Automatic Air Valves For raw and potable water For domestic and industrial sewage. Technical information for project planners and technicians

Size: px
Start display at page:

Download "Automatic Air Valves For raw and potable water For domestic and industrial sewage. Technical information for project planners and technicians"

Transcription

1 Automatic Air Valves For raw and potable water For domestic and industrial sewage Technical information for project planners and technicians

2 This page is intentionally left blank. 2

3 Table of contents 1. The purpose of aerating and air release 4 2. The points of aerating and air release 4 3. The ways of aerating and air release Ways of functioning Functioning of H-TEC air valve Model 987 (here type 2 ): Functioning of H-TEC air valve Model 986: 5 4. Types of air valves AV Model Air valve (single orifice / double orifice) AV Model Air valve (with cup seal) AVS Model 992 and Model 985 Air valve set Description of AVS Model 992 Description of AVS Model 985 (diaphragm) Installation above and below ground Accessories Surface box for below ground installation of air valve set Model Drainage element for air valve set Model Manhole cover and ring for air valve set Model Indicator plates for air valve Flushing and water tapping set (for air valve set Model 992) 8 5. Rating of valve size Rating of valve size Rating according to the flow performance diagram Installation Design of the connection Air valves in plants and manholes H-TEC air valve set, the logical further development of the air valve Shortening of air valve set Model 992 on site AVS - installation in existing manholes AVS - installation in ground water AVS - installation in flood areas AVS for waste water in ground water areas AV for water treatment plants AV for sterilization plants AV upstream and AV downstream of control valves AV in fire extinguishing systems AV upstream and downstream of reductions AV on waste water head pipes with automatic aeration AV on waste water vacuum pipes Insulation Pressure testing Functional testing and maintenance Reasons for maintenance Maintenance intervals Important maintenance work Maintenance of air valve set Model Maintenance of AVS Model Specification Air valves Air valve sets Air valve with stand pipe base Accessories Safety hints References 20 Page 3

4 1. The purpose of aerating and air release A water transport system is to be kept in an operating condition as stable as possible by taking the appropriate measures. Inclusions of air may have considerable negative effects on a pipeline system, such as: - longer running time pumps - higher energy input, shorter lifecycle of pumps - pressure fluctuations - reduction of flow - water hammer - pipe breakage - dry running of pumps The possibility of air entering into a pipeline system cannot be eliminated entirely. Already the air dissolved in the water proper may turn gaseous under certain pressure and temperature conditions. Even larger quantities of air will get into the pipeline system during maintenance work. These amounts of air will collect at certain points from where they have to be carried off by means of the appropriate valves (see below illustration). On the other hand, the lack of air may also lead to failures. Negative pressure will be created when water flows off too fast. This is mostly the case when pipes get drained or when pipe fractures occur, as well as in case of pumps being disconnected or downstream of quick-acting valves such as pipe fracture safety valves, where the flow of water is stopped abruptly, thus creating a negative pressure between the valve and the head of water being discharged. In this case sufficient air must be admitted to the pipeline through the air valve to limit the negative pressure and prevent damage to the pipeline. Moreover, there are accumulations of gas in waste water because of processes of decay and because of the deliberate blowing in of air. This implies the following requirements on air valves: - releasing minor amounts of air under operating pressure - releasing major amounts of air - admitting major amounts of air 2. The points of aerating and air release b RBS e a b c d c c a b The Air Valve Releases air from the pipeline: accumulations of air must be expected where the operating pressure is lower than in neighbouring pipeline sections: a) at each geodesic high point b) at each hydraulic high point c) at long ascending or descending pipe sections (recommended installation in intervals of approx. 0.5 mile/800 m) d) downstream of pumps and upstream of throttling points The Air Valve admits the required amount of air: at each spot of the pipeline where negative pressure must be expected, such as: e) downstream of quick-acting valves (pipe fracture safety valves PFSV) 4

5 3. The ways of aerating and air release 3.1 Ways of functioning Functioning of H-TEC air valve Model 987 (here type 2 ): Medium: potable water large cross section A = in 2 small cross section A = in 2 Releasing major amounts of air: During filling a pipeline releasing is effected via the large cross section. Releasing minor amounts of air: During operation of a pipeline releasing is effected via the small cross section. Aerating: During draining of a pipeline aeration is effected via the large cross section. Closing: After venting the valve closes automatically Functioning of H-TEC air valve Model 986: (This valve is also installed in air valve set Model 985) Medium: potable water and waste water A = in 2 A = in 2 Releasing major amounts of air: For filling a pipeline the whole venting cross section is available. Releasing minor amounts of air: During operation of a pipeline the venting cross section will be opened as far as necessary. Aerating: During draining of a pipeline aeration is effected via the whole aeration cross section. Closing: After venting the valve closes automatically. 5

6 Ventilation on highest level for water pipelines Improved air intake and release capacity Very high air release during operation continuously variable from 0 to 250 psi / 16 bar High-grade materials Easy maintenance Excellent UV resistance Only for air release or air intake - on request 350 psi / PN 25 - on request HaVent, the new performance generation Air release capacity during pipeline filling The air release capacity is gal/h even at a differential pressure of 1.45 psi / 0,1 bar Air release during operation The air release capacity over gal/h even at a differential pressure of 29 psi / 2 bar Air release capacity Q (m 3 /h) Air release capacity Q (m 3 /h) Differential pressure (bar) Differential pressure (bar) Aeration of pipeline The air intake capacity is approx gal/h at a negative pressure of psi / -0,1 bar Air intake capacity (m 3 /h) Negative pressure (bar) Possible connections Female thread 2 Male thread 2 Flange 4 Flange other nominal width on request! 6

7 Technical features Large outlet cross section for maximum air release and intake capacity during pipeline filling or draining A = 2.3 in2 Large air release cross section for reliable air release during operation Amax. = 0.3 in2 High-grade enclosure of aluminium Robust float of foamed plastics Flow control for optimized closing Valve mechanism No loose components Can be taken out in one piece Easy cleaning Easy exchange of wear parts if required 7

8 4. Types of Air Valves 4.1 Model Air Valve (single orifice / double orifice) Technical data: NP 2 NP 1 Test pressure (body) body 350 psi / 24 bar body 350 psi / 24 bar Operating pressure standard: psi / 0, bar standard: psi alternative: psi alternative: psi Opening cross section in 2 / in in 2 Max. air release capacity gal/h gal/h Connection female thread 2 or flange female thread 1 Insect protective grid yes no Weight 5.1 lbs / 2,35 kg 1.65 lbs / 0.75 kg Materials: Body POM Seat CuZn35Pb3As Float POM Valve gasket EPDM UV cap PE Insect protective grid ss316 NPT 2 : for large amounts of air NPT 1 : for small amounts of air On request: valve with ventilate-function only 4.2 Model Air Valve (with cup seal) Technical data: Test pressure (body) body 350 psi / 24 bar Operating range psi / 0 16 bar Opening cross section 0.75 in 2 / 480 mm 2 Max. air release capacity 230 m 3 /h / gal/h Connection female thread 2 or Flange 2-8 Media other flanges on request raw and potable water domestic and industrial waste water Features: infinitely variable operation from 0 bar onward seat not in contact with the medium suitable for parallel operation large orifice = prevents contamination = high air release capacity even under operating pressure Materials: Body fluidized bed epoxy powder coated alternatively SS 316 Body nut with screen POM / Float Valve body - bonnet O-ring 160 x 6 POM POM NBR Outlet elbow with strainer PE 100 / SS 316 Large amounts of air can be released under operating pressure due to infinitely variable operation! 8

9 4.3 Model 992 and Model 985 Air Valve Set Description of Air Valve Set, Model 992 Medium: potable water Description of Air Valve Set Model 985 (diaphragm) Medium: potable water and waste water hood with air vent slots additional elongated holes permit shortening by 100 mm stand pipe of stainless steel replaces the chamber and permits easy maintenance of the air valve cover chamber cylinder air valve insect protective grid operating rod H-TEC 2 air valve high-grade materials such as POM for the body, bronze for the seats and EPDM for sealings ensure corrosion resistance and permanent function (maintenance see item 6.) automatic shut-off function via initial spring tension ensures sealing even at 0 psi drain-off fitting shut-off facility with blank of stainless steel drain-off fitting (optional: can be closed via end fitting) BAIO spigot end 3 or flange 3 Both Air Valve Sets are available with flange 3 or BAIO spigot end. When using a BAIO spigot end please apply a dirt cover and locking ring (see specification of accessories) Installation above and below ground An Air Valve Set can be installed both above ground and below ground. The above ground type will be used wherever the valve shall be installed in open terrain. Pipe cover depth: above ground below ground Above ground (PCD) 2.5 ft / 0,75 m 3.3 ft / 1,00 m 4.1 ft / 1,25 m 4.9 ft / 1,50 m Below ground (PCD) 3.3 ft / 1,00 m 4.1 ft / 1,25 m 4.9 ft / 1,50 m 5.7 ft / 1,75 m L Flange 2.5 ft / 755 mm 3,5 ft / 1055 mm 4.3 ft / 1305 mm 5.1 ft / 1555 mm L Spigot end 2.7 ft / 815 mm 3.7 ft / 1115 mm 4.5 ft / 1365 mm 5.3 ft / 1615 mm 9

