REPLENISHING, OXYGEN SYSTEM - SERVICING

Size: px

Start display at page:

Download "REPLENISHING, OXYGEN SYSTEM - SERVICING"

Asher Wells
6 years ago
Views:

1 REPLENISHING, OXYGEN SYSTEM - SERVICING TASK Quantity Check of the Oxygen System A. Reference Information REFERENCE TASK TASK TASK DESIGNATION Connect and Energize External AC Power Remove External AC Power Servicing of the Oxygen System B. Job Set Up (1) Connect and energize the external ac power (TASK ). (2) Open the oxygen service door that follows: 212BR ACCESS DESIGNATION Door, Oxygen Refill Connection C. Procedure Refer to Figure 301 and Figure 302. (1) At the oxygen refill connection door, examine the pressure gauge (1). Make note of the value shown on the pressure gauge (1). (2) Examine the overboard discharge indicator (2). Make sure that the green disc on the discharge indicator (2) is intact. If the green disk is out, it indicates that an overpressure condition of the oxygen system occurred. NOTE: If an overpressure condition of the oxygen system occurred, return the oxygen cylinder to the authorized facility for servicing. (3) In the flight compartment, do the steps that follow: (a) (b) Examine the oxygen indication on the status page of the engine indication and crew alerting system (EICAS). Compare the indication on the cylinder pressure gauge with the indication on the EICAS readout. Page 301

2 (c) (d) Compare the indication on the cylinder pressure gauge with the indication on the oxygen service door pressure gauge (1). Make sure that the values on the service panel gauge and the EICAS indication are within ±50 psi (344 kpa) of the oxygen bottle gauge. (e) Make sure that the crew oxygen system is fully pressurized (Figure 302). (4) If the oxygen system is not fully pressurized, do the servicing of the oxygen system (TASK ). (5) Make sure that the indications that follow do not show on the status page on the EICAS: LOW OXY PRESS PAX OXY ON (6) Remove the external ac power (TASK ). D. Close Out (1) Remove all tools, equipment, and unwanted materials from the work area. (2) Close the oxygen service door that follows: 212BR ACCESS DESIGNATION Door Oxygen Refill Connection Page 302

3 2 A 1 B C DMM _001 Quantity Check of the Oxygen System Servicing Figure 301 Page 303

4 TEMPERATURE CHART FULLY PRESSURIZED 2000 LIMIT CURVE OXYGEN PRESSURE (PSI) AMBIENT TEMPERATURE IN OXYGEN CYLINDER AREA ( C) DMM _011 Quantity Check of the Oxygen System Servicing Figure 302 Page 304

5 TASK Servicing of the Oxygen System A. Reference Information CL 605 AIRCRAFT MAINTENANCE MANUAL PART II REFERENCE TASK TASK TASK TASK TASK DESIGNATION Remove External AC Power Connect Ground Air Supply Quantity Check of the Oxygen System Pressurize the Air Conditioning System with the Auxiliary Power Unit (APU) Oxygen Safety Precautions B. Tools and Equipment REFERENCE GSE GSE Adaptor, Oxygen System Tag, Circuit Breaker DESIGNATION NOTE: Refer to the Illustrated Tool and Equipment Manual to make sure that you use the correct equipment configuration. C. Consumable Materials REFERENCE DESIGNATION MANUFACTURERS REFERENCE AND/OR SPECIFICATION Oxygen, Aviator s Breathing, Gas MIL O Type 1 Page 305 May 29/2009

