TYPE 28 DRY-RUNNING, NON-CONTACTING GAS SEALS Technical Specification
|
|
- Jonah Robbins
- 6 years ago
- Views:
Transcription
1 Standard Unidirectional Groove Design Optional Bidirectional Groove Design Product Description Type 28 compressor dry-running gas seals have been the industry standard since the 197s for gas-handling turbomachinery. Utilizing John Crane's patented spiral groove pattern, these seals are non-contacting in operation. During dynamic operation, the mating ring/seat and primary ring/face maintain a sealing gap of approximately.2 in./5 microns, thereby eliminating wear These seals eliminate seal oil contamination and reduce maintenance costs and downtime Single, double opposed, and tandem cartridge seals are capable of handling a wide variety of gas sealing applications in the gas collection/transmission, refining, chemical and petrochemical processing industries Design Features Shrouded mating ring prevents secondary damage in the event of a mating ring fracture Low-level leakage can be vented to a safe area, used as fuel to drive equipment, or returned to process via a low-pressure ejector Performance Capabilities Temperature: -22 F to 6 F/-14 C to 315 C Pressure: Speed: Shaft: Up to 6,5 psi(g)/45 bar(g) across single stage Up to 66 fps/2 m/s Up to 13.75"/35mm
2 Type 28AT Tandem Arrangement
3 Type 28XP Tandem Arrangement
4 Type 28XP-S Tandem Arrangement
5 Type 28EXP Tandem Arrangement Inlet for Filtered Seal (or Process) Gas SEAL (OR PROCESS) GAS Seal (Or Process) Gas Labyrinth Outlet for 1st Stage Leakage and Buffer Gas Interstage Labyrinth Inlet for Buffer Gas (Optional) Outlet for 2nd Stage Leakage and Separation Gas Separation Gas Supply Advanced Polymer Secondary Seal BEARING CAVITY Separation Seal - contact John Crane for options 1ST STAGE 2ND STAGE MATING RING PRIMARY RING MATING RING PRIMARY RING *Typical Application pressures up to 3,25 psi(g)/22 bar(g)
6 Typical Single Seal Arrangement and Seal Support System JOHN CRANE GAS SEALS *Single Seal Arrangement for applications not requiring a safety back-up seal. Typical Double Opposed Seal Arrangement and Seal Support System EXTERNAL SUPPLY *Double Seal Arrangement where hazardous gas is not permissible to leak into atmosphere. JOHN CRANE GAS SEALS Typical Tandem Seal Arrangement and Seal Support System APPROVED APPROVED *Tandem Seal Arrangement for applications requiring a safety back-up seal. JOHN CRANE GAS SEALS
7 Size and Speed Effect on Leakage Conditions: Air, 1,2 psig/83 bar g Leakage (SCFM) RPM 5 RPM 1 RPM Leakage (sl/min) (inch) (mm) Seal Size Pressure, Temperature and Gas Effect on Leakage Conditions: inch Diameter Seal, 14, rpm Leakage (SCFM) Leakage (sl/min) Hydrogen, 1 F/38 C Methane, 1 F/38 C Air, 1 F/38 C Air, 3 F/15 C , 1, Pressure (psig) (bar g) Gas Seal Power Consumption Conditions: Air, 14 F/6 C Power (KW) Power (HP) 1 rpm; 1. psig/69 bar g 1 rpm; 1 psig/7 bar g 5 rpm; 1 psig/7 bar g (inch) (mm) Seal Size *This information should not be used for specification purposes. Contact DryGasSeals@johncrane.com for more information about exact application requirements.
