FLOW LIMITER 5% VENTURI 5 PSID TO ENGINE ANTI-ICE OVERBOARD PAC BLD SELECT HP LP NORM ISOLATION VALVE TO SERVICE AIR FROM APU (TYPICAL) 5 PSID

Transcription

1 Bleed Air System LEF FEED BUS LEF CB PANEL CKP EMP SEL 1 COLD HO CKP CAB COLD HO MANUAL SEL SEL MANUAL CKP PAC SUPPLY SUPPLY CAB PAC ON OFF HIGH OFF ON HIGH 3 ISOL VALVE 4 OFF 5 AUO ON EMER L ENG BLD AIR S H U 7 S H U CAB EMP SEL OFF 6 AUO ON EMER R ENG BLD AIR CROSSOVER RIGH FEED BUS LEF CB PANEL 2 6 BLEED AIR SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) ON OFF EMER R ENG BLD AIR O WING ANI-ICE FLOW LIMIER 5% VENURI OVERBOARD PAC HP VLV V OPEN LH 5 PSID RH P O ENGINE ANI-ICE PAC BLD SELEC HP LP NORM HP BLEED AIR SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) PRECOOLER HEA EXCHANGER 560 F O SERVICE AIR AND RUDDER BIAS ANI-ICE EMERGENCY PRESSURIZAION SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) HP PRECLR O'HEA LH RH 1 CKP EMP SEL AUO COLD MANUAL HO EMP CONROLLER HP BLEED AIR LP BLEED AIR PAC BLEED AIR (CONDIIONED) PAC BLEED AIR (UNCONDIIONED) RAM AIR Environmental Systems EMERG PRESS ON LH RH DUC O'HEA CKP CAB EMERG PRESS ON LH RH EMERGENCY PRESSURIZAION O WEMAC OULES O COCKPI O CABIN EMERGENCY PRESSURIZAION SHUOFF VALVE (NORMALLY CLOSED; POWERED OPEN) 1 UNIS 001 O 104 EXCEP HOSE MODIFIED O WEMAC OULES MIXED ASSEMBLY 7 S H U O WING ANI-ICE ISOL VALVE S H U 5 ON OFF EMER L ENG BLD AIR 1 HYDRAULIC POWERED FAN ISOLAION VALVE O SERVICE AIR FROM APU (YPICAL) LP BLEED M P O ENGINE ANI-ICE ISO VALVE OPEN 5 PSID PAC HP VLV V OPEN LH RH O WINDSHIELD ANI-ICE O SERVICE AIR AND RUDDER BIAS 560 F HIGH PRESSURE BLEED HP PRECLR O'HEA LH RH 2 EMP CONROLLER CAB EMP SEL COLD AUO MANUAL HO CKP PAC CAB PAC FROM PAS APU (YPICAL PAS) FROM RAM AIR SCOOP AIR GROUND FROM PAS APU (YPICAL PAS) 3 SQUA SWICH 4 CKP PAC ON OFF HIGH CAB PAC ON OFF HIGH Citation III/VI For training only 4C-1

2 4C-2 For training only Citation III/VI

3 Environmental Systems Air Distribution System CHECK VALVE FORWARD PRESSURE BULKHEAD RIGH WINDSHIELD DEFOG RIGH SIDE CONSOLE AIR OULE CROSSOVER DUC SIDE CONSOLE AIR RIGH ARMRES DUCING RIGH FLOOR LEVEL DUCING WEMAC BOOS BLOWER COCKPI CONDIIONED/ FRESH AIR RIGH EMERGENCY PRESSURIZAION AIR (HP BLEED) FOO- WARMER OULE DEFOG FAN FOO- WARMER OULE WEMAC OULES COCKPI LEF FLOOR LEVEL DUCING WEMAC OULES CABIN OVERHEAD COLD AIR DUCS CROSSFEED VALVE AUXILIARY HEAER FROM COCKPI PAC FLOOD COOL AIR OULE FROM CABIN PAC LEF EMERGENCY PRESSURIZAION AIR (HP BLEED) LEF WINDSHIELD DEFOG LEF SIDE CONSOLE AIR OULE MAIN ENRANCE DOOR LEF ARMRES DUCING EMERGENCY PRESSURIZAION MIXER CABIN CONDIIONED/ FRESH AIR HP BLEED AIR (UNCONDIIONED) PAC BLEED AIR (CONDIIONED) PAC BLEED AIR (UNCONDIIONED) Citation III/VI For training only 4C-3

