PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO HIGH LEVEL LIGHT UNITS

Size: px
Start display at page:

Download "PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO HIGH LEVEL LIGHT UNITS"

Transcription

1 PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO HIGH LEVEL LIGHT UNITS Project: (insert Client) Replacement/ Repair of high level light units/ high level routine re-lamping Contractor: Planned Lighting Maintenance Ltd Accompanying Documentation to this Method Statement: 1. Planned Lighting Maintenance Ltd Health & Safety Policy Document Part I 2. Planned Lighting Maintenance Ltd Health & Safety Policy Document Part II 3. Planned Lighting Maintenance Ltd Health & Safety Policy Document Part III 4. Site Induction Talk Prompt Sheet Supervisor specific briefing 5. Static and Mobile Tower Scaffold Risk Assessment Checklist 6. Lamp Breakages PLM Form 1001 General Information: All work to be carried out in accordance with the contract documentation and good working practice as defined by the Part III Health & Safety Policy Document and specific Risk Assessment attached. Reference numbers throughout this document relate to in the main the Company Health & Safety Policy Document Part III (Safe Working Practices) as attached. Brief Description of Scope of Work: i) The PLM team will book in on site obtain the site specific safety information including any restrictions or special instructions ii) iii) iv) An initial brief site/works inspection will be conducted by the PLM supervisor to survey the scope of works and decide if any high level work requires powered access equipment or a mobile/fixed scaffold tower. Once the scope of work is surveyed and understood the supervisor will agree any required electrical isolation, identify the electrical isolation point and the strategy for maintaining secure work areas with the store management The PLM supervisor will carry out a site induction for the PLM engineering team in line with the site induction prompt card and the agreed electrical isolation v) If power access equipment is to be used it will be inspected and documentation checked for safe operation vi) If a static or mobile scaffold tower is to be used it will be checked for correct parts, fully erected, inspected and signed off, using the attached form, as safe to use 1 of Rev 6.0

2 vii) viii) When the agreed electrical isolation and area barriers are in place the high level work will be carried out by the qualified engineers (IPAF or PASMA) and will always include a banksman at ground level When the works are complete and the lighting is checked for correct operation the works area will be made good and the work area and electrical isolation control handed back to the store management. Detailed Sequence of Work: While this list is the intended sequence of work some tasks will take place concurrently and/or others may be brought forward or delayed depending on unforeseen problems that may arise. However, where these may affect safety revised risk assessments will be carried out to reduce risk so far as reasonably practicable. During all visits to site to carry out work the induction, equipment inspection and site inspection process will be carried out. 1. On arrival at site the PLM team will book in and obtain the required specific site safety information which will be included in the PLM supervisor s site induction. 2. The team in conjunction with the store s representative will walk the work area and identify and agree the scope of work to be completed. This will include briefing and agreeing with the store management the exclusion barrier strategy, identification of electrical isolation points and agreement with electrical isolation programme for the works period including how these will be locked out/ controlled at isolation point. 3. Prior to any work being carried out the PLM supervisor will complete a site specific induction for the PLM engineering team in line with the site induction prompt sheet. 4. Materials, tools and equipment will be delivered to the site work area using the correct manual handling techniques as laid down in SWP No Manual Handling to working areas. All lamps and replacement fittings will be kept in a suitable protective container and/or areas to avoid potential damage, breakages or being an obstruction to others. 5. The powered access equipment will be checked for safe operation including the emergency hydraulic release mechanism. All personal protective safety equipment will be checked including the fall restraint equipment lines and harness. Only qualified IPAF trained engineers will use the equipment. Note: The length of the fall arrest harness lines must be adjusted to ensure there is no possibility of moving out of the work basket. In the extremely unlikely event of suspension in a harness the banksman will immediately recover the operative to ground level by use of the automatic hydraulic release. 6. The work area route will be inspected on foot prior to the access equipment being manoeuvred into its start position. At all times a trained banksman will be used and suitable barrier will be put in place as required to maintain exclusion zones. The movement of these will be co-ordinated by the banksman who will additionally control customer movement away from any hazardous area. The powered access equipment will be used in line with the specific safety instruction and SWP No. 32 Powered Access Equipment and SWP No. 29 Working at Height. The same procedures for exclusion zones will be carried out for mobile/static scaffold towers which will be used in line with SWP No.31 Static and Mobile Scaffold Towers. 7. Prior to work taking place the electrical supply isolation points will be identified in preparation for the works to be carried out. 8. During the works and as required the electrical circuit will be confirmed as isolated by the engineering supervisor using suitable test equipment. 9. In sequence as decided by the PLM supervisor the light unit cover will be unfastened and placed in a safe position and the old units/ lamps removed. 2 of Rev 6.0

3 10. The new fitting/ lamps will be installed and connected. At the conclusion of the installation the electrical power will be switched back on. 11. The light unit will be switched on and checked for correct operation. 12. When moving between lamp fittings in high level platforms the area of movement will be set up as an exclusion zone to protect client staff and customers. The banksman must always remain in a safe position and never stand directly below the work platform. 13. Any movement in high level platforms will be supervised by a trained banksman at ground level. 14. When moving in high level access equipment the IPAF qualified operator will ensure they move the platform around/ under any fixed obstruction and do not try to move the obstruction away from the platform. 15. At the end of the works all equipment/ lamps, etc. will be removed for onward disposal and the area made good. 16. Where fixed or mobile scaffolding is identified as the best access equipment this will only be erected and dismantled by a PASMA trained engineer with an in date PASMA certificate attached to this method statement. When erected this will be inspected and signed off as safe to use by the PASMA qualified engineer using the static and mobile scaffold tower risk assessment checklist. Any mobile tower in excess of 4m will be reduced to 4m or less before it is moved. SITE SPECIFIC SAFETY 17. Engineers will park in the designated areas and report to the site/ signing in point before starting works. 18. High level works will be conducted mostly during normal operating hours and suitable exclusion zones set around the working area. Where the risk assessment walk round inspection indicates the risks are high the supervisor may advise the store management that the works may need to be carried out when the store is closed. If in doubt this will be referred to the engineering teams direct line manager. 19. Areas in close proximity to the works that could be potentially contaminated, i.e. customers stock/ sale items will be fitted with a suitable protective cover. 20. All electrical works will where appropriate be carried out under controlled electrical isolation by trained competent engineers. 21. Suitable and sufficient personal protective equipment (PPE) will be worn by operatives to include safety footwear, cotton gloves, hi-visibility waistcoat and fall restraint harness/equipment. If any eye infection risk exists, eye protection should be worn. 22. The Planned Lighting Maintenance Ltd supervisor will carry out a simple toolbox talk at the beginning of each shift where the work period exceeds one day to include: a reminder of site safety rules and emergency procedures. 23. All waste, lamps, fittings, etc will be returned to the vehicle for removal from site each day and appropriate Hazardous Waste streaming. 24. Any breakages to lamps during the works will be reported and recorded on PLM Form Isolation of electrical circuits will be carried out under the Clients or Company Permit to Work System using PTW/F3. 3 of Rev 6.0

