IE073: Intrinsic Safety, Galvanic Isolation and Zener Barriers Technology & Applications
|
|
- Annabelle Hubbard
- 6 years ago
- Views:
Transcription
1 IE073: Intrinsic Safety, Galvanic Isolation and Zener Barriers Technology & Applications IE073 Rev.001 CMCT COURSE OUTLINE Page 1 of 5
2 Training Description: The hazardous-area circuits 'float' i.e. is not referenced to earth via the interface unit. This allows the user to take advantage of the inherent earth fault rejection, possibly reinforced with an earth leakage detector (no-fail), or alternatively, by earthing the circuit at one point, the user can produce a preferred mode of failure (fail-safe). The isolation of the hazardous area, safe area and power supply circuits from each other leads to a high degree of operational flexibility, and reduces any interaction between earths on the circuits, and removes the need for a detailed knowledge of the internal circuits of the safe area apparatus. Intrinsic safety is a technique for ensuring that the electrical energy available in a circuit is too low to ignite the most easily ignitable mixture of gas and air. The ignition mechanisms considered are electrical, by spark energy, and thermal, by hot surfaces. The design of the circuit and equipment is intended to ensure safety both in normal use and in all probable fault conditions. Among the faults considered is the possibility of unacceptable power being fed through from the safe-area apparatus. Consequently, intrinsic safety is essentially a system concept in which the apparatus in the hazardous area, the apparatus in the safe area. And the combination of these two must all be considered. Training Objective: By the end of the training, participants will be able to: Explain the classifications of the hazard plant and equipment Understand the hazard area classification in IEC/European countries Understand the obligations required in operating hazard plant Describe the Intrinsically Safe system principle, components, categories and applications. Understand what a ground loop is Understand the principle and application of safety barriers Understand the principle and application of Galvanic Isolators Compare between safety barriers and galvanic isolators Identify the suitable barriers for different applications Verify the safety and operational compatibility Check the suitable isolator specification for particular application Select suitable safety interface for smart electrical devices. Install the Intrinsic all safe barriers according to UK code of practices Identify is earthing cable specification for IS Installation. Find IS faults and repair it Training Designed for: This course is intended for all Instrumentation and Control Engineers & Technicians, Electrical Engineers & Technicians, Projects Engineers & Technicians, Computers and IT Engineers and Technical Supervisory Personnel involved in intrinsic safety, galvanic isolation and Zener barriers technology & applications. IE073 Rev.001 CMCT COURSE OUTLINE Page 2 of 5
3 Training Program: DAY ONE: PRE-TEST Introduction Intrinsic Safety Who's who in intrinsic safety Classification of hazardous areas Apparatus or gas grouping Temperature classification Methods of protection for equipment used in hazardous areas Ingress protection (IP) system for enclosures Dust hazards Earthing and bonding Connection of intrinsically safe equipment to various types of mains supply Intrinsically safe systems DAY TWO: Intrinsic Safety (Continuation) Hazardous-area apparatus Hazardous-area cables and accessories Safe-area equipment Documentation and administration Inspection Fault-finding and repairs Legal requirements DAY THREE: Galvanic isolation Power supplies Enclosures and areas of use Switch/proximity detector interface units Intrinsically safe output, switch-operated relay DAY FOUR: Galvanic isolation (Continuation) Earth leakage detector Solenoid/alarm drivers Trip amplifiers Analogue-signal interface units High-frequency digital interface units IE073 Rev.001 CMCT COURSE OUTLINE Page 3 of 5
4 DAY FIVE: Zener Barriers Barriers components Barriers types The mounting and mechanics of barriers Choosing a barrier system Thermocouples Alternating-current sensors and signals Resistance thermometers Strain-gauge bridges and potentiometers Transmitters Switches and proximity detectors Controller outputs Solenoids, alarms, LEDs Course Conclusion POST-TEST and EVALUATION Training Requirement: Hand s on practical sessions, equipment and software will be applied during the course if required and as per the client s request. Training Methodology: This interactive training course includes the following training methodologies as a percentage of the total tuition hours:- 30% Lectures, Concepts, Role Play 30% Workshops & Work Presentations, Techniques 20% Based on Case Studies & Practical Exercises 20% Videos, Software & General Discussions Pre and Post Test Training Certificate(s): Internationally recognized certificate(s) will be issued to each participant who completed the course. Training Fees: As per the course location - This rate includes participant s manual, hand-outs, buffet lunch, coffee/tea on arrival, morning & afternoon of each day. IE073 Rev.001 CMCT COURSE OUTLINE Page 4 of 5