8 North America United States of America Europe United Kingdom Latin America Brazil Middle East & Africa United Arab Emirates Asia Pacific Singapore Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: Tel: Fax: If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to their selection and use. In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without prior notice. It is dangerous to smoke while handling products made from PTFE. Old and new PTFE products must not be incinerated. ISO 91 and ISO141 Certified, details available on request. 215 John Crane Revised 1/15 TD-28AT/28XP/28XPS/28EXP
TYPE 2800E EXTERNALLY MOUNTED, GAS LUBRICATED, NON-CONTACTING, DOUBLE CARTRIDGE SEAL
A Seat/Mating Ring B Face/Primary Ring (inboard) C Spring D Face/Primary Ring (outboard) E O-Ring F Drive Collar G Setting Ring H Sleeve TYPE 2800E B A D C H E Spiral Groove Technology G F Product Description
More informationTYPE 7800 SERIES 7848D/7848W UNIVERSAL VESSEL SEAL Technical Specification
A Face/Primary Ring B Seat/Mating Ring C O-ring D Disc E Sleeve F Retaining Sleeve D C E C F A B Product Description The Universal Vessel Seal 7800 Series is a modular cartridge seal for use in a wide
More informationTYPE 7828G/7828GD 7800 SERIES UNIVERSAL VESSEL SEAL Technical Specification
A Face/Primary Ring B Seat/Mating Ring C O-Ring D Disc E Sleeve F Retaining Sleeve G Retaining Clip G D C E F C A B Patent numbers: 5,938,206 and 6,142,478 Product Description The universal vessel seal
More informationTYPE 3710 CARTRIDGE SPLIT SEAL Technical Specification
A Mating Ring B Mating Ring/ Retaining Ring C Mating Ring/ Clamp Ring D Mating Ring Adapter E Primary Ring F Primary Ring/ Retaining Ring G Finger Springs H Spring Retainer I Gland O-ring J Flat Gasket
More informationTYPE ECS SEAL METAL BELLOWS DRY-RUNNING SECONDARY CONTAINMENT Technical Specification
Low Temperature Design A Spacer Ring B Compression Ring C Retaining Ring D Wave Spring E O-ring F ent/drain Connection G Seat/Mating Ring H Insert I Bellows Assembly J Housing A K Spacer B F G H I C D
More informationKAYDON RING & SEAL, INC.
KAYDON RING & SEAL, INC. K-DGS Series Dry Gas Seals KAYDON K-DGS Dry Gas Seals K-DGS Configurations Single Seal (K-DGS) Compact and economical, the single seal configuration is recommended for non-toxic
More informationCompressor Seal Replacement and Upgrades SERVICES
Compressor Seal Replacement and Upgrades SERVICES Compressor Seal Upgrades An Elliott Group compressor seal upgrade increases seal reliability and reduces process gas leakage to improve overall efficiency.
More informationApplication of Double Vs Tandem Dry gas seal Advantages.
Application of Double Vs Tandem Dry gas seal Advantages. John Sears WW Director, Compressor Products. Flowserve Corporation. Unit #2207, 220 Fisher Street, SE, Calgary, Alberta, T2H 2H8 Canada; World Wide
More informationLiquid Ring Compressors Engineered-to-Order Compressor Systems
Liquid Ring Compressors Engineered-to-Order Compressor Systems NASH Liquid Ring Compressors Greatest Performance Range of Liquid Ring Compressors Worldwide The ability to compress wet, saturated or dirty
More informationWET SEAL TO DRY GAS SEAL CONVERSION Considering the benefits of retrofitting your compressor
WET SEAL TO DRY GAS SEAL CONVERSION Considering the benefits of retrofitting your compressor Athal Doorenbos Components Focus Factory Dresser-Rand S.A. 31, Boulevard Winston Churchill 76080 Le Havre, France.
