mechanical moving parts and components subject to abrasion ensures long life and continuous operation with no loss of accuracy with time. 2. By measuring actual flowrate, the measurement is insensitive to changes in fluid temperature, pressure and other physical properties. 3. Provides pulse output proportional to the flowrate to simplify totalization. 4. Small pressure loss saves energy. 5. Replaceable sensor facilitates maintenance and servicing without the need of interrupting the gas flow. 6. The converter separated from the sensor body may be located anywhere for maximum ease of maintenance irrespective of piping conditions. 7. Gas purge type is primarily intended for measuring gases containing dust and mist, or high or low temperature gases. GENERA SPECIFICATIONS Standard Meter Body Item Description Body style Wafer Flange Nominal size (mm) 20, 25, 32, (40), 50, 80, 100, , 250, 300, (350) 400, (450), 500 Meter body SUS304 STPG370 SUS304TP STPY400 SUS304TP Material ( 2) Flange SS400 or SFVC2A SUSF304 SFVC2A SUSF304 Bluff body SUS304 SCS13A or SUS304 Flange rating Companion flange JIS 10, 20, 30 K ASME/JPI 150, 300, (600) JIS 10, 20, 30 K ASME/JPI 150, 300, (600) ASME/JPI 150 Standard Connecting Pipe Sch40 Sch20 Operating temp. range 20 to to to to to +130 Design pressure 5.00MPa 1.89MPa Accuracy Within ±1% of RD or ±1% of FS ( 1) Repeatability Within ±0.2% Installation Horizontal or vertical 1: For use in the high pressure range (high Reynolds number [ or above]), contact OVA. 2: Material may vary according to specifications. 3: If the connecting pipe is different from standard connecting pipe, contact OVA. 4: For nominal size between 200 and 300mm with flange material SFVC2A, the max operating temperature ranges from 0 due to temperature limitation of the flange material. 5: Specifications in parentheses are non-standard/made-to-order. Maximum Operating Pressure Flange rating JIS10K JIS16K JIS20K JIS30K ASME/JPI150 ASME/JPI300 Max. operating pressure (MPa) Head Office (Tokyo): Tel Fax International Sales Division SK10@oval.co.jp Overseas Branch Offices: Beijing, Seoul, Singapore, Taipei