4 Welfare 26. All welfare, toilet, first aid facilities and emergency evacuation procedures will be established at the initial survey stage and details passed on to the team during the induction. 27. Engineers must ensure they maintain good hygiene standards by washing before eating, drinking, etc. 28. No drink or food will be consumed outside of the designated areas and/or where they might be crosscontaminated. 29. No smoking is permitted on any site at any time. Security 30. Equipment, tools, etc will be secured in the vehicle when not in use and removed from site daily. The elevated work platform will be parked in the agreed designated area. Emergency Evacuation 31. The emergency evacuation procedures for the area are to be detailed during the site induction and employees reminded by the Team Supervisor on the daily toolbox talks. Miscellaneous 32. Prior to any works a copy of the building asbestos register should be obtained to confirm the presence or otherwise of asbestos containing materials. Where these have been identified and affect the working areas these will either be removed or suitable control measures implemented. Throughout the works if any hazardous materials are discovered work will cease and be reported immediately. An investigation will take place and risk assessments carried out by the Planned Lighting Maintenance Ltd Safety Officer. (See SWP No.20 Asbestos Awareness) Storage 33. No items will be stored on site where they can become a trip hazard or nuisance to others. No potentially combustible packaging materials or materials which could cause an obstruction will be left on site overnight other than in authorised areas. Originally prepared by: GMD Associates June 2017 UNDER NO CIRCUMSTANCES WILL OPERATION CONSIDERATIONS TAKE PRIORITY OVER SAFETY. UNDER NO CIRCUMSTANCES WILL HAZARDOUS MACHINERY, EQUIPMENT OR WORK AREAS BE LEFT UNATTENDED. 4 of Rev 6.0

5 ENVIRONMENTAL, HEALTH & SAFETY PROCEDURE 5.0 RISK ASSESSMENT CHECK LIST STATIC AND MOBILE SCAFFOLD TOWERS 5.1 The following will be completed by the supervisor prior to work being carried out on static and mobile scaffold towers and the signed certificates will be held with the tower at all times: Description of task 1. Are all parts matching and in good condition 2. Is the load capability sufficient for the type of work to be undertaken 3. Are you competent to erect this type of tower (PASMA) 4. Is the tower on a firm and level base which will hold the weight 5. Is it braced correctly 6. Is a proper access ladder in place 7. Are there any dangerous obstructions above or around the tower 8. Are all wheels where fitted locked off minimum 2x wheels 9. Are double guard rails and toe boards in place maximum gap 430mm 10. Are weather conditions suitable to continue work using the tower 11. The tower will not be moved with person or equipment on board and must be lower than 4m when moved 12. There are no obstructions, holes, etc where the tower is to be moved 13. The correct level of PPE is worn when working on or erecting the tower 14. If appropriate the tower is secured to some other fixed structure with sufficient proven strength 15. A suitable line or basket is in place for 5 of 11 YES NO Where the answer is NO to any of the questions detailed below, suitable remedial action to control the risk must be taken

6 ENVIRONMENTAL, HEALTH & SAFETY PROCEDURE raising/lowering equipment STATIC AND MOBILE SCAFFOLD TOWERS 16. Are suitable signs in place to warn others of the potential hazards Print Name Signature Date 6 of 11

7 RISK ASSESSMENT Site: (insert site) Assessor Graham Dann Date June 2017 Serial Hazard With No Control Measures Hazard With Control Measures Working in close proximity to site employees Where practicable carry out works out of normal or members of public operating hours Keep site employees and/or members of the public away from working areas by using banksmen and barriered exclusion zones Falls from height when using access equipment Use correct safe working procedures and fall Policy Nos: restraint harness equipment with short tethers Train engineers to competent IPAF Qualification Policy Reference Number Comments 29 - Working at Height and 32 - Powered Access Equipment 03 Injury while manual handling materials Train engineers Policy Nos: 15 Manual Use risk assessment procedure Handling Wear appropriate PPE gloves/ safety boots etc. 04 Injury from incorrect use of handtools and Use correct safe working procedures Policy Nos: 14 Handtools Power tools Wear appropriate PPE and 35 Portable Power Tools Select tools of high quality and power tools without residual risks (noise, vibration) use battery powered DC equipment 7 of 11

8 RISK ASSESSMENT Serial Hazard With No Control Measures Hazard With Control Measures Policy Reference Number Comments Working with electrical equipment Engineers to isolate electrical supply and confirm Policy No: 45 and PTW/F3 using appropriate test equipment Carry out work out of hours where practicable Permit to Work system to be used when required Handling of hot lamps Switch off where practicable and allow lamp to cool before handling Engineers to wear suitable gloves Commissioning of Equipment 07 Handling of broken lamps Store lamps in suitable container Engineers to wear suitable gloves Broken lamps to be removed to sharps bin or similar for correct disposal 08 Danger from falling objects to those below Set up exclusion zone and control below work Including handtools and equipment area 09 Exposure to asbestos containing materials Consult building asbestos register prior to works Policy No. 20 Asbestos and implement suitable controls Awareness Use safe working procedure 8 of 11

