September 23, 2016 Site Safe, Inc.
|
|
- Ethel Tyler
- 6 years ago
- Views:
Transcription
1 RF Exposure Utility Worker Safety and Small Cells September 23, 2016 Site Safe, Inc.
2 RF SAFETY Radio Frequency (RF) Safety is worker and general public safety around wireless transmitters September 23, 2016 Site Safe, Inc. 2
3 REGULATORY FCC AND OSHA OSHA General Duty Clause Employer shall furnish a safe workplace Employee has a right to know about hazards and shall comply with safety standards FCC - Rules, Part 1, Subpart I Exposure limits Rule Rules based on NCRP / ANSI / IEEE recommendations (consistent with International rules ICNIRP) Under review (2014 NOI) September 23, 2016 Site Safe, Inc. 3
4 EXPOSURE LIMITS FCC Exposure Limits - two levels of protection Occupational or Controlled Limits 10 time safety factor below known biological effects General Population or Uncontrolled Limits are 5 times additionally lower (total of 50 times safety factor) Occupational: personal who through training are aware of and can control their exposure Limits Based on Spatial & Time Averaging whole body exposure over time Partial Body (hands, head, etc.) exposure limits are higher September 23, 2016 Site Safe, Inc. 4
5 WHAT DOES IT MEAN? RF exposure at high levels can be dangerous Know where exposure exceeds limits RF Exposure Assessment (modeling / measurement) Knowing where it is safe to work will ensure safety If you have to work where exposure may or does exceed limits, take appropriate action Safety Concern - wireless sites with workers who may or must be close to antennas Relative Risk (versus High Voltage, Fall Protection, etc.) Medical Implants use the General Public limit unless approved by physician September 23, 2016 Site Safe, Inc. 5
6 RF AWARENESS TRAINING Training provided to make someone qualified to work in areas that exceed the General Public exposure limits. The goal of training is to allow a worker to be aware of and control their exposure. RF Basics Regulations How to Work Safely Specific for an installation or type of installations (DAS) General for working at (most) RF installations Expanded for managers, safety officers, designers A trained worker may work in areas that exceed the General Public Limit All Day September 23, 2016 Site Safe, Inc. 6
7 RF ALERTING SIGNS Blue Notice Sign This sign indicates an area where exposures may exceed General Public limits. RF levels may be greater than the General Public limits but they will be less than the limits for human exposure or the Occupational limits. Work can safely be done in this area with no time restrictions or need for personal monitors or other controls. Workers should be aware of antenna locations and understand that if they must work above the walking surface near antennas, additional precautions are required. Yellow Caution Sign This sign indicates an area where RF levels may exceed Occupational or human exposure limits.! CAUTION Workers should use personal monitors to determine if exposure in their work area exceeds limits, paying close attention to areas immediately in front of antennas. Reduced power or turning off transmitters may be required to work in this area for more than a few minutes.