5 Training Timings: Daily Timings: 07:45-08:00 Morning Coffee / Tea 08:00-10:00 First Session 10:00-10:20 Recess (Coffee/Tea/Snacks) 10:20-12:20 Second Session 12:20-13:30 Recess (Prayer Break & Lunch) 13:30-15:00 Last Session For training registrations or in-house enquiries, please contact: Aisha Relativo: aisha@cmc-me.com Tel.: or Mob.: Training & Career Development Department IE073 Rev.001 CMCT COURSE OUTLINE Page 5 of 5
IE098: Advanced Process Control for Engineers and Technicians
IE098: Advanced Process Control for Engineers and Technicians IE098 Rev.001 CMCT COURSE OUTLINE Page 1 of 6 Training Description: Advanced Process Control and Loop Tuning and Analysis is designed to provide
More informationMU043D: Mechanical Seals
MU043D: Mechanical Seals Jun 26 28, 2018 / Dubai MU043 Rev.001 CMCT COURSE OUTLINE Page 1 of 5 Training Description: This is an intensive, highly practical and useful five-day course. The participant will
More informationMU102: Mechanical Seals Applications for Rotating Machinery
MU102: Mechanical Seals Applications for Rotating Machinery MU102 Rev.001 CMCT COURSE OUTLINE Page 1 of 5 Training Description: All Rotating Equipment Machinery require controlling of the pumped fluids
More informationT e l N o : F a x N o : E m a i l : a i s h c m c - m e. c o m w w w. c m c - m e.
MU047: Practical Valve Technology: Selection, Installation, Upgrading, Inspection & Troubleshooting MU047 Rev.002 CMCT COURSE OUTLINE Page 1 of 7 Training Description: This five-day intensive course covers
More informationPE096: Overview of Gas Processing Technology
PE096: Overview of Gas Processing Technology PE096 Rev.001 CMCT COURSE OUTLINE Page 1 of 6 Training Description: This course is designed for a broad audience and is participative and interactive, utilizing
More informationIE039: Practical Process Instrumentation & Automatic Control
IE039: Practical Process Instrumentation & Automatic Control IE039 Rev.001 CMCT COURSE OUTLINE Page 1 of 8 Training Description: Process Control & Instrumentation is becoming an increasingly important
More informationIE011: Process Control & Instrumentation Technology
IE011: Process Control & Instrumentation Technology IE011 Rev.001 CMCT COURSE OUTLINE Page 1 of 8 Training Description: This intensive course covers fundamental and practical of instrumentation measurements
More informationIE068: Process Instrumentation Technology
IE068: Process Instrumentation Technology IE068 Rev.002 CMCT COURSE OUTLINE Page 1 of 8 Training Description: This course covers fundamental and practical of instrumentation measurements including Flow
More informationPE094: Applied Heat Transfer Equipment and Thermal Design in the Process Industry
PE094: Applied Heat Transfer Equipment and Thermal Design in the Process Industry PE094 Rev.001 CMCT COURSE OUTLINE Page 1 of 6 Training Description: To provide practical and applied knowledge relating
More informationHSE246 Confined Space Safety
HSE246 Confined Space Safety H.H. Sheik Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E www.ictd.ae ictd@ictd.ae Course Introduction: This Confined Space Safety course will allow the entrant, attendant,
More informationHSE159 Safe Work Practices for Confined Space Entry
HSE159 Safe Work Practices for Confined Space Entry H.H. Sheik Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E www.ictd.ae ictd@ictd.ae Course Introduction: The hazards of confined spaces are not
More informationExplosion Protection Technology Pty Ltd
How to Apply Hazardous Area Australian Standards (Group II) 3-Day On-Site Workshop * 2018 This workshop provides a sound understanding of electrical compliance and your responsibilities in Group II hazardous
More informationIntrinsic safety 101 hazardous locations
Intrinsic safety 101 hazardous locations Protection methods, containment, segregation, and prevention By Robert Schosker This article answers the question, Why worry about hazardous locations? The area
More information1.8 INDUSTRIAL PROCESS WEIGHING IN HAZARDOUS AREAS
1.8 INDUSTRIAL PROCESS WEIGHING IN HAZARDOUS AREAS EXPLOSION PROTECTION In addition to the type approval and certification of industrial weighing systems concerned with accuracy, equipment that is also
More informationTraining Fees 3,400 US$ per participant for Public Training includes Materials/Handouts, tea/coffee breaks, refreshments & Buffet Lunch.