More informationImprove Reliability of Turbomachinery Lubrication and Sealing Systems
Improve Reliability of Turbomachinery Lubrication and Sealing Systems Fisher Pressure Control Solutions For Turbomachinery Applications Protect the integrity of your Turbomachinery support system Turbomachinery
More informationMechanical Seal Piping Plans
Mechanical Seal Piping Plans Companion Booklet Single Seals Dual Seals Quench Seals Second. Cont. Dual Gas Introduction A primary factor in achieving highly reliable, effective sealing performance is to
More informationSuccessful Implementation of Dry Gas Seal in High Pressure Recycle gas Compressor at Hydrocracker & Effect of Gas composition on DGS Performance
Successful Implementation of Dry Gas Seal in High Pressure Recycle gas Compressor at Hydrocracker & Effect of Gas composition on DGS Performance Why - Dry Gas Seal??? M&I shutdown and Catalyst replacement
More informationJohn Crane Type 609HTC/ECS (High-Temperature Corrosion Resistant) Sealol Metal Bellows Seal Installation Instructions
I-609HTC/ECS John Crane Type 609HTC/ECS (High-Temperature Corrosion Resistant) Sealol Metal ellows Seal Installation Instructions Foreword These instructions are provided to familiarize the user with the
More informationLiquid Ring Compressors Engineered-to-Order Compressor Systems
Liquid Ring Compressors Engineered-to-Order Compressor Systems NASH Liquid Ring Compressor Systems Engineered-to-Order Liquid Ring Compressor Systems Unmatched experience Nash liquid ring compressors are
More informationLiquid Ring Compressors Engineered-to-Order Compressor Systems
Liquid Ring Compressors Engineered-to-Order Compressor Systems NASH Liquid Ring Compressors Greatest Performance Range of Liquid Ring Compressors Worldwide The ability to compress wet, saturated or dirty
More informationDesign Enhancements on Dry Gas Seals for Screw Compressor Applications
VDI-Berichte Nr. 1932, 2006 B 8 331 Design Enhancements on Dry Gas Seals for Screw Compressor Applications Dipl.-Ing C. Kirchner, Flowserve Dortmund GmbH & Co KG, Dortmund Introduction The development
More informationSEPARATION SEAL UPGRADE TO OVERCOME REPETITIVE FAILURES
SEPARATION SEAL UPGRADE TO OVERCOME REPETITIVE FAILURES Author : Rasgas Pradip B Sonavane (Senior Engineer - Rotating Equipment) AbdelKhalek, Mohamed H (Advisor - Rotating Equipment) Quraisy Shatri (Head
More informationCompressor Systems for Offshore Oil & Gas Production
Compressor Systems for Offshore Oil & Gas Production NASH Liquid Ring Compressors Proven Technology Built From Experience For over 50 years, Gardner Denver Nash has been providing the most reliable compressors
More informationБерг АБ Тел. (495) , факс (495) Turning Ideas Into Engineered Solutions KAYDON RING & SEAL, INC.
Turning Ideas Into Engineered Solutions RING & SEAL, INC. K-CBS Series Circumferential Barrier Seals Kaydon s high performance circumferential barrier seals back up DGS systems with performance & economy.
More information61 Series Pilots for Pilot-Operated Pressure Reducing Regulators
61 Series Pilots for Pilot-Operated Pressure Reducing Regulators June 2011 Introduction 61 Series pilots are used with Types 1098-EGR and EZL pressure reducing regulators. These pilots can also be integrally
More informationExplosions in Gas Turbine Lube Oil Reservoir Result in Installation of Dry Gas Seal System
ES THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS 345 E. 47 St., New York, N.Y. 10017 The Society shall not be responsible for statements or opinions advanced in papers or in discussion at meetings of the
More informationDesign. Pompetravaini-NSB API SB Liquid Ring Compressor for Gas Processing. Working Principle
SB Pompetravaini-NSB API SB Liquid Ring Compressor for Gas Processing A family of API liquid ring compressors has been developed and has been in the market for nearly a decade, they are specifically made
More informationGAS SEAL CONTAMINATION
Proceedings of the First Middle East Turbomachinery Symposium February 13-16, 2011, Doha, Qatar GAS SEAL CONTAMINATION Raphael Bridon Components Focus Factory Manager Dresser-Rand Le Havre, France rbridon@dresser-rand.com
More informationDry Gas Seal Rack CH-3185 Schmitten Tel Mail:
Dry Gas Seal Rack CH-3185 Schmitten Tel. +41 26 497 55 66 Mail: info@felcon.ch Usually, compressor modifications are carried out because of adaptations to new operating parameters. However, in cases of
More informationPremature Dry Gas Seal Failure on a Sales Gas Centrifugal Compressor. Sergio Vidal (Saudi Aramco, Hawiyah Gas Plant - Reliability Unit)
Premature Dry Gas Seal Failure on a Sales Gas Centrifugal Compressor Sergio Vidal (Saudi Aramco, Hawiyah Gas Plant - Reliability Unit) 1 Index Copyright Saudi Aramco (YEAR). All rights reserved. No portion
More informationwww.ompressedairsystems.com ultra-high purity nitrogen generators nitrogen purity: 95% to 99.999% www.ompressedairsystems.com ultra-high purity nitrogen generators nitrogen purity: 95% to 99.999% Leading