2 DETAFOW Type F Gas Purge Type Meter Body (for measurement of gas containing dust and mist) Item Description Body style Wafer Flange Nominal size (mm) 50, 80, 100, , 250, 300, (350) 400, (450), 500 Material Flange rating Body SUS304 STPG370 SUS304TP STPY400 SUS304TP Flanges SS400 or SFVC2A SUSF304 SFVC2A SUSF304 Bluff body SUS304 SCS13A or SUS304 Companion flange JIS10K, ASME/JPI150 JIS10K, ASME/JPI150 Standard connecting pipe Sch40 Sch20 Operating temp. range 20 to to to to to +130 Max. operating pressure Accuracy ess than 1MPa Within ±1% of RD or ±1% of FS Repeatability Within ±0.2% Installation Purge gas Purge rate Purge connection Converter Model Configuration Power source Item Horizontal or vertical Instrumentation air, nitrogen, or the same gas as the metered fluid 0.5/min to 1.0/min at 19.6 to 29.4kPa Rc1/4 fitting provided Description PA21 converter Separately mounted 24 to 32VDC Power consumption 32V 40mA or less (24V 54mA or less) ( 1) Ambient temperature Finish IP rating Transmission length Output signal Explosionproof configuration Cable connection Installation Display Non-explosionproof Explosionproof Sensor to converter Converter to receiving instrument Converter 20 to +60 (no condensation) 20 to +55 (no condensation) Body: Munsell 10B8/4, Cover: Munsell 2.5PB4/10 IP67 Exclusive 5-wire cable Max. 30m (Finished cable O.D.: 10.7 ± 0.5mm) For pulse output: 3-wire shielded cable max. 1km (See NOTE.) For pulse and status output: 4-wire shielded cable max. 1km (See NOTE.) CEVS, CVVS equivalent (Finished cable O.D.: 10.1 to 13mm) 1 Pulse output: Open drain (equivalent to open collector) Max. applied voltage: 30VDC, Allowable current: 50mA Unfactored pulse Pulse width: 0.2msec or 1msec 2 Status output: Open drain (equivalent to open collector) Max. applied voltage: 30VDC, Allowable current: 50mA Select from: Error, Error+Alarm, H/ alarm, Error+H/ alarm Ex d e ⅡC T6 Sensor Amplifier part: Ex d [ib] ⅡC T4, Sensor part: Ex ib ⅡC T4, Applicable temp. range: -20 to +72 Converter Sensor G3/4 (internal thread) G1/2 (internal thread) Explosionproof model: Union clamp of the accompanying pressure-tight packing G3/4 (internal thread) Mounted on 2" pipe stanchion (clamp and U-bolts furnished) CD display % flow rate, error, alarm NOTE: If the wire length exceeds 250m or the cable of less than 1.25mm 2 is used, the resistance of the cable connecting the receiving instrument and the converter must satisfy the following conditions considering voltage drop: 1 ow level of pulse output must satisfy the input condition of the receiving instrument: ow level of pulse output = (If+2Ip+Is) R Voltage between POWER and COMMON of the converter is within the rated voltage: Converter voltage (between POWER and COMMON) = V (2If+Ip+Is) R Where: Ip Maximum current of pulse output in actual use V Supply voltage Is Maximum current of status output in actual use If Maximum current consumption of the flowmeter R Cable resistance between receiving instrument and converter ( 1) To use the power supply other than manufactured by OVA, make sure its voltage capacity is 100mA or more considering the current when the power supply is turned ON. Explosionproof applied temperature range (for explosionproof models) Explosionproof applied temperature range of the instrument is -20 to +72 at the part indicated below. To satisfy the requirements, make sure to use the instrument within the suggested range of fluid and ambient temperature shown below. The part subject to explosionproof Ambient temperature ( ) Ambient temperature derating Fluid temperature ( ) NOTE: Applicable ambient temperature range may vary with the lagging condition of the piping. 2

3 DETAFOW Type F FOW RANGES The DETAFOW Type F measures actual frow rate (m 3 /h[actual]) under pressure. If flow rate information is given under the standard conditions (0 C, 1 atmospheric pressure) (m 3 /h[normal]), it must be converted into an actual flow rate before you refer to the flow range table below. Table A Table B Nom. size mm 20 ( 3 /4 ) 25 (1 ) 32 (1 1 /4 ) 40 (1 1 /2 ) 50 (2 ) 80 (3 ) 100 (4 ) 150 (6 ) 200 (8 ) 250 (10 ) 300 (12 ) 400 (16 ) 500 (20 ) Accuracy Sp. weight kg/m 3 Minimum flow rate m 3 /h [actual] ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale ±1% of reading ±1% of full scale Type of Gas Sp. weight kg/nm 3 Pressure of Gas MPa (gauge) Temperature 20 C Acetylene Argon Carbon Monoxide Ethane Ethylene Air Oxygen Hydrogen Carbon Dioxide Nitrogen City Gas Natural Gas Propane Butane Methane NOTES: 1. ranges listed in above table is calculated based on temperature 20 and viscosity 0.017mPa s. 2. If it is necessary to determine the minimum flow rate precisely, contact OVA. Max. rate m 3 /h Find the value closest to the pressure of gas to be used (lower value) in Table B and determine the minimum flow rate in Table A. How to Determine Minimum Rate Example 1 A 200mm (8 ) size meter is to be used for air having a pressure of 0.74MPa [gauge] at 20. Find the minimum flow rate. [Solution] Finding the minimum flow rate for nominal size 200mm (8 ) in Table A corresponding to 0.74MPa [gauge] air in Table B, we obtain: where accuracy is ±1% of reading: 94.5m 3 /h, where accuracy is ±1% of full scale: 51m 3 /h. Example 2 A 250mm (10 ) size meter is to be used for city gas having a pressure of 0.5MPa [gauge] at 20 with an accuracy of ±1% of reading. Find the minimum flow rate. [Solution] Finding the minimum flow rate for nominal size 250mm (10 ) in Table A corresponding to 0.305MPa [gauge] and 0.577MPa [gauge] of city gas in Table B are 191m 3 /h and 161m 3 /h, respectively. Hence, at 0.5MPa [gauge] we obtain from the rule of proportion: Qmin= ( ) 170m 3 /h Example 3 A 200mm (8 ) size meter is to be used for butane gas having a pressure of 0.301MPa [gauge] at 80 C with an accuracy of 1% of reading. Find the minimum flow rate. [Solution] Although the minimum flow rate in Table A corresponding to 0.301MPa [gauge] is 94.5m 3 /h, the minimum flow rate should increase by the amount of decrease in specific weight due to elevated temperature (80 ) as follows: Sp. weight of butane at 80 = =8.3kg/m The minimum flow rates for the nominal size 200mm (8") corresponding to specific weights 7kg/m 3 and 10kg/m 3 in Table A are 107m 3 /h and 94.5m 3 /h, respectively. Hence, the minimum flow rate of butane at 80 (sp. weight 8.3kg/m 3 ) can be obtained from the rule of proportion: Qmin= ( ) 102m 3 /h