Training Title DISTRIBUTED CONTROL SYSTEMS (DCS) 5 days Training Venue and Dates DISTRIBUTED CONTROL SYSTEMS (DCS) Trainings will be conducted in any of the 5 star hotels. 5 22-26 Oct. 2017 $3400 Dubai,
More informationExplosion Protection Technology Pty Ltd
RRRHazardous Area Australian Standards Simplified 2-Day Workshop * Tuesday 24 - Wednesday 25 July 2018 This workshop provides an introduction to electrical compliance and your responsibilities in Group
More informationTechnical Data. Dimensions
0102 Model Number Features Comfort series 15 mm flush Accessories MHW 01 Modular mounting bracket MH 04-2057B Mounting aid for VariKont and +U1+ V1-G-N-2M-PUR Female cordset, M12, 2-pin, NAMUR, PUR cable
More informationMOE101 HLO & Offshore Helideck Safety
MOE101 HLO & Offshore Helideck Safety H.H. Sheikh Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E www.ictd.ae ictd@ictd.ae Course Introduction: Helicopters play a major role in the offshore environment.
More informationInstruction Manual Differential Pressure Transmitter
DE61 Instruction Manual Differential Pressure Transmitter Table of Contents 1. Safety Instructions 2. Intended Applications 3. Product Description and Functions 4. Installation 5. Commissioning 6. Maintenance
More informationTechnical Data. Dimensions
00 Model Number Features Comfort series 30 mm non-flush Accessories MHW 0 Modular mounting bracket V-G Female connector, M, 4-pin, field attachable V-W-N-M-PUR Female cordset, M, -pin, NAMUR, PUR cable
More informationC&G 2395 Exam Paper April Section A - All questions carry equal marks. Answer all three questions. Show all calculations.
C&G 2395 Exam Paper April 2013 Section A - All questions carry equal marks. Answer all three questions. Show all calculations. Q.1 The electrical installation in a small food retail outlet is scheduled
More informationDE149. Wireline Servicing, Fishing Job for Completion and Workover
DE149 Wireline Servicing, Fishing Job for Completion and Workover H.H. Sheik Sultan Tower (0) Floor Corniche Street Abu Dhabi U.A.E www.ictd.ae ictd@ictd.ae Course Introduction: This five-day course is
More informationTechnical Data. Dimensions
0102 Model Number Features Comfort series 5 mm flush Usable up to SIL 2 acc. to IEC 61508 Accessories BF 18 Mounting flange, 18 mm EXG-18 Quick mounting bracket with dead stop Technical Data specifications
More informationElectrical Equipment for Hazardous Areas GNEM1
Electrical Equipment for Hazardous Areas GNEM1 This module should be designed to develop the candidate s skills and knowledge on the operating procedures and techniques for working on electrical apparatus
More informationTechnical Data. Dimensions
0102 Model Number Features Comfort series 15 mm non-flush Stainless steel housing Accessories BF 30 Mounting flange, 30 mm Technical Data specifications Switching element function NAMUR, NC Rated operating
More informationSuitable for anyone who is required to maintain industrial pneumatic systems. No prior knowledge of pneumatic or electrical principles is necessary.