More informationInstallation Instructions
Installation Instructions BW Seals Uniseal Series Cartridge metal bellows single and dual seals Experience In Motion Description The Uniseal metal bellows seal series consists of: Uniseal I - Single seals
More information1805 Series Relief Valves
October 2011 1805 Series Relief Valves P1026 1805G Type 1805-2 Type 1805-4 Figure 1. Typical 1805 Relief Valves Introduction The 1805 Series relief valves are designed for use in farm tap applications
More informationType 310A-32A Pressure Reducing Regulator and Type 310A-32A-32A Working Monitor Regulator
January 2009 Type 310A-32A Pressure Reducing Regulator and Type 310A-32A-32A Working Monitor Regulator Introduction The Type 310A pilot-operated high-pressure regulator (Figure 1) is used where high capacity
More informationINSTALLATION, OPERATION, AND MAINTENANCE MANUAL WELKER FILTER DRYER
INSTALLATION, OPERATION, AND MAINTENANCE MANUAL WELKER FILTER DRYER MODEL F-4 DRAWING NUMBERS AD042C[ ] AD054C[ ] MANUAL NUMBER IOM-046 REVISION Rev. F, 4/23/2018 TABLE OF CONTENTS SAFETY 3 1. PRODUCT
More informationType 1367 High-Pressure Instrument Supply System with Overpressure Protection
Instruction Manual D100343X012 Type 1367 November 2017 Type 1367 High-Pressure Instrument Supply System with Overpressure Protection TYPE 252 FILTER 2ND-STAGE TYPE 67CF FILTER-STYLE REGULATOR INLET TYPE
More informationY692VB Series Vacuum Breaker
Y692VB Series Vacuum Breaker Bulletin 71.3:Y692VB June 2009 W7429 Figure 1. Type Y692VB Vacuum Breaker Introduction The Y692VB Series direct-operated vacuum breakers are used for the precise control of
More informationshutoff valves 900 Series psig Manual Shutoff Valves
0 6000 psig Manual Shutoff Valves Features Zero leakage Protected o-ring Full flow passages Freedom from wire drawing Panel mount standard Hand wheel or toggle handle How it Works Closed O-ring seal on
More informationInstallation Instructions
Installation Instructions Durametallic MD-200 Series Gas Dual Cartridge Canister Seal for Mixers and Agitators Experience In Motion 1 Equipment Check 1.1 Follow plant safety regulations prior to equipment
More informationCP200 Series Commercial / Industrial Pressure- Loaded Pressure Reducing Regulator
CP200 Series Commercial / Industrial Pressure- Loaded Pressure Reducing Regulator May 2010 Figure 1. CP200 Series Pressure Loaded Regulator Features and Benefits Wide Range of NPT Body Sizes Easy to Install
More informationInstallation Instructions
Durametallic SL-5000 and SL-5200 Seals Cartridge Slurry Seals Installation Instructions Experience In Motion SL-5000 and SL-5200 Cartridge Seals are complete preset seal assemblies which include the sleeve
More informationType ACE95jr Tank Blanketing Valve
Type ACE95jr Tank Blanketing Valve Features Fully Balanced Plug Design Reduces Inlet Pressure Sensitivity Bulletin 74.1:ACE95JR May 2010 Stainless Steel Construction Available High Sensitivity Self-Contained
More informationThe Original 24/7 PMO Valve and 24/7 PMO Tank Valve. The only way to non-stop production. GEA Mechanical Equipment / GEA Tuchenhagen
Liquids to Value The Original 24/7 PMO Valve and 24/7 PMO Tank Valve The only way to non-stop production. GEA Mechanical Equipment / GEA Tuchenhagen No need to stop your production ever again. Control
More informationType R622 Pressure Reducing Regulator
Type R622 Pressure Reducing Regulator June 2010 Compact Design Protective Inlet Screen High Capacity Internal Relief Light Weight W8806 Inlet and Outlet Pressure Gauge Taps Figure 1. Type R622 Pressure
More informationBecker* Model FD-1500 Filter/Dryer
GE Oil & Gas Becker* Model FD-1500 Filter/Dryer Instruction Manual GE Data Classification : Public ii GE Oil & Gas 2017 General Electric Company. All rights reserved. THESE INSTRUCTIONS PROVIDE THE CUSTOMER/OPERATOR
More informationTECHNOLOGIES. M Series. Positive return metering pumps [API675]
M Series Positive return metering pumps [API675] Hydraulic double diaphragm metering pump in AISI 316L stainless steel A line of plunger and hydraulic double diaphragm metering pumps designed according
More informationTradition & Technology
Gaterotor Support Gaterotor Single Screw Compressors Design & Operation Bearing Bearings Main Screw Parallex Slide System The VSM Single Screw Compressor has one main rotor and two gaterotors. All bearings
More informationSafety Selector Valves Dual Pressure Relief Device System
ANDERSON GREENWOOD Features and enefits Provides a safe, efficient method of switching from an active pressure relief device to a standby, maintaining system overpressure protection regardless of Safety
More informationSERVICE MANUAL MODEL BA050BMST BREATHING AIR PANEL
www.modsafe.com SERVICE MANUAL MODEL BA050BMST BREATHING AIR PANEL WARNING: Do not attempt to operate this equipment without first reading and understanding the service manual enclosed with this device.
