CPWR - The Center for Construction Research and Training 40-Hour Site Worker Post-Test Version XII
|
|
- Violet Brooks
- 6 years ago
- Views:
Transcription
1 CPWR - The Center for Construction Research and Training 40-Hour Site Worker Post-Test Place your answers on the separate answer sheet. 1.When must a worker, who is required to wear a respirator, perform a user seal check? A. Once a week B. Before each use C. Every other day D. Every month 2.Which set of symptoms are the result of heat stroke? A. Coma; strong rapid pulse; nausea; red hot skin B. Dizziness, nausea; heavy sweating; fainting; pale, cool skin C. Muscle spasm; pain in body parts D. Heat rash; sweating 3.Which of the following exposure limits or guidelines is the OSHA legally enforceable standard? A. Recommended Exposure Limit (REL) B. Threshold Limit Value (TLV) C. Permissible Exposure Limit (PEL) D. Maximum Exposure Limit (MEL) 4.Overall, what are the main types of hazards found on a hazardous waste site? A. Highway traffic and chemical exposure hazards B. Hazardous chemicals or materials and safety hazards C. Electrical and safety hazards D. Fires and dust 5.Laboratory sampling results of an unknown liquid reveal a ph of 2. This liquid would be classified as a. A. Acid B. Halogen C. Base D. Neutral 1
2 6.What does the yellow diamond stand for in the NFPA 704 labeling system? A. Health hazard B. Flammability hazard C. Special hazard D. Instability hazard 7.Which term most accurately describes all respirators? A. They leak B. They leak only if not fitted properly C. They protect against oxygen deficiency D. They protect against radionuclides 8.Which of the following zones is considered most contaminated? A. CRC B. Decontamination Zone C. CRZ D. Exclusion Zone 9.What protection factor has been assigned by OSHA to a full face Powered Air Purifying Respirator (PAPR)? A. 10 APF B. 50 APF C. 1,000 APF D. 10,000 APF 10. The combustible gas indicator is used to measure which of the following materials? A. Radiation B. Organic gases and vapors C. Flammable materials D. Oxygen concentration 2
3 11. Which member of the confined space entry team must remain at the entry point until the job is terminated or they are relieved? A. Entrant B. Attendant C. Entry Supervisor D. Rescue Personnel 12. What factor(s) can limit the use of chemical resistant clothing? A. All of the following B. It can be degraded by water. C. It can loose flexibility in cold weather. D. It can be degraded by strong acids and bases. 13. If you believe that you have been punished for exercising your OSHA rights, how long do you have, from the time you find out you've been punished, to contact OSHA to straighten out the problem? A. 2 days B. 10 days C. 14 days D. 30 days 14. At a minimum, how many days of on-site supervised actual field experience are required when you start work at a hazardous waste site? A. 1 B. 2 C. 3 D Who is required to pay for medical exams for workers at hazardous waste sites? A. The Worker B. The Union C. The worker's insurance D. The employer 16. If you are working on a hazardous waste site, how often are you required to take a hazardous waste refresher? A. 6 months B. 12 months C. 15 months D. 3 years 3
4 17. What term is used to identify the lowest concentration of a vapor or gas that will produce a flash of fire when an ignition source is present? A. LEL B. UFL C. Flammable Range D. Flashpoint 18. Which of the following is NOT considered an engineering controls. A. Automatic shut-off valves B. Local ventilation booths C. Personal protective equipment D. Negative pressure containment set-up 19. Which set of personal protective equipment represents at least part of Level C protection? A. SCBA and fully encapsulated chemical resistant suit B. General work clothing and hard hat C. Air purifying respirator, chemical resistant clothing, boots, and gloves D. Neoprene splash suit and Supplied Air Respirator 20. What is the primary purpose of most monitoring and sampling efforts? A. Determine the type and concentration of hazardous substances B. Obtain samples to send to EPA C. Find out if the drum is structurally sound D. Determine the background readings of hazardous substances 21. Which is the most accurate statement about the decontamination procedure? A. Remove the most grossly contaminated clothing first B. Perform decontamination as fast as possible C. Perform decontamination only if you are NOT going back into the Exclusion Zone D. Use water to decon oil based contamination 22. If you find a drum on-site with a radioactive label that has been crossed out with a black marker, which one of the following should you do first? A. Handle the drum as far away from your body as you can B. Handle the drum as if it were a normal drum C. Evacuate the area and report the situation to the safety officer D. Use mechanical equipment to move the drum 4
