QUICK START GUIDE CB-950 DATA BUOY PLATFORM
|
|
- Alan Hudson
- 10 months ago
- Views:
Transcription
1 What s Included (1) Buoy hull with data well, 950 lb buoyancy (1) Buoy tower (3) 40W Solar panels (1) Data well lid (isic-cb or pass-through) (3) Top-side lifting eyes (3) Bottom-side mooring eyes (1) Instrument cage, large Common Accessories isic-cb data logger enclosure RTU-R/C/I telemetry module CB-A05-2 battery harness/regulator assembly, (2) x 28 A-Hr batteries CB-A05-3 battery harness/regulator assembly, (3) x 28 A-Hr batteries M650H-Y LED beacon RA mini radar reflector 916M 6 sensor deployment pipes CB-PW-AC-60W battery charger Assembly Overview Figure 1: CB-950 Data Buoy Overview The NexSens CB-950 data buoy platform is constructed with a closed cell, cross-linked polyethylene foam hull with polyurea coating that provides 950 lb buoyancy. The buoy has a corrosion resistant, stainless steel internal frame with topside lifting eyes and subsurface mooring eyes for connection of single-point and multipoint mooring systems. An integrated data well located within the buoy hull accommodates batteries and electronics. The data well lid is available as a NexSens isic-cb data logger assembly or as a standard lid with pass-through fittings for use with user-supplied electronics. Internal batteries are recharged by (3) 30-Watt solar panels mounted on the buoy tower, which also supports an optional LED beacon, radar reflector, and RTU-R/C/I radio, cellular or Iridium satellite telemetry module. The main components of the CB-950 data buoy platform are assembled at the time of shipment. Installation of accessories may be required. Quick instructions are provided in this guide. Visit the online Knowledge Base for more information (see Additional Information section). Instrument Cage The instrument cage is connected to the buoy using a CB-CCA cage clamp accessory. Reference the instructions provided with the clamp for installation. Welding the cage and/or installing additional security straps is also recommended for use in rough water. Figure 2: Cage with CB-CCA Clamp 1
2 Solar Tower The top plate of the solar tower has hole patterns designed for mounting of an M650 beacon, RTU- R/C/I telemetry module, RA mini radar reflector, and/or a weather sensor mount. These devices are typically mounted on the tower in the factory prior to shipment. Make any changes or additions prior to installation of the tower onto the buoy. Figure 5: Locking Pin and Tower Mount Hub Figure 3: Tower with Beacon and Radar Reflector Deployment Pipe Figure 6: Installed Tower The bottom of the buoy hull includes (3) 6 female threaded couplings for connection of NexSens 916M deployment pipe assemblies or other PVC fittings. To use these ports, simply thread each deployment pipe securely into one of the available couplings. Figure 4: Tower with Beacon and RTU-C Module When the tower is ready to be mounted, remove the locking pin from each of the three tower mounting hubs on top of the buoy hull. Place the tower legs into the hubs and secure the locking pins. Instruments deployed in 916M pipes can easily be accessed for calibration and maintenance by removing the port cover plate from the top of the buoy hull. Use a 5/16 Allen/hex key to remove the set of screws on the cover plate. 2
3 Wiring & Device Connections NexSens isic-cb Data Well Lid each other if both are connected to P0. RS-485 and SDI-12 ports are shared throughout the bus. For systems using NexSens electronics for data acquisition and telemetry, the isic data logger is housed in an isic-cb enclosure that provides a watertight seal over the data well. The bottom of the isic-cb has a power plug that connects to a CB-A05-2/3 battery/solar regulator assembly. The top of the isic-cb enclosure has a series of UW ports for connection of solar panels, sensors, communication devices, and external power supplies to the isic. The available ports and functions are: - (5) SENSOR (P0/P1/P2): NexSens sensorbus architecture includes wiring for SDI-12, RS- 232 and RS-485 devices. For compatibility, sensors must have a factory-installed UW plug connector. The sensor ports are wired as follows: (2) P0: 12V full power, shared RS-232 port. (2) P1: 12V switch power, shared RS-232 port. (1) P2: 12V switch power, unique RS-232 port. - (1) COM: Communications port for isic data logger configuration and data acquisition through UW-USB-232P-NP cable or RTU-R/C/I radio, cellular, or Iridium satellite telemetry module. - (1) SOLAR: 6-pin input for solar panel to apply system power and charge internal battery. Solar cable or a specialized UW plug with jumper (P/N UW-JUMPER) must be connected to SOLAR port to power the isic. - (1) VENT: Gortex vent for relief of outgassing pressure during recharge of batteries located in the data well. In heavy wave conditions, this vent can be plumbed with tubing to the top of the tower. The sharing of RS-232 ports on P0 and P1 means that only one non-addressable device can be connected at a time. For example, two devices with RS-232 NMEA0183 output will interfere with Figure 7: isic-cb Enclosure Devices with analog outputs (e.g ma, VDC) may be connected to the isic-cb through a mv-rs485 adapter, which converts the analog signal to RS-485 Modbus. The mv-rs485 adapter must be programmed for the specific sensor connected. See the instructions provided with the adapter for more information. Figure 8: mv-rs485 Adapter 3