More information299H Series. Introduction. P.E.D. Categories. Specifications. Installation. Warning. Installation Guide English September 2012
Installation Guide English September 2012 299H Series Introduction This Installation Guide provides instructions for installation, startup, and adjustment of 299H Series regulators. To receive a copy of
More informationTypes 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators
Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators July 2010 W3716 W3507 Type 1808 Type 1808A Figure 1. Types 1808 and 1808A Pilot-Operated Relief Valves or Backpressure Regulators
More information1805 Series Relief Valves
Instruction Manual Form 1211 1805 Series October 2011 1805 Series Relief Valves! WARNING Failure to follow these instructions or to properly install and maintain this equipment could result in an explosion
More informationthe new Ve- / VSE Range
the new Ve- / VSE Range Pure Power, perfect price 30-680 l/min 5 / 330 / 0 bar FULFILLS THE REQUIREMENT FOR LARGE QUANTITIES OF BREATHING AIR open or Super silent EASY OPERATION Breathing air acc. to DIN
More informationTypes 627W and 627WH Direct-Operated Pressure Reducing Liquid Regulators
Types 627W and 627WH Direct-Operated Pressure Reducing Liquid Regulators Introduction The Types 627W and 627WH are direct-operated pressure reducing regulators for liquid service. They are available in
More informationS0300-BV-CAT-020 AIR COMPRESSOR SYSTEM, SUB SALV, 1150-CFM, 500-PSI. System - DS0130. System DS0130 7/8/2018 2:56:57 AM
System DS0130 Page 1 The Submarine Salvage Air Compressor System DS0130 is a portable unit used to provide high-pressure compressed air to dewater sunken vessels in up to 1000 feet of seawater. The system
More informationBrief history in the Biogas sector. Compressor features. Applications. Product range. Experience
March 2018 Brief history in the Biogas sector Compressor features Applications Product range Experience 2005 FORNOVO GAS supplied the first compressor in a biogas plant in Iceland to compress biomethane
More informationOPERATOR S MANUAL FOR AirVANTAGE 10,000 OPM 3 x 4 in. (75 x 110 mm) ORBITAL SANDERS
OPERATOR S MANUAL FOR AirVANTAGE 10,000 OPM 3 x 4 in. (75 x 110 mm) ORBITAL SANDERS Declaration of conformity AirVANTAGE Tools 10018 Lower Azusa Road, Unit #C; El Monte, California 91731 USA declare on
More informationDevelopment of a High Pressure, Oil Free, Rolling Piston Compressor
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 1994 Development of a High Pressure, Oil Free, Rolling Piston Compressor S. J. Delmotte
More informationTypes ACE95 and ACE95Sr Tank Blanketing Valves
Types ACE95 and ACE95Sr Tank Blanketing Valves Bulletin 74.1:ACE95 May 2010 W9133 W8155 Figure 1. Type ACE95 Tank Blanketing Valve Figure 2. Type ACE95Sr Tank Blanketing Valve Features Fully Balanced Pilot
More informationRod DISOGRIN Asymmetrical U-Cup Rod series U-cup with an asymmetrical profile of the sealing lips,