4 DETAFOW Type F PERFORMANCE CHARACTERISTICS Pressure oss Nominal sizes 20 to 32mm Nominal sizes 50 to 500mm 50 Pres. loss Coeff. [C] Pres. loss Coeff. [C] rate Qm 3 /h [actual] rate Qm 3 /h [actual] ΔP= C γ 100 ΔP: Pressure loss (kpa) γ: Sp. weight (kg/m 3 ) To find the pressure loss, read the coefficient C at the intersection of the flow rate Q and the diagonal line of the particular size and determine ΔP by the equation above. Meter Factors The table below shows the nominal meter factor by each nominal size and pulse frequency at maximum flow rate. Nominal Size mm (inch) Nominal Meter Factor /P Pulse Freq. at Max. rate Hz Max. rate m 3 /h 20 ( 3 / 4 ) (1) (1 1 / 4 ) (2) (3) (4) (6) (8) (10) (12) (16) (20)

5 DETAFOW Type F OUTINE DIMENSIONS (Standard type) (Unit in mm) Wafer type 20mm (3/4 ) Wafer type 25mm (1 ) to 150mm (6 ) Conduit Connection G1/ Conduit Connection G1/2 φd φd φd H H φ103 φ103 φd φd φd Dimensions D and H depend on the connecting flange rating. Flange type 200mm (8 ) to 500mm (20 ) Conduit Connection G1/2 H φ103 Style Wafer type Flange type Nominal size mm (inch) Flange rating H d D Approx. Weight kg 20 (3/4) (1) Companion Flange (1 1/4) JIS 20 K 50 (2) JIS 30 K 80 (3) ASME/JPI (4) ASME/JPI (6) (8) 250 (10) 300 (12) 400 (16) 500 (20) JIS 20 K JIS 30 K ASME/JPI ASME/JPI JIS 20 K JIS 30 K ASME/JPI ASME/JPI JIS 20 K JIS 30 K ASME/JPI ASME/JPI ASME/JPI ASME/JPI NOTE: Outline dimensions of special or regulation-compliant products may be different. Please refer to the approval drawing or delivery specification. 5

6 DETAFOW Type F OUTINE DIMENSIONS (Gas purge type) (Unit in mm) Wafer type 50mm (2 ) to 150mm (6 ) Flange type 200mm (8 ) to 500mm (20 ) Conduit Connection G1/ Conduit Connection G1/2 φ103 Purge gas Connection H Purge gas Connection φd φd φd φd H φ103 Style Wafer type Flange type Nominal size mm (inch) Flange rating H d D Approx. Weight kg 50 (2) (3) Companion Flange (4) ASME/JPI (6) (8) 250 (10) 300 (12) 400 (16) 500 (20) ASME/JPI ASME/JPI ASME/JPI ASME/JPI ASME/JPI NOTE: Outline dimensions of special or regulation-compliant products may be different. Please refer to the approval drawing or delivery specification. 1 Purge Box (FB0 2 ) Unit in mm Mist Separator Reducing Valve 570 Rotameter 210 Pipe 492 Purge Inlet Purge Outlet (to meter) Enclosure: Sheet steel Finish: ight beige (5Y7/1) Approx. weight: 4 kg 6