9 RISK ASSESSMENT Serial 10 Hazard With No Control Measures Hazard With Control Measures Incorrect working at high levels in access All users of access equipment to be PASMA Policy Nos: Policy Reference Number Comments equipment (scaffold tower) and/ or IPAF (powered access 29 Working at Height equipment) trained All movement in high level equipment to be supervised at ground level by a competent.banksman. All area of movement to be set up as total exclusion zones..platform to be moved around obstruction and.obstructions not to be moved away from platform Works to external areas to be conducted at suitable times to allow unrestricted access Towers only to be moved with sufficient clear areas to ensure a falling tower will not hit other persons. 31 Static and Mobile Scaffold Towers and 32 Powered Access Equipment 9 of 11

10 Where risks are identified their likelihood of occurrence will be classed as 1 to 5 as follows: 1. REMOTE Very Unlikely to Occur 2. POSSIBLE Unlikely to Occur 3. PROBABLE Probably Will Occur 4. FREQUENT Very Likely to Occur 5. CERTAIN Extremely Likely to Occur Where risks are identified they will further be assessed for potential severity as 2 to 10 as follows: 2. NEGLIGIBLE Negligible Injury or Consequence 4. MINOR Minor Injury or Consequence 6. SIGNIFICANT Significant Injury or Consequence 8. MAJOR Major Injury or Consequence 10. CRITICAL Critical Injury or Consequence These will then be transposed to the Risk Assessment Form where each figure is multiplied by the other to assess risk before and after control measures are employed 10 of 11

PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO LOW LEVEL LIGHT UNITS

PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO LOW LEVEL LIGHT UNITS PLANNED LIGHTING MAINTENANCE LTD METHOD STATEMENT & RISK ASSESSMENT REPLACEMENT OF LAMPS OR REPAIRS TO LOW LEVEL LIGHT UNITS Project: Insert Client Repair/ Replacement of low level light units/ low level

More information

Pre-control risk estimate. Likelihood Risk

Pre-control risk estimate. Likelihood Risk Activity Consequence s mitigation measures Site Access & Egress Slips, trips & falls al injury by falling. Sprains & broken bones. Site operatives 3 4 12 Ensure access to site is kept clear of plant &

More information

Safe Work Method Statement

Safe Work Method Statement TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Working at eight SWMS No. 16 Authorized and email Signed by the (Managing

More information

Instructions for the Use of the Excel Spreadsheet. There are Three tabs at the bottom of this worksheet. Instructions tab is the one you are reading

Instructions for the Use of the Excel Spreadsheet. There are Three tabs at the bottom of this worksheet. Instructions tab is the one you are reading Instructions for the Use of the Excel Spreadsheet There are Three tabs at the bottom of this worksheet Instructions tab is the one you are reading H&S Plan Tab The Plan Tab is the front cover pages of

More information

1. Objective of the initiative To ensure that all employees and subcontractors are aware of the risks associated with working at height.

1. Objective of the initiative To ensure that all employees and subcontractors are aware of the risks associated with working at height. Safety Initiative 02 Working at Height May 2011 CONTENTS 1. Objective of the initiative 2. Overview. 3. Implementation 4. Duties 5. Hierarchy of Controls 6. Workplace Inspections 7. Fragile Surfaces 8.

More information

2.0 Management Systems and Documentation

2.0 Management Systems and Documentation SHE Rules BOW142.3 1.0 Introduction This document details the safety, health and environment rules that apply to anyone accessing Arqiva sites and describes the standards of performance expected. This

More information

Safety Risk Assessment Working at Height: Mobile Tower Scaffold

Safety Risk Assessment Working at Height: Mobile Tower Scaffold Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees Mark Bloxidge H&S Manager 0208 821 5197 Working at height from Mobile Tower B Contractors/Sub contractors

More information

Company Health and Safety Policy

Company Health and Safety Policy Company Health and Safety Policy LDM Installers Ltd. Document reference: H&SP0B5-00 Document by: Radu N. Lupsa Date: 25.08.2010 Review date: 25.02.2011 36 CASTLEVIEW GARDENS, LONDON, IG1 3QB. TEL/FAX:

More information

B S Glass Ltd Safety procedures- outsourced Workplaces

B S Glass Ltd Safety procedures- outsourced Workplaces B S Glass Ltd Jan 17 B S Glass Ltd Safety procedures- outsourced Workplaces Index - - - - - - - - Page No On Site safety - - - - - - - - - - - - - - - - - - - Content 3. 1.00 Health and Safety Mission

More information

FIRE HYDRANT TESTING METHOD STATEMENT.

FIRE HYDRANT TESTING METHOD STATEMENT. SUBJECT: TASK: FIRE HYDRANT INSPECTION & TESTING. 1. Location....1 2. The Scope of Works.... 1 3. Description of Task.... 1 4. Access & Egress to & from Work Area.... 2 5. Safety Hazard Identification....

More information

Safe Work Method Statement

Safe Work Method Statement Title Skid Steer Operation (Bobcat) SWMS No. 14 Authorized and email Signed by the (Managing Director / CEO / Partner / Proprietor) on Date 01/08 /2016 Safe Work Procedure for the Work:- Yes No Employees

More information

Section J. How to develop safety elements for project safety management system. How to develop safety elements for project SMS

Section J. How to develop safety elements for project safety management system. How to develop safety elements for project SMS Section J How to develop safety elements for project safety management system 1. Once the project management has developed or adopted a safety policy, it needs to develop safety elements to meet the objectives

More information

Contractor / Exhibitor Handbook

Contractor / Exhibitor Handbook Contractor / Exhibitor Handbook Health and Safety This booklet outlines the basic rules that must be followed by contractors and other visitors working on Live Promotions Events sites. The contractors

More information

MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY FALL HAZARD CONTROL REQUIREMENTS SERIES & NO. SMI - 157

MANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY FALL HAZARD CONTROL REQUIREMENTS SERIES & NO. SMI - 157 1 of 6 1.0 PURPOSE To establish minimum requirements and guidelines for controlling hazardous exposure of personnel to falls from working elevations in conformance with Federal and State OSHA rules and