5 23. A new chemical is delivered to your work site from the manufacturer. You are asked to use it. Therefore, you want to know what it is; how to handle it; and what precautions to take. Which of the following gives you the most information about the chemical? A. The container label B. The Safety Data Sheet C. The employer's written hazard communication program D. The local OSHA office 24. You are working on a hot day (90 F) with a material that has a boiling point of 50 F. What does this mean to you? A. The material will settle in low areas displacing oxygen B. The material will explode C. The material will corrode D. The material will evaporate quickly 25. Which statement is always true of the "buddy system"? A. Is only needed at sites where the hazards are not known B. Visual or radio communication with the command post supervisor is not needed when using the buddy system C. Must always be used when working in the Exclusion Zone D. Allows workers to enter the Exclusion Zone from different points and then work together 26. Which of the following is the most common route of entry into your body for carbon monoxide? A. Contact B. Inhalation C. Ingestion D. Injection 27. What is the primary purpose of the Site Specific Health and Safety Plan? A. Protect contractor in case of lawsuit B. Meet EPA and OSHA requirements C. Provides the site safety and health information and protective procedures D. Resolve disputes among workers 28. The main purpose of personal monitoring devices, is to measure the to physical and chemical agents. A. worker s exposure B. community s exposure C. environment s exposure D. public s exposure 5
6 29. Time Weighted Average (TWA) is the average concentration of material over a full work shift. What is the TWA for the following worker's exposure to toluene? A. 50 ppm B. 100 ppm C. 60 ppm D. 150 ppm 75 ppm for 2 hours, 100 ppm for 1 hour, and 30 ppm for 5 hours 30. Control of run-off generated during decontamination is: A. A low priority because chemicals are diluted with water. B. A low priority unless the chemical is water reactive. C. A low priority unless the site is near a community. D. Never a low priority 31. Which of the following are included in an emergency response plan that meets OSHA 29CFR requirements? A. The location of safe refuge for evacuated site workers B. SOPs for shutting down equipment on the site C. Survivor benefit plan D. Both A and B 32. Which of the following statements about SOPs is correct? A. Workers only need training on SOPs if the chemicals are explosive. B. Workers are responsible for choosing the level of PPE C. SOPs are needed for routine, everyday work activities. D. Only level D protection is needed in most decon lines. 33. Say you used a detector tube to measure the level of toluene in the atmosphere and found it to be 100 ppm. Given the usual accuracy of detector tubes, how far off could the reading be? A. +/- 25 ppm B. +/- 10 ppm C. +/- 15 ppm D. +/- 20 ppm 34. An example of a reaction to a chronic exposure is: A. Skin burns from an acid splash. B. Collapse from lack of oxygen in a confined space. C. Lung scarring after years of working with asbestos. D. Dizziness from inhaling solvent vapors. 6
7 35. What federal agency is responsible for hazardous waste worker safety? A. NIOSH (National Institute for Occupational Safety and Health) B. OSHA (Occupational Safety and Health Administration) C. EPA (Environmental Protection Agency) D. DOT (Department of Transportation) 36. What action is required when the warning device on your SCBA (Self Contained Breathing Apparatus) sounds? A. Switch SCBA to bypass air and continue working B. Put work in order, notify buddy, leave through emergency decon area. C. Stop what you are doing, notify buddy, leave through decon area D. Drop your work tools, leave area, and go to emergency decon area 37. When dressed out in Level A or Level B protection, which of the following is NOT likely to be a problem? A. Difficulty communicating with a buddy B. Increased risk of heat stress C. Inhalation of toxic gases D. Increased risk of accidents because of limited mobility 38. Sampling can be classified as: A. Personal, aggregate and bulk/surface B. Group, area and bulk/surface C. Personal, area and laboratory D. Personal, area and bulk/surface 39. Which of the following types of information must be included in the site specific safety and health plan? A. Standard operating procedures B. Company organizational chart C. Health, welfare, and accident benefits plan D. Paper work requirements of company 40. Which statement best explains what happens to the results of medical exams? A. Employers get a copy of all medical test s results from the doctor, even those not related to your work B. Workers get a written opinion directly from the doctor C. Workers will always get a copy of all medical test s results from the employer D. Employers get the written opinion from the doctor; workers get a copy from the employer 7
8 41. Which of the following conditions is an indication that it is time to change the cartridge in your APR? A. All of the below are indications that it is time to change cartridges. B. When the ESLI (End of Service Life Indicator) code on the cartridge changes color while in the Hot Zone. C. When the cartridge change schedule tells you to change. D. When you detect a different smell in your respirator while in the Hot Zone. 42. If a worker discovers an unsafe or unhealthy condition in the workplace, the worker should: A. Inform his/her supervisor. B. Keep quiet and avoid the area. C. Attempt to hide the condition by placing plywood or other substances over the hazard. D. Immediately contact his/her lawyer. 43. Which phrase tells you that above this concentration the material is too Arich@ to ignite? A. Below the Threshold Limit Value (TLV) B. Above the Upper Explosive Level (UEL) C. Below the Permissible Exposure Limit (PEL) D. Below the Specific Gravity (SpGr) 44. Which statement meets the requirements of an Emergency Response Plan (ERP)? A. Workers can see the ERP only if they ask for it. B. Workers must have regular drills on the ERP. C. Workers only have to read the ERP. D. Workers must pass a written test on the ERP. 45. Using a lock-out in a confined space means: A. Prohibiting workers from entering the work area. B. Physically preventing a release of energy and material into the space C. Separating the workers from the hazards D. Using engineering controls 46. The OSHA Assigned Protection Factor of a half-face mask is 10. The OSHA PEL for Nitric Acid is 2 ppm. What is the Maximum Use Concentration? A. 20 ppm B. 12 ppm C. 8 ppm D. 25 ppm 8