4 Table 1 shows the sensorbus signal for each pin on the UW receptacle ports of the isic-cb. The pins are numbered based on the diagram in Figure 9 (plug pins are 1-4, socket pins are 5-8). The table also lists the corresponding wire color for a UW plug to flying lead cable connected to a port (see Figure 10). The system battery voltage can be checked externally by placing the leads of a voltmeter on pins 4 (red) and 7 (black) of a P0 or COM port. Table 1: UW Receptacle sensorbus Wiring UW Receptacle Pin Wire Color sensorbus Signal 1 Green RS-485 A 2 Blue RS-485 B 3 Brown SDI-12 4 Red 12V Power 5 White 5V Power 6 Yellow RS-232 Rx 7 Black GND 8 Orange RS-232 Tx Figure 10: UW Plug to Flying Lead Cable Pass-Through Data Well Lid For applications with user-supplied sensors, data loggers, telemetry modules and/or batteries, the CB-950 data buoy is provided with a data well lid with a set of plugs and pass-through fittings for securing user-supplied instrument cables. The lid includes the following ports: - (6) PASS-THROUGH: Blank UW receptacles supplied with a set of plugs for sealing unused ports and a set of fittings for securing instrument cables going into the data well. - (1) SOLAR: 6-pin port for connection of solar panel assembly. Includes connector inside data well for use with optional CB-A05-2/3 battery/solar regulator harness. For use with user-supplied battery/regulator systems, see Solar Power Wiring. - (1) VENT: Gortex vent for relief of outgassing pressure during recharge of batteries located in the data well. Tighten the fittings securely around cables routed into the data well to maintain the watertight seal. Plug all ports that are not used. Figure 9: UW Connector Pinout 4
5 For a more robust connection at the data well plate, the pass-through ports may be fitted with UW-BULK bulkhead receptacle connectors. The UW-BULK assembly has the same pinout as isic- CB sensor ports (see Table 1), but the cable terminates in flying leads for integration with a user-supplied data logger. The device connected must have a factory-installed UW connector. Figure 11: UW-Bulkhead Connector Assembly Solar Power Wiring Figure 12 shows a schematic drawing for the wiring of the CB-950 power supply. The system includes (3) 30-watt solar panels that connect through the SOLAR port on the data well plate to the CB-A05-2/3 or user-supplied battery/solar regulator harness. A wire lead is provided to supply 12V DC power to electronics inside the data well (red = +12V, black = GND). Figure 12: Wiring Schematic *NOTE: The 12V power supply leads for user supplied electronics will only supply power when the solar panel is plugged into the SOLAR port on the data well lid, even if a battery is connected inside the data well. To supply battery power without plugging in the solar panel, a special UW plug with internal jumper is available (P/N UW- JUMPER). For systems with user-supplied battery and solar regulator, the battery and regulator can be connected through the 4-pin Molex connector or by cutting the wires at section A-A in Figure 12 and splicing the connections. In these situations, reference the signals listed in Table 2. 5
6 Table 2: Wiring for user-supplied battery/regulator Signal Wire Color +12V Red GND Black Solar input Yellow Charge output Orange cage. Figure 13 shows an example of a buoy system with a short section of chain added. The buoy data well is not rated for submersion, so proper ballast weight is critical to ensure that the buoy does not overturn, including when the buoy is subjected to additional loading (e.g. high wind/waves, periodic snow/ice loads, etc.). Ballast Weight and Stability To prevent overturning of a CB-950 buoy system and to ensure that it is stable in the water, a minimum ballast weight of 125 lbs. is needed for calm deployment locations and more in rough waters. The center of gravity of the buoy is somewhere near the water surface without instruments connected. Any weight added above the water surface must be appropriately counterbalanced by adding ballast weight below the surface. The larger the distance from the location of added weight to the center of gravity, the greater the effect on the stability of the buoy will be. For example, if a weather sensor is mounted 36 above the water surface, it will cause more instability than if it were mounted 24 above the surface and, as a result, would require more subsurface ballast weight to counterbalance the buoy. Conversely, a ballast weight added further below the surface will provide a greater stabilizing effect than the same size weight mounted closer to the surface. An instrument cage mounted to the buoy frame helps to stabilize the buoy and provides a deeper location for mounting additional weight. For single-point mooring configurations, mooring chain and lines connected to the bottom of the cage may provide adequate ballast. For multipoint configurations, the mooring hardware does not contribute to the ballast weight. Before deployment of a CB-950 system, some experimentation may be required to properly balance the buoy. If needed, add ½ chain (~2.3lb/ft) or other weight to the bottom of the Figure 13: CB-950 Data Buoy with Ballast Chain Saltwater Deployment Sacrificial zinc anodes should be used whenever a buoy is deployed in a saltwater environment to prevent corrosion. These zinc anodes must be inspected and replaced as needed. 6