10 5. Rating of valve size 5.1 Rating of valve size In general, there are no limits to the pipeline diameter for operational air release. However, the accumulating amounts of air of a pipeline must be considered. They must not exceed the values specified in the flow diagram. As regards the required valve sizes and/or the free flow cross sections thereof the diagrams and calculations are based on the following assumptions: a) Release during filling of a pipeline: - The maximum water hammer during closing of the Air Valve is limited to 44psi/3 bar (which is equivalent to a max. flow rate of 10 inch/s in the pipeline) - The propagation rate of the pressure surges in the pipeline is assumed to be a = 4000 ft/s - The maximum flow rate in the free flow cross section of the Air Valve is limited to V E = 65 ft/s, since an excessive flow rate of the air might tear along the float of the Air Valve, thus closing the valve before the venting process proper. b) Aeration during drainage of a pipeline: - The absolute pressure in the pipeline is limited: p R = 13.8 psi/0,95 bar (= negative pressure of 0.7 psi 0,05 bar) - The contraction and friction value of the Air Valve is: µ = 0,52 Diagram 1: Filling the pipeline Diagram 2: Draining the pipeline required venting cross section A [ mm 2 ] inside diameter di of pipeline di [ mm ] max. adm. flow in the pipeline Q [ l / s ] Example of rating an Air Valve: For a pipeline with an inside diameter of d i = 12 the required size of the Air Valve shall be determined. Filling the pipeline: According to diagram 1 the free flow cross section in the air valve of a pipeline of d i = 12 must be at least 0.14 sq.inch. The flow in the pipeline must not exceed 4.8 gal/s. Draining the pipeline: According to diagram 2 the max. admissible flow on drainage of the pipeline is 11 gal/s at a free flow cross section in the valve of 0.14 sq.inch. This means that the H-TEC Air Valve Model (A = 960 mm 2 ) is able to manage the accumulating amount of air for aerating and/or draining of a pipeline do 12 under the specified assumptions. Since the above calculation may not be perfectly adapted to any pipe pressure situation possibly prevailing we recommend a comprehensive hydraulic calculation*. If, during filling of a pipelines, even larger amounts of air 10

11 must be expected, air release may also be performed manually. In this case a flushing and water tapping set is installed in the H-TEC Air Valve Set. However, other air release devices such as hydrants, may be used, too. 5.2 Rating according to the flow performance diagram The following diagram shows the interrelation between air release and aeration capacity of the valve at a given overpressure / negative pressure in the valve. Explanation by way of examples: a) Air release capacity of AV 1 at 73 psi / 5 bar: gal/h b) Air release capacity of AV at 0.7 psi / 0,05 bar: gal/h c) Air release capacity of AV at 73 psi / 5 bar: gal/h (as the big orifice is closed because of the air flow) d) Air intake capacity of AV : gal/h 11

12 6. Installation The points of installation are usually the relative or absolute high points of the pipeline. Because of the regular checks that are necessary they shall be easily accessible and not be situated in highly frequented traffic areas. However, the correct place of installation is more important (e.g. high point). 6.1 Design of the connection The nominal width of the supply line shall be as large as possible and should be equivalent to at least the valve size. This pipeline should run vertical from the pipeline to the valve. The dimension of the upstream shut-off valve, too, should be equivalent to at least the valve size. The largely dimensioned supply line to the valve serves the purpose of collecting the air carried along with the water from the main line at this point to be then discharged by the valve. For pipelines < 24 a sufficiently dimensioned ventilation chamber is required. Unless determined more precisely the ventilation chamber can be regarded as sufficiently dimensioned if its constructional height is equivalent to the diameter of the pipeline and its cross section is approximately half the cross section of the pipeline. Moreover, a central shut-off facility, a tee with air release and air intake facility and a lateral outlet for manual air intake and release as well as for depressurization before working at the air valve are required. The shut-off valve permits the installation and dismantling of the air release and intake facility as well as the manual air release facility without interruption of operation. Functional testing of the air intake and release facility and/or the floats and the manual air release facility with closed shut-off valve are possible. This shut-off valve must remain closed during pressure testing (see page 15) air valve manual air release facility shut-off facility Warning: Prior to installation of an Air Valve the pipeline must be flushed, since dirt and drilling chips might affect tightness (see also flushing and water tapping set). 6.2 Air Valves in plants and manholes Air Valves are installed in rooms or manholes. Inside the buildings care must be taken that the opening is sufficiently large to ensure an unobstructed flowing in and out of the air. By means of the integrated fine screen vermin and dirt are prevented from getting into the valve. As regards the design of the building care shall be taken that the residual water carried along in the process of air release can be discharged via a drainage device (drainage element). Warning: Prior to entering manholes make sure that sufficient fresh air is admitted! 12

13 6.3 H-TEC Air Valve Set, the logical further development of the air valve Advantages of H-TEC air valve set: low costs no access of manhole required integrated shut-off element maintenance work easy and time-saving No danger because of access to manhole! Conventional manhole H-TEC Air Valve Set 6.4 Shortening of Air Valve Set Model. 992 on site Both the above ground and the below ground version of the Air Valve Set may require shortening on site because of unexpected changes of the pipe cover depth. According to the drawing the operating tube (with the marking) and the stand pipe of stainless steel are cut by 4. Make sure to produce a straight cut edge. 6.5 Installation in existing manholes Air Valve Sets can also be installed in existing manholes. They are mounted on the pipeline instead of the old air valve. The manhole is backfilled with bulk material, thus avoiding future maintenance of the manhole. Moreover, the valve can be installed and dismantled from above for testing and maintenance. bulk material 13

14 6.6 Installation in ground water If rising ground water exceeds the level of the drainoff fitting dirty water may be sucked into the pipeline during aeration. The drain-off fitting must be closed or a back flow preventer must be installed. (This is not included in the standard scope of supply and must be ordered separately). In both cases it must be ensured by regular inspection of the Air Valve Set that no groundor rain water can accumulate in the Air Valve Set. If required,the water must be pumped out by means of a handpump. Warning: Penetrating ground or rain water may be sucked into the pipeline in case of negative pressure. Contamination and germs may be carried in. 6.7 Installation in flood areas In flood areas the length of the AVS shall be rated such that the hood with the air vent slots is approx 1.5 ft above the water level to be expected to prevent any dirty water from penetrating the Air Valve Set. The drain-off fitting must be closed. (This is not included in the standard scope of supply and must be prepared on site). Warning: Penetrating ground or rain water may be sucked into the pipeline in case of negative pressure. Contamination and germs may be carried in. 6.8 For waste water in ground water areas The drain-off fitting must be closed, e.g. by means of a pipe and end fitting, to prevent waste water from emerging into the soil. 14

15 6.9 For water treatment plants Automatic air release at the surge tank after water treatment with compressed air. For dimensioning, please consider the maximum air release amount at the given operating pressure of the Air Valve (see diagram). Because of its high air release capacity under operating pressure the valve Model 986 is best suited for this application. surge tank ARV compressed air from compressor 6.10 For sterilization plants In water sterilization plants the water is exposed to UV light. In this process air is set free that must be released at the highest point of the radiation plant. radiation cylinder ARV 6.11 Upstream and Air Valve downstream of controlvalves Control valves are very sensitive to airlocks in water. Therefore, depending on the operational conditions, it may be necessary to install an air release valve upstream of the control valve to ensure smooth operation. In this case a mere air release valve is recommended that is created by installing a nonreturn valve into the output pipe of the Air Valve (please order separa-tely). Warning: This nonreturn valve will reduce air release capacity! As at all throttle points in the pipeline system, air is set free downstream of control valves. Ideally, this air shall be removed from the pipeline while still in the manhole or building where the control valve is installed. Especially downstream of pipe fracture safety valves an aeration facility must be installed to prevent negative pressure as well as consequential damage to the pipelines caused by such negative pressure In fire extinguishing systems In fire extinguishing systems pumps are used that ensure sufficient delivery in case of emergency. These pumps will drag air into the pipeline that has to be removed again at the nearest high point. Before installation, please observe the applicable national regulations. 15