9 47. A container has ruptured, and a chemical has spilled. The SDS indicates that the chemical has a PEL of 2ppm. It is not absorbed through the skin. What is the lowest level of protection that should be worn? A. Level A B. Level B C. Level C D. Level D 48. The site safety officer says your gloves are having a Apermeation problem@. What does this mean? A. The glove is too thick. B. The glove has not been properly decontaminated. C. The cuff is not tight enough to keep chemicals from leaking in. D. The glove allows chemicals to pass through it quickly and easily. 49. When working in low lying places where a gas or vapor is present, what property is of greatest concern? A. Boiling point B. Melting point C. Specific gravity D. Vapor density 50. What source of information is most often used first by emergency first responders at the scene of an hazardous materials incident? A. Wireless Information System for Emergency Responders (WISER) B. Code of Federal Regulations (CFR) C. NIOSH Pocket Guide D. National Contingency Plan 9
Teamsters Hazardous Waste Worker Training Initial Hazardous Waste Site Worker Course
Teamsters Hazardous Waste Worker Training Initial Hazardous Waste Site Worker Course Post-Test Test Booklet International Brotherhood of Teamsters Worker Training Program 1. Which agency makes regulations
More informationMATERIAL SAFETY DATA SHEET. COPPER CARE PRODUCT NAME: Aqua-Nap-5. ATTENTION: SAFETY MANAGER MSDS Number: Date of Last Revision: 04/10/2006
ATTENTION: SAFETY MANAGER MSDS Number: Date of Last Revision: 04/10/2006 A. PRODUCT INFORMATION Product Code: Waterborne Copper Naphthenate / Common Name/Synonyms: Naphthenic Acid, Copper Salt Chemical
More informationMidwest Consortium 8HR Modular Exam Inspect/Don/Doff
8HR Modular Exam Inspect/Don/Doff 1. Important reasons to inspect respirators include: A. All of the following B. Make sure the elastic parts are still stretchy C. Valves have not been removed or damaged
More informationSouthern Lithoplate, Inc. P.O. Box 9400 Wake Forest, NC Phone: Fax: Website:
Southern Lithoplate, Inc. P.O. Box 9400 Wake Forest, NC 27588 Phone: 800-638-7990 Fax: 919-554-0786 Website: www.slp.com SECTION I - PRODUCT IDENTIFICATION Product Name: SLP Thermal Deletion Pen Product
More informationTEMPLE UNIVERSITY ENVIRONMENTAL HEALTH AND RADIATION SAFETY
Purpose In accordance with applicable regulations and Temple University, this policy was developed to minimize exposure to glutaraldehyde. Applicability This policy is applicable to all Temple University
More informationTEMPLE UNIVERSITY ENVIRONMENTAL HEALTH AND RADIATION SAFETY
Page 1 of 9 ISSUED: 5/00 REVISED: 08/06 Introduction Purpose: In accordance with applicable regulations and Temple University, this policy was developed to minimize exposure to Ethylene Oxide. Applicability
More information1. PRODUCT IDENTIFICATION 2. COMPOSITION / INFORMATION ON HAZARDOUS INGREDIENTS
OPTI Medical Systems, Inc. 235 Hembree Park Drive Roswell, GA 30076 USA Tel: +1 770 510 4444 +1 800 490 OPTI Fax: +1 770 510 4445 1. PRODUCT IDENTIFICATION Product Name: ASSY, 28 psi Gas Bottle Information
More informationSAFETY DATA SHEET (SDS)
1. PRODUCT AND COMPANY IDENTIFICATION 1.1 Product Name: Part Number: CAS-No.: SDS Number: 1.2 Recommended Use: Colloidal Iron Stock 10365 Not applicable 2540 Laboratory Chemicals 1.3 Company: Newcomer
More informationTeamsters Hazardous Waste Worker Training Initial Hazardous Waste Site Worker Course
Teamsters Hazardous Waste Worker Training Initial Hazardous Waste Site Worker Course Pre-Test Test Booklet International Brotherhood of Teamsters Worker Training Program a. How many weeks did you work
More informationHazMat Awareness and Operations Study Guide.
HazMat Awareness and Operations Study Guide. 1. Define a hazardous material. 2. Describe the different levels of hazardous materials training: awareness, operations, technician, and specialist. 3. Understand
More informationConcordia College Moorhead, Minn.
Concordia College Moorhead, Minn. Title: Employee Right-to-Know/Hazard Communication Effective: 8-20-97; 6-19-00 ; 8-1-03; 8-6-07 Purpose: Concordia College is firmly committed to providing all its employees
More informationHazard Communication Program. San José State University
San José State University One Washington Square San José, California Facilities Development and Operations Department July 11, 2012 Page intentionally left blank SJSU_Hazard Communication Program_2012-0711.docx
More informationSAFETY DATA SHEET FOR FALK GMAX 6000
Product Name: G MAX 6000 Product Code: 425065 Trade Name: Industrial Oil Benz Oil Company 2724 W. Hampton Ave. Milwaukee, WI 53209 Telephone Numbers During normal business hours call (44)442-2900 Outside
More informationHAZARDOUS INCIDENT SITE SAFETY PLAN
HAZARDOUS INCIDENT SITE SAFETY PLAN NOTE: A site-specific Site Safety Plan must be developed and implemented for each site where investigators may potentially be exposed to hazardous substances while conducting
