Hands-On Experiment Density and Measurement
|
|
|
- Augustine Anthony
- 5 years ago
- Views:
Transcription
1 Hands-On Experiment Density and Measurement GOALS: 1. To measure liquid volume as accurately as possible with graduated cylinders. 2. To measure the volume of irregular shaped solid objects by liquid volume displacement. 3. To measure liquid volumes by pipetting into containers. 4. To weigh objects as accurately as possible on a Top Loader Balance. 5. To weigh objects to six significant figures on an analytical balances. 6. To calculate the density of known and unknown solids and liquids by measuring the mass and the volume of the objects with lab instruments. 7. To observe experimental deviations through error of instruments or students. 8. To introduce the terms accuracy, precision, reliability, sensitivity as related to an analytical procedure. EQUIPMENT: 10 ml Graduated cylinder 100 ml Graduated cylinder 10 and 25 ml Volumetric pipette 25 to 50 ml Erlenmeyer Flask with solid rubber stopper 110 C Thermometer CHEMICALS OR UNKNOWNS: One solid rubber stopper ( either a #2, #1, or #0 as long as it freely fits into the 100 ml graduated cylinder) Unknown solid: Metal slugs in box at the front desk or box of pennies Distilled water Unknown liquid: Acetone, Alcohol, other organic Liquid
2 INSTRUMENT: Top Loading Balance (0.01g) Top Loading Balance (0.001g) PROCEDURES: (1) The student should read the experiment before attending lab. (2) The student should copy the sample data page into her/his lab notebook. (3) Turn in your Measurement experiment s Post Lab Report and Data Page copies from your lab notebook PART A: DENSITY OF A KNOWN SOLID (1) The students will calculate the density of rubber by measuring the mass and the volume of the rubber stopper. The rubber stopper must be small enough so that it will not jam in the graduated cylinder. The students should use a 100 ml graduated cylinder. (2) The 100 ml graduated cylinder should have division marking for each milliliter so that the student may measure the volume estimated to the nearest 3/10 or 2/10 of a milliliter. Remember to always read a graduated cylinder with your line of sight directly perpendicular to the BOTTOM of the meniscus. On a white piece of paper, make a heavy dark line at least ¼ in thick. Place the paper, behind the graduate. Slide the paper up until the top of the dark line is about one division below the meniscus. This technique will make the meniscus more prominent and easier to read, allowing you to estimate between the lines for one more significant figure. (3) Your graduated cylinder must be clean. Clean glassware will be free of water droplets clinging above the meniscus. (water film is okay) Place 15 ml or more water in the graduate. Read the volume accurately and record in your lab notebook. Your reading should estimate one decimal place.
3 (4) The student will next weigh the rubber stopper directly on the Top Loading Balance on your lab island. The mass should be recorded to the nearest 0.01 gram. Record the mass in your lab notebook. (5) Then the student will carefully slide the stopper into a graduate by tipping the graduate to a 45 angle. The student should not splash one drop. Tap the graduate to free any trapped air bubbles. If any water droplets are clinging above the meniscus, you will have to wash the graduate with soap and water and begin again. (6) The student will record the new volume in the lab notebook. Calculate the volume of the stopper, by subtracting the reading #3 from the reading #6. This is known as a volume of a solid by liquid replacement. (7) Using a calculator, divide the mass of the stopper by its volume to determine the density. DENSITY is MASS PER UNIT VOLUME. Therefore by dividing the mass of the rubber stopper by its volume, the density may be calculated. Since the mass should be at least two figures accurate and the volume at least two figure accurate the density should be calculated to three significant figures, the rounded off to two significant figures answer. The correct answer is 1.24g/ ml for the black stoppers and 1.44 g/ ml for the green stoppers. Rounded off, that would be 1.2 and 1.4 PART B: DENSITY OF AN UNKNOWN SOLID (1) Calculate the density of an unknown solid assigned to you by your instructor. Use the procedures similar to PART A, with the following modifications: (metal slugs in the box on the front desk or 25 Post 1982 pennies, or pellets) (2) Use a 10 ml/ 25 ml/ or 50 ml graduate that has division marking at least 2/10 of a ml or preferably 1/10 of a ml(10 ml graduate), that the object(s) will fit inside. (3) Weigh the metal slugs or pennies. Record in your lab notebook.