7 Mooring Configurations This section contains only general information on the available mooring options for CB-950 data buoys. To develop an effective mooring strategy, a variety of application-specific criteria (water level fluctuations, currents and wave action, debris loads, etc.) must be thoroughly reviewed prior to deployment. NexSens does not endorse any particular mooring strategy for any specific application. Single-Point Mooring Single-point moorings are used in calm waters when monitoring sensors are attached to the instrument cage or housed in deployment pipes. The sensors are thus protected and less vulnerable to damage caused by subsurface debris, high currents, and entanglement from anchor lines. In a single-point configuration, a stainless steel mooring line connects the buoy directly to a bottom chain and anchor. At normal pool/stage, the mooring line should be taut, with most of the bottom chain resting on the floor of the water body. As the water level increases and the buoy rises, the bottom chain is lifted from the floor. Two-Point Mooring Two-point moorings are commonly used when monitoring sensors are deployed in the water column below the buoy. In this setup, the mooring lines are pulled taut away from the buoy, freeing the water column for a suspended sensor line. In most two-point configurations, mooring lines connect the data buoy to small marine marker floats, often located on the water surface. These marker floats are shackled to another mooring line that runs to the floor and connects to a bottom chain and anchor assembly. Additional subsurface marker floats may also be used in some applications. As in single-point systems, the bottom chain prevents buoy submersion as the water level fluctuates. Figure 15: Typical Two-Point Mooring Configuration Figure 14: Typical Single-Point Mooring Configuration 7
8 Safe Deployment Personnel safety is the number one priority when deploying a data buoy. Use of proper equipment (work boat, lifting rig, gloves, safety footwear, etc.) is essential to safely deploy any buoy system. Buoy systems are heavy and personnel can quickly become entangled with mooring lines and anchors. Safety and flotation gear should be worn at all times when working on or near the water. Remember to perform a complete system test on shore prior to deployment. Learning the nuances of the system is much better handled on shore or in a lab rather than in the field. Specifications Hull Dimensions: 42 (106.70cm) outside diameter; 26 (66.04cm) tall Tower Dimensions: 45 (114.30cm) tall, 7/8 tubular Data Well Dimensions: 10.3 (26.16cm) inside diameter; 25.5 (64.77cm) tall Weight: 285 lbs. ( kg) Buoyancy: 950 lbs. ( kg) Hull Material: Cross-linked polyethylene foam with polyurea coating & stainless steel deck Tower/Hardware Material: 304 stainless steel Other Material: Galvanized ballast chain Mooring Attachments: 1- or 2-point, ¾ eye nut Solar Power: (3) 40-watt, 12VDC solar panels Additional Information Additional information and complete instructions for the CB-950 data buoy platforms are available in the NexSens online Knowledge Base: 8
Mini-Pro CO2 Sensor User s Manual - ANALOG MODEL -
Mini-Pro CO2 Sensor User s Manual - ANALOG MODEL - Table of Contents 1. Introduction 3 2. Instrument Setup 4 2.1 Instrument Checklist 4 2.2 Optional Accessories 4 2.3 Gas Concentration Ranges Available
CLIENT NAME: LOCATION: CALM BUOY INSPECTION:
INSPECTOR REVIEWED INSPECTION OF CALM BUOY OVERALL PHOTO REVISION DESCRIPTION: Preliminary / Final Page: 1 TABLE OF CONTENT 1. MANAGEMENT SUMMARY... 3 1.1. SCOPE OF WORK:... 3 1.2. CORRECTIVE ACTIONS...
Pressure Measurement Single-range transmitters for general applications
Siemens AG 07 Overview Function U const. p U I EM Sensor Connection for auxiliary power supply Vent pipe with humidity filter Protective conductor connection/ Equipotential bonding Diaphragm The pressure
GasSense NDIR User Manual
INDEX INDEX... 1 1. OVERVIEW... 2 2. TECHNICAL DATA... 3 3. SPECIFICATIONS... 4 4. PRODUCT DESCRIPTION... 5 4.1 Mechanical details... 5 4.2 Piping... 7 4.3 Connections... 7 5. INSTALLATION... 10 6. CALIBRATION
UBEC 1AT. AUTO TANK Fill System Installation, Operation, & Setup Instructions
Document Number: XE-ATA5PM-R1A UBEC 1AT AUTO TANK Fill System 08899155 Installation, Operation, & Setup Instructions Rev170906-EB-FRC PHYSICAL: 1302 WEST BEARDSLEY AVE ELKHART, IN 46514 WWW.ELKHARTBRASS.COM
I.H.S INSTALLATION INSTRUCTIONS
I.H.S INSTALLATION INSTRUCTIONS TOOLS REQUIRED The following tools will be required for installation of your I.H.S. system. Item Qty Needed 9/16 Open End Wrench 2 3/4 Open End Wrench 1 1/2 Open End Wrench
Pressure Measurement Single-range transmitters for general applications
Siemens A 207 Overview Application The SITRANS P Compact pressure transmitter is designed for the special requirements of the food, pharmaceutical and biotechnology industries. The use of high-grade materials
Expert Hydrostatic Level Transmitters
Expert Hydrostatic s General Features MJK Expert hydrostatic level transmitters are designed for level measurement by submerging the transmitter in open channels, drains and tanks. Expert hydrostatic level