8 RF ALERTING SIGNS Orange Warning Sign This sign is used to indicate areas which greatly exceed Occupational or human exposure limits and immediate harm may result. Typically, these signs are placed on broadcast or other high power installations. Working in areas with orange Warning signs must include coordination with the antenna owner, the power should either be reduced or turned off, and monitoring or lock-out-tag-out procedures must be employed. September 23, 2016 Site Safe, Inc. 8
9 RF MONITORS Only useful in combination with RF Awareness training Used to determine personal exposure right now Review manufactures specs is it right for your environment? some have limited frequency Ascertain if antennas that you are working near are active or not September 23, 2016 Site Safe, Inc. 9
10 UTILITY POLES Antennas at tops of poles have little exposure risk Different types of installations will have different distances to exposure limit perimeter Below the antennas, exposure levels are generally well below limits Disconnects can ensure no RF exposure September 23, 2016 Site Safe, Inc. 10
11 TRANSMISSION TOWERS Antennas at tops of poles have little exposure risk Climb or lift through - caution September 23, 2016 Site Safe, Inc. 11
12 OTHER SITES Behind antennas little exposure Microwave Dishes very little exposure Omni Antennas Land Mobile can cause levels to exceed limits (but are usually intermittent) Caution using lifts in front of antennas September 23, 2016 Site Safe, Inc. 12
13 MICROWAVES Microwave Dishes / Panels have high gain and typically little transmitter power For most there is no area that exceeds limits Follow signs Don t stand in front it will block the signal and make the microwave link fail! September 23, 2016 Site Safe, Inc. 13
14 SAFETY PRACTICE IN ACTION If workplace exceeds Occupational limits: shutdown antenna and verify with RF monitor (if no disconnect / lockout / tagout) Trained worker can be in area that does not exceed Occupational limits Trained workers may pass through area that does time averaging September 23, 2016 Site Safe, Inc. 14
15 QUESTIONS Matt Butcher, PE VP Engineering Site Safe, Inc. 200 North Glebe Road, Suite 1000 Arlington, VA U.S.A. Office: (703) Mobile: (703) Website: September 23, 2016 Site Safe, Inc. 15
Telecommunication Tower Technician Course Descriptions
Telecommunication Tower Technician Course Descriptions Developed by: TES, Inc. 10909 Murdock Drive Knoxville, TN 37932 800-327-4036 O*NET-SEC CODE: 49-2021.00 RAPIDS CODE: 2030CB Approved By US Department
More informationControl of Hazardous Energy Lockout / Tagout Program
Control of Hazardous Energy Lockout / Tagout Program August 2016 Table of Contents Purpose... 1 Scope and Application... 1 Responsibilities... 1 Environmental Health and Safety Personnel (EH&S)... 1 Directors
More informationHazardous Energy Control (Lockout-Tagout)
Hazardous Energy Control (Lockout-Tagout) The purpose of this program is to prevent inadvertent operation or energization of machines, equipment, or processes in order to protect employees and establish
More informationHealth & Safety Policy and Procedures Manual SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY
SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY 1. CONTROL OF HAZARDOUS ENERGY POLICY AND PROCEDURES A. OSHA References: 29 CFR 1910.147, 29 CFR 1910.332, 29 CFR 1910.333, 29 CFR 1926.417 B.
More informationLockout/Tagout - Control of Hazardous Energy Program
Lockout/Tagout - Control of Hazardous Energy Program The University Of Iowa Environmental Health & Safety 122 Grand Avenue Court Iowa City, IA 52242-1000 Phone: 319-335-8501 Date Revised/Reviewed: 6/8/2018
More informationControl of Hazardous Energy. Environmental Health and Safety
Control of Hazardous Energy Environmental Health and Safety 11/01/2014 1 CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT) OSHA CFR 1910.147 Revised Date: November 2014 STATEMENT OF POLICY Ball State University
More informationARKANSAS TECH UNIVERSITY FACILITIES MANAGEMENT HEALTH AND SAFETY MANUAL (LOCKOUT/TAGOUT) 30.0
() 30.0 The purpose of the Energy Control Policy (Lockout/Tagout) is to ensure that before any employee performs any servicing and/or maintenance on machinery or equipment, where the unexpected energizing,
More informationProduct Information Report Lockout/Tagout Hazardous Energy Control