More information

CONSTRUCTION HEALTH AND SAFETY MANAGEMENT SYSTEM BASELINE HIRA

CONSTRUCTION HEALTH AND SAFETY MANAGEMENT SYSTEM BASELINE HIRA RECOMMENDED ADDITIONAL CONTROLS TASK / ACTIVITY/ EQUIPMENT/ FACILITY HAZARDS UNWANTED EVENT MINIMUM CONTROLS REQUIRED RISK NO. LIKELI-HOOD CONSE-QUENCE RISK VALUE Project Risk Assessment Page 1 of 16 All

More information

S31 Opening Statement Working at Height

S31 Opening Statement Working at Height S31 Opening Statement Working at Height Falls from height are by far the most common cause of workplace deaths and one of the main causes of major injury in the workplace. Latest figures reveal that 46

More information

Contractor handbook. Purpose

Contractor handbook. Purpose Page no: 1 / 6 Contractor handbook Purpose Mitie aims to ensure that the highest levels of performance are achieved by all persons working for us or on our behalf. We require the same level of performance

More information

FALL PROTECTION WORK PLAN (Alstom Power Installation Canada)

FALL PROTECTION WORK PLAN (Alstom Power Installation Canada) FALL PROTECTION WORK PLAN (Alstom Power Installation Canada) Location: Unit: Foreman: Task: Supervisors Ensure: Workers must review and sign this fall protection work plan prior to starting work in an

More information

Working at Height - MEWPS & Ladders. Your company details Address Tel: Fax: Mobile:

Working at Height - MEWPS & Ladders. Your company details Address Tel: Fax: Mobile: Project/Contract Contractor Site Address Project Start Date Expected Duration Projected Completion Date Your company details Address Tel: Fax: Mobile: Document Author Authorised by Name Title Signature

More information

Safety Risk Assessment Roofing Works / Surveying / Inspections

Safety Risk Assessment Roofing Works / Surveying / Inspections One Direct aintenance td Persons at (Groups) Assessor Appointment Tel. No. Description of Task or Activity A One Direct employees ark Bloxidge H&S anager 0208 821 5197 One Direct Operatives accessing roof

More information

Working at Height. Policy and Procedures. Author: Beth Webster Assistant Safety Advisor. On behalf of School Safety Committee.

Working at Height. Policy and Procedures. Author: Beth Webster Assistant Safety Advisor. On behalf of School Safety Committee. Working at Height Policy and Procedures Author: Beth Webster Assistant Safety Advisor Authorised by: Issued by: John Stephenson Safety Office On behalf of School Safety Committee Review Date: NO LATER

More information

LADDERS FIXED AND PORTABLE

LADDERS FIXED AND PORTABLE CONTRACTOR WHS HAZARD STANDARD LADDERS FIXED AND PORTABLE EXTERNAL USE ONLY Principles in the Optus Contractor WHS management process CONTRACTOR MANAGEMENT STAGES PRINCIPLES THIS STANDARD REQUISITION Requisition

More information

Method Statement Author

Method Statement Author Plan Bee Limited 3.3 Etna Industrial estate Clamp Road Motherwell Scotland ML2 7XQ Tel: 01698580572 Method Statement Method Statement Details Method Statement Number 7 Method Statement Date Monday 3rd

More information

LEVEL 2 CERTIFICATE OF COMPETENCE IN THE SAFE USE AND OPERATION OF MOBILE ELEVATED WORK PLATFORMS

LEVEL 2 CERTIFICATE OF COMPETENCE IN THE SAFE USE AND OPERATION OF MOBILE ELEVATED WORK PLATFORMS NPTC Registered Charity No. 1096429 NATIONAL AGRICULTURAL CENTRE STONELEIGH PARK, WARWICKSHIRE CV8 2LG Tel: 024 7669 6553 Fax: 024 7669 6128 Email: information@nptc.org.uk LEVEL 2 CERTIFICATE OF COMPETENCE

More information

Work At Height Health & Safety Management Standard Issue 3 (April 2011)

Work At Height Health & Safety Management Standard Issue 3 (April 2011) Work At Height Health & Safety Management Standard Issue 3 (April 2011) Introduction This document contains corporate standards and guidance on the management of risks arising from work at height. It is

More information

Waste Industry Safety & Health

Waste Industry Safety & Health Waste Industry Safety & Health A practical pocket guide for the Waste industry Supported by: Delivering the Solution Together Introduction The Waste Industry Safety and Health (WISH) forum is supporting

More information

Safe Work Method Statement

Safe Work Method Statement TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Dogging of Crane General Loading and Unloading SWMS No. 20 Authorized

More information

HEALTH & SAFETY ARRANGEMENTS FOR MANAGEMENT OF WORK AT HEIGHT

HEALTH & SAFETY ARRANGEMENTS FOR MANAGEMENT OF WORK AT HEIGHT HEALTH & SAFETY ARRANGEMENTS FOR MANAGEMENT OF WORK AT HEIGHT INTRODUCTION Cwmni CYNNAL recognises that accidents can arise from working at height. Falls from height can be a cause of injury and absence

More information

Safe Work Method Statement (SWMS)

Safe Work Method Statement (SWMS) Safe Work Method Statement (SWMS) Organisation Details : Organisation Name Northern Plumbing Contact ABN 17 15 41 4 Position Director Address 47 Thomas Street Edgeworth 85 Phone Number 0411 10 4 Project

More information

Safe Work Procedure for installation of external cladding

Safe Work Procedure for installation of external cladding Safe Work Procedure for installation of external cladding This procedure has been formulated to cover safe systems of work for the installation of external cladding. This instruction will be used to reduce

More information

Contractor Hazard Identification and Control Guide

Contractor Hazard Identification and Control Guide Exposure to Asbestos Containing Materials (ACM) Accidental disturbance or removal of ACM. Asbestos Containing Materials are to be removed outside school hours. No DET employees, students or visitors are

More information

THE CONTROLLED COPY OF THIS DOCUMENT IS ON THE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR THE DATE AT THE BOTTOM OF THE PAGE.

