Die Temperature Control Fitting Series

Transcription

1 FITTING ONTROLLER VALVE TUE MAKE-TO-ORDER PRODUTS Push-In Fitting Type Molding oupling Fitting 244 Push-In Fitting Type for. Thermal Oil, lean Water and Air for Fluid Medium. No Projection left on the die, after uncoupling Plug. Stop Valve uilt-in Type prevents ot Water Ejection when uncoupling Plug. Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling olor ap

2 Fitting Fitting FITTING Model Designation (Example) AK Type 2 Fitting Type 3 onnection size 6 Parts 5 Thread size 4 Tube dia. / Inner thread 1 Type AK:Without stop valve (Standard type) AS:With stop valve 2 Fitting Type(No code: Thread part (socket) only) :Straight L:Elbow 3 onnection size 08:08 series (Standard type only) 10:10 series 245 Standard Mini Stainless hemical PP EG Anti-spatter & rass 4 Tube dia. / Inner thread(no code: Thread part (socket) only) Tube dia. Tube O.D. mm Tube I.D. inch Inner thread ode ID06 ID09 01F 02F 03F Size ø6 ø8 ø10 ø12 1/4 3/8 Rc1/8 Rc1/4 Rc3/8 5 Thread size(no code: Fittng part (plug) only) Thread size Taper pipe thread ode Size R1/8 R1/4 R3/8 R1/2 6 Parts No code:plug and Socket P:Plug S:Socket (Thread part only)

3 Specifications Fluid medium Air Water (lean water ) eat medium oil ( ) Max. operating pressure 0.9MPa Max. vacuum -100kPa - Operating temp. range 0~60 (No freezing) 0~99 (No freezing) 0~120 (No freezing) Warning. Make sure to follow the instructions below when the fluid medium is water or heat medium oil. 1. Surge pressure must be controlled lower than max. operating pressure when using water or heat medium oil. 2. e sure to place Insert Ring into the tube edge when using water or heat medium oil. FITTING ONTROLLER VALVE TUE onstruction (Elbow: AKL) MAKE-TO-ORDER PRODUTS Tube End Fitting body (Nickel-plated brass) Plug body (Nickel-plated brass) ollet (Nickel-plated brass) Thread body (Nickel-plated brass) Lock-claws (Stainless steel) Release ring (POM) Tube Guide ring (Nickel-plated brass) Elastic sleeve (NR) Sleeve (Nickel-plated brass) O-ring (NR) 246 eat-proof Sealock coating Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling olor ap

4 Fitting Fitting FITTING Detailed Safety Instructions efore using PISO products, be sure to read Safety Instructions and Safety Instruction Manual on page 23 to 27 and ommon Safety Instructions for Fittings on page 33 to 35. Warning 1. efore uncoupling the plug, make sure there is no pressure in the pipe and fluid such as water and heat medium oil are under 30. In case these compressed fluids are still in the pipes and are over 30, there is a possibility that the plug jumps out and cause injury or burns. 2. Do not touch the sleeve when a compressed fluid still remains in the pipe. There is a possibility that plug can be pulled out unexpectedly by touching it physically. 3. When a plug is installed in a socket, push the plug into the socket to fix properly until it stops. It may cause a disconnection of the plug if it is installed incompletely. After installing, pull the plug toward oneself moderately to make sure it is connected properly. 4. Use Nylon Tube N for heat medium oil. e sure to place Insert Ring into the tube edge. There is a possibility to cause the escape of tube and a fluid leakage without Insert Ring. 5. As for barb type, use the I.D.6.3mm-heat-proof hose for ID06 and the I.D.9.5mm-heatproof hose for ID09. Usage of improper size of hoses may result in a poor connection, the escape of hose and a fluid leakage, etc. 6. Make sure to insert the barb into hose up to the barb end and fix it by a hose band which is commercially available. There is a possibility of the hose escape or a fluid leakage by a poor connection of the barb or without the hose band. 247 Standard Mini Stainless aution 1. When the socket is embedded in a molding die, the top surface of the socket must be 3mm deep at maximum from the surface of the die. If the depth is more than 3mm, it can be difficult or impossible to uncouple the plug.. Refer to Die Processing Dimension. hemical PP EG Anti-spatter & rass