4 4C-4 For training only Citation III/VI

5 Environmental Systems Pressurization System 1 FRON VIEW UP H L D 1 UP DOWN CABIN PRESSURE IN VACUUM REGULAOR CABIN PRESSURE IN OUFLOW VALVE CONROL LINE O OUSIDE AMOSPHERE DN MAX RAE NORM MIN MANUAL PRESSURIZAION CONROL VALVE GROUND FLIGH > 75% N 1 LANDING GEAR SQUA SWICH HROLE CAM SWICH (ABOVE 85% N 1 SPEED) ISOBARIC HOLD CONROL VALVE ALIUDE LIMI CONROL (13,500 F) CABIN PRESSURE IN SECONDARY OUFLOW VALVE (SLAVE, MODULAING) < 75% N 1 POSIIVE DIFFERENIAL PRESSURE CONROL 9.7 PSID O OUSIDE AMOSPHERE O OUSIDE AMOSPHERE AIRCRAF AL X 1000 F BARO IN HG R INCR FAUL DIGIAL CONROLLER AUO SCHED ALIUDE SELEC ELECRO- PNEUMAIC RANSFER VALVE O VACUUM REGULAOR A CABIN PRESSURE SELECOR B SENSE POR DUMP SWICH CABIN DUMP LEF FEED BUS LEF CB PANEL MAN NORM MANUAL-NORMAL SWICH FILER CABIN PRESSURE IN ALIUDE LIMI CONROL (13,500 F) POSIIVE DIFFERENAL PRESSURE CONROL 9.7 PSID CABIN PRESSURE IN PRIMARY OUFLOW VALVE (MODULAING) O OUSIDE AMOSPHERE VACUUM REGULAED VACUUM CABIN PRESSURE OUFLOW CONROL Citation III/VI For training only 4C-5

6 Air Cycle Machine FROM LEF ENGINE COCKPI AIR MIXED MUFF COCKPI PRESSURE REGULAING VALVE (NORMALLY OPEN-LOW) 1 FROM PAS APU O COCKPI 475 F SECONDARY HEA EXCHANGER O RIGH OVERHEAD PRIMARY HEA EXCHANGER URBINE COCKPI PAC 225 F COMPRESSOR PAC O'HEA CABIN PAC 225 F CKP CAB PAC HI WAER SEPARAOR O LEF OVERHEAD 475 F FROM RAM AIR SCOOP O CABIN CABIN AIR MIXED MUFF FROM RIGH ENGINE EMPERAURE CONROL VALVE ANI-ICE PNEUMAIC VALVE (35 F) 1 FROM PAS APU CABIN PRESSURE REGULAING VALVE (NORMALLY OPEN-LOW) ACM COMPRESSED AIR ENGINE BLEED AIR PRIMARY HEA EXCHANGER OUPU AIR SECONDARY HEA EXCHANGER OUPU AIR ACM OUPU AIR ACM CONDIIONED AIR RAM AIR SUCION 1 FROM PAS APU: IF INSALLED 4C-6 For training only Citation III/VI

7 Environmental Systems LP Bleed Air Supply APU FLOW CONROL SHUOFF VALVE O ISOLAION VALVE AND ECU BLEED AIR SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) HP BLEED AIR SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) O SERVICE AIR CHECK VALVE FROM HP BLEED AIR FROM APU P 5 PSID OFF ON EMER CHECK VALVE O ENGINE ANI-ICE FLOW LIMIER 5% VENURI L ENG BLEED AIR L ENG LP AIR BLEED Citation III/VI For training only 4C-7

8 HP Bleed Air Supply R ENG LP BLEED AIR O ENGINE ANI-ICE R ENG HP BLEED AIR FLOW LIMIER 5% VENURI PRECOOLER HEA EXCHANGER OFF HP BLEED AIR SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) ON R ENG BLD AIR O WING ANI-ICE EMER 5 PSID P PAC BLD SELEC HP LP NORM HP PRECOOLER O'HEA SENSOR O SERVICE AIR AND RUDDER BIAS ANI-ICE EMER PRESS SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) EMER PRESS SHUOFF VALVE (NORMALLY CLOSED; POWERED OPEN) BLEED AIR SHUOFF VALVE (NORMALLY OPEN; POWERED CLOSED) 4C-8 For training only Citation III/VI