7 DETAFOW Type F Converter (PA21) Unit in mm φ Conduit Connection G3/4 Conduit Connection G3/4 71 WIRING DIAGRAM (1) Wiring for converter power source and output Do not use this conduit connection. Terminal Cover for Maintenance Terminal label and description abel Description Remark POWER 24 to 32VDC STATUS PUSE COMMON EARTH DC power 24 to 32VDC Status output (open drain) Pulse output (open drain) DC power (0V) Status output ( ) Pulse output ( ) Grounding Open drain output (equivalent of open collector output) can be connected up to 30V, 50mA. Do not use the conduit connection on the terminal cover side. For wiring connection specification, refer to general specifications "Converter" on Page 2. 7

8 OVA MODE E4000 DETAFOW Type F (2) Wiring between converter and sensor Converter (PA21) SIG 0V SUP C1 C2 SHIED SHIED C2 C1 SUP 0V SIG Sensor terminal box Sensor terminal box must be installed using intrinsically safe installation procedure. Terminal label and connecting cable color Converter terminals Terminals inside sensor terminal box Connecting cable color SIG SIG White 0V 0V Black SUP SUP Red C1 C1 Green C2 C2 Yellow SHIED SHIED Exclusive cable must be used for connecting the converter and the sensor. Either the left or right conduit connection (cable entry) of the sensor terminal box can be used. For wiring connection specification, refer to general specifications "Converter" on Page 2. Twist [Red/Black/White], [Yellow/Green], and shielded cables together and cover the bundle with the accompanying tube, then connect to SHIED terminal. CONNECTION TO RECEIVING INSTRUMENTS (EXAMPE) ine temperature and pressure are considered approximately constant and correction factor can be multiplied as constant: Meter body Converter Pulse Distributor (SU1508) or External Power Source ( 2) Totalizer (E0122) Total and Instantaneous rate Readout ine temperature and pressure are automatically compensated, and total and instantaneous flow readout (or output) are obtained: Meter body Converter 4 to 20mADC Pressure Transmitter Computer (E4001 series) Unfactored Pulse Factored Pulse Resistance Thermometer For details of individual receiving instruments, refer to respective general specification sheets. 1: A digital filter (SU1301) cannot be connected. (The converter is equipped with the equivalent function.) 2: Separate power source is required when connecting with the totalizer (E0122). 8

9 DETAFOW Type F INSTAATION CONDITIONS 1. Typical Piping Instructions It is required that the flow pattern of the fluid flowing in and out of a vortex flowmeter be as uniform as possible for accurate metering performance. Therefore, proper flow straightening measures have to be applied when installing a vortex flowmeter. The standard piping instructions are shown in the following table. (1) Use an OVA flow straightener or provide a specified straight pipe (ISO-5167 compliant). No. Piping Arrangement Straight Pipe ength () Remark 1 OVA's - Straightener Honey Vane Straightener 8D 12D Refer to P11 Refer to GS/GCF001 Applicable to Nominal size 25mm or above 2 Reducer 15D Min. A concentric reducer is installed at the upstream of a meter. 23D Min. An elbow is installed at the upstream of a meter. 3 Elbow 25D Min. Two elbows are installed at the upstream of a meter. 40D Min. Two elbows are vertically installed at the upstream of a meter. 4 Fully open gate valve Fully Open 15D Min. A full-open gate valve is installed at the upstream of a meter. 5 Partially open gate valve Partially Open 50D Min. A partially open gate valve, sharp orifice or something that markedly disturbs the flow pattern is upstream of meter. NOTES: 1: Upstream and downstream pipes adjacent to the flowmeter should be of the same internal diameter (ID) as the flowmeter. (The exclusive flow straightener, Honey Vane, and downstream short pipe have the same ID as the flowmeter.) The table below shows the standard ID of the flowmeter. Confirm the delivery specification in case ID is non-standard. meter standard ID Nominal size under 400mm 400mm or more ID reference Sch40 Sch20 2: A short pipe section, 5D or longer shall be provided downstream of the meter. 3: For pressure detection, provide the probe downstream of the flowmeter (see the right figure). To avoid disturbances in the flow, temperature detection should be made downstream of the flowmeter and, at the same time, upstream of the control valve. FOW 2 to 7D from the meter Min. 2D from flowmeter Pressure detection point D: Nominal size Temperature detection point Min. 1D from pressure detection point 2. Pressure Pulsation In case the flowmeter is installed in the line where instruments that can generate pressure pulsation, such as roots blower or compressor is present, performance of the flowmeter can be affected by flow pulsation. Allowable pulsation pressure is calculated from the following equation: N< 22ρV 2 (Pa) where, N: Pulsation pressure (Pa) ρ: Density (kg/m 3 ) V: Min. Velocity (m/s) Even at shutdown, pressure pulsation in the process fluid can produce a false output. If pressure pulsation is excessive, take the following measures: 1 ocate the source of flow pulsation downstream of the flowmeter. 2 Install a pulsation attenuator. 3 At shutdown of the flow, shut off valves upstream and downstream of the flowmeter. 9