PNEUMATICS COURSE 660: 4 DAYS: Max 8 Candidates This course provides maintenance personnel and production operators etc with the skills and knowledge necessary to carry out maintenance tasks on pneumatic
More informationTechnical Data. General specifications Switching element function Rated operating distance s n 5 mm
00 Model Number Features 5 mm flush Usable up to SIL acc. to IEC 6508 Accessories V-G Female connector, M, -pin, field attachable V-W Female connector, M, -pin, field attachable V-G-N-M-PUR Female cordset,
More informationBA307C & BA308C Intrinsically safe loop-powered 3½ digit panel mounting indicators issue 9
BA307C & BA308C Intrinsically safe loop-powered 3½ digit panel mounting indicators issue 9 Issue: 9 22 nd March 2013 2 CONTENTS 1. Description 2. Operation 3. Intrinsic Safety Certification 3.1 ATEX certificate
More informationDimensions. Technical Data General specifications Switching element function Rated operating distance s n 5 mm
Dimensions M18x1 37 40 4 0102 24 LED Model Number Features 5 mm embeddable Usable up to SIL2 acc. to IEC 61508 Connection BN BU Accessories L+ L- EXG-18 Quick mounting bracket with dead stop BF 18 Mounting
More informationMeasurement And Control Appreciation
Measurement And Control Appreciation Course Content Aim To provide an appreciation of the operation and application of process plant instrumentation used for the measurement and display of the main process
More informationLPG, LEG, LNG tankers & Chemical and Product tankers
marine Welcome to Nordan Marine A/S Nordan Marine Calibration Service: LPG, LEG, LNG tankers & Chemical and Product tankers Calibration of level controls Calibration of pressure and temperature alarms
More informationTechnical Data. General specifications. Rated operating distance s n 5 mm
0102 Model Number Features 5 mm flush Usable up to SIL 2 acc. to IEC 61508 Accessories EXG-18 Quick mounting bracket with dead stop BF 18 Mounting flange, 18 mm Technical Data specifications Switching
More informationEN00 Pre-Instructional Survey
EN00 Pre-Instructional Survey Name: Date: 1. At 433 degrees F, a type J thermocouple with a 3 degree F reference junction will produce an output in millivolts that is most nearly to: a. 9.04 b. 10.51 c.
More informationTechnical Data. General specifications Switching element function Rated operating distance s n 2 mm
0102 Model Number Features 2 mm flush Usable up to SIL 2 acc. to IEC 61508 Accessories EXG-12 Quick mounting bracket with dead stop BF 12 Mounting flange, 12 mm Technical Data specifications Switching
More informationTechnical Explanation
Technical Explanation for ESI Pressure Sensors Technical Explanation What is a pressure transmitter? A pressure transmitter (also called pressure transducer or pressure converter) is a component used to
More informationDimensions. Technical Data General specifications Switching element function Rated operating distance s n 10 mm
Dimensions M30x1,5 5 40 37 0102 Model Number 36 LED Features Comfort series 10 mm embeddable Connection BN BU Accessories BF 30 Mounting flange, 30 mm L+ L- Technical Data specifications Switching element
More informationDimensions. Technical Data General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm
Dimensions 65 GW2 40 35 9 5 GW1 14 11 9 5.4 M20 x 1.5 0102 Model Number S M12 x 1.5 Features 77.5 LED V Direct mounting on standard actuators Compact and stable housing with terminal compartment connection
More informationTechnical Data. Dimensions
00 Model Number Features mm flush Usable up to SIL acc. to IEC 6508 Accessories V-G Female connector, M, -pin, field attachable V-W Female connector, M, -pin, field attachable V-G-N-M-PUR Female cordset,
More informationOSAT Series. Intrinsically Safe Infrared Temperature Sensor Operator's Guide
OSAT Series Intrinsically Safe Infrared Temperature Sensor Operator's Guide Issue L Jan 2017 Introduction OSAT Series intrinsically safe non-contact infrared temperature sensors measure the temperature
More informationHow to specify a product. Process Sensors and Mechanical Instruments
How to specify a product Process Sensors and Mechanical Instruments Keep the overview. Here is some guideline information on how to specify our products. Intended as supplementary help to specification
More informationTechnical Data. Dimensions
0102 Model Number Features 10 mm flush Shielded PUR cable for oil and gas sector Accessories BF 30 Mounting flange, 30 mm Technical Data specifications Switching function Normally closed (NC) Output type