Industrial Seal Inc. offers a wide range of hydraulic and pneumatic rod seal profiles to meet the broad demands of the fluid power industry. These rod seals are offered in a variety of compounds and lip
More informationFILTER BYPASS CONTROL
Differential Control Valve Series 110 The Series 110 Differential Control Valve is designed to accurately control the pressure difference between any two points. In some systems this means the valve remains
More informationRate of Flow Valve Series 120
SPECIFICATIONS Rate of Flow Valve Series DIMENSIONS The OCV Series 120 Rate of Flow control valve is designed to control or limit flow to a predetermined rate, regardless offl uctuations in downstream
More informationInstallation Instructions
Installation Instructions High Temperature Metal Bellows Seals Cartridge seals with flexible graphite gaskets BXH, BXHH, BXRH, BRC, GTSP, GSDH Series 1 Equipment Check 1.1 Follow plant safety regulations
More informationCNG FILLING STATIONS
CNG FILLING STATIONS GAS INLET 3/4 F EXIT CNG TO CAR TANK 5 mt / 16 feet HOSE AND FILLING NOZZLE REMOTE ELECTRIC PANEL THREE-PHASE height 40 cm / 15.7 width 30 cm / 11.8 depth 20 cm / 7.8 EQUIPPED WITH
More informationSTANDARD HIGH PRESSURE COMPRESSORS COMPACT PACKAGE FOR DEMANDING APPLICATIONS
STANDARD HIGH PRESSURE COMPRESSORS COMPACT PACKAGE FOR DEMANDING APPLICATIONS 2 STANDARD HIGH PRESSURE COMPRESSORS BURCKHARDT COMPRESSION GLOBAL TECHNOLOGY LEADER IN THE RECIPROCATING COMPRESSOR WORLD
More informationExamination of Methods of Dry Gas Seal Supply, Regulation, and Monitoring. John Crane
Examination of Methods of Dry Gas Seal Supply, Regulation, and Monitoring Vladimir Bakalchuk GM, Technical Sales Flowserve Chicago, Il, USA Kevin Dwyer Dry Gas Seal Systems Engineer John Crane Morton Grove,
More informationGas Turbine Performance Analysis
Gas Turbine Performance Analysis Gas turbines may seem too complicated or overwhelming at first glance, but for regular field monitoring on a relative basis, it is not all that difficult. A regular check
More informationPetro-Chemical & Analyzer Sampling Systems
Petro-Chemical & Analyzer Sampling Systems Pressure control solutions for your industry. The Tescom brand offers a comprehensive range of regulators, valves and changeover systems that are ideal for analyzer
More informationTypes ACE95 and ACE95Sr Tank Blanketing Valves
August 2013 Types ACE95 and ACE95Sr Tank Blanketing Valves W9133 W8155 Figure 1. Type ACE95 Tank Blanketing Valve Figure 2. Type ACE95Sr Tank Blanketing Valve Features Fully Balanced Pilot Design Reduces
More informationSIHI LPH-X - Liquid Ring Compressors
- Liquid Ring Compressors LPH 50523 LPH 60527 Pressure range: Suction volume range: 0.2 to 1.5 bar 260 to 780 m³/h CONSTRUCTION Sterling SIHI liquid ring compressors are displacement compressors with a
More informationv. Size shall be specified on drawings.