Overview A properly implemented (LOTO) program is designed to protect workers involved in the maintenance and servicing of equipment from the dangerous effects of hazardous energy caused by the unexpected
More informationNESC WORKSHOP Revisions to Part 4 (Work Rules) Sam Stonerock. October 18, 2016
NESC WORKSHOP 2017 Revisions to Part 4 (Work Rules) Sam Stonerock October 18, 2016 Work Rules for the Operation of Electric Supply and Communications Lines and Equipment 2017 edition Reconcile existing
More informationDUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM
DUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Introduction 2 Regulatory Requirements 2 Protective Materials
More informationArc Flash. Safety 21
Arc Flash Safety 21 Arc Flash Introduction Electrical Hazards Safety Planning De-Energizing Equipment Working Hot Summary Introduction Most people don t think about electricity very much, which is surprising
More informationFacilities Management
Facilities Management Policy Number: 700.6 Title: Lockout/Tag Out Policy Implementation Date: 2004 Last Audited: July 2 nd, 2018 Last Revised: March 25 th, 2015 Introduction This policy contains the necessary
More informationLockout / Tag out Program
Lockout / Tag out Program Presented by DOSHTI www.doshti.com You will learn Purpose of Lockout- Tag out Requirements for LOTO Types of Hazardous Energy Procedures for LOTO The OSHA Standard for the Control
More informationLOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM
LOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.147 BASIS: Approximately three million workers in the United States face risks from uncontrolled energy when servicing machinery
More informationHealth and Fire Safety Review 2/15
Health and Fire Safety Review 2/15 1 TABLE OF CONTENTS Page 3 Scope 3 Control of Hazardous Energy (Introduction) 3 Authorized Employee 3 Employer Responsibility 4 Tagout Devices 4 Lockout Devices 5 General
More information2523-LDG-E. Leader s Guide
2523-LDG-E LOCKOUT/TAGOUT TRAINING FOR EMPLOYEES Leader s Guide 2008 ERI Safety Videos LOCKOUT/TAGOUT TRAINING FOR EMPLOYEES This easy-to-use Leader s Guide is provided to assist in conducting a successful
More informationLockout/Tagout Safety Policy
University of North Carolina Wilmington Environmental Health & Safety Workplace Safety Lockout/Tagout Safety Policy GENERAL The UNCW Environmental Health & Safety Department (EH&S) is authorized by UNCW
More informationLOCKOUT/TAGOUT PLAN August 2015
LOCKOUT/TAGOUT PLAN August 2015 Office of Environmental Health and Safety 423-354-5224 TABLE OF CONTENTS Purpose and Intended Use... 2 A. Types of Energy Sources... 2 B. Activities Requiring Lockout/Tagout
More informationLO/TO LOCKOUT/TAGOUT PROGRAM
LO/TO LOCKOUT/TAGOUT PROGRAM April 2017 CONTENTS Section 1: Introduction...1 Section 2: Purpose... 1 Section 3: Application... 1 Section 4: Definitions... 2 Section 5: Roles and Responsibilities... 4 Section
More informationLockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR
Volunteer State Community College Lockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR 1910.147 The information contained in this maual documents the policies and procedures
More informationPAGE 1 OF 7 HEALTH, SAFETY & ENVIROMENTAL MANUAL PROCEDURE: S230 Lock-Out Tag-Out (LOTO) Program REV 4.0 8/13/2012
PAGE 1 OF 7 LOCK-OUT TAG-OUT (LOTO) THE CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM PURPOSE: 1. This standard establishes lockout/tagout (LOTO) procedures for the safety of personnel working on
More informationEffective Date: 26, October 2016 TITLE: COLOR CODING AND ACCIDENT PREVENTION SIGNS AND TAGS GUIDELINES
Version: 2 Page: 1 of 5 1.0 Introduction 1.1 Purpose The purpose of this guideline is to communicate information and to establish a method for marking physical hazards. 1.2 Scope This guideline is intended
More informationHazardous Energy Control
Lockout Tagout This program has been prepared to provide assistance in compliance with USA OSHA standards and/or Best Management Practices. It should not be used without consideration of the unique conditions
More informationUniversity of Arkansas Office of Environmental Health and Safety
University of Arkansas Office of Environmental Health and Safety Procedure Name: Lockout / Tagout Procedure Number: 600.26 Effective Date: 12-1-2015 Procedure: Developed in accordance with the OSHA Control
More informationCONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM
CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM 1.0 REGULATORY AUTHORITY Code of Federal Regulations, 29 CFR 1910.147; California Code of Regulations, Title 8, Sections 2320.1 and 3314; CSU, Fullerton
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All Task: Replace a Light Ballast Job Title(s) Performing Task: Electrician, Maintenance
More informationWESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107
WESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107 Draft Issued 12/97 Revised 11/00 Please direct any questions or comments about the applicability of this document to Luigi Marcone, WCSU
More informationLOCKOUT/TAGOUT PROGRAM
Santa Clarita Community College District LOCKOUT/TAGOUT PROGRAM Revised March 2018 TABLE OF CONTENTS PURPOSE... 3 COMPLIANCE...4 DEFINITIONS...5 SECTION I - ENERGY CONTROL PROCEDURES... 7 SECTION II -
More informationLOCKOUT-TAGOUT PROGRAM
LOCKOUT-TAGOUT PROGRAM Please Note: This material, or any other material used to inform employers/employees of compliance requirements of OSHA standards through simplification of the regulations should
More informationLockout Tagout Program
Lockout Tagout Program Table of Contents INTRODUCTION... 2 FORWARD... 2 OBJECTIVE... 2 APPLICABILITY... 2 RESPONSIBILITIES... 3 PROGRAM ENFORCEMENT... 4 RECORDKEEPING... 4 LOCKOUT TAGOUT EQUIPMENT... 5
More informationTHE CITADEL The Military College of South Carolina 171 Moultrie Street Charleston, SC MEMORANDUM 30 June 2017 NUMBER (X)-(Y) CONFINED SPACE
THE CITADEL The Military College of South Carolina 171 Moultrie Street Charleston, SC 29409 MEMORANDUM 30 June 2017 NUMBER (X)-(Y) 1. PURPOSE CONFINED SPACE The purpose of The Citadel s Confined Space
More informationSAINT MARY S COLLEGE OF CALIFORNIA STANDARD HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT. Prepared by
SAINT MARY S COLLEGE OF CALIFORNIA STANDARD 1.1.4 HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT Prepared by SAINT MARY S COLLEGE OF CA MORAGA, California KAREN LAURICELLA Original Date: 1 JULY
More informationAbove ground or below, worker and jobsite safety is your priority and ours.
Above ground or below, worker and jobsite safety is your priority and ours. Webinar October 25 th, 2016 Bridging To The New Confined Space Standard in Construction "This rule will save lives of construction
More informationConfined Space Entry Program
Confined Space Entry Program August 2016 Table of Contents Purpose... 1 Scope and Application... 1 Responsibilities... 2 Environmental Health and Safety (EH&S)... 2 Entry Supervisor... 2 Attendant... 2
More informationPage: 7/15/2009. Energy control procedures Use of lockout/tagout equipment to ensure safe work practices.
1 of 6 1.0 PURPOSE This program applies to the installation, service, maintenance, or removal of any type of machinery, equipment, or components, in which the unexpected start up or release of stored energy
More informationLockout / Tagout Safety Program
Lockout / Tagout Safety Program Prepared by: The Ohio State University Environmental Health and Safety Occupational Safety & Industrial Hygiene 1314 Kinnear Road Columbus, OH 43212-1168 614-292-1284 Phone
More informationGettysburg College. Energy Control Program
Gettysburg College Energy Control Program Adopted October 2009 Reviewed and Updated February 2015 Reviewed and Updated July 2015 I. Energy Control Procedures Table of Contents A. General Lockout Procedures
More informationCITY AND COUNTY OF DENVER CR&CF RISK UNIT Safe Operating Procedure
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.4.2 Safe Operating Procedure 1.0 Introduction Safe Operating Procedures (SOPs) shall be developed for complex or ongoing activities that present a risk of serious
More informationH. Control of Hazardous Energy: Lockout/Tag Out
H. Control of Hazardous Energy: Lockout/Tag Out 1. Purpose Control of Hazardous energy is the purpose of the Lockout- Tagout Program. This program establishes the requirements for isolation of both kinetic
More informationLockout/Tagout Training Overview. Safety Fest 2013
Lockout/Tagout Training Overview Safety Fest 2013 Purpose of Lockout/Tagout The standard covers the servicing and maintenance of machine and equipment in which the unexpected energization or start up of
More informationSAFETY DIRECTIVE. 2.0 DEPARTMENTS AFFECTED This directive applies to all departments and employees of the Town of Marana.