More informationSafety Data Sheet. Address GHS Precautions If skin irritation occurs: Get medical advice/attention
Safety Data Sheet Section - Product and Company Identification Product Name: WHITE SOL Product Code: 465020 Trade Name: Industrial Lubricant Benz Oil Company 2724 W. Hampton Ave. Milwaukee, WI 53209 Telephone
More informationALBUQUERQUE PUBLIC SCHOOLS RESPIRATORY PROTECTION PROGRAM
ALBUQUERQUE PUBLIC SCHOOLS RESPIRATORY PROTECTION PROGRAM Risk Management Department August, 2008 ALBUQUERQUE PUBLIC SCHOOLS RISK MANAGEMENT DEPARTMENT RESPIRATORY PROTECTION PROGRAM TABLE OF CONTENTS
More informationSAFETY DATA SHEET PRODUCT NAME Sulfur hexafluoride 1.2 RELEVANT IDENTIFIED USES OF THE SUBSTANCE OR MIXTURE AND USES ADVISED AGAINST :
SULFUR HEXAFLUORIDE PAGE NO. 1 of 10 1 PRODUCT AND COMPANY IDENTIFICATION 1.1 PRODUCT IDENTIFIER : 1.1.1 PRODUCT NAME Sulfur hexafluoride 1.1.2 SYNONYMS Sulfur fluoride (SF6), (OC-6-11)-; Sulfur fluoride
More informationMATERIAL SAFETY DATA SHEET
MATERIAL SAFETY DATA SHEET SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT: M-Line Rosin Solvent November 22, 2005 Vishay Micro-Measurements Post Office Box 27777 Raleigh, NC 27611 919-365-3800
More informationLUSTER SEAL WB 150 Version 3.0 Print Date 07/08/2012 REVISION DATE: 07/07/2012
SECTION 1 - PRODUCT IDENTIFICATION / PREPARATION INFORMATION Product Information Trade name : Product code : THWB150555 Supplier : Euclid Canada 2835 Grande-Allée St-Hubert, QC J4T 2R4 Telephone : 1-800-667-0920
More informationMidwest Consortium 40-Hour Technician Posttest Version 2 Answer Key
Midwest Consortium 40-Hour Technician Posttest Version 2 Answer Key ID No. (office use only) Name b. 1. An example of an acute health effect is: a. lung cancer b. burning eyes c. sterility d. arthritis
More information1. Product and Company Identification. Glen-Pak 50mg DNA Purification Cartridge
Product Code: Product Name: Product Use: Manufacturer Information Company Name: 1. Product and Company Identification 60-5000-xx For Research Use Only Glen Research LLC 22825 Davis Drive Sterling, VA 20164
More informationMATERIAL SAFETY DATA SHEET
MATERIAL SAFETY DATA SHEET 24 Madison Road, Fairfield, New Jersey 07004, USA MANUFACTURER: JEEN INTERNATIONAL CORPORATION 24 MADISON ROAD FAIRFIELD, NJ 07004 Telephone # 973-439-1401 Chemtrec Emergency
More informationSafety Data Sheet EPI-CLENZ FOAMING INSTANT HAND SANITIZERS
Safety Data Sheet EPI-CLENZ FOAMING INSTANT HAND SANITIZERS Section 1. Identification Product Identifier Synonyms Manufacturer Stock Numbers Recommended use Uses advised against Manufacturer Contact Address
More informationItem #: RS4601-B. Restrictions on Use: Any use other than specified. In Case of Emergency: Chemtrec US
1. Identification Product Name: Decalcifier - Formic Synonyms: N/A Recommended Use: Laboratory Reagent Supplier: Avantik Biogroup 32 Commerce Street Springfield, NJ 07081 (800) 1-888-392-8411 783-9424
More informationHAZARDOUS MATERIALS OPERATIONS NFPA 472, 2008 Edition
5.2 Core Competencies Analyzing the Incident JPR - HMO #1 5.2.1 Surveying the Hazardous Materials/WMD Incidents Revised: June 30, 2011 Standard Area: Competencies Analyzing the Incident STANDARD: 5.2.1.3.2
More informationMATERIAL SAFETY DATA SHEET
MATERIAL SAFETY DATA SHEET SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT: M-Bond 200 Catalyst C May 7, 2013 Vishay Measurements Group, Inc. Post Office Box 27777 Raleigh, NC 27611 919-365-3800
More informationTAMMSCURE WB 30C Version 3.0 Print Date 07/08/2012 REVISION DATE: 07/07/2012
SECTION 1 - PRODUCT IDENTIFICATION / PREPARATION INFORMATION Product Information Trade name : Product code : THH3WBD55 Supplier : Euclid Canada 2835 Grande-Allée St-Hubert, QC J4T 2R4 Telephone : 1-800-667-0920
More informationToluidine Blue, 1% Avantik 36 Commerce Street Springfield, NJ Tel: Fax: Page 1/5
1. Identification Product Name: Item #: SKC1082-250, SKC1082-500 Web SDS: S216 Synonyms: N/A Recommended Use: Special Stains Restrictions on Use: N/A Manufacturer: BBC Biochemical 409 Eleanor Lane Mount
More informationSDS SAFETY DATA SHEET
SDS SAFETY DATA SHEET 1. Identification Product identifier: 468 mv ORP Calibration Solution Synonyms: ORP 468 Calibration Solution Chemical Formula: N/A (Inorganic Salt) Recommended and Restriction Use
More informationEMA, Inc. SITE SAFETY PLAN
EMA, Inc. SITE SAFETY PLAN A. SITE DESCRIPTION JOB NAME: JOB NUMBER: DATE: PLAN REVISION NUMBER: SITE ADDRESS: Additional Site / Project Information: B. SCOPE OF WORK 1. 2. 3. 4. 5. 6. C. ONSITE ORGANIZATION
More informationSAFETY DATA SHEET (SDS)
1. PRODUCT AND COMPANY IDENTIFICATION 1.1 Product Name: Part Number: CAS-No.: SDS Number: 1.2 Recommended Use: Citrate Buffer 0.01M, ph 6.0 10355 Not applicable 2530 Laboratory Chemicals 1.3 Company: Newcomer
More informationM a t e r i a l S a f e t y D a t a S h e e t
Page 1 of 5 SECTION #1 PRODUCT AND COMPANY IDENTIFICATION Product: Phoenix Brands Consumer Service Telephone Number: 1-866-794-0800 2855 N. Franklin Rd., #7 Emergency Contact: PROSAR IPC Indianapolis,
More information1. PRODUCT IDENTIFICATION 2. COMPOSITION / INFORMATION ON HAZARDOUS INGREDIENTS
OPTI Medical Systems Inc. 235 Hembree Park Drive Roswell, GA 30076 USA Tel: +1 770 510 4444 +1 800 490 6784 Fax: +1 770 510 4445 1. PRODUCT IDENTIFICATION Product Name: OPTI CCA Cassette Information Number:
More informationSAFETY DATA SHEET According to GHS
Section 1: Identification Product Identifier Trade Name: Chemical Name: Recommended Use: Restrictions on Use: B-12-008 Polyurethane Resin Component for the manufacture of Polyurethanes Chemical Manufacturer