Assembly Instructions. -Cantilever Boat Lifts
Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for
Technical Information Conducal CLY421
TI00496C/07/EN/01.12 71142150 Products Solutions Services Technical Information Conducal CLY421 Conductivity calibration set for ultrapure water applications Factory calibrated measurement box Certified
TRANSDUCER KIT 2 INSTALLATION INSTRUCTIONS
TRANSDUCER KITS INSTALLATION INSTRUCTIONS ELECTRICAL SHOCK HAZARD Disconnect power before installing or servicing this product. A qualifi ed service person must install and service this product according
BUYER S GUIDE AQUAlogger 520
OCEAN & ENVIRONMENTAL BUYER S GUIDE AQUAlogger 520 Mini Temperature and Pressure Logger AQUAlogger 520 Aquatec s primary temperature and depth model, the AQUAlogger 520, combines years of product development
MODEL ANALOG ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.2 TO 100FT OPERATING RANGE ANALOG OUTPUT
MODEL 862-000-200 ANALOG ALTIMETER USER'S MANUAL 330KHZ, 1000M DEPTH RATED 0.2 TO 100FT OPERATING RANGE ANALOG OUTPUT DOCUMENT NO. 430-007H September 20, 2005 S/N IMAGENEX TECHNOLOGY CORP. 209-1875 BROADWAY
AUTO PUMP STATUS CENTER
INSTRUCTION MANUAL AUTO PUMP STATUS CENTER PRESSURE ONLY MODEL #: 091-198-12-AP File: IM_091-198-12-AP_revD.indd Rev: D, pg 3 WD Revised By: PSS Date: 2-01-2016 3 YEAR WARRANTY INTRODUCTION The Auto Pump
Copyright 2004 by the Thomas G. Faria Corporation, Uncasville CT No part of this publication may by reproduced in any form, in an electronic
Copyright 2004 by the Thomas G. Faria Corporation, Uncasville CT No part of this publication may by reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission
Foundation Products. Poured In Ground Anchor Bolts E1 - E4. Structural Foundations E5 - E12. Copyright 2016 s Industry Inc. SIE-RA-CMP EN
Foundation Products Poured In Ground Anchor Bolts E1 - E4 Structural Foundations E5 - E12 EA EB Poured in Ground Anchor Bolts Layout SIEMENS Anchor Bolts 131702-4X shown for reference purposes only! Actual
EcoPRO-Series 4-20mA SUBMERSIBLE PRESSURE TRANSMITTER INSTRUCTIONS
EcoPRO-Series 4-20mA SUBMERSIBLE PRESSURE TRANSMITTER INSTRUCTIONS EcoPRO-Series 4-20mA SUBMERSIBLE PRESSURE TRANSMITTER INSTRUCTIONS 9001:2008 ISO CERTIFIED COMPANY Table of Contents Introduction - EcoPRO-Series
Pneumatic spool valve islands
Pneumatic spool valve islands P7.GB.R MEGA SPOOL VALVE ISLANDS MEGA pneumatic spool valve islands offer maximum performance along with flexibility, easy installation and simple operation. Due to their
Energy Management solutions for compressed air and industrial gases. vpinstruments.com
Energy Management solutions for compressed air and industrial gases vpinstruments.com 6 Introduction VPINSTRUMENTS Measure, Discover and Save! Compressed air is a very expensive energy source. In fact,
RPS900W Redundant Power Supply. Installation Guide.
RPS900W Redundant Power Supply Installation Guide www.edge-core.com Installation Guide RPS900W Redundant Power Supply Single DC Output Port with Dual Output Voltages RPS900W E10013-CS-R01 1500000081A
KEG PUMP. Range of Electric Keg Pumps
KP KEG PUMP Range of Electric Keg Pumps Electric Keg (Drum) Pumps for Grease KEG PUMP Versatile range of Interlube electric grease pumps for industrial and off-road applications The KP keg pump is available
HUMOR 20. High-precision Humidity Calibrator HUMOR 20. Operation
High-precision Humidity Calibrator The role of humidity calibrations that are accurate, reproducible, and documentable is becoming more and more important. ISO quality guidelines and regulations according
L3 Pressure and Level transmitter
SENSORS FOR AND BIOPHARMA. Product Information L3 L3 Pressure and Level transmitter Range of applications Hydrostatic Level measurement in dynamic temperature environments Pressure measurement in pipes
AMS 2710 PCB pressure sensor module with V output
FEATURES Universal pressure sensor module with 0.. 10 V voltage output Fully calibrated and temperature compensated sensor module Variants for (bidirectional) differential, gage, absolute and barometric
Proportional pressure regulators VPPE
Proportional pressure regulators VPPE Proportional pressure regulators VPPE Product range overview Function Version Pneumatic connection Proportional pressure regulator Nominal size for pressurisation/
Installation, operating and maintenance Instructions for Seemag bypass level indicator
Issue: S Date: 05-09-14 Type G35 General information The Seetru bypass magnetic level indicator, abbreviate SEEMAG, serves to show the filling level of fluids in tanks, basins, tubes etc. The Seemag operates
Z, Y, and X PURGE INDICATORS / CONTROLLERS
PurgEx XXXXXX Z, Y, and X PURGE INDICATORS / CONTROLLERS PURGE / PRESSURIZATION PURGE / PRESSURIZATION XXXXX XXXXXXXXX 8626 SERIES Globally Certified Z,Y,X Purge Indicators / Controllers and Accessories
MEASUREMENT COMMUNICATION INSIGHT
Temperature & Depth MEASUREMENT COMMUNICATION INSIGHT CONTENTS Introduction to Aquatec Measuring Temperature and Depth 2 3 Aquatec s Temperature and Depth Loggers AQUAlogger 520 AQUAlogger 530 AQUAlogger
Instructions. Table of Contents
Instructions Table of Contents Hardware and Controls... Base station front face... 4 Side panel... 6 Fencer pack... 7 Radio link and sync process... How to sync packs to the base station... 8 Radio channel...