6 D. Job Set Up CAUTION: BEFORE YOU REPLENISH THE OXYGEN SYSTEM, MAKE SURE THE AMBIENT TEMPERATURE IS NOT ABOVE 45 C. IF THIS OCCURS, OXYGEN CYLINDER CAN BECOME TOO HOT AND CAUSE DAMAGE TO UNIT. (1) Measure the cabin temperature. If the cabin temperature is above 45 C, cool down the cabin temperature below 45 C using the external ground air supply unit or the APU. NOTE: The cabin temperature can be monitored with the cabin temperature readout on the EICAS multi function display (MFD). or Connect the ground air supply and push in the L and R PACK switch/light (TASK ). Pressurize the air conditioning system with the auxiliary power unit (APU) (TASK ). WARNING: BEFORE YOU DO MAINTENANCE ON THE OXYGEN SYSTEM, MAKE SURE THAT THE EXTERNAL ELECTRICAL POWER IS NOT CONNECTED. MAKE SURE THAT ALL PRIMARY CIRCUIT BREAKERS FOR THE AIRCRAFT BATTERIES ARE OPEN AND SAFETIED. IF YOU ENERGIZE THE ELECTRICAL POWER SOURCE, OR A SPARK OCCURS NEAR AN OXYGEN LEAK, A FIRE/EXPLOSION CAN OCCUR. THIS CAN CAUSE INJURY TO PERSONS, AND DAMAGE TO EQUIPMENT. (2) Make sure that the external ac electrical power is not connected (TASK ). (3) Make sure that the BATTERY MASTER switch in the flight compartment is set to OFF. (4) Open, safety and tag the circuit breakers that follow: LOCATION CB NUMBER CB NAME ZONE CBP 2 M3 BATT BUS POWER SENSE 222 CBP 2 M4 RCCB CONT MAIN BATT 222 CBP 2 M5 RCCB CONT APU BATT 222 CBP 2 M7 FEED 1 BATT BUS 222 CBP 2 M9 FEED 2 BATT BUS 222 Page 306

7 (5) Obey all the oxygen safety precautions (TASK ). (6) Open the oxygen refill connection door (212BR). E. Procedure Refer to Figure 303. WARNING: MAKE SURE THAT HANDS AND CLOTHES OF OPERATING PERSONNEL AND ALL EQUIPMENT, PLUMBING AND FITTINGS USED IN OXYGEN CHARGING ARE COMPLETELY CLEAN OF OIL, GREASE AND SOLVENTS - THESE MAY GET ON FIRE INSTANTLY OR EXPLODE WHEN IN CONTACT WITH HIGH PRESSURE OXYGEN. TO KEEP THE OXYGEN SYSTEM FREE FROM CONTAMINATION, THE FILLER VALVE SHALL BE CAPPED AT ALL TIMES, EXCEPT WHEN CONNECTED TO THE CHARGING CART. CAUTION: THE OXYGEN PRESSURE IN THE CYLINDER MUST NOT BE LESS THAN 50 PSI (345 KPA) AT ANY TIME. IF THIS OCCURS, THE OXYGEN CYLINDER MUST BE REMOVED AND SENT BACK TO THE MANUFACTURER TO BE PURGED. (1) Make sure that each masks are correctly stowed and that the regulators are set to N. (2) Remove the dust cap (1). (3) Install the oxygen system adaptor on the oxygen filler valve (2). (4) Connect the filler line of the oxygen cart to the oxygen system adaptor. CAUTION: MAKE SURE THAT THE OXYGEN SYSTEM PRESSURE IS NOT MORE THAN 1850 PSI (12755 KPA) AT 70 F (21 C). IF THE OXYGEN SYSTEM PRESSURE IS MORE, IT CAN CAUSE DAMAGE TO THE SYSTEM. (5) Charge the oxygen cylinder at a rate not more than 200 psi/min ( kpa/min) until the oxygen cylinder is fully charged as per servicing placard and oxygen pressure gauge (3). NOTE: Make sure to allow a cool down period of 30 to 45 minutes, to make sure that the oxygen system is fully charged. (6) Close the supply valve on the oxygen servicing cart to OFF. (7) Disconnect the servicing cart and oxygen system adaptor from the aircraft. (8) Immediately install the dust cap (1) on the oxygen filler valve. Page 307

8 (9) Remove the tags and close the circuit breakers that follow: LOCATION CB NUMBER CB NAME ZONE CBP 2 M3 BATT BUS POWER SENSE 222 CBP 2 M4 RCCB CONT MAIN BATT 222 CBP 2 M5 RCCB CONT APU BATT 222 CBP 2 M7 FEED 1 BATT BUS 222 CBP 2 M9 FEED 2 BATT BUS 222 (10) Do a quantity check of the oxygen system (TASK ). (11) Close the oxygen refill connection door (212BR). F. Close Out (1) Remove all tools, equipment, and unwanted materials from the work area. Page 308

9 DMM _002 Servicing of the Oxygen System Servicing Figure 303 Page 309

EMERGENCY EQUIPMENT Table of Contents CHAPTER 8 - EMERGENCY EQUIPMENT

Table of Contents 08 00 1 CHAPTER 8 - EMERGENCY EQUIPMENT TABLE OF CONTENTS Page TABLE OF CONTENTS DESCRIPTION General Oxygen System Components and Operation Controls and Indicators Crew Oxygen Consumption