5 Standard Size List Tube O.D. (mm) Type Page Thread size AK Straight Tube oms P.251 R1/8 R1/4 R3/8 R1/2 AKL Elbow Tube oms P.252 R1/8 R1/4 R3/8 R1/2 Fitting (Plug) + Thread (Socket) Fitting (Plug) only Thread size (Pipe taper thread) Type Page Thread size Rc1/8 Rc1/4 Rc3/8 AK-F Female Screw oms P.253 R1/8 R1/4 R3/8 R1/2 Tube I.D. (Inch size) Type Page ネジサイズ 1/4 3/8 AK- Straight arb oms P.253 R1/8 R1/4 R3/8 R1/2 FITTING ONTROLLER VALVE TUE Tube O.D. (mm) Type Page AK-P Straight Tube Plug P.254 AKL-P Elbow Tube Plug P.254 Thread (Socket) only Thread size (Pipe taper thread) Type Page R1/8 R1/4 R3/8 R1/2 AK Screw Socket P.256 Thread size (Pipe taper thread) Type Page Rc1/8 Rc1/4 Rc3/8 AK-FP Female Screw Plug P.255 Tube I.D. (Inch size) Type Page 1/4 3/8 AK-P Straight arb Plug P.255 MAKE-TO-ORDER PRODUTS Stop Valve built-in Type: Fitting (Plug) + Thread (Socket) Tube O.D. (mm) Type Page Thread size AS Straight Tube oms P.257 R1/8 R1/4 R3/8 ASL Elbow Tube oms P.257 R1/8 R1/4 R3/8 Thread size (Pipe taper thread) Type Page Thread size Rc1/8 Rc1/4 Rc3/8 AS-F Female Screw oms P.258 R1/8 R1/4 R3/8 Tube I.D. (Inch size) Type Page ネジサイズ 1/4 3/8 AS- Straight arb oms P.258 R1/8 R1/4 R3/8 248 Stop Valve built-in Type: Fitting (Plug) only Tube O.D. (mm) Type Page AS-P Straight Tube Plug P.259 ASL-P Elbow Tube Plug P.259 Screw Socket for Stop Valve built-in Type Thread size (Pipe taper thread) Type Page R1/8 R1/4 R3/8 AS Screw Socket P.261 Thread size (Pipe taper thread) Type Page Rc1/8 Rc1/4 Rc3/8 AS-FP Female Screw Plug P.260 Tube I.D. (Inch size) Type Page 1/4 3/8 AS-P Straight arb Plug P.260 Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling olor ap

6 Fitting Fitting FITTING ow to install and uncouple 1 Drill a hole on a molding die, based on the thread size in advance. See Die Processing Dimension on page 250. Use a hex key to tighten the thread of socket. Installation Thread (Socket) eat-proof Sealock ex key Release-sleeve 2 Plug can be coupled with the socket by inserting only. Fitting (Plug) 3 When uncoupling the plug, firstly push the plug until the release-sleeve stops, then pull it out. Since the socket is embedded in the die and there is no convex projection on the die surface, it is convenient to handle the die. Stop Valve built-in type is useful for safety operation by preventing the fluid from spilling out. Uncoupling 249 Standard Mini Stainless hemical ow to handle 1 Push-In Fitting Place Insert Ring into the edge of Soft Nylon Tube N, and insert the tube into the fitting up to the tube end. Soft Nylon Tube N 3 arb Type for ose Use a heat-proof hose with I.D.6.3mm for ID06 and a heat-proof hose with I.D.9.5mm for ID09. Make sure to insert the barb into hose up to the barb end and fix it by a hose band which is commercially available in order to avoid the hose escape. PP EG Anti-spatter & rass Push-In Fitting Insert Ring 2 Female Screw Type onnectable to taper pipe thread size R1/8, R1/4, R3/8, R1/2. arb type for hose eat-proof hose ose band (commercial product) Taper pipe thread size R1/8, R1/4, R3/8, R1/2 Female Screw Type