More informationSession One: A Practical Approach to Managing Safety Critical Equipment and Systems in Process Plants
Session One: A Practical Approach to Managing Safety Critical Equipment and Systems in Process Plants Tahir Rafique Lead Electrical and Instruments Engineer: Qenos Botany Site Douglas Lloyd Senior Electrical
More informationSupplementary Operator s Manual 42/24-14 EN Rev. 3
Advance Optima Continuous Gas Analyzers AO2000 Series with Uras26, Magnos206, Caldos25, Caldos27 Designed per Category 3G for Measurement of Flammable Gases ( Safety Concept ) and Non-flammable Gases Supplementary
More informationYokogawa Systems and PCI Training
Yokogawa Systems and PCI Training 09 th December 2014 Nico Marneweck 082 883 2652 Kallie Bodenstein 083 226 2787 Marco Coccioni 072 409 5779-1 - Introduction Training customised for the South Africa Industrial
More informationInductive slot sensor
0102 Model Number Features 3.5 mm slot width Usable up to SIL 3 acc. to IEC 61508 Nonferrous targets Application Danger! In safety-related applications the sensor must be operated with a qualified fail
More informationTechnical Data. General specifications. Rated operating distance s n 2 mm
0102 Model Number Features 2 mm flush Usable up to SIL 2 acc. to IEC 61508 Technical Data specifications Switching function Normally closed (NC) Output type NAMUR Rated operating distance s n 2 mm Installation
More informationUser s Manual EJX/EJA-E Series NEPSI Certification [Option code: /NF2, /NS21, /NS24 and /NS25] IM 01C25A00-12E
User s Manual EJX/EJA-E Series NEPSI Certification [Option code: /NF2, /NS21, /NS24 and /NS25] 12th Edition 1 1. Introduction Thank you for purchasing the DPharp electronic pressure transmitter. This manual
More informationAK100 Series ATEX Compliant Gas Analyzer System for Hydrogen-cooled Alternators
Data sheet DS/AK EN Rev. J AK Series ATEX Compliant Gas Analyzer System for Hydrogen-cooled Alternators Superior technology and quality from the world leader in hydrogen measurement ATEX compliant intrinsically
More informationABB MEASUREMENT & ANALYTICS DATA SHEET. AK100 Series ATEX compliant gas analyzer system for hydrogen-cooled alternators
ABB MEASUREMENT & ANALYTICS DATA SHEET AK100 Series ATEX compliant gas analyzer system for hydrogen-cooled alternators AK100 S E RIE S ATEX COMP LI AN T GAS ANALY ZE R SYSTE M DS/AK100-E N RE V. O Measurement
More informationFLAMMABLE GAS SENSOR/TRANSMITTER
FLAMMABLE GAS SENSOR/TRANSMITTER Plant safety protection for flammable gases. F E A T U R E S Fixed gas monitoring for point source hazards and perimeter protection in arduous duty and exposed locations.
More informationAUTOMATIC GAS MANIFOLDS
AUTOMATIC GAS MANIFOLDS Phoenix Pipeline Products Limited. Unit 8, McKenzie Industrial Park, Tel No.: 44 (0) 161 428 7200 Bird Hall Lane, Fax No.: 44 (0) 161 428 7010 Stockport, Email: info@p3-phoenix.com
More informationPressure Calibrators. Series PC..., PM...
Pressure Calibrators Series PC..., PM... SIKA-Precision Pressure Calibrators, Series PC..., PM... We help you, if you are under pressure! Pneumatic pressure calibrators PM 25 A, PM 25 D, PM 110 PIC pressure
More informationCLASSIFICATION OF LOCATIONS FOR ELECTRICAL INSTALLATIONS IN GAS UTILITY AREAS. Gerry Pickens
CLASSIFICATION OF LOCATIONS FOR ELECTRICAL INSTALLATIONS IN GAS UTILITY AREAS Gerry Pickens Atmos Energy 810 Crescent Centre Drive Franklin, TN 37067 The National Electrical Code (NEC) defines hazardous
More informationBASIC NATIONAL ELECTRIC CODE APPLICABLE TO MEASUREMENT. Gerry Pickens. Atmos Energy 810 Crescent Centre Drive Franklin, TN 37067
BASIC NATIONAL ELECTRIC CODE APPLICABLE TO MEASUREMENT The National Electrical Code (NEC) defines hazardous locations as those areas "where fire or explosion hazards may exist due to flammable gases or
More informationBGA244 Binary Gas Analyzer
Quick Start Guide Revision 1.0 Certification Warranty Service certifies that this product met its published specification at the time of shipment. This product is warranted against defects in materials
More informationTechnical Data. General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm. Short-circuit protection
0102 Model Number Features Direct mounting on standard actuators Compact and stable housing Fixed setting EC-Type Examination Certificate TÜV99 ATEX 1479X Usable up to SIL2 acc. to IEC 61508 Accessories
More informationC&G 2395 Exam Paper June Section A-All questions carry equal marks. Answer all three questions. Show all calculations.