9 Environmental Systems Bleed Air Supplies Low pressure (LP) and/or high pressure (HP) bleed air obtained from the engines supplies the: air conditioning system normal and emergency pressurization systems wing, windshield, and engine anti-icing systems rudder bias system service air system (door seal and pressurization system air ejector). If installed, the auxiliary power unit (APU) also supplies bleed air for the air conditioning and service air systems. LP Air LP bleed air from each engine s axial compressor flows through a flow-limiting venturi before it enters the collector manifolds. he venturis limit total LP bleed air extraction to 5% of that produced by the engine. In the collector manifolds, bleed air flows through a check valve and shutoff/pressure regulating valve before it reaches the environmental control unit packages (PACs). he check valves prevent reverse airflow from an operating engine to an inoperative engine. When operating with the APU bleed air switch in OPEN, the APU supplies bleed air through a check valve and open bleed air shutoff valve into the collector duct that supplies the PACs. At low engine power settings on the ground, supplying the environmental control system with APU bleed air is more efficient. Citation III/VI For training only 4C-9

10 HP Air HP bleed air from each engine s HP compressor flows through a precooler and slave valve before it passes through the engine pylon into the tee duct. he slave valve, controlled by a pilot valve, regulates the air bypassing the precooler to maintain it at a temperature between 500 and 550 F (260 and 288 C). If the bleed air temperature downstream of the precooler exceeds 560 ±12 F (293 ±7 C), an overtemperature switch illuminates the associated HP PRECLR O HEA annunciator. In the tee duct, the HP air supply splits to supply the: emergency pressurization system through the anti-ice/emergency pressurization shutoff valve and emergency pressurization shutoff valve wing and windshield anti-ice systems through the antiice/emergency pressurization shutoff valve, wing anti-ice shutoff valve, and windshield pressure regulating shutoff valve collector ducts through the open HP bleed air shutoff valve service air and rudder bias systems engine nacelle anti-icing system. Air Conditioning On the ground with the throttle levers below the 55% N 1 position and the PAC BLD SELEC switch in NORM, the HP bleed air shutoff valves open to supplement LP bleed air. Advancing the throttles above the 55% N 1 position, closes the HP bleed air shutoff valves; LP bleed air is then the sole source for the PACs. Opening and closing of the HP bleed air shutoff valve can also be controlled by placing the PAC BLD SELEC switch in LP (shutoff valve closed) or HP (shutoff valve open). 4C-10 For training only Citation III/VI

11 Environmental Systems Normally, left and right bleed air separately supply the cabin and cockpit PACs. Placing the ISOL VALVE switch in OPEN supplies 28V DC to open the isolation valve and connect the two bleed air supplies. his allows one engine to supply both systems during an engine failure. Check valves prevent reverse bleed air flow to the inoperative engine. On unit 200 and subsequent, an optional Freon air conditioning system supplements the PACs for ground and low altitude operations. ECU PACs On units 001 to 104, the ECU PACs consist of a dual core primary and secondary heat exchanger, air cycle machine (ACM), pressure regulator and shutoff valve, temperature sensor and thermal switches, anti-ice pneumatic valve assembly, water separator, and flow-limiting venturi. On unit 105 and subsequent, the ECU PACs consist of a heat exchanger, air cycle machine, fan housing, water separator, bypass valve, and overtemperature switch. A PACs bleed air flows through a pressure regulator and shutoff valve before it enters the primary heat exchanger. he shutoff valve, controlled by a high/low solenoid, regulates bleed air pressure to 28.5 PSIG in the high setting and to 15 PSIG in the low setting. After the flow-limiting venturi, bleed air then moves through a ram air cooled primary heat exchanger that provides initial air cooling before it reaches the ACM s compressor. As air flows through the compressor, it is compressed and heated before it passes through the secondary heat exchanger for cooling. After passing through the secondary heat exchanger, air flows to the ACM s turbine where it rapidly expands and cools as it expends energy to drive the turbine. he rapidly spinning turbine, in turn, drives the ACM s compressor. Citation III/VI For training only 4C-11