Stand-Alone Bubble Detection System
Instruction Sheet P/N Stand-Alone Bubble Detection System 1. Introduction The Bubble Detection system is designed to detect air-bubble induced gaps in a bead of material as it is being dispensed. When
EPP4 Pressure Regulator Basic G 1/4"
EPP4 Pressure Regulator Basic G 1/4" Flow Curve 1/4" Dimensions Outlet pressure - bar 9 8 7 6 5 4 3 2 1 0 0 20 40 60 70 80 100 120 Flow rate - Nm 3 /h The male connector adopted on the EPP4 is a standard
HUMOR 20. High Accuracy Humidity Calibrator. Water T, p1 HUMOR 20 V1.0
High Accuracy Humidity Calibrator The role of humidity calibrations that are accurate, reproducible, and documentable is becoming more and more important. ISO quality guidelines and regulations according
Pressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
TECHNICAL DATA. Trimpac 257a. September 16, 2013
September 16, 2013 Trimpac 257a 1. DESCrIpTION DESCRIPTION The Viking Double SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-2 and D-2B used with either a Model E or F Deluge Valve (A.1), a Viking
Level transmitter LT 100
KROHNE 09/2001 7.02363.21.00 GR/PRINTO Level transmitter LT 100 Status: 10/99 Variable area flowmeters Vortex flowmeters Flow controllers Electromagnetic flowmeters Ultrasonic flowmeters Mass flowmeters
TECHNICAL DATA. Trimpac 256a. October 31, 2013
October 31, 2013 Trimpac 256a 1. DESCRIPTION The Viking SUREFIRE SIngle Interlock Preaction TRIMPAC Model D-1 and D- 1B used with either a Model E or F Deluge Valve (A.1), a Viking Easy Riser check valve
! WARNING. Model PFC-1-G (direct acting) PFC-1-GR (reverse acting) Modulating Pneumatic Liquid Level Controls INSTRUCTION MANUAL MM-110B
INSTRUCTION MANUAL MM-110B Model PFC-1-G (direct acting) PFC-1-GR (reverse acting) Modulating Pneumatic Liquid Level Controls APPLICATIONS: Use with other pneumatic devices, for liquid level sensing in
PRO-50 Instrument Supply Regulator
Features CRN Approved The PRO-50 Regulator has been granted a Canadian Registration Number. Sour Service Capability Available in NACE configurations that comply with NACE MR0175/MR0103. Environmental limits
Horizontal Bladder Tanks
DATA SHEET Horizontal Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
Lectric Cycles Mid-Drive Electric Motor Installation
Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on
INTRODUCTION TO NETWORK WIND 3 MOUNTING THE UNIT 14 SELECTING THE DISPLAY MODE 5 ABBREVIATIONS AND DEFINITIONS 17
CONTENTS CONTENTS 1 INSTALLATION 14 GENERAL INTRODUCTION TO B&G NETWORK 2 SITING THE UNIT 14 INTRODUCTION TO NETWORK WIND 3 MOUNTING THE UNIT 14 EXAMPLE SYSTEMS USING NETWORK WIND 4 SPECIFICATION 16 SELECTING
Model MTB-ASME Vertical Bladder Tanks
DATA SHEET Model MTB-ASME Vertical Bladder Tanks Features n UL Listed for use with various proportioners and foam concentrates n 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
MJK Expert 700 / 800 / 900 / 7070 / 7060 MJK Expert 1400 / 3400
MJK Expert 700 / 800 / 900 / 7070 / 7060 MJK Expert 1400 / 3400 Submersible Hydrostatic s Rugged and versatile 2.75 GB 2.75 Expert 090311 We reserve the right to continuously improve our products and make
Vertical Bladder Tanks
DATA SHEET Vertical Bladder Tanks Features UL Listed and FM Approved for use with various ANSUL proportioners and foam concentrates 175 psi (12.1 bar) maximum allowable working pressure (design pressure)
PT-500 Modbus Series User Manual APG
PT-500 Modbus Series User Manual APG R Doc #9003999 Rev A, 02/15 Table of Contents Introduction... iii Warranty and Warranty Restrictions... iv Chapter 1: Specifications and Options... 1 Dimensions...1
PULSAR 5000 SERIES OPERATING & INSTALLATION INSTRUCTIONS SERIES 5000 PLEASE READ CAREFULLY BEFORE INSTALLING
PULSAR 5000 SERIES OPERATING & INSTALLATION INSTRUCTIONS SERIES 5000 PLEASE READ CAREFULLY BEFORE INSTALLING Please Note: Ranges above 500mbar are designed and manufactured in accordance with sound engineering
JUMO dtrans p30 Pressure Transmitter
609 Fulda, Germany Postal address: 605 Fulda, Germany Phone: +49 661 600-0 Fax: +49 661 600-607 Phone: +44 179 6 55 Data Sheet 40466 Page 1/6 JUMO dtrans p0 Pressure Transmitter General application Pressure
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)
Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk WIRE ROPE GRIPPER WGO135 (without manifold and intensifier) PRODUCT
Exercise 5-2. Bubblers EXERCISE OBJECTIVE DISCUSSION OUTLINE. Bubblers DISCUSSION. Learn to measure the level in a vessel using a bubbler.