SAFETY DIRECTIVE Title: Safety Signs and Accident Prevention Tags Issuing Department: Town Manager s Safety Office Effective Date: September 1, 2014 Approved: Gilbert Davidson, Town Manager Type of Action:
More informationDuPage County Environmental, Safety, Health & Property Loss Control Program Hazardous Energy Control (Lockout/Tagout)
Purpose: To provide the minimum requirements for the lockout or tagout of energy isolating devices whenever work is performed or servicing is done on County of DuPage machinery, equipment, vehicles and
More informationE2.14 Control of Hazardous Energy. Effective Date: 03/01/2018
University Policy Volume E2: Environment, Health, Safety and Security E2.14 Control of Hazardous Energy Responsible Office: Facilities Management Responsible Officer: Safety Officer POLICY STATEMENT All
More informationSafe Work Practices / Procedures / Instruction CONFINED SPACE
CONFINED SPACE Entry into and work in a confined space poses health and safety problems which may include: Presence or possible build up of a hazardous atmosphere Unexpected movement of equipment or materials
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
1. De-energize circuit serving the outlet following LOTO procedure (see pages 3 5). PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All
More informationLockout/Energy Control
Lockout/Energy Control Presented By: Sotaris, LLP 2000 Auburn Drive, Suite 200 Beachwood, Ohio 44122 P: 216-378-7650 F: 866-794-5756 W: www.sotaris.com E: awj@sotaris.com 1 About Me Andrew W. Johnson,
More informationElements of a Lockout/Tagout Program OSHA
September 15, 2015 Elements of a Lockout/Tagout Program OSHA 1910.147 Dayna Noble Industrial Safety Consultant Specialist Ohio BWC 567-204-8917 Dayna.noble@bwc.state.oh.us Top 10 most frequently cited
More informationSafety Manual: Hazardous Energy. January, 2017
Safety Manual: Hazardous Energy January, 2017 9.0 Hazardous Energy Introduction Energized equipment in the workplace pose a significant risk of injury and death. If the unexpected energization or start-up
More informationUniversity of Vermont Department of Physical Plant Burlington, Vermont
University of Vermont Department of Physical Plant Burlington, Vermont CONTROL OF HAZARDOUS ENERGY SOURCES AND ELECTRICAL HAZARDS LOCKOUT AND TAGOUT PROGRAM in accordance with OSHA 29 CFR 1910.147 REVISED
More informationTexas Department of Insurance Division of Workers Compensation. Lockout Tagout HS96-100D (8-06)
OF OF STATE THE TEXAS TEXAS Texas Department of Insurance Division of Workers Compensation Lockout Tagout HS96-100D (8-06) Contents Purpose 1 Definitions 1-2 Responsibility 2-3 Training 3 Periodic Inspections
More informationLockout/Tagout Program
Lockout/Tagout Program Prepared by: Occupational Health and Safety Reviewed by: Joint Health and Safety Committees Approved by: Chief Human Resources Officer November 2014 TABLE OF CONTENTS 1.0 Purpose...3
More informationLockout/Tagout Program
Purpose Hazardous energy appears in the workplace in the form electrical, mechanical, pneumatic, hydraulic and thermal energy and includes chemical, water, steam and gaseous energy systems. Lockout/Tagout
More informationControl of Hazardous Energy Program (Lockout/Tagout)
Control of Hazardous Energy Program (Lockout/Tagout) 1 The Control of Hazardous Energy (Lockout/Tagout) Program 1910.147 The following lockout/tagout program is provided to assist employees in complying
More informationControl of Hazardous Energy (Lockout/Tag-out) 29 CFR
Control of Hazardous Energy (Lockout/Tag-out) 29 CFR 1910.147 What Is Lockout/Tag-out? Referred to as LOTO Blocks flow of energy from power source to the equipment Provides means of warning (tag) Regulatory
More informationLockout / Tagout Program. The Control of Hazardous Energy. Environmental Health and Safety Office
Lockout / Tagout Program The Control of Hazardous Energy Environmental Health and Safety Office Revised: 07/2014 TABLE OF CONTENTS 1.0 PURPOSE STATEMENT... 1 2.0 SCOPE:... 1 3.0 RESPONSIBILITY:... 2 4.0
More informationTHE UNIVERSITY OF NORTH CAROLINA
THE UNIVERSITY OF NORTH CAROLINA AT CHAPEL HILL CHILLED WATER DEPARTMENT ENERGY CONTROL PROCEDURE The purpose of this document is to establish minimum requirements for the manual isolation and securing
More informationOccupational Protective Equipment
Introduction One of the leading occupational dangers in today s workforce is the risk of death or injury due to falls. Falls from ladders, scaffolds, buildings, or other elevations have become the second
More information: Electric Power Generation, Transmission, and Distribution. Region IV - OSHA