16 6.13 Upstream and downstream of reductions a) Upstream of reductions in the pipeline system, i.e. upstream of major contractions, air will accumulate that is not carried on (see curves for self-venting of pipelines. The Air Valve releases the accumulated air automatically. b) In case of flow from the smaller to the larger pipeline, too, venting may be necessary, e.g. for a descending pipeline, if the rate for self-venting is not reached On waste water head pipes with automatic aeration In some situations it is necessary to blow air into the pressure line via a compressor or pressure tank at regular intervals, in addition to normal pumping. In these cases we recommend the use of an air release stop, which is mounted at delivery (also possible later when already installed) on the valve outlet elbow. During normal pumping the air release stop is out of action. If, however, very high air quantities are supplied to the pressure line via a compressor or pressure tank,then the air release stop responds mechanically and closes the valve. After scavenging (air), the valve goes back to its normal operating state. For more detailed information please contact our applications engineering department On waste water vacuum pipes In waste water vacuum pipes only air release valves may be used. To this end a nonreturn valve shall be in stalled at the valve outlet side. Warning: This nonreturn valve will reduce air release capacity! 6.16 Insulation Valves installed directly on the main line are not very susceptible to freezing, since the water in the valve is heated by the water flowing in the main line. However, in case that an offset installation is necessary, i.e. in case of installation beside the main line, there is the danger of freezing. In this case both the supply line to the valve and the valve proper must be insulated. The valve in the Air Valve Set is protected from frost by inserting a disk cut to size and consisting of insulating material of approx. 2 in thickness with a hole in the centre (see drawing) is inserted halfway up the stand pipe. This disk must not seal tightly to ensure that air release and intake are not inhibited (approx. 10 holes with a diameter of 0.4 inch). The Air Valve in the manhole is protected from frost by lining the manhole walls and the manhole cover with insulating material (see drawing b). In case of waste water valves, too, insulation may be sensible. Though there is usually no danger of freezing, the depositing of grease at the wall of the Air Valve will be increased by temperature differences. 16

17 Drawing a Drawing b ø approx. 10 mm insulation insulation Air Valves installed in the open, for example below bridges, must also be insulated to be frost-resistant. In this case, insulation may be effected, for example, by backfilling the surface box with polystyrene chips. To discharge splash water a drainage pipe leading from the Air Valve into the open must be installed. 7. Pressure testing Prior to delivery H-TEC air valves are tested, including functional testing at max. operating pressure and body testing at 1,5 times the operating pressure. Prior to pressure testing of pipelines with Air Valve Set and/or Air Valve Sets the shut-off device must be closed, otherwise the pipeline may be vented during the pressure test, rendering the result of the pressure test useless. AV: AVS 992: AVS 985: Close shut-off device upstream of the valve. Take Air Valve out of the Air Valve Set the integrated shut-off device of the set closes automatically. Close shut-off device by means of half turn. 17

18 8. Functional testing and maintenance 8.1 Reasons for maintenance Almost all potable waters and waste waters carry along suspended particles and tend to sedimentation. In waste water there are also grease deposits and larger foreign bodies accumulating in the Air Valve. To avoid malfunctions caused by dirt Air Valves must be checked and maintained, if necessary, at regular intervals. 8.2 Maintenance intervals H-TEC recommends regular checks of Air Valves for potable water are demanded at least every 12 months. The exact maintenance interval depends on the quality of the water. The first maintenance will be done after 3 to 6 months after start-up and serves as a first reference value for further testing intervals. In case of waste water the maintenance intervals must be adapted to the conditions of the pipeline. Usually, the first Air Valves of a series of several valves are contaminated most heavily. There are no generally applicable rules for maintenance intervals. 8.3 Important maintenance work This information leaflet can show only the most important steps of maintenance. Please follow our maintenance instructions and comply with the safety hints. Prior to working at air valves the valve must be shut off via gate valve and unpressurized via an appropriate valve. Air valves represent one of the few automatic connections between the pipeline system and the ambience. Therefore, they have to be checked at regular intervals. (see also [2]) Maintenance of Air Valve Set Model 992 a b c Pull out valve by means of operating tube Simultaneously the foot valve closes the system at the bottom Open surface box Loosen screw a Take off hood Loosen screw b Take out spindle support c 0 Maintenance of Air Valve 2 : - Clean body and seats - Blow out valve bore by means of compressed air (see also sectional view item 3.1.1) Maintenance of Air Valve 1 : - Screw out seat and blow through - Clean valve seal (see also sectional view item 3.1.1) On start-up of the valve once again (perform above steps in reverse order) venting must be clearly audible (loud hiss) during screwing in of the spindle support. Otherwise the procedure has to be repeated. 18

19 8.3.2 Maintenance of Air Valve Set Model 985 All maintenance and service work can be done from the road surface, thus avoiding the dangers involved with entering manholes. The Air Valve can be flushed without being dismantled via the two flushing ports (5a / 5b). To this end hoses must be connected to the two flushing ports (5a / 5b) in such a way that the inside pressure is released safely after opening the ball valves (4 / 6). Flushing is performed by passing water from 5a to 5b, possibly adding some cleaning agent. If there are any foreign bodies in the valve that cannot be flushed out via the bottom flushing orifice, the valve should be dismantled, opened, and the foreign body be removed. To this end proceed as follows: 1. Take off the cover (1) from the chamber cylinder (2). Close the shut-off valve by means of the offset operating tube (3) by a half turn (clockwise). The operating tube must be offset by 180 before! Warning: Even after closing the shut-off valve the air valve is pressurized, therefore open the ball valve (4) on the lateral flushing pipe carefully and only after mounting a hose at the flushing port provided for this purpose (5b). Discharge any emerging waste water safely. Dismantle the 3/2-way ball valve (6). To this end loosen the screwed union a 6 5b 4 2. Pull the operating tube (3) upward and out of the air valve set. Turn the valve (7) counterclockwise until the bayonet coupling (8) is loosened. Pull the valve upward and out of the chamber cylinder (2) at the two eye bolts (9) by means of a suitable lifting tool. Any residual water is discharged via the drainage device. If this is not desired, install an end fitting (13) and pump out the chamber Open the body screws (10). Clean the valve inside (use a cleaning solution, if required, in case of persistent dirt, let the agent work itself in for a while, before cleaning by means of a brush). Screw the valve bonnet (11) back on again, making sure that the toroidal sealing ring is fitting properly. Prior to installation of the Air Valve clean all sealing surfaces Put the valve (7) onto the bayonet coupling from above and lock it clockwise. Put the 3/2-way ball valve (6) back in place and tighten the screwed unions manually until the connections are tight. Put on the operating tube (3). Close the ball valve of the lower flushing orifice (4). Slowly open the shut-off valve (12) below the air valve (counterclockwise). After opening offset the operating tube again by 180 (safety function against automatic unlocking of the Air Valve). Visual inspection of all connections and flushing orifices

20 9. Specification 9.1 Air Valves Air Valves Model 987 Specification: Air Valve For Water Service ( #987; 1 ) The valve shall be a combination air/vacuum single orifice automatic air release valve with 1 connection to the pipeline. The valve shall be of corrosion free materials, single orifice for allow air to escape and enter in the event of a vacuum condition. The valve shall be of one piece body design. Body and float shall be Delrin (Polyoximethylene, POM). The seat and valve plug made of CuAl10. The valve sealing is rubber made of EPDM. The valve shall have a protection cap of PE. Air and vacuum valves shall be manufactured by Hawle Specification: Air Valve For Water Service ( #987; 2 ) The valve shall be a combination air/vacuum double orifice automatic air release valve with 2 connection to the pipeline. The valve shall be of one piece body design. The internal parts shall have a small orifice within tripod for small air discharge and a big orifice within bonnet of base housing for main air discharge and allow air to enter in the event of a vacuum condition. The material of the body and the flow shall be Delrin ( Polyoximethylene, POM ). The valve sealing is rubber made of EPDM. The valve shall have a protection cap of PE. Air and vacuum valves shall be manufactured by Hawle Air Valve for Sewage ans Water Service 986 Specification: Combination Air Valves shall conform to the following: Automatic Air and Vacuum Valves shall be infinitely variable automatic air and vacuum valves designed to allow escape of air for a operating range starting from pressure range: 0,0 through 250 psi ( 0 17,2 bar ), close watertight when liquid enters the valve even when the fluid is rising without pressure ( no minimum operating pressure required), allow air to enter in the event of a vacuum, and soft working behavior as water hammer inhibition realized by roll-on diaphragm and spring mechanism. When the sealing device of the valve is closed an air cushion is trapped between the fluid and sealing area, a mud deflector made of PE allows no contact between fluid and sealing area. The valve body and spindle spring shall be stainless steel grade 316Ti, designed to facilitate disassembly for cleaning and maintenance. The float shall be Delrin ( Polyoximethylene, POM ); the valve seat and all working parts shall be of corrosion resistant materials. Valves shall be equipped with the necessary attachments, including ball valve, to permit back flushing after installation without dismantling the valve. Valves shall be recommended by the manufacturer for wastewater service. Air and vacuum valves shall be manufactured by Hawle. 20