4 (4) Measure approximately 5 ml of water in the 10 ml graduate or 10 ml in 25 ml graduate and read the volume level to the nearest 2/10 or 2/10 of a ml. Some of our graduates will come close to the nearest 3/10 ml. (5) Tilt the graduate and carefully slide the unknown into graduated cylinder, so as not to splash out any water. Make sure the unknown is completely submerged and the water below the 10 ml line/or top line. Record the volume. (6) Calculate the volume of the solid. (7) Calculate the density of the solid to the nearest 1 /10 of a gram by rounding off the answer. (8) Using a paper towel from the wash sink, drain off the water from the graduate, pour the unknown on the towel (careful not to spill). Fold the towel and blot until dry. Put the dried unknown back on the cart or front desk. PART C: DENSITY OF A KNOWN LIQUID (1) With a pipette, small flask, and a Top Load Balance (0.001g) student will calculate the density of water to three significant figures. (2) Weigh you 50 ml stoppered dried flask. (3) Using your 100 ml graduate, obtain about 40 or 50 ml of deionized water. (squeeze bottle or from carboy at wash-up sink) (4) After you have made your first weighing, pipette 25 ml of deionized water in your weighed flask. At the fill mark on the pipet (line above the bubble) exactly 25.0 ml water can be measured with a SENSITIVTY of _+ 2/100 of an ml.
5 (5) ml has been listed in your lab notebook. (6) Weigh the flask and contents on the same Top Loading Balance you used before. Refer to your procedures or (7) Calculate the mass of the water. (subtract empty flask from the flask plus water) (8) Calculate the density of water to three decimal places. (9) Record the temperature of the water by using a 110 C Thermometer. Use the table on the next page for the correct density. TABLE FOR DENSITY OF WATER TEMPERATURE C DENSITY g/ml TEMPERATURE C DENSITY g/ml
6 PART D: DENSITY OF UNKNOWN LIQUID (1) Using the Top Load Balance, (0.001 g) and a 10 ml pipet, dry flask, calculate the density of an unknown liquid. Use the same procedures as you followed in PART C, but add these modifications. (2) Using a clean dried 25 ml stoppered flask, weigh on the Top Loading Balance (0.001 g). (3) Obtain an unknown from the front desk (Acetone, Ethyl alcohol (ethanol), or methyl alcohol (methanol) in a small beaker. Pipette, using a ml volumetric pipette, ml into the weighed flask stopper. (4) Weigh the stoppered flask on the Top Loader Balance (0.001 g). (5) Calculate the density of the unknown. Have your data page in your lab notebook initialed by the instructor before leaving the lab.
Lab #1: Introduction to Lab Techniques INTRODUCTION
Name Lab #1: Introduction to Lab Techniques INTRODUCTION Our goals in this experiment are (1) to make some measurements using a metric ruler, (2) to learn how to determine volumes with a graduated cylinder,
Measuring Mass and Volume
Measuring Mass and Volume Experiment 2 Expt 2 Measurement.wpd INTENT The purpose of this experiment is to introduce some fundamental aspects of the measurement making process as well as to introduce some
Read ENTIRE lab up to Disposal Section. MAKE NOTES!!! **For Procedures, Highlight equipment used and circle quantities measured out.
Lab Ch 2 Mass, Volume, & Density Lab Partners: READ Prelab!!! Read ENTIRE lab up to Disposal Section. MAKE NOTES!!! **For Procedures, Highlight equipment used and circle quantities measured out. Density
CHM 100 / Introductory Laboratory Experiment (r10) 1/11
CHM 100 / 110 - Introductory Laboratory Experiment (r10) 1/11 Purpose This introductory exercise will familiarize you with a few of the measurements we make in the chemistry laboratory and the level of
Purpose. Introduction
Purpose The objective of this experiment is to determine the density of an unknown liquid and solid. The students will become familiar with the techniques for measuring mass and volume of several samples
VOLUMETRIC TECHNIQUES
REVISED 10/14 CHEMISTRY 1101L VOLUMETRIC TECHNIQUES Volume measurements are important in many experimental procedures. Sometimes volume measurements must be exact; other times they can be approximate.