More informationGHS SAFETY DATA SHEET (SDS) SECTION 1 PRODUCT AND COMPANY IDENTIFICATION SECTION 2 HAZARDS IDENTIFICATION
GHS SAFETY DATA SHEET (SDS) SECTION 1 PRODUCT AND COMPANY IDENTIFICATION PRODUCT: Part #624 MIX AND POUR FOAM (Side B) FIBRE GLAST DEVELOPMENTS CORP. 385 CARR DRIVE BROOKVILLE, OH 45309 TELEPHONE: (937)
More informationProduct Name:Heat Sink Compound 1801 Morgan Street MSDS Number:148
Section 4 - Fire & Explosion Hazard Data Flash Point (method): Flammable Limits-LEL: Flammable Limits-UEL: Extinguishing Agents: Fire Fighting Procedures and Equipment: Decomposition Products May Include:
More information: CHEMTREC (in US); CHEMTREC (International and Maritime)
Revision date: 03/10/2015 Date of issue: 03/10/2015 Version: 2.0 SECTION 1: Identification 1.1. Product identifier Product form : Substance Substance name : MED-361 @ 350 cp CAS No : 63148-62-9 Synonyms
More informationSafety Data Sheet SUREPREP NO-STING SKIN PROTECTANT
Safety Data Sheet SUREPREP NO-STING SKIN PROTECTANT Section 1. Identification Product Identifier Synonyms Manufacturer Stock Numbers Recommended use Uses advised against Manufacturer Contact Address SUREPREP
More informationSAFETY DATA SHEET MATERIAL AND MANUFACTURER IDENTIFICATION HAZARD(S) INDENTIFICATION. Product Name: Odor Zyme Revision Date: 5/19/2015
Revision Date: 5/19/2015 SAFETY DATA SHEET SECTION 1 MATERIAL AND MANUFACTURER IDENTIFICATION PRODUCT Product Identifier: Odor Zyme Intended Product Use: Deodorizer/Odor Control Manufacturer Identification
More informationPurpose Written Program Hazard Classifications (GHS) SDS Sheets (GHS) Labels (GHS) Employee Training Chemical Safety Questions
Purpose Written Program Hazard Classifications (GHS) SDS Sheets (GHS) Labels (GHS) Employee Training Chemical Safety Questions Rights Reserved. 2 Purpose: Ensure that the hazards of all chemicals produced
More informationSAFETY DATA SHEET Pet Stain and Odor Eliminator. 1. Product and Company Identification. 2. Hazards Identification
Product Code: Product Name: Company Name: Web site address: SAFETY DATA SHEET 1. Product and Company Identification 916 SUNBELT LABORATORIES P.O. BOX 1563 STAFFORD, TX 77497 www.sunbelt-labs.com Phone
More informationSafety Data Sheet. TB Quat
Section 1 Identification Trade Name: Product Identification: Synonyms: Product Use Description: RTU disinfectant cleaner General Info Phone: (800) 795-922 6537 Emergency Phone: (800) 535-5053 Water-based
More informationSAFETY DATA SHEET Lead Stop
SAFETY DATA SHEET Lead Stop SECTION 1 Identification Product Name: Lead Stop SDS Number: DCI-061 TiO2 Recommended use: Paint Stripping. Restrictions on use: Use only as directed Manufactured for: DUMOND
More informationVersion 3.0 Print Date 07/08/2012 REVISION DATE: 07/07/2012 SECTION 1 - PRODUCT IDENTIFICATION / PREPARATION INFORMATION
SECTION 1 - PRODUCT IDENTIFICATION / PREPARATION INFORMATION Product Information Trade name : Product code : 79T 27 Supplier : Euclid Canada 2835 Grande-Allée St-Hubert, QC J4T 2R4 Telephone : 1-800-667-0920
More information1. Chemical Product and Company Identification
My Gas Material Safety Data Sheet 1. Chemical Product and Company Identification Product Name: Carbon Dioxide, Solid or Dry Ice Other means of identification: Dry ice (nuggets, pellets or blocks) carbonice,
More information19Feb2016 EN (English US) 1/5
Akt Calibrator, Calibrator 1, Calibrator 2, Calibrator 3, Calibrator 4, Calibrator 5, Calibrator 6, Calibrator 7, Calibrator 8, CHO Host Cell Protein Calibrator, CRP Calibrator, GLP-1 (7-36)amide Calibrator
More informationSafety Data Sheet PERMA SEAL
Section 1 Identification Trade Name: Perma Seal General Info Phone: (770) 424-7550 Product Identification: 5280 Emergency Phone: (800) 255-3924 Synonyms: Polymer emulsion Product Use Description: Floor
More informationKUREZ DR VOX Version 3. Print Date 05/20/2009 REVISION DATE: 05/19/2009
SECTION 1 - PRODUCT IDENTIFICATION / PREPARATION INFORMATION Product Information Trade name : Product code : 157D 55 Supplier : Euclid Canada 2835 Grande-Allée St-Hubert, QC J4T 2R4 Telephone : 1-800-667-0920
More information12/14/2017 EN (English US) 1/5
According To Federal Register / Vol. 77, No. 58 / Monday, March 26, 2012 / Rules And Regulations And According To The Hazardous Products Regulation (February 11, 2015). Date of Issue: 12/14/2017 Version:
More informationSafety Data Sheet. Address
Safety Data Sheet Section 1 - Product and Company Identification Product Name: WHITE SOL Product Code: 465020 Trade Name: Industrial Lubricant Benz Oil Company 2724 W. Hampton Ave. Milwaukee, WI 53209
More informationEmergency Phone: (800) Detergent with bacteria Supplier: ENVIRO CHEMICAL INC AURORA ROAD SOLON, OH 44139
Section 1 Identification Trade Name: Product Identification: Synonyms: Product Use Description: Drain maintainer and odor control General Info Phone: (440) 287-2200 20596 Emergency Phone: (800) 535-5053
More informationMATERIAL SAFETY DATA SHEET
MATERIAL SAFETY DATA SHEET SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION PRODUCT: M-Bond Curing Agent - Type 15 April 13, 2010 Vishay Measurements Group, Inc. Post Office Box 27777 Raleigh, NC
More informationRespiratory Protection
Respiratory Protection Purpose The purpose is to establish a set of guidelines for the selection of respiratory protection equipment, situations for its use, and training in the use of the respirator required.