21 9.2 Air Valve sets Automatic Air Valve Set ( #992 ) Valve with Shaft for Underground Installation Automatic air valve with standpipe of stainless steel (replacing a shaft), BAIO spigot end or flanged connection drilled, of Ductile Iron (GJS-400), high-quality corrosion protection by fluidized bed epoxy powder coating inside and outside. The valve shall be a combination air/vacuum double orifice automatic air release valve. The valve shall be of one piece body design. The internal parts shall have a small orifice within tripod for small air discharge and a big orifice within bonnet of base housing for main air discharge and allow air to enter in the event of a vacuum condition. The material of the body and the flow shall be Delrin ( Polyoximethylene, POM ). The valve sealing is rubber made of EPDM. Standpipe of stainless steel suitable for above ground and underground installation, standpipe with drain-off fitting. Air and vacuum valves shall be manufactured by Hawle. Air Valve Set for Operating Range psi / 0 17,2 bar ( #985 ) Automatic Air and Vacuum Valves shall be infinitely variable automatic air and vacuum valves designed to allow escape of air for a operating range starting from pressure range: 0,0 through 250 psi ( 0 17,2 bar ), close watertight when liquid enters the valve even when the fluid is rising without pressure ( no minimum operating pressure required), allow air to enter in the event of a vacuum, and soft working behaviour as water hammer inhibition realized by roll-on diaphragm and spring mechanism. When the sealing device of the valve is closed an air cushion is trapped between the fluid and sealing area, a mud deflector made of PE allows no contact between fluid and sealing area. The valve body and spindle spring shall be stainless steel grade 316Ti, designed to facilitate disassembly for cleaning and maintenance. The float shall be Delrin ( Polyoximethylene, POM ); the valve seat and all working parts shall be of corrosion resistant materials. Valves shall be equipped with the necessary attachments, including ball valve, to permit back flushing after installation without dismantling the valve. Valves shall be recommended by the manufacturer for wastewater service. The air valve set is provided with a PE shaft replacing a manhole, a shut-off device with a steel plate of hard-rolled stainless steel and straight-through bore when open, two maintenance outlets with hose connection and ball valve, lateral outlet for waste air with PE elbow as swivelling device equipped with additional protection grid, drain-off fitting at the shaft bottom. After closing the shut-off device by integrated operating tool and removal of the upper ball valve the air valve can be taken out of the shaft for maintenance purposes. Valves shall be recommended by the manufacturer for wastewater service. Air and vacuum valves shall be manufactured by Hawle 21

22 Air Valve Set Model 985 with spigot end Air Valve Set Model 985 with flange Air Valve Set Model 985 with PE tail Medium: raw and potable water, domestic and industrial waste water Operating range: 0 16 bar Component 80 Material 1 Spigot end 80 GGG 40, fluidized bed epoxy powder coated 2 Shut-off facility GGG 40, fluidized bed epoxy powder coated 3 Air Valve steel, St. 37 fluidized bed epoxy powder coated 4 Chamber cylinder PE 5 Cover PE 6 Three-way ball valve PVC 7 Hose coupling PA 6 GF 25 8 Ball valve stainless steel 9 Operating rod square steel St. 37 fluidized bed epoxy powder coated 10 Bottom plate sheet steel St. 37 fluidized bed epoxy powder coated 11 Drain-off fitting GGG 40, fluidized bed epoxy powder coated Accessories 12 End fitting (please observe surcharge!) POM 13 Manhole cover GGG 40, bituminized Manhole ring GG 24, bituminized Drawing representing Air Valve Set with BAIO spigot end

23 Automatic Air Valve Set Model 992 with spigot end Automatic Air Valve Set Model 992 with flange Automatic Air Valve Set Model 992 with PE tail Medium: potable water Operating pressure: PSI (0,1 6 bar) and PSI (0,1-6 bar) Component Material 1.1 Inlet flange GGG Fitting GGG O-ring NBR Grip ring POM 1.3 O-ring NBR 1.4 Sealing flange Rg Foot valve POM 1.6 Spring case MS Pressure spring stainless steel 1.8 Hexagon screw M 10 x 35 DIN 933 stainless steel 2.1 Bonnet POM 2.2 O-ring NBR 2.3 Seat CuZn35Pb3As / EPDM Hexagon screw stainless steel 2.4 Locking plate stainless steel 2.5 Locknut MS Bottom part of body POM Air valve support POM Float bottom part POM Ballast EPDM Float top part POM / EPDM Sealing screw stainless steel Fan type lock washer stainless steel Sealing cover POM Seat for sealing cover EPDM O-ring NBR 2.9 O-ring NBR 2.10 Hexagon nut stainless steel 2.11 Washer stainless steel 2.12 Hexagon socket bolt stainless steel 2.13 O-ring NBR 2.14 Insect protective grid stainless steel 3 Operating tube stainless steel 4 Centring cap GGG Hexagon screw M 8 x 10 DIN 931 stainless steel 5 Stand pipe stainless steel 6 Lock ring GGG 40 7 Hexagon bolt M 16 x 50 DIN 931 stainless steel 8 Hexagon nut M 16 DIN 934 stainless steel 9 Washer stainless steel 10 Sealing EPDM 11 Cover EPDM 12 Spindle support GGG Operating screw Ms Hood PE 15 Hexagon screw M 8 x 60 DIN 931 stainless steel 16 Washer stainless steel 17 Drain pipe PE The following abbreviations are used: AV = air valve AVS = air valve set ARV = air release valve 17

24 Edition September Subject to change 1700 Enterprise Way, Suite 116 Marietta, GA Phone Fax:

Water. VAG DUOJET Automatic Air Valve Single-chamber type PN 10/16/25/40 - DN KAT-A 1912

Water. VAG DUOJET Automatic Air Valve Single-chamber type PN 10/16/25/40 - DN KAT-A 1912 Water VAG DUOJET Automatic Air Valve Single-chamber type Product characteristics and benefits Resilient seated With flange end acc. to EN 1092-2 Single chamber air valve in compact design Very high discharge

More information

Combination Air Valve

Combination Air Valve Combination Air Valve For Sewage and Wastewater Model C50 Installation, Operation and Maintenance Manual (IOM) Table of Contents General... Page 2 Safety... Page 2 Operational Data... Page 3 Materials

More information

Mounting and Operating Instructions EB 3007 EN. Self-operated Pressure Regulators. Differential Pressure Regulators (opening) Type Type 42-25

Mounting and Operating Instructions EB 3007 EN. Self-operated Pressure Regulators. Differential Pressure Regulators (opening) Type Type 42-25 Self-operated Pressure Regulators Differential Pressure Regulators (opening) Type 42-20 Type 42-25 Type 42-20 Differential Pressure Regulator Type 42-25 Differential Pressure Regulator Mounting and Operating

More information

DAV - WP DAV - WP. Wastewater Air Valves. Product Catalogue. (Wastewater Air Valves) DAV - WP

DAV - WP DAV - WP. Wastewater Air Valves. Product Catalogue. (Wastewater Air Valves) DAV - WP DAV - WP Wastewater Air Valves DAV - WP (Wastewater Air Valves) Product Catalogue DAV - WP DAV Series??? DAV-WP General DAV-WP Wastewater Air Valves The DAV-WP valve has been designed for efficient discharge

More information

Differential Pressure Regulator Type Type 45-6 (0.1 to 1 bar, DN 15) Mounting and Operating Instructions EB 3226 EN

Differential Pressure Regulator Type Type 45-6 (0.1 to 1 bar, DN 15) Mounting and Operating Instructions EB 3226 EN Differential Pressure Regulator Type 45-6 Type 45-6 (0.1 to 1 bar, DN 15) Mounting and Operating Instructions EB 3226 EN Edition March 2008 Contents Contents Page 1 Design and principle of operation...................