7 Die Processing Dimension Drill a molding die as the referential dimensions øp and L in order to embed a socket. L longer than øp Max.3 Rc Model code Rc L ø P AK 08-01S Rc1/ AK 08-02S Rc1/ AK(AS) 10-01S Rc1/ AK(AS) 10-02S Rc1/ AK(AS) 10-03S Rc3/ AK 10-04S Rc1/ FITTING ONTROLLER VALVE TUE Applicable Tube and Related Products Soft Nylon Tube P.608 Insert Ring P.668 Tube Fitting Long Type P.262 MAKE-TO-ORDER PRODUTS 250 Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling olor ap

8 Fitting Fitting FITTING Plug + Socket AK Straight Tube oms L A 251 Standard Mini Stainless Model code Tube O.D. R A L øp Tube end ex. Effective area (V Value) (mm 2 ) AK R1/8 6 AK R1/4 AK R1/8 8 AK R1/4 AK R1/8 AK R1/4 8 AK R3/8 AK R1/2 AK R1/8 AK R1/4 10 AK R3/8 AK R1/2 AK R1/8 AK R1/4 12 AK R3/8 AK R1/2 L is a reference value for height dimension after tightening thread. øp R hemical PP EG Anti-spatter & rass AD AD data is available at PISO website.

9 AKL Model code Elbow Tube oms Tube O.D. R A L øp Tube end E ex. S Effective area (V Value) (mm 2 ) AKL R1/8 6 AKL R1/4 AKL R1/8 8 AKL R1/4 AKL R1/8 AKL R1/4 8 AKL R3/8 AKL R1/2 AKL R1/8 AKL R1/4 10 AKL R3/8 AKL R1/2 AKL R1/8 AKL R1/4 12 AKL R3/8 AKL R1/2 L is a reference value for height dimension after tightening thread. R A øp L S E FITTING ONTROLLER VALVE TUE MAKE-TO-ORDER PRODUTS 252 Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling AD AD data is available at PISO website. olor ap

10 Fitting Fitting FITTING Plug + Socket AK-F Female Screw oms 1 L A 253 Standard Mini Stainless hemical PP EG Anti-spatter & rass øp Model code Rc R A L øp ex. 1 ex. 2 Effective area (V Value) (mm 2 ) AK08-01F01 R1/8 Rc1/8 AK08-01F02 R1/4 AK08-02F01 R1/8 Rc1/4 AK08-02F02 R1/4 AK10-01F01 R1/8 AK10-01F02 R1/4 Rc1/8 AK10-01F03 R3/8 AK10-01F04 R1/2 AK10-02F01 R1/8 AK10-02F02 R1/4 Rc1/4 AK10-02F03 R3/8 AK10-02F04 R1/2 AK10-03F01 R1/8 AK10-03F02 R1/4 Rc3/8 AK10-03F03 R3/8 AK10-03F04 R1/2 L is a reference value for height dimension after tightening thread. Rc AK- Straight arb oms Model code eat-proof hose I.D. R A L øp R 2 ex. Effective area (V Value) (mm 2 ) AK08-ID0601 R1/ AK08-ID0602 R1/4 AK08-ID0901 R1/ AK08-ID0902 R1/4 AK10-ID0601 R1/8 AK10-ID0602 R1/ AK10-ID0603 R3/8 AK10-ID0604 R1/2 AK10-ID0901 R1/8 AK10-ID0902 R1/ AK10-ID0903 R3/8 AK10-ID0904 R1/2 L is a reference value for height dimension after tightening thread. 21 L øp A R AD AD data is available at PISO website.