1910.269: Electric Power Generation, Transmission, and Distribution Region IV - OSHA Scope This standard covers the operation and maintenance of electric power generation, control, transformation transmission,
More informationA Review of Key Requirements
REGULATORY COMPLIANCE OSHA s Lockout/Tagout Standards: A Review of Key Requirements By ABDALLA M. MUTAWE, RONALD TSUNEHARA and LYNDA A. GLASPEY This article reviews key elements of OSHA standards designed
More informationLOCKOUT/TAGOUT: Operating Procedure TABLE OF CONTENTS
LOCKOUT/TAGOUT: Operating Procedure TABLE OF CONTENTS A. PURPOSE 1 B. FACILITIES STAFF RESPONSIBILITIES 2 C. TRAINING AND RETRAINING of AFFECTED and EUTHORIZED EMPLOYEES 3 NINE POINTS TO REMEMBER 5 LOCKOUT/TAGOUT
More informationLockout Tagout Program
Lockout Tagout Program RIM of the World Unified School District 27315 North Bay Road Blue Jay, CA 92352 (909) 336-4100 July 2016 Safety and Risk Management Department RIM of the World Unified School District
More informationELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR CFR , ,
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.331 335-29 CFR 1926.302, 1926.416, 1926.417 BASIS: The National Safety Council estimates that there are at least 300 deaths
More informationLockout / Tagout Program OSHA 29 CFR
Lockout / Tagout Program OSHA 29 CFR 1910.147 Baylor University utilizes outside contractors to perform set-up, maintenance, service, and repair to equipment utilized on campus. University staff perform
More informationThis session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its
This session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its standard on Control of Hazardous Energy. This is part
More informationEnergy Control. Suite 2A, 55 Frid Street Hamilton, ON L8P 4M3 office: cell:
Energy Control Suite 2A, 55 Frid Street Hamilton, ON L8P 4M3 office: 905.577.0303 cell: 905.977.0210 consultant@staffaid.ca www.staffaid.com Safety, Energy Control, Power Lockout & Function Test Procedures
More informationAccident Prevention Signs and Tags
Accident Prevention Signs and Tags 1910.145 Specifications for accident prevention signs and tags. (a) Scope. (1) These specifications apply to the design, application, and use of signs or symbols (as
More informationLockout - Tagout. Control of Hazardous Energy OSHA Standard
Lockout/Tagout Lockout - Tagout Control of Hazardous Energy OSHA Standard 1910.147 What Is Lockout/Tagout? Referred to as LOTO Blocks the flow of energy from power source to the equipment Provides means
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT) PROGRAM
Page: 1 of 15 1.0 Purpose and Applicability 2.0 Scope 1.1 It is the policy of the University of Pennsylvania in coordination with the Office of Environmental Health and Radiation Safety to provide the
More informationRiskTopics. Lockout/Tagout October 2017
RiskTopics Lockout/Tagout October 2017 This Risktopic is designed to outline guidelines for lockout/tagout and provide assistance in developing a management program to reduce the risk of injury from unintended
More informationSECTION 51 NFPA 70E POLICY. Health & Safety Policy and Procedures Manual
SECTION 51 NFPA 70E POLICY Health & Safety Policy and 1. Protection Against Arc Flash A. Policy: An arc flash is a dangerous condition associated with the release of energy caused by an electric arc. An
More informationPRESCOTT SCHOOL DISTRICT NO South A Street Prescott, WA The Control of Hazardous Energy (Lockout/Tagout)
PRESCOTT SCHOOL DISTRICT NO. 402-37 207 South A Street Prescott, WA 99348 509-849-2217 The Control of Hazardous Energy (Lockout/Tagout) I. Purpose The Control of Hazardous Energy (Lockout/Tagout) This
More informationOKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM. Environmental Health and Safety. Established:
OKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM Environmental Health and Safety Established: Developed in accordance with OSHA Standard 29 CFR 1910.147 1 1.0 SCOPE. Oklahoma City Community
More informationUniversity of Tennessee Safety Program
University of Tennessee Safety Program Policy Subject: Lockout/Tagout Program Effective Date: 4/22/98 Area Affected: All areas on campus where equipment can be locked out for service. Contact Information:
More informationSAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT
SAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT SAMPLE WRITTEN PROGRAM The objective of this procedure is to establish a means of positive control to prevent the accidental starting
More informationThis is (Enter Company Name Here) Arc Flash Prevention policy. (Enter Name Here) will be responsible for overall direction of the Safety Program.