C&G 2395 Exam Paper June 2013 Section A-All questions carry equal marks. Answer all three questions. Show all calculations. 1. The electrical installation in an industrial unit is scheduled for a periodic
More informationChemical Feed Equipment Floor-Mounted Gas Dispenser - Series CH4200
Specification Bulletin (rev.01) Series CH4200 Chemical Feed Equipment Floor-Mounted Gas Dispenser - Series CH4200 Easy, fast& accurate digital with 11 points calibration Laser sensor offering actual feed
More informationTechnical Data. Dimensions
0102 Model Number Features 6 mm flush Usable up to SIL 3 acc. to IEC 61508 Application Danger! In safety-related applications the sensor must be operated with a qualified fail safe interface from Pepperl+Fuchs,
More informationSEMEM3-78 Testing and calibrating instrumentation and control equipment and circuits
Testing and calibrating instrumentation and control equipment and Overview This unit identifies the competences you need to carry out tests and calibration of instrumentation and control equipment and,
More informationTechnical Data. General specifications Switching element function Rated operating distance s n 1.5 mm
0102 Model Number Features 1.5 mm flush Accessories BF 8 Mounting flange, 8 mm Technical Data specifications Switching element function NAMUR, NC Rated operating distance s n 1.5 mm Installation flush
More informationPartial Stroke Testing. A.F.M. Prins
Partial Stroke Testing A.F.M. Prins Partial Stroke Testing PST in a safety related system. As a supplier we have a responsibility to our clients. What do they want, and what do they really need? I like
More informationIA CERTIFICATE (Annual review required by MASC covered by an additional letter) (Revision 2- Review & Review)
Certificate Number: MASC MS/11-127X Issue: 09 October 2017 Expire: 09 October 2020 Page: 1 of 5 IA CERTIFICATE (Annual review required by MASC covered by an additional letter) (Revision 2- Review & Review)
More informationEasySas. The most advanced airlock electronics on the market. Recyclable product. Eco-design. Energy savings
EasySas The most advanced airlock electronics on the market Eco-design Energy savings Recyclable product ELECTRONIC AIRLOCK MANAGEMENT SkySas range UniSas range CompacSas range An electronic management
More informationThermo Probe, Inc. TP-5 TP-7 TP-8. Instruction Manual English. Switch. Display. Carry Strap. Probe. Ground Clip. Switch. Display.
Display Thermo, Inc. Instruction Manual English TP-5 Display TP-7 Display TP-8 1-1 Thermo, Inc. Instructions for use- Models TP-5, TP-7, and TP-8 The manual describes basic function and use of Thermo instruments
More informationHigh-performance submersible pressure transmitter For level measurement in hazardous areas Model LH-20
Electronic pressure measurement High-performance submersible pressure transmitter For level measurement in hazardous areas Model LH-20 WIKA data sheet PE 81.56 Applications Deep well and borehole measurements
More informationHazardous Location Coding System - NEC 500. Type of Protection. XP = Explosionproof. IS = Intrinsically Safe Apparatus
Hazardous Location Equipment - United States Equipment listed in this category for Hazardous (Classified) Locations is also suitable for installations in areas that are unclassified locations and, unless
More informationDimensions. Technical Data General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm
Dimensions 65 9 5 14 40 35 11 9 5.4 M20 x 1.5 0102 S Model Number Features Direct mounting on standard actuators Compact and stable housing with terminal compartment connection Fixed setting Satisfies
More informationENS-200 Energy saving trainer
ENS-200 Energy saving trainer Find out about the essential aspects of energy efficiency in compressed air installations Save money Put it into practice Take care of the environment Get training www.smctraining.com
More informationGuidelines on Surveys for Dynamic Positioning System
Guidelines on Surveys for Dynamic Positioning System (2002) BEIJING 1 CONTENTS Chapter 1 GENERAL 1.1 General requirements 1.2 Class notation 1.3 Definitions 1.4 Plans and documents 1.5 Failure mode and
More informationElectronic gas volume corrector model DGVC-04
Electronic gas volume corrector model DGVC-04 1. Introduction The following user s manual gives information about the installation, configuration, usage and storage of the electronic gas volume corrector
More informationADVANTAGES DESCRIPTION MECHANICAL FITTINGS AND DIMENSIONS
03304 Float Gauge: Level measurement Application: LNG tanks Level 03304 E 1 ADVANTAGES - High level accuracy - Local mechanical counter read out. - High reliability - Suitable for 12 and 8 still well.