Exercise 5-2 Bubblers EXERCISE OBJECTIVE Learn to measure the level in a vessel using a bubbler. DISCUSSION OUTLINE The Discussion of this exercise covers the following points: Bubblers How to measure
RC 195 Receiver-Controller
Document No. 129-082 RC 195 Receiver-Controller Product Description The POWERS RC 195 Receiver-Controller is a pneumatic instrument that receives one, two or three pneumatic inputs. It produces a pneumatic
RAI-M series RUDDER ANGLE INDICATOR SYSTEM
RUDDER ANGLE INDICATOR SYSTEM RAI-M series SEAFIRST ENGINEERING CO 45-16, Ga Um Dong, Chang Won, Kyong Nam Korea Tel : 82 55 267 1645 Fax ; 82 55 266 1646 http://www.seafirst.co.kr GENERAL Seafirst Rudder
MUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.
Installation Instructions manual MUELLER table of contents PAGE A-20808 General Information 2 Technical Data 3 Dimensions 4 A-20809 Non-Adjustable Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator
Standard and Low-Flow Metric Powder Feed Pumps
Instruction Sheet P/N 06699E Standard and Low-Flow Metric Powder Feed Pumps Introduction Standard and low-flow metric powder feed pumps are used to deliver organic and metallic powder coatings to powder
660 Multipoint Electronic Level Switch
660 Multipoint Electronic Level Switch General Instructions The Multipoint Electronic Level Switch is a level sensing device which reads process level by capacitance measurement. Capacitance varies according
Wildcat LB Winch Kit. Operator s Manual Installation Instructions Replacement Parts List. With Wireless Control System.
p/n 2259-560 Wildcat 4000 LB Winch Kit With Wireless Control System Operator s Manual Installation Instructions Replacement Parts List 2012 Arctic Cat Inc. Trademarks of Arctic Cat Inc. Thief River Falls,
MANUAL KPS Pressure Control Valve
TetraTec Instruments GmbH Gewerbestrasse 8 71144 Steinenbronn Deutschland E-Mail: info@tetratec.de Tel.: 07157/5387-0 Fax: 07157/5387-10 MANUAL Pressure Control Valve *** VERSION 1.0 *** Update: 17.11.2006
AMC-400 Series. Digital Transmitter with Smart Sensor USER MANUAL
AMC-400 Series Digital Transmitter with Smart Sensor USER MANUAL IMPORTANT: Please read the installation and operating instructions completely and carefully before starting. Filename: 3242405A_4.doc Copyright,
Types and approvals. Page 1/6. Data Sheet
Page 1/6 Panel-mounting Thermostats EM Series as: Protection temperature monitor STW (STB) Protection temperature limiter STB tested to DIN 3440 and Pressure Equipment Directive 97/23/EC Brief description
MUELLER. A A Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.
Installation Instructions manual MUELLER table of contents PAGE A-20806 A-20807 Adjustable General Information 2 Technical Data 3 Dimensions 4 Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator
DeltaSpan General Purpose Water Small Bore or Wastewater Pressure Level Transmitter LD34 and LD35 Series Manual
DeltaSpan General Purpose Water Small Bore or Wastewater Pressure Level Transmitter LD34 and LD35 Series Manual LD34 Series Shown LD35 Series Shown Flowline, Inc. 10500 Humbolt Street Los Alamitos, CA
Draft of OKMC Cruise Plan (R/V Revelle June 1-14, 2012 RR1205)
Draft of OKMC Cruise Plan (R/V Revelle June 1-14, 2012 RR1205) Ren-Chieh Lien and Thomas B Sanford 1. Objectives In the RR1205 cruise, we will deploy five subsurface moorings, one surface mooring (TBD),
For ANCHOR WINCH Model: T Big Water 45 T sw Salt Water Series Big Water 45
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ANCHOR WINCH Model: T10110-45 Big Water 45 T10103-45sw Salt Water Series Big Water 45 If you have any questions or difficulty installing this
LVU2800 Series. Ultrasonic Level Transmitter
LVU2800 Series Ultrasonic Level Transmitter 2 of 23 INTRODUCTION / TABLE OF CONTENTS Step One The LVU2800 Series is a general purpose ultrasonic level transmitter that provides a loop powered 4 20 ma output.