11 Plug AK-P Model code Straight Tube Plug Tube O.D. øp Tube end ød Recommended socket (thread only) AK08-6P 6 AK08-8P 8 AK10-8P 8 AK10-10P 10 AK10-12P 12. in Recommended socket model code / Replaced with Thread size øp O-ring ød FITTING ONTROLLER VALVE TUE MAKE-TO-ORDER PRODUTS 254 AKL-P Elbow Tube Plug S ød øp O-ring E Model code Tube O.D. øp Tube end E ød S Orifice dia. Recommended socket (thread only) AKL08-6P 6 AKL08-8P 8 AKL10-8P 8 AKL10-10P 10 AKL10-12P 12. in Recommended socket model code / Replaced with Thread size Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling AD AD data is available at PISO website. olor ap

12 Fitting Fitting FITTING Plug AK-FP Female Screw Plug ød Model code Rc øp ex. ød Recommended socket (thread only) AK08-01FP Rc1/8 AK08-02FP Rc1/4 AK10-01FP Rc1/8 AK10-02FP Rc1/4 AK10-03FP Rc3/8. in Recommended socket model code / Replaced with Thread size Rc øp O-ring 255 Standard Mini AK-P Straight arb Plug 21 ød Stainless hemical PP EG Anti-spatter & rass Model code eat-proof hose I.D. øp ød Recommended socket (thread only) AK08-ID06P 6.3 AK08-ID09P 9.5 AK10-ID06P 6.3 AK10-ID09P 9.5. in Recommended socket model code / Replaced with Thread size øp O-ring AD AD data is available at PISO website.

13 Socket AK Screw Socket L A øp2 øp1 R FITTING ONTROLLER VALVE TUE Model code R A L øp1 øp2 ex. AK08-01S R1/8 AK08-02S R1/4 AK10-01S R1/8 AK10-02S R1/4 AK10-03S R3/8 AK10-04S R1/2 L is a reference value for height dimension after tightening thread.. No compatibility with AS (Screw Socket only). MAKE-TO-ORDER PRODUTS 256 Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling AD AD data is available at PISO website. olor ap

14 Fitting Fitting FITTING Stop Valve built-in / Plug + Socket AS Straight Tube oms L A 257 Standard Mini Model code Tube O.D. R A L Tube end ex. Orifice dia. Effective area (V Value) (mm 2 ) AS R1/8 AS R1/4 AS R3/8 AS R1/8 AS R1/4 AS R3/8 AS R1/8 AS R1/4 AS R3/8 AS R1/8 AS R1/4 AS R3/8 ø18 L is a reference value for height dimension after tightening thread. ASL Elbow Tube oms A L R S Stainless hemical R ø18 E PP EG Anti-spatter & rass Model code Tube O.D. R A L Tube end E ex. S Effective area (V Value) (mm 2 ) ASL R1/8 ASL R1/4 ASL R3/8 ASL R1/8 ASL R1/4 ASL R3/8 ASL R1/8 ASL R1/4 ASL R3/8 ASL R1/8 ASL R1/4 ASL R3/8 L is a reference value for height dimension after tightening thread. AD AD data is available at PISO website.

15 AS-F Female Screw oms Model code Rc R A L ex. 1 ex. 2 Effective area (V Value) (mm 2 ) AS10-01F01 R1/8 AS10-01F02 Rc1/8 R1/4 AS10-01F03 R3/8 AS10-02F01 R1/8 AS10-02F02 Rc1/4 R1/4 AS10-02F03 R3/8 AS10-03F01 R1/8 AS10-03F02 Rc3/8 R1/4 AS10-03F03 R3/8 L is a reference value for height dimension after tightening thread. Rc 1 L ø18 A R 2 FITTING ONTROLLER VALVE TUE MAKE-TO-ORDER PRODUTS AS- Straight arb oms L A 258 Model code eat-proof hose I.D. R A L AS10-ID0601 AS10-ID R1/4 ex. R1/8 Orifice dia. Effective area (V Value) (mm 2 ) AS10-ID0603 R3/8 AS10-ID0901 R1/8 AS10-ID R1/4 AS10-ID0903 R3/8 L is a reference value for height dimension after tightening thread. ø18 R Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling AD AD data is available at PISO website. olor ap