THE CONTROLLED COPY OF THIS DOCUMENT IS ON THE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR THE DATE AT THE BOTTOM OF THE PAGE. TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Using Angle Grinders SWMS No. 8 Authorized and email Signed by the

More information

The Site-Specific Safety Plan V prepared for

The Site-Specific Safety Plan V prepared for The Site-Specific Safety Plan V12017 prepared for Site-Specific Safety Plan All the documents you need can be accessed through the menu below. Click on the icon to go to the section that applies to you.

More information

The Sample Company Pty Ltd

The Sample Company Pty Ltd Job Safety and Environmental Analysis (JSEA) / Safe Work Method Statement (SWMS) Part 1: Project and Task Identification Process Initiators of SWMSs are responsible for consulting the Project Supervisor,

More information

Permit-To-Work Guidance and Templates

Permit-To-Work Guidance and Templates Managing Contractors Policy - Appendix E Permit-To-Work Guidance and Templates This document has been constructed to provide guidance in how to use a permit to work correctly. The first part explains the

More information

CONTRACTOR SAFETY INDUCTION HANDBOOK

CONTRACTOR SAFETY INDUCTION HANDBOOK CONTRACTOR SAFETY INDUCTION HANDBOOK As a valued contractor for Total Group we would ask that you read and carefully consider the details included in this document. Total Group carry out work for a number

More information

IMMANUEL CHURCH, CHICHESTER HEALTH AND SAFETY POLICY

IMMANUEL CHURCH, CHICHESTER HEALTH AND SAFETY POLICY IMMANUEL CHURCH, CHICHESTER HEALTH AND SAFETY POLICY Approved by the Trustees: November 2016 Health and Safety Policy Introduction The main piece of health and safety legislation is the Health and Safety

More information

Work Activity (e.g. Road Work): Work Location:.

Work Activity (e.g. Road Work): Work Location:. Working with Cranes Work Activity (e.g. Road Work): Work Location:. GENERAL INFORMATION Hinchinbrook Shire Council Lannercost Street Ingham Qld, 4850 ABN 46 291 971 168 Ph: 47764610 All personnel conducting

More information

Join t Op e ra tion s CHESM Fie ld I n s p e ction Ch e cklis t

Join t Op e ra tion s CHESM Fie ld I n s p e ction Ch e cklis t JO CHESM Field Inspection Checklist Join t Op e ra tion s CHESM Fie ld I n s p e ction Ch e cklis t This checklist provides a format for the recording of observations at work sites visited during the inspection.

More information

SAFE WORK METHOD STATEMENT SWMS No Version

SAFE WORK METHOD STATEMENT SWMS No Version SAFE WORK METHOD STATEMENT SWMS No Version Company Name: Hunter Readymixed Concrete Pty Ltd 00 004 Location: Thornton Cessnock Tea Gardens Gateshead ABN: 6 076 08 695 SWMS Developed By: Duane Harrison

More information

Safe Work Method Statement

Safe Work Method Statement TE CONTROLLED COPY OF TIS DOCUMENT IS ON TE COMPUTER NETWORK PRINTED COPIES ARE ONLY CURRENT FOR TE DATE AT TE BOTTOM OF TE PAGE. Title Use of a Mobile Elevated Work Platform (MEWP) Boom SWMS No. 19 Authorized

More information

Site-Specific Safety Plan

Site-Specific Safety Plan Site-Specific Safety Plan All the documents you need can be accessed through the menu below. Click on the icon to go to the section that applies to you. Once in the section you can easily click the back

More information

How severely could the risk hurt someone? Low/Insignificant First aid

How severely could the risk hurt someone? Low/Insignificant First aid Safe Work Method Statement No: WMS-02 Task: Concreting, Formwork and Steel Fixing This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia)

More information

FALL PROTECTION / ELEVATED WORK

FALL PROTECTION / ELEVATED WORK SEPTEMBER CORE REFRESHER HSE TOOL BOX FALL PROTECTION / ELEVATED WORK FALL PROTECTION Falls from elevations are one of the most common causes of death in this industry. OSHA requires fall protection when

More information

Company Health & Safety Policy

Company Health & Safety Policy Westoaks Builders Ltd Reviewed 12th Jan 2015 HS27: Company Health & Safety Policy 1 Company Health & Safety Policy Statement of General Policy The Organisation accepts the obligations placed upon it by

More information

Refresher Licensed Asbestos Supervisor Training

Refresher Licensed Asbestos Supervisor Training TRAINING SYLLABUS LICENSED WORK WITH ASBESTOS Refresher Licensed Asbestos Supervisor Training This unit has nineteen learning outcomes. 1. Recognise the types, uses and risks of asbestos containing materials

More information

CLIENT: UNIVERSAL TOOL & PRODUCTION COMPANY Ltd. METHOD STATEMENT Commissioning and Final connections to IHT Skid

CLIENT: UNIVERSAL TOOL & PRODUCTION COMPANY Ltd. METHOD STATEMENT Commissioning and Final connections to IHT Skid CLIENT: UNIVERSAL TOOL & PRODUCTION COMPANY Ltd METHOD STATEMENT Commissioning and Final connections to IHT Skid UNITS 15/16 DAEDALUS HANGERS EAST GOSPORT Development: Title & Company Name Signature Date

More information

Prevention of Falls and Working at Heights

Prevention of Falls and Working at Heights Workplace Safety Schools Cleaning Prevention of Falls and Working at Heights It is the policy of the Company to avoid working at heights above 2 metres wherever practical. When avoidance is not an option,

More information

Conducting An Effective. Welcome!

Conducting An Effective. Welcome! Conducting An Effective An introduction to the Five Step Process of Job Hazard Analysis JHA-JSA-SWMS-AHA Introductions Welcome! What do you know about Job Hazard Analysis (JHA s)? Does OSHA require JHA

More information

You must NOT touch any equipment unless you are authorised to work on or with that equipment and you have followed correct safety procedures.