More informationIntrinsically Safe Acoustic Instrument Used in Troubleshooting Gas Lift Wells
Gas Well Deliquification Workshop Sheraton Hotel, Denver, Colorado February 17 20, 2013 Intrinsically Safe Acoustic Instrument Used in Troubleshooting Gas Lift Wells Lynn Rowlan, Echometer Company Carrie-Anne
More informationAMT-Ex Dewpoint Transmitter
AMT-Ex Dewpoint Transmitter Instruction Manual Alpha Moisture Systems Alpha House 96 City Road Bradford BD8 8ES England Tel: +44 1274 733100 Fax: +44 1274 733200 email: mail@amsytems.co.uk web: www.amsystems.co.uk
More informationSeries 6517 Katharometers. The ideal equipment for Process Monitoring and Control. Robust no moving parts. Designed for continuous industrial use
Data sheet Katharometers The ideal equipment for Process Monitoring and Control Designed for continuous industrial use Long working life Suitable for flammable gases CENELEC certified (ATEX) to EExia IIC
More informationIntelligent SUNTEX DC-5310(RS) Dissolved Oxygen Transmitter
Intelligent SUNTEX DC-5310(RS) Dissolved Oxygen Transmitter Overview C % ppm 4~20mA Analog Output ppb Power Supply 100~240 VAC mg/l Dimensions 96 x 96 x 132mm RS-485 Digital Output (for DC-5310-RS only)
More informationNZQA registered unit standard version 3 Page 1 of 6
Page 1 of 6 Title Report on the integrity of explosion-protected electrical apparatus in explosive atmospheres Level 3 Credits 3 Purpose This unit standard covers the explosion-protection aspects of plant
More informationRigel 601 CHECKBOX. Instruction Manual. 348A551 Issue 2.0. April Seaward Electronic Ltd. Issue 2.0
Rigel 601 CHECKBOX Instruction Manual 348A551 Issue 2.0 April 2006 2006 Seaward Electronic Ltd. Issue 2.0 Limited Warranty & Limitation of Liability Rigel Medical guarantees this product for a period of
More informationINSTRUCTION MANUAL. Lesker Model KJL615TC-K Lesker Model KJL615TC-H. Digital Vacuum Gauge/Controller. KJL615TC K/H Ranges
INSTRUCTION MANUAL Lesker Model KJL615TC-K Lesker Model KJL615TC-H Digital Vacuum Gauge/Controller KJL615TC K/H Ranges 1 to 1999 millitorr 1 to 1990 microbar 1 to 199.9 Pascal Standard Features Selectable
More informationDimensions. Technical Data General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm
Dimensions 7 36 5 33.5 9 5.4 30 65 0102 Model Number Features Direct mounting on standard actuators Fixed setting Satisfies machinery directive Compact and stable housing EC-Type Examination Certificate
More informationDimensions. Technical Data General specifications Switching element function DC Dual NC Rated operating distance s n 3 mm
Dimensions 65 9 5 40 35 14 11 9 5.4 M20 x 1.5 0102 Model Number Features Direct mounting on standard actuators Compact and stable housing with terminal compartment connection Fixed setting Satisfies machinery
More informationInstallation, operating and maintenance Instructions for Seemag bypass level indicator
Issue: S Date: 05-09-14 Type G35 General information The Seetru bypass magnetic level indicator, abbreviate SEEMAG, serves to show the filling level of fluids in tanks, basins, tubes etc. The Seemag operates
More informationTechnical Explanation
Technical Explanation for ESI Pressure Sensors Technical Explanation What is a pressure transmitter? A pressure transmitter (also called pressure transducer or pressure converter) is a component used to
More informationTransmitter CS 21 Operation Manual
Transmitter CS 21 Operation Manual 1194 Oak Valley Drive, Suite 20, Ann Arbor, MI 48108 800-959-0573 734-769-1888 Content Page For your Safety 3 General Description 3 Detection Principle 4 Operation 4
More informationSuccessful completion of the course leads to the award of the Technical Training Solutions Certificate of Competence 510: Instrumentation.