Company Name: Policy/Procedure ID Number: 222 Date: Grainger Safety Services Inc. 2012 Arc Flash Prevention Policy This is (Enter Company Name Here) Arc Flash Prevention policy. (Enter Name Here) will
More informationHealth, Safety, Security and Environment
Document owner and change code Document Owner Aaron Perronne Title HSSE Manager Mark X Change Code Description X N/A First Issue A Typographical/Grammatical correction; formatting change; text clarification-no
More informationLock Out/Tag Out Control of Hazardous Energy
Lock Out/Tag Out Control of Hazardous Energy University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells 1.0 Program Objective UF
More informationLockout/Tagout - Energy Control Program
Lockout/Tagout - Energy Control Program Lockout and Tagging of ELECTRICAL Circuits This portion of the K.R. Miller Contractors, Inc. safety program has been created to maintain a written copy of procedures
More informationLockout/Tagout Manual
Manual 2408 Wanda Daley Drive Ames, Iowa 50011-3602 (515) 294-5359 www.ehs.iastate.edu Copyright Environmental Health and Safety 2809 Daley Drive Ames, IA 50011-3660 Ph: (515) 294-5359 www.ehs.iastate.edu
More information2008. AURORA PICTURES
2923 LOCKOUT/TAGOUT: It Would Have Saved His Life 2008. AURORA PICTURES 1 Table of Contents Introduction 3 Video Overview.3 Introduction 3 Purpose of Lockout/Tagout 3 Hazardous Energy Sources.3 Authorized
More informationLeader s Guide ERI Safety Videos
1717 SAFE ELECTRICAL WORK PRACTICES & THE 2018 NFPA 70E Leader s Guide ERI Safety Videos SAFE ELECTRICAL WORK PRACTICES & THE 2018 NFPA 70E This easy-to-use Leader s Guide is provided to assist in conducting
More informationIsolation and Lockout
Work Procedure Facilities Management UBCO-RMS-OHS-WP 16-001 Date Created: July 13, 1999 Date Updated: April 4, 2016 Supersedes: September 18, 2003 1. SCOPE Isolation and Lockout This procedure establishes
More informationEmergency Response Plan
Regulatory Citation What It Is Who It Applies To OSHA - 29 CFR 1910.120(q)(1) - Emergency Response Plan Standard improves the ability of employees and employers to respond to emergencies caused by releases
More information2. The purpose of this program is to achieve the following objectives:
Section 16A. Lockout and Tagout Program 1. In the course of their duties, personnel at the TFREC may need to secure controls, switches, and equipment in order to prevent injury caused by the sudden, unexpected
More informationPOTENTIAL HEALTH & SAFETY HAZARDS
Number: OH&S 18.09.1 Revision Date: 2011.06 Confined Space 1. PURPOSE 2. SCOPE 1.1. To properly designate Confined Spaces (CS) at Thompson Rivers University (TRU), to provide guidance to ensure the safety
More informationElectrical Safety Work Practices
Work Practices I. SCOPE This program covers any SOUTHWESTERN COMMUNITY COLLEGE employee that may work or be exposed to exposed electrical systems: To assure that employees are not exposed to potentially
More informationLOCKOUT/TAGOUT PROGRAM
0 Appendix C OCCUPATIONAL SAFETY AND HEALTH PROGRAM LOCKOUT/TAGOUT PROGRAM Hazardous Energy Control Lockout/Tagout Program TABLE OF CONTENTS Section Page I. Purpose and Scope. 1 II. Definitions 1 III.