Lab 1: Precision and Accuracy in Measurement (Using the right tool for the Job) and Density of Metals
Lab 1: Precision and Accuracy in Measurement (Using the right tool for the Job) and Density of Metals Objectives: - To understand the meaning of accuracy and precision You will determine the relative precision
CHM Introductory Laboratory Experiment (r17sd) 1/13
CHM 110 - Introductory Laboratory Experiment (r17sd) 1/13 Purpose This introductory exercise will familiarize you with a few of the measurements we make in the chemistry laboratory and the level of uncertainty
The use of the analytical balance, and the buret.
1211L Experiment 1. Density 2015 by H. Patterson Instructor Notes: Students make measurements individually then share data to make the graph. There are four volumetric measurements to be studied; 3.00
CH2250: Techniques in Laboratory Chemistry. Outline Measuring Mass Measuring Volume Significant figures. Mass Measurement
CH2250: Techniques in Laboratory Chemistry Outline Measuring Mass Measuring Volume Significant figures Mass Measurement Mass Measurement Measure mass not weight Mass is measured with a balance (a scale
CHEM 321 Experiment 1
CHEM 321 Experiment 1 Basics Review and Calibration of Volumetric Glassware There are three types of containers used in lab to contain or deliver liquids: volumetric, ordinary and disposable glassware.
Experiment #2. Density and Measurements
Experiment #2. Density and Measurements Goals 1. To measure and record length, volume and mass accurately with the correct number of significant figures 2. To use significant figures correctly in calculations.
Calibration of Volumetric Glassware
Calibration of Volumetric Glassware Introduction This set of laboratory experiments is designed to introduce you to some of the apparatus and operations you will be using during the remainder of this course,
BASIC LABORATORY TECHNIQUES (Revised )
BASIC LABORATORY TECHNIQUES (Revised 1-6-13) A. WEIGHING The determination of the quantity of matter in a sample is most directly determined by measuring its mass. The process by which we determine the
Lab Equipment ANALYTICAL BALANCE
Lab Equipment ANALYTICAL BALANCE Analytical balances are used for very accurate, quantitative measurements of mass to the nearest 0.001 g. (Some read to 0.0001 g.) These are delicate instruments, subject
Target Density Lab SCIENTIFIC. Density Inquiry Lab Activities. Introduction. Concepts. Materials. Safety Precautions. Preparation
Target Density Lab Density Inquiry Lab Activities SCIENTIFIC Introduction The concept of density is reinforced as students measure the volume and mass of an unknown liquid in a graduated cylinder, graph
Recording Significant Figures
Recording Significant Figures Having the correct significant figures in your lab reports begins with recording the correct significant figures from the data you obtain in lab. This packet will demonstrate
BASIC LABORATORY TECHNIQUES (Revised )
BASIC LABORATORY TECHNIQUES (Revised 1-2-16) (See Appendix II: Summary for making Spreadsheets and Graphs with Excel and Appendix III parts C, C1 and C2: Significant figures, scientific notation and rounding)
Objective To identify a pure liquid substance using the physical properties of solubility, density, and boiling point.
Chemistry 1020 Identification of an Unknown Liquid Objective To identify a pure liquid substance using the physical properties of solubility, density, and boiling point. Text reference solubility, density,
EXPERIMENT 2. Laboratory Procedures INTRODUCTION
EXPERIMENT 2 Laboratory Procedures INTRODUCTION Begin each experiment by taking the necessary safety precautions. All materials that will not be used in the lab should be placed out of the laboratory working
Experiment 1 Basic Laboratory Operations
Experiment 1 Basic Laboratory Operations INTRODUCTION LECTURE OUTLINE This is the first experiment that most students perform in the laboratory. Oftentimes, the stone is cast in this first laboratory session.