More informationSafety Data Sheet. AK Page 1 of 6 January 01, Appearance/Odor: Thick, viscous, white to off-white liquid with a mild ammonia odor
AK 40.00 Page 1 of 6 Section 1: PRODUCT AND COMPANY IDENTIFICATION Omega Products International P.O. Box 77220 Corona, CA 92877-0107 Company Phone Number: 1-951-737-7447 Emergency Phone Number: 1-951-737-7447
More informationMaterial Safety Data Sheet
Material Safety Data Sheet 1. Product and Company Identification Product name Chemical formula Synonyms Company : : N-O : Nitrogen Oxide (NO); (NO); Trimer; Nitrogen Monoxide; Nitrogen Monooxide; Nitrogen
More information1. Product And Company Identification
1. Product And Company Identification Product Name: Responsible Party: HYB-2 Information Phone Number: +1 203-205-2900 Emergency Phone Number: For Medical Emergencies, call 1-866-949-6465 / +1 303-389-1332
More informationE3628 THE RESPIRATORY PROTECTION PROGRAM: EMPLOYEE TRAINING. Leader s Guide ERI Safety Videos EMPLOYEE TRAINING
E3628 THE RESPIRATORY PROTECTION PROGRAM: EMPLOYEE TRAINING Leader s Guide 2007 ERI Safety Videos THE RESPIRATORY PROTECTION PROGRAM: EMPLOYEE TRAINING This easy-to-use Leader s Guide is provided to assist
More informationINTRODUCTION UNIFIED COMMAND
INTRODUCTION The Hazardous Materials organizational module is designed to provide an organizational structure that will provide necessary supervision and control for the essential functions required at
More informationSafety Data Sheet MEDSPA BABY BATH
Safety Data Sheet MEDSPA BABY BATH Section 1. Identification Product Identifier Synonyms Manufacturer Stock Numbers Recommended use Uses advised against Manufacturer Contact Address MEDSPA BABY BATH MSC095042;
More informationPLASTOL SPC - BULK GALLONS Version 3.1 Print Date 01/20/2015 REVISION DATE: 06/20/2013
SECTION 1 - PRODUCT IDENTIFICATION Trade name : Product code : 704 99 COMPANY : Euclid Chemical Company 19218 Redwood Road Cleveland, OH 44110 Telephone : 1-800-321-7628 Emergency Phone: : U.S. only: 1-800-424-9300
More informationUse only for the purpose on the product label.
SAFETY DATA SHEET SOLID SANITIZER Section 1. Chemical product and company identification Product name Recommended use and restrictions SOLID SANITIZER Sanitizer. Use only for the purpose on the product
More informationIDQ Operating, Inc. 44 Old Ridgebury Road Suite 300 Danbury, CT Tel Product And Company Identification
1. Product And Company Identification Product Name: IDQ 374 Responsible Party: Information Phone Number: +1 203-205-2900 Emergency Phone Number: For Medical Emergencies, call 1-866-949-6465 / +1 303-389-1332
More informationSafety Data Sheet EPI-CLENZ PLUS INSTANT HAND SANITIZERS
Safety Data Sheet EPI-CLENZ PLUS INSTANT HAND SANITIZERS Section 1. Identification Product Identifier Synonyms Manufacturer Stock Numbers Recommended use Uses advised against Manufacturer Contact Address
More information3. Fire And Explosion Hazard Data FLASH POINT: Not determined. However the product is combustible. METHOD USED: Estimated from ingredients.