10 DETAFOW Type F Installation of Honey Vane S 1 ocate the Honey Vane S upstream of the flowmeter. 2 Provide a short pipe (8D or longer) between Honey Vane S and flowmeter. 3 Regarding the bolts and nuts used for connecting JPI flange, adopt unified screw threads. If it is necessary to use metric screw threads, contact OVA. meter Honey Vane S FOW Min. 8D Honey Vane Outline Dimensions Nominal size (mm) Honey Vane S Honey Vane φd * (mm) t (mm) (mm) * Dimensions for JIS 10K. t φd Honey Vane S t Honey Vane PRECAUTIONS ON USE 1. This flowmeter is developed, designed, and manufactured to be used as a flowmeter for general industrial application. Therefore, when it is used for the application where its operation is directly related to the safety of the relevant system or the product is important in the facilities (such as process control and custody transfer), you are requested to ensure sufficient security including safety design, redundancy and duplication of the process, and implementation of periodic inspection. Do not use this flowmeter where its operation and performance directly affect human life. 2. When used under appropriate conditions, this flowmeter can demonstrate its stable performance without aging degradation of accuracy. However, malfunction or failure may occur due to various factors. Thus, examining the operating conditions, operating status, and importance in the process, you should consider periodic maintenance of your flowmeter. In order to secure long-term and safe use, OVA recommends the customer to verify the soundness of the flowmeter through periodic inspection every two years. For the details of inspection, contact the nearest OVA sales/service office or representatives. 3. This flowmeter is manufactured, adjusted, and inspected to meet the conditions of use. The fluid measured, flow range, pressure, temperature, etc., must be applied under the specified conditions. The conditions for use are stated on the nameplate attached on the flowmeter transmitter and specification sheet supplied with the product. 4. The materials used in this flowmeter are stated in this document or delivery specification sheet shipped with the equipment. Supplied with all the necessary information by the customer, OVA has selected materials that best suit the customer requirements including corrosion resistance. However, we ask you to understand that the final judgment on the compatibility of the materials in the actual process environment lies with the customer. 10