SIMPLAIR PIPING TOOL. JXT Company
SIMPLAIR PIPING INGERSOLL-RAND SIMPLAIR PIPING With push-in fittings and lightweight anodized aluminum pipe, a SimplAir system provides ideal connection throughout your entire air distribution system.
The M-Series Eletta Flow Meter High accuracy DP Flow Meter with multiple functions
The M-Series Eletta Flow Meter High accuracy DP Flow Meter with multiple functions Flow Meter with multiple functions for gases and liquids M3 The M-series Flow Meter, with its versatile and user-friendly
Test and Adjustment Instructions Compressed Air Processing System Air Processing Unit (APU)
Test and Adjustment Instructions Compressed Air Processing System Air Processing Unit () 1st issue 8150004983 815 000 498 3 This document is not covered by a revision service. New versions can be found
Additel 761 Automated Pressure Calibrators Selection Guide
/ Process Calibration Equipment Automated Calibrators Selection Guide Model Features Range Module 1 761-LLP 761-D 761-L 761-LA 761-M 761-MA 761-H 761-HA 761-BP -2.5 to 2.5 mbar (-1 to 1 inh 2 O) -0.95
Analogue and Digital Mass Flow Meters and Controllers for Gases MASS-STREAM
Analogue and Digital Mass Flow Meters and Controllers for Gases MASS-STREAM M+W Instruments Your partner Key Facts M+W Instruments was founded in 1988 and has always specialised in thermal mass flow meters
SECURITY AND CONFIDENCE AT HEIGHT
Detachable Cable Sleeve SECURITY AND CONFIDENCE AT HEIGHT THE ULTIMATE IN FALL PROTECTION THE DANGERS OF WORKING AT HEIGHT Every day, workers around the world climb ladders to great heights to get their
10.2. Basketball Single Post System
Basketball Basketball Single Post System The single-post basketball stand is made with oval aluminium profiles with a cross-section of 120 x 100 mm. The wall thickness of this robust apparatus is 4 to
INSTRUCTION MANUAL Pressure Relief Device LPT
INSTRUCTION MANUAL Pressure Relief Device LPT 5COV475800 LPT REV00 CONTENT: 1 SAFETY 1.1 Safety instructions 2 1.2 Specified applications 2 1.3 Safety notes on the equipment operation 2 2 PRESSURE RELIEF
NEXT EXIT THE GREAT OUTDOORS POPULATION: EVERYONE
2017 NEXT EXIT THE GREAT OUTDOORS POPULATION: EVERYONE SportRack is proud to offer safe, quality products that allow you to take full advantage of your vehicle s carrying capacity. SportRack accessories
TOWER INSPECTION REPORT
3010 S. Hwy 77, Suite 600 Waxahachie, Texas 75165 http://ctctower.com Office: 972/923-9504 Fax: 972/923-9619 TOWER INSPECTION REPORT PREPARED FOR MR. CUSTOMER 1,563 GUYED TOWER NEAR CITY, STATE JANUARY
INSTALLATION PROCEDURE 1/4 & 1/8 MILE PERMANENT TRACK
INSTALLATION PROCEDURE 1/4 & 1/8 MILE PERMANENT TRACK 1) Unpack all of the equipment and immediately inspect for shipping damage. Damages should be immediately reported to the carrier and noted on the
INSTALLATION & OPERATION MANUAL. Dual Duct VAV Terminals. Redefine your comfort zone.
INSTALLATION & OPERATION MANUAL Dual Duct VAV Terminals IOM Dual Duct VAV Terminals IMPORTANT! READ BEFORE PROCEEDING! GENERAL SAFETY GUIDELINES This equipment is a relatively complicated apparatus. During
TECHNICAL DATA. Trimpac 244a. September 16, 2013
September 16, 2013 Trimpac 244a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-1 and B-1B is a factory-assembled trim package with an electric release module in a metal enclosure. The standard trim normally
WINCH USER GUIDE WARN 3700 Utility Winch Part Number: 93700
WINCH USER GUIDE WARN 3700 Utility Winch Part Number: 93700 Your safety, and the safety of others, is very important. To help you make informed decisions about safety, we have provided installation and
User Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
ED 701 Hygenic Pressure Transmitter
ED 701 Hygenic Pressure Transmitter Hygienic process connections Complete range of electrical connections 4... 20 ma and Voltage outputs Accuracy: 0.1%, 0.2% and 0.4% FS Quick response time < 25 ms (Option
Halsey Taylor Owners Manual 4410 Freeze Resistant Tubular Fountain STOP!