You must NOT touch any equipment unless you are authorised to work on or with that equipment and you have followed correct safety procedures. SYDNEY TOWN HALL 1 HIRER & CONTRACTOR SAFETY FACT SHEET Issue 2 September 2013 www.sydneytownhall.com.au City of Sydney - Venue Management will provide and maintain a safe working environment for the health,

More information

Work Health and Safety Risk Management Procedures

Work Health and Safety Risk Management Procedures Work Health and Safety Risk Management Procedures Table of Contents 1. Governing Policy 2. Purpose 3. Scope 4. Definitions 5. Responsibilities 6. Risk Management Process 6.1. Process summary 6.2. Hazard

More information

Safety Checklist for Events Held at Hillbrook

Safety Checklist for Events Held at Hillbrook Safety Checklist for Events Held at Hillbrook Hazards/ Issues or Tasks 1. EVENT ACCESS AND EGRESS Entry / Exit areas are kept clear and accessible. For an evening event, that you have appropriate Lighting.

More information

SUMBSE01 - SQA Code HC85 04 Apply health and safety and environmental legislation in the building services engineering sector

SUMBSE01 - SQA Code HC85 04 Apply health and safety and environmental legislation in the building services engineering sector Overview This standard is about establishing and maintaining working practices and procedures across a specified range of installation and/or maintenance activities that give consideration to health and

More information

Deans, Directors, Heads of Schools and Departments and Research Institute Directors and Managers

Deans, Directors, Heads of Schools and Departments and Research Institute Directors and Managers Working at Height 1. PURPOSE 1.1 To ensure that any work at height is carried out in accordance with the legal requirements and associated guidance. This includes the use of scaffolds, towers, ladders,

More information

SH&E Work Method Statement Concrete Cutting & Drilling Fast Cut Qld Pty Ltd, 91 Basalt, GEEBUNG PH M ABN

SH&E Work Method Statement Concrete Cutting & Drilling Fast Cut Qld Pty Ltd, 91 Basalt, GEEBUNG PH M ABN SH&E Work Method Statement Concrete Cutting & Drilling Fast Cut Qld Pty Ltd, 91 Basalt, GEEBUNG PH 07 3265 6537 M 0411 756 719 ABN 45 081 359 613 OHS-FRM-100 Rev 11 (07/18) Page 1 SH&EWMS No.: F-C-QLD-30

More information

Safety File. Contract Avonbourne School Prepared By Steve Steel Date 20 th July 2008

Safety File. Contract Avonbourne School Prepared By Steve Steel Date 20 th July 2008 S.P.S LOUVRE SYSTEMS LIMITED Directors S.C Steel & S.A Pearce Company Registration No. 5794591 VAT Registration No, 885 2670 86 CIS Scheme No, 9197816897101 Safety File Contract Avonbourne School Prepared

More information

SAFE WORK METHOD STATEMENT CARPENTER

SAFE WORK METHOD STATEMENT CARPENTER HOST EMPLOYER DECLARATION I declare the worker/s named on this work authority have been provided with a site specific safety induction that complies with the requirements of the Workplace Health & Safety

More information

Instructions: Use this format to prepare the security plans for ACP contracts. EVERY point has to be covered; if they do not apply, write N/A.

Instructions: Use this format to prepare the security plans for ACP contracts. EVERY point has to be covered; if they do not apply, write N/A. APPENDIX F - RISK CONTROL PLAN FORMAT FOR CONTRACTORS OF THE PANAMA CANAL Instructions: Use this format to prepare the security plans for ACP contracts. EVERY point has to be covered; if they do not apply,

More information

Telco Antennas SWMS Working At Height Above 2m

Telco Antennas SWMS Working At Height Above 2m Telco Antennas SWMS Working At Height Above 2m A SWMS shall be developed for a task where the risk has been assessed as Medium or Higher Division: Date: SWMS No: (e.g. Installation, Engineering Workshop)

More information

COMPANY HEALTH & SAFETY POLICY

COMPANY HEALTH & SAFETY POLICY COMPANY HEALTH & SAFETY POLICY 1 STATEMENT OF GENERAL POLICY The Organisation accepts the obligations placed upon it by the various Acts of Parliament covering health, safety and welfare including: Deposit

More information

SWMS No 007 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6

SWMS No 007 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6 Samark North Qld Pty Ltd SWMS Manual SWMS No 007 Samark North Qld Pty Ltd ABN : 99 082 958 487 Electrical Contractors License C37121 Page 2 of 6 Safe Work Method Statement Title: SWMS:007 WORKING ON ENERGISED

More information

2.0 Dates and Times Tests to be carried out starting Monday 28 Nov for completion Friday 2 Dec.

2.0 Dates and Times Tests to be carried out starting Monday 28 Nov for completion Friday 2 Dec. MS No: :. A 1.0 Scope of Work Preparation notes: delete column before issuing. 1.1 General Description of Works, Location & Boundaries Strength and tightness testing of Glycol System between plant room

More information

Procedure: Work health and safety hazard management

Procedure: Work health and safety hazard management Procedure: Work health and safety hazard management Purpose This procedure describes how the Australian National University (ANU) manages Work Health Safety hazards for the health, safety, rehabilitation

More information

OSHA s new walking working surfaces standards

OSHA s new walking working surfaces standards OSHA s new walking working surfaces standards changes and new requirements Inspection of walking working surfaces 1910.22(d) Regularly and as needed and correct, repair, or guard against hazardous conditions;

More information

Staff Contractors. Public. Staff Contractors

Staff Contractors. Public. Staff Contractors 1. Vehicle movements In conjunction with the vehicle driver, venue management and the client, our staff should ensure the safe parking of vehicles for loading and unloading purposes. Depending upon circumstances

More information

TRADE AREA: ELECTRICAL INDUSTRY

TRADE AREA: ELECTRICAL INDUSTRY TRADE AREA: ELECTRICAL INDUSTRY Some possible workplace hazards and possible ways for Host employers and Apprentices/Trainees in controlling these hazards. What are possible hazards? What could be possible

More information

Pocklington Town Council Risk Assessment Christmas Festival Wednesday Assessor: Gordon Scaife Date