12 If installed, a hydraulically operated fan draws air through the PAC heat exchangers to supplement ground cooling. he fan deactivates on takeoff. On units 001 to 104, there is a thermal switch at the compressor outlet and turbine inlet. If temperature of the air exiting the compressor exceeds 475 F (246 C) or the air temperature entering the turbine exceeds 225 F (107 C), the thermal switches illuminate the associated PAC O HEA CKP/CAB annunciator and perform an automatic PAC shutdown. On unit 105 and subsequent, if the temperature of the air exiting the ACM compressor exceeds 435 ±15 F (224 ±8 C), the compressor outlet thermal switch illuminates the associated PAC O HEA CKP/CAB annunciator and performs an automatic PAC shutdown. After exiting the ACM, conditioned air combines with air bypassed around the primary heat exchanger. In the water separator, a coalescer removes water from the moisture-laden conditioned air. An ejector collects water and supplies it to the secondary heat exchanger to assist cooling. A temperature switch downstream of the water separator monitors water separator outlet air temperature. At temperatures below 35 F (1.6 C), the switch opens an anti-ice pneumatic valve that heats the air entering the water separator to prevent icing. Distribution and Control Conditioned air mixed with hot bleed air heats and pressurizes the cockpit and cabin. Cold conditioned air directly from the PACs cools and ventilates the cockpit and cabin through overhead Wemac ducts. On the ground, forced air from a ram air scoop at the vertical stabilizer base ventilates the cockpit and cabin. 4C-12 For training only Citation III/VI

13 Environmental Systems emperature Control With the CKP EMP SEL and CAB EMP SEL knobs in the AUO range, cockpit and cabin temperature controllers regulate air temperature based on temperature signals provided by zone and duct temperature sensors. In response to these inputs and the desired air temperature selected through the control panel, each controller opens or closes its temperature control valve to increase or decrease the amount of hot bleed air supplied to the mixer muffs. Placing a CKP or CAB EMP SEL knob in the MANUAL range allows the crew to manually control cockpit and cabin air temperature by directly controlling the opening and closing of the temperature control valves. hrough the source selectable digital temperature indicator, the crew monitors zone and supply temperature and the setting selected for temperature control. If the cockpit and cabin supply duct temperature exceeds 300 F (149 C), a duct overheat switch illuminates the associated DUC O HEA CKP/CAB annunciator. If a duct overheats, selecting a lower temperature with the environmental control closes the temperature control valve to cool the air supply. If a cockpit PAC malfunctions or its CKP PAC knob is in OFF, a crossflow check valve between the cabin and cockpit ducting opens to admit cabin PAC conditioned air into the cockpit. Boost and Flood Cooling On unit 105 and subsequent; prior aircraft with SB , with the WEMAC BOOS switch in ON, an electric fan in the aft vanity mixes cabin air with conditioned air to increase air flow through the overhead distribution ducts and prevent fogging from the Wemac outlets. Citation III/VI For training only 4C-13

14 On unit 105 and subsequent, an optional flood cooling system allows rapid cooling by directing most of the cold conditioned air from the PACs through an aft bulkhead mounted plenum into the cabin. With the control switch in FLOOD COOL, a motor-driven door partially closes off the overhead distribution ducts to route most of the air through the flood cooling outlet. With the control switch in OFF, the door closes the outlet and cold air flows normally through the overhead distribution ducts. Freon Air Conditioning With the aircraft electrical system powered by the engine-driven generators or external power, placing the A/C switch in ON energizes the air conditioner compressor and evaporator fans. he air conditioner compressor then cycles on and off in response to the setting made with the A/C EMP selector. he system provides cold conditioned air through the forward evaporator and fan in the forward end of the dropped aisle and the rear evaporator and fan in the right vanity area. With the A/C switch in FAN, the compressor does not operate but the fans continue to circulate air through the cabin. Depending on the position of the FWD EVAP and AF EVAP switches, the evaporator fans operate at high (HI), medium (MED), or slow (LOW) speeds. Auxiliary Heating An auxiliary electric heater in the cockpit air distribution ducts supplements normal heating and assists in window defogging. hrough the CKP AUX FAN and CKP AUX FAN/HEA switches, the flight crew can select: fan low/heat low fan high/heat high fan high/heat low. 4C-14 For training only Citation III/VI