More informationElectrical Safety Program
Environmental Safety Electrical Safety Program 50V-1000V The purpose of Clemson University s (CU) Electrical Safety Program is to protect all staff, students, and faculty from electrical hazards. Clemson
More informationCITY OF NEW LONDON LOCKOUT/TAGOUT PROGRAM
CITY OF NEW LONDON LOCKOUT/TAGOUT PROGRAM (HAZARDOUS ENERGY CONTROL) May 1, 2003 1 LOCKOUT/TAGOUT PROGRAM (HAZARDOUS ENERGY CONTROL) I. PURPOSE The purpose of this Hazardous Energy Control Program is to
More informationResponsibilities / Accountability
Responsibilities / Accountability What we will cover Brief history of OPP safety program OPP s commitment to safety Safety responsibilities Accountability for safety Employee expectations History of Safety
More informationE n v i r o n mental Health & S a f ety
E n v i r o n mental Health & S a f ety Policy & Procedure Manual Title: EH&S 1-6 Effective Date: 1/7/06 Revision Date: 5/11 Reviewed Date: 8/03/2015 1. Purpose: To establish safe working practices for
More informationSAFETY GUIDELINES. Table of Contents
Table of Contents 1. Purpose 2. Application 3. Areas of Responsibility 4. Definitions 5. Procedures 5.1 Supervisor responsible for the work 5.2 Supervisor or person in charge of the work 5.3 Supervisor
More informationIssue: Issued By: Environment, Health & Safety Part: Hazard Identification and Assessment Revision #: 2 Revision
Control of Hazardous Energy Program Section: Occupational Health and Safety Date of 2007.07.24 Management System Issue: Issued By: Environment, Health & Safety Part: Hazard Identification and Assessment
More informationWays to Meet OSHA Requirements for Safety Signage
Safety Sign Training Ways to Meet OSHA Requirements for Safety Signage References: 29 CFR 1910.145 and ANSI Z535 Standard This material was developed by MCLBA, Risk Management. It does not necessarily
More informationSafety Sign Assessment for Frequently Endangered Employees
SAFE Safety Sign Assessment for Frequently Endangered Employees Guidelines: This checklist covers the regulations issued by the U.S. Department of Labor - OSHA under the General Industry standards 29 CFR
More informationEM Section 12. Control of Hazardous Energy (Lockout/Tagout)
EM 385-1-1 Section 12 Control of Hazardous Energy (Lockout/Tagout) Lockout/Tagout References EM 385-1-1 Section 12 29 CFR 1926.600 (a) (3) i Heavy Equipment 29 CFR 1926.702 (j) (1) Concrete Tools 29 CFR
More informationAccident Prevention Signs and Tags Safety Training Course
Accident Prevention Signs and Tags Safety Training Course Copyright protected. All rights reserved. ATTENTION! This PowerPoint training presentation provides safety education and information to our employees
More informationManagement Plan for Lockout Tagout (LOTO) ISD #535
Management Plan for Lockout Tagout (LOTO) ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9½ Street Rochester, MN 55904 507-328-4507 Modification Date Document Modification Form All
More informationCONTROL OF HAZARDOUS ENERGY
SECTION 12 CONTROL OF HAZARDOUS ENERGY 12.A GENERAL 12.A.01 This Section shall apply to contractor-managed Hazardous Energy Control Programs (HECP) only, as well as all requirements of 1910.147, ANSI Z244.1,
More informationEM385 Construction Safety and Health Certification Course Section 12 Control of Hazardous Energy
EM385 Construction Safety and Health Certification Course Section 12 Control of Hazardous Energy OSHAcademy Course 501 Study Guide EM 385 SAFETY AND HEALTH CERTIFICATION COURSE - SECTION 12 Edited by:
More information