More information

Wastewater combination air valve in stainless steel AISI 316 Mod. SCS

Wastewater combination air valve in stainless steel AISI 316 Mod. SCS Wastewater combination air valve in Mod. SCS The air valve guarantees the proper operation of sewage/industrial lines allowing the entrance of large quantity of air in case of pipe bursting or draining,

More information

Installation, operation & maintenance manual - original version

Installation, operation & maintenance manual - original version Installation, operation & maintenance manual - original version AVK gate valves for water and wastewater Series 01, 02, 06, 12, 15, 18, 20, 26, 32, 33, 36, 38, 50, 55 and 636 COPYRIGHT AVK GROUP A/S 2018

More information

DAV Series. DAV-MH Air Release & Vacuum Break Valves

DAV Series. DAV-MH Air Release & Vacuum Break Valves DAV-MH Air Release & Vacuum Break Valves ISO 9 AVFI Pty Ltd 4 Enterprise Drive Bundoora Vic 383 p: 3 8467 f: 3 8467 99 e: avfi@avfi.com.au w: www.avfi.com.au General DAV-MH Air Release and Vacuum Break

More information

Bermad Pressure Reducing. Model: 42T

Bermad Pressure Reducing. Model: 42T Bermad Pressure Reducing Pilot Operated Pressure Control Valve Model: 42T Installation Operation Maintenance Manual (IOM) REV. 27.7.17 Page 1 of 12 Safety First BERMAD believes that the safety of personnel

More information

Mounting and operating instructions EB 2530 EN. Self-operated Pressure Regulator. Pressure Reducing Valve Type M 44-2

Mounting and operating instructions EB 2530 EN. Self-operated Pressure Regulator. Pressure Reducing Valve Type M 44-2 Self-operated Pressure Regulator Pressure Reducing Valve Type M 44-2 Type M 44-2, connection G 1 4, K VS = 0.15 Type M 44-2, connection G 1, K VS = 6 Fig. 1 Type M 44-2 Pressure Reducing Valve Mounting

More information

Mounting and Operating Instructions EB 2558 EN. Self-operated Pressure Regulators. Type Pressure Build-up Regulator

Mounting and Operating Instructions EB 2558 EN. Self-operated Pressure Regulators. Type Pressure Build-up Regulator Self-operated Pressure Regulators Type 2357-31 Pressure Build-up Regulator with safety function and integrated excess pressure valve Type 2357-31 with non-return unit at port C Ports A and B with soldering

More information

THE MF-400 SERIES. Operating and Service Manual. Series includes all variants of MF-400/401

THE MF-400 SERIES. Operating and Service Manual. Series includes all variants of MF-400/401 THE MF-400 SERIES Operating and Service Manual Series includes all variants of MF-400/401 Issue A October 2013 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 4. Special

More information

Pressure Reducing Valve DMV 755

Pressure Reducing Valve DMV 755 Pressure Reducing Valve DMV 755 Nominal size DN 10 50 Nominal size 3/8 2 Nominal pressure PN 10 bar Features pressure setting range 1 to 9 bar control valve for reliable reduction of system pressures to

More information

Model GP PRESSURE REDUCING VALVE Installation & Operation Manual

Model GP PRESSURE REDUCING VALVE Installation & Operation Manual Model GP-2000 PRESSURE REDUCING VALVE Installation & Operation Manual Please read this bulletin thoroughly before using the pressure reducing valve, so that you may do so correctly and safely. Please carefully

More information

Mounting and Operating Instructions EB 3017 EN. Self-operated Regulators

Mounting and Operating Instructions EB 3017 EN. Self-operated Regulators Self-operated Regulars Flow and Differential Pressure Regular Type 42-37 Flow and Differential Pressure or Flow and Pressure Regular Type 42-39 Type 42-37 Type 42-39 Fig. 1 Flow and differential pressure

More information

Flanged pressure reducer/stabilizer VRCD

Flanged pressure reducer/stabilizer VRCD Flanged pressure reducer/stabilizer VRCD 2 This unit reduces and stabilizes the upstream pressure by operating on its load losses with a constant downstream pressure irrespective of the rate of flow value.

More information

DS05C,D,G Dial Set Pressure Regulating Valves

DS05C,D,G Dial Set Pressure Regulating Valves DS05C,D,G Dial Set Pressure Regulating Valves APPLICATION The Honeywell DS05C,D,G Dial Set Pressure Regulating Valve is a high quality pressure regulating valve that maintains a constant outlet pressure

More information

Pressure Reducing Valve DMV 750 set range: bar

Pressure Reducing Valve DMV 750 set range: bar Pressure Reducing Valve DMV 750 set range:.0-6.0 bar Advantage pressure setting possible at any time, also during operation hermetically sealed by valve diaphragm high level of operating safety and long

More information

Horizontal Bladder Tanks

Horizontal Bladder Tanks DATA SHEET Horizontal Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)

More information

APCO ARV CLEAN WATER AIR RELEASE VALVES. Model 50A

APCO ARV CLEAN WATER AIR RELEASE VALVES. Model 50A APCO ARV CLEAN WATER AIR RELEASE VALVES Model 50A Instruction D12013 February 2017 Instructions These instructions provide installation, operation and maintenance information for APCO ARV Clean Water Air

More information

VAG DUOJET Automatic Air Valve

VAG DUOJET Automatic Air Valve Operation and Maintenance Instructions VAG DUOJET Automatic Air Valve KAT-B 1912 Edition2 05-10 Contents 1 General 3 1.1 Safety 3 1.2 Proper use 3 1.3 Identification 3 VAG reserves the right to make technical

More information

TECHNICAL DATA. Page 1 of 12

TECHNICAL DATA. Page 1 of 12 Page 1 of 12 1. DESCRIPTION The Viking Regulating Valve is a direct-acting, single-seated, spring-loaded diaphragm valve. When installed as a pilot regulating valve on a Viking Model H or J Flow Control

More information

TECHNICAL DATA. Pressure Regulation 531a. April 24, 2009

TECHNICAL DATA. Pressure Regulation 531a. April 24, 2009 April 24, 29 Pressure Regulation 531a 1. DESCRIPTION The Viking Regulating Valve is a direct-acting, single-seated, spring-loaded diaphragm valve. When installed as a pilot regulating valve on a Viking

More information

Description. Functions. Technical data. Applications. Tests. On-Off 2 levels float control valve, closing at high level and opening at low level.

Description. Functions. Technical data. Applications. Tests. On-Off 2 levels float control valve, closing at high level and opening at low level. DN 0 to 1000 - Serie K3 0 On-Off levels float control valve, closing at high level and opening at low level. Functions Prevents overflowing and closes at a constant and adjustable high level. Remains closed

More information

Mounting and Operating Instructions EB 2555 EN. Self-operated Pressure Regulators. Pressure Reducing Valves Type 50 ES Type 50 EM.

Mounting and Operating Instructions EB 2555 EN. Self-operated Pressure Regulators. Pressure Reducing Valves Type 50 ES Type 50 EM. Self-operated Pressure Regulators Pressure Reducing Valves Type 50 ES Type 50 EM Type 50 ES Type 50 EM Fig. 1 Pressure reducing valves Mounting and Operating Instructions EB 2555 EN Edition November 2011

More information

Pressure reducing valves Index

Pressure reducing valves Index Index General information page Introduction 506 General introduction 507 for a steam plant 509 Product information BSP thread page Brass 510 ; BSP female thread 511 ; BSP male thread 513 Stainless steel

More information

Installation, Operating and Maintenance Manual Overflow Regulator Type 94/ 94 E

Installation, Operating and Maintenance Manual Overflow Regulator Type 94/ 94 E Installation, Operating and Maintenance Manual Overflow Regulator Type 94/ 94 E Table of content 1. General information on installation, operating and maintenance instructions 1.1 Hazard notices 1.2 Qualified

More information

Model MTB-ASME Vertical Bladder Tanks

Model MTB-ASME Vertical Bladder Tanks DATA SHEET Model MTB-ASME Vertical Bladder Tanks Features n UL Listed for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure (design pressure)

More information

D05 Pressure Regulating Valves

D05 Pressure Regulating Valves D05 Pressure Regulating Valves FEATURES PRODUCT DATA Noncorroding unitized cartridge contains all working parts and is easily replaceable. Includes built-in strainer and thermal bypass. Balanced seat construction

More information

Vertical Bladder Tanks

Vertical Bladder Tanks DATA SHEET Vertical Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)

More information

MEGR-1627 Instruction Manual

MEGR-1627 Instruction Manual MEGR-1627 HIGH FLOW GAS REGULATOR Instruction Manual- Look Inside For: Description Installation Remote Vent Line Installations Startup and Adjustment Shutdown Maintenance Body Maintenance Procedures Diaphragm

More information

Model MTB-ASME Vertical Bladder Tanks

Model MTB-ASME Vertical Bladder Tanks DATA SHEET Model MTB-ASME Vertical Bladder Tanks Features n UL Listed for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure (design pressure)

More information

I T T Pressure Reducing Valve WARNING INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

I T T Pressure Reducing Valve WARNING INSTALLATION, OPERATION, AND MAINTENANCE MANUAL INSTALLATION, OPERATION, AND MAINTENANCE MANUAL I-867-4T 867-4T Pressure Reducing Valve HANG THESE INSTRUCTIONS ON THE INSTALLED VALVE FOR FUTURE REFERENCE WARNING Read and understand all instructions

More information

4 IN. BALL LAUNCHER Engine Mounted / PTO Driven

4 IN. BALL LAUNCHER Engine Mounted / PTO Driven 4 IN. BALL LAUNCHER Engine Mounted / PTO Driven OPERATOR S PARTS and MAINTENANCE MANUAL 2006 EDITION BL-MAN-4EN Creation Revision date: 10MAR06 date: by: Ivon LeBlanc by: Table of Contents Table of Contents...