15 Environmental Systems o prevent overheating, the system will not operate with the FAN switch in LOW and the FAN/HEA switch in HIGH. After placing both switches in OFF, a cooldown circuit runs the fan until output temperature is below 130 F (54 C). Baggage Compartment Heating With DC power available and the BA HR switch in ON, an electric blower, heating elements, and ambient temperature switch maintain baggage compartment temperature between 70 and 90 F (21 and 32 C). If the baggage compartment temperature reaches 180 F (82 C), an overheat temperature switch illuminates the BAG HR O HEA annunciator. If the temperature continues to rise, thermal fuse(s) melt at 280 F (138 C) to cut power to the heating elements. Instrument Panel Cooling With the W/S DEFOG switch in LOW or HIGH, a 28V DC fan underneath the defog deck circulates air behind the instrument panel for cooling. he fan also operates if a thermal switch senses a temperature above 98 F (37 C) behind the instrument panel. On aircraft with EFIS, the fan operates continuously. Avionics Cooling With the battery switch in BA, cooling fans circulate air through the avionics equipment to prevent overheating. On units 001 to 178, a thermal switch with a 98 F (37 C) set-point controls power to the fans. On unit 179 and subsequent, the fans operate whenever the battery switch is in BA. Citation III/VI For training only 4C-15

16 Pressurization With a constant supply of conditioned air flowing into the cabin, the pressurization system automatically maintains a selected cabin altitude, climb rate, and descent rate with two outlow valves that control the rate of cabin air escape to atmosphere. At the aircraft s maximum operating altitude of 51,000 ft, the system s 9.3 PSID maximum cabin pressure differential maintains a comfortable 8,000 ft cabin altitude. he system s primary and secondary outflow valves respond to electrical commands from the pressurization controller during automatic operation and pneumatic commands from the manual pressurization control valve during manual operation. If a system failure occurs, the outflow valves prevent cabin altitude from exceeding 13,500 ±1,500 ft and pressure differential from exceeding 9.7 PSID. If the pressurization system completely fails, the cabin or cockpit PACs provide sufficient airflow to maintain cabin pressure. At power-up, the pressurization system automatically performs a self test of the controller, outflow valves, squat switches, and system components. If a component fails the self-test, pressurization can be controlled through the manual pressurization control valve. Automatic Operation here are two automatic operating modes: auto-schedule and cabin altitude select. In either mode, the digital cabin pressurization controller electrically controls the primary and secondary outflow valves through their electro-pneumatic transfer valves. Auto-Schedule With pressurization system switches in NORM and AUO SCHED, the crew sets cabin climb rate and landing field elevation and makes barometric pressure corrections. 4C-16 For training only Citation III/VI

17 Environmental Systems On the ground with the throttles above the 75% N 1 position, the pressurization controller pre-pressurizes the cabin to eliminate cabin altitude bumps at liftoff. As the aircraft leaves the ground, the squat switches signal the controller to enter its flight mode. he controller, using the landing field barometric pressure entered, uses its auto schedule to provide a cabin altitude based on aircraft altitude. During climb to altitude and descent, the crew manually selects the cabin rate-of-climb while the controller provides climb and descent rate limiting. If the crew selects an excessive climb or descent rate as compared to the auto schedule, the controller limits the rate to match the schedule. he controller, however, does not limit climb and descent rates less that the auto schedule requires. he crew sets the required barometric pressure during the approach. At aircraft touchdown, the squat switches signal the controller to enter its landing mode thus preventing a lower cabin altitude than field elevation. After one minute, the system enters ground mode: it opens both outflow valves to dump cabin pressurization. Cabin Altitude Select With the pressurization control switches in NORM and ALI- UDE SELEC, the crew sets desired cabin rate-of-change, cabin altitude, and barometric pressure correction. he controller then automatically controls primary and secondary outflow valve opening and closing to achieve the desired settings. In altitude select mode, the crew can select cabin rate-of-change from 150 to 2,500 FPM up or 90 to 2,500 FPM down. Citation III/VI For training only 4C-17

18 Manual Operation If the system loses power, it automatically enters manual mode. Placing the MAN/NORM switch in MAN also places the system in manual mode. he crew then selects cabin altitude and rateof-change on the cabin altitude and differential pressure indicator and the rate-of-climb indicator. With the system in manual mode, the crew directly controls cabin altitude through the UP/HLD/DN switch and cabin rate-of-change through the RAE knob. Holding the switch in UP raises cabin altitude by connecting the control valve to atmosphere. he outflow valve opens and cabin altitude climbs. Holding the switch in DOWN connects the control valve to cabin pressure. he outflow valve closes and cabin altitude descends. Emergency Pressurization If cabin altitude climbs above 8,500 ±350 ft, the cabin altitude switch closes to illuminate the CABIN AL 8500 F annunciator. If cabin altitude continues to climb and reaches 10,000 ±350 ft, two barometric switches close to sound an aural warning. Pressing the CAB AL WARN button silences the warning. If cabin altitude continues to climb and reaches 13,500 ±500 ft, a second set of two barometric switches close to automatically initiate emergency pressurization. he emergency pressurization shutoff valves energize to bypass the PACs and supply bleed air directly into the cabin and cockpit. Placing the L/R ENG BLD AIR switches in EMER also initiates emergency pressurization. he primary and secondary outflow valves also close to limit cabin altitude to 13,500 ±500 ft. 4C-18 For training only Citation III/VI

19 Environmental Systems Finally, a sixth barometric pressure switch connected to the autopilot system closes at 13,500 ±500 ft to provide a signal to the autopilot computer. With this switch closed, a ground provided by the air data computer (aircraft at approximately 35,000 ft), and the autopilot engaged, the autopilot system enters the emergency descent mode. Citation III/VI For training only 4C-19

20 Bleed Air Manifold Power Source Distribution Control Monitor Protection Engines (L/R HP and LP air) APU air Normal air conditioning/pressurization Left engine to cockpit PAC Right engine to cabin PAC When open, isolation valve connects 2 sides Emergency pressurization Engine anti-ice system Wing anti-ice system Windshield anti-ice system Rudder bias Entry door seal Cabin pressure control air ejector Switches CKP/CAB AIR ENG BLD AIR L/R (EMER) ISOL VALVE APU BLEED AIR OPEN Anti-ice systems Annunciators HP PRECLR O HEA PAC O HEA CKP/CAB EMERG PRESS ON ISO VALVE OPEN Anti-ice systems ENG BLD AIR CBs (5A) Bleed air shutoff valve 4C-20 For training only Citation III/VI

21 Environmental Systems Pressurization Systems Power Source Distribution Control Monitor Protection Bleed air manifold APU air Left Feed bus Aircraft pressure vessel MAN/NORM controller switch AUO SCHED/ALIUDE SELEC switch Cabin DUMP/PRESSURIZE switch Digital controller hrottle switches CAB AL WARN MUE/ES button Cabin altitude/differential pressure indicator Cabin rate-of-climb indicator CABIN AL 8500 F annunciator Cabin altitude warning horn 10,000 ft Amber FAUL light PRESSURIZAION CB (5A) Outflow valves Altitude limit control 13,500 ft Positive differential pressure control 9.7 PSID Cabin pressurization failure warning system Emergency pressurization system ENG BLD AIR selector on EMER Squat switches Citation III/VI For training only 4C-21

22 Air Conditioning System Power Source Distribution Control Monitor Protection Left Feed bus Crossover Right Feed bus Bleed air manifold Fresh air (units 001 to 104) Freon system (optional on unit 200 and subsequent) Cockpit Cabin Switches PAC BLD SELEC (HP/LP/NORM) CKP/CAB PAC ENG BLD AIR CKP/CAB EMP SEL emperature display selector Optional Freon system A/C switch FWD/AF EVAP switches A/C EMP controls Annunciators DUC O HEA CKP/CAB PAC O HEA CKP/CAB PAC HI PAC HP VLV OPEN EMERG PRESS ON Circuit breakers FWD/AF EVAP FAN with optional Freon system (10A) COCKPI EMP (5A) CABIN EMP (5A) MAN CABIN EMP (5A) DEFOG FAN (5A) Overtemperature shutdown for PACs 4C-22 For training only Citation III/VI