16 Fitting Fitting FITTING Stop Valve built-in / Plug AS-P Straight Tube Plug ø8 ø18 Model code Tube O.D. Tube end Recommended socket (thread only) AS10-6P 6 AS10-8P 8 AS10-10P 10 AS10-12P 12. in Recommended socket model code / Replaced with Thread size O-ring 259 Standard Mini ASL-P Elbow Tube Plug S Stainless ø18 hemical ø8 O-ring E PP EG Anti-spatter & rass Model code Tube O.D. Tube end E S Recommended socket (thread only) ASL10-6P 6 ASL10-8P 8 ASL10-10P 10 ASL10-12P 12. in Recommended socket model code / Replaced with Thread size AD AD data is available at PISO website.

17 AS-FP Female Screw Plug Model code Rc ex. Recommended socket (thread only) AS10-01FP Rc1/8 AS10-02FP Rc1/4 AS10-03FP Rc3/8. in Recommended socket model code / Replaced with Thread size Rc ø18 O-ring ø8 FITTING ONTROLLER VALVE TUE MAKE-TO-ORDER PRODUTS AS-P Straight arb Plug ø8 ø18 O-ring Model code eat-proof hose I.D. Recommended socket (thread only) AS10-ID06P 6.3 AS10-ID09P 9.5. in Recommended socket model code / Replaced with Thread size Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling AD AD data is available at PISO website. olor ap

18 Fitting Fitting FITTING Stop Valve built-in / Socket AS Screw Socket ø18 ø15.5 R 23 A L Model code R A L ex. AS10-01S R1/8 AS10-02S R1/4 AS10-03S R3/8 L is a reference value for height dimension after tightening thread.. No compatibility with AK (Screw Socket only). 261 Standard Mini Stainless hemical PP EG Anti-spatter & rass AD AD data is available at PISO website.

19 Safety Instructions SAFETY Instructions This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISO products. e certain to follow ISO 4414 and JIS 8370 ISO 4414:Pneumatic fluid power Recomendations for the application of equipment to transmission and control systems. JIS 8370:General rules and safety requirements for systems and their components. This safety instructions is classified into Danger, Warning and aution depending on the degree of danger or damages caused by improper use of PISO products. Danger Warning aution azardous conditions. It can cause death or serious personal injury. azardous conditions depending on usages. Improper use of PISO products can cause death or serious personal injury. azardous conditions depending on usages. Improper use of PISO products can cause personal injury or damages to properties. 23 Warning 1. Selection of pneumatic products 1 A user who is a pneumatic system designer or has sufficient experience and technical expertise should select PISO products. 2 Due to wide variety of operating conditions and applications for PISO products, carry out the analysis and evaluation on PISO products. The pneumatic system designer is solely responsible for assuring that the user's requirements are met and that the application presents no health or safety hazards. All designers are required to fully understand the specifications of PISO products and constitute all systems based on the latest catalog or information, considering any malfunctions. 2. andle the pneumatic equipment with enough knowledge and experience 1 Improper use of compressed air is dangerous. Assembly, operation and maintenance of machines using pneumatic equipment should be conducted by a person with enough knowledge and experience. 3. Do not operate machine / equipment or remove pneumatic equipment until safety is confirmed. 1 Make sure that preventive measures against falling work-pieces or sudden movements of machine are completed before inspection or maintenance of these machine. 2 Make sure the above preventive measures are completed. A compressed air supply and the power supply to the machine must be off, and also the compressed air in the systems must be exhausted. 3 Restart the machines with care after ensuring to take all preventive measures against sudden movements.. This safety instructions are subject to change without notice.