Pocklington Town Council Risk Assessment Christmas Festival Wednesday Assessor: Gordon Scaife Date Activity: Christmas Festival Wednesday Assessor: Gordon Scaife Date 16/07/2018 5 December Completed: Persons At Risk: PTC Staff, Volunteers & Public Reference: 180716 Public Events Review Date: 16/07/2019

More information

RISK ASSESSMENT A UNIVERSITY GUIDE TO PRACTICAL RISK ASSESSMENT UNDER THE MANAGEMENT OF HEALTH AND SAFETY AT WORK REGULATIONS 1992

RISK ASSESSMENT A UNIVERSITY GUIDE TO PRACTICAL RISK ASSESSMENT UNDER THE MANAGEMENT OF HEALTH AND SAFETY AT WORK REGULATIONS 1992 RISK ASSESSMENT A UNIVERSITY GUIDE TO PRACTICAL RISK ASSESSMENT UNDER THE MANAGEMENT OF HEALTH AND SAFETY AT WORK REGULATIONS 1992 PERSONNEL DIVISION REVIEWED AUTUMN 1999 CONTENTS Page 1 INTRODUCTION 1

More information

List all key terms and acronyms used in the procedure, and their definitions.

List all key terms and acronyms used in the procedure, and their definitions. Purpose The purpose of this procedure is to provide guidelines for electrical safety in general within Seqwater in compliance with the Electrical Safety Act 2002, Industry Codes of Practice, Regulations,

More information

Specific Safety Legislation/Codes of Practice/Australian Standards applicable to this JSA (Tick those applicable).

Specific Safety Legislation/Codes of Practice/Australian Standards applicable to this JSA (Tick those applicable). OCCUPATIONAL HEALTH & SAFETY MANUAL Section OHS-005, Job Safety Analysis SCORESBY, VIC 3179 GEELONG, VIC 3218 MALAGA, WA 6090 DUDLEY PARK, SA 5008 MANSFIELD, QLD 4122 NORTH ROCKS, NSW, 2641 ACT 2609 LAVINGTON,

More information

Monitoring excavation in the highway

Monitoring excavation in the highway This unit covers the requirements that you must meet when monitoring excavation work in the highway. You must ensure that you act in accordance with all current specifications and procedures and that you

More information

Safe Work Method Statement LRB TREE SERVICES 6 Behland St, Kearneys Spring QLD, 4350 ABN

Safe Work Method Statement LRB TREE SERVICES 6 Behland St, Kearneys Spring QLD, 4350 ABN JOB NO: PROJECT: DATE: 1/1/2018 SWMS NO: SWMS 001.1 PREPARED BY: LUKE BLINCO REVISED BY: ACTIVITY: TREE REMOVAL & PRUNING SIGNED BY: REVISION DATE: MINIMUM PERSONAL PROTECTIVE EQUIPMENT (PPE) REQUIREMENTS

More information

Application of rope access methods in the construction, inspection, repair and maintenance of wind turbines

Application of rope access methods in the construction, inspection, repair and maintenance of wind turbines Application of rope access methods in the construction, inspection, repair and maintenance of wind turbines Introduction IRATA International s rope access system is a safe method of working at height,

More information

Fall Protection and Elevated Work

Fall Protection and Elevated Work Program No: SP-010 Page 1 1.0 PURPOSE AND INTRODUCTION Fall Protection and Elevated Work To establish fall protection safety procedures for Pitt County Schools employees engaged in any of the following

More information

Hazard Identification and Risk Assessment Form. Risk Assessment

Hazard Identification and Risk Assessment Form. Risk Assessment Identification and Assessment Form Assessment Tool & Machine Work General Various injuries (including potential fatalities) All staff complete safety induction programme at the start of the module. instructed

More information

Hazard Management Making your workplace safer

Hazard Management Making your workplace safer Hazard Management Making your workplace safer A Guide to Hazard Identification, Risk Assessment, Control and Reviewing 1 What is a hazard? A hazard is something which has the potential to harm the health,

More information

SAFE WORK METHOD STATEMENT

SAFE WORK METHOD STATEMENT SAFE WORK METHOD STATEMENT AUGER / POST HOLE DIGGER Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES

More information

Release: 1. UEPOPL002A Licence to operate a reciprocating steam engine

Release: 1. UEPOPL002A Licence to operate a reciprocating steam engine Release: 1 UEPOPL002A Licence to operate a reciprocating steam engine UEPOPL002A Licence to operate a reciprocating steam engine Modification History Not applicable. Unit Descriptor Unit Descriptor 1)

More information

SWMS documented by: Feb Bo Ceprnja Date Feb Feb Feb 2018

SWMS documented by: Feb Bo Ceprnja Date Feb Feb Feb 2018 Contractor Company Details: BUILDSAFE SAFE WORK METHOD STATEMENT 0002 (Void Platform Stairs) Part 1 (To be used in conjunction with SWMS 0001 General Site Activities & SWMS 0002 Void Platform) Additional

More information

Lifting Operation & Lifting Equipment Procedure

Lifting Operation & Lifting Equipment Procedure SRSS Lifting Equipment Procedure 1. DOCUMENT CONTROL Management System Element Title SRSS SMS PROCEDURE Lifting Operation & Lifting Equipment Procedure SMS_HS_PR_033_ Version # & V1 10/08/2016 Lifting

More information

Potential hazards People at risk and how? Actions already in place Further action required Action by

Potential hazards People at risk and how? Actions already in place Further action required Action by Risk Assessment Flat Roof Repair Prepared by Oracle Managed Services For: BAM FM On: 24/02/2017 Review date: N/A Potential hazards People at risk and how? Actions already in place Further action required

More information

Wheeler Cranes 6 McIntyre Rd Tomago NSW 2324

Wheeler Cranes 6 McIntyre Rd Tomago NSW 2324 Wheeler Cranes 6 McIntyre Rd Tomago NSW 2324 ABN: 34 088 229 190 This SWMS has been developed and authorised by: Name Albie Wheeler Position Managing Director Date 1/7/12 Signature Phone 0249649991 Mobile

More information

How to plan an event. Step 1: First things first. Step 2: How to make it all happen?