11 DETAFOW Type F PRODUCT CODE EXPANATION Main code Converter (Power supply) Regulations Explosion-proof Process connection Major Parts Material Temp. category Fluid category Nominal Size Model Model V F W DETAFOW Type F Wafer type (Nominal Size: 20 to 150mm) V F Y DETAFOW Type F Wafer type, spigot joint type (Nominal Size: 25 to 150mm) V F F DETAFOW Type F Flanged type (Nominal Size: 200 to 500mm) Nominal Size mm (3/4 ) mm (1 ) mm (1 1/4 ) mm (1 1/2 ) (Designed on PO issued) mm (2 ) mm (3 ) mm (4 ) mm (6 ) mm (8 ) mm (10 ) mm (12 ) mm (14 ) (Designed on PO issued) mm (16 ) mm (18 ) (Designed on PO issued) mm (20 ) 7 8 Fluid category G Gas 9 Temp. category 0 Standard Max. fluid temperature: Major Parts Material D SUS304 or SUS304 equivalent Allowed lowest temp.: -20 (Nominal Size: 20 to 500mm) G Carbon steel (STPG370/SFVC2A/SS400) Allowed lowest temp.: 0 (Nominal Size: 200 to 500mm) Z Special Process connection 1 J 0 JIS10K FF J 1 JIS10K RF For wafer type FF is also available J B JIS16K RF For wafer type FF is also available J 2 JIS20K RF For wafer type FF is also available J 3 JIS30K RF For wafer type FF is also available P 1 JPI150 RF For wafer type FF is also available P 3 JPI300 RF For wafer type FF is also available P 6 JPI600 RF (Designed on PO issued) A 1 ASME150 RF For wafer type FF is also available A 3 ASME300 RF For wafer type FF is also available A 6 ASME600 RF (Designed on PO issued) Z 9 Special Explosion-proof 0 0 Non-explosionproof J 4 TIIS sensor: T4 (transmitter: T6) 2 Main code 16 Regulations 0 Standard No applicable law and regulations G H High Pressure Gas Safety Act (Approved product) High Pressure Gas Safety Act (Individual test) Gas Business Act (Approved product) w/material test certificate w/material test certificate (Designed on PO issued) w/material test certificate (Designed on PO issued) M Gas Business Act w/material test certificate Q Electricity Business Act (Certificate required) w/material test certificate (Designed on PO issued) R Electricity Business Act w/material test certificate T Fire Service Act w/material test certificate F 17 w/material test certificate 18 Converter (Power supply) 5 PA21 External power supply (24 to 32VDC) 9 Special 19 Converter configuration 2 Separately mounted 20 Display 0 Digital indicator (% instantaneous flow indication) Pulse G Open drain pulse Communication interface N Always "N" Version code A Version code: A Sensor configuration 1 External sensor Sensor type 1 Standard (Nominal Size: 20 to 500mm) 2 Gas-purge (Nominal Size: 50 to 500mm) Max. operating pressure: 1MPa at max. 3 Gas-purge (For low temp. or high temp.) (Designed on PO issued) 4 Double sensor (Designed on PO issued) 5 Double sensor w/magnet filter (Designed on PO issued) 9 Special Accompanied cable length 0 10m (Standard) 9 Specific cable length (Max. 30m) Special 0 Standard 1: Flange face to fit with the gasket is RF. Flange serration according to ASME standard complies with ASME B : Make sure to use the dedicated expplosionproof cable gland which supplied with the flowmeter. Z Converter configuration Display Pulse Communication interface Version code Sensor configuration Sensor type Accompanied cable length Special / / / Additional code When "Special" or "Designed on PO issued" is chosen 11