Page 1 of 5 1. Hazardous Ingredients Name CAS# OSHA PEL ACGHI-TLV OTHERS % Natural and Proprietary N.E. N.E. N.E > 5.0 Synthetic Wax Blend 64742-48-9 -- -- * 1200mg/m3 9.1 Isoparaffinic Hydrocarbon Water
More informationPersonal Protective Equipment 29 CFR 1926
Personal Protective Equipment 29 CFR 1926 OSHA- PPE http://www.osha.gov/publications/osha31 51.html NIOSH s Protective Clothing Web Page http://www.cdc.gov/niosh/npptl/topics/prot clothing/ 1926.95 PPE
More informationMATERIAL SAFETY DATA SHEET Organic Laundry Detergent
MATERIAL SAFETY DATA SHEET Organic Laundry Detergent SECTION 1 PRODUCT AND COMPANY IDENTIFICATION Product Name: Organic Laundry Detergent Effective Date: May 1, 2010 Manufacturer: Greenology Products,
More informationMATERIAL SAFETY DATA SHEET
MATERIAL SAFETY DATA SHEET 1 PRODUCT AND COMPANY IDENTIFICATION Product Name: Manufacturer Name: Federal-Mogul Corporation 26555 Northwestern Highway Southfield, Michigan 48034 U.S.A. Intended Use: Industrial
More informationSAFETY DATA SHEET Dry Foam Carpet Shampoo Concentrate. 1. Product and Company Identification. 2. Hazards Identification
Product Code: Product Name: Company Name: Web site address: SAFETY DATA SHEET 1. Product and Company Identification 348 SUNBELT LABORATORIES P.O. BOX 1563 STAFFORD, TX 77497 www.sunbelt-labs.com Phone
More informationKardol Quality Products 285 S. West Street Lebanon, Ohio Fax:
Kardol Quality Products 285 S. West Street Lebanon, Ohio 45036 513-933-8206 Fax: 513-932-6900 MATERIAL SAFETY DATA SHEET # 500121 Trade Name: Epoxy Glue Hardener Section 1: Material Identification Weight
More informationSECTION 2: HAZARDS IDENTIFICATION Classification of the Substance or Mixture GHS-US/CA Classification
SECTION 1: IDENTIFICATION Product Identifier Product Form: Mixture Product Name: Intended Use of the Product No use is specified. Name, Address, and Telephone of the Responsible Party Company Zeus Scientific,
More information: EUCON DUSTROL - BULK GALLONS
SECTION 1 - PRODUCT IDENTIFICATION Trade name : Product code : 011AD 99 COMPANY : Euclid Chemical Company 19218 Redwood Road Cleveland, OH 44110 Telephone : 1-800-321-7628 Emergency Phone : U.S. only:
More informationALPHAGUARD M-PRIME - 1 GALLON Version 1. Print Date 04/18/2012 REVISION DATE: 10/05/2011
SECTION 1 - PRODUCT IDENTIFICATION Trade name : Product code : 351680 801 COMPANY : Tremco Incorporated 3735 Green Road Cleveland, OH 44122 Telephone : (216) 292-5000 8:30-5:00 EST Emergency Phone: : (216)
More information05/21/2015 EN (English US) 1/5
Revision Date: 05/21/2015 Date of issue: 05/21/2015 Version: 1.0 SECTION 1: IDENTIFICATION 1.1. Product Identifier Product Form: Mixture Product Name: Gel Loading Buffer 10 Product Code: 4850-20-10 1.2.
More informationHealth & Safety Policy and Procedures Manual SECTION 34 HYDROGEN SULFIDE (H2S) PROGRAM
SECTION 34 HYDROGEN SULFIDE (H2S) PROGRAM 1. REGULATORY STANDARD: OSHA - 29 CFR 1910.1200 and 1926.55 Purpose: The purpose of this program is to inform interested persons, including employees, that Maul
More informationSAFETY DATA SHEET. 24 hour Transportation Emergency CHEMTREC 1020 Harts Lake Road
Page 1 of 5 SECTION 1: IDENTIFICATION Product: 1% Periodic Acid Product number: 874, 882A Synonyms: None Recommended use: Laboratory chemical Company Anatech Ltd 24 hour Transportation Emergency 800.424.9300
More informationIngredient CAS Number Percent Hazardous Peptone, Type >95 % No exposure limits established by OSHA or ACGIH
SAFETY DATA SHEET PhytoTechnology Laboratories 1. CHEMICAL IDENTIFICATION AND COMPANY INFORMATION PRODUCT NAME: Peptone, Type 1 PRODUCT NUMBER: COMPANY INFO: P775 EMERGENCY PHONE NUMBER: RECOMMENDED USE:
More informationSafety Data Sheet INFANT HEEL WARMERS
Safety Data Sheet INFANT HEEL WARMERS Section 1. Identification Product Identifier Synonyms Manufacturer Stock Numbers Recommended use Uses advised against Manufacturer Contact Address INFANT HEEL WARMERS
More information1. Product And Company Identification. (SDS for product manufactured after 7/1/2017.)
1. Product And Company Identification Product Name: Product Number: Responsible Party: A/C Pro Professional Formula A/C Recharge Ultra Synthetic R134a (SDS for product manufactured after 7/1/2017.) ACP-100V
More informationSAFETY DATA SHEET (SDS)
1. PRODUCT AND COMPANY IDENTIFICATION 1.1 Product Name: Part Number: CAS-No.: SDS Number: 1.2 Recommended Use: Sodium Borate 5%, Aqueous 13826 Not applicable 4310 Laboratory Chemicals 1.3 Company: Newcomer
More informationMATERIAL SAFTEY DATA SHEET
NAME OF PRODUCT: PROLINE COLORANTS MSDS DATE: 07/07/2010 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: Proline Colorants SYNONYMS: Emulsion PRODUCT CODES: XS-023 MANUFACTURER: ADDRESS: Xcel
More informationEUCON CIA - BULK GALLONS Version 2. Print Date 09/13/2008 REVISION DATE: 09/12/2008
SECTION 1 - PRODUCT IDENTIFICATION Trade name : Product code : 019C 99 COMPANY : Euclid Chemical Company 19218 Redwood Road Cleveland, OH 44110 Telephone : 1-800-321-7628 Emergency Phone: : U.S. only:
More informationMaterial Safety Data Sheet
Material Safety Data Sheet MSDS: 760 SECTION 1: CHEMICAL PRODUCT AND COMPANY INFORMATION Company: HAZARD RATING SCALE IDQ Operating, Inc. Health 1 0 = Insignificant 2901 W Kingsley Rd. Fire: 2 1 = Slight