How to plan an event. Step 1: First things first. Step 2: How to make it all happen? As an event organiser, you have a legal responsibility to ensure the health, safety and welfare of all those involved in your event - all employees, volunteer helpers and contractors as well as members

More information

PLANT RISK ASSESSMENT REPORT

PLANT RISK ASSESSMENT REPORT PLANT RISK ASSESSMENT REPORT SECTION 1: PLANT IDENTIFICATION Report Number: 407/752 Assessment Date: 5 th May 2015 Company: Wacker Neuson Plant Type: Telescopic Light Balloon Make: Wacker Neuson Model:

More information

Health and Safety Inspection Procedure

Health and Safety Inspection Procedure Template v4 WILTSHIRE POLICE FORCE PROCEDURE Health and Safety Inspection Procedure Effective from: 25.03.2012 Last Review Date: 10.05.2015 Version: 2.0 Next Review Date: 10.05.2018 TABLE OF CONTENTS PROCEDURE

More information

UCAS shell scheme event organiser risk assessment

UCAS shell scheme event organiser risk assessment UCAS shell scheme event assessment Assessor: Emily Bibby Monitored by: David Hale Date assessed: 22/01/18 Event: Manchester HE Exhibition Signature: Title: Events Organiser Organisation: UCAS Venue: Manchester

More information

WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST

WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST Windmill Hazard Inspection Checklist WINDMILL (pre-start) HAZARD INSPECTION CHECKLIST Authorised by: LOCATION OF INSPECTION...... Inspected By (1)........... (2)..... PRINT PRINT Signature (1):. (2)....

More information

Example of an Occupational Health Risk Assessment

Example of an Occupational Health Risk Assessment SITE: ASSESSMENT DATE: EQUIPMENT/ AREA/TASK: Floor Manual ASSESSED BY: TASK/ EQUIPMENT floor manual sorting HAZARD RISK PERSONS RATING EXISITING CONTROL MEASURES AT RISK S L R FURTHER ACTION REQUIRED R

More information

Contractor/Visitor Safety Orientation UNBC

Contractor/Visitor Safety Orientation UNBC Contractor/Visitor Safety Orientation UNBC 3333 University Way, Prince George, BC V2N 4Z9 Revised: October 2015 For All Emergencies call Security 250-960-7058 ***DO NOT DIAL 911*** Important UNBC Telephone

More information

New Licensed Asbestos Operative Training

New Licensed Asbestos Operative Training TRAINING SYLLABUS LICENSED WORK WITH ASBESTOS New Licensed Asbestos Operative Training This unit has twenty-two learning outcomes. 1. Recognise the types, uses and risks of asbestos containing materials

More information

Health, Safety and Welfare Policy

Health, Safety and Welfare Policy Health, Safety and Welfare Policy This Policy is prepared in accordance with section 2(3) the Health and Safety at work etc. Act 1974, with the intention of promoting a safe working environment that will,

More information

C&P ENGINEERING SERVICES LTD

C&P ENGINEERING SERVICES LTD Hazard Identification, Risk Assessment & Safe Working Procedure for Re-Lamping and Cleaning Light Fittings at Dow Corning Ltd, Barry Assessed By: Print Name Signature Date Assessed Assessment Review Date

More information

EXHIBITION Guide. Roles and Responsibilities OS11. A handbook for exhibitors and contractors

EXHIBITION Guide. Roles and Responsibilities OS11. A handbook for exhibitors and contractors Appendix 1 Health & Safety Declaration, Roles and Responsibilities Each exhibitor and Informa appointed contractor must complete the Health and Safety Declaration form provided below to confirm they have

More information

Leicester City Council Health & Safety Risk Assessment Form Ref:

Leicester City Council Health & Safety Risk Assessment Form Ref: Division/Section: Bridges Team Work Activity: Structural Repairs Activity Location: 8 Minehead Street, Leicester Persons Affected: Manager: Date of Assessment: Property Occupiers and Site Operatives Abul

More information

J&S Cooper Utilities

J&S Cooper Utilities Working at Heights Inspection conducted for J&S Cooper Utilities Conducted on 17 Apr 2018 08:35 AM Location 11953 Tyler Rd, Red Bluff, CA 96080, USA Prepared by SafetyCulture Staff Completed on 17 Apr

More information

EMPLOYEE SAFETY ORIENTATION - PHYSICAL PLANT, RESIDENCE

EMPLOYEE SAFETY ORIENTATION - PHYSICAL PLANT, RESIDENCE Name Department Initial Orientation Date Supervisor Review Instructions: Check off each section once you have read and discussed it with your Supervisor. EMPLOYEE SAFETY ORIENTATION - PHYSICAL PLANT, RESIDENCE

More information

SWMS No 012 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6

SWMS No 012 Samark North Qld Pty Ltd ABN : Electrical Contractors License C37121 Page 2 of 6 Samark North Qld Pty Ltd SWMS SWMS No 0 Samark North Qld Pty Ltd ABN : 99 08 98 87 Electrical Contractors License C37 Page of 6 Safe Work Method Statement Title: SWMS:0 INSTALLING LIGHT POLES Work Method

More information

Contractor Code of Conduct

Contractor Code of Conduct Application This procedure and associated documents are based on Health, Safety and Environmental best practice. Additional guidelines may be required within countries where local and / or in-country regulations

More information

FLYING OBJECTS MANUAL HANDLING EXCESSIVE NOISE

FLYING OBJECTS MANUAL HANDLING EXCESSIVE NOISE JOB NO: PROJECT: DATE: SWMS NO: SWMS 002 PREPARED BY: Ian Hartley REVISED BY: Nick Bragg & Cameron McNeil ACTIVITY: STUMP REMOVAL SUPERVISED BY: REVISION DATE: April 2016 MINIMUM PERSONAL PROTECTIVE EQUIPMENT

More information

Hautbois Risk Assessment

Hautbois Risk Assessment Hautbois Risk Assessment Activity: Estate Assessor: Rachel Jarman Date: January 2012 Tech Advisor: Martin Review Date: January 2013 Page: 1 of 8 Description: The Hautbois Estate comprises 28 acres of parkland,

More information