20 Disclaimer 1. PISO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISO products. 2. PISO does not take any responsibility for any loss caused by natural disasters, fires not related to PISO products, acts by third parties, and intentional or accidental damages of PISO products due to incorrect usage. 3. PISO does not take any responsibility for any loss caused by improper usage of PISO products such as exceeding the specification limit or not following the usage the published instructions and catalog allow. 4. PISO does not take any responsibility for any loss caused by remodeling of PISO products, or by combinational use with non-piso products and other software systems. 5. The damages caused by the defect of Pisco products shall be covered but limited to the full amount of the PISO products paid by the customer. 24

21 Safety Instructions 25 SAFETY INSTRUTION MANUAL PISO products are designed and manufactured for use in general industrial machines. e sure to read and follow the instructions below. Danger 1. Do not use PISO products for the following applications. 1 Equipment used for maintaining / handling human life and body. 2 Equipment used for moving / transporting human. 3 Equipment specifically used for safety purposes. Warning 1. Do not use PISO products under the following conditions. 1 eyond the specifications or conditions stated in the catalog, or the instructions. 2 Under the direct sunlight or outdoors. 3 Excessive vibrations and impacts. 4 Exposure / adhere to corrosive gas, inflammable gas, chemicals, seawater, water and vapor. * * Some products can be used under the condition above(4), refer to the details of specification and condition of each product. 2. Do not disassemble or modify PISO products, which affect the performance, function, and basic structure of the product. 3. Turn off the power supply, stop the air supply to PISO products, and make sure there is no residual air pressure in the pipes before maintenance and inspection. 4. Do not touch the release-ring of push-in fitting when there is a working pressure. The lock may be released by the physical contact, and tube may fly out or slip out. 5. Frequent switchover of compressed air may generate heat, and there is a risk of causing burn injury. 6. Avoid any load on PISO products, such as a tensile strength, twisting and bending. Otherwise, there is a risk of causing damage to the products. 7. As for applications where threads or tubes swing / rotate, use Rotary Joints, igh Rotary Joints or Multi-ircuit Rotary lock only. The other PISO products can be damaged in these applications. 8. Use only Fitting, Tube Fitting Stainless SUS316, Tube Fitting Stainless SUS316 ompression Fitting or Tube Fitting rass under the condition of over 60 (140 F) water or thermal oil. Other PISO products can be damaged by heat and hydrolysis under the condition above. 9. As for the condition required to dissipate static electricity or provide an antistatic performance, use EG series fitting and antistatic products only, and do not use other PISO products. There is a risk that static electricity can cause system defects or failures. 10. Use only Fittings with a characteristic of spatter-proof such as Antispatter or rass series in a place where flame and weld spatter is produced. There is a risk of causing fire by sparks. 11. Turn off the power supply to PISO products, and make sure there is no residual air pressure in the pipes and equipment before maintenance. Follow the instructions below in order to ensure safety. 1 Make sure the safety of all systems related to PISO products before maintenance. 2 Restart of operation after maintenance shall be proceeded with care after ensuring safety of the system by preventive measures against unexpected movements of machines and devices where pneumatic equipment is used. 3 Keep enough space for maintenance when designing a circuit. 12. Take safety measures such as providing a protection cover if there is a risk of causing damages or fires on machine / facilities by a fluid leakage.

22 aution 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a countermeasure, material change from NR to NR or FKM is necessary. onsult with PISO for more information. 4. Special option Oil-free products may cause a very small amount of a fluid leakage. When a fluid medium is liquid or the products are required to be used in harsh environments, contact us for further information. 5. In case of using non-piso brand tubes, make sure the tolerance of the outer tube diameter is within the limits of Table 1. Table 1. Tube O.D. Tolerance mm size Nylon tube Polyurethane tube inch size Nylon tube Polyurethane tube ø1.8mm ±0.05mm ø1/8 ±0.1mm ±0.15mm ø3mm ±0.15mm ø5/32 ±0.1mm ±0.15mm ø4mm ±0.1mm ±0.15mm ø3/16 ±0.1mm ±0.15mm ø6mm ±0.1mm ±0.15mm ø1/4 ±0.1mm ±0.15mm ø8mm ±0.1mm ±0.15mm ø5/16 ±0.1mm ±0.15mm ø10mm ±0.1mm ±0.15mm ø3/8 ±0.1mm ±0.15mm ø12mm ±0.1mm ±0.15mm ø1/2 ±0.1mm ±0.15mm ø16mm ±0.1mm ±0.15mm ø5/8 ±0.1mm ±0.15mm 6. Instructions for Tube Insertion 1 Make sure that the cut end surface of the tube is at right angle without a scratch on the surface and deformations. 2 When inserting a tube, the tube needs to be inserted fully into the pushin fitting until the tubing edge touches the tube end of the fitting as shown in the figure below. Otherwise, there is a risk of leakage. 26 Tube end Sealing Tube is not fully inserted up to tube end. 3 After inserting the tube, make sure it is inserted properly and not to be disconnected by pulling it moderately.. When inserting tubes, Lock-claws may be hardly visible in the hole, observed from the front face of the release-ring. ut it does not mean the tube will surely escape. Major causes of the tube escape are the followings; 1Shear drop of the lock-claws edge 2The problem of tube diameter (usually small) Therefore, follow the above instructions from 1 to 3, even lock-claws is hardly visible.