More informationAST PENETRANT II SAFETY DATA SHEET Section 1- Product and Company Identification
AST PENETRANT II SAFETY DATA SHEET Section 1- Product and Company Identification Product Code: 17063 Manufacture/Supplier : Anti-Seize Technology 2345 N. 17 th Ave. Franklin Park, IL 60131 Phone: 847-455-2300
More informationSafety Data Sheet 0307 LYNX RTU QUAT CLEANER DISINFECTANT. Additional ID:
SECTION 1: Identification Trade Name: Product Identification: Synonyms: Product Use Description: Manufactured By: 6514 Water-based alkali detergent ABC COMPOUNDING CO., INC. PO BOX 80729 Conyers, GA 30013
More informationSAFETY DATA SHEET (SDS)
1. PRODUCT AND COMPANY IDENTIFICATION 1.1 Product : Part Number: : SDS Number: 1.2 Recommended Use: 1.3 Company: Newcomer Supply 2505 Parview Road Middleton, WI 53562 USA Telephone: 1-800-383-7799 Fax:
More informationSafety Data Sheet Lyden Oil Company
Page 1 of 8 1 PRODUCT AND COMPANY INFORMATION Product Name: Revision Date: 07/01/2018 Common Name: Synthetic Drawing and Stamping Fluid CAS Number: Blend Product Code: 807031 Synonyms: N/A Company Identification:
More informationSafety Data Sheet ATTACK Section 1 Identification. Section 2 Hazards Identification
Section 1 Identification Trade Name: General Info Phone: (770) 424-7550 Product Identification: 1995 Emergency Phone: (800) 255-3924 Synonyms: Water-based insecticide Product Use Description: Insect spray
More information: KUREZ W VOX - 55 GAL DRUM
SECTION 1 - PRODUCT IDENTIFICATION Trade name : Product code : 157W 55 COMPANY : Euclid Chemical Company 19218 Redwood Road Cleveland, OH 44110 Telephone : 1-800-321-7628 Emergency Phone: : U.S. only:
More informationMATERIAL SAFTEY DATA SHEET
NAME OF PRODUCT: AQUA EPOXY COAT MSDS DATE: 07/07/2010 SECTION 1: PRODUCT AND COMPANY IDENTIFICATION PRODUCT NAME: Aqua Epoxy Coat SYNONYMS: PRODUCT CODES: XS-011 MANUFACTURER: ADDRESS: Xcel Surfaces 3750
More informationCLEARSEAL WB 150 Version 2.0 Print Date 07/09/2012 REVISION DATE: 07/08/2012
SECTION 1 - PRODUCT IDENTIFICATION Trade name : Product code : THCWB150D55 COMPANY : Euclid Chemical Company 19218 Redwood Road Cleveland, OH 44110 Telephone : 1-800-321-7628 Emergency Phone: : U.S. only:
More informationSafety Data Sheet Lyden Oil Company
Page 1 of 8 1 PRODUCT AND COMPANY INFORMATION Product Name: Revision Date: 10/30/2015 Common Name: Synthetic gear oil 75W-90 CAS Number: Blend Product Code: 710301 Synonyms: Synthetic automotive gear oil
More information507 Rapid Set Cold Pothole Repair Material Safety Data Sheet
507 Rapid Set Cold Pothole Repair Material Safety Data Sheet means No Data Available Identity (As Used on Label and List) Note: Blank spaces are not permitted. It any item is 507 Rapid Set Cold Pothole
More informationHAZWOPER 8-Hr Refresher Aug. 20, 2012
Institute for Tribal Environmental Professionals Tribal Lands and Environment: A National Forum on Solid Waste, Emergency Response, Contaminated Sites and USTs August 20-23, 2012 Coos Bay, Oregon HAZWOPER
More informationBP U.S. Pipelines & Logistics (USPL) Safety Manual Page 1 of 8
Safety Manual Page 1 of 8 1. Purpose The purpose of this policy is to protect USPL employees and contractors from overexposure to benzene. 2. Scope This policy applies to all USPL employees and contractors
More informationSafety Data Sheet SUREPREP SKIN PROTECTANT WIPE
Safety Data Sheet SUREPREP SKIN PROTECTANT WIPE Section 1. Identification Product Identifier Synonyms Manufacturer Stock Numbers Recommended use Uses advised against Manufacturer Contact Address SUREPREP
More informationUT91 Version 2. Print Date 05/13/2010 REVISION DATE: 04/14/2010
SECTION 1 - PRODUCT IDENTIFICATION Trade name : Product code : 911 05 COMPANY : Euclid Chemical Company 19218 Redwood Road Cleveland, OH 44110 Telephone : 1-800-321-7628 Emergency Phone: : U.S. only: 1-800-424-9300
More informationSafety Data Sheet. AB Page 1 of 6 January 01, Relevant routes of exposure: Eye contact, skin contact, inhalation, ingestion
AB 30.00 Page 1 of 6 Section 1: PRODUCT AND COMPANY IDENTIFICATION Omega Products International P.O. Box 77220 Corona, CA 92877-0107 Company Phone Number: 1-951-737-7447 Emergency Phone Number: 1-951-737-7447
More informationSafety Data Sheet Lyden Oil Company
Page 1 of 8 1 PRODUCT AND COMPANY INFORMATION Product Name: Revision Date: 08/22/2016 Common Name: Metalworking Fluid CAS Number: Blend Product Code: 07168-AB Synonyms: Lubricant, Coolant, Metalworking
More informationSAFETY DATA SHEET Fresh Air Lemon Odor Counteractant. 1. Product and Company Identification. 2. Hazards Identification
Product Code: Product Name: Company Name: Web site address: SAFETY DATA SHEET 1. Product and Company Identification 61 SUNBELT LABORATORIES P.O. BOX 1563 STAFFORD, TX 77497 www.sunbelt-labs.com Phone Number:
More informationSafety Data Sheet INSTANT HOT PACK - SODIUM ACETATE
Safety Data Sheet INSTANT HOT PACK - SODIUM ACETATE Section 1. Identification Product Identifier Synonyms Manufacturer Stock Numbers Recommended use Uses advised against Manufacturer Contact Address INSTANT
More information