Halsey Taylor Owners Manual 4410 Freeze Resistant Tubular Fountain STOP! PLEASE READ THE FOLLOWING INFORMATION. ITALLATION ITRUCTIO FOR THE 4410FR FTN. WITH 97243C SINGLE VALVE CONTROL ASSEMBLY ARE LOCATED
Ultrasonic Wind Sensor
CV7-L Ultrasonic Wind Sensor Page 1 of 8 1. Installation Prepare the mast head for the mechanical installation. Use the template for the bracket s screwing. Align the bracket in order to have the CV7-L
Inductive Linear Displacement Transducers Model IW 260 Measuring strokes: 80 mm, 170 mm, 240 mm, 360 mm
Inductive Linear Displacement Transducers Model IW 260 Measuring strokes 80, 170, 240, 360 Document no. IW 100 HE Date 1.07.201 Contactless, robust sensor system Infinite resolution, no hysteresis Calibrated
PURA. Pure Gas Dewpoint Transmitter. Users Guide
PURA Pure Gas Dewpoint Transmitter Users Guide Issue January 2003 Page 2 Table of Contents SECTION PAGE 1 Product Overview 3 2 Preparation 3 3 Installation 3 3.1 PURA Premium & OEM Dewpoint Transmitter
Mass Flow Controller (MFC) for Gases
Mass Flow Controller (MFC) for Gases Bypass MFC with capillary technology for nominal flow rates from 5 ml N /min to 15 l N /min Applicable for aggressive gases Compact design and digital communication
TECHNICAL DATA. Trimpac 251a. Spetember 16, 2013
Spetember 16, 2013 Trimpac 251a 1. DEsCrIpTION DESCRIPTION TRIMPAC Model B-6 and B-6B is a factory assembled trim package for a double interlocked preaction system with an electric/pneu-lectric release
Additel 761 Automated Pressure Calibrators
Automated Calibrators UPDATED Fully automated pressure calibrator with built-in pressure generator / controller to as high as 600 psi (40 bar) or as low as 0.01 Pa (0.00004 inh 2 O) accuracy Dual pressure
Operation manual Level sensor DC-LS-50 Operation Manual Level Sensor DC-LS-50
Operation Manual Level Sensor DC-LS-50 Rev.02 (2014.06) OL Page 1 of 8 Table of contents I. STRUCTURE OF THE MANUAL / CLARIFICATION... 3 II. SAFETY AND HEALTH CONCERNS... 4 1 INTRODUCTION... 5 1.1 Use
Climatic Independent Level Sensor LAR
3 JAHRE GEWÄHRLEISTUNG SENSORS FOR FOOD AND BIOPHARMA. Product Information LAR-361 LAR-761 FOOD Climatic Independent Level Sensor LAR Application / Specified usage Hydrostatic level measurement in humid
Liquid level instruments BM 24 /BM 51
KROHNE 09/2001 7.02362.21.00 GR/PRINTO Liquid level instruments / Status: 10/99 Variable area flowmeters Vortex flowmeters Flow controllers Electromagnetic flowmeters Ultrasonic flowmeters Mass flowmeters
The Discussion of this exercise covers the following points:
Exercise 5-3 Wet Reference Leg EXERCISE OBJECTIVE Learn to measure the level in a vessel using a wet reference leg. DISCUSSION OUTLINE The Discussion of this exercise covers the following points: Measuring
3.0 Pressure Transmitter Selection
3.0 Pressure Transmitter Selection Each Tronic Line pressure transmitter has different features to meet specific performance, environmental, and price requirements. It is not possible to describe every
Prewired position switches FA series
2 Prewired position switches FA series Selection diagram 01 08 10 11 1 15 1 02 external rubber gasket external rubber gasket 1 51 52 54 55 56 5 ACTUATORS adjustable lever safety adjustable lever 41 45
Float Operated Level Controllers
CONTENTS Float Operated Level Controllers IM0015 Nov. 2014 PAGE Introduction 1 Scope 1 Description 1 Specification 1 Control Installation 2 INTRODUCTION Side Mount Back Mount Prior to installing, the instructions
Installation, Operation, & Maintenance Manual. MODEL: Watlow Controller P53 Direct, P53 Remote
Installation, Operation, & Maintenance Manual Mustang Sample Conditioning System MODEL: Watlow Controller P53 Direct, P53 Remote Conforms to UL STDS 61010-1 & 1203 Certified to CSA STD C22.2 Nos. 61010-1
For ELECTRIC ANCHOR WINCH Models: T Pontoon 35 T sw Salt Water Series Coastal 35
INSTALLATION AND OPERATING INSTRUCTIONS ANCHOR WINCHES For ELECTRIC ANCHOR WINCH Models: T10109-35 Pontoon 35 T10102-35sw Salt Water Series Coastal 35 If you have any questions or difficulty installing
How to specify a product. Process Sensors and Mechanical Instruments
How to specify a product Process Sensors and Mechanical Instruments Keep the overview. Here is some guideline information on how to specify our products. Intended as supplementary help to specification
1 Overview. Pressure Measurement Single-range transmitters for general applications. 1/16 Siemens FI US Edition
Siemens AG 206 Overview Design Device structure without explosion protection The pressure transmitter consists of a piezoresistive measuring cell with a diaphragm installed in a stainless steel enclosure.
User Manual GRI- 1500Li
User Manual GRI- 1500Li Your Cart Tek caddy cart was thoroughly quality control checked and road tested before being shipped to your address. We do everything possible to assure that your caddy is in perfect
Valve Proving System VDK 200 A S02
Valve Proving System VDK 200 A S02 Valve proving system with the following approvals. UL Recognized File # MH17004 CSA Certified File # 1637485 CSA Requirement No. 4-01 (USA) Technical Information Letter
SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding