General Information valve design valve selector guide catalog numbering system warranty terms

Transcription

1 CERTIFIED High Equipment Table of Contents 2 eneral Information valve design valve selector guide catalog numbering system warranty terms Low Valves, Fittings and Tubing - 0,000 and 5,000 psi service Taper Seal - valves fittings line filters check valves safety heads rupture discs tubing connection details NPT - valves fittings couplings bulkheads caps line filters check valves safety heads rupture discs Medium Valves, Fittings and Tubing - 20,000 psi service valves fittings unions bulkheads caps line filters check valves safety heads rupture discs anti-vibration gland assemblies tubing coned and threaded nipples connection details High Valves, Fittings and Tubing - 0,000, 40,000 and 60,000 psi service valves fittings unions bulkheads caps line filters check valves safety heads rupture discs anti-vibration gland assemblies tubing coned and threaded nipples connection details Ultra High Valves, Fittings and Tubing - 00,000 and 50,000 psi service valves fittings check valves tubing coned and threaded nipples connection details Specialty Valves ball valves hastelloy valves high temperature valves metering valves relief valves male bottom connection valves block and bleed valves subsea ball valves 8 ir Operated Valves Mini-Hippo piston operators Hipco diaphragm operators Remarco diaphragm operators Hippo piston operators Remetco piston operated fine metering valves ccessories female to male adapters male to male adapters NPT and hose fittings female to female couplings thermocouple adapters pressure gauges Tooling reseating tools coning tools threading tools coning and threading instructions 0 Vessels and Reactors O-ring seal reactors- series OC confined gasket closure reactors-series C bolted closure reactors clover leaf reactors O-ring closure reactors-series R tubular reactors-series TOC micro reactors-series MS Pumping Systems, Intensifiers, as oosters and High enerators pumping systems intensifiers gas boosters high pressure generators 2 Technical Information conversion tables packing options min. safety hold down nut torque min. bend radius for high pressure tubing flow coefficients pressure ratings of bolted closure reactors recommended torque max. recommended volumetric flow rate pressure rating reduction graphs Oil and as Products valves fittings line filters check valves tubing High Equipment Company R 5/

2 High Equipment eneral Information High Equipment Company has developed an extensive line of components and systems designed to satisfy the unique requirements of elevated pressure applications. Since our founding in 54, we have been singularly focused upon this market segment and have consistently committed the resources necessary to be the industry s most reliable and economical source for quality high pressure products. This dedication to excellence within our core business has earned HiP preferred supplier status within diverse markets such as waterjet cutting and cleaning, oil and gas, chemical and petrochemical, research and development, universities, government, and general industry. Our product line includes a complete offering of valves, fittings, tubing, gauges, safety devices, pressure vessels, reactors, pumping systems, intensifiers, gas boosters and pressure generators for use at pressures through 50,000 psi. Stainless steel is the material most commonly used for our standard products, although we offer a variety of other materials to address alternative operating conditions. We maintain a significant inventory of many standard components, allowing us to provide fast response and delivery to our customers. For special requirements, our flexible structure and skilled machinists will produce a component or system designed to your individual specifications, in a timely manner. Index Page Valve Design Valve Selector uide Catalog Numbering System Warranty & Terms R 6/.

3 High Equipment Valve Design eneral Valve bodies through 00,000 psi are high tensile Type 6 stainless steel, 50,000 psi valve bodies are -4 PH stainless steel. Stem assemblies have non-rotating tips to prevent galling with valve seats. Packing is located below the stem threads to prevent contact with media (liquid or gas). Packing glands are equipped with locking devices or lock nuts. Six valve patterns (see chart on page.). Tubing connections are: /6",,,, /6",, and ". Pipe connections include:,,,,, and " NPT. Remote control air operators are available for most valves. Positive uide Stem: High Equipment Company's patented Positive uide stem assembly virtually eliminates lower stem rotation one of the most common causes of premature stem failure. The lower section stem is manufactured from hardened -4 PH stainless steel for exceptional wear and corrosion resistance and can be easily serviced with no special tooling required. The one-piece upper section stem eliminates the need for continual adjustment and minimizes loose handle backlash. The Positive uide Stem is standard for all F4, F6, HF4, HF6, and HF valves, and 60,000 psi HF2 valves. Positive uide Stem Rolled Style Stem: This simple two-piece design is also nonrotating and is ideal for smaller valves and for valves made from exotic materials. The standard lower section stem is manufactured from hardened -4 PH stainless steel. It is affixed to a one-piece upper stem requiring no periodic adjustment. The two stem components are free to rotate independently of each other, thereby minimizing rotation of the lower stem against the valve seat. The Rolled Style Stem is standard for all F, F2, NF, NF, LF4, LF6 valves, 0,000 psi HF2, XF4, and XF6 valves, as well as most valves requiring stems made from exotic materials. It is optional for any valve normally supplied with a Positive uide Stem. Pinned Stem Design: This variation on the Rolled Style Stem is a three-piece design in which the lower stem is pinned into a freely-rotating stem guide. It has all of the advantages of the rolled style stem, with the additional benefit of a replaceable lower section stem. The Pinned Stem Design is standard for all NFC, NFD, NFF, NFH, LF, LF2, LF6, and HF6 valves. Pinned Stem Rolled Style Stem.2

4 Quick Selector uide to Standard Valves Taper Seal Valves 0,000 psi Tubing Size O.D. I.D. Two Way Straight 0-F4 0-F6 Two Way ngle 0-2F4 0-2F6 Three Way Two Press 0-F4 0-F6 Three Way One Press 0-4F4 0-4F6 Three Way Two Stem 0-5F4 0-5F6 Replaceable Seat N N Medium Valves 5,000 psi /6".00" /6" /64" /64" 5-F 5-F2 20-LF4 20-LF6 5-2F 5-2F2 20-2LF4 20-2LF6 5-F 5-F2 20-LF4 20-LF6 5-4F 5-4F2 20-4LF4 20-4LF6 5-5F 5-5F2 20-5LF4 20-5LF6 N N 20-2LF4R 20-2LF6R 20,000 psi /6" 5 /6" 20-LF 20-2LF 20-LF 20-4LF 20-5LF 20-2LFR /64" 20-LF2 20-2LF2 20-LF2 20-4LF2 20-5LF2 20-2LF2R High Valves " /6".040".08" 20-LF6 0-HF2 0-HF4 20-2LF6 0-2HF2 0-2HF4 20-LF6 0-HF2 0-HF4 20-4LF6 0-4HF2 0-4HF4 20-5LF6 0-5HF2 0-5HF4 20-2LF6R 0-2HF2R 0-2HF4R 0,000 psi 0-HF6 0-2HF6 0-HF6 0-4HF6 0-5HF6 0-2HF6R /6" /6" 0-HF 0-2HF 0-HF 0-4HF 0-5HF 0-2HFR ".4" 0-HF6 0-2HF6 0-HF6 0-4HF6 0-5HF6 0-2HF6R.020" 60-HF2 60-2HF2 60-HF2 60-4HF2 60-5HF2 60-2HF2R 60,000 psi /6" 60-HF4 60-HF6 60-2HF4 60-2HF6 60-HF4 60-HF6 60-4HF4 60-4HF6 60-5HF4 60-5HF6 60-2HF4R 60-2HF6R Ultra High Valves 00,000 psi 50,000 psi /6" /6" /6" /6" 60-HF 00-XF4 50-XF6 60-2HF 00-2XF4 50-2XF6 60-HF 00-XF4 50-XF6 60-4HF 00-4XF4 50-4XF6 60-5HF N N 60-2HFR 00-2XF4R 50-2XF6R High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

5 High Equipment Catalog Numbering System PRESSURE TYPE CONNECTION CONNECTION OPTIONS / CCESSORIES (IF DIFFERENT FROM FIRST 0 - HF CONNECTION) Type of Connection(s) Options Series Components Size and Type 0 =0,000 psi 5 = 5,000 psi 20 = 20,000 psi 0 = 0,000 psi 40 = 40,000 psi 60 = 60,000 psi 00 = 00,000 psi 50 = 50,000 psi Catalog part numbers for some components (NPT fittings, special alloy parts) have been maintained for historical consideration. The referred pressure series may not reflect the actual pressure rating. Please refer to applicable catalog page for pressure rating, or consult the factory. 2 = land, Collar or Sleeve = nti-vibration ssembly = Plug = 2-Way Straight Valve 2 = 2-Way ngle Valve = -Way Valve with Two Connections 4 = -Way Valve with One Connections 5 = -Way, 2-Stem Valve 6 = all Valve (Floating) 2 = Coupling or dapter 22 = Elbow 2 = Tee 24 = Cross 4 = Check Valve 5 = Line Filter 6 = Safety Head (Straight) 6 = Safety Head (Tee Type) = 2-Way all Valve * 2 = -Way all Valve 80 * = -Way all Valve Diverter * 4 = 2-Way all Valve * 5 = -Way all Valve 80 * 6 = -Way all Valve Diverter * = -Way Mini all Valve /4 NPT 80 = 2-Way all Valve * 8 = -Way all Valve 80 * 82 = -Way all Valve Diverter * * (Trunion) How to Order Valves and Fittings Female Simply indicate catalog number and specify option or special requirement. Examples: 0-HF4 = 0,000 psi Straight Valve for / 4 " O.D. tubing 60-2HF4 = 60,000 psi Tee for / 4 " O.D. tubing 5-2F2 = 5,000 psi Straight Coupling for / 8 " O.D. tubing, Taper Seal connections 5-2F2NM = 5,000 psi dapter with one end / 8 " O.D. Female Taper Seal and opposite end Male / 4 " NPT Pipe 0-HF6-HT = 0,000 psi Straight Valve for / 8 " O.D. tubing with High Temperature Extension HIPCO 0-2NF (N/C) = 0,000 psi ngle Valve for / 4 " NPT Pipe with Hipco ir Operator, Normally Closed HIPPO 5-4F (N/C) = 0,000 psi ngle Valve for / 4 " Taper Seal with Hippo Piston Operator, Normally Closed 60-2HF4 (Hastelloy C-26) = 60,000 psi Straight Coupling for / 4 " O.D. tubing, made from Hastelloy C-26 material Male F M /6" Taper Seal F2 M2 Taper Seal F4 M4 Taper Seal F6 M6 Taper Seal LF4 LM4 Medium LF6 LM6 Medium LF LM /6" Medium LF2 LM2 Medium LF6 LM6 " Medium HF2 HM2 High HF4 HM4 High HF6 HM6 High HF HM /6" High HF6 HM6 " High XF4 XF6 NF NF NFC NFD NFF XM4 XM6 NM NM NMC NMD NMF Ultra High Ultra High NPT Pipe NPT Pipe NPT Pipe NPT Pipe NPT Pipe NFH NMH " NPT Pipe H H2 /6" Hose Hose H6 " Hose H2 5 /6" Hose -V = Micro Control Metering ssembly (See page 6.5) -HT = High Temperature Stem Extension (Up to,000 F) (See page 6.4) -SS = Sour as (H 2 S) Service -N/O = Normally Open -N/C = Normally Closed -K = With ntivibration Collars and lands -RE = Regulating Tip -TSR8 = all Valve ctuator -TD8 = all Valve ctuator Double cting -W/O = Without Collars and lands -LT = Low Temperature Stem Extension (to -20 F) -MPO-NO = Medium Duty Piston Operator Normally Open -MPO-NC = Medium Duty Piston Operator Normally Closed -HPO-NO = Heavy Duty Piston Operator Normally Open -HPO-NC = Heavy Duty Piston Operator Normally Closed -EHPO-NO = Extra Heavy Piston Operator Normally Open -EHPO-NC = Extra Heavy Piston Operator Normally Closed.4 R5 8/04

6 Warranty High Equipment Company warrants the products which it manufactures to be free from defects in material and workmanship which would impair their intended usefulness. This warranty is for a period of one year after the date of shipment. Warranty is limited to the repair or replacement of any item manufactured by High Equipment Company. High Equipment Company shall not be liable for any direct or indirect consequential damage arising from a failure or malfunction of the equipment. This warranty further excludes damage, failure or malfunction which is caused by corrosion or erosion common to the material supplied. Terms: Net 0 for qualified accounts FO: Erie, P - US High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

7 High Equipment Low Valves, Fittings and Tubing Taper Seal and NPT 0,000 and 5,000 psi service High Equipment Company has developed the Taper Seal and NPT lines of products to assure safe and easy plumbing through 5,000 psi. These needle valves, fittings, line filters, check valves, safety heads, rupture discs and tubing are engineered and manufactured to the highest standards of repeatable quality. The reliable performance of these products has made HiP one of the world's leading suppliers of elevated pressure components. Index - Taper Seal Page Valves Fittings Line Filters & Check Valves Safety Heads Rupture Discs Tubing Connection Details ppendix Index - NPT Page Valves Fittings Couplings, ulkheads & Caps Line Filters & Check Valves Safety Heads & Rupture Discs R /06 2.

8 High Equipment Taper Seal Needle Valves 0,000 and 5,000 psi service Compression type tubing connections for /6",,, and O.D. tubing. Requires no special tooling for tubing preparation (simply cut off, deburr, and insert tubing into connection). Connection details are shown on page 2.. Non-rotating tip stems are standard for on-off service and insure long life on valve seats. Regulating tip stems are available at no additional cost, add - RE to the catalog number. lands and sleeves are supplied with each valve unless otherwise requested (glands and sleeves shown on 2.). Materials include high tensile type 6 stainless steel for the valve body and hardened -4PH stainless steel lower section stem. Packing is Teflon (450 F) standard, with optional Viton (50 F), UN-N (200 F) or rafoil (650 F) available at no additional cost. ir operators for remote control operation are available for all valves. (Select required valve and add HIPCO. Refer to section.0 for additional data). F ( /6") and F2 ( ) 5,000 psi Valve Features Non-rotating stem tips Packing below stem threads Type 6 ss high tensile bodies Positive gland lock device No stem adjustment needed lack T-handles or choice of 4 colors Tube sizes /6" through F4 ( ) and F6 ( ) 0,000 psi 2.2

9 Taper Seal Valves K Two Way Straight Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness D L F E J H /6" O.D. O.D. O.D. O.D. 5-F 5-F2 0-F4 0-F6 5,000 5,000 0,000 0,000 F F2 F4 F /6" /6" 5 /6" /6" 5 /6" 5 /6" /64" /64" " " D L E K J H Two Way ngle Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. O.D. 5-2F 5-2F2 0-2F4 0-2F6 5,000 5,000 0,000 0,000 F F2 F4 F /6" /6" 5 /6" 2 5 /6" /6" /6" /6" 2 /6" 2 /6" 5 /6" 5 /6" /64" /64" " " /6" O.D. K Three Way Valves / Two Connections D L J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 5-F 5,000 F /6" /64" O.D. 5-F2 5,000 F2 /6" /6" 5 /6" /6" 5 /6" /64" F E O.D. O.D. 0-F4 0-F6 0,000 0,000 F4 F6 5 /6" 5 /6" /6" /6" 2 /6" 2 /6" " " K Three Way Valves / One Connection D L J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 5-4F 5,000 F /6" /64" F O.D. 5-4F2 5,000 F2 /6" 5 /6" 5 /6" /6" 5 /6" /64" E O.D. O.D. 0-4F4 0-4F6 0,000 0,000 F4 F6 5 /6" 5 /6" /6" /6" /6" /6" 2 /6" 2 /6" " " J F L D K F J E H Three Way / Two Stem Connection Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. O.D. O.D. O.D. 5-5F 5-5F2 0-5F4 0-5F6 5,000 5,000 0,000 0,000 F F2 F4 F /6" 4 5" 8 8 " /6" /6" 2 2 /6" /6" 5 /6" 5 /6" 2 2 /64" /64" " " High Equipment Company R 8/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.

10 High Equipment lands/sleeves/plugs Elbows/Tees/Crosses complete range of elbows, tees, and crosses is available for all of the tubing connection sizes. Material is high tensile 6 stainless steel. Standard tubing glands and sleeves are furnished unless otherwise specified. Connection Components Tube Catalog No. Size land Tube Catalog No. Size Sleeve Tube Catalog No. Size Plug 5-2M /6" 5-2M2 0-2M4 0-2M6 5-2 /6" M /6" 5-M2 0-M4 0-M6 E H F Taper Seal Elbows Catalog No. psi Connections - E F H Thickness 5-22F 5,000 /6" O.D. TUE F /6" /6" 5-22F2 5,000 O.D. TUE F2 0-22F4 0,000 O.D. TUE F4 " " " 0-22F6 0,000 O.D. TUE F6 " " " C E H F Taper Seal Tees Catalog No. psi Connections --C E F H Thickness 5-2F 5,000 /6" O.D. TUE F " /6" 5-2F2 5,000 O.D. TUE F2 0-2F4 0,000 O.D. TUE F4 " " " 0-2F6 0,000 O.D. TUE F6 " " " C E D H F Taper Seal Crosses Catalog No. psi Connections --C-D E F H Thickness 5-24F 5,000 /6" O.D. TUE F " " 5-24F2 5,000 O.D. TUE F2 0-24F4 0,000 O.D. TUE F4 " " " 0-24F6 0,000 O.D. TUE F6 " " " 2.4

11 Line Filters The line filters as shown utilize sintered stainless steel filter discs (F2 & F pc./set, F4 & F6 4 pc./set). Porosities are available as per the chart to the right. If not otherwise specified, 00 micron filter discs are supplied. (One micron = 0.00 millimeters). Material of bodies and end covers is high tensile 6 stainless steel. Standard tubing glands and sleeves are provided unless otherwise specified. FLOW Micron Size Filter Hex vailable Catalog No. psi Connections Length Size F 5,000 /6" TPER SEL 5-5F2 5,000 TPER SEL 0-5F4 0,000 TPER SEL 5 0-5F6 0,000 TPER SEL 5 all Check Valves all type check valves insure flow in one direction only. Material for bodies, balls, and covers is high tensile 6 stainless steel. Standard tubing glands and sleeves are provided unless otherwise specified. FLOW Soft Seat Check Valves Soft seat check valves insure flow in one direction only and can be mounted in any position. These are highly reliable for both gas and liquid service. Standard O-ring (soft seat) material for the sealing surface is una-n (nitrile) with other materials including Teflon and Viton available on request. Temperature is limited by the choice of O-ring material. Material of all other parts is high tensile 6 stainless steel. Standard glands and sleeves are provided unless otherwise specified. Catalog No. psi Connections Length Hex 5-4F 5,000 /6" TPER SEL " 5-4F2 5,000 TPER SEL /6" " 0-4F4 0,000 TPER SEL " 0-4F6 0,000 TPER SEL " FLOW Catalog No. psi Connections Length Hex 5-4F-T 5,000 /6" TPER SEL " 5-4F2-T 5,000 TPER SEL " 0-4F4-T 0,000 TPER SEL " 0-4F6-T 0,000 TPER SEL " High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.5

12 High Equipment Safety Heads choice of three safety head designs is available: male inlet, female inlet (straight), and tee type. The male inlet design can be inserted directly into the tubing connections of valves and various fittings such as tees and crosses, or located in pressure vessels. Outlet connections on all sizes are pipe (NPT). This outlet may be connected to a suitable discharge line to vent pressure to a safe location in the event of bursting of the rupture disc. Torque required for sealing rupture discs will range from 40 to 60 foot pounds, depending upon pressure and media being used. Material of bodies and hold down nuts is high tensile 6 stainless steel. Hold down rings are hardened -4PH stainless steel. Standard tubing glands and collars (sleeves) are provided unless otherwise specified. Note: Rupture discs are not included and must be ordered as a separate item. NPT Male Inlet Safety Heads Inlet Hex Catalog No. psi Connection Length Size 0-6M4 0,000 TPER SEL 2 " 0-6M6 0,000 TPER SEL 2 " NPT Tee Type Safety Heads Inlet Catalog No. psi Connection Thickness 5-6F 5,000 /6" TPER SEL HEX 5-6F2 5,000 TPER SEL " 0-6F4 0,000 TPER SEL " 0-6F6 0,000 TPER SEL " NPT Female Inlet (Straight) Safety Heads Inlet Hex Catalog No. psi Connection Length Size 5-6F 5,000 /6" TPER SEL " 5-6F2 5,000 TPER SEL " 0-6F4 0,000 TPER SEL " 0-6F6 0,000 TPER SEL " 2.6

13 Rupture Discs / 4 " ngled Seat /4 " effective area SPECIL DISCS are available on special order for pressure ranges not shown above and in numerous materials and coatings. Consult factory for price and delivery. Standard rupture discs are available from stock in burst pressures as listed in the chart below. Taper seal pressures are shaded. These discs are 6 stainless steel (except for 000 psi which are inconel) and may be used with any of the safety heads shown. Note that these rupture discs are supplied with a tolerance of plus 6% and minus % of specified burst pressure. Samples of each batch are then tested and the actual average burst pressure is stamped on an accompanying metal tag. Factors influencing rupture disc life include corrosion, metal fatigue, and cyclic effects. Periodic replacement is recommended to prevent premature failure. Standard urst s (in psi at 2 F),000,500 2,000 2,500,000,500 4,000 4,500 5,000 5,500 6,000 6,500,000,500 8,000 8,500,000,500 0,000 0,500,000,500 2,500 5,000,500 8,000 20,000 22,500 25,000 2,000 0,000 5,000,500 40,000 45,000 50,000 55,000 60,000 65,000 High Tubing Tubing is cold drawn, seamless, and is supplied in the /8 hard condition (not annealed). Tensile strength is approximately 40 percent higher than that of annealed tubing. ll tubing is manufactured in strict accordance with High Equipment Company specifications to insure tolerances and bore quality. Tubing is stocked in lengths of 8 to 22 feet but may be ordered in shorter lengths with no additional cutting charge. Note: The /6" and O.D. tubing sizes may be coiled for shipment. Larger sizes must be shipped in straight lengths. Working Type of Catalog Tubing Size psi Connection Used Material Order Number / 6 " / 8 " /6" O.D. x 0.006" I.D ,000 /6" TPER SEL (F) 6 SS /6" O.D. x 0.00" I.D O.D. x 0.060" I.D. 5,000 TPER SEL (F2) 6 SS 5-2 / 4 " O.D. x I.D. 0,000 TPER SEL (F4) 6 SS SS / 8 " O.D. x I.D. 0,000 TPER SEL (F6) 6 SS SS High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.

14 High Equipment Taper Seal Connections 0,000 and 5,000 psi service Taper Seal connections are available for /6",,, and O.D. tubing. No special tubing preparation is required simply cut tubing to desired length, deburr and assemble. The,, and sizes utilize a two-piece sleeve which is supplied partially assembled. When the connection is assembled, the outer sleeve portion is permanently compressed over the inner portion to rigidly lock the sleeve onto the tubing. Note that the sleeve is not forced to bite into the tubing, but rather is clamped onto the tubing much like a machine collet. ratings. The /6" and O.D. tubing size connections are rated to 5,000 psi working pressure. The and O.D. sizes are rated to 0,000 psi working pressure. Easy make-up connections. One of the popular benefits of taper seal connections is that it is very easy to determine when the connection is tight enough during initial assembly. Simply rotate the tubing gland into the connection until you feel a bottoming out or dead stop of the wrench. This signals that the connection has been properly made. commercial thread lubricant is highly recommended to facilitate initial makeup of the connection, but such lubrication may be removed afterwards if desired. The Taper Seal connection can be disassembled and then reassembled an indefinite number of times. Standard material for the gland is Type 6 stainless steel. The inner portion of the two-piece sleeve is Type 6 stainless steel. The nonwetted outer sleeve portion is zinc plated alloy steel. (Note that the /6" O.D. size is a one-piece sleeve design) in Type 6 stainless steel. Tubing glands and sleeves are provided with all valves and fittings unless otherwise requested. (See chart at right for size details and catalog numbers). Female Opening Detail land F /6 " O.D. Tubing Sleeve Plug 60 F2 /8 " O.D. Tubing Tubing land Sleeve 5,000 psi 0,000 psi F4 /4 " O.D. Tubing F F2 F4 F6 5-2M 5-2M2 0-2M4 0-2m THD. IN. /6".05.06" 5 /6" HEX /6" /6" 4-20 HEX 5 /6" /6" THD. IN. 5 5 /6" -6 5-M 5-M2 0-M4 0-M6 4 THD. IN. /6" HEX 2 /64" /6" 25 /64" 5 " F6 /8 " O.D. Tubing -6 4 THD. IN. /6" HEX 5 /64" /6" 5 " 2. ppendix R 5/

15 Female NPT/0,000 psi Pipe Connection Valves /8 " /4 " /8 " /2 " NPT Non-rotating tip stems are standard for on-off service and insure long life on valve seats. Regulating tip stems are available for all valves at no additional cost. Materials include high tensile Type 6 stainless steel for valve bodies, and hardened -4PH stainless steel for lower section stems. Packing is Teflon (450 F) standard with optional Viton (50 F), UN-N (200 F) and rafoil (650 F) available at no additional cost. ir operators for remote control operation are available for all valves. (See ir Operator section of catalog). NF ( ), NF ( ) and NFC ( ) NFD ( ) K Two Way Straight Valves Pipe Size Catalog No.* psi Connection Orifice D E F H J K L Thickness D F L E J H NPT NPT NPT NPT 0-NF 0-NF 0-NFC 0-NFD 0,000 0,000 0,000 0,000 NF NF NFC NFD 5 /6" /6" 2 /6" 2 /6" 5 5 /6" " " " D L E K J H Two Way ngle Valves Pipe Size Catalog No.* psi Connection Orifice D E F H J K L Thickness NPT NPT NPT NPT 0-2NF 0-2NF 0-2NFC 0-2NFD 0,000 0,000 0,000 0,000 NF NF NFC NFD 5 /6" " " " 2 /6" 2 /6" 2 /6" 5 5 /6" " " " * For valves requiring high temperature rafoil packing in the NPT, or NPT or NPT sizes, add suffix -W to catalog number. (Example 0-NF-W.) High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.

16 High Equipment Female NPT/0,000 and 5,000 psi Pipe Connection Valves /8 " /4 " /8 " /2 " NPT /4 " NPT " NPT Non-rotating tip stems are standard for on-off service and insure long life on valve seats. Regulating tip stems are available for all valves at no additional cost. Materials include high tensile Type 6 stainless steel for valve bodies, and hardened -4PH stainless steel for lower section stems. Packing is Teflon (450 F) standard with optional Viton (50 F), UN-N (200 F) and rafoil (650 F) available at no additional cost. ir operators for remote control operation are available for all valves. (See ir Operator section of catalog). NF ( ) and NF ( ) NFC ( ) and NFD ( ) NFF ( ) and NFH (" ) Two Way Straight Valves Pipe Size Catalog No.* psi Connection Orifice D E F H J K L Thickness K NPT 5F-NF 5,000 NF.20 4 /6" D L F E J H NPT NPT NPT NPT " NPT 5F-NF 5F-NFC 5F-NFD 0F-NFF 0F-NFH 5,000 5,000 5,000 0,000 0,000 NF NFC NFD NFF NFH /6" /6" /6" /6" /6" " Two Way ngle Valves Pipe Size Catalog No.* psi Connection Orifice D E F H J K L Thickness D L E K J H NPT NPT NPT NPT NPT " NPT 5F-2NF 5F-2NF 5F-2NFC 5F-2NFD 0F-2NFF 0F-2NFH 5,000 5,000 5,000 5,000 0,000 0,000 NF NF NFC NFD NFF NFH /6" 4 /6" /6" 2 5 /6" 2 /6" 2 /6" /6" /6" " * For valves requiring high temperature rafoil packing in the NPT, or NPT or NPT sizes, add suffix -W to catalog number. (Example 0-NF-W.) 2.2

17 Elbows/Tees/Crosses complete range of elbows, tees, and crosses is available for all of the tubing connection sizes. Material is high tensile 6 stainless steel. NPT Elbows E Catalog No. psi Connections - E F H Thickness H F 5-22NF 5,000 FNPT NF " " 5-22NF 5,000 FNPT NF " " " 5-22NFC 5,000 FNPT NFC " " " 5-22NFD 5,000 FNPT NFD NFF 0,000 FNPT NFF /6" 5 /6" 0-22NFH 0,000 " FNPT NFH " " 2 /6" 2 /6" NPT Tees C E H F Catalog No. psi Connections - E F H Thickness 5-2NF 5,000 FNPT NF 5-2NF 5,000 FNPT NF " " " 5-2NFC 5,000 FNPT NFC " " " 5-2NFD 5,000 FNPT NFD /6" 0-2NFF 0,000 FNPT NFF /6" 0-2NFH 0,000 " FNPT NFH 4 " 2 /6" 2 /6" C E D H F NPT Crosses Catalog No. psi Connections - E F H Thickness 5-24NF 5,000 FNPT NF 5-24NF 5,000 FNPT NF " " " 5-24NFC 5,000 FNPT NFC " " " 5-24NFD 5,000 FNPT NFD /6" 0-24NFF 0,000 FNPT NFF /6" 0-24NFH 0,000 " FNPT NFH /6" 2 /6" High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.

18 High Equipment NPT Straight Couplings Standard material is high tensile 6 stainless steel. Catalog No. psi Connections - Length Hex 5-2NF 5,000 FNPT NF 5-2NF 5,000 FNPT NF " 5-2NFC 5,000 FNPT NFC " 5-2NFD 5,000 FNPT NFD 0-2NFF 0,000 FNPT NFF 2 0-2NFH 0,000 " FNPT NFH 2 NPT ulkhead Couplings ulkhead couplings are designed specifically for passing a tubing connection through a panel or steel barricade. These couplings include a locknut as shown. Material is high tensile 6 stainless steel. Locknut Catalog No. psi Connections - Length Hex Hole Diameter 5-2NF- 5,000 FNPT NF 2 " NF- 5,000 FNPT NF 2 " NFC- 5,000 FNPT NFC 2 /6" NFD- 5,000 FNPT NFD NFF- 0,000 FNPT NFF NFH- 0,000 " FNPT NFH 2-2 NPT Caps Tubing end caps are offered for use in sealing off tubing ends either for temporary use or permanent use such as on small volume reservoirs. Standard material is high tensile 6 stainless steel. Catalog No. psi Connections - Length Hex 5-2NF-C 5,000 FNPT NF 5-2NF-C 5,000 FNPT NF " " 5-2NFC-C 5,000 FNPT NFC " 5-2NFD-C 5,000 FNPT NFD 0-2NFF-C 0,000 FNPT NFF 0-2NFH-C 0,000 " FNPT NFH 2.4 R 2/2

19 NPT Line Filters The line filters as shown utilize sintered stainless steel filter discs pc./set. Porosities are available as per the chart to the right. If not otherwise specified, 00 micron filter discs are supplied. (One micron = 0.00 millimeters). Material of body, caps and cover is hightensile 6 stainless steel. FLOW Catalog No. psi Connections - Length Hex Micron Size Filter vailable NF 5,000 FNPT NF /6" 5-5NF 5,000 FNPT NF 4 /6" 5-5NFC 5,000 FNPT NFC 4 /6" 5-5NFD 5,000 FNPT NFD 4 /6" NPT all Check Valves all type check valves insure flow in one direction only. Material for body, caps and cover is high tensile 6 stainless steel. FLOW Catalog No. psi Connections - Length Hex 5-4NF 5,000 FNPT NF 4 5 " 5-4NF 5,000 FNPT NF 4 5 " 5-4NFC 5,000 FNPT NFC 4 5 " 5-4NFD 5,000 FNPT NFD 4 /6" 0-4NFF 0,000 FNPT NFF 5 5 /6" 0-4NFH 0,000 " FNPT NFH 2 NPT Softseat Check Valves Soft seat check valves insure flow in one direction only and can be mounted in any position. These are highly reliable for both gas and liquid service. Standard O-ring (soft seat) material for the sealing surface is una-n (nitrile) with other materials including Teflon and Viton available on request. Temperature is limited by the choice of O-ring material. Material of all other parts is high tensile 6 stainless steel. FLOW Catalog No. psi Connections - Length Hex 5-4NF-T 5,000 FNPT NF 4 5 " 5-4NF-T 5,000 FNPT NF 4 5 " 5-4NFC-T 5,000 FNPT NFC 4 5 " 5-4NFD-T 5,000 FNPT NFD 4 /6" 0-4NFF-T 0,000 FNPT NFF 5 5 /6" 0-4NFH-T 0,000 " FNPT NFH 2 High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.5

20 High Equipment NPT Safety Heads The male inlet design can be inserted directly into the tubing connections of valves and various fittings such as tees and crosses, or located in pressure vessels. Outlet connections are pipe (NPT). This outlet may be connected to a suitable discharge line to vent pressure to a safe location in the event of bursting of the rupture disc. Torque required for sealing rupture discs will range from 40 to 0 foot pounds, depending upon pressure and media being used. Material of body and hold down nut is high tensile 6 stainless steel. Note: Rupture discs are not included and must be ordered as a separate item. Catalog No. psi Connections Length Hex 5-6NM 5,000 MNPT " 5-6NM 5,000 MNPT " 5-6NMC 5,000 MNPT " 5-6NMD 5,000 MNPT " Rupture Discs / 4 " ngled Seat SPECIL DISCS are available on special order for pressure ranges not shown above and in numerous materials and coatings. Consult factory for price and delivery. /4 " effective area Standard rupture discs are available from stock in burst pressures as listed in the chart below. ll pressures through 5,000 psi are shaded. These discs are 6 stainless steel (except for,000 psi which are inconel) and may be used with any of the safety heads shown. Note that these rupture discs are supplied with a tolerance of plus 6% and minus % of specified burst pressure. Samples of each batch are tested and the actual average burst pressure is stamped on an accompanying metal tag. Factors influencing rupture disc life include corrosion, metal fatigue, and cyclic effects. Periodic replacement is recommended to prevent premature failure. Standard urst s (in psi at 2 F),000,500 2,000 2,500,000,500 4,000 4,500 5,000 5,500 6,000 6,500,000,500 8,000 8,500,000,500 0,000 0,500,000,500 2,500 5,000,500 8,000 20,000 22,500 25,000 2,000 0,000 5,000,500 40,000 45,000 50,000 55,000 60,000 65,

21 High Equipment Medium Valves, Fittings and Tubing 20,000 psi service High Equipment Company has developed a line of Medium products to assure safe and easy plumbing through 20,000 psi. These needle valves, fittings, line filters, check valves, safety heads, rupture discs, anti-vibration gland assemblies, tubing and nipples are engineered to the highest standards of repeatable quality. The reliable performance of these products has made HiP one of the world s leading suppliers of elevated pressure components. Medium components use a compact coned-and-threaded connection which permits the larger bore sizes and increased flow rates common in this pressure class. Medium valves are available in,, /6",, and " O.D. tubing sizes and five patterns to satisfy widely varied requirements. line of fittings is available to facilitate adapting to Taper Seal, High or other threaded pipe systems. Index Page 20,000 psi Valves* Fittings Unions, ulkheads & Caps Line Filters & Check Valves Safety Heads & Rupture Discs..... nti-vibration land ssemblies....8 Tubing Coned & Threaded Nipples Connection Details ppendix *Note: 0,000 psi large orifice is offered in and " size. R4 2/02.

22 High Equipment LF4 ( ) and LF6 ( ) 20,000 psi Medium Valves Medium (coned & threaded) type connections for,, /6",, and " O.D. tubing. Non-rotating tip stems are standard for on-off service and insure long life on valve seats. Regulating tip stems are available for all valves at no additional cost, add - RE to part number. lands and collars for tubing are supplied with each valve unless otherwise requested (glands and collars shown on pages.4 and.). Materials include high tensile type 6 stainless steel bodies and hardened -4PH stainless steel lower section stems. Packing is Teflon (450 F) standard with optional Viton (50 F), UN-N (200 F) and rafoil (800 F) available at no additional cost. ir operators for remote control operation are available for all valves. (Select required valve and add HIPCO. Refer to section.0 for additional data). High temperatures can be accommodated by using extended stuffing boxes (see page 6.6). LF ( /6") Valve Features Non-rotating stem tips Packing below stem threads Type 6 ss high tensile bodies Positive gland lock device No stem adjustment needed lack T-handles or choice of 4 colors Tube sizes through " LF2 ( ) and LF6 (")* *Note: 0,000 psi large orifice is offered in and " size..2 R5 8/04

23 20,000 psi Medium Valves Two Way Straight Valves D L F E K J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 20-LF4 20,000 LF4 4 /6" O.D. 20-LF6 20,000 LF6 /64" 4 /6" /6" O.D. 20-LF 20,000 LF 5 /6" " O.D. 20-LF2 20,000 LF2 /6" " " 5 /6" O.D. 0-LF2 0,000 LF2 /64" " " 5 /6" " O.D. 20-LF6 20,000 LF6 /6" 8 2 /64" 4 /6" /6" " O.D. 0-LF6 0,000 LF6 /6" 8 2 /64" 4 /6" /6" Two Way ngle Valves D L E K J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 20-2LF4 20,000 LF4 4 /6" _ 2 /6" O.D. 20-2LF6 20,000 LF6 4 /6" _ /64" 2 /6" /6" O.D _ 20-2LF 20,000 LF /6" 5 " O.D. 20-2LF2 20,000 LF2 " _ /6" 4 5 /6" O.D. 0-2LF2 0,000 LF2 " _ /64" 4 5 /6" " O.D. 20-2LF6 20,000 LF6 4 _ /6" 2 /6" 5 /6" 2 /6" " O.D. 0-2LF6 0,000 LF6 4 _ /6" 2 /6" 5 /6" 2 /6" Three Way Valves / Two Connections D L F D L F J F L D K F J D L E E E E K J H K J H H K J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 20-LF4 20,000 LF4 5" " /6" 2 5 O.D. 20-LF6 20,000 LF6 /64" 5" " /6" 2 5 /6" O.D. 20-LF 20,000 LF 5 /6" " O.D. 20-LF2 20,000 LF2 /6" " /6" O.D. 0-LF2 0,000 LF2 /64" " /6" " O.D. 20-LF6 20,000 LF6 /6" 4 2 /6" 5 2 /6" " O.D. 0-LF6 0,000 LF6 /6" 4 2 /6" 5 2 /6" Three Way Valves / One Connection Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 20-4LF4 20,000 LF4 4 /6" 2 /6" O.D. 20-4LF6 20,000 LF6 /64" 4 /6" 2 /6" /6" O.D. 20-4LF 20,000 LF 5 /6" " O.D. 20-4LF2 20,000 LF2 /6" " 4 5 /6" O.D. 0-4LF2 0,000 LF2 /64" " 4 5 /6" " O.D. 20-4LF6 20,000 LF6 /6" /6" 2 /6" " O.D. 0-4LF6 0,000 LF6 /6" /6" 2 /6" Three Way / Two Stem Connection Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 20-5LF4 20,000 LF4 5 /6" /6" O.D. 20-5LF6 20,000 LF6 /64" 5 /6" /6" /6" O.D. 20-5LF 20,000 LF 5 /6" /6" 5 " O.D. 20-5LF2 20,000 LF2 /6" " /6" O.D. 0-5LF2 0,000 LF2 /64" " /6" " O.D. 20-5LF6 20,000 LF6 /6" 2 /6" /6" 8 2 /6" " O.D. 0-5LF6 0,000 LF6 /6" 2 /6" /6" 8 2 /6" Replaceable Seat Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 20-2LF4-R 20,000 LF4 5 5 _ 2 /6" O.D. 20-2LF6-R 20,000 LF6 5 5 _ /64" 2 /6" /6" O.D. 5 8" 2 _ 20-2LF-R 20,000 LF /6" 5 " O.D. 20-2LF2-R 20,000 LF2 8 " _ /6" 4 5 /6" O.D. 0-2LF2-R 0,000 LF2 8 " _ /64" 4 5 /6" " O.D. 20-2LF6-R 20,000 LF6 /6" /6" 4 _ /6" 2 /6" 5 /6" 2 /6" " O.D. 0-2LF6-R 0,000 LF6 /6" /6" 4 _ 2 /6" 5 /6" 2 /6" High Equipment Company R 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

24 High Equipment lands/collars/plugs Elbows/Tees/Crosses complete range of elbows, tees, and crosses is available for all of the tubing connection sizes. Material is high tensile 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. Connection Components Tube Catalog No. Size land 20-2LM4 20-2LM6 Tube Catalog No. Size Collar 20-2L4 20-2L6 Tube Catalog No. Size Plug 20-LM4 20-LM6 20-2LM /6" 20-2LM2 20-2LM6 " 20-2L /6" 20-2L2 20-2L6 " 20-LM /6" 20-LM2 20-LM6 " Medium Elbows E Catalog No. psi Connections - E F H Thickness H F 20-22LF4 20,000 O.D. TUE LF4 /6" " /6" LF6 20,000 O.D. TUE LF6 " " 20-22LF 20,000 /6" O.D. TUE LF " 20-22LF2 20,000 O.D. TUE LF LF6 20,000 " O.D. TUE LF6 " " 2 /6" 2 /6" C E H F Medium Tees Catalog No. psi Connections --C E F H Thickness 20-2LF4 20,000 O.D. TUE LF4 " /6" LF6 20,000 O.D. TUE LF6 " " 20-2LF 20,000 /6" O.D. TUE LF 2 " 20-2LF2 20,000 O.D. TUE LF2 " LF6 20,000 " O.D. TUE LF6 4 " 2 /6" 2 /6" C E D H F Medium Crosses Catalog No. psi Connections --C-D E F H Thickness 20-24LF4 20,000 O.D. TUE LF4 /6" LF6 20,000 O.D TUE LF6 " " 20-24LF 20,000 /6" O.D. TUE LF 2 2 " 20-24LF2 20,000 O.D. TUE LF2 " " 20-24LF6 20,000 " O.D. TUE LF /6" 2 /6".4 R2 2/

25 Union Couplings (Slip Type) Union (slip type) couplings are ideal for use in confined space installations. This design allows the entire coupling to be disconnected and slipped back over the tubing to facilitate assembly and disassembly. In installations where tubing is easily assembled, it is preferable (and less expensive) to use standard straight couplings (see section 8.0). Standard material is high tensile 6 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. ulkhead Couplings ulkhead couplings are designed specifically for passing a tubing connection through a panel or steel barricade. These couplings include a locknut as shown. Material is high tensile 6 stainless steel. Standard tubing collars and glands are included unless otherwise specified. Catalog No. Tubing psi Orifice Length Hex 20-2LF4-U O.D. 20,000 LF4 LF4 /6" LF6-U O.D. 20,000 LF6 LF6 20-2LF-U /6" O.D. 20,000 LF LF 2 /64" LF2-U O.D. 20,000 LF2 LF2 /64" LF6-U " O.D. 20,000 LF6 LF6 /6" Catalog No. Tubing psi Connections Orifice Length Hex Hole Diameter 20-2LF4- O.D. 20,000 LF4 " LF6- O.D. 20,000 LF6 " LF- /6" O.D. 20,000 LF 2 /64" 2 /6" LF2- O.D. 20,000 LF2 /64" LF6- " O.D. 20,000 LF-6 /6" 2-2 Locknut Caps Tubing end caps are offered for use in sealing off tubing ends either for temporary use or permanent use such as on small volume reservoirs. Standard material is high tensile 6 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. Catalog No. Tubing psi Length Hex 20-2LF4-C O.D. 20,000 LF LF6-C O.D. 20,000 LF6 20-2LF-C /6" O.D. 20,000 LF " 20-2LF2-C O.D. 20,000 LF LF6-C " O.D. 20,000 LF6 " High Equipment Company R 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

26 High Equipment Line Filters The line filters as shown utilize sintered stainless steel filter discs 4 pc./set. Porosities are available as per the chart to the right. If not otherwise specified, 00 micron filter discs are supplied. (One micron = 0.00 millimeters). Material of body, caps and cover is high tensile 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. FLOW Micron Size Filter vailable Catalog No. Tubing psi Connections Orifice Length Thickness LF4 O.D. 20,000 LF LF6 O.D. 20,000 LF LF /6" O.D. 20,000 LF 2 /64" 5 all Check Valves all type check valves insure flow in one direction only. Material for body, caps and cover is high tensile 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. Note: 20-4LF6 material -4PH Soft Seat Check Valves Soft seat check valves insure flow in one direction only and can be mounted in any position. These are highly reliable for both gas and liquid service. Standard O-ring (soft seat) material for the sealing surface is una-n (nitrile) with other materials including Teflon and Viton available on request. Temperature is limited by the choice of O-ring material. Material of all other parts is high tensile 6 stainless steel. Standard glands and collars are provided unless otherwise specified. Note: 20-4LF6 material -4PH FLOW Catalog No. Tubing psi Connections Orifice Length Thickness 20-4LF4 O.D. 20,000 LF4 " 20-4LF6 O.D. 20,000 LF6 " 20-4LF /6" O.D. 20,000 LF 2 /64" LF2 O.D. 20,000 LF2 /6" LF6 " O.D. 20,000 LF6 /6" 6 2 FLOW Catalog No. Tubing psi Connections Orifice Length Thickness 20-4LF4-T O.D. 20,000 LF4 " 20-4LF6-T O.D. 20,000 LF6 " 20-4LF-T /6" O.D. 20,000 LF 2 /64" LF2-T O.D. 20,000 LF2 /6" LF6-T " O.D. 20,000 LF6 /6" R 2/

27 Safety Heads The male inlet design can be inserted directly into the tubing connections of valves and various fittings such as tees and crosses, or located in pressure vessels. Outlet connections are pipe (NPT). This outlet may be connected to a suitable discharge line to vent pressure to a safe location in the event of bursting of the rupture disc. Torque required for sealing rupture discs will range from 40 to 0 foot pounds, depending upon pressure and media being used. Material of body and hold down nut is high tensile 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. Note: Rupture discs are not included and must be ordered as a separate item. Catalog No. Tubing psi Connections Orifice Length Hex 20-6LM4 O.D. 20,000 LM4 0.25" " 20-6LM6 O.D. 20,000 LM6 0. " 20-6LM /6" O.D. 20,000 LM 0.250" 2 " 20-6LM2 O.D. 20,000 LM " LM6 " O.D. 20,000 LM " Rupture Discs / 4 " ngled Seat /4 " effective area SPECIL DISCS are available on special order for pressure ranges not shown above and in numerous materials and coatings. Consult factory for price and delivery. Standard rupture discs are available from stock in burst pressures as listed in the chart below. ll pressures through 20,000 psi are shaded. These discs are 6 stainless steel (except for,000 psi which are inconel) and may be used with any of the safety heads shown. Note that these rupture discs are supplied with a tolerance of plus 6% and minus % of specified burst pressure. Samples of each batch are tested and the actual average burst pressure is stamped on an accompanying metal tag. Factors influencing rupture disc life include corrosion, metal fatigue, and cyclic effects. Periodic replacement is recommended to prevent premature failure. Standard urst s (in psi at 2 F),000,500 2,000 2,500,000,500 4,000 4,500 5,000 5,500 6,000 6,500,000,500 8,000 8,500,000,500 0,000 0,500,000,500 2,500 5,000,500 8,000 20,000 22,500 25,000 2,000 0,000 5,000,500 40,000 45,000 50,000 55,000 60,000 65,000 High Equipment Company R5 /0 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

28 High Equipment nti-vibration land ssemblies Tubing systems that are subject to extreme vibration or shock, such as mobile pressure systems or long tubing runs culminating at a compressor, will benefit from the use of High Equipment Company's nti-vibration land ssemblies. These assemblies utilize the same reliable connection geometries as the standard HiP fittings, with the added benefit of essentially unlimited vibrational fatigue life. coned and threaded tube, when subjected to unusual or excessive vibration, may fail prematurely and break at the last thread. The nti-vibration land ssembly acts to move the fulcrum of vibration away from the threaded portion of the tube and onto the strong, solid wall of the tubing. wedge-like collet firmly holds the assembly in place, virtually eliminating premature tubing failure while reliably maintaining a leak-free connection between the tube and the connection seat. Medium nti-vibration land ssemblies Catalog No. psi Connections C 20-LM4 20,000 MEDIUM PRESSURE 5 /6" 20-LM6 20,000 MEDIUM PRESSURE LM 20,000 /6" MEDIUM PRESSURE " 20-LM2 20,000 MEDIUM PRESSURE 2 20-LM6 20,000 " MEDIUM PRESSURE 2 C nti-vibration Components Tubing Slotted Collet Collet Size Collet land ody Collar /4 " L4 /8 " /6 " /4 " " L L L L6.8

29 Medium Tubing Tubing is cold drawn, seamless, and is supplied in the /8 hard condition (not annealed). Tensile strength is approximately 40 percent higher than that of annealed tubing. ll tubing is manufactured in strict accordance with High Equipment Company specifications to insure tolerances and bore quality. Tubing is stocked in lengths of 8 to 22 feet but may be ordered in shorter lengths with no additional cutting charge. / 4 " / 8 " Working Type of Catalog Tubing Size psi Connection Used Material Order Number O.D. x 0.0" I.D. 20,000 MEDIUM PRESSURE (LF4) 6 SS 20-M4-6 O.D. x 0.20" I.D. 20,000 MEDIUM PRESSURE (LF6) 6 SS 20-M6-6 / 6 " / 4 " /6" O.D. x 0.5" I.D. 0,000 6 SS 0-M-6 /6" MEDIUM PRESSURE (LF) /6" O.D. x 0. I.D. 20, SS 20-M-04 6 SS 20-M-6 O.D. x 0.56" I.D. 0,000 0-M2-6 MEDIUM PRESSURE (LF2) 6 SS O.D. x 0.48" I.D. 20, M2-6 " " O.D. x 0.688" I.D. 0,000 0-M6-6 " MEDIUM PRESSURE (LF6) 6 SS " O.D. x 0.56 I.D. 20, M6-6 Nipples Nipples are stocked in 6 stainless steel. Nipples in lengths other than those shown are supplied upon request. Nipples are not furnished with collars and glands, unless specified at time of order. Length Coned and Threaded Nipples Tubing Size (O.D. x I.D.) O.D. x /64" I.D. O.D. x /64" I.D. /6" O.D. x 5 /6" I.D. O.D. x /64" I.D. O.D. x /6" I.D. " O.D. x /6" I.D. " O.D. x /6" I.D. psi 2 " 4" 6" 8" 0" 20,000 psi 20-LM LM LM LM LM4-2 20,000 psi 20-LM6-20-LM LM LM LM6-2 20,000 psi 20-LM-4 20-LM-6 20-LM-8 20-LM-0 20-LM-2 0,000 psi 0-LM2-4 0-LM2-6 0-LM2-8 0-LM2-0 0-LM2-2 20,000 psi 20-LM LM LM LM2-2 0,000 psi 0-LM6-6 0-LM6-8 0-LM6-0 0-LM6-2 20,000 psi 20-LM LM LM LM6-2 High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

30 High Equipment Medium Connections (Coned and Threaded) 20,000 psi service The Medium tubing connection is available for,, /6", and " O.D. tubing. The tubing may be prepared with the use of tooling (see tooling section.0) or prepared at the factory to specified lengths. dditionally, standard length coned and threaded nipples are available from stock (see page.). This connection has become an industry standard for use at elevated pressures and temperatures in both liquid and gas applications. It may be disassembled and retightened indefinitely. The threads of the gland are right-hand while the threads of the collar and tubing are left-hand to prevent rotation of the collar during assembly. LF4 /4 " O.D. Tubing Female Opening Detail /6" LF6 /8 " O.D. Tubing 60 /6 " - 8 5/8 " LF /6 " O.D. Tubing /6 " ,000 psi /4 " LF2 /4 " O.D. Tubing /4 " - 4 NPSM 60 5/6 " LF6 " O.D. Tubing - /8 " - 2 TH'D 60-5 /6 " Materials. ll of the components required for make-up of a Medium connection (glands, collars and plugs) are produced in Type 6 stainless steel. lands and collars are provided with all valves and fittings (except nipples) unless otherwise requested. (See chart on the right for size details and catalog numbers). LF4 LF6 LF LF2 LF6 land /6" /6" /6" NPSM LM4 20-2LM6 20-2LM 20-2LM2 20-2LM6 - Collar -24 L.H. /6" -8 L.H. -6 L.H. "-4 L.H. -28 L.H. Plug /6" /6" 20-2L4 20-2L6 20-2L 20-2L2 20-2L6 " /2 " /6 " /6" - 2 /64 " 2 /6" /2 " -/6" 5/6" -/6" 5 /8 " - HEX 5/6" /64 " /8 " - HEX /6 " - -/6" 2- Tubing land Collar 20-LM4 20-LM6 20-LM 20-LM2 20-LM6 Tube End Prep 5 /64" /6 " /4 " /2 " 5 5 /2 " 5/8 " - 28 L.H. /8 " - 24 L.H. /6 " - 8 L.H. /4 LM4 LM6 LM LM2 " - 6 L.H. LM6 /6 " /6" /2 " /6 " 2/2 " " - 4 L.H.. ppendix R2 2/

31 High Equipment High Valves, Fittings and Tubing 0,000, 40,000 and 60,000 psi service High Equipment Company has developed a line of High products to assure safe and easy plumbing for 0,000, 40,000 and 60,000 psi. These needle valves, fittings, line filters, check valves, safety heads, rupture discs, anti-vibration gland assemblies, tubing and nipples are engineered to the highest standards of repeatable quality. The reliable performance of these products has made HiP one of the world s leading suppliers of elevated pressure components. High components use a coned-and-threaded connection which accommodates the high temperatures and pressures common in these applications. High valves are available in various tubing sizes and with body designs to satisfy widely varied requirements. line of fittings is available to facilitate adapting to Taper Seal, Medium, or other High threaded pipe systems. Index Page 0,000 psi Valves ,000 psi Valves ,000 psi Valves Fittings Unions, ulkheads & Caps Line Filters & Check Valves Rupture Discs Safety Heads nti-vibration land ssemblies..4. Tubing Coned & Threaded Nipples Connection Details ppendix R2 2/ 4.

32 High Equipment HF2 ( ) 0,000 psi High Valves High (coned & threaded) type connections for,,, /6" and " O.D. tubing. Non-rotating tip stems are standard for on-off service and insure long life on valve seats. Regulating tip stems are available for all valves at no additional cost, add - RE to part number. lands and collars for tubing are supplied with each valve unless otherwise requested (glands and collars shown on pages 4.6 and 4.). Materials include high tensile type 6 stainless steel bodies and hardened -4PH stainless steel lower section stems. Packing is Teflon (450 F) standard with optional Viton (50 F), UN-N (200 F) and rafoil (800 F) available at no additional cost. ir operators for remote control operation are available for all valves. (Select required valve and add HIPCO. Refer to section.0 for additional data). High temperatures can be accommodated using extended stuffing boxes (see page 6.6). These are available for all sizes except tubing. To order, add suffix -HT to standard valve catalog number. HF4 ( ), HF6 ( ) and HF ( /6") Valve Features Non-rotating stem tips Packing below stem threads Type 6 ss high tensile bodies Positive gland lock device No stem adjustment needed lack T-handles or choice of 4 colors Tube sizes through /6" HF6 (") 4.2 R2 2/

33 0,000 psi High Valves Two Way Straight Valves K Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 0-HF2 0,000 HF2 /6" 5 /6" /6" /6" 5 /6" /64" D L F E J H O.D. O.D. /6" O.D. " O.D. 0-HF4 0-HF6 0-HF 0-HF6 0,000 0,000 0,000 0,000 HF4 HF6 HF HF6 /6" 5 /6" 5 /6" /64" " 5 /6" " " /6" /6" 2 /6" 2 /6" 2 4 /6" 2 /6" " " Two Way ngle Valves D L E K J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. O.D. /6" O.D. " O.D. 0-2HF2 0-2HF4 0-2HF6 0-2HF 0-2HF6 0,000 0,000 0,000 0,000 0,000 HF2 HF4 HF6 HF HF6 /6" /6" 5 /6" 5 /6" _ 5 /6" " /6" 2 /6" 2 /6" 2 /6" /6" 2 /64" /6" " " Three Way Valves / Two Connections D L F E K J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 0-HF2 0,000 O.D. 0-HF4 0,000 O.D. 0-HF6 0,000 /6" O.D. 0-HF 0,000 HF2 HF4 HF6 HF " O.D. 0-HF6 0,000 HF6 /6" /6" 5 /6" 5 /6" 6 /6" 2 5 " 2 5 /6" /6" /6" /6" 5 /6" " 2 /6" 2 /6" 5 /6" 2 /6" 5 /6" 2 /64" /6" " " Three Way Valves / One Connection K Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness D F L E J H O.D. O.D. O.D. /6" O.D. " O.D. 0-4HF2 0-4HF4 0-4HF6 0-4HF 0-4HF6 0,000 0,000 0,000 0,000 0,000 HF2 HF4 HF6 HF HF6 /6" /6" 5 /6" 5 /6" /6" " 2 /6" 2 5 /6" " /6" /6" 2 /6" 2 /6" 2 /6" /6" 2 /64" /6" " " Three Way / Two Stem Connection Valves J F L D K F J E H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 0-5HF2 0,000 O.D. 0-5HF4 0,000 O.D. 0-5HF6 0,000 /6" O.D. 0-5HF 0,000 HF2 HF4 HF6 HF " O.D. 0-5HF6 0,000 HF6 /6" " /6" /6" 5 /6" 2 /6" 2 /6" /6" /6" 5 /6" 4" 4 2 " /64" /6" " " K Replaceable Seat Valves D L E J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. /6" O.D. " O.D. 0-2HF4-R 0-2HF6-R 0-2HF-R 0-2HF6-R 0,000 0,000 0,000 0,000 HF4 HF6 HF HF6 /6" 6" /6" " /6" 2 2 /6" 2 /6" /6" " " High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 4.

34 High Equipment 40,000 psi High Valves High (coned & threaded) type connections for /6" O.D. tubing. Non-rotating tip stems are standard for on-off service and insure long life on valve seats. Regulating tip stems are available for all valves at no additional cost, add - RE to part number. lands and collars for tubing are supplied with each valve unless otherwise requested (glands and collars shown on pages 4.6 and 4.). Materials include high tensile type 6 stainless steel bodies and hardened -4PH stainless steel lower section stems. Packing set consists of multiple Teflon packing with nylon back up, with optional Viton (50 F), UN-N (200 F) and rafoil (800 F) available at no additional cost. ir operators for remote control operation are available for all valves. (Select required valve and add HIPCO. Refer to section.0 for additional data). High temperatures can be accommodated using extended stuffing boxes (see page 6.6). Valve Features Non-rotating stem tips Packing below stem threads Type 6 ss high tensile bodies Positive gland lock device No stem adjustment needed lack T-handles or choice of 4 colors 4..5 R2 2/

35 40,000 psi High Valves D L K J H Two Way Straight Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 40-HF 40,000 HF " /6" 2 5 F E D L K J H Two Way ngle Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 40-2HF 40,000 HF _ /6" 2 5 E D L K J H Three Way Valves / Two Connections Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 40-HF 40,000 HF 6 /6" 2 5 /6" 5 /6" 5 F E D F L K J H Three Way Valves / One Connection Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 40-4HF 40,000 HF /6" /6" 2 5 E J F L D K F J H Three Way / Two Stem Connection Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 40-5HF 40,000 HF /6" /6" 4 E D L K J H Replaceable Seat Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness /6" O.D. 40-2HF-R 40,000 HF _ /6" 2 5 E High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

36 High Equipment 60,000 psi High Valves High (coned & threaded) type connections for,,, /6" and " O.D. tubing. Non-rotating tip stems are standard for on-off service and insure long life on valve seats. Regulating tip stems are available for all valves at no additional cost, add - RE to part number. lands and collars for tubing are supplied with each valve unless otherwise requested (glands and collars shown on pages 4.6 and 4.). Materials include high tensile type 6 stainless steel bodies and hardened -4PH stainless steel lower section stems. Packing set consists of multiple Teflon packing with nylon back up, with optional Viton (50 F), UN-N (200 F) and rafoil (800 F) available at no additional cost. ir operators for remote control operation are available for all valves. (Select required valve and add HIPCO. Refer to section.0 for additional data). High temperatures can be accommodated using extended stuffing boxes (see page 6.6). These are available for all sizes except tubing. Valve Features Non-rotating stem tips Packing below stem threads Type 6 ss high tensile bodies Positive gland lock device No stem adjustment needed lack T-handles or choice of 4 colors Tube sizes through /6" 4.4 R2 2/

37 60,000 psi High Valves D L F E K J H Two Way Straight Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 60-HF2 60,000 HF2 O.D. 60-HF4 60,000 HF4 O.D. 60-HF6 60,000 HF6 /6" O.D. 60-HF 60,000 HF /6" 5 /6" /6" 5 /6" /6" 5 /6" /6" " 5 /6" 2 /6" " " /6" 2 /6" 2 /6" 2 " " " D L E K J H Two Way ngle Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. O.D. /6" O.D. 60-2HF2 60-2HF4 60-2HF6 60-2HF 60,000 60,000 60,000 60,000 HF2 HF4 HF6 HF /6" /6" /6" /6" 5 /6" 5 /6" 5 /6" " " /6" 2 /6" 2 /6" 2 /6" 2 " " " K Three Way Valves / Two Connections D L J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 60-HF2 60,000 HF2 /6" 5 /6" 5 " 2 /6" " O.D. 60-HF4 60,000 HF4 /6" 5 /6" 5 " 2 /6" " F E O.D. /6" O.D. 60-HF6 60-HF 60,000 60,000 HF6 HF /6" /6" 5 /6" 6 /6" 2 5 " /6" 2 /6" 5 /6" " K Three Way Valves / One Connection D F L J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 60-4HF2 60,000 HF2 O.D. 60-4HF4 60,000 HF4 /6" 5 /6" /6" 5 /6" " " 2 /6" 2 /6" " " E O.D. /6" O.D. 60-4HF6 60-4HF 60,000 60,000 HF6 HF /6" /6" 5 /6" /6" /6" 2 /6" 2 " J F L D K F J E H Three Way / Two Stem Connection Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. 60-5HF2 60,000 HF2 O.D. 60-5HF4 60,000 HF4 O.D. 60-5HF6 60,000 HF6 /6" O.D. 60-5HF 60,000 HF /6" /6" /6" /6" /6" /6" /6" /6" /6" 4" " " " " D L E K J H Replaceable Seat Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. 60-2HF4-R 60-2HF6-R 60,000 60,000 HF4 HF6 /6" /6" 6" 6 5 " 2 /6" 2 /6" " " 60-2HF-R 60,000 HF /6" 6 /6" 2 5 _ /6" 2 /6" O.D. High Equipment Company R 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 4.5

38 High Equipment lands/sleeves/plugselbows/tees/crosses complete range of elbows, tees, and crosses is available for all of the tubing connection sizes. Material is high tensile 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. Connection Components Tube Catalog No. Size land 60-2HM2 60-2HM4 60-2HM6 60-2HM /6" 40-2HM /6" 0-2HM6 " Tube Catalog No. Size Collar 60-2H2 60-2H4 60-2H6 60-2H /6" 40-2H /6" 0-2H6 " Tube Catalog No. Size Plug 60-HM2 60-HM4 60-HM6 60-HM /6" 40-HM /6" 0-HM6 " E H High Elbows Catalog No. psi Connections - E F H Thickness 60-22HF2 60,000 O.D. TUE HF HF4 60,000 O.D. TUE HF4 " " F 60-22HF6 60,000 O.D. TUE HF6 " " 60-22HF 60,000 /6" O.D. TUE HF HF 40,000 /6" O.D. TUE HF HF6 0,000 " O.D. TUE HF6 " " 2 /6" 2 /6" C E H F High Tees Catalog No. psi Connections --C E F H Thickness 60-2HF2 60,000 O.D.TUE HF2 60-2HF4 60,000 O.D.TUE HF4 " " 60-2HF6 60,000 O.D.TUE HF6 /6" " /6" " 60-2HF 60,000 /6" O.D.TUE HF /6" 40-2HF 40,000 /6" O.D.TUE HF /6" 0-2HF6 0,000 " O.D. TUE HF6 4 " 2 /6" 2 /6" C E D H F High Crosses Catalog No. psi Connections --C-D E F H Thickness 60-24HF2 60,000 O.D. TUE HF HF4 60,000 O.D. TUE HF4 " " 60-24HF6 60,000 O.D. TUE HF6 2 /6" " " 60-24HF 60,000 /6" O.D. TUE HF /6" 40-24HF 40,000 /6" O.D. TUE HF /6" 0-24HF6 0,000 " O.D. TUE HF /6" 2 /6" 4.6 R 8/04

39 Union Couplings (Slip Type) Union (slip type) couplings are ideal for use in confined space installations. This design allows the entire coupling to be disconnected and slipped back over the tubing to facilitate assembly and disassembly. In installations where tubing is easily assembled, it is preferable (and less expensive) to use standard straight couplings (see accessories section). Standard material is high tensile 6 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. ulkhead Couplings ulkhead couplings are designed specifically for passing a tubing connection through a panel or steel barricade. These couplings include a locknut as shown. Material is high tensile 6 stainless steel. Standard tubing collars and glands are included unless otherwise specified. Hex Catalog No. psi Connections Length Size 60-2HF2-U 60,000 O.D. TUIN HF2 HF2 60-2HF4-U 60,000 O.D. TUIN HF4 HF4 " 60-2HF6-U 60,000 O.D. TUIN HF6 HF6 " 60-2HF-U 60,000 /6" O.D. TUIN HF HF HF-U 40,000 /6" O.D. TUIN HF HF 2 0-2HF6-U 0,000 " O.D. TUIN HF6 HF6 Locknut Panel Hex Outside Catalog No. psi Connections Hole Length Size Thread 60-2HF2-60,000 O.D. TUIN 5 /6" HF2 HF2 " HF4-60,000 O.D. TUIN 5 /6" HF4 HF4 " HF6-60,000 O.D. TUIN HF6 HF6 2 /6" HF- 60,000 /6" O.D. TUIN /6" HF HF HF- 40,000 /6" O.D. TUIN /6" HF HF HF6-0,000 " O.D. TUIN 5 /6" HF6 HF Caps Tubing end caps are offered for use in sealing off tubing ends either for temporary use or permanent use such as on small volume reservoirs. Standard material is high tensile 6 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. Hex Catalog No. psi Connections Length Size 60-2HF2-C 60,000 O.D. TUIN HF2 60-2HF4-C 60,000 O.D. TUIN HF4 60-2HF6-C 60,000 O.D. TUIN HF6 " 60-2HF-C 60,000 /6" O.D. TUIN HF 40-2HF-C 40,000 /6" O.D. TUIN HF 0-2HF6-C 0,000 " O.D. TUIN HF6 " High Equipment Company R / 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 4.

40 Line Filters The line filters as shown utilize sintered stainless steel filter discs pc./set. Porosities are available as per the chart to the right. If not otherwise specified, 00 micron filter discsare supplied. (One micron = 0.00 millimeters). Material of bodies and end covers is high tensile 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. all Check Valves all type check valves insure flow in one direction only. Material for bodies and covers is 6 stainless steel (0-4HF6 body and cover are -4PH). Standard tubing glands and collars are provided unless otherwise specified. Soft Seat Check Valves Soft seat check valves insure flow in one direction only and can be mounted in any position. These are highly reliable for both gas and liquid service. Standard O-ring (soft seat) material for the sealing surface is una-n (nitrile) with other materials including Teflon and Viton available on request. Temperature is limited by the choice of O-ring material. Material of all other parts is high tensile 6 stainless steel. (0-4HF6-T body and cover are -4PH). Standard glands and collars are provided unless otherwise specified. High Equipment Catalog No. psi Connections Length Hex 40-4HF 40,000 /6" HIH PRESSURE HF2 60,000 HIH PRESSURE 4 /6" 60-4HF4 60,000 HIH PRESSURE HF6 60,000 HIH PRESSURE HF 60,000 /6" HIH PRESSURE 5 0-4HF6 0,000 " HIH PRESSURE 6 2 RD with flats FLOW Micron Size Filter Hex vailable Catalog No. psi Connections Length Size F-5HF 40,000 /6" HIH PRESSURE 5 60F-5HF2 60,000 HIH PRESSURE 4 /6" 60F-5HF4 60,000 HIH PRESSURE 4 60F-5HF6 60,000 HIH PRESSURE 5 60F-5HF 60,000 /6" HIH PRESSURE 5 FLOW FLOW Catalog No. psi Connections Length Hex 0-4HF2-T 0,000 HIH PRESSURE " 0-4HF4-T 0,000 HIH PRESSURE " 0-4HF6-T 0,000 HIH PRESSURE " 0-4HF-T 0,000 /6" HIH PRESSURE HF-T 40,000 /6" HIH PRESSURE 5 /6" 60-4HF4-T 60,000 HIH PRESSURE 4 /6" 60-4HF6-T 60,000 HIH PRESSURE 4 /6" 60-4HF-T 60,000 /6" HIH PRESSURE 5 /6" 0-4HF6-T 0,000 " HIH PRESSURE 6 2 RD with flats 4.8 R2 2/

41 Excess Surge Check Valves Excess surge check valves are used to eliminate loss of pressure due to a sudden surge or opening of a pressure component in a pressurized system (such as a breakage of a gauge or test component). These check valves should be mounted in the vertical position. Only one basic size is available (60-4HF-E) with adapters readily available to convert to other size connections. Standard tubing glands and collars are provided unless otherwise specified. FLOW Catalog No. psi Connections Length Hex 60-4HF-E 60,000 /6" HIH PRESSURE Rupture Discs /4 " ngled Seat Standard rupture discs are available from stock in burst pressures as listed in the chart to the right. These discs are 6 stainless steel (except for 000 psi which are inconel) and may be used with any of the safety heads shown. Note that these rupture discs are manufactured with a tolerance of plus 6% and minus % of specified burst pressure. Samples of each batch are then tested and the actual average burst pressure is stamped on the accompanying metal tag. Factors influencing rupture disc life include corrosion, metal fatigue, and cyclic effect. Periodic replacement is recommended to prevent premature failure. It is recommended that working pressure does not exceed 0% of burst rating for maximum life cycle of the disc.,000,500 2,000 2,500,000,500 4,000 4,500 /4 " effective area 5,000 5,500 6,000 6,500,000,500 8,000 8,500,000,500 0,000 0,500 SPECIL DISCS are available on special order for pressure ranges not shown above and in numerous materials and coatings. Consult factory for price and delivery. Standard urst s (in psi at 2 F),000,500 2,500 5,000,500 8,000 20,000 22,500 25,000 2,000 0,000 5,000,500 40,000 45,000 50,000 55,000 60,000 65,000 High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 4.

42 High Equipment Safety Heads choice of three safety head designs is available, male inlet, female inlet (straight), and tee type. The male inlet design can be inserted directly into the tubing connections of valves and various fittings such as tees and crosses, or located in pressure vessels. Outlet connections on all sizes are pipe (NPT). This outlet may be connected to a suitable discharge line to vent pressure to a safe location in the event of bursting of the rupture disc. Torque required for sealing rupture discs will range from 40 to 0 foot pounds, depending upon pressure and media being used. Material of bodies and hold down nuts is high tensile 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. Note: Rupture discs are not included and must be ordered as a separate item. NPT Male Inlet Safety Heads Inlet Hex Catalog No. psi Connection Length Size 60-6HM4 60,000 HIH PRESSURE 60-6HM6 60,000 HIH PRESSURE HM 60,000 /6" HIH PRESSURE HM 40,000 /6" HIH PRESSURE 2 0-6HM6 0,000 " HIH PRESSURE NPT Tee Type Safety Heads Inlet Catalog No. psi Connection Thickness 60-6HF2 60,000 HIH PRESSURE " 60-6HF4 60,000 HIH PRESSURE " 60-6HF6 60,000 HIH PRESSURE " 60-6HF 60,000 /6" HIH PRESSURE HF 40,000 /6" HIH PRESSURE 2 5 NPT Female Inlet (Straight) Safety Heads Inlet Hex Catalog No. psi Connection Length Size 60-6HF2 60,000 HIH PRESSURE 60-6HF4 60,000 HIH PRESSURE 60-6HF6 60,000 HIH PRESSURE 60-6HF 60,000 /6" HIH PRESSURE HF 40,000 /6" HIH PRESSURE R2 2/

43 nti-vibration land ssemblies Tubing systems that are subject to extreme vibration or shock, such as mobile pressure systems or long tubing runs culminating at a compressor, will benefit from the use of High Equipment Company's nti-vibration land ssemblies. These assemblies utilize the same reliable connection geometries as the standard HiP fittings, with the added benefit of essentially unlimited vibrational fatigue life. coned and threaded tube, when subjected to unusual or excessive vibration, may fail prematurely and break at the last thread. The nti- Vibration land ssembly acts to move the fulcrum of vibration away from the threaded portion of the tube and onto the strong, solid wall of the tubing. wedge-like collet firmly holds the assembly in place, virtually eliminating premature tubing failure while reliably maintaining a leak-free connection between the tube and the connection seat. High nti-vibration land ssemblies Catalog No. psi Connections 60-HM4 60,000 HIH PRESSURE 5 /6" 60-HM6 60,000 HIH PRESSURE /6" 60-HM 60,000 /6" HIH PRESSURE /6" /6" 40-HM 40,000 /6" HIH PRESSURE /6" /6" nti-vibration Components Tubing Slotted Collet Size Collet land Collar / 4 " / 8 " H H6 / 6 " H High Equipment Company R2 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 4.

44 High Equipment High Tubing Tubing is cold drawn, seamless, and is supplied in the hard condition (not annealed). Tensile strength is approximately 40 percent higher than that of annealed tubing. ll tubing is manufactured in strict accordance with High Equipment Company specifications to insure tolerances and bore quality. Tubing is stocked in lengths of 8 to 22 feet but may be ordered in shorter lengths with no additional cutting charge. Note: The O.D. tubing sizes may be coiled for shipment. Larger sizes must be shipped in straight lengths. /8 " /4 " /8 " /6 " /6 " " Working Type of Catalog Tubing Size psi Connection Used Material Order Number O.D. x 0.020" I.D. 60,000 HIH PRESSURE (HF2) 6 SS 60-H2 O.D. x 0.040" I.D. 0,000 HIH PRESSURE (HF2) 6 SS 0-H2 O.D. x 0.08" I.D. 60,000 HIH PRESSURE (HF4) 6 SS * 60-H SS * 60-H4-04 O.D. x I.D. 60,000 HIH PRESSURE (HF6) 6 SS 60-H SS 60-H6-04 /6" O.D. x /6" I.D. 60,000 /6" HIH PRESSURE (HF) 6 SS 60-H-6 04 SS 60-H-04 /6" O.D. x I.D. 40,000 /6" HIH PRESSURE (HF) 6 SS 40-H-6 04 SS 40-H-04 " O.D. x 0.4" I.D. 0,000 " HIH PRESSURE (HF6) 6 SS 0-H6-6 Nipples Nipples as shown below are stocked in Types 04 and 6 Stainless Steel. Nipples in lengths other than those shown are supplied upon request. Nipples are not furnished with collars and glands, unless specified at time of order. Coned and Threaded Nipples Length Tubing Size (O.D. x I.D.) x 0.020" x 0.040" ** x 0.08" x * /6" x * /6" x /6" * " x 0.4" ** psi 60,000 psi 0,000 psi 60,000 psi 60,000 psi 40,000 psi 60,000 psi 0,000 psi 60-HM2-2 0-HM HM4-2.5 " 60-HM2-0-HM2-60-HM6-4" 60-HM2-4 0-HM HM-4 60-HM-4 6" 60-HM2-6 0-HM HM HM HM-6 60-HM-6 0-HM6-6 8" 60-HM HM HM-8 60-HM-8 0-HM6-8 " 60-HM2-0-HM2-0" 60-HM HM HM-0 60-HM-0 0-HM HM2-2 0-HM HM HM HM-2 60-HM-2 0-HM6-2 Specify 6 SS or 04 SS when ordering. * lso used for 0,000 psi series. ** 6 SS 4.2 R4 /06

45 High Connections (Coned and Threaded) 0,000/40,000/60,000 psi service The High tubing connection is available for,,, /6" and " O.D. tubing. The tubing may be prepared with the use of tooling (see tooling section.0) or prepared at the factory to specified lengths. dditionally, standard length coned and threaded tubing nipples are available from stock (see page 4.2). This connection has become an industry standard for use at elevated pressures and temperatures in both liquid and gas applications. It may be disassembled and retightened indefinitely. The threads of the gland are right-hand while the threads of the collar and tubing are left-hand to prevent rotation of the collar during assembly. Materials ll of the components required for make-up of a High connection (glands, collars and plugs) are produced in Type 6 stainless steel. lands and collars are provided with all valves and fittings (except nipples) unless otherwise requested. (See chart on the right for size details and catalog numbers). HF2 HF4 /8 " O.D. Tubing /4 " O.D. Tubing Female Opening Detail land -20 IN. 60 #56 Drill.046 0,000 & 60,000 psi 40,000 psi 0,000 psi /6"-8 60 /6" /6" HF6 /8 " O.D. Tubing /6" 5/6" 5 HF /6 " O.D. Tubing -2 HF2 HF4 HF6 HF HF HF6 HEX 5 /6" 5 HEX /6" /6" HEX 5/6" 60 /6" /6" 5 HF /6 " O.D. Tubing /6" /6" 5 HF6 " O.D. Tubing -2 THD. 60 -HEX /6" 5 /6" HF2, HF4, HF6, HF 60-2HM2 60-2HM4 60-2HM6 60-2HM 60-2HM 0-2HM6 Collar Plug 5/6" -40 L.H L.H. -24-L.H. 5 /6"-8-L.H. 60-2H2 60-2H4 60-2H6 60-2H 60-2H 0-2H6 /6" /6" /6" /6" 5 /6"-8-L.H. "-4-L.H. Tubing land Collar /6" /6" /6" /6" 60-HM2 60-HM4 60-HM6 60-HM 40-HM 0-HM6 HF6 Tube End Prep 5 /6" -28-L.H. 5 /6" -24-L.H. 5 /6"-8-L.H. 5 /6" 5/6" /6"-8-L.H. 5 /6" 5/6" "-4-L.H Tubing land Collar /6" 5 /6" HM2 HM4 HM6 HM HM HM6 /6" High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 4. ppendix

46 High Equipment Ultra High Valves, Fittings and Tubing 00,000 and 50,000 psi service High Equipment Company has developed a line of Ultra High products to assure safe and easy plumbing for 00,000 psi and 50,000 psi. These needle valves, fittings, check valves, tubing and nipples are engineered to the highest standards of repeatable quality. The reliable performance of these products has made HiP one of the world s leading suppliers of elevated pressure components. Ultra High components use a coned-and-threaded connection which accommodates the extreme conditions found in these applications. Ultra High valves are available in and O.D. tubing sizes and four patterns to satisfy widely varied requirements. line of fittings is available to facilitate adapting to High systems. Index Page 00,000 psi Valves ,000 psi Valves Fittings Check Valves Tubing Coned and Threaded Nipples Connection Details ppendix 5.

47 High Equipment Ultra High Valves 00,000 psi service High (coned and threaded) type connections for O.D. by /6" I.D. tubing. Non-rotating tip stems insure long life on valve seats. Heavy duty rolled style stem design is shown below. lands and collars for tubing are supplied with each valve unless otherwise requested (glands and collars are shown on page 5.). Materials include 6 stainless steel for valve bodies with tool steel lower section stems. Valve packing is teflon. Corresponding fittings (elbows, tees, crosses, etc.) are shown on page 5.4. Replaceable Seat Valves are available for O.D. tubing. These valves feature the same body style and body dimensions as the two way angle valves (shown below). To order add R to the corresponding two way valve catalog number (eg. 00-2XF4R). K K K K D L J H D L J H D L J H D L J H F F E E F E E Two Way Straight Two Way ngle Three Way Two Inlets Three Way One Inlet Manual Shutoff Valves ody Pattern Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness 2-Way Straight 2-Way ngle -Way/2 Inlets -Way/ Inlet O.D. O.D. O.D. O.D. 00-XF4 00-2XF4 00-XF4 00-4XF4 00,000 00,000 00,000 00,000 XF4 XF4 XF4 XF4 /6" /6" /6" /6" 5" /6" 5 /6" /6" 5 /6" 5 /6" 2 2 "

48 Ultra High Valves 50,000 psi service High (coned and threaded) type connections for O.D. by /6" I.D. tubing. Non-rotating tip stems insure long life on valve seats. Heavy duty rolled style stem design is shown below. lands and collars for tubing are supplied with each valve unless otherwise requested (glands and collars are shown on page 5.). Materials include -4 PH for valve bodies with tool steel lower section stems. Valve packing is teflon. Corresponding fittings (elbows, tees, crosses, etc.) are shown on page 5.4. Replaceable Seat Valves are available for O.D. tubing. These valves feature the same body style and dimensions as the two way valves (shown below). To order add R to the corresponding two way valve catalog number (eg. 50-2XF6R). K K K K D L J H D L J H D L J H D L J H F F E E F E E Two Way Straight Two Way ngle Three Way Two Inlets Three Way One Inlet Manual Shutoff Valves ody Pattern Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness 2-Way Straight 2-Way ngle -Way/2 Inlets -Way/ Inlet O.D. O.D. O.D. O.D. 50-XF6 50-2XF6 50-XF6 50-4XF6 50,000 50,000 50,000 50,000 XF6 XF6 XF6 XF6 /6" /6" /6" /6" 5" /6" 2 /6" 2 /6" 2 /6" 2 /6" High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 5.

49 High Equipment Fittings/Check Valves We have developed check valves, elbows, tees and crosses for both the 00,000 and 50,000 psi systems. *Material is high tensile 6 stainless steel. Standard tubing glands and collars are furnished unless otherwise specified. * Note: Material for 50,000 psi check valve is -4 PH. Ultra High Check Valves Catalog No. psi Connections Length Hex 00-4XF4 00,000 ULTR PRESSURE /6" 50-4XF6 50,000 ULTR PRESSURE 4 E H F Ultra High Elbows Catalog No. psi Connections --C-D E F H Thickness 00-22XF4 00,000 O.D. TUE XF4 " 50-22XF6 50,000 O.D. TUE XF E H Ultra High Tees Catalog No. psi Connections --C-D E F H Thickness C F 00-2XF4 00,000 O.D. TUE XF4 2 " 50-2XF6 50,000 O.D. TUE XF6 2 5 C E D H F Ultra High Crosses Catalog No. psi Connections --C-D E F H Thickness 00-24XF4 00,000 O.D. TUE XF4 2 2 " 50-24XF6 50,000 O.D. TUE XF6 5.4

50 Ultra High Tubing Tubing is cold drawn, seamless, and is supplied in the /8 hard condition (not annealed). Tensile strength is approximately 40 percent higher than that of annealed tubing. ll tubing is manufactured in strict accordance with High Equipment Company specifications to insure tolerances and bore quality. Tubing is stocked in lengths of 8 to 22 feet but may be ordered in shorter lengths with no additional cutting charge. / 4 " / 8 " Working Type of Catalog Tubing Size psi Connection Used Material Order Number O.D. x /6" I.D. 00,000 ULTR HIH PRESSURE (XF4) 6 SS 00-X SS 00-X4-04 O.D. x /6" I.D. 50,000 ULTR HIH PRESSURE (XF6) 04 SS 50-X6 Nipples Nipples in lengths other than those shown are supplied upon request. Nipples are not furnished with collars and glands, unless specified at time of order. Coned and Threaded Nipples Length psi 2 4" 6" 8" 0" Tubing Size (O.D. x I.D.) O.D. x /6" I.D. (6 SS) (04 SS) 00,000 psi 00-XM XM XM XM XM4-2 00,000 psi 00-XM XM XM XM XM4-2 O.D. x /6" I.D. (04 SS) 50,000 psi 50-XM XM XM XM XM6-2 High Equipment Company R 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 5.5

51 High Equipment Ultra High Connections (Coned and Threaded) 00,000 and 50,000 psi service The Ultra High tubing connection is available for and O.D. tubing. The tubing may be prepared with the use of tooling (see tooling section.0) or prepared at the factory to specified lengths. dditionally, standard length coned and threaded nipples are available from stock, see page 5.5. This connection has become an industry standard for use at elevated pressures and temperatures in both liquid and gas applications. It may be disassembled and retightened indefinitely. The threads of the gland are right-hand while the threads of the collar and tubing are left-hand to prevent rotation of the collar during assembly. Materials. ll of the components required for make-up of a Ultra High connection (glands, collars and plugs) are produced in Type 6 stainless steel. Necessary glands and collars are provided with all valves and fittings (except nipples) unless otherwise requested (see chart on the right for size details and catalog numbers). XF4 Female Opening Detail XF4 land /4 " 5 /64" /6" - 8 THD 00-2XM4 Collar Plug 00-2X4 00,000 psi 50,000 psi XF4 XF6 /4 " O.D. Tubing /8 " O.D. Tubing /4 " - 6 /6 " - 8 /8 " 60 /8 " /6 " /2 " - -/8 " /6 " /4 " -28-L.H. XF6 60 /6 " /2 " - 6 TH'D. 50-2XM6 50-2X6 /8 " /8 " -24 TH'D. L.H. /6 " 5 - /2 " -/4 " - /8 " Tubing land Collar XF6 00-XM4 Tube End Prep /8 " /4 " O.D. x /6 " I.D. Tubing /4 "-28-L.H. 5 /6 " 50-XM6 /8 "-24 TH'D. L.H. /8 " O.D. x /6 " I.D. Tubing 5 /6 " Tubing land Collar XM4 /8 " XM6 /8 " 5. ppendix R4 2/02

52 High Equipment Specialty Valves High Equipment Company produces many valves engineered for specific requirements and operating conditions. all Valves provide shut-off of liquid or gas flow through 20,000 psi. These valves are available in two way and three way configurations. Hastelloy Valves are the most common special material valves we produce. We maintain an inventory of Hastelloy C-26 to assure prompt delivery. High Temperature Valves feature an extension to remove the packing area (stuffing box) from the hot zone of a valve, making them suitable for use at,000 F (58 C). Micro Control Metering Valves are designed to assure the fine and precise stem travel necessary for excellent control of flow. n integral vernier indicator provides exact measurement of stem revolution. Relief Valves protect a system from over-pressure damage and failure. Relief Valves are offered in pressure ranges:,000 psi to 0,000 psi. Male ottom Connection Valves are designed for applications where extra rigidity or space restrictions are critical. These valves feature one-piece stem construction to increase durability and reduce overall height. lock and leed Valves These two stem manifold valves are an excellent method of blocking, bleeding and calibrating pressure gauges and transmitters. Subsea all Valves Designed for extreme pressures and harsh environments, the industry s broadest line of subsea ball valves for 0, 5 and 20,000 psi. Index Page all Valves Hastelloy Valves High Temperature Valves Metering Valves Relief Valves Male ottom Connection Valves...6. lock and leed Valves Subsea all Valves R6 5/ 6.

53 High Equipment all Valves 0,000, 5,000 and 20,000 psi service High Equipment offers two styles of ball valves (free floating and trunion) to provide effective shut-off of liquid or gas flow. Two-way ball valves offer complete shut-off with a convenient /4 turn. Valve actuators are available for remote control of HiP ball valves. Virtually all metal components are stainless steel to insure consistent operation under even the most severe applications. Teflon packing provides reliable leak-free service up to 400 F. Other packings, including Polypak and rafoil are available upon request. Two-Way Free Floating all Valves Catalog No. Tube Size Minimum Orifice C v 5-6F 5-6F2 0-6F4 0-6F6 /6" F F2 F4 F6 5,000 psi 5,000 psi 0,000 psi 0,000 psi LF4 LF4 20,000 psi LF6 20-6LF /6" LF6 LF 20,000 psi 20,000 psi /6" 20-6HF2 20-6HF4 20-6HF6 20-6HF /6" HF2 HF4 HF6 HF 20,000 psi 20,000 psi 20,000 psi 20,000 psi NF NPT 0,000 psi NF NPT 0,000 psi NFC NPT 0,000 psi NFD NPT 0,000 psi * Other connections available upon request. Consult factory. 6.2 R5 8/04

54 Severe Duty all Valves (Trunion Style) 0,000, 5,000 and 20,000 psi service High Equipment Company introduces its TRUNION STYLE ball valves for effective shut-off of liquid and gas flow through 20, F maximum. Our offering features a trunion ball design, making this type of valve ideal for severe duty applications. This valve is available in two-way or three-way configurations with orifices of.8",.5" or.500". The two-way ball valve offers complete shut-off with a convenient /4 turn. The standard configuration of the three-way ball valve requires /2 turn to change port outlets and provides for complete shut-off. n optional diverter style three-way ball valve requires only a /4 turn to change the port outlets. ir operated actuators are available for remote control. Material of construction is 6 stainless steel, O-rings are Viton, ball seat is PEEK. lternate materials of construction are available upon request. Trunion style closure, ideal for severe duty applications Two-way and three-way valve configurations Three-way, /4 turn diverter valve.8",.5" or.500" orifices ir actuators for remote operation Convenient panel mount design (cut /6" diameter hole).8 and.5 only Large selection of tube and pipe fittings available Optional wetted parts available Optional O-rings available Two-Way Trunion all Valves - 0 Orifice.8.5 Tube Size Connection Minimum Orifice /6" F F2 5,000 psi 5,000 psi F4 0,000 psi.25 F6 0,000 psi.8 LF4 20,000 psi.0 LF6 20,000 psi.8 /6" LF 20,000 psi.8 HF4 20,000 psi.04 HF6 20,000 psi.25 /6" HF 20,000 psi.8 NPT 5,000 psi.8 NPT 5,000 psi.8 NPT 5,000 psi.8 /6" " F6 LF LF2 LF6 NPT NPT NPT 0,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi Cv Catalog No. 5-F 5-F2 0-F4 0-F6 20-LF4 20-LF6 20-LF 20-HF4 20-HF6 20-HF 5-NF 5-NF 5-NFC 0-4F6 5-4LF 5-4LF2 5-4LF6 5-4NF 5-4NFC 5-4NFD diam. 6. mtg. holes Dimensions in inches..8 Orifice Dimensions in inches Orifice panel cutout /6" 0.8 diam. mtg. holes panel cutout /6".00 diam. mtg. holes " " LF2 LF6 NPT " NPT 0,000 psi 0,000 psi 0,000 psi 0,000 psi LF2 0-80LF6 0-80NFF 0-80NFH Dimensions in inches..500 Orifice High Equipment Company R 5/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 6.

55 Three-Way Trunion all Valves panel cutout /6" panel cutout /6".00 diam. 6. mtg. holes thick block Dimensions in inches..8 Orifice diam. mtg. holes thick block Dimensions in inches..5 Orifice diam. mtg. holes Dimensions in inches..500 Orifice.8 Open Closed Open Open Open 80 Three-Way all Valve 0 Three-Way Diverter Valve Orifice.8 Tube Size Connection Minimum Orifice /6" /6" /6" F F2 F4 F6 LF4 LF6 LF HF4 HF6 HF NPT NPT NPT 5,000 psi 5,000 psi 0,000 psi 0,000 psi 20,000 psi 20,000 psi 20,000 psi 20,000 psi 20,000 psi 20,000 psi 5,000 psi 5,000 psi 5,000 psi Cv Way 0 Catalog No. 5-F 5-F2 0-F4 0-F6 20-LF4 20-LF6 20-LF 20-HF4 20-HF6 20-HF 5-NF 5-NF 5-NFC -Way 80 Catalog No. 5-2F 5-2F2 0-2F4 0-2F6 20-2LF4 20-2LF6 20-2LF 20-2HF4 20-2HF6 20-2HF 5-2NF 5-2NF 5-2NFC.5 F6 /6" LF LF2 " LF6 NPT NPT NPT 0,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi F6 5-6LF 5-6LF2 5-6LF6 5-6NF 5-6NFC 5-6NFD 0-5F6 5-5LF 5-5LF2 5-5LF6 5-5NF 5-5NFC 5-5NFD.500 " LF2 LF6 NPT " " NPT 0,000 psi 0,000 psi 0,000 psi 0,000 psi LF2 0-82LF6 0-82NFF 0-82NFH 0-8LF2 0-8LF6 0-8NFF 0-8NFH 6.4 R6 0/04

56 all Valve ctuators High Equipment Company offers air operated actuators to accommodate remote operation. NOTE: These air operators are only for use with two-way and three-way diverter style valves. To order: simply specify the appropriate ball valve catalog number and add the suffix -TSR8 for air to open/spring to close, or -TD8 for air to open and close (double acting) or TSR20 for orifice. For trunion only. Use TD4 and TSR4 for floating ball style valves diam. mtg. holes * diam. mtg. holes thick.50 block 2.6 * Dimensions in inches. * Dimensions found within charts on pages Orifice.8 diam * mtg. holes thick 2.00 block.6 * Dimensions in inches. * Dimensions found within charts on pages Orifice * thick 2.50 block 4.2 * Dimensions in inches. * Dimensions found within charts on pages Orifice.8 High Equipment Company R6 0/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 6.5

57 High Equipment Hastelloy Valves large number of the valves and fittings shown within this catalog are frequently furnished in special materials to meet the requirements of specific applications. One of the most commonly requested special materials is Hastelloy C-26. While very few components are maintained in stock in special materials, a supply of Hastelloy C-26 is normally available. The following should be observed when requesting items in Hastelloy C-26 or other special materials: Tubing collars and glands for High coned-andthreaded connections are non-wetted parts which do not normally come into contact with the fluid or gas. Thus these items are supplied in 6 stainless steel unless otherwise specified. The inner sleeve connection of the Taper Seal is a wetted part and must be of the same material as the valve or fitting body. The Taper Seal gland is a non-wetted part and is supplied in 6 stainless steel unless otherwise requested. Physical size of Hastelloy C-26 or other special material items may vary from the dimensions of standard items shown in this catalog, depending on availability of materials. (Parts normally supplied in hex shaped material are frequently supplied in round shaped material with wrench flats when manufacturing from special materials). Packing material in all special material valves is Teflon unless otherwise specified. Other materials. In addition to Hastelloy C-26, valves and fittings can be furnished in Monel, Inconel, titanium and various other special materials. Consult factory for price and delivery. High Temperature Valves The High Temperature Extension provides a means to move the packing area (stuffing box) away from the hot zone of a valve. Fins are provided around the packing area to dissipate heat and, with proper cooling of the extension, these valves can be used at,000 F (58 C). Size range. High temperature extensions are available for O.D., O.D., and /6" O.D. tubing size valves in the 0,000 psi series and for all Medium series valves. Materials and features. Standard packing is rafoil. Teflon packing is also available. Nonrotating tip stems prevent galling at the seats and minimize torque requirements for positive shut off. When ordering, simply add the suffix -HT to the standard valve catalog number (example: 0-HF4-HT). Note: These valves may also be used in cryogenic applications. Teflon packing supplied. 6.6 R4 2/02

58 Micro Control Metering Valves The Micro Control Metering Valve assembly is available for all of the valves in the 60,000 psi series. This unique stem design operates on the principle of a right-hand threaded component operating in an opposite direction of motion to a left-hand threaded component. s the pitch sizes of these threads are different from each other, a very fine and precise stem travel is made possible. This provides exceptional control that is not possible with ordinary fine pitched stem designs. Each complete revolution of the stem provides 0.005" stem travel. The vernier indicator allows readings in increments of one-tenth of a revolution (0.0005" stem travel). The non-rotating lower section stem is ground to a degree included angle to insure maximum control. While this valve may be turned to the fully off (closed) position, it is always preferable to provide a separate on-off valve in the system to protect the precise control of the metering valve. When ordering, simply specify the valve catalog number from the 60,000 psi series and add the suffix -V (example: 60-HF4-V.) Square section prevents stem tip rotation. Metering Tip Valves When the precision control offered by the above Micro Control metering valve is not required, a multi-piece, rolled fine pitched stem assembly can be provided. The non-rotating lower section stem is ground to a degree included angle and provides a.050" stem travel per complete revolution of the handle. While this valve may be turned to the fully off (closed) position, it is always preferable to provide a separate on-off valve in the system to protect the precise control of the metering valve. When ordering, simply specify valve catalog number from the 60,000 psi series and add the suffix -MTS (example: 60-HF4-MTS). For pricing consult factory. High Equipment Company R5 8/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 6.

59 High Equipment Relief Valves (Factory Set) Relief valves are offered in pressure ranges:,500 through 60,000 psi. Standard materials include 6 stainless steel bodies and removable seat glands with -4PH stainless steel removable seats and pistons. Standard O-ring material on the piston is Viton Valves may be used up to 50 F. Inlet connections are for /6" O.D. tubing (HF) with adapters for other sizes available. Outlet connections are NPT. These valves are not recommended for use below,500 psi, and are not readily adjustable in the field without proper test equipment. settings are made at the factory and valves are tagged accordingly. To order, simply specify catalog number and set pressure. See table below. " Outlet Connection ( /2 " NPT) Range Orifice Type of Service* ssembly Max Flow Capacity Size Part No. H 2 O (PM),500 to 2, psi S OR LIQUID ,000 to 0, psi S OR LIQUID ,000 to 20, psi /6" S OR LIQUID ,000 to 0,000 psi S OR LIQUID ,00 to 45,000 psi /64" S OR LIQUID ,00 to 60,000 psi S OR LIQUID *Valves not bubble tight on gas service. Orifice 2 /2 " Inlet Connection (HF) 2 /8 " Relief Valves (Field djustable) Relief valves are offered in pressure ranges:,000 through 20,000 psi. Standard materials include 6 stainless steel bodies and seat glands. Standard O-ring material is EPDM, with teflon packing and nylon seats. Inlet connections NPT-HIP-0RV; HF4-HIP-20RV. Outlet connections are NPT. These valves are not recommended for use below,000 psi, and are readily adjustable in the field. To order, simply specify catalog number. Example: HIP-0RV 5 /2 " /4 " 6.25".55 Range Orifice Size Type of Service Part number Cv,000 to 0,000 psi 0.00 S OR LIQUID HIP-0RV.2 0,00-20,000 psi 0.00 S OR LIQUID HIP-20RV.2 /6 " /2 " HIP-0-RV HIP-20-RV *Please note HIP-20RV does not have handle, the valve is shipped with /2-" set screw. 6.8 R6 8/04

60 Male ottom Connection Valves Connections. This series of valves is offered in a few select variations which are most frequently required. They have been developed for applications where rigidity is a major concern (such as gas bottles) and where space is restricted. Pipe connections as well as High (coned and threaded) connections are available as listed in tables below. dditionally, these valves can be supplied with rupture disc assemblies (safety heads) installed directly into the valve body as shown (see page. for listing of rupture discs). Stems. The Male ottom Connection Valves are supplied with a one-piece (solid construction) stem to maximize sensitivity of feel and to reduce overall height. The non-rotating tip stem design as featured on other valves may be supplied as an option at no additional charge. Materials include high tensile Type 6 stainless steel valve bodies and hardened -4PH stainless steel stems. Packing is Teflon (450 F) standard with optional Viton (50 F), UN-N (200 F) and rafoil (650 F) available at no additional cost. ir operators for remote control operation are available for all valves. (Select required valve and add HIPCO ). Rupture discs must be ordered separately (see section.). Special valves with connections other than those listed can be manufactured on special order when quantity permits. Consult factory with specifications. Without Safety Head With Safety Head K Male ottom Connection Valves (without Safety Head) D H E J L ssembly Number Male ottom NPT NPT NPT NPT Female Side NPT HF4 NPT HF4 psi Orifice D E H J K L Thickness 0,000 0,000 0,000 0,000 5 /6" 5 /6" 5 /6" 5 /6" 5 /6" 5 /6" 5 /6" 5 /6" " " " " K Male ottom Connection Valves (with Safety Head) D H E J L ssembly Number Male ottom NPT NPT NPT NPT Female Side NPT HF4 NPT HF4 * Rupture discs must be ordered separately (see section.). psi Orifice D E H J K L Thickness 0,000 0,000 0,000 0,000 5 /6" 5 /6" /6" 5 /6" 2 2 /6" /6" " " " " High Equipment Company R6 8/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 6.

61 High Equipment lock and leed Needle Valves High Equipment offers lock and leed needle valves designed for calibration operations. lock and leed needle valves provide controlled flow to high-pressure hydraulic and pneumatic systems through both shut-off regulation and diversion. These needle valves deliver safe, reliable operation to 20,000 psi.* Teflon packing provides dependable leak-free service up to 400 F (204 C). Tube sizes:,, /6" medium pressure and FNPT, FNPT, FNPT Non-rotating stem design Type 00 stainless steel tee handles Teflon packing to 400 F (204 C) Optional wetted parts available Optional O-rings available - MT Holes -5 D Catalog Number Connector C D E F leed 2- C Inlet 5-S-NF 5-S-NFC 5-S-NFD 20-S-LF4 20-S-LF6 20-S-LF NPT NPT NPT LF4 LF6 LF 2 5 " " /6" 5 /6" 5 /6" 5 /6" /6" /6" /6" /6" /6" /6" " /6" 5 /6" E F - * NPT connection: rated 5,000 psi Dimensions in inches 6.0 R 5/

62 Double lock and leed Needle Valves High Equipment Company introduces its Double lock and leed needle valves that deliver safe, reliable operation to 20,000 psi. Our valves feature coned and threaded connections for to " medium pressure tubing, making them ideal for pressure monitoring and testing, chemical injection and drain line isolation applications. This valve is manufactured from cold worked stainless steel and -4-H05 with 00 stainless steel tee handles and a non-rotating stem design. Teflon packing provides reliable leak-free service from 0 F (-.8 C) to 400 F (204 C). Rated for service to 20,000 psi D series: to " medium pressure, coned and threaded connections Non-rotating stem design Type 00 stainless steel tee handles Manufactured from cold worked stainless steel and -4-H05 FNPT vent Teflon packing from 0 F (-.8 C) to 400 F (204 C) Optional wetted parts available Optional PolyPak available Vent Connection /4 NPT H pproximate E.85" F Outlet Connection Catalog Number 20-D-LF4 20-D-LF6 20-D-LF 20-D-LF2 20-D-LF6 Inlet Connector LF4 LF6 LF LF2 LF6 Outlet Connector LF4 LF6 LF LF2 LF6 C D E F 2 2 /6" /6" 2 2 /6" /6" 4 6 /6" " 6 2 /6" 5 2 /6" " 8 /6" H /6" /6" " " K " " K pproximate C D " Dimensions in inches Inlet Connection High Equipment Company /0 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 6.

63 High Equipment Subsea all Valves In today s offshore oil and gas industry, wells have become deeper than ever, causing a growing demand for subsea ball valves that can withstand extreme pressures and harshest environments. s a leader in developing ways to provide effective shut off under increasing temperature and pressure requirements at greater depths, High Equipment offers subsea ball valves that provide safe and reliable operation at very high external pressures. High Equipment s Subsea all Valves feature their reliable trunion style ball design and incorporate the required design modifications for ideal performance in critical subsea systems. HiP offers the industry s widest range of subsea valve sizes, these valves are available in 2 or way configurations with 80 operation or 0 diverter styles in.8",.5" and.500" orifices and 0, 5 and 20,000 psi pressure ranges. Subsea Valve Features Trunion style ball design 6 cold-worked SS construction Two and three-way valve configurations 0 diverter or 80 styles.8",.5" and.500" orifices PEEK ball seats, which offers excellent resistance to chemicals, heat and wear/abrasion Optional O-rings available Optional wetted materials vailable to NCE MR /

64 Subsea all Valves.8 Orifice Subsea all Valves flat flat Dimensions in inches. -Way all Valve Dimensions in inches. 2-Way all Valve Orifice -Way 80 -Way 0 Diverter 2-Way Tube Size Connection Minimum Orifice HF6 20,000 psi 0.25 HF4 20,000 psi 0.04 /6" LF 20,000 psi 0.8 LF6 20,000 psi 0.8 LF4 20,000 psi 0.0 NPT 5,000 psi 0.8 NPT 5,000 psi 0.8 HF6 20,000 psi 0.25 HF4 20,000 psi 0.04 /6" LF 20,000 psi 0.8 /6" /6" LF6 LF4 NPT NPT HF HF6 HF4 LF LF6 LF4 NPT NPT NPT NPT 20,000 psi ,000 psi 0.0 5,000 psi 0.8 5,000 psi ,000 psi ,000 psi 20,000 psi 20,000 psi 20,000 psi 20,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi Cv Catalog No. 20-2HF6-SU 20-2HF4-SU 20-2HF-SU 20-2LF6-SU 20-2LF4-SU 5-2NFC-SU 5-2NF-SU 20-HF6-SU 20-HF4-SU 20-LF-SU 20-LF6-SU 20-LF4-SU 5-NFC-SU 5-NF-SU 20-HF-SU 20-HF6-SU 20-HF4-SU 20-LF-SU 20-LF6-SU 20-LF4-SU 5-NFD-SU 5-NFC-SU 5-NF-SU 5-NF-SU High Equipment Company / 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 6.

65 .5 Orifice Subsea all Valves square Square Dimensions in inches. -Way all Valve. 5.5 Dimensions in inches. 2-Way all Valve Orifice -Way 80 -Way 0 Diverter 2-Way Tube Size Connection Minimum Orifice LF2 5,000 psi 0.5 /6" LF 5,000 psi 0.2 LF6 5,000 psi 0.20 NPT 5,000 psi 0.5 NPT 5,000 psi 0.5 NPT 5,000 psi LF2 5,000 psi 0.5 /6" LF 5,000 psi 0.2 LF6 5,000 psi 0.20 NPT 5,000 psi 0.5 /6" NPT NPT LF2 LF LF6 NPT NPT NPT 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi 5,000 psi Cv Catalog No. 5-5LF2-SU 5-5LF-SU 5-5LF6-SU 5-5NFD-SU 5-5NFC-SU 5-5NF-SU 5-6LF2-SU 5-6LF-SU 5-6LF6-SU 5-6NFD-SU 5-6NFC-SU 5-6NF-SU 5-4LF2-SU 5-4LF-SU 5-4LF6-SU 5-4NFD-SU 5-4NFC-SU 5-4NF-SU 6.4 /

66 .500 Orifice Subsea all Valves flats square Dimensions in inches. -Way all Valve 4.2. Dimensions in inches. 2-Way all Valve Orifice -Way 80 -Way 0 Diverter 2-Way Tube Size Connection Minimum Orifice " " " " " " " NPT NPT LF6 LF2 " NPT NPT LF6 LF2 " NPT NPT LF6 LF2 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi Cv Catalog No. 0-8NFH-SU 0-8NFF-SU 0-8LF6-SU 0-8LF2-SU 0-82NFH-SU 0-82NFF-SU 0-82LF6-SU 0-82LF2-SU 0-80NFH-SU 0-80NFF-SU 0-80LF6-SU 0-80LF2-SU Open Closed Open 80 Three-Way all Valve Open Open Open Closed 0 Three-Way Diverter Valve Two-Way Valve High Equipment Company / 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 6.5

67 High Equipment ir Operated Valves High Equipment Company offers five lines of air operators to accommodate remote operation of pressure valves up to 00,000 psi. Various models of diaphragm and piston operated valves are available in both normally open and normally closed models, and can be controlled by air regulator, electrical solenoid or low pressure manual valve. The Remetco line of air operated metering valves provides remote operation for fine metering applications. Index Page Mini-Hippo Piston ir Operators Hipco Diaphragm ir Operators Remarco Diaphragm ir Operators Hippo Piston ir Operators Remetco Piston ir Operated Fine Metering Valves R2 2/.

68 High Equipment Mini-Hippo Piston ir Operators for Remote Operation To 6,000 psi Mini-Hippo ir Operators are available for both normally open service (spring to open/air to close) and for normally closed service (air to open/spring to close). These piston air operators provide remote automatic on/off operation of valves and can be controlled by means of an air regulator, an electrical solenoid, or a manual low pressure valve in the user s air supply line. ir inlet is NPT. ir pressure requirement ranges from 50 to 0 psi. The Mini-Hippo air operators may be supplied with the valves and operating pressures shown in table. To order simply specify catalog number of valve and type operation required. EXMPLES: Mini-Hippo 0-HF4 (normally closed) Mini-Hippo 0-2F6 (normally open) Mini-Hippo 0-5F4 (normally open/ normally closed) " Diameter Piston ir Operators Normally Open (Spring To Open / ir To Close) Valve Maximum Operating pproximate Ir Series to Seat Valve 0-**F2 6,000 psi 55 psi 0-**F4 6,000 psi 55 psi 0-**F6 6,000 psi 55 psi 0-**HF4 6,000 psi 55 psi 0-**HF6 6,000 psi 55 psi 0-**HF 6,000 psi 55 psi Normally Closed (ir To Open / Spring To Close) Minimum pproximate pproximate Valve Maximum djusting ir ir Series Operating Screw to Unseat to Fully Torque Valve Open Valve 0-**F4 6,000 psi 5 in. lb. 50 psi 0 psi 0-**F6 6,000 psi 5 in. lb. 50 psi 0 psi 0-**HF4 6,000 psi 5 in. lb. 50 psi 0 psi 0-**HF6 6,000 psi 5 in. lb. 50 psi 0 psi 0-**HF 6,000 psi 5 in. lb. 50 psi 0 psi ** Standard Valve Patterns (reference Page.4) OPTIONS: Stems & Seats.... Carbide (for cyclic service) Stellite (for cyclic service) (for cyclic service) Valve odies..... Hastelloy C, Hastelloy Inconel 600, Inconel Incoloy 800, Incoloy Titanium rade 2, Titanium 6L4V Nickel Monel Packing PolyPak Temperature Considerations.... Extended stuffing box for temperatures from -42 F to,200 F (medium and high pressure connections only) Normally Open Normally Closed..5 R4 2/02

69 Hipco Diaphragm ir Operators for Remote Operation To 60,000 psi Hipco ir Operators are available for both normally open service (spring to open/air to close) and for normally closed service (air to open/spring to close). These diaphragm air operators provide remote automatic on/off operation of valves and can be controlled by means of an air regulator, an electrical solenoid, or a manual low pressure valve in the user s air supply line. ir inlet is NPT. The Hipco air operators may be supplied with the valves and operating pressures shown in table. To order simply specify catalog number of valve and type operation required. EXMPLES: Hipco 0-HF4 (normally closed) Hipco 0-2NF (normally open) Hipco 0-5F4 (normally open/normally closed) OPTIONS: Stems & Seats.... Carbide (for cyclic service) Stellite (for cyclic service) (for cyclic service) Valve odies..... Hastelloy C, Hastelloy Inconel 600, Inconel Incoloy 800, Incoloy Titanium rade 2, Titanium 6L4V Nickel Monel Packing PolyPak Temperature Considerations.... Extended stuffing box for temperatures from -42 F to ,200 F (medium and high pressure connections only) Normally Open 6 Diameter Diaphragm ir Operators Normally Closed ir Operated Valves Normally Open (Spring To Open / ir To Close) Valve Maximum Operating pproximate Ir Series to Seat Valve 0-**F4 0,000 psi 5 psi 0-**F6 0,000 psi 5 psi 0-**NF 0,000 psi 5 psi 0-**NF 0,000 psi 5 psi 0-**NFC 0,000 psi 5 psi 5F-**NF 5,000 psi 85 psi 5F-**NF 5,000 psi 85 psi 5F-**NFC 0,000 psi 00 psi 5F-**NFD 0,000 psi 00 psi 20-**LF4 20,000 psi 60 psi 20-**LF6 5,000 psi 85 psi 20-**LF 0,000 psi 00 psi 0-**HF4 0,000 psi 60 psi 0-**HF6 0,000 psi 85 psi 0-**HF 0,000 psi 85 psi 40-**HF 0,000 psi 85 psi 60-**HF4 60,000 psi 0 psi 60-**HF6 60,000 psi 0 psi 60-**HF 60,000 psi 0 psi Normally Closed (ir To Open / Spring To Close) Valve Series Maximum Operating ** Standard Valve Patterns (reference Page.4) Minimum pproximate pproximate djusting ir ir Screw to Unseat to Fully Torque Valve Open Valve 0-**F4 0,000 psi 20 in. lb. 0 psi 45 psi 0-**F6 0,000 psi 20 in. lb. 0 psi 45 psi 0-**NF 0,000 psi 20 in. lb. 0 psi 45 psi 0-**NF 0,000 psi 20 in. lb. 0 psi 45 psi 0-**NFC 0,000 psi 20 in. lb. 0 psi 45 psi 5F-**NF 5,000 psi 60 in. lb. 80 psi 00 psi 5F-**NF 5,000 psi 60 in. lb. 80 psi 00 psi 5F-**NFC 0,000 psi 5 in. lb. 5 psi 00 psi 5F-**NFD 0,000 psi 5 in. lb. 5 psi 00 psi 20-**LF4 20,000 psi 40 in. lb. 55 psi 0 psi 20-**LF6 5,000 psi 60 in. lb. 80 psi 00 psi 20-**LF 0,000 psi 5 in. lb. 5 psi 00 psi 0-**HF4 0,000 psi 40 in. lb. 55 psi 5 psi 0-**HF6 0,000 psi 60 in. lb. 80 psi 00 psi 0-**HF 0,000 psi 60 in. lb. 80 psi 00 psi 40-**HF 0,000 psi 60 in. lb. 80 psi 00 psi 60-**HF4 60,000 psi 50 in. lb. 65 psi 85 psi 60-**HF6 60,000 psi 50 in. lb. 65 psi 85 psi 60-**HF 60,000 psi 50 in. lb. 65 psi 85 psi High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

70 High Equipment Remarco Diaphragm Operated Valves for Remote Operation To 00,000 psi Remarco air operated valves are available for both normally open service (spring to open/air to close) and for normally closed service (air to open/spring to close). These diaphragm operated valves provide remote operation up to 00,000 psi by means of an air input supply ranging from 25 to 0 psi to the air actuator. n electrical solenoid valve for the air supply is provided with all Remarco valves and is mounted directly to the valve. The standard solenoid is 20 volt, 60 cycle, watts with NPT air inlet. (Other voltages available at additional charge consult factory). The solenoid is normally closed and when energized allows air into the diaphragm casing to activate the valve. In the event of an electrical or air line failure, the valve will return to its normal position. The Remarco valve features removable stem seats. Valve bodies are 6 stainless steel. Valve stems are hardened -4PH stainless steel up to 60,000 psi. Tool steel stems are standard on 00,000 psi valves. Standard packing on the 0,000 psi and 60,000 psi Remarco valves is Teflon O-ring with una-n, Viton, or Silicone, available at no additional cost. Normally Open Diameter Diaphragm ir Operators Normally Closed Normally Open (Spring To Open / ir To Close) Valve Series D0R2LFR D20R2LFR D0R2HF4R D0R2HF6R D0R2HFR D0R2HFR D60R2HF4R D60R2HF6R D60R2HFR D00R2XF4R D00R2XF6R Maximum Operating 0,000 psi 20,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 60,000 psi 60,000 psi 60,000 psi 00,000 psi 00,000 psi 60 psi 5 psi 65 psi 65 psi 65 psi 60 psi 55 psi 55 psi 55 psi 0 psi 0 psi Normally Closed (ir To Open / Spring To Close) Valve Series SD0R2LFR SD20R2LFR SD0R2HF4R SD0R2HF6R SD0R2HFR SD0R2HFR SD60R2HF4R SD60R2HF6R SD60R2HFR SD00R2XF4R SD00R2XF6R 0,000 psi 20,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 60,000 psi 60,000 psi 60,000 psi 00,000 psi 00,000 psi 20 ft. lb. 40 ft. lb. 20 ft. lb. 20 ft. lb. 20 ft. lb. 20 ft. lb. 20 ft. lb. 20 ft. lb. 20 ft. lb. 0 ft. lb. 0 ft. lb. 55 psi 0 psi 60 psi 60 psi 60 psi 55 psi 50 psi 50 psi 50 psi 85 psi 85 psi 0 psi 0 psi 5 psi 5 psi 5 psi 0 psi 65 psi 65 psi 65 psi 00 psi 00 psi /6" /6" /6" /6" /6" /6" /6" /6" /6" /6" LF LF HF4 HF6 HF HF HF4 HF6 HF XF4 XF6 LF LF HF4 HF6 HF HF HF4 HF6 HF XF4 XF6 /6" /6" /6" /6" /6" /6" 5 /6" 5 /6".08" Tubing pproximate Connections Size ir Orifice to Seat Valve O.D. I.D. pproximate pproximate Tubing Maximum Lock Nut ir ir Size Operating Torque Connections to Unseat to Fully Orifice Setting Valve Open Valve O.D. I.D. /6" /6" /6" /6" 5 /6" 5 /6".08" /6" 5 /6" /6" OPTIONS: Stems & Seats.... Carbide (for cyclic service) Stellite (for cyclic service) Valve odies..... MP5N water service 00K valve Hastelloy C, Hastelloy Inconel 600, Inconel Incoloy 800, Incoloy Titanium rade 2, Titanium 6L4V Nickel, Monel Packing PolyPak Temperature Considerations.... Extended stuffing box for temperatures from -42 F to,200 F (medium and high pressure connections only) /6" 5 /6" /6" /6" /6" /6" /6" /6" /6". R5 5/

71 Hippo Piston ir Operators for Remote Operation To 60,000 psi Hippo Piston ir Operators are available for both normally open service (spring to open/air to close) and for normally closed service (air to open/spring to close). These piston air operators provide remote automatic on/off operation of valves and can be controlled by means of an air regulator, an electrical solenoid, or a manual low pressure valve in the user s air supply line. ir inlet is NPT. ir pressure requirement ranges from 5 psi to 20 psi. These operators may be supplied with the valves and operating pressures shown in table. Normally Closed (ir To Open / Spring To Close) Medium Duty Valve Series 0-**F4 0-**F6 5F-**NF 5F-**NF 5F-**NFC 5F-**NFD 20-**LF4 20-**LF6 20-**LF 0-**HF4 0-**HF6 0-**HF 60-**HF4 60-**HF6 60-**HF Heavy Duty Maximum Operating 0,000 psi 0,000 psi 5,000 psi 5,000 psi 0,000 psi 0,000 psi 20,000 psi 20,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 60,000 psi 60,000 psi 60,000 psi 5F-**NFC 5,000 psi 5F-**NFD 5,000 psi 20-**LF4 20,000 psi 20-**LF6 20,000 psi 20-**LF 6,000 psi 20-**LF2,000 psi 20-**LF6 6,000 psi 0-**HF4 0,000 psi 0-**HF6 0,000 psi 0-**HF 0,000 psi 60-**HF4 60,000 psi 60-**HF6 60,000 psi 60-**HF 60,000 psi Extra Heavy Duty 20-**LF2 20,000 psi 0-**NFF 0,000 psi 0-**NFH 0,000 psi 0-**LF6 0,000 psi 20-**LF6 20,000 psi 0-**LF6 0,000 psi Orifice Size /64" /64" 5/6" 5/6" /64" 5/6" /6" /6" /6" 5/6" 5/6" /64" 5/6" /6" /6" /6" /6" /6" /6" /6" /6" /6" /6" /6" Minimum djusting Screw Torque 25 in.lb. 25 in.lb. 45 in.lb. 45 in.lb. 55 in.lb. 55 in.lb. 50 in.lb. 55 in.lb. 55 in.lb. 50 in.lb. 55 in.lb. 55 in.lb. 50 in.lb. 50 in.lb. 50 in.lb. 85 in.lb. 85 in.lb. 55 in.lb. 60 in.lb. 85 in.lb. 85 in.lb. 85 in.lb. 50 in.lb. 55 in.lb. 55 in.lb. 50 in.lb. 50 in.lb. 50 in.lb. 60 ft.lb. 5 ft.lb. 5 ft.lb. 5 ft.lb. 5 ft.lb. 0 ft.lb. pproximate ir to Unseat Valve 0 psi 0 psi 55 psi 55 psi 0 psi 0 psi 0 psi 0 psi 0 psi 60 psi 60 psi 60 psi 50 psi 50 psi 50 psi 60 psi 60 psi 5 psi 5 psi 60 psi 60 psi 60 psi 0 psi 0 psi 0 psi 25 psi 25 psi 25 psi 5 psi 45 psi 45 psi 45 psi 55 psi 50 psi pproximate ir to Fully Open 40 psi 40 psi 5 psi 5 psi 5 psi 5 psi 5 psi 5 psi 5 psi 5 psi 5 psi 5 psi 65 psi 65 psi 65 psi 5 psi 5 psi 50 psi 50 psi 5 psi 5 psi 5 psi 40 psi 40 psi 40 psi 5 psi 5 psi 5 psi 60 psi 0 psi 0 psi 0 psi 5 psi 85 psi Part Number Suffix MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC MPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC HPO-NC EHPO-NC EHPO-NC EHPO-NC EHPO-NC EHPO-NC EHPO-NC ir Operated Valves To order simply specify catalog number of valve and appropriate suffix of operator required. EXMPLES:....Hippo 20-LF4-MPO-NC (normally closed) hippo 20-2LF6-HPO-NO (normally open) OPTIONS: Stems & Seat...Carbide, ceramic or Stellite (for cyclic service) Valve odies....hastelloy C, Hastelloy Inconel 600, Inconel Incoloy 800, Incoloy Titanium rade 2, Titanium 6L4V Nickel Monel Packing PolyPak Temperature.... Consideration...Extended stuffing box for temperatures from -42 F to,200 F (medium and high pressure connections only) Normally Open (Spring To Open / ir To Close) Medium Duty Maximum Valve Series Operating 0-**F4 0,000 psi 0-**F6 0,000 psi 5F-**NF 5,000 psi 5F-**NF 5,000 psi 5F-**NFC 0,000 psi 5F-**NFD 0,000 psi 20-**LF4 20,000 psi 20-**LF6 20,000 psi 20-**LF 0,000 psi 20-**LF2 6,000 psi 0-**HF4 0,000 psi 0-**HF6 0,000 psi 0-**HF 0,000 psi 60-**HF4 60,000 psi 60-**HF6 60,000 psi 60-**HF Heavy Duty 5F-**NFC 5F-**NFD 20-**LF4 20-**LF6 20-**LF 20-**LF2 20-**LF6 0-**HF4 0-**HF6 0-**HF 60-**HF4 60-**HF6 60-**HF 60,000 psi 8,800 psi 5,000 psi 5,000 psi 20,000 psi 20,000 psi 20,000 psi,000 psi 8,800 psi 0,000 psi 0,000 psi 0,000 psi 60,000 psi 60,000 psi 60,000 psi pproximate ir to Seat Valve 5 psi 5 psi 5 psi 5 psi 00 psi 00 psi 5 psi 00 psi 00 psi 00 psi 60 psi 60 psi 60 psi 55 psi 55 psi 55 psi Extra Heavy Duty 20-**LF2 20,000 psi /6" 55 psi 0-**NFF 0,000 psi /6" 45 psi 0-**NFH 0,000 psi /6" 45 psi 0-**LF6 0,000 psi /6" 45 psi 20-**LF6 20,000 psi /6" 55 psi 0-**LF6 0,000 psi /6" 50 psi ** Standard Valve Patterns (reference Page.4) Part Number Suffix MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO MPO-NO High Equipment Company R6 /0 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: Orifice Size /64" /64" 5/6" 5/6" /64" 5/6" /6" /6" /6" /6" 5/6" 5/6" /64" 5/6" /6" /6" /6" /6" /6" 5 psi 5 psi 55 psi 55 psi 5 psi 00 psi 00 psi 5 psi 5 psi 5 psi 0 psi 0 psi 0 psi HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO HPO-NO EHPO-NO EHPO-NO EHPO-NO EHPO-NO EHPO-NO EHPO-NO..5

72 High Equipment Remetco Piston Operated Fine Metering Valves For Liquids or ases Precise control with fast response is possible in fine metering applications to 60,000 psi with Remetco Valves. Pinpoint accuracy and repeatability are assured by a unique stem travel control device working in concert with a Conoflow operator, which is actuated by an input air pressure on only 5 psi. ody material is Type 6 stainless steel, with both stem and removable seat of -4PH. The stem tip is ground to a included taper, withorifice sizes as listed in the ordering table. Installation requires only connection to an air supply of 20 to 00 psi. This is connected both to the supply air connection and to the instrument air inlet. The latter is regulated between and 5 psi to actuate the valve to the desired position. Regulation is effected by the user s instrument or by the optional instrument panel at lower left. Thus the valve is in its full open position with a psi air input and in the closed position with a 5 psi air input. Failsafe operation. In standard configuration, the valve OPENS upon failure of the air supply. It may also be supplied to close upon air failure, to open upon an increase in air signal, or any combination of these specifications. Remote Valve Positioner RVP. Optional instrument panel shown at bottom can be ordered as an accessory. It is a manually operated remote air signal valve positioner which permits positioning the stem at any desired point within the travel of the stem. The dial indicator is graduated into 00 increments; thus each dial increment moves the stem 0.0. Standard inlet and outlet connections to the Remetco Valve are for /6" OD coned and threaded tubing. dapters may be supplied for other tubing sizes upon request. Shutoff not recommended. While this valve is capable of on-off operation, it is designed as a fine metering instrument. To assure maximum stem life, a manual on-off valve should be used in the line upstream of the Remetco Valve. To order, use assembly number in table and specify if operation is to be other than the standard closure upon air failure. dd RVP as suffix if remote air signal valve positioner is desired. Ordering Table ssembly Orifice Number Size 0M-2HFR 0,000 psi 0M-2HFR 0,000 psi 60M-2HFR 60,000 psi /6" OPTIONS: Stems & Seats.... Carbide (for cyclic service) Stellite (for cyclic service) Valve odies..... Hastelloy-C, Hastelloy Inconel 600, Inconel Incoloy 800, Incoloy Titanium rade 2, Titanium L4V Nickel Monel Packing PolyPak Temperature Considerations.... Extended stuffing box for temperatures from -42 F to,200 F (medium and high pressure connections only) " 2 Remote Valve Stem Positioner RVP above permits remote positioning of valve stem in increments of 0.0. To order, add suffix RVP to base order number..4 R2 2/

73 High Equipment ccessories High Equipment Company offers an extensive selection of accessory components to enable you to completely plumb a fluid system. These accessories allow you to move from tube to tube, tube to pipe, facilitate system pressure changes and monitor the temperatures and pressures within your system. dapters are available in both female to male and male to male configurations. dapter models exist for all HiP connections and in the various pressure ranges to complement our valve and fitting lines. Couplings enable you to make a wide variety of female to female connections. s with our adapters, couplings accommodate our complete line of valves and fittings. In addition, reducer couplings allow you to reduce line size within a given pressure range. Thermocouple adapters are an excellent method to provide for temperature measurement in pressure systems up to 5,000 psi. gauges are available in seven models to monitor system pressures ranging from atmosphere to 00,000 psi. Index Page Selection uide: Female to Female Couplings Female to Male dapters Male to Male dapters dapters: Female to Male dapters: Male to Male Fittings: NPT Hose Couplings: Female to Female Thermocouple dapters auges R 8/04 8.

74 High Equipment Female to Female F /6" Taper Seal F2 Taper Seal F4 Taper Seal F6 Taper Seal /6" TPER SEL TPER SEL TPER SEL TPER SEL MEDIUM PRESSURE MEDIUM PRESSURE /6" MEDIUM PRESSURE MEDIUM PRESSURE " MEDIUM PRESSURE HIH PRESSURE HIH PRESSURE HIH PRESSURE /6" HIH PRESSURE " HIH PRESSURE ULTR HIH PRESSURE ULTR HIH PRESSURE NPT PIPE NPT PIPE NPT PIPE NPT PIPE NPT PIPE " NPT PIPE F F2 F4 F6 LF4 LF6 LF LF2 LF6 HF2 HF4 HF6 HF HF6 XF4 XF6 NF NF NFC NFD NFF NFH 5-2F 5-2FF2 0-2FF4 0-2FF6 5-2FLF4 5-2FLF6 5-2FLF 5-2FLF2 5-2FLF6 5-2FHF2 5-2FHF4 5-2FHF6 5-2FHF 5-2FHF6 5-2FXF4 5-2FXF6 5-2FNF 5-2FNF 5-2FNFC 5-2FNFD 0-2FNFF 0-2FNFH 5-2FF2 5-2F2 0-2F2F4 0-2F2F6 5-2F2LF4 5-2F2LF6 5-2F2LF 5-2F2LF2 5-2F2LF6 5-2F2HF2 5-2F2HF4 5-2F2HF6 5-2F2HF 5-2F2HF6 5-2F2XF4 5-2F2XF6 5-2F2NF 5-2F2NF 5-2F2NFC 5-2F2NFD 0-2F2NFF 0-2F2NFH 0-2FF4 0-2F2F4 0-2F4 0-2F4F6 0-2F4LF4 0-2F4LF6 0-2F4LF 0-2F4LF2 0-2F4LF6 0-2F4HF2 0-2F4HF4 0-2F4HF6 0-2F4HF 0-2F4HF6 0-2F4XF4 0-2F4XF6 0-2F4NF 0-2F4NF 0-2F4NFC 0-2F4NFD 0-2F4NFF 0-2F4NFH 0-2FF6 0-2F2F6 0-2F4F6 0-2F6 0-2F6LF4 0-2F6LF6 0-2F6LF 0-2F6LF2 0-2F6LF6 0-2F6HF2 0-2F6HF4 0-2F6HF6 0-2F6HF 0-2F6HF6 0-2F6XF4 0-2F6XF6 0-2F6NF 0-2F6NF 0-2F6NFC 0-2F6NFD 0-2F6NFF 0-2F6NFH Female to Female (continued) HF6 High HF /6" High HF6 " High XF4 Ultra High /6" TPER SEL TPER SEL TPER SEL TPER SEL MEDIUM PRESSURE MEDIUM PRESSURE /6" MEDIUM PRESSURE MEDIUM PRESSURE " MEDIUM PRESSURE HIH PRESSURE HIH PRESSURE HIH PRESSURE /6" HIH PRESSURE " HIH PRESSURE ULTR HIH PRESSURE ULTR HIH PRESSURE NPT PIPE NPT PIPE NPT PIPE NPT PIPE NPT PIPE " NPT PIPE F F2 F4 F6 LF4 LF6 LF LF2 LF6 HF2 HF4 HF6 HF HF6 XF4 XF6 NF NF NFC NFD NFF NFH 5-2FHF6 5-2F2HF6 0-2F4HF6 0-2F6HF6 20-2LF4HF6 20-2LF6HF6 20-2LFHF6 20-2LF2HF6 20-2LF6HF6 60-2HF2HF6 60-2HF4HF6 60-2HF6 60-2HF6HF 0 2HF6HF6 60-2HF6XF4 60-2HF6XF6 0-2HF6NF 0-2HF6NF 0-2HF6NFC 0-2HF6NFD 0-2HF6NFF 0-2HF6NFH 5-2FHF 5-2F2HF 0-2F4HF 0-2F6HF 20-2LF4HF 20-2LF6HF 20-2LFHF 20-2LF2HF 20-2LF6HF 60-2HF2HF 60-2HF4HF 60-2HF6HF 60-2HF 0-2HFHF6 60-2HFXF4 60-2HFXF6 0-2HFNF 0-2HFNF 0-2HFNFC 0-2HFNFD 0-2HFNFF 0-2HFNFH 5-2FHF6 5-2F2HF6 0-2F4HF6 0-2F6HF6 20-2LF4HF6 20-2LF6HF6 20-2LFHF6 20-2LF2HF6 20-2LF6HF6 0-2HF2HF6 0-2HF4HF6 0-2HF6HF6 0-2HFHF6 0-2HF6 0-2HF6XF4 0-2HF6XF6 0-2HF6NF 0-2HF6NF 0-2HF6NFC 0-2HF6NFD 0-2HF6NFF 0-2HF6NFH 5-2FXF4 5-2F2XF4 0-2F4XF4 0-2F6XF4 20-2LF4XF4 20-2LF6XF4 20-2LFXF4 20-2LF2XF4 20-2LF6XF4 60-2HF2XF4 60-2HF4XF4 60-2HF6XF4 60-2HFXF4 0-2HF6XF4 00-2XF4 00-2XF4XF6 0-2XF4NF 0-2XF4NF 0-2XF4NFC 0-2XF4NFD 0-2XF4NFF 0-2XF4NFH 8.2

75 Coupling Selection uide LF4 LF6 LF LF2 LF6 HF2 HF4 Medium Medium /6" Medium Medium " Medium High High 5-2FLF4 5-2F2LF4 0-2F4LF4 0-2F6LF4 20-2LF4 20-2LF4LF6 20-2LF4LF 20-2LF4LF2 20-2LF4LF6 20-2LF4HF2 20-2LF4HF4 20-2LF4HF6 20-2LF4HF 20-2LF4HF6 20-2LF4XF4 20-2LF4XF6 20-2LF4NF 20-2LF4NF 20-2LF4NFC 20-2LF4NFD 0-2LF4NFF 0-2LF4NFH 5-2FLF6 5-2F2LF6 0-2F4LF6 0-2F6LF6 20-2LF4LF6 20-2LF6 20-2LF6LF 20-2LF6LF2 20-2LF6LF6 20-2LF6HF2 20-2LF6HF4 20-2LF6HF6 20-2LF6HF 20-2LF6HF6 20-2LF6XF4 20-2LF6XF6 20-2LF6NF 20-2LF6NF 20-2LF6NFC 20-2LF6NFD 0-2LF6NFF 0-2LF6NFH 5-2FLF 5-2F2LF 0-2F4LF 0-2F6LF 0-2LF4LF 20-2LF6LF 20-2LF 20-2LFLF2 20-2LFLF6 20-2LFHF2 20-2LFHF4 20-2LFHF6 20-2LFHF 20-2LFHF6 20-2LFXF4 20-2LFXF6 20-2LFNF 20-2LFNF 20-2LFNFC 20-2LFNFD 0-2LFNFF 0-2LFNFH 5-2FLF2 5-2F2LF2 0-2F4LF2 0-2F6LF2 20-2LF4LF2 20-2LF6LF2 20-2LFLF2 20-2LF2 20-2LF2LF6 20-2LF2HF2 20-2LF2HF4 20-2LF2HF6 20-2LF2HF 20-2LF2HF6 20-2LF2XF4 20-2LF2XF6 20-2LF2NF 20-2LF2NF 20-2LF2NFC 20-2LF2NFD 0-2LF2NFF 0-2LF2NFH 5-2FLF6 5-2F2LF6 0-2F4LF6 0-2F6LF6 20-2LF4LF6 20-2LF6LF6 20-2LFLF6 20-2LF2LF6 20-2LF6 20-2LF6HF2 20-2LF6HF4 20-2LF6HF6 20-2LF6HF 20 2LF6HF6 20-2LF6XF4 20-2LF6XF6 20-2LF6NF 20-2LF6NF 20-2LF6NFC 20-2LF6NFD 0-2LF6NFF 0-2LF6NFH 5-2FHF2 5-2F2HF2 0-2F4HF2 0-2F6HF2 20-2LF4HF2 20-2LF6HF2 20-2LFHF2 20-2LF2HF2 20-2LF6HF2 60-2HF2 60-2HF2HF4 60-2HF2HF6 60-2HF2HF 0-2HF2HF6 60-2HF2XF4 60-2HF2XF6 0-2HF2NF 0-2HF2NF 0-2HF2NFC 0-2HF2NFD 0-2HF2NFF 0-2HF2NFH 5-2FHF4 5-2F2HF4 0-2F4HF4 0-2F6HF4 20-2LF4HF4 20-2LF6HF4 20-2LFHF4 20-2LF2HF4 20-2LF6HF4 60-2HF2HF4 60-2HF4 60-2HF4HF6 60-2HF4HF 0-2HF4HF6 60-2HF4XF4 60-2HF4XF6 0-2HF4NF 0-2HF4NF 0-2HF4NFC 0-2HF4NFD 0-2HF4NFF 0-2HF4NFH XF6 NF NF NFC NFD NFF NFH Ultra High NPT Pipe NPT Pipe NPT Pipe NPT Pipe NPT Pipe " NPT Pipe 5-2FXF6 5-2F2XF6 0-2F4XF6 0-2F6XF6 20-2LF4XF6 20-2LF6XF6 20-2LFXF6 20-2LF2XF6 20-2LF6XF6 60-2HF2XF6 60-2HF4XF6 60-2HF6XF6 60-2HFXF6 0-2HF6XF6 00-2XF4XF6 50-2XF6 0-2XF6NF 0-2XF6NF 0-2XF6NFC 0-2XF6NFD 0-2XF6NFF 0-2XF6NFH 5-2FNF 5-2F2NF 0-2F4NF 0-2F6NF 20-2LF4NF 20-2LF6NF 20-2LFNF 20-2LF2NF 20-2LF6NF 0-2HF2NF 0-2HF4NF 0-2HF6NF 0-2HFNF 0-2HF6NF 0-2XF4NF 0-2XF6NF 5-2NF 5-2NFNF 5-2NFNFC 5-2NFNFD 0-2NFNFF 0-2NFNFH 5-2FNF 5-2F2NF 0-2F4NF 0-2F6NF 20-2LF4NF 20-2LF6NF 20-2LFNF 20-2LF2NF 20-2LF6NF 0-2HF2NF 0-2HF4NF 0-2HF6NF 0-2HFNF 0-2HF6NF 0-2XF4NF 0-2XF6NF 5-2NFNF 5-2NF 5-2NFNFC 5-2NFNFD 0-2NFNFF 0-2NFNFH 5-2FNFC 5-2F2NFC 0-2F4NFC 0-2F6NFC 20-2LF4NFC 20-2LF6NFC 20-2LFNFC 20-2LF2NFC 20-2LF6NFC 0-2HF2NFC 0-2HF4NFC 0-2HF6NFC 0-2HFNFC 0-2HF6NFC 0-2XF4NFC 0-2XF6NFC 5-2NFNFC 5-2NFNFC 5-2NFC 5-2NFCNFD 0-2NFCNFF 0-2NFCNFH 5-2FNFD 5-2F2NFD 0-2F4NFD 0-2F6NFD 20-2LF4NFD 20-2LF6NFD 20-2LFNFD 20-2LF2NFD 20-2LF6NFD 0-2HF2NFD 0-2HF4NFD 0-2HF6NFD 0-2HFNFD 0-2HF6NFD 0-2XF4NFD 0-2XF6NFD 5-2NFNFD 5-2NFNFD 5-2NFCNFD 5-2NFD 0-2NFDNFF 0-2NFDNFH 0-2FNFF 0-2F2NFF 0-2F4NFF 0-2F6NFF 0-2LF4NFF 0-2LF6NFF 0-2LFNFF 0-2LF2NFF 0-2LF6NFF 0-2HF2NFF 0-2HF4NFF 0-2HF6NFF 0-2HFNFF 0-2HF6NFF 0-2XF4NFF 0-2XF6NFF 0-2NFNFF 0-2NFNFF 0-2NFCNFF 0-2NFDNFF 0-2NFF 0-2NFFNFH 0-2FNFH 0-2F2NFH 0-2F4NFH 0-2F6NFH 0-2LF4NFH 0-2LF6NFH 0-2LFNFH 0-2LF2NFH 0-2LF6NFH 0-2HF2NFH 0-2HF4NFH 0-2HF6NFH 0-2HFNFH 0-2HF6NFH 0-2XF4NFH 0-2XF6NFH 0-2NFNFH 0-2NFNFH 0-2NFCNFH 0-2NFDNFH 0-2NFFNFH 0-2NFH High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.

76 High Equipment Female to Male M /6" Taper Seal M2 Taper Seal M4 Taper Seal M6 Taper Seal /6" TPER SEL TPER SEL TPER SEL TPER SEL MEDIUM PRESSURE MEDIUM PRESSURE /6" MEDIUM PRESSURE MEDIUM PRESSURE " MEDIUM PRESSURE HIH PRESSURE HIH PRESSURE HIH PRESSURE /6" HIH PRESSURE " HIH PRESSURE ULTR HIH PRESSURE ULTR HIH PRESSURE NPT PIPE NPT PIPE NPT PIPE NPT PIPE NPT PIPE " NPT PIPE F F2 F4 F6 LF4 LF6 LF LF2 LF6 HF2 HF4 HF6 HF HF6 XF4 XF6 NF NF NFC NFD NFF NFH 5-2FM 5-2F2M 0-2F4M 0-2F6M 5-2LF4M 5-2LF6M 5-2LFM 5-2LF2M 5-2LF6M 5-2HF2M 5-2HF4M 5-2HF6M 5-2HFM 5-2HF6M 5-2XF4M 5-2XF6M 5-2NFM 5-2NFM 5-2NFCM 5-2NFDM 0-2NFFM 0-2NFHM 5-2FM2 5-2F2M2 0-2F4M2 0-2F6M2 5-2LF4M2 5-2LF6M2 5-2LFM2 5-2LF2M2 5-2LF6M2 5-2HF2M2 5-2HF4M2 5-2HF6M2 5-2HFM2 5-2HF6M2 5-2XF4M2 5-2XF6M2 5-2NFM2 5-2NFM2 5-2NFCM2 5-2NFDM2 0-2NFFM2 0-2NFHM2 0-2FM4 0-2F2M4 0-2F4M4 0-2F6M4 0-2LF4M4 0-2LF6M4 0-2LFM4 0-2LF2M4 0-2LF6M4 0-2HF2M4 0-2HF4M4 0-2HF6M4 0-2HFM4 0-2HF6M4 0-2XF4M4 0-2XF6M4 0-2NFM4 0-2NFM4 0-2NFCM4 0-2NFDM4 0-2NFFM4 0-2NFHM4 0-2FM6 0-2F2M6 0-2F4M6 0-2F6M6 0-2LF4M6 0-2LF6M6 0-2LFM6 0-2LF2M6 0-2LF6M6 0-2HF2M6 0-2HF4M6 0-2HF6M6 0-2HFM6 0-2HF6M6 0-2XF4M6 0-2XF6M6 0-2NFM6 0-2NFM6 0-2NFCM6 0-2NFDM6 0-2NFFM6 0-2NFHM6 Female to Male (continued) HM6 High HM /6" High HM6 " High XM4 Ultra High /6" TPER SEL TPER SEL TPER SEL TPER SEL MEDIUM PRESSURE MEDIUM PRESSURE /6" MEDIUM PRESSURE MEDIUM PRESSURE " MEDIUM PRESSURE HIH PRESSURE HIH PRESSURE HIH PRESSURE /6" HIH PRESSURE " HIH PRESSURE ULTR HIH PRESSURE ULTR HIH PRESSURE NPT PIPE NPT PIPE NPT PIPE NPT PIPE NPT PIPE " NPT PIPE F F2 F4 F6 LF4 LF6 LF LF2 LF6 HF2 HF4 HF6 HF HF6 XF4 XF6 NF NF NFC NFD NFF NFH 5-2FHM6 5-2F2HM6 0-2F4HM6 0-2F6HM6 20-2LF4HM6 20-2LF6HM6 20-2LFHM6 20-2LF2HM6 20-2LF6HM6 60-2HF2HM6 60-2HF4HM6 60-2HF6HM6 60-2HFHM6 0-2HF6HM6 60-2XF4HM6 60-2XF6HM6 0-2NFHM6 0-2NFHM6 0-2NFCHM6 0-2NFDHM6 0-2NFFHM6 0-2NFHHM6 5-2FHM 5-2F2HM 0-2F4HM 0-2F6HM 20-2LF4HM 20-2LF6HM 20-2LFHM 20-2LF2HM 20-2LF6HM 60-2HF2HM 60-2HF4HM 60-2HF6HM 60-2HFHM 0-2HF6HM 60-2XF4HM 60-2XF6HM 0-2NFHM 0-2NFHM 0-2NFCHM 0-2NFDHM 0-2NFFHM 0-2NFHHM 5-2FHM6 5-2F2HM6 0-2F4HM6 0-2F6HM6 20-2LF4HM6 20-2LF6HM6 20-2LFHM6 20-2LF2HM6 20-2LF6HM6 0-2HF2HM6 0-2HF4HM6 0-2HF6HM6 0-2HFHM6 0-2HF6HM6 0-2XF4HM6 0-2XF6HM6 0-2NFHM6 0-2NFHM6 0-2NFCHM6 0-2NFDHM6 0-2NFFHM6 0-2NFHHM6 5-2FXM4 5-2F2XM4 0-2F4XM4 0-2F6XM4 20-2LF4XM4 20-2LF6XM4 20-2LFXM4 20-2LF2XM4 20-2LF6XM4 60-2HF2XM4 60-2HF4XM4 60-2HF6XM4 60-2HFXM4 0-2HF6XM4 00-2XF4XM4 00-2XF6XM4 0-2NFXM4 0-2NFXM4 0-2NFCXM4 0-2NFDXM4 0-2NFFXM4 0-2NFHXM4 8.4

77 dapter Selection uide LM4 LM6 LM LM2 LM6 HM2 HM4 Medium Medium /6" Medium Medium " Medium High High 5-2FLM4 5-2F2LM4 0-2F4LM4 0-2F6LM4 20-2LF4LM4 20-2LF6LM4 20-2LFLM4 20-2LF2LM4 20-2LF6LM4 20-2HF2LM4 20-2HF4LM4 20-2HF6LM4 20-2HFLM4 20 2HF6LM4 20-2XF4LM4 20-2XF6LM4 20-2NFLM4 20-2NFLM4 20-2NFCLM4 20-2NFDLM4 0-2NFFLM4 0-2NFHLM4 5-2FLM6 5-2F2LM6 0-2F4LM6 0-2F6LM6 20-2LF4LM6 20-2LF6LM6 20-2LFLM6 20-2LF2LM6 20-2LF6LM6 20-2HF2LM6 20-2HF4LM6 20-2HF6LM6 20-2HFLM6 20-2HF6LM6 20-2XF4LM6 20-2XF6LM6 20-2NFLM6 20-2NFLM6 20-2NFCLM6 20-2NFDLM6 0-2NFFLM6 0-2NFHLM6 5-2FLM 5-2F2LM 0-2F4LM 0-2F6LM 20-2LF4LM 20-2LF6LM 20-2LFLM 20-2LF2LM 20-2LF6LM 20-2HF2LM 20-2HF4LM 20-2HF6LM 20-2HFLM 20-2HF6LM 20-2XF4LM 20-2XF6LM 20-2NFLM 20-2NFLM 20-2NFCLM 20-2NFDLM 0-2NFFLM 0-2NFHLM 5-2FLM2 5-2F2LM2 0-2F4LM2 0-2F6LM2 20-2LF4LM2 20-2LF6LM2 20-2LFLM2 20-2LF2LM2 20-2LF6LM2 20-2HF2LM2 20-2HF4LM2 20-2HF6LM2 20-2HFLM2 20-2HF6LM2 20-2XF4LM2 20-2XF6LM2 20-2NFLM2 20-2NFLM2 20-2NFCLM2 20-2NFDLM2 0-2NFFLM2 0-2NFHLM2 5-2FLM6 5-2F2LM6 0-2F4LM6 0-2F6LM6 20-2LF4LM6 20-2LF6LM6 20-2LFLM6 20-2LF2LM6 20-2LF6LM6 20-2HF2LM6 20-2HF4LM6 20-2HF6LM6 20-2HFLM6 20-2HF6LM6 20-2XF4LM6 20-2XF6LM6 20-2NFLM6 20-2NFLM6 20-2NFCLM6 20-2NFDLM6 0-2NFFLM6 0-2NFHLM6 5-2FHM2 5-2F2HM2 0-2F4HM2 0-2F6HM2 20-2LF4HM2 20-2LF6HM2 20-2LFHM2 20-2LF2HM2 20-2LF6HM2 60-2HF2HM2 60-2HF4HM2 60-2HF6HM2 60-2HFHM2 0-2HF6HM2 60-2XF4HM2 60-2XF6HM2 0-2NFHM2 0-2NFHM2 0-2NFCHM2 0-2NFDHM2 0-2NFFHM2 0-2NFHHM2 5-2FHM4 5-2F2HM4 0-2F4HM4 0-2F6HM4 20-2LF4HM4 20-2LF6HM4 20-2LFHM4 20-2LF2HM4 20-2LF6HM4 60-2HF2HM4 60-2HF4HM4 60-2HF6HM4 60-2HFHM4 0-2HF6HM4 60-2XF4HM4 60-2XF6HM4 0-2NFHM4 0-2NFHM4 0-2NFCHM4 0-2NFDHM4 0-2NFFHM4 0-2NFHHM4 XM6 NM NM NMC NMD NMF NMH Ultra High NPT Pipe NPT Pipe NPT Pipe NPT Pipe NPT Pipe " NPT Pipe 5-2FXM6 5-2F2XM6 0-2F4XM6 0-2F6XM6 20-2LF4XM6 20-2LF6XM6 20-2LFXM6 20-2LF2XM6 20-2LF6XM6 60-2HF2XM6 60-2HF4XM6 60-2HF6XM6 60-2HFXM6 0-2HF6XM6 00-2XF4XM6 50-2XF6XM6 0-2NFXM6 0-2NFXM6 0-2NFCXM6 0-2NFDXM6 0-2NFFXM6 0-2NFHXM6 5-2FNM 5-2F2NM 0-2F4NM 0-2F6NM 20-2LF4NM 20-2LF6NM 20-2LFNM 20-2LF2NM 20-2LF6NM 0-2HF2NM 0-2HF4NM 0-2HF6NM 0-2HFNM 0-2HF6NM 0-2XF4NM 0-2XF6NM 5-2NFNM 5-2NFNM 5-2NFCNM 5-2NFDNM 0-2NFFNM 0-2NFHNM 5-2FNM 5-2F2NM 0-2F4NM 0-2F6NM 20-2LF4NM 20-2LF6NM 20-2LFNM 20-2LF2NM 20-2LF6NM 0-2HF2NM 0-2HF4NM 0-2HF6NM 0-2HFNM 0-2HF6NM 0-2XF4NM 0-2XF6NM 5-2NFNM 5-2NFNM 5-2NFCNM 5-2NFDNM 0-2NFFNM 0-2NFHNM 5-2FNMC 5-2F2NMC 0-2F4NMC 0-2F6NMC 20-2LF4NMC 20-2LF6NMC 20-2LFNMC 20-2LF2NMC 20-2LF6NMC 0-2HF2NMC 0-2HF4NMC 0-2HF6NMC 0-2HFNMC 0-2HF6NMC 0-2XF4NMC 0-2XF6NMC 5-2NFNMC 5-2NFNMC 5-2NFCNMC 5-2NFDNMC 0-2NFFNMC 0-2NFHNMC 5-2FNMD 5-2F2NMD 0-2F4NMD 0-2F6NMD 20-2LF4NMD 20-2LF6NMD 20-2LFNMD 20-2LF2NMD 20-2LF6NMD 0-2HF2NMD 0-2HF4NMD 0-2HF6NMD 0-2HFNMD 0-2HF6NMD 0-2XF4NMD 0-2XF6NMD 5-2NFNMD 5-2NFNMD 5-2NFCNMD 5-2NFDNMD 0-2NFFNMD 0-2NFHNMD 0-2FNMF 0-2F2NMF 0-2F4NMF 0-2F6NMF 0-2LF4NMF 0-2LF6NMF 0-2LFNMF 0-2LF2NMF 0-2LF6NMF 0-2HF2NMF 0-2HF4NMF 0-2HF6NMF 0-2HFNMF 0-2HF6NMF 0-2XF4NMF 0-2XF6NMF 0-2NFNMF 0-2NFNMF 0-2NFCNMF 0-2NFDNMF 0-2NFFNMF 0-2NFHNMF 0-2FNMH 0-2F2NMH 0-2F4NMH 0-2F6NMH 0-2LF4NMH 0-2LF6NMH 0-2LFNMH 0-2LF2NMH 0-2LF6NMH 0-2HF2NMH 0-2HF4NMH 0-2HF6NMH 0-2HFNMH 0-2HF6NMH 0-2XF4NMH 0-2XF6NMH 0-2NFNMH 0-2NFNMH 0-2NFCNMH 0-2NFDNMH 0-2NFFNMH 0-2NFHNMH High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.5

78 High Equipment Male to Male M /6" Taper Seal M2 Taper Seal M4 Taper Seal M6 Taper Seal /6" TPER SEL TPER SEL TPER SEL TPER SEL MEDIUM PRESSURE MEDIUM PRESSURE /6" MEDIUM PRESSURE MEDIUM PRESSURE " MEDIUM PRESSURE HIH PRESSURE HIH PRESSURE HIH PRESSURE /6" HIH PRESSURE " HIH PRESSURE ULTR HIH PRESSURE ULTR HIH PRESSURE NPT PIPE NPT PIPE NPT PIPE NPT PIPE NPT PIPE " NPT PIPE M M2 M4 M6 LM4 LM6 LM LM2 LM6 HM2 HM4 HM6 HM HM6 XM4 XM6 NM NM NMC NMD NMF NMH 5-2MM 5-2MM2 0-2MM4 0-2MM6 5-2MLM4 5-2MLM6 5-2MLM 5-2MLM2 5-2MLM6 5-2MHM2 5-2MHM4 5-2MHM6 5-2MHM 5-2MHM6 5-2MXM4 5-2MXM6 5-2MNM 5-2MNM 5-2MNMC 5-2MNMD 0-2MNMF 0-2MNMH 5-2MM2 5-2M2M2 0-2M2M4 0-2M2M6 5-2M2LM4 5-2M2LM6 5-2M2LM 5-2M2LM2 5-2M2LM6 5-2M2HM2 5-2M2HM4 5-2M2HM6 5-2M2HM 5-2M2HM6 5-2M2XM4 5-2M2XM6 5-2M2NM 5-2M2NM 5-2M2NMC 5-2M2NMD 0-2M2NMF 0-2M2NMH 0-2MM4 0-2M2M4 0-2M4M4 0-2M4M6 0-2M4LM4 0-2M4LM6 0-2M4LM 0-2M4LM2 0-2M4LM6 0-2M4HM2 0-2M4HM4 0-2M4HM6 0-2M4HM 0-2M4HM6 0-2M4XM4 0-2M4XM6 0-2M4NM 0-2M4NM 0-2M4NMC 0-2M4NMD 0-2M4NMF 0-2M4NMH 0-2MM6 0-2M2M6 0-2M4M6 0-2M6M6 0-2M6LM4 0-2M6LM6 0-2M6LM 0-2M6LM2 0-2M6LM6 0-2M6HM2 0-2M6HM4 0-2M6HM6 0-2M6HM 0-2M6HM6 0-2M6XM4 0-2M6XM6 0-2M6NM 0-2M6NM 0-2M6NMC 0-2M6NMD 0-2M6NMF 0-2M6NMH Male to Male (continued) HM6 High HM /6" High HM6 " High XM4 Ultra High /6" TPER SEL TPER SEL TPER SEL TPER SEL MEDIUM PRESSURE MEDIUM PRESSURE /6" MEDIUM PRESSURE MEDIUM PRESSURE " MEDIUM PRESSURE HIH PRESSURE HIH PRESSURE HIH PRESSURE /6" HIH PRESSURE " HIH PRESSURE ULTR HIH PRESSURE ULTR HIH PRESSURE NPT PIPE NPT PIPE NPT PIPE NPT PIPE NPT PIPE " NPT PIPE M M2 M4 M6 LM4 LM6 LM LM2 LM6 HM2 HM4 HM6 HM HM6 XM4 XM6 NM NM NMC NMD NMF NMH 5-2MHM6 5-2M2HM6 0-2M4HM6 0-2M6HM6 20-2LM4HM6 20-2LM6HM6 20-2LMHM6 20-2LM2HM6 20-2LM6HM6 60-2HM2HM6 60-2HM4HM6 60-2HM6HM6 60-2HMHM6 0-2HM6HM6 60-2HM6XM4 60-2HM6XM6 0-2HM6NM 0-2HM6NM 0-2HM6NMC 0-2HM6NMD 0-2HM6NMF 0-2HM6NMH 5-2MHM 5-2M2HM 0-2M4HM 0-2M6HM 20-2LM4HM 20-2LM6HM 20-2LMHM 20-2LM2HM 20-2LM6HM 60-2HM2HM 60-2HM4HM 60-2HM6HM 60-2HMHM 0-2HMHM6 60-2HMXM4 60-2HMXM6 0-2HMNM 0-2HMNM 0-2HMNMC 0-2HMNMD 0-2HMNMF 0-2HMNMH 5-2MHM6 5-2M2HM6 0-2M4HM6 0-2M6HM6 20-2LM4HM6 20-2LM6HM6 20-2LMHM6 20-2LM2HM6 20-2LM6HM6 60-2HM2HM6 60-2HM4HM6 60-2HM6HM6 0-2HMHM6 0-2HM6HM6 60-2HM6XM4 60-2HM6XM6 0-2HM6NM 0-2HM6NM 0-2HM6NMC 0-2HM6NMD 0-2HM6NMF 0-2HM6NMH 5-2MXM4 5-2M2XM4 0-2M4XM4 0-2M6XM4 20-2LM4XM4 20-2LM6XM4 20-2LMXM4 20-2LM2XM4 20-2LM6XM4 60-2HM2XM4 60-2HM4XM4 60-2HM6XM4 60-2HMXM4 0-2HM6XM4 00-2XM4XM4 00-2XM4XM6 0-2XM4NM 0-2XM4NM 0-2XM4NMC 0-2XM4NMD 0-2XM4NMF 0-2XM4NMH 8.6 R 2/

79 dapter Selection uide LM4 LM6 LM LM2 LM6 HM2 HM4 Medium Medium /6" Medium Medium " Medium High High 5-2MLM4 5-2M2LM4 0-2M4LM4 0-2M6LM4 20-2LM4LM4 20-2LM4LM6 20-2LM4LM 20-2LM4LM2 20-2LM4LM6 20-2LM4HM2 20-2LM4HM4 20-2LM4HM6 20-2LM4HM 20-2LM4HM6 20-2LM4XM4 20-2LM4XM6 20-2LM4NM 20-2LM4NM 20-2LM4NMC 20-2LM4NMD 0-2LM4NMF 0-2LM4NMH 5-2MLM6 5-2M2LM6 0-2M4LM6 0-2M6LM6 20-2LM4LM6 20-2LM6LM6 20-2LM6LM 20-2LM6LM2 20-2LM6LM6 20-2LM6HM2 20-2LM6HM4 20-2LM6HM6 20-2LM6HM 20-2LM6HM6 20-2LM6XM4 20-2LM6XM6 20-2LM6NM 20-2LM6NM 20-2LM6NMC 20-2LM6NMD 0-2LM6NMF 0-2LM6NMH 5-2MLM 5-2M2LM 0-2M4LM 0-2M6LM 0-2LM4LM 20-2LM6LM 20-2LMLM 20-2LMLM2 20-2LMLM6 20-2LMHM2 20-2LMHM4 20-2LMHM6 20-2LMHM 20-2LMHM6 20-2LMXM4 20-2LMXM6 20-2LMNM 20-2LMNM 20-2LMNMC 20-2LMNMD 0-2LMNMF 0-2LMNMH 5-2MLM2 5-2M2LM2 0-2M4LM2 0-2M6LM2 20-2LM4LM2 20-2LM6LM2 20-2LMLM2 20-2LM2LM2 20-2LM2LM6 20-2LM2HM2 20-2LM2HM4 20-2LM2HM6 20-2LM2HM 20-2LM2HM6 20-2LM2XM4 20-2LM2XM6 20-2LM2NM 20-2LM2NM 20-2LM2NMC 20-2LM2NMD 0-2LM2NMF 0-2LM2NMH 5-2MLM6 5-2M2LM6 0-2M4LM6 0-2M6LM6 20-2LM4LM6 20-2LM6LM6 20-2LMLM6 20-2LM2LM6 20-2LM6LM6 20-2LM6HM2 20-2LM6HM4 20-2LM6HM6 20-2LM6HM 20-2LM6HM6 20-2LM6XM4 20-2LM6XM6 20-2LM6NM 20-2LM6NM 20-2LM6NMC 20-2LM6NMD 0-2LM6NMF 0-2LM6NMH 5-2MHM2 5-2M2HM2 0-2M4HM2 0-2M6HM2 20-2LM4HM2 20-2LM6HM2 20-2LMHM2 20-2LM2HM2 20-2LM6HM2 60-2HM2HM2 60-2HM2HM4 60-2HM2HM6 60-2HM2HM 0-2HM2HM6 60-2HM2XM4 60-2HM2XM6 0-2HM2NM 0-2HM2NM 0-2HM2NMC 0-2HM2NMD 0-2HM2NMF 0-2HM2NMH 5-2MHM4 5-2M2HM4 0-2M4HM4 0-2M6HM4 20-2LM4HM4 20-2LM6HM4 20-2LMHM4 20-2LM2HM4 20-2LM6HM4 60-2HM2HM4 60-2HM4HM4 60-2HM4HM6 60-2HM4HM 0-2HM4HM6 60-2HM4XM4 60-2HM4XM6 0-2HM4NM 0-2HM4NM 0-2HM4NMC 0-2HM4NMD 0-2HM4NMF 0-2HM4NMH XM6 NM NM NMC NMD NMF NMH Ultra High NPT Pipe NPT Pipe NPT Pipe NPT Pipe NPT Pipe " NPT Pipe 5-2MXM6 5-2M2XM6 0-2M4XM6 0-2M6XM6 20-2LM4XM6 20-2LM6XM6 20-2LMXM6 20-2LM2XM6 20-2LM6XM6 60-2HM2XM6 60-2HM4XM6 60-2HM6XM6 60-2HMXM6 0-2HM6XM6 00-2XM4XM6 50-2XM6XM6 0-2XM6NM 0-2XM6NM 0-2XM6NMC 0-2XM6NMD 0-2XM6NMF 0-2XM6NMH 5-2MNM 5-2M2NM 0-2M4NM 0-2M6NM 20-2LM4NM 20-2LM6NM 20-2LMNM 20-2LM2NM 20-2LM6NM 0-2HM2NM 0-2HM4NM 0-2HM6NM 0-2HMNM 0-2HM6NM 0-2XM4NM 0-2XM6NM 5-2NMNM 5-2NMNM 5-2NMNMC 5-2NMNMD 0-2NMNMF 0-2NMNMH 5-2MNM 5-2M2NM 0-2M4NM 0-2M6NM 20-2LM4NM 20-2LM6NM 20-2LMNM 20-2LM2NM 20-2LM6NM 0-2HM2NM 0-2HM4NM 0-2HM6NM 0-2HMNM 0-2HM6NM 0-2XM4NM 0-2XM6NM 5-2NMNM 5-2NMNM 5-2NMNMC 5-2NMNMD 0-2NMNMF 0-2NMNMH 5-2MNMC 5-2M2NMC 0-2M4NMC 0-2M6NMC 20-2LM4NMC 20-2LM6NMC 20-2LMNMC 20-2LM2NMC 20-2LM6NMC 0-2HM2NMC 0-2HM4NMC 0-2HM6NMC 0-2HMNMC 0-2HM6NMC 0-2XM4NMC 0-2XM6NMC 5-2NMNMC 5-2NMNMC 5-2NMCNMC 5-2NMCNMD 0-2NMCNMF 0-2NMCNMH 5-2MNMD 5-2M2NMD 0-2M4NMD 0-2M6NMD 20-2LM4NMD 20-2LM6NMD 20-2LMNMD 20-2LM2NMD 20-2LM6NMD 0-2HM2NMD 0-2HM4NMD 0-2HM6NMD 0-2HMNMD 0-2HM6NMD 0-2XM4NMD 0-2XM6NMD 5-2NMNMD 5-2NMNMD 5-2NMCNMD 5-2NMDNMD 0-2NMDNMF 0-2NMDNMH 0-2MNMF 0-2M2NMF 0-2M4NMF 0-2M6NMF 0-2LM4NMF 0-2LM6NMF 0-2LMNMF 0-2LM2NMF 0-2LM6NMF 0-2HM2NMF 0-2HM4NMF 0-2HM6NMF 0-2HMNMF 0-2HM6NMF 0-2XM4NMF 0-2XM6NMF 0-2NMNMF 0-2NMNMF 0-2NMCNMF 0-2NMDNMF 0-2NMFNMF 0-2NMFNMH 0-2MNMH 0-2M2NMH 0-2M4NMH 0-2M6NMH 0-2LM4NMH 0-2LM6NMH 0-2LMNMH 0-2LM2NMH 0-2LM6NMH 0-2HM2NMH 0-2HM4NMH 0-2HM6NMH 0-2HMNMH 0-2HM6NMH 0-2XM4NMH 0-2XM6NMH 0-2NMNMH 0-2NMNMH 0-2NMCNMH 0-2NMDNMH 0-2NMFNMH 0-2NMHNMH High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.

80 High Equipment dapters: Female to Male complete range of adapters is offered for flexibility in going from tube to tube and from tube to pipe. ll standard adapter bodies are made from high tensile 6 stainless steel. Standard tubing glands and collars (sleeves) are provided with adapters unless otherwise specified. Female Taper Seal to Male Taper Seal Hex Catalog No. psi Connections Length Size 5-2FM2 5,000 /6" O.D. TUE TO TPER SEL F M2 5 /6" 5 0-2FM4 0,000 /6" O.D. TUE TO TPER SEL F M4 0-2FM6 0,000 /6" O.D. TUE TO TPER SEL F M6 0-2F2M4 0,000 O.D. TUE TO TPER SEL F2 M4 0-2F2M6 0,000 O.D. TUE TO TPER SEL F2 M6 Female Taper Seal to Male High Catalog No. psi Connections Length Hex Size 5-2FHM2 5,000 /6" T.S. TO H.P. MLE F HM2 5-2FHM4 5,000 /6" T.S. TO H.P. MLE F HM FHM6 5,000 /6" T.S. TO H.P. MLE F HM6 5-2FHM 5,000 /6" T.S. TO /6" H.P. MLE F HM 2 5-2F2HM2 5,000 T.S. TO H.P. MLE F2 HM F2HM4 5,000 T.S. TO H.P. MLE F2 HM F2HM6 5,000 T.S. TO H.P. MLE F2 HM6 5-2F2HM 5,000 T.S. TO /6" H.P. MLE F2 HM 2 0-2F4HM2 0,000 T.S. TO H.P. MLE F4 HM2 /6" " 0-2F4HM4 0,000 T.S. TO H.P. MLE F4 HM4 " 0-2F4HM6 0,000 T.S. TO H.P. MLE F4 HM6 5 " 0-2F4HM 0,000 T.S. TO /6" H.P. MLE F4 HM 2 0-2F6HM2 0,000 T.S. TO H.P. MLE F6 HM2 " 0-2F6HM4 0,000 T.S. TO H.P. MLE F6 HM4 " 0-2F6HM6 0,000 T.S. TO H.P. MLE F6 HM6 " 0-2F6HM 0,000 T.S. TO /6" H.P. MLE F6 HM R2 2/

81 Female to Male dapters Female Taper Seal to Male Pipe Hex Catalog No. psi Connections Length Size 5-2FNM 5,000 /6" T.S. TO NPT MLE F NM " 5-2FNM 5,000 /6" T.S. TO NPT MLE F NM 5 5-2FNMC 5,000 /6" T.S. TO NPT MLE F NMC 5-2FNMD 5,000 /6" T.S. TO NPT MLE F NMD " 5-2FNMF 5,000 /6" T.S. TO NPT MLE F NMF 5 5-2FNMH 5,000 /6" T.S. TO " NPT MLE F NMH 5 5-2F2NM 5,000 T.S. TO NPT MLE F2 NM 5-2F2NM 5,000 T.S. TO NPT MLE F2 NM 5 5-2F2NMC 5,000 T.S. TO NPT MLE F2 NMC 5-2F2NMD 5,000 T.S. TO NPT MLE F2 NMD " 5-2F2NMF 5,000 T.S. TO NPT MLE F2 NMF 5 5-2F2NMH 5,000 T.S. TO " NPT MLE F2 NMH 5 0-2F4NM 0,000 T.S. TO NPT MLE F4 NM " 0-2F4NM 0,000 T.S. TO NPT MLE F4 NM 5 " 0-2F4NMC 0,000 T.S. TO NPT MLE F4 NMC 5 " 0-2F4NMD 0,000 T.S. TO NPT MLE F4 NMD " 0-2F4NMF 0,000 T.S. TO NPT MLE F4 NMF 0-2F4NMH 0,000 T.S. TO " NPT MLE F4 NMH 0-2F6NM 0,000 T.S. TO NPT MLE F6 NM " 0-2F6NM 0,000 T.S. TO NPT MLE F6 NM 5 " 0-2F6NMC 0,000 T.S. TO NPT MLE F6 NMC 5 " 0-2F6NMD 0,000 T.S. TO NPT MLE F6 NMD " 0-2F6NMF 0,000 T.S. TO NPT MLE F6 NMF 0-2F6NMH 0,000 T.S. TO " NPT MLE F6 NMH Female High to Male High Hex Catalog No. psi Connections Length Size 60-2HF2HM4 60,000 O.D. TUE TO H.P. HF2 HM HF2HM6 60,000 O.D. TUE TO H.P. HF2 HM6 60-2HF2HM 60,000 O.D. TUE TO /6" H.P. HF2 HM HF4HM2 60,000 O.D. TUE TO H.P. HF4 HM2 60-2HF4HM6 60,000 O.D. TUE TO H.P. HF4 HM6 60-2HF4HM 60,000 O.D. TUE TO /6" H.P. HF4 HM HF6HM2 60,000 O.D. TUE TO H.P. HF6 HM2 " 60-2HF6HM4 60,000 O.D. TUE TO H.P. HF6 HM4 " 60-2HF6HM 60,000 O.D. TUE TO /6" H.P. HF6 HM HFHM4 60,000 /6" O.D. TUE TO H.P. HF HM4 60-2HFHM6 60,000 /6" O.D. TUE TO H.P. HF HM6 High Equipment Company R 5/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.

82 High Equipment Female Medium to Male Medium Hex Catalog No. psi Connections Length Size 20-2LF4LM6 20,000 M.P. FEMLE to M.P. MLE LF4 LM6 20-2LF4LM 20,000 M.P. FEMLE to /6" M.P. MLE LF4 LM 20-2LF6LM4 20,000 M.P. FEMLE to M.P. MLE LF6 LM4 20-2LF6LM 20,000 M.P. FEMLE to /6" M.P. MLE LF6 LM 20-2LFLM4 20,000 /6" M.P. FEMLE to M.P. MLE LF LM4 2 " 20-2LFLM6 20,000 /6" M.P. FEMLE to M.P. MLE LF LM6 2 " 20-2LF2LM4 20,000 M.P. FEMLE to M.P. MLE LF2 LM LF2LM6 20,000 M.P. FEMLE to M.P. MLE LF2 LM LF2LM 20,000 M.P. FEMLE to /6" M.P. MLE LF2 LM LF2LM6 20,000 M.P. FEMLE to " M.P. MLE LF2 LM6 20-2LF4LM2 20,000 M.P. FEMLE to M.P. MLE LF4 LM2 20-2LF6LM2 20,000 M.P. FEMLE to M.P. MLE LF6 LM2 20-2LFLM2 20,000 /6" M.P. FEMLE to M.P. MLE LF LM LF6LM4 20,000 " M.P. FEMLE to M.P. MLE LF6-0 LM LF6LM6 20,000 " M.P. FEMLE to M.P. MLE LF6-0 LM LF6LM 20,000 " M.P. FEMLE to /6" M.P. MLE LF6-0 LM " 20-2LF6LM2 20,000 " M.P. FEMLE to M.P. MLE LF6-0 LM2 20-2LF4LM6 20,000 M.P. FEMLE to " M.P. MLE LF4 LM6 " " 20-2LF6LM6 20,000 M.P. FEMLE to " M.P. MLE LF6 LM6 " 20-2LFLM6 20,000 /6" M.P. FEMLE to " M.P. MLE LF LM6 " Female Medium to Male High Hex Catalog No. psi Connections Length Size 20-2LF4HM4 20,000 M.P. FEMLE to H.P. MLE LF4 HM4 20-2LF4HM6 20,000 M.P. FEMLE to H.P. MLE LF4 HM6 20-2LF4HM 20,000 M.P. FEMLE to /6" H.P. MLE LF4 HM LF6HM4 20,000 M.P. FEMLE to H.P. MLE LF6 HM4 20-2LF6HM6 20,000 M.P. FEMLE to H.P. MLE LF6 HM6 20-2LF6HM 20,000 M.P. FEMLE to /6" H.P. MLE LF6 HM LFHM4 20,000 /6" M.P. FEMLE to H.P. MLE LF HM4 " 20-2LFHM6 20,000 /6" M.P. FEMLE to H.P. MLE LF HM6 2 " 20-2LFHM 20,000 /6" M.P. FEMLE to /6" H.P. MLE LF HM LF2HM4 20,000 M.P. FEMLE to H.P. MLE LF2 HM LF2HM6 20,000 M.P. FEMLE to H.P. MLE LF2 HM LF2HM 20,000 M.P. FEMLE to /6" H.P. MLE LF2 HM 2 5 * 20-2LF6HM4 20,000 " M.P. FEMLE to H.P. MLE LF6 HM4 2 5 * 20-2LF6HM6 20,000 " M.P. FEMLE to H.P. MLE LF6 HM6 2 * 20-2LF6HM 20,000 " M.P. FEMLE to /6" H.P. MLE LF6 HM * Can be rated to 0,000 psi if used with " O.D. x /6" I.D. tubing. 8.0

83 Female to Male dapters Female Medium to Male Pipe Hex Catalog No. psi Connections Length Size 20-2LF4NM 5,000 M.P. FEMLE to NPT MLE LF4 NM /6" 20-2LF4NM 5,000 M.P. FEMLE to NPT MLE LF4 NM LF4NMC 5,000 M.P. FEMLE to NPT MLE LF4 NMC LF4NMD 5,000 M.P. FEMLE to NPT MLE LF4 NMD " 0-2LF4NMF 0,000 M.P. FEMLE to NPT MLE LF4 NMF 0-2LF4NMH 0,000 M.P. FEMLE to " NPT MLE LF4 NMH 20-2LF6NM 5,000 M.P. FEMLE to NPT MLE LF6 NM /6" 20-2LF6NM 5,000 M.P. FEMLE to NPT MLE LF6 NM LF6NMC 5,000 M.P. FEMLE to NPT MLE LF6 NMC LF6NMD 5,000 M.P. FEMLE to NPT MLE LF6 NMD " 0-2LF6NMF 0,000 M.P. FEMLE to NPT MLE LF6 NMF 0-2LF6NMH 0,000 M.P. FEMLE to " NPT MLE LF6 NMH 20-2LFNM 5,000 /6" M.P. FEMLE to NPT MLE LF NM " 20-2LFNM 5,000 /6" M.P. FEMLE to NPT MLE LF NM " 20-2LFNMC 5,000 /6" M.P. FEMLE to NPT MLE LF NMC " 20-2LFNMD 5,000 /6" M.P. FEMLE to NPT MLE LF NMD " 0-2LFNMF 0,000 /6" M.P. FEMLE to NPT MLE LF NMF 0-2LFNMH 0,000 /6" M.P. FEMLE to " NPT MLE LF NMH 20-2LF2NM 5,000 M.P. FEMLE to NPT MLE LF2 NM LF2NM 5,000 M.P. FEMLE to NPT MLE LF2 NM LF2NMC 5,000 M.P. FEMLE to NPT MLE LF2 NMC LF2NMD 5,000 M.P. FEMLE to NPT MLE LF2 NMD 2 0-2LF2NMF 0,000 M.P. FEMLE to NPT MLE LF2 NMF 2 0-2LF2NMH 0,000 M.P. FEMLE to " NPT MLE LF2 NMH LF6NM 5,000 " M.P. FEMLE to NPT MLE LF6-0 NM LF6NM 5,000 " M.P. FEMLE to NPT MLE LF6-0 NM LF6NMC 5,000 " M.P. FEMLE to NPT MLE LF6-0 NMC LF6NMD 5,000 " M.P. FEMLE to NPT MLE LF6-0 NMD 2 0-2LF6NMF 0,000 " M.P. FEMLE to NPT MLE LF6-0 NMF 2 0-2LF6NMH 0,000 " M.P. FEMLE to " NPT MLE LF6-0 NMH 2 High Equipment Company R4 / 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.

84 High Equipment Female Pipe to Male High Hex Catalog No. psi Connections Length Size 0-2NFHM2 5,000 NPT TO H.P. MLE NF HM NFHM2 5,000 NPT TO H.P. MLE NF HM NFCHM2 5,000 NPT TO H.P. MLE NFC HM2 " 0-2NFHM4 5,000 NPT TO H.P. MLE NF HM NFHM4 5,000 NPT TO H.P. MLE NF HM4 0-2NFCHM4 5,000 NPT TO H.P. MLE NFC HM4 " 0-2NFDHM4 5,000 NPT TO H.P. MLE NFD HM NFHM6 5,000 NPT TO H.P. MLE NF HM NFHM6 5,000 NPT TO H.P. MLE NF HM6 0-2NFCHM6 5,000 NPT TO H.P. MLE NFC HM6 " 0-2NFDHM6 5,000 NPT TO H.P. MLE NFD HM NFFHM6 0,000 NPT TO H.P. MLE NFF HM NFHM 5,000 NPT TO /6" H.P. MLE NF HM 2 0-2NFHM 5,000 NPT TO /6" H.P. MLE NF HM 2 0-2NFCHM 5,000 NPT TO /6" H.P. MLE NFC HM 2 0-2NFDHM 5,000 NPT TO /6" H.P. MLE NFD HM 2 0-2NFFHM 0,000 NPT TO /6" H.P. MLE NFF HM 2 0-2NFHHM 0,000 " NPT TO /6" H.P. MLE NFH HM Female High to Male Medium Hex Catalog No. psi Connections Length Size 20-2HF4LM4 20,000 H.P. FEMLE to M.P. MLE HF4 LM4 20-2HF4LM6 20,000 H.P. FEMLE to M.P. MLE HF4 LM6 20-2HF4LM 20,000 H.P. FEMLE to /6" M.P. MLE HF4 LM 20-2HF6LM4 20,000 H.P. FEMLE to M.P. MLE HF6 LM4 " 20-2HF6LM6 20,000 H.P. FEMLE to M.P. MLE HF6 LM6 " 20-2HF6LM 20,000 H.P. FEMLE to /6" M.P. MLE HF6 LM " 20-2HFLM4 20,000 /6" H.P. FEMLE to M.P. MLE HF LM HFLM6 20,000 /6" H.P. FEMLE to M.P. MLE HF LM HFLM 20,000 /6" H.P. FEMLE to /6" M.P. MLE HF LM HF4LM2 20,000 H.P. FEMLE to M.P. MLE HF4 LM HF6LM2 20,000 H.P. FEMLE to M.P. MLE HF6 LM HFLM2 20,000 /6" H.P. FEMLE to M.P. MLE HF LM HF4LM6 20,000 H.P. FEMLE to " M.P. MLE HF4 LM6 " " 20-2HF6LM6 20,000 H.P. FEMLE to " M.P. MLE HF6 LM6 " 20-2HFLM6 20,000 /6" H.P. FEMLE to " M.P. MLE HF LM HF4LM6 20,000 H.P. FEMLE to " M.P. MLE HF4 LM6-0 " " 20-2HF6LM6 20,000 H.P. FEMLE to " M.P. MLE HF6 LM6-0 " 20-2HFLM6 20,000 /6" H.P. FEMLE to " M.P. MLE HF LM R4 5/0

85 Female to Male dapters Female High to Male Pipe Hex Catalog No. psi Connections Length Size 0-2HF2NM 5,000 H.P. TO NPT MLE HF2 NM 5 0-2HF2NM 5,000 H.P. TO NPT MLE HF2 NM 5 0-2HF2NMC 5,000 H.P. TO NPT MLE HF2 NMC 0-2HF2NMD 5,000 H.P. TO NPT MLE HF2 NMD " 0-2HF2NMF 0,000 H.P. TO NPT MLE HF2 NMF 0-2HF2NMH 0,000 H.P. TO " NPT MLE HF2 NMH 0-2HF4NM 5,000 H.P. TO NPT MLE HF4 NM 0-2HF4NM 5,000 H.P. TO NPT MLE HF4 NM 0-2HF4NMC 5,000 H.P. TO NPT MLE HF4 NMC 0-2HF4NMD 5,000 H.P. TO NPT MLE HF4 NMD " 0-2HF4NMF 0,000 H.P. TO NPT MLE HF4 NMF 0-2HF4NMH 0,000 H.P. TO " NPT MLE HF4 NMH 5 0-2HF6NM 5,000 H.P. TO NPT MLE HF6 NM " 0-2HF6NM 5,000 H.P. TO NPT MLE HF6 NM 5 " 0-2HF6NMC 5,000 H.P. TO NPT MLE HF6 NMC 5 " 0-2HF6NMD 5,000 H.P. TO NPT MLE HF6 NMD " 0-2HF6NMF 0,000 H.P. TO NPT MLE HF6 NMF 0-2HF6NMH 0,000 H.P. TO " NPT MLE HF6 NMH 0-2HFNM 5,000 /6" H.P. TO NPT MLE HF NM 0-2HFNM 5,000 /6" H.P. TO NPT MLE HF NM 5 0-2HFNMC 5,000 /6" H.P. TO NPT MLE HF NMC 0-2HFNMD 5,000 /6" H.P. TO NPT MLE HF NMD 0-2HFNMF 0,000 /6" H.P. TO NPT MLE HF NMF 0-2HFNMH 0,000 /6" H.P. TO " NPT MLE HF NMH Female Pipe to Male Taper Seal Hex Catalog No. psi Connections Length Size 5-2NFM2 5,000 FNPT TO MLE T.S. NF M NFM2 5,000 FNPT TO MLE T.S. NF M NFCM2 5,000 FNPT TO MLE T.S. NFC M2 " 0-2NFM4 0,000 FNPT TO MLE T.S. NF M4 0-2NFM4 0,000 FNPT TO MLE T.S. NF M4 " 0-2NFCM4 0,000 FNPT TO MLE T.S. NFC M4 " 0-2NFDM4 0,000 FNPT TO MLE T.S. NFD M NFM6 0,000 FNPT TO MLE T.S. NF M6 " 0-2NFM6 0,000 FNPT TO MLE T.S. NF M6 " 0-2NFCM6 0,000 FNPT TO MLE T.S. NFC M6 " 0-2NFDM6 0,000 FNPT TO MLE T.S. NFD M6 2 High Equipment Company R 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.

86 High Equipment Female Pipe to Male Medium Hex Catalog No. psi Connections Length Size 20-2NFLM4 5,000 N.P.T. FEMLE to M.P. MLE NF LM4 20-2NFLM4 5,000 N.P.T. FEMLE to M.P. MLE NF LM4 20-2NFCLM4 5,000 N.P.T. FEMLE to M.P. MLE NFC LM4 " 20-2NFDLM4 5,000 N.P.T. FEMLE to M.P. MLE NFD LM NFFLM4 0,000 N.P.T. FEMLE to M.P. MLE NFF LM NFLM6 5,000 N.P.T. FEMLE to M.P. MLE NF LM6 20-2NFLM6 5,000 N.P.T. FEMLE to M.P. MLE NF LM6 20-2NFCLM6 5,000 N.P.T. FEMLE to M.P. MLE NFC LM6 2 " 20-2NFDLM6 5,000 N.P.T. FEMLE to M.P. MLE NFD LM NFFLM6 0,000 N.P.T. FEMLE to M.P. MLE NFF LM NFHLM6 0,000 " N.P.T. FEMLE to M.P. MLE NFH LM NFLM 5,000 N.P.T. FEMLE to /6" M.P. MLE NF LM 20-2NFLM 5,000 N.P.T. FEMLE to /6" M.P. MLE NF LM 20-2NFCLM 5,000 N.P.T. FEMLE to /6" M.P. MLE NFC LM 2 " 20-2NFDLM 5,000 N.P.T. FEMLE to /6" M.P. MLE NFD LM 2 0-2NFFLM 0,000 N.P.T. FEMLE to /6" M.P. MLE NFF LM NFHLM 0,000 " N.P.T. FEMLE to /6" M.P. MLE NFH LM " 20-2NFLM2 5,000 N.P.T. FEMLE to M.P. MLE NF LM2 20-2NFLM2 5,000 N.P.T. FEMLE to M.P. MLE NF LM2 20-2NFCLM2 5,000 N.P.T. FEMLE to M.P. MLE NFC LM2 20-2NFDLM2 5,000 N.P.T. FEMLE to M.P. MLE NFD LM NFFLM2 0,000 N.P.T. FEMLE to M.P. MLE NFF LM NFHLM2 0,000 " N.P.T. FEMLE to M.P. MLE NFH LM2 " 20-2NFLM6 5,000 N.P.T. FEMLE to " M.P. MLE NF LM6 " " 20-2NFLM6 5,000 N.P.T. FEMLE to " M.P. MLE NF LM6 " " 20-2NFCLM6 5,000 N.P.T. FEMLE to " M.P. MLE NFC LM6 " " 20-2NFDLM6 5,000 N.P.T. FEMLE to " M.P. MLE NFD LM6 0-2NFFLM6 0,000 N.P.T. FEMLE to " M.P. MLE NFF LM NFHLM6 0,000 " N.P.T. FEMLE to " M.P. MLE NFH LM R 2/00

87 Male to Male dapters dapters: Male to Male Male to Male dapters are available in the most commonly used sizes as listed below. These adapters permit the user to convert female connections to male connections, and are especially useful in confined installations or where rigidity is required. Standard material is high tensile Type 6 stainless steel. Male Taper Seal to Male Taper Seal Hex Catalog No. psi Connections Length Size 5-2MM 5,000 /6" T.S. to /6" T.S. M M 5-2M2M2 5,000 T.S. to T.S. M2 M M2M4 0,000 T.S. to T.S. M2 M4 0-2M4M4 0,000 T.S. to T.S. M4 M M4M6 0,000 T.S. to T.S. M4 M M6M6 0,000 T.S. to T.S. M6 M6 2 Male Taper Seal to Male Medium Hex Catalog No. psi Connections Length Size 0-2M4LM4 0,000 T.S. to M.P. M4 LM M4LM6 0,000 T.S. to M.P. M4 LM6 2 /6" 0-2M4LM 0,000 T.S. to /6" M.P. M4 LM 2 0-2M6LM4 0,000 T.S. to M.P. M6 LM M6LM6 0,000 T.S. to M.P. M6 LM6 2 /6" 0-2M6LM 0,000 T.S. to /6" M.P. M6 LM 2 5-2M2LM4 5,000 T.S. to M.P. M2 LM4 5-2M2LM6 5,000 T.S. to M.P. M2 LM M2LM 5,000 T.S. to /6" M.P. M2 LM 2 Male Taper Seal to Male Pipe Hex Catalog No. psi Connections Length Size 5-2MNM 5,000 /6" T.S. to NPT MLE M NM /6" 5-2MNM 5,000 /6" T.S. to NPT MLE M NM /6" 5 5-2M2NM 5,000 T.S. to NPT MLE M2 NM 5 5-2M2NM 5,000 T.S. to NPT MLE M2 NM 5 5-2M4NM 5,000 T.S. to NPT MLE M4 NM High Equipment Company R2 0/2 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.5

88 High Equipment Male Taper Seal to Male High Hex Catalog No. psi Connections Length Size 5-2M2HM2 5,000 T.S. to H.P. M2 HM2 /6" 5 5-2M2HM4 5,000 T.S. to H.P. M2 HM M4HM4 0,000 T.S. to H.P. M4 HM4 Male Medium to Male High Hex Catalog No. psi Connections Length Size 20-2LM4HM2 20,000 M.P. to H.P. LM4 HM LM4HM 20,000 M.P. to /6" H.P. LM4 HM LMHM4 20,000 /6" M.P. to H.P. LM HM LMHM 20,000 /6" M.P. to /6" H.P. LM HM LM6HM4 20,000 M.P. to H.P. LM6 HM LM6HM 20,000 M.P. to /6" H.P. LM6 HM 2 Male Medium to Male Pipe (NPT) Hex Catalog No. psi Connections Length Size 20-2LM4NM 5,000 M.P. to NPT MLE LM4 NM LM4NMD 5,000 M.P. to NPT MLE LM4 NMD LM6NM 5,000 M.P. to NPT MLE LM6 NM 2 /6" 20-2LM6NMC 5,000 M.P. to NPT MLE LM6 NMC 2 /6" 20-2LM6NMD 5,000 M.P. to NPT MLE LM6 NMD 2 /6" 20-2LMNM 5,000 /6" M.P. to NPT MLE LM NM LMNM 5,000 /6" M.P. to NPT MLE LM NM LMNMC 5,000 /6" M.P. to NPT MLE LM NMC LMNMD 5,000 /6" M.P. to NPT MLE LM NMD 2 0-2LMNMF 0,000 /6" M.P. to NPT MLE LM NMF LMNMH 0,000 /6" M.P. to " NPT MLE LM NMH LM2NM 5,000 M.P. to NPT MLE LM2 NM LM2NM 5,000 M.P. to NPT MLE LM2 NM LM2NMC 5,000 M.P. to NPT MLE LM2 NMC LM2NMD 5,000 M.P. to NPT MLE LM2 NMD LM2NMF 0,000 M.P. to NPT MLE LM2 NMF 2 0-2LM2NMH 0,000 M.P. to " NPT MLE LM2 NMH 20-2LM6NM 5,000 " M.P. to NPT MLE LM6 NM 5 " 20-2LM6NM 5,000 " M.P. to NPT MLE LM6 NM " 20-2LM6NMC 5,000 " M.P. to NPT MLE LM6 NMC " 20-2LM6NMD 5,000 " M.P. to NPT MLE LM6 NMD " 0-2LM6NMF 0,000 " M.P. to NPT MLE LM6 NMF 0-2LM6NMH 0,000 " M.P. to " NPT MLE LM6 NMH R4 5/0

89 Male to Male dapters Male Medium to Male Medium Hex Catalog No. psi Connections Length Size 20-2LM4LM4 20,000 M.P. to M.P. LM4 LM LM4LM6 20,000 M.P. to M.P. LM4 LM LM6LM6 20,000 M.P. to M.P. LM6 LM LM6LM 20,000 M.P. to /6" M.P. LM6 LM LMLM 20,000 /6" M.P. to /6" M.P. LM LM 2 5 /8 20-2LM4LM2 20,000 M.P. to M.P. LM4 LM LM6LM2 20,000 M.P. to M.P. LM6 LM LMLM2 20,000 /6" M.P. to M.P. LM LM LM4LM6 20,000 M.P. to " M.P. LM4 LM6 5 " 20-2LM6LM6 20,000 M.P. to " M.P. LM6 LM6 " 20-2LMLM6 20,000 /6" M.P. to " M.P. LM LM6 4" " 20-2LM2LM2 20,000 M.P. to M.P. LM2 LM2 " 20-2LM2LM6 20,000 M.P. to " M.P. LM2 LM6 Male High to Male Pipe (NPT) Hex Catalog No. psi Connections Length Size 0-2HM2NM 5,000 H.P. to NPT MLE HM2 NM 5 0-2HM2NM 5,000 H.P. to NPT MLE HM2 NM 5 0-2HM4NM 5,000 H.P. to NPT MLE HM4 NM 5 0-2HM4NM 5,000 H.P. to NPT MLE HM4 NM 5 0-2HM4NMC 5,000 H.P. to NPT MLE HM4 NMC 0-2HM4NMD 5,000 H.P. to NPT MLE HM4 NMD 2 0-2HM4NMF 0,000 H.P. to NPT MLE HM4 NMF 2 0-2HM6NM 5,000 H.P. to NPT MLE HM6 NM 2 0-2HM6NMC 5,000 H.P. to NPT MLE HM6 NMC 2 0-2HMNM 5,000 /6" H.P. to NPT MLE HM NM 2 0-2HMNMC 5,000 /6" H.P. to NPT MLE HM NMC 2 0-2HMNMD 5,000 /6" H.P. to NPT MLE HM NMD 2 0-2HMNMF 0,000 /6" H.P. to NPT MLE HM NMF HMNMH 0,000 /6" H.P. to " NPT MLE HM NMH 2 Male Pipe to Male Pipe Hex Catalog No. psi Connections Length Size 5-2NMNM 5,000 NPT MLE to NPT MLE NM NM 5 5-2NMNMC 5,000 NPT MLE to NPT MLE NM NM 5-2NMCNMC 5,000 NPT MLE to NPT MLE NMC NMC 5-2NMDNMD 5,000 NPT MLE to NPT MLE NMD NMD 2 " High Equipment Company R / 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.

90 High Equipment Male High to Male Medium Hex Catalog No. psi Connections Length Size 20-2HM4LM2 20,000 H.P. to M.P. HM4 LM HM6LM2 20,000 H.P. to M.P. HM6 LM HMLM2 20,000 /6" H.P. to M.P. HM LM2 " 20-2HM4LM6 20,000 H.P. to " M.P. HM4 LM6 5 " 20-2HM6LM6 20,000 H.P. to " M.P. HM6 LM6 4" " 20-2HMLM6 20,000 /6" H.P. to " M.P. HM LM6 4" Male High to Male High Hex Catalog No. psi Connections Length Size 60-2HM2HM2 60,000 H.P. to H.P. HM2 HM2 60-2HM2HM4 60,000 H.P. to H.P. HM2 HM HM4HM4 60,000 H.P. to H.P. HM4 HM4 /6" HM4HM6 60,000 H.P. to H.P. HM4 HM6 2 /6" 60-2HM4HM 60,000 H.P. to /6" H.P. HM4 HM HM6HM6 60,000 H.P. to H.P. HM6 HM HM6HM 60,000 H.P. to /6" H.P. HM6 HM HMHM 60,000 /6" H.P. to /6" H.P. HM HM HM4HM6 0,000 H.P. to " M.P. HM4 HM6 5 " 0-2HM6HM6 0,000 H.P. to " M.P. HM6 HM6 4" " 0-2HMHM6 0,000 /6" H.P. to " M.P. HM HM6 4" 8.8 R2 2/

91 NPT Fittings complete line of couplings and adapters with NPT threaded connections are now available. These fittings feature 6 cold-worked stainless steel construction, with other materials available. HiP maintains an inventory of these fittings for quick ship requirements. NPT Fittings NPT Straight Couplings Hex Catalog No. psi Connections Length Size 5-2NF 5,000 FEMLE NPT x FEMLE NPT NF NF 5-2NF 5,000 FEMLE NPT x FEMLE NPT NF NF " 5-2NFC 5,000 FEMLE NPT x FEMLE NPT NFC NFC " 5-2NFD 5,000 FEMLE NPT x FEMLE NPT NFD NFD 0-2NFF 0,000 FEMLE NPT x FEMLE NPT NFF NFF 2 0-2NFH 0,000 " FEMLE NPT x " FEMLE NPT NFH NFH 2 NPT Reducer Couplings Hex Catalog No. psi Connections Length Size 5-2NFNFC 5,000 FEMLE NPT x FEMLE NPT NF NFC " 5-2NFNFD 5,000 FEMLE NPT x FEMLE NPT NF NFD 5-2NFCNFD 5,000 FEMLE NPT x FEMLE NPT NFC NFD dapters: Male to Male NPT Hex Catalog No. psi Connections Length Size 5-2NMNM 5,000 MLE NPT x MLE NPT NM NM 5-2NMNM 5,000 MLE NPT x MLE NPT NM NM 5 5-2NMCNMC 5,000 MLE NPT x MLE NPT NMC NMC 5-2NMDNMD 5,000 MLE NPT x MLE NPT NMD NMD 2 " 0-2NMFNMF 0,000 MLE NPT x MLE NPT NMF NMF 2 0-2NMHNMH 0,000 " MLE NPT x " MLE NPT NMH NMH NMNMC 5,000 MLE NPT x MLE NPT NM NMC 5-2NMNMD 5,000 MLE NPT x MLE NPT NM NMD 5-2NMCNMD 5,000 MLE NPT x MLE NPT NMC NMD " High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

92 High Equipment dapters: Female to Male NPT Hex Catalog No. psi Connections Length Size 5-2NFNM 5,000 FEMLE NPT x MLE NPT NF NM 5-2NFNM 5,000 FEMLE NPT x MLE NPT NF NM 5-2NFNMC 5,000 FEMLE NPT x MLE NPT NF NMC 5 5-2NFNMD 5,000 FEMLE NPT x MLE NPT NF NMD 5-2NFNM 5,000 FEMLE NPT x MLE NPT NF NM 5 5-2NFNM 5,000 FEMLE NPT x MLE NPT NF NM 5 " 5-2NFNMC 5,000 FEMLE NPT x MLE NPT NF NMC 5 " 5-2NFNMD 5,000 FEMLE NPT x MLE NPT NF NMD " 5-2NFCNM 5,000 FEMLE NPT x MLE NPT NFC NM " 5-2NFCNMD 5,000 FEMLE NPT x MLE NPT NFC NMD " 5-2NFDNM 5,000 FEMLE NPT x MLE NPT NFD NM 5-2NFDNM 5,000 FEMLE NPT x MLE NPT NFD NM 5-2NFDNMC 5,000 FEMLE NPT x MLE NPT NFD NMC 5-2NFDNMD 5,000 FEMLE NPT x MLE NPT NFD NMD 2 0-2NFFNMD 0,000 FEMLE NPT x MLE NPT NFF NMD 2 0-2NFFNMH 0,000 FEMLE NPT x " MLE NPT NFF NMH 2 0-2NFHNMD 0,000 " FEMLE NPT x MLE NPT NFH NMD 2 0-2NFHNMF 0,000 " FEMLE NPT x MLE NPT NFH NMF

93 Hose Fittings Hose Fittings We now offer a line of hose adapters designed to easily and safely mate with standard type M fittings. Our new hose adapters are rated to the maximum working pressure of the hose or hose-end connection. Our hose fittings are constructed of 6 cold-worked stainless steel with other materials available. HiP maintains an inventory of these fittings for quick ship requirements. High to Hose Hex Catalog No. psi Connections Length Size 40-2HM4H 40,000 H.P. x /6" HOSE 0-2HM4H2 0,000 H.P. x HOSE 26-2HM4H6 26,000 H.P. x " HOSE 40-2HM6H 40,000 H.P. x /6" HOSE 0-2HM6H2 0,000 H.P. x HOSE 26-2HM6H6 26,000 H.P. x " HOSE 40-2HMH 40,000 /6" H.P. x /6" HOSE 0-2HMH2 0,000 /6" H.P. x HOSE 26-2HMH6 26,000 /6" H.P. x " HOSE HM4 HM4 HM4 HM6 HM6 HM6 HM HM HM /6" " /6" " /6" " Medium to Hose Hex Catalog No. psi Connections Length Size 20-2LM4H 20,000 M.P. x /6" HOSE LM4 /6" 20-2LM4H2 20,000 M.P. x HOSE LM4 " 20-2LM4H6 20,000 M.P. x " HOSE LM4 " LM6H 20,000 M.P. x /6" HOSE LM6 /6" 20-2LM6H2 20,000 M.P. x HOSE LM6 " 20-2LM6H6 20,000 M.P. x " HOSE LM6 " LMH 20,000 /6" M.P. x /6" HOSE LM /6" 2 " 20-2LMH2 20,000 /6" M.P. x HOSE LM 2 " 20-2LMH6 20,000 /6" M.P. x " HOSE LM " LM2H 20,000 M.P. x /6" HOSE LM2 /6" LM2H2 20,000 M.P. x HOSE LM LM2H6 20,000 M.P. x " HOSE LM2 " LM2H2 20,000 M.P. x 5 /6" HOSE LM2 5 /6" LM6H 20,000 " M.P. x /6" HOSE LM6 /6" LM6H2 20,000 " M.P. x HOSE LM6 20-2LM6H6 20,000 " M.P. x " HOSE LM6 " 20-2LM6H2 20,000 " M.P. x 5 /6" HOSE LM6 5 /6" 4" / 2 " High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

94 High Equipment NPT to Hose Hex Catalog No. psi Connections Length Size 5-2NMH 5,000 NPT MLE x /6" HOSE NM /6" NMH2 5,000 NPT MLE x HOSE NM 5-2NMH6 5,000 NPT MLE x " HOSE NM " " 5-2NMCH 5,000 NPT MLE x /6" HOSE NMC /6" 5 5-2NMCH2 5,000 NPT MLE x HOSE NMC 5-2NMCH6 5,000 NPT MLE x " HOSE NMC " " 5-2NMDH 5,000 NPT MLE x /6" HOSE NMD /6" 5-2NMDH2 5,000 NPT MLE x HOSE NMD 5-2NMDH6 5,000 NPT MLE x " HOSE NMD " " 0-2NMFH2 0,000 NPT MLE x HOSE NMF 0-2NMFH6 0,000 NPT MLE x " HOSE NMF " 0-2NMHH6 0,000 " NPT MLE x " HOSE NMH " 2 Hose to Hose Hex Catalog No. psi Connections Length Size 26-2HH 26,000 /6" HOSE x /6" HOSE /6" /6" 26-2HH2 26,000 /6" HOSE x HOSE /6" HH6 26,000 /6" HOSE x " HOSE /6" " 26-2H2H2 26,000 HOSE x HOSE 26-2H2H6 26,000 HOSE x " HOSE " 26-2H6H6 26,000 " HOSE x " HOSE " " 8.8.4

95 Straight Couplings Reducer Couplings complete range of couplings is offered for flexibility in going from tube to tube and from tube to pipe. ll standard coupling bodies are made from high tensile 6 stainless steel. Standard tubing glands and collars (sleeves) are provided with adapters unless otherwise specified. Taper Seal Straight Couplings Hex Catalog No. psi Connections Length Size 5-2F 5,000 /6" O.D. TUIN F F " 5-2F2 5,000 O.D. TUIN F2 F2 0-2F4 0,000 O.D. TUIN F4 F4 " 0-2F6 0,000 O.D. TUIN F6 F6 " Female Taper Seal to Female NPT Hex Catalog No. psi Connections Length Size 5-2FNF 5,000 /6" O.D. TUE TO NPT F NF 5 5-2FNF 5,000 /6" O.D. TUE TO NPT F NF 5-2FNFC 5,000 /6" O.D. TUE TO NPT F NFC " 5-2FNFD 5,000 /6" O.D. TUE TO NPT F NFD 5-2F2NF 5,000 O.D. TUE TO NPT F2 NF 5 5-2F2NF 5,000 O.D. TUE TO NPT F2 NF 5-2F2NFC 5,000 O.D. TUE TO NPT F2 NFC " 5-2F2NFD 5,000 O.D. TUE TO NPT F2 NFD 0-2F4NF 0,000 O.D. TUE TO NPT F4 NF 5 " 0-2F4NF 0,000 O.D. TUE TO NPT F4 NF " 0-2F4NFC 0,000 O.D. TUE TO NPT F4 NFC " 0-2F4NFD 0,000 O.D. TUE TO NPT F4 NFD 0-2F4NFF 0,000 O.D. TUE TO NPT F4 NFF 2 0-2F4NFH 0,000 O.D. TUE TO " NPT F4 NFH F6NF 0,000 O.D. TUE TO NPT F6 NF 5 " 0-2F6NF 0,000 O.D. TUE TO NPT F6 NF " 0-2F6NFC 0,000 O.D. TUE TO NPT F6 NFC " 0-2F6NFD 0,000 O.D. TUE TO NPT F6 NFD 2 0-2F6NFF 0,000 O.D. TUE TO NPT F6 NFF 2 0-2F6NFH 0,000 O.D. TUE TO " NPT F6 NFH 2 5 High Equipment Company R 5/0 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.

96 High Equipment Female Taper Seal to Female Female High Hex Catalog No. psi Connections Length Size 5-2FHF2 5,000 /6" O.D. TUE TO H.P. F HF FHF4 5,000 /6" O.D. TUE TO H.P. F HF4 5-2FHF6 5,000 /6" O.D. TUE TO H.P. F HF6 " 5-2FHF 5,000 /6" O.D. TUE TO /6" H.P. F HF 2 5-2F2HF2 5,000 O.D. TUE TO H.P. F2 HF2 5-2F2HF4 5,000 O.D. TUE TO H.P. F2 HF4 5-2F2HF6 5,000 O.D. TUE TO H.P. F2 HF6 " 5-2F2HF 5,000 O.D. TUE TO /6" H.P. F2 HF 2 0-2F4HF2 0,000 O.D. TUE TO H.P. F4 HF2 " 0-2F4HF4 0,000 O.D. TUE TO H.P. F4 HF4 " 0-2F4HF6 0,000 O.D. TUE TO H.P. F4 HF6 " 0-2F4HF 0,000 O.D. TUE TO /6" H.P. F4 HF 2 0-2F6HF2 0,000 O.D. TUE TO H.P. F6 HF2 " 0-2F6HF4 0,000 O.D. TUE TO H.P. F6 HF4 " 0-2F6HF6 0,000 O.D. TUE TO H.P. F6 HF6 " 0-2F6HF 0,000 O.D. TUE TO /6" H.P. F6 HF 2 Taper Seal Reducer Couplings Hex Catalog No. psi Connections Length Size 5-2FF2 5,000 /6" O.D. TO O.D. TUE F F FF4 0,000 /6" O.D. TO O.D. TUE F F4 " 0-2FF6 0,000 /6" O.D. TO O.D. TUE F F6 " 0-2F2F4 0,000 O.D. TO O.D. TUE F2 F4 " 0-2F2F6 0,000 O.D. TO O.D. TUE F2 F6 " 0-2F4F6 0,000 O.D. TO O.D. TUE F4 F6 " Female Medium to Female Medium Hex Catalog No. psi Connections Length Size 20-2LF4LF6 20,000 M.P. to M.P. LF4 LF6 20-2LF4LF 20,000 M.P. to /6" M.P. LF4 LF 2 " 20-2LF6LF 20,000 M.P. to /6" M.P. LF6 LF 2 " 20-2LF4LF2 20,000 M.P. to M.P. LF4 LF LF6LF2 20,000 M.P. to M.P. LF6 LF LFLF2 20,000 /6" M.P. to M.P. LF LF LF4LF6 20,000 M.P. to " M.P. LF4 LF6 20-2LF6LF6 20,000 M.P. to " M.P. LF6 LF6 20-2LFLF6 20,000 /6" M.P. to " M.P. LF LF6 20-2LF2LF6 20,000 M.P. to " M.P. LF2 LF R 2/

97 Couplings Female Medium to Female Pipe Hex Catalog No. psi Connections Length Size 20-2LF4NF 5,000 M.P. to NPT FEMLE LF4 NF LF4NF 5,000 M.P. to NPT FEMLE LF4 NF LF4NFC 5,000 M.P. to NPT FEMLE LF4 NFC " 20-2LF4NFD 5,000 M.P. to NPT FEMLE LF4 NFD 0-2LF4NFF 0,000 M.P. to NPT FEMLE LF4 NFF 2 0-2LF4NFH 0,000 M.P. to " NPT FEMLE LF4 NFH LF6NF 5,000 M.P. to NPT FEMLE LF6 NF 20-2LF6NF 5,000 M.P. to NPT FEMLE LF6 NF 20-2LF6NFC 5,000 M.P. to NPT FEMLE LF6 NFC 2 " 20-2LF6NFD 5,000 M.P. to NPT FEMLE LF6 NFD 2 0-2LF6NFF 0,000 M.P. to NPT FEMLE LF6 NFIF 2 0-2LF6NFH 0,000 M.P. to " NPT FEMLE LF6 NFH LFNF 5,000 /6" M.P. to NPT FEMLE LF NF 2 " 20-2LFNF 5,000 /6" M.P. to NPT FEMLE LF NF 2 " 20-2LFNFC 5,000 /6" M.P. to NPT FEMLE LF NFC 2 " 20-2LFNFD 5,000 /6" M.P. to NPT FEMLE LF NFD 2 0-2LFNFF 0,000 /6" M.P. to NPT FEMLE LF NFF 2 0-2LFNFH 0,000 /6" M.P. to " NPT FEMLE LF NFH LF2NF 5,000 M.P. to NPT FEMLE LF2 NF LF2NF 5,000 M.P. to NPT FEMLE LF2 NF LF2NFC 5,000 M.P. to NPT FEMLE LF2 NFC LF2NFD 5,000 M.P. to NPT FEMLE LF2 NFD 2 0-2LF2NFF 0,000 M.P. to NPT FEMLE LF2 NFF 2 0-2LF2NFH 0,000 M.P. to " NPT FEMLE LF2 NFH " 20-2LF6NF 5,000 " M.P. to NPT FEMLE LF6 NF " 20-2LF6NF 5,000 " M.P. to NPT FEMLE LF6 NF " 20-2LF6NFC 5,000 " M.P. to NPT FEMLE LF6 NFC " 20-2LF6NFD 5,000 " M.P. to NPT FEMLE LF6 NFD " 0-2LF6NFF 0,000 " M.P. to NPT FEMLE LF6 NFF 0-2LF6NFH 0,000 " M.P. to " NPT FEMLE LF6 NFH Medium Straight Couplings Hex Catalog No. psi Connections Length Size 20-2LF4 20,000 O.D. TUIN LF4 LF4 /6" LF6 20,000 O.D. TUIN LF6 LF6 20-2LF 20,000 /6" O.D. TUIN LF LF 2 " 20-2LF2 20,000 O.D. TUIN LF2 LF LF6 20,000 " O.D. TUIN LF6 LF6 High Equipment Company R4 5/0 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.2

98 High Equipment Female Medium to Female High Hex Catalog No. psi Connections Length Size 20-2LF4HF4 20,000 M.P. to H.P. LF4 HF LF4HF6 20,000 M.P. to H.P. LF4 HF6 " 20-2LF4HF 20,000 M.P. to /6" H.P. LF4 HF LF6HF4 20,000 M.P. to H.P. LF6 HF4 20-2LF6HF6 20,000 M.P. to H.P. LF6 HF6 " 20-2LF6HF 20,000 M.P. to /6" H.P. LF6 HF LFHF4 20,000 /6" M.P. to H.P. LF HF4 2 " 20-2LFHF6 20,000 /6" M.P. to H.P. LF HF6 2 " 20-2LFHF 20,000 /6" M.P. to /6" H.P. LF HF LF2HF4 20,000 M.P. to H.P. LF2 HF LF2HF6 20,000 M.P. to H.P. LF2 HF LF2HF 20,000 M.P. to /6" H.P. LF2 HF 2 * 20-2HF6HF4 20,000 " M.P. to H.P HF6 HF4 * 20-2HF6HF6 20,000 " M.P. to H.P HF6 HF6 * 20-2HF6HF 20,000 " M.P. to /6" H.P. HF6 HF * Can be rated to 0,000 psi if used with " O.D. x /6" I.D. tubing. High Straight Couplings Hex Catalog No. psi Connections Length Size 60-2HF2 60,000 O.D. TUIN HF2 HF2 60-2HF4 60,000 O.D. TUIN HF4 HF4 " 60-2HF6 60,000 O.D. TUIN HF6 HF6 " 60-2HF 60,000 /6" O.D. TUIN HF HF 2 0-2HF6 0,000 " O.D. TUIN HF6 HF6 High Reducer Couplings Hex Catalog No. psi Connections Length Size 60-2HF2HF4 60,000 O.D. TO O.D. TUE HF2 HF4 60-2HF2HF6 60,000 O.D. TO O.D. TUE HF2 HF6 5 " 60-2HF2HF 60,000 /6" O.D. TO /6" O.D. TUE HF2 HF 60-2HF4HF6 60,000 O.D. TO O.D. TUE HF4 HF6 5 " 60-2HF4HF 60,000 O.D. TO /6" O.D. TUE HF4 HF 60-2HF6HF 60,000 O.D. TO /6" O.D. TUE HF6 HF 8.22 R2 6/

99 Couplings Female High to Female NPT Pipe Hex Catalog No. psi Connections Length Size 0-2HF2NF 5,000 O.D. TUE TO NPT HF2 NF 0-2HF2NF 5,000 O.D. TUE TO NPT HF2 NF 0-2HF2NFC 5,000 O.D. TUE TO NPT HF2 NFC " 0-2HF2NFD 5,000 O.D. TUE TO NPT HF2 NFD 0-2HF2NFF 0,000 O.D. TUE TO NPT HF2 NFF 0-2HF2NFH 0,000 O.D. TUE TO " NPT HF2 NFH 2 0-2HF4NF 5,000 O.D. TUE TO NPT HF4 NF " 0-2HF4NF 5,000 O.D. TUE TO NPT HF4 NF " 0-2HF4NFC 5,000 O.D. TUE TO NPT HF4 NFC " 0-2HF4NFD 5,000 O.D. TUE TO NPT HF4 NFD 0-2HF4NFF 0,000 O.D. TUE TO NPT HF4 NFF 0-2HF4NFH 0,000 O.D. TUE TO " NPT HF4 NFH 2 0-2HF6NF 5,000 O.D. TUE TO NPT HF6 NF " 0-2HF6NF 5,000 O.D. TUE TO NPT HF6 NF " 0-2HF6NFC 5,000 O.D. TUE TO NPT HF6 NFC " 0-2HF6NFD 5,000 O.D. TUE TO NPT HF6 NFD 0-2HF6NFF 0,000 O.D. TUE TO NPT HF6 NFF 2 0-2HF6NFH 0,000 O.D. TUE TO " NPT HF6 NFH HFNF 5,000 /6" O.D. TUE TO NPT HF NF 2 0-2HFNF 5,000 /6" O.D. TUE TO NPT HF NF 2 0-2HFNFC 5,000 /6" O.D. TUE TO NPT HF NFC 2 0-2HFNFD 5,000 /6" O.D. TUE TO NPT HF NFD 2 0-2HFNFF 0,000 /6" O.D. TUE TO NPT HF NFF 2 0-2HFNFH 0,000 /6" O.D. TUE TO " NPT HF NFH 2 5 High Equipment offers an extensive selection of couplings and adapters to meet virtually every requirement. High Equipment Company R4 5/0 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 8.2

100 High Equipment Thermocouple dapters The /6" O.D. and O.D. tubing sizes of the Taper Seal connections are ideally suited for use with thermocouples for pressures up to 5,000 psi. These connectors do not bite into the outer wall of the thermocouple, but rather clamp onto the tubing (or thermocouple) similar to a machine collet. thread lubricant is recommended on the gland nut when initially making up the connection, but such lubrication can later be removed if desired. Material is high tensile 6 stainless steel. Standard glands and sleeves are provided unless otherwise specified. dapters for /6 " TCs Hex Catalog No. psi Male End of dapter Length Size 5-2FM2-T 5,000 TPER SEL 0-2FM4-T 0,000 TPER SEL 0-2FM6-T 0,000 TPER SEL 5-2FHM2-T 5,000 HIH PRESSURE 5-2FHM4-T 5,000 HIH PRESSURE 5 5-2FHM6-T 5,000 HIH PRESSURE 5-2FHM-T 5,000 /6" HIH PRESSURE 2 5-2FNM-T 5,000 NPT " 5-2FNM-T 5,000 NPT 5 5-2FNMC-T 5,000 NPT 5-2FNMD-T 5,000 NPT " 0-2FNMF-T 0,000 NPT 0-2FNMH-T 0,000 " NPT 5 dapters for /8 " TCs Hex Catalog No. psi Male End of dapter Length Size 0-2F2M4-T 0,000 TPER SEL 0-2F2M6-T 0,000 TPER SEL 5-2F2HM4-T 5,000 HIH PRESSURE 5 5-2F2HM6-T 5,000 HIH PRESSURE 5-2F2HM-T 5,000 /6" HIH PRESSURE 2 5-2F2NM-T 5,000 NPT 5-2F2NM-T 5,000 NPT 5 5-2F2NMC-T 5,000 NPT 5-2F2NMD-T 5,000 NPT " 0-2F2NMF-T 0,000 NPT 0-2F2NMH-T 0,000 " NPT

101 auges Standard pressure gauges as shown are available from stock for immediate delivery. auge models 4P5 through 6P50 are standard with a High O.D. tubing connection (HF4), while models 6P5, 6P00 and 6P50 have a Ultra High O.D. tubing connection (XF6). These coned and threaded connections are machined directly into the bottom inlet of the gauges. dapters for other size connections are available from stock. These gauges have a solid front separating the dial face from the pressure tube in order to provide maximum safety. ourdon tube and socket are 6 S.S. on all gauges. oth styles include a safety blowout back. 5,000 psi to 0,000 psi gauges have laminated safety glass, while the 50,000 psi to 50,000 psi style have a removable polycarbonate plastic front window. auges may be used intermittently to 00 percent of dial reading. ccuracy on 5,000 psi and 0,000 psi models is /2% of full scale reading. ccuracy on 20,000 psi through 0,000 psi models is % of full scale reading. ccuracy on 50,000 psi through 50,000 psi models is /2% of full scale reading. PNEL MOUNTIN: 4P5, 4P0, 6P20, 6P0 D F Standard auges In Stock auge Size Materials Catalog Range Dial No. psi Size raduations Mounting Case 4P5 0-5,000 4" P0 0-0,000 4", P ,000 6" 2,000, Panel 6 S.S. 6P0 0-0,000 6",000, P ,000 6" 5,000 2, P5 0-5,000 6" 0,000 2, Heavy * Surface Duty 6P ,000 6" 0,000 5,000,000 lum. 6P ,000 6" 20,000 0,000,000 * Panel mount kit available. Contact factory. SURFCE MOUNTIN: 6P50, 6P5, 6P00 20 F C C L C L E Dimensions C L D H Dial Size C D E F H 4" 4P5, 4P0 /6" 4 5 /64" 5 /6" 6" 6P20, 6P0 " /6" /6" 6" 6P50, 6P5, 6P00, 6P50 " High Equipment Company R 8/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

102 High Equipment Tooling To ensure safe and leak-free operation of your pressure system, High Equipment Company provides complete installation instructions for the make-up of a coned and threaded connection. In addition to outlining the correct procedures, we offer coning and threading tools and female tubing connection tools. Index Page Reseating Tools Coning Tools Threading Tools Coning & Threading Instructions

103 High Equipment Tooling The coned and threaded tubing ends for the medium, high and ultra high pressure connections may be supplied by any of the following:. Standard length tubing nipples with ends prepared. Maintained in stock ready for shipment. 2. Special length tubing nipples with ends prepared. Specify length required (up to 22 feet long). dd coning and threading charge to tubing price. (While not in stock, special length nipples can be furnished quickly for prompt delivery).. Preparation of tubing ends at your own facility by hand tooling as described in this section. The coning and threading tools are designed for simple yet accurate preparation of tubing ends for the medium, high and ultra high pressure connections. liberal amount of cutting fluid should be used, and a supply is furnished with each order for tooling. Interchangeable spare parts allow easy change over from one size tubing to another on both the coning and threading tools. Note that the reseating tool is not required for tubing preparation. Coning Tool Reseating Tool Coning Tool Handle Collar Set Screw Cap earing ody Cutter Tubing Collet Collet Nut Threading Tool Threading Tool Set Screw uide ushing Housing Handle Die Reseating Tools The reseating tools are available for repairing old or damaged tubing connection seats in valves or fittings. This tool is not required for tubing preparation. Catalog No. RTLF4 RTLF6 RTLF RTHF2 RTHF4 RTHF6 RTHF RTXF4 RTXF6 For Tubing Connection LF4 LF6 LF HF2 HF4 HF6 HF XF4 XF6 Handle uide ushing Cutter.2 R 6/0

104 Coning Tools The coning tool is designed for preparing a cone on the ends of Medium, High and Ultra High tubing. Included angle of the cone is approximately 5 to 5 degrees. The cutter and collet are interchangeable on all of the assemblies (except 2-HF and 2-LF) to permit changing from one size tubing to another. Catalog No. Tubing Size Spare Spare Cutter Collet 2-LF4 2-LF6 2-LF 2-HF2 2-HF4 2-HF6 2-HF 2-XF4 2-XF6 ( O.D. x.0" I.D. ( psi) ( O.D. x.20 I.D. (20,000 psi) ( /6" O.D. x.2 I.D. (20,000 psi) ( O.D. x.020 I.D. (60,000 psi) ( O.D. x.040 I.D. (0,000 psi) ( O.D. x.08 I.D. (60,000 psi) ( O.D. x I.D. (60,000 psi) ( /6" O.D. x /6" I.D. x (60,000 psi) ( O.D. x /6" I.D. (00,000 psi) ( O.D. x /6" I.D. (50,000 psi) 2-LF4L 2-LF6L 2-LFL* 2-HF2L 2-HF4L 2-HF6L 2-HFL* 2-XF4L 2-XF6L 2-LF4P 2-LF6P 2-LFP 2-HF2P 2-HF4P 2-HF6P 2-HFP 2-XF4P 2-XF6P * Not interchangeable Threading Tools The threading tool is designed for preparing a left-hand thread onto Medium, High and Ultra High tubing ends. The threaded die and guide bushings are interchangeable on all of the assemblies (except 2-MHF2) to permit changing from one size tubing to another. Catalog No. Tubing Size Spare Threading Die Spare uide ushing 2-MLF4 O.D. - 28LH 2-MLF4P 2-MLF6 O.D. - 24LH 2-MLF6P 2-MLF 2-MHF2 2-MHF4 2-MHF6 2-MHF 2-MXF4 2-MXF6 * Not interchangeable /6" O.D. O.D. O.D. O.D. /6" O.D. O.D. O.D. /6"- 8LH 2-MLFP - 40LH* 2-MHF2P* - 28LH 2-MHF4P - 24LH 2-MHF6P /6"- 8LH 2-MHFP - 28LH 2-MXF4P - 24LH 2-MXF6P High Equipment Company R2 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

105 High Equipment Coning and Threading Instructions Coning Tubing Ends The coning tool is designed for preparing a cone having an included angle of approximately 5 to 5 degrees on the ends of tubing. Operation is as follows:. Secure coning tool body in suitable vise. You may wish to angle the tool in the vise in order to facilitate access to the collet nut and knurled cap. 2. Cut off tubing to desired length and deburr ends.. Rotate knurled cap clockwise into tool as far as it will go. 4. ack off knurled cap by rotating counterclockwise a number of complete rotations as indicated in the chart below. ( mark on the knurled cap may be useful). Tubing Size ack Off Turns O.D. turns. fter coning the tubing end, loosen the collet nut and remove tubing from the tool. Remove the knurled cap and cutter from the tool in order to clean off the Sulflo compound and steel chips in preparation for the next tube. NOTES:. Steps and 4 (on left) are primarily a help in properly positioning the tubing in the tool. s you gain experience with the tool, you will be able to judge the proper position by sight in order to eliminate these steps.. The O.D. and O.D. tubing sizes are relatively easy to cone. The O.D. size is delicate (be especially careful not to force the cutter). The /6" O.D. size requires the most amount of firmness in the cutting. C. s with other tools, it is not uncommon for a collet to stick even after the collet nut has been released. Should this occur, simply tap the side of the collet nut firmly with the wrench to release the collet. O.D. 4 /2 turns O.D. 4 /2 turns /6" O.D. 8 turns 5. Insert tubing thru collet nut and collet until tubing stops up against inside cutter. 6. Tighten collet nut to secure tubing into position.. Turn knurled cap counterclockwise to remove cap and cutter from tool. 8. pply a very liberal amount of Sulflo (sulphur based cutting compound) to the end of the cutter.. Screw cap and cutter back into the body until the cutter contacts the end of the tubing. 0. Rotate handle of cutting tool clockwise fairly rapidly with one hand while slowly rotating the knurled cap clockwise with the other hand in order to continuously feed the cutter into the tubing. Do not overly force the cutter against the tubing as it will bind. (You will quickly develop the proper feel). You will need to rotate the knurled cap a complete number of turns as per the chart below in order to complete the cone on the end of the tubing. Tubing Size ack Off Turns O.D. 2 /2 turns O.D. /2 turns Threading the Tubing The threading tool is designed to put a left hand thread onto the end of the tubing. Operation is as follows:. The coning tool (with the knurled cap and cutter removed) provides an ideal way to hold the tubing for the threading operation (see photo). 2. fter securing the tubing, apply a liberal amount of Sulflo to the end of the tubing.. Place the threading tool (guide bushing side first) onto the tubing. 4. Place the palm of your hand firmly against the center of the threading tool and rotate your wrist counterclockwise. This will help start the die onto the tube. fter you feel the die start onto the tubing, continue to rotate the threading tool using the handles. 5. Remove the threading tool and clean off Sulflo and chips. NOTE: The tubing collar should easily screw onto the tubing. If it feels too tight or loose, the die should be adjusted accordingly. Simply remove the die from the holder by loosening the outer set screw. The small adjustment screw located on the side of the die can be turned to precisely set the die. O.D. 4 turns /6" O.D. /2 turns.4

106 High Equipment Vessels and Reactors High Equipment Company designs and manufactures a broad range of pressure vessels and reactors for both bench-scale and pilot plant applications. We have over 250 standard reactor designs which address varied size, material, pressure and temperature requirements. There are many applications that demand SME approval for work involving pressure vessels. To satisfy this need, HiP produces a variety of pressure vessels and reactors that meet the requirements of the SME Vessel Code. Complementing our standard product offering is our capability to provide a custom reactor designed to meet your specific needs. Our engineering and technical support will help you identify the specific options you need, ranging from exotic materials to unusual sizes and connections, and then incorporate the appropriate approvals, including SME. Index Page Vessel Selection O-Ring Seal Reactors Series OC Confined asket Closure Reactors - Series C olted Closure Reactors Clover Leaf Reactors O-Ring Closure Reactors Series R Tubular Reactors Series TOC Micro Reactors Series MS

107 High Equipment Reactor Selection uide Reactor Design Description Standard Material Maximum Temperature (degrees F) Maximum Working (psi) Standard Capacity O-ring Seal Series OC Simple closure design allows for easy assembly/disassembly and reliable operation. Series OC are economical reactors ideal for low temperature gas or liquid service. 6SS 250 6, ml to 6,50 ml Confined asket Closure Series C Series C is designed for studying high temperature and pressure reactions. The vessels utilize thrust bolts and a thrust ring to ensure positive seating of the gasket. 6SS 800 6, ml to 6,50 ml olted Closure Series C These versatile reactors are the standard of the industry for applications involving moderate pressure ranges. Standard O-rings may be used in place of the metal gasket for lower temperatures. 6SS 650 5, ml to 2 gal. Clover Leaf Series CL Quick opening cover design needs only one-eighth of a turn rotation for sealing. Ideal for high pressure operations requiring repetitive opening/closing. 440 alloy steel 250 0,000,000 ml to,00 ml O-ring Closure Series R Designed for extremely high pressure/low temperature operation, series R reactors feature a threaded closure for easy assembly and disassembly. 440 alloy steel ,000 ml to 0 liters Micro Reactors Series MS Series MS are fixed bed tubular reactors designed for a variety of applications such as small volume testing of components and miniature scale reaction tests. 6SS 800 0,000 2 ml to 64 ml Tubular Reactors Series TOC This line of economical and versatile reactors satisfy many moderate pressure applications. ccumulators can be customized through a variety of options including piston separators. 04SS O-ring 250 confined gasket 800 0, ml to 5 liters Custom Reactors HiP makes every reactor to order, allowing for economical and timely customizing. We offer a broad range of exotic metals, sizes and connections to meet virtually any requirement. 0.2 Note: For SME code stamping of HiP vessels, please consult factory for available reactor designs, materials, and pressure ratings. R 2/

108 Vessel Volume Table (cubic inches) Inside Depth (inches) Inside Diameter (inches) " 2 " 4" 5" 6" " 8" " 0" 4" " " " " " " " " " " Volume Equivalents in = 6. ml ml = 0.06 in gal = 2 in = 0.4 ft ft = 28 in =.48 gal L = 6.02 in = gal Conversions psi atm kg/cm 2 psi atm kg/cm High Equipment Company R 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 0.

109 High Equipment OC Series O-Ring Seal Reactors The OC Series provide a simple closure that is reliable and easy to assemble and disassemble. Standard material for the body and cover is Type 6 stainless steel. The standard O-ring material is UN-N. Temperature is limited by the O-ring to 250 F. These reactors are suitable for either gas or liquid service. Capacities range from 25 ml to 6,50 ml. Standard connections are for O.D. high pressure (coned and threaded) tubing (HF4). Models OC- and OC- have one connection in the cover. ll other models have two connections in the cover. Contact factory if other connections and/or locations are preferred. 2 Series OC Reactors Catalog No. I.D. O.D. OC-* " 2 Inside Depth Capacity Material 0" 25 ml 6 S.S. Working psi,800 OC-* OC " 0" 280 ml 280 ml 6 S.S. 6 S.S.,50 6,000 OC ml 6 S.S. 6,000 OC- 4 0" 500 ml 6 S.S. 2,500 4 DEPTH OC- OC ",040 ml 800 ml 6 S.S. 6 S.S. 2,500,200 OC-5 2 4,60 ml 6 S.S.,200 I.D. OC- OC- " " 6 6 0",50 ml 2,40 ml 6 S.S. 6 S.S.,000,000 OC-2 6 0",55 ml 6 S.S. 0,500 OC-2 6,00 ml 6 S.S. 0,500 OC-25 4" 6 0" 2,060 ml 6 S.S. 8,500 OC-2 4" 6 4,25 ml 6 S.S. 8,500. COVER 2. CP. "O" RIN 4. ODY 6 S.S. LLOY STEEL UN-N 6 S.S. OC-2 OC- OC- OC " 5" " 0" 2,600 ml 5,45 ml,200 ml 6,50 ml 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6,500 6,500 5,000 5,000 * One () opening only in cover 0.4 R2 2/

110 Confined asket Closure Reactors The Confined asket Closure reactors listed below are ideally suited for use at elevated temperatures and pressures as shown in the chart. Thrust bolts with a hardened thrust ring are supplied to insure positive seating of the gasket. Torque required on thrust bolts will range from 0 to 25 foot pounds, depending upon size of reactor, pressure, temperature and media being pressurized. Torquing of bolts should be done in a crisscross staggered pattern to insure uniform seating. commercial high temperature lubricant should always be applied to the bolt threads and outside cap threads to facilitate removal of the closure. Standard material for the body, cover and gasket is Type 6 stainless steel. These reactors are suitable for either gas or liquid service and capacities range from 25mL to 6,50 ml. Standard connections supplied are for O.D. high pressure (coned and threaded) tubing (HF4). Models C- and C- have one connection in the cover. ll other models have two connections in the cover and a thermowell that extends two-thirds of the inside depth. Included with each reactor are eye bolts for lifting and necessary collars and glands for the connections. Vise flats are machined on to the bottom of the body for securing while assembling or disassembling closure. Series C Reactors Catalog No. I.D. O.D. C- " 2 C- 2 C-5 4 C- 4 C- 4 C- 4 C- 2 4 C C- " 6 C- " 6 C-2 6 C-2 6 C-25 4" 6 C-2 4" 6 C C- 4 6 C- 5" 6 C-5 5" 6 Inside Depth Capacity Material 0" 0" 0" 0" 0" 0" 0" 0" 0" 0" 25 ml 280 ml 280 ml 600 ml 500 ml,040 ml 800 ml,60 ml,50 ml 2,40 ml,55 ml,00 ml 2,060 ml 4,25 ml 2,600 ml 5,45 ml,200 ml 6,50 ml 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. 6 S.S. Working (psi) 00 F 650 F 800 F,800,50 6,000 6,000 2,500 2,500,200,200,000,000 0,500 0,500 8,500 8,500 6,500 6,500 5,000 5,000 2,500,000 4,500 4,500,400,400 8,400 8,400,000,000,000,000,00,00 5,500 5,500 4,00 4,00 2,000 6,00 4,000 4,000,000,000 8,200 8,200 0,000 0,000 8,000 8,000 6,500 6,500 5,000 5,000 4,000 4, COVER 2. SET SCREW. CP 4. THRUST RIN 5. SKET 6. SKET. ODY 8. WEEP HOLE I.D. DEPTH 8 6 S.S. COMM. LLOY ST'L TOOL ST'L COPPER 6 S.S. 6 S.S. High Equipment Company R 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 0.5

111 High Equipment olted Closure Reactors The olted Closure Reactors are designed for use up to 650 F (4 C) at the working pressures indicated. Standard material for the body, cover and gasket is Type 6 stainless steel. Standard O-rings may be used in place of the metal gasket when temperatures permit. Standard connections include two high pressure (coned and threaded) tubing connections for O.D. tubing (HF4) located in the cover. Contact factory if other connections and/or locations are preferred. Other items available include: Heating mantle. Removable quartz fabric cylinder column type. 0 volt, single phase. olted closure reactors are supplied with mounting bolt holes on the bottom surface. Thermowell for use with /6" thermocouple Safety head located in side flange with rupture disc (see Page.) 2. PRESSURE CONNECTION (2) 2. SOCKET CP SCREW. COVER 4. SKET 5. MIN SEL 6. ODY. THERMOCOUPLE WELL* 8. SFETY HED* olted Closure Reactors * SUPPLIED S EXTR WHEN SPECIFIED Catalog No. Capacity Working psi Temperature F Inside Diameter Inside Depth pprox. Weight (pounds) pprox. Torque (ft-lb) per olt Material DEPTH C- 00 ml 5, " S.S. C-2 liter 5, " " S.S. I.D. C- 2 liter 5, S.S. C-4 gallon, " S.S. C-5 gallon 5, " S.S. C-6 2 gallon, " S.S. 0.6 R2 2/

112 Clover Leaf Reactors The Clover Leaf Closure Reactors provide maximum ease for quick opening or closing of the cover. The cover is simply inserted into the body and then rotated one-eighth of a turn. safety locking pin is provided to insure that the cover is properly positioned and locked. Standard material of construction for these reactors is heat treated 440 alloy steel. Standard connections include two high pressure (coned and threaded) O.D. tubing connections (HF4). Mounting holes are provided in the top and bottom of the body for securing or lifting. 2. LOCK PIN 2. COVER. O-RIN 4. ODY Clover Leaf Closure Reactors DEPTH I.D. 4 Catalog No. Inside Diameter Outside Diameter Inside Depth Working psi Temperature F Capacity Material CL- CL-2 CL- " 6 " 8" 2 0, ,000 ml 2,000 ml 2,500 ml lloy Steel CL-8 CL- " 4" 8" 0, ,850 ml,00 ml lloy Steel High Equipment Company R 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 0.

113 High Equipment Series R Reactors O-Ring Closure The Series R O-ring Closure Reactors are easily assembled and disassembled with minimal torque required for complete engagement. Material of construction for standard models is Type 440 alloy steel (or equivalent) properly heat treated for use at elevated pressures. (Some models can be provided in stainless steel construction at reduced pressures consult factory). Sealing is accomplished by a highly reliable combination of O-ring and separate metal back-up ring. The wedge shaped back-up ring is designed to expand and contract as pressure increases or decreases. Consequently, the O-ring is continuously confined with no clearance for extrusion. Minimal initial torque is required to effect a positive seal. Temperature on these vessels must be restricted to 250 F maximum, due to the UN-N (nitrile) O-ring. (continued on page 0.) 2 O-Ring Closure Reactors (one piece cover) I.D. O.D. psi Material Inside Depth 6" 0" 6" 20" 24" I.D. 4 5 " ,000 40,000 60,000 00,000 50, lloy Steel or equivalent R-6-0 R-6-40 R-6-60 R-6-00 R-6-50 R-0-0 R-0-40 R-0-60 R-0-00 R-0-50 R-2-0 R-2-40 R-2-60 R-2-00 R-2-50 R-6-0 R-6-40 R-6-60 R-6-00 R-6-50 DEPTH " 20,000 0,000 40,000 60,000 00, lloy Steel or equivalent R R R R R R R R R R R R R R R R R R R R ,000 R R R R COVER 2. ODY. VENT HOLE 4. CK UP RIN 5. "O" RIN 6. PRESSURE CONNECTION 4 5" ,000 0,000 40,000 60,000 00, lloy Steel or equivalent R R2-6-0 R R R R R2-0-0 R R R R R2-2-0 R R R R R2-6-0 R R R R R R R R R R R R R R 8/04

114 Included with each vessel is a Tony ar for removal of the cover nut and necessary eye bolt holes for lifting of the body and components. Outer surfaces are blackened to prevent rusting. Vent holes are provided to prevent pressure build up behind the closure in the event of a worn or damaged seal. Connections include a top and bottom high pressure coned and threaded O.D. (HF4) tubing connection. Other sizes or locations for connections can easily be provided when preferred. Consult factory. Closures are designed in one-piece (cover) for vessels up to I.D. and two-piece (cover and main nut) for vessels larger than I.D. O-Ring Closure Reactors (two piece cover) Inside Depth I.D. O.D. psi Material 6" 0" 6" 20" 24" " 4" 6" " 8 5" 8" " " 5" 20,000 0,000 40,000 60,000 00,000 20,000 0,000 40,000 50,000 60,000 R-6-20 R-6-0 R-6-40 R-6-60 R-6-00 R R4-6-0 R R R R-0-20 R-0-0 R-0-40 R-0-60 R-0-00 R R4-0-0 R R R R-2-20 R-2-0 R-2-40 R-2-60 R-2-00 R R4-2-0 R R R R-6-20 R-6-0 R-6-40 R-6-60 R-6-00 R R4-6-0 R R R R R-20-0 R R R R R R R R R R-24-0 R R R R R R R R , R R R R R R " 0,000 lloy R5-6-0 R5-0-0 R5-2-0 R5-6-0 R R Steel 40,000 or R R R R R R equivalent 6" " 8" " 0" 5 5" 0 " " 4 50,000 0,000 20,000 0,000 40,000 0,000 20,000 0,000 0,000 20,000 0,000 0,000 R R6-6-0 R R6-6-0 R R-6-0 R-6-20 R-6-0 R8-6-0 R R-6-0 R0-6-0 R R6-0-0 R R6-0-0 R R-0-0 R-0-20 R-0-0 R8-0-0 R R-0-0 R0-0-0 R R6-2-0 R R6-2-0 R R-2-0 R-2-20 R-2-0 R8-2-0 R R-2-0 R0-2-0 R R6-6-0 R R6-6-0 R R-6-0 R-6-20 R-6-0 R8-6-0 R R-6-0 R0-6-0 R R R R R R-20-0 R R-20-0 R R R-20-0 R R R R R R PRESSURE CONNECTION 2. MIN UNIT NUT. ODY 4. VENT HOLE 5. COVER 6. CK UP RIN. "O" RIN DEPTH I.D. SELIN DETIL High Equipment Company R2 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 0.

115 High Equipment Tubular Series Reactors The Tubular Series Reactors are double ended pressure vessels made from commercial quality cold drawn Type 04 stainless steel seamless tubing. Outside (non-wetted) caps are alloy steel. These are both economical and versatile vessels proven in demand for many applications. Finishes are commercial cold drawn finishes, with honed internal finishes. Standard sizes are shown in the chart on page 0., but special lengths and modifications are easily supplied on request. One pressure connection for O.D. high pressure coned and threaded tubing at each end is standard. dditional end connections are possible on the larger size models. lso, side connections and end cover thermowells can be supplied when required. Consult factory for special requirements. O-Ring Closures are standard when temperatures do not exceed 250 F. This is an easily assembled closure requiring minimal torque for positive sealing. The standard O-ring material used is UN-N (nitrile) with various other O-ring materials available on request. Confined asket Closures are available for temperatures up to 800 F. 5% reduction in the listed working pressure is required at this elevated temperature level. These closures utilize a metal gasket (04 stainless steel) which can be torqued down for positive sealing. Torque requirements on the thrust bolts will range from 60 to 0 foot pounds depending on size, pressure, temperature and media being pressurized. These confined gasket closures are available for all models except the TOC and TOC series. When ordering, simply specify catalog number and add suffix (W/asket). Piston Separators can be supplied with the O-ring closure vessels for use as compression cylinders. These are ideal for separating a liquid from a gas and other similar applications. The tubing body is supplied with a honed inside diameter surface to accommodate the piston. When ordering, simply specify catalog number and add suffix (W/Piston). 0.0 R 2/

116 Tubular Series Reactors Tubing Size Catalog Number (O-Ring Closure) I.D. O.D. psi Material 20"IL 40"IL 60"IL IL " 5,000 TOC-20 TOC-40 TOC-60 TOC-2 0,000 TOC-20 TOC-40 TOC-60 TOC-2 6,000 TOC5-20 TOC5-40 TOC5-60 TOC5-2 " 0,000 TOC-20 TOC-40 TOC-60 TOC-2 2 4,000 TOC-20 TOC-40 TOC-60 TOC " ",000,000 5,000,000 4,500 ody 04 S.S. Covers 6 S.S. TOC-20 TOC-20 TOC5-20 TOC-20 TOC-20 TOC-40 TOC-40 TOC5-40 TOC-40 TOC-40 TOC-60 TOC-60 TOC5-60 TOC-60 TOC-60 TOC-2 TOC-2 TOC5-2 TOC-2 TOC-2 O.D. DEPTH O.D. DEPTH O.D. DEPTH " 4" 4" 2,500 4,000 TOC2-20 TOC2-20 TOC2-40 TOC2-40 TOC2-60 TOC2-60 TOC2-2 TOC2-2 I.D. I.D. I.D. 4,000 TOC25-20 TOC25-40 TOC25-60 TOC25-2 " 4 5,000 TOC2-20 TOC2-40 TOC2-60 TOC2-2 4" 5",000 TOC2-20 TOC2-40 TOC2-60 TOC2-2 5" 2 5,000 TOC-20 2 TOC-40 TOC-60 2 TOC-2 O-RIN PISTON SKET PRESSURE CONNECTION 2. COVER. CP 4. "O" RIN 5. ODY (OTH ENDS LIKE) 6. PISTON. THRUST RIN 8. SKET. WEEP HOLE O-RIN PISTON SKET How To Order Tubular Series Reactors With O-Ring Closure: Specify catalog number, see ordering table above. Note: Use of una-n O-ring limits maximum working temperature to 250 F. For higher temperatures to 800 F, order gasket closure. With Piston Separators: Specify catalog number, see ordering table above and add (W/Piston) as suffix. ecause of temperature limitations pistons are not normally ordered in combination with the gasket closure. With asket Closure: Specify catalog number, see ordering table above and add W/asket) as suffix. * asket closure is not available on O.D. tubing size vessels. Example: TOC5-20 (W/asket). High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 0.

117 High Equipment Series MS Micro Reactors The Micro Reactors shown are designed for numerous applications including small volume testing of components and miniature scale reaction tests. Standard material of construction is Type 6 stainless steel. Operation at temperatures up to 800 F is made possible by the metal to metal seal construction. Working pressures should be reduced by approximately 5% at the maximum 800 F temperature level. Connections are for O.D. high pressure coned and threaded tubing (HF4). One connection is provided at each end. Other sizes or types of connections can be provided. Thermocouples can easily be installed with the use of thermocouple adapters (refer to section 8.0). I.D. (C) O.D. (D) Working (C) (D) () () Catalog Inside Outside Inside Overall No. Capacity psi Diameter Diameter Depth Length MS- MS-2 MS- MS-4 MS-5 MS- MS-2 MS- MS-4 MS-5 MS-6 MS- MS-8 MS- 2 ml ml 4 ml 5 ml 6 ml 5 ml /2 ml 0 ml 2 /2 ml 5 ml 24 ml 4 ml 65 ml 8 ml 60,000 20,000 20,000 /6" 5 /6" /6" /6" /6" " 4" 6" 8" 0" 4" 6" 8" 0" 6" 0" 6" 20" " " " " 5" " " " 0.2 R 2/

118 High Equipment Pumping Systems, Intensifiers, as oosters and High enerators High Equipment Company produces a number of components and systems for general industrial, elevated pressure applications. Pumping Systems are air operated, hydraulic systems capable of producing output pressures up to 50,000 psi. These pumping systems are complete, self-contained and ready to operate; just connect to shop air supply. Hydraulic Intensifiers feature a compression ratio of 0 to, which allows for output pressures as high as 50,000 psi when used in conjunction with a commercially available lower pressure pump (5,000 psi). as oosters and gas booster systems are an excellent method for increasing the pressures or flow rates for a variety of gases. These units offer compression ratios as high as 0 to and output pressures up to 60,000 psi. High enerators are manually operated piston screw pumps for compressing liquids and some gases in small volumes to develop pressure. Index Page Pumping Systems Intensifiers as oosters High enerators

119 High Equipment ir Operated Hydraulic Pumping Systems to 50,000 psi Model PS-0: 0,000 psi Model PS-20: 20,000 psi Model PS-0: 0,000 psi Model PS-40: 40,000 psi Model PS-50: 50,000 psi Model PS-0: 0,000 psi High air operated hydraulic pumping systems are complete, selfcontained units and ready to operate. Just hook up standard shop air supply (maximum 00 psi) to connection supplied on the side of the console. Discharge capacities range to 64 in /min. Standard Features System includes hydraulic oil reservoir, oil filter, air operated hydraulic pump, pressure gauge, panel mounted high pressure valves, safety head assembly, panel mounted air regulator and gauge and air line filter and lubricator. ll components are enclosed in a steel console with only the back exposed. Dimensions of standard systems are 26" wide, 24" deep and 40" high..2 R4 2/02

120 System Capabilities The output pressure is predetermined by adjustment to the air regulator setting. Output pressure is maintained constantly and pump compensates for pressure drops or losses. Hydraulic input is gravity fed, however, if pump is used alone, the feed can be pressurized to the limit of the pump. Within the pump the large diameter air piston drives a smaller piston to provide fluid flow at high pressure. ir consumption will be approximately 56 CFM of free air at 00 psi input. Reservoir = 4 gallon capacity, do not pressurize. 00 psi MX IR INLET SUPPLIED WITH REULTOR FILTER ND LURICTOR PRESSURE UE HIH PRESSURE OUTLET RESERVOIR IR OPERTED HYDRULIC PUMP Standard Pumping System Specifications pproximate ir to Hydraulic Ratio Static Conditions Hydraulic psi Model ir psi No PS-0,500,200 5,200,00,000 0,800 2,500 4,500 6,00 8,000,800 PS-20,000 6,000,500 2,600 6,000,00 22,00 25,600 2,000 2,00 5,600 PS-0 4,000 8,800,00 8,000 22,500 2,000,500 6,500 4,400 45,800 50,00 PS-40 6,000,000 2,000 2,000 4,000 40,500 46,000 52,000 5,000 65,000 0,000 PS-50 6,000,000 2,000 2,000 4,000 40,500 46,000 52,000 5,000 65,000 0,000 PS-0 Uses Dual Pump N/ N/ N/ N/ N/ N/ N/ N/ pproximate Rate of Discharge CIPM Model ir psi PS-0 PS-20 PS-0 PS-40 PS ,000 psi ,000 psi ,000 psi ,000 psi High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

121 High Equipment 50,000 psi Pumping System Model PS-50 The Model PS-50 Pumping System is designed for generating hydraulic pressure up to 50,000 psi by means of an air operated hydraulic pump and an intensifier. The 0 to ratio intensifier is fully illustrated on facing page.5. This system is complete and ready to operate requiring only the connection of an air supply of approximately 80 psi. The steel console is 26" wide, 24" deep, 40" high and includes manual valves, air regulator, filter and lubricator, air gauge, high pressure gauge, reservoir, oil filter, pump (0-6,000 psi), related high pressure tubing and fittings. The 0-20,000 psi pressure gauge is connected to the low pressure side of the intensifier which has a ratio of 0 to. on the high pressure side of the intensifier is thus determined by multiplying the gauge reading by 0. small variation must be allowed for friction from the intensifier packing. The air operated hydraulic pump pressurizes the system to 6,000 psi with valves and closed and the intensifier piston is automatically positioned to the low pressure end of its stroke. With valves and C closed, valve is opened to allow the pump to pressurize the low pressure end of the intensifier. The fluid in the high pressure end of the intensifier is thus pressurized with a 0 to ratio. If the intensifier reaches the end of its stroke before the desired pressure is achieved, the intensifier may be recycled. The intensifier output is approximately.2 cubic inches per stroke. 00 psi MX IR INLET SUPPLIED WITH REULTOR FILTER ND LURICTOR RETURN LINE INTENSIFIER CHECK VLVE PRESSURE UE C RESERVOIR IR OPERTED HYDRULIC PUMP.4 R 2/

122 50,000 psi Hydraulic Intensifiers The 50,000 psi Hydraulic Intensifier is designed with a ratio of areas on the two pistons of 0 to. Consequently, pressures up to 50,000 psi can be achieved by using a commercially available lower pressure (5,000 psi) pump. Operation of this intensifier is illustrated in the typical installation shown in the schematic on facing page.4. Material of construction for the pressure containing parts is 440 alloy steel (or equivalent) properly heat treated for use at elevated pressures. Only non-corrosive type fluids should be used. The high pressure packing is housed in a separate removable stuffing box. This design permits improved concentricity and facilitates close tolerance machining of the packing area. Capacity per stroke at the high pressure end is.2 cubic inches. Capacity at the low pressure end is 2.6 cubic inches per stroke. Piston travel is 4 inches. Weight is approximately 50 pounds. Standard connections are for O.D. tubing (HF4) on the low pressure end and O.D. x /6" I.D. tubing (XF6) on the high pressure end. " 6" High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

123 High Equipment as oosters MODEL S - 0 0,000 psi as ooster System (One-to-one ratio 2 cubic inch per stroke displacement) (-4PH stainless steel construction) MODEL S ,000 psi as ooster System (Thirty-to-one ratio 4. cubic inch per stroke displacement) (440 alloy steel construction) The Model S-0 and S-60 as ooster Systems are complete and ready to operate. ll that is required is an air supply for the pump (approximately 0 psi) and a commercially available container of compressed gas. The steel console is 26" wide, 24" deep, 40" high and includes manual valves, air regulator, filter and lubricator, air gauge, high pressure gauge, reservoir, oil filter, pump, gas booster and related high pressure tubing and fittings. Operation is by means of an air operated hydraulic pump which pressurizes one end of the gas booster which then compresses the gas in the opposite end of the booster. To accomplish this, the gas inlet valve is opened to permit gas to fill the gas end of the booster. Check valves are provided to permit gas flow in one direction only. With the gas outlet valve open, the hydraulic pump is operated in order to pressurize the hydraulic end of the booster. Thus, the gas is compressed in the booster. If required pressure is not reached by the end of the stroke, the gas booster can easily be recycled for additional strokes. Note the gauge on these systems is connected to the hydraulic side of the booster. On the Model S-0 which has a to ratio, there is a direct reading of the pressure in the gas end of the booster. The Model S-60 has a 0 to ratio and the gauge will accordingly indicate a reading of one-thirtieth (/0) of the actual pressure in the gas end of the booster. n additional gauge can be furnished for connection to the gas end of the booster to provide direct pressure readings of the gas pressure. Details of the gas boosters are shown on facing page.. These systems should not be used with hydrogen or oxygen. S INLET COMPRESSED S OUTLET IR INLET IR REULTOR OIL S OOSTER CYLINDER INTENSIFIER TYPE PRESSURE UE VENT RESERVOIR IR OPERTED HYDRULIC PUMP (Schematic shows 60,000 psi ooster) RETURN LINE.6

124 as oosters Model -0 0,000 psi " The Model -0 as ooster is rated for use up to 0,000 psi and has a one-to-one ratio. Displacement per stroke is 2 cubic inches (85 ml). Material of construction is -4PH stainless steel for the body and covers. The piston is supplied in brass with other materials available as an option. Standard O-ring material for the covers and piston is UN-N (nitrile). Standard connections supplied are for O.D. High tubing (HF4 connection) at each end. The Model -0 can be supplied as a separate unit or with the complete system (Model S-0) shown on page.6. The Model -0 should not be used with hydrogen or oxygen. Model ,000 psi HIH PRESSURE END 0" The Model -60 as ooster is rated for use up to 60,000 psi and has a thirty-to-one (0-) ratio. Thus, 60,000 psi can be obtained at the high pressure end using only 2,000 psi inlet pressure. Displacement per stroke is 4. cubic inches ( ml). Material of construction is Type 440 alloy steel (or equivalent) properly heat treated for use at high pressure. Other internal materials include -4PH stainless steel and aluminum bronze. Seals include UN-N (nitrile) O-rings and a Parker Poly Pak. Standard connections supplied are for O.D. High tubing (HF4 on the high pressure end and F4 on the low pressure end). The Model -60 can be supplied as a separate unit or with the complete system (Model S-60) shown on page.6. The Model -60 should not be used with hydrogen or oxygen. Piston travel - 6" LOW PRESSURE END Special as oosters and Intensifiers High Equipment Company has designed and supplied numerous gas boosters and intensifiers to meet the customer's special requirements. price quotation can be made by advising us of the requirements including: media (gas or liquid) to be pressurized, maximum outlet pressure required, available inlet pressure and required displacement per stroke. High Equipment Company R4 2/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

125 High Equipment High enerators The HiP High enerator is a manually operated piston screw pump. It is designed for any application where a liquid* is to be compressed within a small volume to develop pressure. Ranges: 0-5,000 psi 0-0,000 psi 0-5,000 psi 0-0,000 psi 0-60,000 psi 0-5,000 psi 0-00,000 psi ll wetted parts are of 6 stainless steel and -4PH stainless steel. Parker Poly Pak is standard. The High enerator is easily mounted to a work bench and maximum pressures may be obtained with a minimum amount of effort by the operator. The standard connection is a High coned-and-threaded (HF4) opening for O.D. tubing up to 60,000 psi and XF4 connections for pressures above 60,000 psi. dapters are available with optional Teflon packing at no additional cost for other type connections including pipe. Typical pplications: Testing of instruments, gauges, component parts measurement studies Injection of liquid catalysts Pressurizing chemicals convenient source of high pressure in the laboratory Extra Capacity Model Standard Laboratory Model Vernier Indicators as shown in the photo at left are available as an accessory on all of the Standard Laboratory Models. These indicators provide controlled measurement of column displacement with an accuracy of ± 0.00" movement of stroke. * If required for S application, please consult factory..8

126 High enerators The schematic illustrates a very basic layout for using a enerator. reservoir (R) is shown connected by means of valves and fittings to a component (C) that is to be pressurized. gauge has been included for determining pressure. With valve closed and valve open, the handle of the enerator is rotated counter-clockwise to draw fluid from the reservoir into the cylinder body of the enerator. Valve is then closed and valve is opened. y rotating the enerator handle clockwise, the piston will now compress the fluid to develop pressure in the component that is to be pressurized. If sufficient pressure is not reached in one stroke, the system can be recycled. Valve can be closed in order to maintain pressure in the components. Valve is then opened, and fluid is again drawn into the enerator from the reservoir. Closing Valve and opening Valve will now allow the enerator to be operated to develop increased pressure in the component. in the component can be vented by opening both valves. R C Component to be pressurized Numerous variations and additions to this basic layout are possible. Standard Laboratory Models 8" 8.5" to 24" 4 2 " " 8" 5 " 6 8 ". Handle 2. land Nut. Mounting racket 4. Top Packing Washer 5. Packing * 6. ottom Packing Washer. Shaft 8. ody Model psi Capacity per Stroke Shaft Diameter , ml ,000 0 ml , ml ,000 ml Length of stroke: 6 inches. 4 revolutions of handle produces one inch travel of shaft. * Use item six only with optional Chevron Teflon packing. Extra Capacity Models 0" 0 24" " " " 8" " 8. Handle 2. Housing. Mounting racket 4. Packing Washer 5. Packing 6. Extension land. Shaft 8. ody. Stem Screw with Keyway 0. earing ssembly. Key Model psi Capacity per Stroke Shaft Diameter ,000 ml , ml /6" ,000 5 ml /6" ,000 8 ml ,000 0 ml ,000 ml 5 /6" , ml Length of stroke: 5 /4 inches. 4 revolutions of handle produces one inch travel of shaft. High Equipment Company R 2/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

127 High Equipment Technical Information Selecting the right product to plumb your pressure system or conduct your research project is a critical decision. In this section, High Equipment Company provides a variety of technical information to assist you in this selection process. We have included a number of English to Metric conversion charts, flow coefficient formulas and valve ratings, reactor pressure ratings, and recommended torque values for our air operated valves and tubing connections. s you work with this data, it is important to consider that it is general in nature and may vary depending on the actual parameters of your application. If you have any questions concerning this information or would like assistance in selecting an HiP product, our engineering staff is available and ready to help. Index Page Conversion Tables Packing Options Minimum Safety Hold Down Nut Torque Minimum end Radius For High Tubing Flow Coefficients s of olted Closure Reactors Recommended Torque s For: Equipment in Various Common Materials Tubing in Various Materials Maximum Recommended Volumetric Flow Rate Reduction 6-04 SS Components at Elevated Temperatures raphs Temperature For Taper Seal Valves & Fittings.2.0 Reduction 6-04 SS Components at Elevated Temperatures Micrometering Valve Flow R5 4/ 2.

128 High Equipment Pa kpa psi kg/cm 2 bar atm MPa Pa kpa psi kg/cm 2 bar atm MPa x x 0-5 x x 0-6 x x x x x x Flow ml/min in /min ft /hr liter/min gal/min ml/min in /min ft /hr liter/min gal/min x Weight/Mass gram oz lb kg gram oz lb kg Volume ml in liter gal ft m ml in liter gal ft m x x 0 4 x x x x x x x x Linear micron millimeter centimeter inch foot meter micron millimeter centimeter inch foot meter 000 x x x 0 5 x x x x 0-6 x R 8/04

129 Conversion Tables Temperature Fahrenheit to Celsius Celsius to Fahrenheit High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2. C F C F C F F C F C F C F = /5 C + 2 C = 5 / ( F - 2) R = F K = C R 2/

130 High Equipment Packing Options NPT Hand Valves 0,000 psi Series 5,000 psi Series Part Number Material NF/NF/ NFC NFD NFF - NFH Teflon* Set rafoil -4-5 una-n -02 Viton -84 Silicone -4 Part Number Material NF NFC NF NFD Teflon* -2 Set 204 Set rafoil - Set -86 Set Polypak -88 () -8 () Hand Valves Taper Seal Part Number Material F F2 F4/ F6 Teflon* rafoil una-n Viton Silicone Medium Part Number Material LF4/ LF6 LF LF2 LF6 Teflon* -2 Set 204 Set Set 2084 Set rafoil - Set -86 Set -455 Set -440 Set 2 Polypak -88 () -8 () -4 () -42 () 2 LF2 Series: When rafoil and Polypak are used, top washer 208 and bottom washer 208 must be installed 2 LF6 Series: When rafoil and Polypak are used, top washer 2008 and bottom washer 200 must be installed High 0,000 psi Part Number Material HF2 HF4/HF6 HF HF6 Teflon* Set rafoil Set una-n Viton Silicone -4-4 Polypak -4 () High 60,000 psi Part Number Material HF2/HF4/ HF6/HF Teflon/Nylon** 2068 rafoil - TFE/Viton 2240 Ultra High Part Number Material XF4/ XF6 Teflon/Nylon** 2086 HF6 Series: When rafoil and Polypak are used, top washer 20 and bottom washer 208 must be installed * Teflon packing supplied as standard ** Teflon/Nylon packing supplied as standard Note: For pricing see Spare Parts list in Price List 2.4 R 4/

131 NPT ir Operated Valves HIPCO 0,000 psi Series Part Number Material NF NF Teflon* -8 rafoil -4 una-n -02 Viton -84 Silicone -4 HIPCO 5,000 psi Series Part Number Material NF NFC NF NFD Teflon* -2 Set 204 Set rafoil - Set -86 Set Polypak -88 () -8 () Packing Options HIPPO 5,000 psi Series Part Number Material NF NFC NF NFD Teflon* -2 Set 204 Set rafoil - Set -86 Set Polypak -88 () -8 () ir Operated Valves HIPCO Taper Seal Part Number Material F4 F6 Teflon* -8 una-n -02 Viton -84 Silicone -4 HIPPO Taper Seal Part Number Material F4 F6 Teflon* -8 una-n -02 Viton -84 Silicone -4 Mini HIPPO Part Number Material F2 F4/ HF4/HF6/ F6 HF Teflon* una-n Viton Silicone HIPCO Medium Part Number Material LF4/ LF6 LF Teflon* -2 Set 204 Set rafoil - Set -86 Set Polypak -88 () -8 () HIPCO High 0,000 psi Part Number Material HF4/HF6/ HF Teflon* -8 rafoil -4 TFE/una-N 2026 HIPCO High 60,000 psi Part Number Material HF2/HF4/ HF6/HF Teflon/Nylon** 2068 rafoil - TFE/Viton 2240 HIPPO Medium Part Number Material LF4/ LF6 LF Teflon* -2 Set 204 Set rafoil - Set -86 Set Polypak -88 () -8 () HIPPO High 0,000 psi Part Number Material HF4/HF6/ HF Teflon* -8 rafoil -4 TFE/una-N 2026 HIPPO High 60,000 psi Part Number Material HF2/HF4/ HF6/HF Teflon/Nylon** 2068 rafoil - TFE/Viton 2240 Temperature s for Packing Options Maximum Material Temperature una-n 200 F rafoil 800 F PolyPak 200 F Silicone 400 F Teflon 450 F TFE/Nylon 80 F TFE/Viton 400 F Viton 400 F * Teflon packing supplied as standard ** Teflon/Nylon packing supplied as standard Note: For pricing see Spare Parts list in Price List High Equipment Company R 4/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.5

132 High Equipment Minimum Safety Head Hold Down Nut Torque psi Torque foot pounds 0, , , , , , , , , , ,000 0 Minimum Recommended end Radius For High Tubing Tube Size O.D. x I.D x x x x x x x x x x x x x 0.56 " x 0.48 " x " x Minimum end Radius.25 in.5 in 2.62 in.50 in 4.62 in Flow Coefficients The flow coefficient Cv is a valve sizing designation commonly determined by laboratory test. It corresponds to the flow rate of water through a valve in US gallons per minute at 60 F with a differential pressure drop of one psi. Flow coefficients of various HiP valves Valve 5-F 5-F2 0-F4 0-F6 20-LF4 20-LF6 20-LF 0-LF2 20-LF2 0-LF6 20-LF6 0-HF2 0-HF4 0-HF6 0-HF 0-HF6 C v Valve 40-HF 60-HF2 60-HF4 60-HF6 60-HF 00-XF4 50-XF6 0-NF 0-NF 0-NFC 0-NFD 5F-NF 5F-NF 5F-NFC 5F-NFD 0F-NFF 0F-NFH C v With the Cv coefficient known, the following values can be calculated:. Liquid flow capacity in US gallons per minute 2. drop across valve (liquid flow). as flow capacity in standard cubic feet per hour (SCFH) 4. drop across valve (gas flow) Ql = Cv. P P =. Ql 2 Cv 2 Qg = 60. Cv. P = Where: Cv = Valve flow coefficient = Specific gravity of fluid P = Differential pressure drop across valve (psi) P = System pressure at valve inlet (psia) Ql = Liquid flow in US gallons per minute (PM) P. P T.. Z T.. Z.( Qg P 60. Cv Qg = as flow in standard cubic feet per hour (SCFH) T = System temperature ( R) Z = as compressibility factor at operating conditions ) R6 2/

133 s olted Closure Reactors (psi) at Elevated Temperatures Temperature C-2, F ( C) C- C-, C-5 C-4, C-6 00 (8) 200 () 00 (4) 400 (204) 500 (260) 600 (6) 650 (4) Temperature C-2, F ( C) C- C-, C-5 C-4, C-6 00 () 50 () 800 (42) 850 (454) 00 (482) 50 (50) 000 (58) Recommended Torque Tubing Connections Minimum Packing land Torque for Valves Connection F F2 F4 F6 LF4 LF6 LF LF2 LF6 HF2 HF4 HF6 HF HF6 XF4 XF6 Recommended Torque 55 inch pounds 0 foot pounds initial to compress sleeve onto tube 25 foot pounds to tighten connection 0 foot pounds initial to compress sleeve onto tube 50 foot pounds to tighten connection 40 foot pounds initial to compress sleeve onto tube 60 foot pounds to tighten connection 20 foot pounds 0 foot pounds 50 foot pounds 0 foot pounds 25 foot pounds 5 inch pounds 25 foot pounds 50 foot pounds 0 foot pounds 50 foot pounds 45 foot pounds 0 foot pounds Valve Series Packing land Torque 5-**F 5-**F2 5,000 psi 5 foot pounds 0-**F4 0-**F6 0,000 psi 0 foot pounds 0-**NF 0-**NF 0-**NFC 0-**NFD 0,000 psi 0,000 psi 5 foot pounds 50 foot pounds 20-**LF4 20,000 psi 20-**LF6 20,000 psi 5 foot pounds 20-**LF 20,000 psi 0 foot pounds 0-**HF2 0-**HF4 0-**HF6 0-**HF 60-**HF2 0,000 psi 0 foot pounds 60-**HF4 60-**HF6 60-**HF 00-**XF4 60,000 psi 00,000 psi 40 foot pounds 60 foot pounds 50-**XF6 50,000 psi 0 foot pounds High Equipment Company R5 8/ W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.

134 High Equipment s Equipment in Various Common Materials 6SS CW 6 SS 6L SS Duplex Duplex Hast C26 Material (std rating) nnealed nnealed nnealed 60,000 psi 0,000 psi 26,250 psi 54,000 psi 60,000 psi 4,000 psi 0,000 psi 20,000 psi,000 psi 2,000 psi 0,000 psi 20,500 psi at Room 20,000 psi 0,000 psi 8,50 psi 8,000 psi 20,000 psi,500 psi Temperature 5,000 psi 2,000 psi 0,000 psi 5,000 psi 5,000 psi 5,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi Inconel Inconel Titanium sol Inconel Monel Titanium rade 5 Material nnealed nnealed 8 nnealed rade 2 (64V) 254 SMo 4,500 psi 40,500 psi 60,000 psi 28,250 psi 0,000 psi 60,000 psi 4,500 psi,250 psi 20,250 psi 0,000 psi 4,000 psi 5,000 psi 0,000 psi 2,50 psi at Room,500 psi,500 psi 20,000 psi,250 psi 0,000 psi 20,000 psi 4,500 psi Temperature 5,000 psi 5,000 psi 5,000 psi,000 psi 0,000 psi 5,000 psi 5,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi 0,000 psi Tubing in Various Materials * Tubing Material vs Size OD x ID Hastelloy Inconel Monel Nickel Titanium (inches) 6 CW C r 2 /8 x ,000 psi 0,400 psi 8,50 psi,50 psi 4,25 psi,65 psi Low /4 x ,000 psi 6,50 psi 5,650 psi 4,625 psi 2,65 psi 4,5 psi /8 x ,000 psi 6,50 psi 5,650 psi 4,625 psi 2,65 psi 4,5 psi /4 x ,000 psi,500 psi,25 psi,25 psi 5,50 psi,50 psi /8 x ,000 psi,500 psi,25 psi,25 psi 5,50 psi,50 psi /6 x 0.5 0,000 psi 6,50 psi 5,650 psi 4,625 psi 2,65 psi 4,5 psi Medium /6 x ,000 psi,500 psi,25 psi,25 psi 5,50 psi,50 psi /4 x ,000 psi 6,50 psi 5,650 psi 4,625 psi 2,65 psi 4,5 psi /4 x ,000 psi,500 psi,25 psi,25 psi 5,50 psi,50 psi x ,000 psi 6,50 psi 5,650 psi 4,625 psi 2,65 psi 4,5 psi x ,000 psi,500 psi,25 psi,25 psi 5,50 psi,50 psi /8 x ,000 psi 4,00 psi 5,000 psi 28,650 psi 6,55 psi 0,00 psi /8 x ,000 psi 20,850 psi,500 psi 4,25 psi 8,25 psi 5,50 psi /4 x ,000 psi 5,5 psi 0,5 psi 24,25 psi 4,00 psi 26,45 psi High /8 x ,000 psi 5,5 psi 0,5 psi 24,25 psi 4,00 psi 26,45 psi /6 x ,000 psi 5,5 psi 0,5 psi 24,0 psi 4,00 psi 26,45 psi /6 x ,000 psi 2,000 psi 22,65 psi 8,55 psi 0,25 psi,00 psi x 0.4 0,000 psi 20,25 psi,000 psi,25 psi 8,050 psi 4,25 psi * Not all tubing sizes available in all materials. 2.8 R5 4/

135 Volumetric Flow Rate Maximum Recommended Volumetric Flow Rate for Water through a Tube Orifice Size Max Flow pproximate (inches) (gpm) P (psi/ft) <0 <0 <0 <0 <0 Orifice Size Max Flow pproximate (inches) (gpm) P (psi/ft) <0 <0 < < < < < < < < < < < <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 <5 Reduction 6 and 04 SS components at elevated levels. Temperature Percent of Room F ( C) Temperature Up to 00 (8) () (4) (204) (260) (6) 85 Temperature Percent of Room F ( C) Temperature 650 (4) 8 00 () () (42) (45) 8.5 Intermediate values may be linearly interpolated. High Equipment Company 4/ 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website: 2.

136 High Equipment Temperature Taper Seal Series Valves and Fittings % of Room Temp F Max. Recommended Temperature ( F) Reduction 6 and 04 SS Components at Elevated Temperatures Micrometering Valve Flow 60-HF4-V % of Room Temp Cv Temperature ( F) Number of Turns Open 2.0 4/

137 Valves Fittings Tubing High Equipment Company CERTIFIED Oil & as Products

138 Oil and as Products High Equipment Company has developed a complete line of valves and affiliated components specifically for the unique requirements of the oil and gas industry. We offer valves, fittings and tubing for use with sour oil and gas (H 2 S) in a 0,000 psi, 20,000 psi and 0,000 psi series. Our SS products are constructed of annealed 6 stainless steel and meet or exceed all requirements of NCE MR05 and the merican Petroleum Institute. For those applications where H 2 S is not present, our standard line of valves, fittings and tubing will accommodate pressures to 50,000 psi. Since 54, HiP has been designing and manufacturing the highest quality and most dependable high pressure oil field products. Our ISO 00 certified operation is part of a quality focus that has helped us gain the trust of many new oil and gas customers. nd our on-time delivery and competitive pricing have made us integral partners in our customers cost-reduction efforts. Hastelloy & Other Exotic Material Products in Stock We know that some oil and gas applications demand material performance beyond our SS stainless steel products. In an effort to provide our customers with their material of choice and meet tight shipping deadlines, we maintain an inventory of Hastelloy and Monel valves and fittings. Sour Oil & as Valves, & /6" O.D. tube connections 0,000, 20,000 & 0,000 psi series Vee and regulating stem types nnealed 6 stainless steel construction Meet or exceed requirements of NCE MR05 High Coned and Threaded Connections HiP oil field products use a high pressure coned and threaded connection which accommodates the high temperatures, high pressures and extreme conditions common in these applications. These connections may be disassembled and retightened indefinitely. HF4 ( ), HF6 ( ) and HF ( /6") Tubing land Collar.2

139 Sour Oil and as Valves Two Way Straight Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness K O.D. 0-HF4-SS 20,000 HF4 5 /6" 5 " 2 /6" " D F L E J H O.D. /6" O.D. O.D. O.D. 0-HF6-SS 0-HF-SS 60-HF4-SS 60-HF6-SS 20,000 20,000 0,000 0,000 HF6 HF HF4 HF6 /6" /6" 5 /6" /6" 5 /6" " 5 5 " /6" " " 2 /6" 2 2 /6" 2 /6" " " " /6" O.D. 60-HF-SS 0,000 HF /6" " /6" 2 Two Way ngle Valves D L E K J H Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. /6" O.D. O.D. O.D. /6" O.D. 0-2HF4-SS 0-2HF6-SS 0-2HF-SS 60-2HF4-SS 60-2HF6-SS 60-2HF-SS 20,000 20,000 20,000 0,000 0,000 0,000 HF4 HF6 HF HF4 HF6 HF /6" /6" /6" 5 /6" 5 /6" /6" 5 /6" " /6" " /6" 2 /6" 2 /6" 2 2 /6" 2 /6" 2 " " " " Three Way Valves / Two Connections Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness D L F E K J H O.D. O.D. /6" O.D. O.D. O.D. /6" O.D. 0-HF4-SS 0-HF6-SS 0-HF-SS 60-HF4-SS 60-HF6-SS 60-HF-SS 20,000 20,000 20,000 0,000 0,000 0,000 HF4 HF6 HF HF4 HF6 HF /6" /6" /6" 5 /6" 5 /6" 6 /6" 5 /6" 5 /6" 6 /6" " /6" 5 " /6" " " 2 /6" 2 /6" 5 /6" 2 /6" 2 /6" 2 5 /6" " " " " Three Way Valves / One Connection Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness D F L E E K J H O.D. O.D. /6" O.D. O.D. O.D. /6" O.D. 0-4HF4-SS 0-4HF6-SS 0-4HF-SS 60-4HF4-SS 60-4HF6-SS 60-4HF-SS 20,000 20,000 20,000 0,000 0,000 0,000 HF4 HF6 HF HF4 HF6 HF /6" /6" /6" 5 /6" 5 /6" /6" 5 /6" " 2 /6" " /6" " /6" /6" " /6" 2 /6" 2 /6" 2 2 /6" 2 /6" 2 " " " " J F L D K F J D L E E K J H H Three Way / Two Stem Connection Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. 0-5HF4-SS 0-5HF6-SS 20,000 20,000 HF4 HF6 " /6" /6" 4" 2 " " " 0-5HF-SS 20,000 HF /6" /6" 4 O.D. 60-5HF4-SS 0,000 HF4 /6" /6" 2 " O.D. 60-5HF6-SS 0,000 HF6 /6" /6" 4" " " 60-5HF-SS 0,000 HF /6" /6" /6" 4 /6" O.D. /6" O.D. Replaceable Seat Valves Tubing Catalog No. psi Connection Orifice D E F H J K L Thickness O.D. O.D. 0-2HF4-R-SS 0-2HF6-R-SS 20,000 20,000 HF4 HF6 5 /6" 5 /6" " 2 /6" 2 /6" " " 0-2HF-R-SS 20,000 HF _ /6" 2 O.D. 60-2HF4-R-SS 0,000 HF4 /6" 5 /6" _ " 2 /6" " O.D. 60-2HF6-R-SS 0,000 HF6 /6" 5 /6" _ 2 /6" " 60-2HF-R-SS 0,000 HF /6" _ /6" 2 /6" O.D. /6" O.D. High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

140 Oil and as ccessories lands/sleeves/plugs/elbows/tees/crosses complete range of elbows, tees, and crosses is available for use with sour oil and gas. Material is annealed 6 stainless steel. ll connection components and fittings are rated for 0,000 psi service. Standard tubing glands and collars are provided unless otherwise specified. Connection Components Tube Catalog No. Size land 60-2HM4-SS 60-2HM6-SS 60-2HM-SS /6" Tube Catalog No. Size Collar 60-2H4-SS 60-2H6-SS 60-2H-SS /6" Tube Catalog No. Size Plug 60-HM4-SS 60-HM6-SS 60-HM-SS /6" E H F High Elbows Catalog No. psi Connections - E F H Thickness 60-22HF4-SS 0,000 O.D. TUE HF4 " " 60-22HF6-SS 0,000 O.D. TUE HF6 " " 60-22HF-SS 0,000 /6" O.D. TUE HF 2 5 C E H F High Tees Catalog No. psi Connections --C E F H Thickness 60-2HF4-SS 0,000 O.D.TUE HF4 " " 60-2HF6-SS 0,000 O.D.TUE HF6 /6" " /6" " 60-2HF-SS 0,000 /6" O.D.TUE HF C E D H F High Crosses Catalog No. psi Connections --C-D E F H Thickness 60-24HF4-SS 0,000 O.D. TUE HF4 " " 60-24HF6-SS 0,000 O.D. TUE HF6 2 /6" " " 60-24HF-SS 0,000 /6" O.D. TUE HF /6" Union Couplings (Slip Type) Union (slip Type) couplings are ideal for use in confined space installations. This design allows the entire coupling to be disconnected and slipped back over the tubing to facilitate assembly and disassembly. In installations where tubing is easily assembled, it is preferable (and less expensive) to use standard straight couplings (see accessories section). Sour oil and gas material is annealed 6 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. Hex Catalog No. psi Connections Length Size 60-2HF4-U-SS 0,000 O.D. TUIN HF4 HF4 " 60-2HF6-U-SS 0,000 O.D. TUIN HF6 HF6 " 60-2HF-U-SS 0,000 /6" O.D. TUIN HF HF 2.4

141 ulkhead Couplings ulkhead couplings are designed specifically for passing a tubing connection through a panel or steel barricade. These couplings include a locknut as shown. Material is annealed 6 stainless steel. Standard tubing collars and glands are included unless otherwise specified. Panel Hex Outside Catalog No. psi Connections Hole Length Size Thread 60-2HF4--SS 0,000 O.D. TUIN 5 /6" HF4 HF4 " HF6--SS 0,000 O.D. TUIN HF6 HF6 2 /6" HF--SS 0,000 /6" O.D. TUIN /6" HF HF Locknut Caps Tubing end caps are offered for use in sealing off tubing ends either for temporary use or permanent use such as on small volume reservoirs. Standard material is annealed 6 stainless steel. Standard tubing collars and glands are provided unless otherwise specified. Hex Catalog No. psi Connections Length Size 60-2HF4-C-SS 0,000 O.D. TUIN HF4 60-2HF6-C-SS 0,000 O.D. TUIN HF6 " 60-2HF-C-SS 0,000 /6" O.D. TUIN HF Line Filters The line filters as shown utilize sintered stainless steel filter discs pc./set. Porosities are available as per the chart to the right. If not otherwise specified, 00 micron filter discs are supplied. (One micron = 0.00 millimeters). Material of bodies and end covers is annealed 6 stainless steel. Standard tubing glands and collars are provided unless otherwise specified. FLOW Micron Size Filter Hex vailable Catalog No. psi Connections Length Size F-5HF4-SS 0,000 HIH PRESSURE 5 60F-5HF6-SS 0,000 HIH PRESSURE 5 60F-5HF-SS 0,000 /6" HIH PRESSURE 5 all Check Valves all type check valves insure flow in one direction only. Material for bodies and covers is annealed 6 stainless steel, the ball is -4PH. Standard tubing glands and collars are provided unless otherwise specified. Catalog No. psi Connections Length Hex 60-4HF4-SS 0,000 HIH PRESSURE HF6-SS 0,000 HIH PRESSURE HF-SS 0,000 /6" HIH PRESSURE 5 FLOW Soft Seat Check Valves Soft seat check valves insure flow in one direction only and can be mounted in any position. These are highly reliable for both gas and liquid service. Standard O-ring (soft seat) material for the sealing surface is una-n (nitrile) with other materials including Teflon and Viton available on request. Temperature is limited by the choice of O-ring material. Material of all other parts is annealed 6 stainless steel. Standard glands and collars are provided unless otherwise specified. Catalog No. psi Connections Length Hex 0-4HF4-T-SS 20,000 HIH PRESSURE " 0-4HF6-T-SS 20,000 HIH PRESSURE " 0-4HF-T-SS 20,000 /6" HIH PRESSURE HF4-T-SS 0,000 HIH PRESSURE 4 /6" 60-4HF6-T-SS 0,000 HIH PRESSURE 4 /6" 60-4HF-T-SS 0,000 /6" HIH PRESSURE 5 /6" FLOW High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

142 Oil and as Products dapters Connect different sizes of tubing or tubing and pipe with our female-to-female couplings, female-to-male adapters, male-to-male adapters, reducer couplings and thermocouple adapters. For complete adapter information, see accessories section of full line catalog. Female to Female Female to Male Male to Male Tubing For sour gas applications, our tubing is annealed stainless steel, available for all standard valve and fitting sizes, and in any length specified. For sweet applications, HiP tubing is cold drawn, seamless and supplied in the hard condition (not annealed). Tubing is stocked in lengths of 8 to 22 feet but may be ordered in shorter lengths with no additional cutting charge. / 4 " / 8 " / 6 " Working Type of Catalog Tubing Size psi Connection Used Material Order Number O.D. x 0.08" I.D. 0,000 HIH PRESSURE (HF4) O.D. x I.D. 0,000 HIH PRESSURE (HF6) /6" O.D. x /6" I.D. 0,000 /6" HIH PRESSURE (HF) 6 SS 60-H4-6-SS 04 SS 60-H4-04-SS 6 SS 60-H6-6-SS 04 SS 60-H6-04-SS 6 SS 60-H-6-SS 04 SS 60-H-04-SS Coned and Threaded Nipples Connection-ready nipples are available in annealed and standard tubing for all valve and fitting sizes, and in any length specified. Nipples are not furnished with collars and glands, unless specified at time of order. Sour gas Length psi nipples are annealed 6 SS. 2 " 4" 6" 8" 0" Tubing Size (O.D. x I.D.) x 0.08" x 0,000 psi 0,000 psi 60-HM4-2.5-SS 60-HM6--SS 60-HM4-6-SS 60-HM6-6-SS 60-HM4-8-SS 60-HM6-8-SS 60-HM4-0-SS 60-HM6-0-SS 60-HM4-2-SS 60-HM6-2-SS /6" x /6" 0,000 psi 60-HM-4-SS 60-HM-6-SS 60-HM-8-SS 60-HM-0-SS 60-HM-2-SS.6

143 Wellhead auge and leed Valves Wellhead auge Valves One inlet and three outlet ports Packing located below stem threads Metal-to-metal seat for bubble tight shut-off Two piece non-rotating stem for standard service valves One piece stem for sour gas service Designed for line sampling or instrument calibration Inlet Outlet Catalog No. psi Service Connections Material Port Port 0VHF 0,000 Standard 6 SS 0VHF-SS 20,000 H 2 S /6" HIH PRESSURE nnealed 6 SS HF HF leed Valves Tee handle for easy operation Vent port tapped for safe plumbing Positive blow-out prevention on stem Metal-to-metal seat for bubble tight shut-off One piece hex construction for easy installation Compatible with standard PI test and gauge connections for 20,000 psi Designed for pressure bleeding Inlet Outlet Catalog No. psi Service Connections Material Port Port 0VHM 0,000 Standard /6 " HIH PRESSURE 6 SS 0VHM-SS 20,000 H 2 S x Female NPT nnealed 6 SS HM NF High Equipment Company 255 W. th Street Erie, P 6505 U.S.. Phone: (84) Fax: (84) Website:

144 Specialty Valves HiP produces many valves engineered for specific requirements and operating conditions. mong the specialty valves we offer are high temperature valves, micro control metering valves, pipe connection valves and male bottom connection valves. Our two most popular oil and gas specialty valves are described below. all Valves These valves provide shut-off of oil, liquid or gas flow through 20,000 psi. HiP ball valves are available in two way and three way configurations. Relief Valves Relief valves protect a system from over-pressure damage and failure. These valves are offered in pressures from,000 to 0,000 psi. Call for our 0 page catalog also available on CD Rom or see it on-line Represented by: High Equipment Company 255 W. th Street Erie, Pennsylvania 6505 U.S.. Phone: (84) Fax: (84) sales@highpressure.com Web Site: 04/08