INSTRUMENTATION COURSE 510: 3 DAYS: Max 8 Candidates This course covers the key aspects of industrial instrumentation and is designed to enable maintenance personnel to carry out commissioning, calibration
More informationTwo-Wire In Situ Oxygen Analyzer (550 to 1400 C)
Product Data Sheet PDS 106-581.A01 March, 2004 Model 5081FG Two-Wire In Situ Oxygen Analyzer (550 to 1400 C) Intrinsically safe: - CENELEC EEx ia IIC - Class I Div. I Gr. B, C, D (pending) Operates at
More informationWireless I/O, Connecting Remote Sensors in a Wide Range of Environments
Gas Well Deliquification Workshop Sheraton Hotel, February 19 22, 2012 Wireless I/O, Connecting Remote Sensors in a Wide Range of Environments Glenn Longley, Sr. Product Manager FreeWave Technologies Agenda
More informationTemperature gauge Installation Guide
Temperature gauge Installation Guide improper functioning, or damage. Additional information can be found at: CAUTION: Read this installation guide carefully before unpacking the temperature gauge. Improper
More informationMANUAL DIRECT PURGE OPTION. UNION Instruments GmbH CWD2005 PLUS. General information, safety standards and regulations for direct purge option
MANUAL DIRECT PURGE OPTION UNION Instruments GmbH CWD2005 PLUS General information, safety standards and regulations for direct purge option Version: V1.00 Stand: 24.03.2010 Union Instruments GmbH Zeppelinstr.
More informationSinorix MANOB480, MANOCAB, MANOEOL Installation Maintenance
Sinorix MANOB480, MANOCAB, MANOEOL Installation Maintenance Building Technologies 2017-10-24 Control Products and Systems Legal notice Legal notice The specifications and availability are subject to change
More informationMETROTEC GSM. Type GSM. Oxygen measurement and control unit. *** Version 1.6 ***
Systems for oxygen measurement GSM Oxygen measurement and control unit Type GSM *** Version 1.6 *** Declaration of Conformity for Oxygen measurement and control unit GSM This device has been designed for
More informationHigh-performance submersible pressure transmitter For level measurement Model LH-20
Electronic pressure measurement High-performance submersible pressure transmitter For level measurement Model LH-20 WIKA data sheet PE 81.56 Applications Deep well and borehole measurements Groundwater
More informationMounting instructions. Strain transducer SLB-700A. B 26.SLB700A.10 e
Mounting instructions Strain transducer SLB-700A B 26.SLB700A.10 e SLB700A 3 Contents Page Safety instructions.............................................. 4 1 Applications..................................................
More informationIntrinsically explosion-proof and safety barrier introduction
Intrinsically explosion-proof and safety barrier introduction Summary of Topics Page 1. Explosion basic knowledge 1 2. Explosion groups 1 3. Zone classification 2 4. Explosion-proof electrical apparatus
More informationOperating Instructions
Operating Instructions Sensors Type 705 H 2 S Sensor and Transmitter for Electrochemical Cells Ul Certified HELPING TO MAKE A SAFER WORLD Ensure that you read and understand these operating instructions
More informationHigh-performance submersible pressure transmitter For level measurement Model LH-20
Electronic pressure measurement High-performance submersible pressure transmitter For level measurement Model LH-20 WIKA data sheet PE 81.56 Applications Deep well and borehole measurements Groundwater
More informationTechnical Data. Dimensions
0102 Model Number Features 2 mm flush Usable up to SIL2 acc. to IEC 61508 Technical Data specifications Switching element function NAMUR, NC Rated operating distance s n 2 mm Installation flush Output
More informationMANUAL KPS Pressure Control Valve
TetraTec Instruments GmbH Gewerbestrasse 8 71144 Steinenbronn Deutschland E-Mail: info@tetratec.de Tel.: 07157/5387-0 Fax: 07157/5387-10 MANUAL Pressure Control Valve *** VERSION 1.0 *** Update: 17.11.2006
More informationKGW - ISOTHERM. Operating Instructions. Level controlling device for liquid nitrogen LEVEL CONTROL LN2
KGW - ISOTHERM Germany 76185 Karlsruhe Gablonzer Straße 6 Tel. 0049 / 721 / 95897-0 Fax. 0049 / 721 / 95897-77 email:info@kgw-isotherm.de Internet: www.kgw-isotherm.de Operating Instructions Level controlling
More informationSIL Safety Manual. ULTRAMAT 6 Gas Analyzer for the Determination of IR-Absorbing Gases. Supplement to instruction manual ULTRAMAT 6 and OXYMAT 6
ULTRAMAT 6 Gas Analyzer for the Determination of IR-Absorbing Gases SIL Safety Manual Supplement to instruction manual ULTRAMAT 6 and OXYMAT 6 ULTRAMAT 6F 7MB2111, 7MB2117, 7MB2112, 7MB2118 ULTRAMAT 6E
More information