12 DETAFOW Type F PRODUCT CODE EXPANATION Converter (Power supply) Regulations Explosion-proof Process connection Major Parts Material Temp. category Fluid category Nominal Size Model Main code Converter configuration Display Pulse Communication interface Version code Sensor configuration Sensor type Accompanied cable length Special / / / Additional code Additional code Category of High Pressure Gas H P 0 Other than High Pressure Gas H P 1 Toxic gas and flammable gas H P 2 Toxic gas H P 3 Flammable gas H P 4 Other than toxic or flammable gas Accuracy F 1 0 ±1.00% RD F 1 0 ±1.00% FS Special test (instrumental error) A 0 1 Actual flow test B (Certificate) Witnessed accuracy test not applicable A 0 3 Actual flow test A (Report) Witnessed accuracy test applicable A 1 0 Taxed custody transfer A 2 0 By certified measurer A 9 9 Designation of instrumental error test method Direction of sensor terminal box F 1 F 2 F 3 F 4 Designation of test point and/or addition, etc. direction and entry of electric conduit are in vertical, with the long lid on flow inlet side. Direction of flow and entry of electric conduit is same, with the long lid is in front when R direction and entry of electric conduit are in vertical, with the long lid on flow outlet side. Direction of flow and entry of electric conduit is same, with the long lid is behind when R Designated special paint on body B C 0 Corrosion proof B A 0 Salinity and acid tolerance imited to 120 and lower B X 0 Customer designation Designated special paint on transmitter S F 0 Corrosion proof Special S D 0 Salinity tolerance S E 0 Acid tolerance Special S X 0 Customer designated paint Special Cleansing T W 0 Non-oil and non-water treatment 1: Need not choose the item when required to implement in Japan law and regulation. Only for items other than the legal requirement, customer can choose as special requirement. Document D S J DWG and specifications for approval (Japanese) D S E DWG and specifications for approval (English) D R 0 Re-submission of DWG with specifications D C J Final DWG (Japanese) D C E Final DWG (English) D P J Calculation sheet (Japanese) D P E Calculation sheet (English) Unavailable for the Japan law compliant S E J Instrumental error test report (Japanese) S E E Instrumental error test report (English) S T J Pressure test report (Japanese) S T E Pressure test report (English) S A J Airtight test report (Japanese) S A E Airtight test report (English) D D J Dimensional check record (Japanese) D D E Dimensional check record (English) S P J Penetrant test report (Japanese) Welded part of pressure resistant vessel S P E Penetrant test report (English) Welded part of pressure resistant vessel S M J Magnetic particle inspection (Japanese) Welded part of pressure resistant vessel S M E Magnetic particle inspection (English) Welded part of pressure resistant vessel S R J Radiographic inspection (Japanese) Welded part of pressure resistant vessel S R E Radiographic inspection (English) Welded part of pressure resistant vessel S U J Ultrasonic inspection (Japanese) Welded part of pressure resistant vessel S U E Ultrasonic inspection (English) Welded part of pressure resistant vessel S X J PMI test report (Japanese) S X E PMI test report (English) S S J Impact test report (Japanese) S S E Impact test report (English) D Y J WPS/PQR (Japanese) D Y E WPS/PQR (English) D 9 J Photo (Japanese) D 9 E Photo (English) D T J Inspection procedure (Japanese) D T E Inspection procedure (English) C A J Inspection certificate: A set Only Japanese C B J Inspection certificate: B set Only Japanese C C J Inspection certificate: C set Only Japanese C D J Inspection certificate: D set Only Japanese Witnessed by customer V 1 0 Required 12

13 DETAFOW Type F 13

14 DETAFOW Type F PEASE SUPPY THE FOOWING INFORMATION WHEN YOU INQUIRE. Fill in the blanks. Tick the boxes that apply. Item Description 1. Name of gas 2. Application 3. range Max. Normal Min. m 3 /h [normal] m 3 /h [actual] 4. Temperature range Max. Normal Min. 5. Pressure range Max. Normal Min. MPa [gauge] 6. Compensation reference Temperature ref. Pressure ref. MPa [gauge] 7. Compression coefficient Z Z0 8. Density or specific gravity Density kg/m 3 [normal] kg/m 3 [actual] Specific gravity (Air=I) 9. Viscosity Viscosity mpa s mm 2 /s at 10. Connections 11. straightening pipe Nominal size mm inch, Flange rating JIS K RF ASME RF Sch FF JPI RF Required ( straightener, Honey Vane S, Honey Vane, and downstream short pipe) Not required (Please supply straight pipe of appropriate length, ID, and Sch No.) 12. Compensation range Temperature: to, Pressure: to MPa [gauge] 13. Accuracy test Required Not required 14. Receiving instrument Specify the model and specification referring to P.8 "CONNECTION TO RECEIVING INSTRUMENTS" on P Compensation Not required 16. Explosionproof Required Not required 17. Regulations Required Not required 18. Cable length Standard 10m Specific length m 19. Other considerations The specification as of April, 2017 is stated in this GS Sheet. Specifications and design are subject to change without notice. Sales Representative: GS.No.GBD110E 初版改訂印刷