SPECIFICATION FOR VACUUM INSULATED PIPING Part 1 General 1. Submittals a. After award of contract and before executing any manufacturing, shop drawings and specifications shall be submitted to the customer
More information1305 Series Pressure Reducing Regulators
Instruction Manual Form 1095 1305 Series October 2009 1305 Series Pressure Reducing Regulators! Warning Fisher regulators must be installed, operated, and maintained in accordance with federal, state,
More informationTurbo Blowers. Combustion Excellence Since Features. Benefits
Turbo Blowers Features Integral molded scroll design Turbine bladed impeller Steel inlet guard Precisely balanced impellers eliminate vibration Complete line of available accessories for adapting to any
More informationSRL Series. Oil-less Scroll Air Compressors. Pharmaceutical. Research & Development. Food & Beverage. Chemical. Electronic
Pharmaceutical SRL Series Oil-less Scroll Air Compressors Research & Development Food & Beverage Chemical Electronic Hitachi Industrial Equipment Product Brochure Hitachi SRL Series scroll compressors
More informationDräger CAPITANO 140 Mobile Compressor
Dräger CAPITANO 140 Mobile Compressor The true capabilities of the Dräger CAPITANO 140 mobile compressor become apparent during professional operations at sea. Filling tube with filling valve Handle Fan
More informationType 1190 Low-Pressure Gas Blanketing Regulator
April 202 Type 90 Low-Pressure Gas Blanketing Regulator W7428 Figure. Type 90 Low-Pressure Gas Blanketing Regulator Introduction The Type 90 low-pressure gas blanketing regulator is used for extremely
More informationFundamentals of Compressed Air Systems. Pre-Workshop Assignment
Page 1 In order to ensure that the Compressed Air Challenge Fundamentals of Compressed Air Systems Training is most useful to you, it will be important for you to bring information about your plant s compressed
More informationGAS INJECTION TECHNOLOGY GIT
GAS INJECTION TECHNOLOGY GIT Innovative and complete solutions ECONOMICAL modular RELIABLE BAUER KOMPRESSOREN offer Gas Injection Technology as a solution to the problems of plastic part production. The
More informationCirculation Systems for Single and Multiple Seal Arrangements
Circulation Systems for Single and Multiple Seal Arrangements Gordon Buck and Ralph Gabriel, John Crane This discussion opens a three-part series covering mechanical seal piping plans that provide guidelines
More informationHP/UHP Spring-Loaded Regulator
Description HP (High Purity) and UHP (Ultra High Purity) products are for service where the product must be kept free of contamination. The design is kept simple to minimise dead areas where contaminants
More informationInert Air (N2) Systems Manual
INSTRUCTION MANUAL Inert Air (N2) Systems Manual N2-MANUAL 2.10 READ AND UNDERSTAND THIS MANUAL PRIOR TO OPERATING OR SERVICING THIS PRODUCT. GENERAL INFORMATION Positive pressure nitrogen gas pressurizing
More informationDESIGN AND MITIGATION TECHNIQUES FOR APPLICATIONS WITH POSSIBLE LIQUID CONTAMINATION OF THE SEALING GAS DRY GAS SEAL SYSTEM
by James F. McCraw Senior Consultant, Rotating Equipment BP America, Inc. Houston, Texas Vladimir Bakalchuk Manager, Type 28 New Products and Richard Hosanna Type 28 Engineering Manager John Crane Inc.
More informationCONTAINMENT SEALS FOR API 682 SECOND EDITION
CONTAINMENT SEALS FOR API 682 SECOND EDITION by Peter E. Bowden Technical Services Manager John Crane EAA Manchester, England and Chris J. Fone Director of Technical Services John Crane EAA Slough, England
More informationTechTalk. Purging for Delayed Coking. Understanding purging system design in heavy-fouling applications. Outline
Page 1 of 6 TechTalk Understanding purging system design in heavy-fouling applications Purging for Delayed Coking Outline Introduction In high-fouling applications such as heavy oil processing and What
More informationCommercial Service Regulator Platform
Commercial Service Regulator Platform Engineered to fit a multitude of applications. Next Generation of Pressure Regulator Technology CS800 Series CSB600 and CSB700 Series CP200 and CP400 Series CS200,
More informationPressureGuard. Self-Contained Hydraulic Emergency Shutdown Systems For Rotary or Non API 6A Linear Valves
PressureGuard Self-Contained Hydraulic Emergency Shutdown Systems For Rotary or Non API 6A Linear Valves Design and Construction Emerson Process Management - Valve Automation is a recognized leader in
More informationT208VR Series Tank Blanketing Vacuum Regulator
