INSTALLATION INSTRUCTIONS FOR ELECTRONIC SENSOR ACTIVATED LAVATORY FAUCETS

Transcription

1 ode No Rev. 1a (11/06) INSTLLTION INSTRUTIONS FOR ELETRONI SENSOR TIVTED LVTORY FUETS EF-100 Series Transformer Powered Sensor ctivated Lavatory Faucets EF-150 Series attery Powered Sensor ctivated Lavatory Faucets LIMITED WRRNTY Sloan Valve ompany warrants its Optima EF-100 and EF-150 Series Electronic Hand Washing Faucets to be made of first class materials, free from defects of material or workmanship under normal use and to perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years from date of purchase. During this period, Sloan Valve ompany will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve ompany, at customer s cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor, transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve ompany s products directly from Sloan Valve ompany for purpose of resale. This warranty does not cover the life of the battery. THERE RE NO WRRNTIES WHIH EXTEND EYOND THE DESRIPTION ON THE FE HEREOF. IN NO EVENT IS SLON VLVE OMPNY RESPONSILE FOR NY ONSEQUENTIL DMGES OF NY MESURE WHTSOEVER. FUET VRITIONS -ISM Integral Spout Mixer -I -lick Feature -DPU Drain Pop Up -P Plug-in Transformer (EF-100 Series) -LT Less Transformer (EF-100 Series) PRIOR TO INSTLLTION Prior to installing the Sloan Optima EF-100/150 Series Faucets, install the items listed below. lso, refer to rough-in illustrations. Lavatory/sink Drain line Hot and cold water supply lines or pre-tempered water supply line. Important: LL PLUMING SHOULD E INSTLLED IN ORDNE WITH PPLILE ODES ND REGULTIONS. FLUSH LL WTER LINES PRIOR TO MKING ONNETIONS. KEEP THRED SELNT OUT OF YOUR WTERWY TO PREVENT OMPONENT PRT DMGE! DO NOT USE NY SELNT ON OMPRESSION FITTINGS. Trim Plates When the EF Faucet is installed on a sink that has three () hole punchings, a Trim Plate should be used. Trim Plates must be specified and ordered separately. ETF-607- Trim Plate for (10 mm) enterset Sink ETF-608- Trim Plate for 8 (0 mm) enterset Sink TOOLS REQUIRED FOR INSTLLTION 1 mm open end wrench for male end of flex hose 1 mm open end wrench or nut driver for faucet retainer nut / open end wrench for female end of flex hose FUET ROUGH-IN MODELS EF-100/150. gpm (8. Lpm) Max. Flow erator Faucets with Single Line Water Supply SPOUT 1-/16 (0 mm) MIN. DI. HOLE REQUIRED MODELS EF-100/150-ISM MODELS EF-100/150-ISM-DPU-I. gpm (8. Lpm) Max. Flow erator Faucets with Hot and old Water Supply SPOUT MIXING VLVE (an e Set and Removed) 1-/16 (0 mm) MIN. DI. HOLE REQUIRED FUET SPOUT DIMENSIONS & POP UP DETILS POP UP MODELS EF-100/150-ISM-DPU-I ONLY 5-9/16 (1 mm) º 6-7/8 (175 mm) GSKET RETINER TEMPERED 1-1/ (8 mm) MX. DEK THIKNESS 1 (0 mm) LONG FLEX HOSE If a connection to separate hot and cold water supplies is desired, then a ak-hek tee fitting (not supplied) must be used prior to connecting to the faucet. GSKET RETINER HOT 1 (0 mm) LONG FLEX HOSES 1-1/ (8 mm) MX. DEK THIKNESS OLD -/8 (60 mm) -/8 (60 mm) -/ (70 mm) When installing the Faucet on a three () hole sink, make sure that the center hole is large enough to accommodate the Faucet shank. 1-/16" (0 mm) minimum diameter hole is required. NOTE: 1-7/ (1 mm) Diameter hole is required if the deck is greater than 1/ (1 mm) thick.

2 1 Install Faucet. Remove Nut, Faucet Retainer and Gasket. Do Not remove the O-ring from base of Faucet. Slide Gasket over Flex Hose(s) and secure with Faucet Retainer and Nut. DO NOT REMOVE GSKET FUET RETINER FUET FUET GSKET Install Faucet with O-ring into the center hole in deck or lavatory 1-/16" (0 mm) min. hole required. Note: If installing the Faucet on a three () hole sink, a Trim Plate should be installed at this time. ENTER HOLE IN DEK OR LVTORY FUET RETINER FLEX HOSE MODELS POWERED Y PLUG-IN TRNSFORMER ONLY DO NOT pull or crimp Power Line. Install Strainer and Flex Hose onto Supply Stop. Open Supply Stops. IMPORTNT: Flush dirt, debris, and sediment from Supply Line(s) before onnecting Flex Hoses. EF-100 Models: Plug Transformer into receptacle. ll Models: Remove label from Sensor. Install Strainer and Flex Hose onto Supply Stop. FLEX HOSE TRNSFORMER STRINER SENSOR LEL Transformer must be within of Faucet. Tighten the Flex Hose (with Strainer in place) securely to the Supply. LINE/STOP Electrical onnection for up to Six (6) Faucets Using One (1) Transformer 6 VD PLUG-IN TRNSFORMER Open Supply Stop(s). DISY HIN ELETRIL LE DISY HIN ELETRIL LE DISY HIN ELETRIL LE TO DDITIONL FUETS (6 MX.)

3 5 ctivate Faucet. 6 Set and Fix Temperature. ctivate faucet by pressing the button one (1) time, then immediately step away. Faucet will run for four () seconds and the range will automatically adjust to it s environment. Wait ten (10) seconds after water shuts off before using Faucet. I MODELS STNDRD MODELS djust Lever to set temperature. Optional To fix temperature, set lever to the desired position, then remove lever and plug hole with ap. ctivate Faucet and check for leaks. If Faucet does not function, refer to the Troubleshooting section of this instruction manual. Manual Range djustment Note: use Manual Range djustment only when desired range cannot be obtained with uto Range djustment in Step 5. Push button two () times (double click). Push and hold button in as Faucet continuously cycles through the following five (5) range settings. Push again for five (5) seconds until LED flashes four () times, then release button and wait five (5) seconds. D One (1) flash = longest range Two () flashes = long range Three () flashes = medium range Four () flashes = short range Five (5) flashes = shortest range Release button at desired setting. Then water will flow for four () seconds signaling confirmation of setting. Wait an additional ten (10) seconds before using Faucet.

4 dditional Features -lick FETURE & SETTINGS The i.q.-lick feature is a button on the underside of the Faucet spout that allows the user to place the Faucet into the following function modes: ontinuous Run, Temporary Off, Permanent Off and uto Set Range djustment. ontinuous Run Water flows from 1-0 minutes constantly for easy filling of sink, pail or for hygienic handwashing. Default setting is two () minute run time. Temporary OFF Water flow is deactivated up to two () minutes for convenient cleaning of sink and faucet. Permanent OFF The faucet is totally deactivated for safety and energy saving reasons during long absence. uto Set Range djustment ll Faucets feature the uto Set function. The detection area is automatically adapted to the sink where the Faucet is installed and this occurs upon initial power up. Thus reflection is prevented and a maximum of user convenience provided. Function Press utton LED Signal ontinuous Run minute default setting (adjustable from 1 time for seconds 5 short flashes 1-0 minutes) 1 time or will reset automatically after minutes Temporary Off times (double click) 5 short flashes followed by periodic flashing 1 time or will reset automatically after minutes Permanent Off onsult Factory Periodic flashing and then long flashes 1 time uto Set Range djustment times (double click) and then 1 time for 5 seconds 5 short flashes followed by short flashes Operation s the user's hands enter the beam's effective range, the beam is reflected back into the sensor receiver and activates the solenoid valve allowing water to flow from the Faucet. Water will flow until the hands are removed or until the Faucet reaches its automatic time out limit setting. are and leaning of hrome and Special Finishes DO NOT use abrasive or chemical cleaners (including chlorine bleach) to clean Faucets that may dull the luster and attack the chrome or special decorative finishes. Use ONLY mild soap and water, then wipe dry with clean cloth or towel. While cleaning the bathroom tile, protect the Faucet from any splattering of cleaner. cids and cleaning fluids will discolor or remove chrome plating. attery Replacement lose Supply Stop(s). D Insert a new 6 Volt Type R5 Lithium attery. The red LED will flash for one (1) minute. Reinstall attery over. Reconnect electrical lead Loosen Screw with hex wrench. Remove Throat Plate. Disconnect electrical lead at connector if required. at connector if previously disconnected. Reinstall Throat Plate. If LED doesn't flash or if it just lights up, remove and then reinsert the attery. If water flows continuously after inserting the new attery and opening the Supply Stops, remove and then reinsert the attery. Remove attery over using a No. 1 Phillips head screwdriver. Remove old attery and dispose of properly. E Open Supply Stop(s).

5 Troubleshooting Guide 1. Problem: Faucet does not function. ause: dhesive packaging label affixed over sensor eye. Solution: Remove adhesive label from sensor eye. ause: "Permanent Off" activated. Solution: Press button on Faucet throat one time.. Problem: Faucet delivers water in an uncontrolled manner. ause: Faucet is defective.. Problem: Faucet does not deliver any water when Sensor is activated. Indicator: Solenoid valve produces an audible "LIK." ause: Water supply stop(s) closed. Solution: Open water supply stop(s). ause: Water supply stop strainer(s) clogged. Solution: lean water supply stop strainer(s). Indicator: Solenoid valve DOES NOT produce an audible "LIK." ause: attery low (EF-150 Models). Solution: Replace battery (refer to attery Replacement on Page ). ause: Power failure (EF-100 Models). Solution: heck power supply.. Problem: Faucet delivers only a slow flow or dribble when Sensor is activated. ause: Water supply stop(s) are partially closed. Solution: ompletely open water supply stop(s). ause: Water supply stop strainer(s) clogged. Solution: Remove, clean, and reinstall water supply stop strainer(s). Replace strainer(s) if required. ause: erator is clogged. Solution: Remove, clean, and reinstall erator. Replace erator if required. ause: Faucet is defective. 5. Problem: Faucet does not stop delivering water or continues to drip after user is no longer detected. ause: Faucet is defective. 6. Problem: LED indicator blinks when Faucet is in use. ause: attery low (EF-150 Models). Solution: Replace battery (refer to attery Replacement on Page ) 7. Problem: - lick doesn't function (-I models only) ause: utton is defective. 8. Problem: The water temperature is too hot or too cold on a Faucet connected to hot and cold supply lines. USE: Supply Stops are not adjusted properly. SOLUTION: djust Supply Stops. USE: For models with integral mixing valve - Mixing valve is set improperly for the water temperature desired. SOLUTION: Rotate mixing valve handle clockwise to decrease water temperature or counterclockwise to increase water temperature. PRTS LIST Item Part Description No. No. 1 EF-10. gpm (8. Lpm) erator Spray Head 1 EF gpm (1.9 Lpm) Spray Head EF-- Throat Plate ssembly (attery Models) EF-6- Throat Plate ssembly (Plug-in Transformer Models) EF-- Throat Plate ssembly with i.q. - lick (attery Models) D EF-7- Throat Plate ssembly with i.q. - lick (Plug-in Transformer Models) EF-1000 attery Replacement Kit EF-1 Faucet Mounting Kit 5 EF-9 Strainer (Filter) 6 EF-1001 Mixer Handle ssembly and artridge 6 EF-100 Handle Repair Kit 7 EF-11 Transformer 8 EF- Solenoid Valve 9 EF " (0 mm) Flexible Supply Hose 10 EF-- Splitter able 11 EF /16 (00 mm) Extension able EF-5-7-1/ (100 mm) Extension able EF (00 mm) Extension able 1 ETF-607- Trim Plate for " enterset Sink 1 ETF-608- Trim Plate for 8" enterset Sink The information contained in this document is subject to change without notice When assistance is required, please contact Sloan Valve ompany Installation Engineering Department at: SLON-1 ( ) OR SLON VLVE OMPNY Seymour venue Franklin Park, IL 6011 Phone: VLVE-9 or Fax: or opyright 006 SLON VLVE OMPNY Printed 11-06