23 Safety Instructions 7. Instructions for Tube Disconnection 1 Make sure there is no air pressure inside of the tube, before disconnecting it. 2 Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. y insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting 1 When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting a hex key into the inner hexagonal socket of the fitting, be careful so that the tool does not touch lock-claws. The deformation of lock-claws may result in a poor performance of systems or an escape of the tube. 2 Refer to Table 2 which shows the recommended tightening torque. Do not exceed these limits to tighten a thread. Excessive tightening may break the thread part or deform the gasket and cause a fluid leakage. Tightening thread with tightening torque lower than these limits may cause a loosened thread or a fluid leakage. 3 Adjust the tube direction while tightening thread within these limits, since some PISO products are not rotatable after the installation. Table 2: Recommended tightening torque / Sealock color / Gasket materials 27 Thread type Thread size Tightening torque Sealock color Gasket materials M N m SUS304 M ~ 1.5N m NR M6 1 2 ~ 2.7N m Metric thread M ~ 0.6N m M ~ 1.5N m M ~ 1N m POM M ~ 2N m R1/8 7 ~ 9N m Taper pipe thread R1/4 12 ~ 14N m R3/8 22 ~ 24N m White R1/2 28 ~ 30N m Unified thread No.10-32UNF 1.0 ~ 1.5N m SUS304 NR 1/16-27NPT 7 ~ 9N m 1/8-27NPT 7 ~ 9N m National pipe 1/4-18NPT 12 ~ 14N m thread taper 3/8-18NPT 22 ~ 24N m White 1/2-14NPT 28 ~ 30N m These values may differ for some products. Refer to each specification as well. 9. Instructions for removing a fitting 1 When removing a fitting, use proper tools to loosen a hexagonal-column or an inner hex bolt. 2 Remove the sealant stuck on the mating equipment. The remained sealant may get into the peripheral equipment and cause malfunctions. 10. Arrange piping avoiding any load on fittings and tubes such as twist, tensile, moment load, shaking and physical impact. These may cause damages to fittings, tube deformations, bursting and the escape of tubes.

24 Fitting FITTING ommon Safety Instructions for Fittings efore selecting or using PISO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Do not use fittings with fluid medium other than air or water. (Water can be used with some series.) ontact us for using other kind of fluid medium except air and water. 2. Do not use fittings except Anti-spatter, rass and rass ompression Fitting series in a place where the flame and weld spatter is produced. There is a risk of causing fire by sparks. 3.As for applications where threads or tubes swing / rotate, use Rotary Joints, igh Rotary Joints or Multi-ircuit Rotary lock only. The other PISO products can be damaged in these applications Use only Fitting, Tube Fitting Stainless SUS316, Tube Fitting Stainless SUS316 ompression Fitting or Tube Fitting rass under the condition of over 60 (140 F) water or thermal oil. Other PISO products can be damaged by heat and hydrolysis under the condition above. 5.As for the condition required to dissipate static electricity or provide an antistatic performance, use EG fitting and antistatic products only, and do not use other PISO products. There is a risk that static electricity can cause system defects or failures. 6. Avoid any load on PISO products, such as a tensile strength, twisting and bending. Otherwise, there is a risk of causing damage to the products.