February 2014 T208VR Series Tank Blanketing Vacuum Regulator Figure 1. Typical T208VR Series Vacuum Regulator Introduction The T208VR Series direct-operated vacuum regulators are used where a decrease
More informationLiquid ring compressors
Liquid ring compressors KPH 95652 Compression pressures: 6 to 12 bar(g) Suction volume flow: 2960 to 3600 m³/h 78 to 174 psig 1742 to 2119 cfm DESIGN TYPE SIHI liquid ring compressors are displacement
More informationMechanical Seal Piping Plans
Mechanical Seal Piping Plans Single Seals plans 01, 02, 11, 13, 14, 21, 23, 31, 32, 41 Dual Seals plans 52, 53A, 53B, 53C, 54 Quench Seals plans 62, 65 Gas Seals plans 72, 74, 75, 76 Mechanical Seal Piping
More informationDräger PAS AirPack 2 Compressed Air Breathing Apparatus
Dräger PAS AirPack 2 Compressed Air Breathing Apparatus Designed using leading technology and materials, Dräger s range of heavy-duty airline apparatus is ideal for use where an extended duration of breathing
More informationHT Series. 1500kW to 5500kW
HT Series 1500kW to 5500kW HamiltonJet HT Series. HamiltonJet HT series waterjets represent the next evolution in waterjet propulsion technology. Developed from the highly successful HamiltonJet HM waterjet
More informationTypes ACE95 and ACE95Sr Tank Blanketing Valves
October 2014 Types ACE95 and ACE95Sr Tank Blanketing Valves W9133 W8155 Figure 1. Type ACE95 Tank Blanketing Valve Figure 2. Type ACE95Sr Tank Blanketing Valve Features Fully Balanced Pilot Design Reduces
More informationTESCOM 50-4X Series Safety, Installation & Start-Up Procedures
Operations & Service Manual TESCOM 50-4X Series Safety, Installation & Start-Up Procedures Do not attempt to select, install, use or maintain this product until you have read and fully understood this
More information1301 Series High-Pressure Regulators
Instruction Manual Form 1111 Types 1301F and 1301G March 2013 1301 Series High-Pressure Regulators! WARNING Failure to follow these instructions or to properly install and maintain this equipment could
More informationPRO-50 Instrument Supply Regulator
Features CRN Approved The PRO-50 Regulator has been granted a Canadian Registration Number. Sour Service Capability Available in NACE configurations that comply with NACE MR0175/MR0103. Environmental limits
More informationTest Report # Rev 0. Adiabatic Compression In Nitrogen Service
Test Report # 30011300 Rev 0 Adiabatic Compression In Nitrogen Service Scope: This test report contains test data on the effects of adiabatic compression in nitrogen service on AP3600 diaphragm valves
More informationThe Ultimate Way To Degasify Compressor Seal Oils
THERMOJET G 3000 SERIES The Ultimate Way To Degasify Compressor Seal Oils BENEFITS FEATURES Electric Heater Type 300 Series Stainless Steel Construction Proprietary Dual-Stage Jet Mixer Particulate Filtration
More informationUSE OF NONCONTACTING SEALS IN VOLATILE SERVICES
USE OF NONCONTACTING SEALS IN VOLATILE SERVICES by Bob Goodenberger Regional Engineer, South Central Region John Crane Inc. Webster, Texas Douglas E. Barron Reliability Analyst ChevronPhillips Chemical
More informationType FEQ Slam-Shut Valve
Instruction Manual Form 5865 Type FEQ December 2012 Type FEQ Slam-Shut Valve Contents Introduction...1 Principle of Operation...1 Specifications...2 Installation...2 Commissioning...7 Adjustment...9 Shutdown...10
More informationFOR INSTALLING CO 2 BLENDER KIT (P/N IN BEER SYSTEM
IMI CORNELIUS INC One Cornelius Place Anoka, MN 55303-623 Telephone (800) 238-3600 Facsimile (612) 22-326 INSTALLATION INSTRUCTIONS FOR INSTALLING CO 2 BLENDER KIT (P/N 111612000 IN BEER SYSTEM SECONDARY
More informationInstallation Operation Maintenance
682 Seal Cooler New generation seal cooler to meet and exceed the seal cooler requirements stated in the 4th Edition of API Standard 682 Installation Operation Maintenance Experience In Motion Description
More information2 Sentry MCL Installation, Operation & Maintenance
Gas Liquid & Slurry Solid & Powder Steam & Water Installation, Operation & Maintenance Manual Original Instructions Liquid Sampling Manual Low-Emission Samplers S-GA-IOM-00249-7 11-17 Sentry MCL 966 Blue
More informationBalston Nitrogen Generation Systems
Lower cost...eliminates the need for costly gas cylinders Complete package with prefilters, final filters, and receiving tank Compact - frees up valuable floor space Eliminates unexpected shutdowns due
More informationHigh-Purity. Ball Valves
High-Purity s Components MANUFACTURING ASSEMBLY TESTING HP High-Purity s CFOS Applications Cost-effective systems where cleaning for oxygen-grade services are required, such as: Clean-Dry Air (CDA), Oil-Free
More information