More information

Type S301 & S302 Gas Regulators INTRODUCTION INSTALLATION. Scope of Manual. Description. Specifications. Type S301 and S302. Instruction Manual

Type S301 & S302 Gas Regulators INTRODUCTION INSTALLATION. Scope of Manual. Description. Specifications. Type S301 and S302. Instruction Manual Fisher Controls Instruction Manual Type S301 & S302 Gas Regulators October 1981 Form 5180 WARNING Fisher regulators must be installed, operated, and maintained in accordance with federal, state, and local

More information

1805 Series Relief Valves

1805 Series Relief Valves Instruction Manual Form 1211 1805 Series October 2011 1805 Series Relief Valves! WARNING Failure to follow these instructions or to properly install and maintain this equipment could result in an explosion

More information

Model MTB-ASME Horizontal Bladder Tanks

Model MTB-ASME Horizontal Bladder Tanks DATA SHEET Model MTB-ASME Horizontal Bladder Tanks Features n UL Listed and FM Approved for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure

More information

THE HF-300 SERIES. Operating and Service Manual. Series includes all variants of HF-300/301

THE HF-300 SERIES. Operating and Service Manual. Series includes all variants of HF-300/301 THE HF-300 SERIES Operating and Service Manual Series includes all variants of HF-300/301 Issue A July 2015 1 TABLE OF CONTENTS 1. Description... 3 2. Installation... 3 3. Operation... 4 3.1. Spring Loaded...

More information

Model 420-HY Pressure Regulating Hydrant Valve

Model 420-HY Pressure Regulating Hydrant Valve Model 420-HY Pressure Regulating Hydrant Valve INSTALLATION OPERATION MAINTENANCE 1. Safety First BERMAD believes that the safety of personnel working with and around our equipment is the most important

More information

Model: 720-UL INSTALLATION OPERATION MAINTENANCE. Bermad Pressure Reducing Valve IOM. Model: FP -720-UL Sizes: 2"-12" BERMAD. Application Engineering

Model: 720-UL INSTALLATION OPERATION MAINTENANCE. Bermad Pressure Reducing Valve IOM. Model: FP -720-UL Sizes: 2-12 BERMAD. Application Engineering Bermad Pressure Reducing Valve Model: 720-UL INSTALLATION OPERATION MAINTENANCE Application Engineering BERMAD 1. Safety First BERMAD believes that the safety of personnel working with and around our equipment

More information

Model GPR Primary Pressure Regulating Valve. Instruction Manual

Model GPR Primary Pressure Regulating Valve. Instruction Manual Model GPR-2000 Primary Pressure Regulating Valve Instruction Manual Please read this instruction manual thoroughly before using the primary pressure regulating valve, so that you may do so correctly and

More information

MUELLER. Mega-Lite Drilling Machine. Reliable Connections. table of contents PAGE. Equipment 2. Operating Instructions 3-4. Parts Information 5

MUELLER. Mega-Lite Drilling Machine. Reliable Connections. table of contents PAGE. Equipment 2. Operating Instructions 3-4. Parts Information 5 operating Instructions manual MUELLER Mega-Lite Drilling Machine table of contents PAGE Equipment 2 Operating Instructions 3-4 Parts Information 5 Travel Charts 6-11! WARNING: 1. Read and follow instructions

More information

TECHNICAL DATA CAUTION

TECHNICAL DATA CAUTION Page 1 of 12 1. DESCRIPTION The Viking Model C-2 Pilot Pressure Regulating Valve is a direct-acting, single-seated, spring-loaded diaphragm valve. When installed as a pilot regulating valve on a Viking

More information

776 Cryogenic Safety Valve

776 Cryogenic Safety Valve 776 Cryogenic Safety Valve INTRODUCTION 776 Cryogenic Safety Valve The effects of exceeding safe pressure levels in an unprotected pressure vessel or system, can have catastrophic effects on both plant

More information

MODEL 200 KNIFE GATE VALVES INSTALLATION & MAINTENANCE MANUAL

MODEL 200 KNIFE GATE VALVES INSTALLATION & MAINTENANCE MANUAL MODEL 200 KNIFE GATE VALVES INSTALLATION & MAINTENANCE MANUAL Index 1. List of components / General arrangement 2. Description 3. Handling 4. Installation 5. Actuators / Operation 6. Maintenance a. Changing

More information

WW-730. Pressure Sustaining/Relief Control Valve

WW-730. Pressure Sustaining/Relief Control Valve WW-730 Pressure Sustaining/Relief Control Valve Installation Operation & Maintenance Page 1 of 6 1. DESCRIPTION The Model 730 Pressure Relief / Sustaining Valve is an automatic control valve designed to

More information

Pressure relief valve DHV 712 DN 65-80: 0,5-10 bar, DN : 0,3-4 bar, DN 100: 0,5-6 bar

Pressure relief valve DHV 712 DN 65-80: 0,5-10 bar, DN : 0,3-4 bar, DN 100: 0,5-6 bar Pressure relief valve DHV 7 DN 5-80: 0,5-0 bar, DN 5-00: 0, - bar, DN 00: 0,5 - bar Advantage for high pressure stability reliable reduction of pressure peaks and pulsations pressure setting possible at

More information

Types 749B and R130 Changeover Manifolds

Types 749B and R130 Changeover Manifolds Instruction Manual MCK-1179 Types 749B and R130 June 2012 Types 749B and R130 Changeover Manifolds TYPE HSRL-749B TYPE 64SR/122 TYPE R130/21 TYPE 749B/21 Figure 1. Changeover Manifolds and Regulator Assemblies

More information

Components for air preparation and pressure adjustment. OUT port position ( ) connected Rear side. of IN port. Air tank. directly.

Components for air preparation and pressure adjustment. OUT port position ( ) connected Rear side. of IN port. Air tank. directly. Components preparation and pressure adjustment ABP Overview ABP is a component that enables boosting by s only up to twice primary pressure (.0MPa max.) in combination with using air tank but not using

More information

Pressure and Flow Control Valves DBGM, German and European Patents

Pressure and Flow Control Valves DBGM, German and European Patents Pressure and Flow Control Valves DBGM, German and European Patents Absolutely Reliable Pressure and Flow Control In water mains of sizes DN 50 to DN 150, ERHARD Control Valves in straight or angle pattern

More information

DAV - MP DAV - MP. Metallic-Shield Air Valves. Product Catalogue. (Metallic-Shield Air Valves) DAV - MP

DAV - MP DAV - MP. Metallic-Shield Air Valves. Product Catalogue. (Metallic-Shield Air Valves) DAV - MP DAV - MP Metallic-Shield Air Valves Product Catalogue DAV - MP DAV - MP (Metallic-Shield Air Valves) Edition 9/ DAV Series DAV-MP Overview General The presence of trapped air in a pressurized pipeline

More information

OPERATING AND MAINTENANCE MANUAL

OPERATING AND MAINTENANCE MANUAL Series 4300 Engineered Performance TABLE OF CONTENTS 0 INTRODUCTION 1 1 Scope 1 2 Description 1 3 Specifications 1 0 INSTALLATION 1 1 Mounting 1 2 Piping 1 1 Connecting Process Pressure 2 2 Vent Connections

More information

Installation Operation Maintenance. Bermad Level Control Valve with Modulating Horizontal Float Pilot valve One Way Flow IOM.