25 aution 1.In case of using non-piso brand tubes, make sure the tolerance of the outer tube diameter is within the following limits of Table 1. Table 1. Tube O.D. Tolerance mm size Nylon tube Urethane tube inch size Nylon tube Urethane tube ø1.8mm ±0.05mm ø1/8 ±0.1mm ±0.15mm ø3mm ±0.15mm ø5/32 ±0.1mm ±0.15mm ø4mm ±0.1mm ±0.15mm ø3/16 ±0.1mm ±0.15mm ø6mm ±0.1mm ±0.15mm ø1/4 ±0.1mm ±0.15mm ø8mm ±0.1mm ±0.15mm ø5/16 ±0.1mm ±0.15mm ø10mm ±0.1mm ±0.15mm ø3/8 ±0.1mm ±0.15mm ø12mm ±0.1mm ±0.15mm ø1/2 ±0.1mm ±0.15mm ø16mm ±0.1mm ±0.15mm ø5/8 ±0.1mm ±0.15mm FITTING ONTROLLER VALVE TUE 2. Instructions for Tube Insertion 1 Make sure that the cut end surface of the tube is at right angle without a scratch on the tube surface and deformations. MAKE-TO-ORDER PRODUTS 2 When inserting a tube, the tube needs to be inserted fully into the push-in fitting until the tubing edge touches the tube end of the fitting as shown in the figure below. Otherwise, there is a risk of leakage. Tube end 34 Standard Mini Sealing Tube is not fully inserted up to tube end. 3 After inserting the tube, make sure it is inserted properly and not to be disconnected by pulling it moderately. 3. Instructions for Tube Disconnection 1 Make sure there is no air pressure inside of the tube, before disconnecting it. 2 Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. y insufficient pushing of the release-ring, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. Stainless hemical PP EG Anti-spatter & rass Minimal Stop Fitting Rotary Twist-Proof Fitting lock and onnector oupling olor ap

26 Fitting FITTING 4. Instructions for Installing a fitting 1 When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting a hex key into the inner hexagonal socket of the fitting, be careful so that the tool does not touch lock-claws. The deformation of lock-claws may result in a poor performance of systems or an escape of the tube. 2 Refer to Table 2 which shows the recommended tightening torque. Do not exceed these limits to tighten a thread. Excessive tightening may break the thread part or deform the gasket and cause a fluid leakage. Tightening thread with tightening torque lower than these limits may cause a loosened thread or a fluid leakage. 3 Adjust the tube direction while tightening thread within these limits, since some PISO products are not rotatable the installation. Table 2: Recommended tightening torque / Sealock color / Gasket materials 35 Thread type Thread size Tightening torque Sealock color Gasket materials M N m SUS304 M ~ 1.5N m NR M6 1 2 ~ 2.7N m Metric thread M ~0.6N m M ~1.5N m M ~ 1N m POM M ~ 2N m R1/8 7 ~ 9N m Taper pipe thread R1/4 12 ~ 14N m R3/8 22 ~ 24N m White R1/2 28 ~ 30N m Unified thread No.10-32UNF 1.0 ~ 1.5N m SUS304 NR 1/16-28NPT 7 ~ 9N m 1/8-27NPT 7 ~ 9N m National pipe thread 1/4-18NPT 12 ~ 14N m taper 3/8-18NPT 22 ~ 24N m White 1/2-14NPT 28 ~ 30N m.these values may differ for some products. Refer to each specification as well 5.Instructions for removng a fitting 1 When removing a fitting, use proper tools to loosen a hexagonal-column or an inner hexagonal socket. 2 Remove the sealant stuck on the mating equipment. The remained sealant may get into the peripheral equipment and cause malfunctions. 6.Arrange piping avoiding any load on fittings and tubes such as twist, tensile, moment load, shaking and physical impact. These may cause damages to fittings, tube deformations, bursting and the escape of tubes.