Installation Operation Maintenance. Bermad Level Control Valve with Modulating Horizontal Float Pilot valve One Way Flow IOM. Bermad Level Control Valve with Modulating Horizontal Float Pilot valve One Way Flow Model: FP 450-80 Installation Operation Maintenance PAGE 1 OF 5 1. Safety First BERMAD believes that the safety of personnel

More information

Combination Air Valve Model

Combination Air Valve Model Combination Air Valve Model Model C10 /C11 Installation, Operation and Maintenance Manual (IOM) Table of Contents General...Page 2 Safety...Page 2 Operational Data...Page 3 Materials and Connections...Page

More information

Ball Float Steam Trap UNA 43 PN 16/CL 125/JIS 10K UNA 46 PN 40/CL 150/CL 300/JIS 10K/JIS 20K DN 80, 100, 150, 3", 4", 6"

Ball Float Steam Trap UNA 43 PN 16/CL 125/JIS 10K UNA 46 PN 40/CL 150/CL 300/JIS 10K/JIS 20K DN 80, 100, 150, 3, 4, 6 Data Sheet 819584-00 Issue Date: 01/17 Ball Float Steam Trap UNA 43 PN 16/C 125/JIS 10K UNA 46 PN 40/C 150/C 300/JIS 10K/JIS 20K DN 80, 100, 150, 3", 4", 6" UNA 43 hl, UNA 46 hl UNA 43 v, UNA 46 v with

More information

3/8" Dr. Air Butterfly Impact Wrench

3/8 Dr. Air Butterfly Impact Wrench 8192106 3/8" Dr. Air Butterfly Impact Wrench Owner s Manual Read and understand all instructions before use. Retain this manual for future reference. Specifications Construction: Polished aluminum and

More information

Assembly Drawing: W-311B-A01, or as applicable Parts List: W-311B-A01-1, or as applicable Special Tools: , , &

Assembly Drawing: W-311B-A01, or as applicable Parts List: W-311B-A01-1, or as applicable Special Tools: , , & REDQ Regulators Model 411B Barstock Design Powreactor Dome Regulator OPERATION AND MAINTENANCE Contents Scope..............................1 Installation..........................1 General Description....................1

More information

AIR RELIEF VALVES NETWORK PROTECTION

AIR RELIEF VALVES NETWORK PROTECTION AIR RELIEF VALVES NETWORK PROTECTION AIR RELIEF VALVES NETWORK PROTECTION Problems caused by the presence of air in networks may be solved by fitting suitable equipment. BELGICAST can supply a wide range

More information

Instruction presentation Special valves

Instruction presentation Special valves Instruction presentation Special valves 1 Special Valves 2 Special Valves Index of contents 1. Overview special valves 2. Description Gauge Guard 3. Description Water Jet Pumps 4. Description Venting and

More information

V43 Pressure Actuated Water Regulating Valve

V43 Pressure Actuated Water Regulating Valve FANs 125, 121 Product/Technical Bulletin V43 Issue Date 0996 V43 Pressure Actuated Water Regulating Valve The V43 Pressure Actuated Water Regulating Valves are designed to regulate water flow for water-cooled

More information

Installation and operating instructions KEMPER Backflow Preventer BA Figure 361

Installation and operating instructions KEMPER Backflow Preventer BA Figure 361 Installation and operating instructions KEMPER Backflow Preventer BA Figure 361 1. Prerequisites for installation Install the backflow preventer in frost-free areas only! DIN EN 1717, DIN 1988 Comply with

More information

299H Series. Introduction. P.E.D. Categories. Specifications. Installation. Warning. Installation Guide English September 2012

299H Series. Introduction. P.E.D. Categories. Specifications. Installation. Warning. Installation Guide English September 2012 Installation Guide English September 2012 299H Series Introduction This Installation Guide provides instructions for installation, startup, and adjustment of 299H Series regulators. To receive a copy of

More information

DS06D,G Dial Set Pressure Regulating Valve

DS06D,G Dial Set Pressure Regulating Valve DS06D,G Dial Set Pressure Regulating Valve PRODUCT DATA FEATURES APPLICATION Built-in, factory-calibrated outlet pressure adjustment dial. Noncorroding unitized cartridge contains all working parts and

More information

Eaton Filtration, LLC

Eaton Filtration, LLC Eaton Filtration, LLC 900 Fairmount Avenue, Elizabeth, NJ 07207 Phone: 908-787-1000 Fax: 908-351-7893 E-Mail: filtration@eaton.com Web: www.filtration.eaton.com Installation, Operation & Service Manual

More information

1200B2 Series Service Regulators. Instruction Manual

1200B2 Series Service Regulators. Instruction Manual 00B Series Service Regulators Instruction Manual 00B Series Service Regulators 0 Elster American Meter 00B Series Service Regulators General Information The 00B Series Service Regulators are available

More information

Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).

Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant). Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)

More information

INSTALLATION INSTRUCTIONS. CVS 67CFR Pressure Reducing Instrument Supply Regulator INTRODUCTION

INSTALLATION INSTRUCTIONS. CVS 67CFR Pressure Reducing Instrument Supply Regulator INTRODUCTION INSTALLATION INSTRUCTIONS CVS 67CFR Pressure Reducing Instrument Supply Regulator INTRODUCTION The CVS Controls 67CFR Filter regulator is a pressure reducing supply regulator typically used for pneumatic

More information

Mounting and Operating Instructions EB 8546 EN. Type 4708 Supply Pressure Regulators. Translation of original instructions. Type Type

Mounting and Operating Instructions EB 8546 EN. Type 4708 Supply Pressure Regulators. Translation of original instructions. Type Type Type 4708 Supply Pressure Regulators Translation of original instructions Type 4708-53 Type 4708-64 Type 4708-12 Mounting and Operating Instructions Edition March 2018 Note on these mounting and operating

More information

Needle valve. Contents. User s Manual. (1) Be sure to read the following warranty clauses of our product 1. (2) General operating instructions 2

Needle valve. Contents. User s Manual. (1) Be sure to read the following warranty clauses of our product 1. (2) General operating instructions 2 Serial No. H-V024-E-7 Needle valve User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for transportation,

More information

CAST IRON VALVES FLOAT VALVE

CAST IRON VALVES FLOAT VALVE CAST IRON VALVES FLOAT VALVE NETAFIM CAST IRON VALVES FLOAT VALVE INLINE 25-400MM ANGLE 50-100MM SPECIFICATIONS Manufactured to ISO 9001 Available Valve sizes INLINE Flanged 50mm to 600mm & Threaded 19mm

More information

DAV - P. Product Catalogue DAV - P. Air release & Vacuum Break Valves. (Plastic Air Valves) DAV - P. Edition 2012

DAV - P. Product Catalogue DAV - P. Air release & Vacuum Break Valves. (Plastic Air Valves) DAV - P. Edition 2012 Product Catalogue DAV - P DAV - P Air release & Vacuum Break Valves Edition 1 DAV - P (Plastic Air Valves) DAV Series Overview General The presence of trapped air in a pressurized pipeline can have serious

More information

2.0 INSTALLATION & SERVICE

2.0 INSTALLATION & SERVICE Installation, Operation, and Maintenance Instructions MODEL 5600 / 5600R January 2005 CONTENTS 1.0 GENERAL 1.1 5600 Model Number Information -----------------------------------------------------------------------

More information

HAYWARD FLOW CONTROL Series PBV Back Pressure Valve and Series RPV Pressure Relief Valve INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS

HAYWARD FLOW CONTROL Series PBV Back Pressure Valve and Series RPV Pressure Relief Valve INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS HAYWARD FLOW CONTROL Series PBV Back Pressure Valve and Series RPV Pressure Relief Valve INSTALLATION, OPERATION, AND MAINTENANCE INSTRUCTIONS Page 1 of 20 Page 2 of 20 TABLE OF CONTENTS Safety Warnings

More information

Full-Vacuum Chlorinator C 2212 MB / 1

Full-Vacuum Chlorinator C 2212 MB / 1 MB 2 04 12 / 1 Purpose of full-vacuum chlorinators Chlorine gas is important for the disinfection of potable and swimming pool water but also represents a source of danger as far as handling, transportation

More information

Pressure Relief Valve DHV 718

Pressure Relief Valve DHV 718 Advantages frictionless components low maintenance low pressure increase up to fully opened valve constant low vibration controlling hermetically sealed by diaphragm for oscillating pumps for viscous media

More information

Direct Operated Precision Regulator Modular Style. Standard Specifications

Direct Operated Precision Regulator Modular Style. Standard Specifications 1 Direct Operated Precision Regulator Modular Style Series P3 Courtesy of Steven Engineering, Inc.-23 Ryan Way, South San Francisco, CA 948-637-Main Office: (65) 588-92-Outside Local Area: (8) 258-92-www.stevenengineering.com

More information

Anderson Greenwood Series 93 Positive Pressure POSRV Installation and Maintenance Instructions

Anderson Greenwood Series 93 Positive Pressure POSRV Installation and Maintenance Instructions Before installation these instructions must be fully read and understood Installation and maintenance instructions for Series 93 Positive Pressure Pilot Operated Safety Relief Valves (POSRV). The intent

More information

Crosby style JCE Safety Valve Installation, Maintenance and Adjustment Instructions CROSBY

Crosby style JCE Safety Valve Installation, Maintenance and Adjustment Instructions CROSBY CROSBY Table of contents 1. Installation 1 1.1. Drainage 1 1.2. Discharge pipework 1 1.3. Preparation for installation 1 2. Pressure adjustment 1 3. Maintenance 1 4. Dismantling 1 4.1. All valve types

More information

MEGR-1912 Instruction Manual

MEGR-1912 Instruction Manual MEGR-1912 PRESSURE REGULATOR Instruction Manual- Look Inside For: Description Installation Start-Up Maintenance Parts Ordering Parts List Marshall Excelsior Company Marshall, MI 49068 269-789-6700 FAX

More information

Eaton Filtration, LLC

Eaton Filtration, LLC Eaton Filtration, LLC 900 Fairmount Avenue, Elizabeth, NJ 07207 Phone: 908-787-1000 Fax: 908-351-7893 E-Mail: filtration@eaton.com Web: www.filtration.eaton.com Installation, Operation & Service Manual

More information

WW-720. Pressure Reducing Control Valve

WW-720. Pressure Reducing Control Valve WW-720 Pressure Reducing Control Valve (Size Ranges: 2-4 and 6-14 ) Installation Operation & Maintenance Page 1 of 6 1. DESCRIPTION The Model 720 Pressure Reducing is an automatic control valve (powered

More information

Installation and operation Manual. Bermad Surge Anticipation Valve. Model No 435

Installation and operation Manual. Bermad Surge Anticipation Valve. Model No 435 Instruction manual Bermad surge anticipation manual Model No 435 Installation and operation Manual Bermad Surge Anticipation Valve Model No 435 Bermad Water Technologies Rev 0 5/05/2015 7 Inglewood Drive,

More information

Pressure Reducing Valve DMV 755 set range: 1,0-9,0 bar

Pressure Reducing Valve DMV 755 set range: 1,0-9,0 bar Pressure Reducing Valve DMV 755 set range:,0-9,0 bar Advantage pressure setting possible at any time, also during operation high reproducibility of the set pressure high level of operating safety and long

More information

WW-720. Pressure Reducing Control Valve

WW-720. Pressure Reducing Control Valve WW-720 Pressure Reducing Control Valve (Size Ranges: 2-4 and 6-14 ) Installation Operation & Maintenance Page 1 of 6 1. DESCRIPTION The Model 720 Pressure Reducing is an automatic control valve (powered

More information

HM and HM34 Inverted Bucket Steam Traps Installation and Maintenance Instructions

HM and HM34 Inverted Bucket Steam Traps Installation and Maintenance Instructions 0670350/4 IM-S03-11 ST Issue 4 HM and HM34 Inverted Bucket Steam Traps Installation and Maintenance Instructions 1. Safety information 2. General product information HM Series 3. Installation 4. Commissioning

More information

Mounting and Operating Instructions EB EN. Type Supply Pressure Regulator. with increased air capacity

Mounting and Operating Instructions EB EN. Type Supply Pressure Regulator. with increased air capacity Type 4708-45 Supply Pressure Regulator with increased air capacity Translation of original instructions Mounting and Operating Instructions EB 8546-1 EN Edition March 2016 Note on these mounting and operating

More information

BERMAD Waterworks. Level Control Valve with Altitude Pilot. 700 Series. Model X. Features and Benefits. Major Additional Features

BERMAD Waterworks. Level Control Valve with Altitude Pilot. 700 Series. Model X. Features and Benefits. Major Additional Features Level Control Valve with Altitude Pilot High level reservoirs & water towers Energy cost critical systems Systems with poor water quality Inherent refreshing Level sustaining at reservoir outlet The Level

More information

1800C and 1800C-HC Series Service Regulators

1800C and 1800C-HC Series Service Regulators 1800C and 1800C-HC Series Service Regulators Installation Instructions www.elster-americanmeter.com General Information: The 1800C and 1800C-HC Regulators are available as Full Capacity Internal Relief

More information

756 Safety Relief Valves

756 Safety Relief Valves 756 S a fe t y R e l i e f Va l ve s INTRODUCTION 756 Safety Relief Valves The effects of exceeding safe pressure levels in an unprotected pressure vessel or system, can have catastrophic effects on both

More information

End Connection. Thread x Thread N/A N/A N/A N/A Flange x Flange N/A

End Connection. Thread x Thread N/A N/A N/A N/A Flange x Flange N/A Worldwide Contacts www.tyco-fire.com Model RV-1 Pressure Relief Valve, Pilot-Operated, Globe and Angle Body Styles General Description Valves, through inch (DN50 through DN00), are factory assembled and

More information

TECHNICAL DATA 3 MODEL G-3000 DRY VALVE RISER ASSEMBLY

TECHNICAL DATA 3 MODEL G-3000 DRY VALVE RISER ASSEMBLY Page 1 of 13 1. DESCRIPTION The Viking 3 Model G-3000 Dry Valve Riser Assembly is equipped with a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry

More information

Reduce pressure zone device suitable for high and medium hazard rated applications Flanged end connections

Reduce pressure zone device suitable for high and medium hazard rated applications Flanged end connections VALVCHEQ Backflow Preventers Reduce pressure zone device suitable for high and medium hazard rated applications Flanged end connections Features General application The RP03 provides protection from both

More information

Mounting and Operating Instructions EB 2172 EN. Series 43 Temperature Regulators. Type 43-5 and Type Type Type 43-6

Mounting and Operating Instructions EB 2172 EN. Series 43 Temperature Regulators. Type 43-5 and Type Type Type 43-6 Series 43 Temperature Regulators Type 43-5 and Type 43-7 Type 43-6 Type 43-6 Type 43-7 with flanged valve body, DN 32 to 50 Type 43-5 Type 43-7 with welding ends Mounting and Operating Instructions EB

More information

Pressure Relief Valve DHV 718

Pressure Relief Valve DHV 718 Pressure Relief Valve DHV 718 Nominal size DN 8 50 Nominal size 3/8 2 Nominal pressure PN 10 bar Features pressure setting range 0.5 to 10 bar diaphragm controlled pressure relief valve simple design,

More information

RS(H)10,15 USER MANUAL. Read the complete manual before installing and using the regulator.

RS(H)10,15 USER MANUAL. Read the complete manual before installing and using the regulator. RS(H)10,15 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to

More information

Pressure Reducing Valve DMV 750

Pressure Reducing Valve DMV 750 ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 D-32602 Vlotho Fon +49 (0) 57 33-7 99-0 Fax +49 (0) 57 33-7 99-2 00 www.asv-stuebbe.de contact@asv-stuebbe.de Pressure Reducing Valve DMV 750 Advantages reduction

More information

TECHNICAL DATA Q = C. v P S. 2 Model G-2000 Dry valve. Page 1 of 13

TECHNICAL DATA Q = C. v P S. 2 Model G-2000 Dry valve. Page 1 of 13 Page 1 of 13 1. Description The Viking 2 Model G-2000 Dry Valve Riser Assembly consists of a small profile, light weight, pilot operated valve that is used to separate the water supply from the dry sprinkler

More information

Mounting and Operating Instructions EB 3009 EN. Self-operated Regulators. Type RS Check Valve (backflow protection)

Mounting and Operating Instructions EB 3009 EN. Self-operated Regulators. Type RS Check Valve (backflow protection) Self-operated Regulators Type 42-10 RS Check Valve (backflow protection) Type 42-10 RS Check Valve (backflow protection) Mounting and Operating Instructions EB 3009 EN Edition December 2015 Definition

More information

AIR AND VACUUM VALVES

AIR AND VACUUM VALVES MINING DIVISION AIR AND VACUUM VALVES FOR HIGH FLOW K-6NS SERIES DESCRIPTION The K-6NS Series Air and Vacuum Valve discharges air during the filling or charging of the system and admits air into the system

More information

Ball Float Steam Trap UNA 45 MAX, UNA 46 MAX, UNA 46A MAX PN 40/Class 300 DN 40, 50, 65

Ball Float Steam Trap UNA 45 MAX, UNA 46 MAX, UNA 46A MAX PN 40/Class 300 DN 40, 50, 65 Data Sheet 819346-02 Issue Date: 05/17 Ball Float Steam Trap UNA 45 MAX, UNA 46 MAX, UNA 46A MAX PN 40/Class 300, 50, 65 UNA 45hl MAX, UNA 46hl MAX, UNA 46Ahl MAX UNA 45v MAX with cover for mounting electrode

More information