Laboratory Activity Measurement and Density. Average deviation = Sum of absolute values of all deviations Number of trials
Laboratory Activity Measurement and Density Background: Measurements of mass and volume are very common in the chemistry laboratory. The analytical balance is used to measure mass, and the graduated cylinder,
CHM250 Calibration and Measurement Lab. Balance Calibration
CHM250 Calibration and Measurement Lab Green Profile Balance Calibration Introduction: Balances that are properly operated, calibrated and maintained are crucial for laboratory operations. The accuracy
EXPERIMENT 1 TOOLS FOR LAB MEASUREMENT
EXPERIMENT 1 TOOLS FOR LAB MEASUREMENT INTRODUCTION A course in chemistry, one of the physical sciences, differs from a course in, say, literature or history. A main difference is that chemistry usually
Scientific Measurements and Errors: Determination of Density of Glass
Experiment Scientific Measurements and Errors: Determination of Density of Glass II Purposes This experiment has three purposes: 1. Making anumber of measurements, including length, weight, and liquid
1. Determining Solution Concentration
In this exercise you will determine the concentration of salt solutions by measuring samples with known concentration and making a calibration curve. You will review units of concentration, and how to
Density of Brass: Accuracy and Precision
Density of Brass: Accuracy and Precision Introduction Density is a measure of a substance s mass-to-volume ratio. For liquids and solids, density is usually expressed in units of g/ml or g/cm 3 ; these
Determination of the Gas-Law Constant (R) using CO2
Determination of the Gas-Law Constant (R) using CO2 EXPERIMENT 11 Prepared by Edward L. Brown and Miranda Raines, Lee University The student will become familiar with ideal gases and how their properties
Any laboratory is equipped with specific tools, equipment,
Use of Laboratory Equipment and Supplies 3 When you have completed this exercise, you will be able to: 1. Use a balance. 2. Use pipettes and graduated cylinders to measure the volume of liquids. 3. Use
EXPERIMENT 1 BASIC LABORATORY TECHNIQUES AND TREATMENT OF DATA MEASUREMENTS
EXPERIMENT 1 BASIC LABORATORY TECHNIQUES AND TREATMENT OF DATA MEASUREMENTS Introduction In the following experiment you will be required to use a Bunsen burner, balance, a pipet, graduated cylinder, flask,
Additional Reading General, Organic and Biological Chemistry, by Timberlake, chapter 8.
Gas Laws EXPERIMENTAL TASK Determine the mathematical relationship between the volume of a gas sample and its absolute temperature, using experimental data; and to determine the mathematical relationship
Accuracy and Precision
Accuracy and Precision Introduction Scientists use many skills as they investigate the world around them. They make observations by gathering information with their senses. Some observations are simple.
NAME BLOCK Density Lab PROBLEM: How can we determine the densities of different substances?
NAME BLOCK Density Lab PROBLEM: How can we determine the densities of different substances? PART 1 Determining relative density procedure 1. Designate an eyedropper for each beaker. Do not mix them up
Figure 1. Example of volume of water required for an unknown sample
Experiment Three Density Procedure Part 1.The density of a solid Obtain a solid unknown sample from your instructor. Write down the number of the unknown in your notebook. Determine the of your unknown
R: The Ideal Gas Constant Pre-Lab Assignment
R: The Ideal Gas Constant Pre-Lab Assignment Read the entire laboratory investigation and the relevant pages in your textbook, then answers the questions that follow in the space provided below. 1 Describe
Lab 1. Instrumentation Familiarity: Using Micropipetters and Serological Pipettes
Instrumentation Familiarity: Using Micropipetters and Serological Pipettes Introduction: In molecular biology we sometimes need to measure volumes as small as one millionth of a liter (a liter is about
MEASURING VOLUME & MASS
MEASURING VOLUME & MASS In this laboratory you will have the opportunity to apply your measuring skills in gathering data, processing it, and interpreting the results. For this experiment you will: 1)
Experiment 1 Introduction to Some Laboratory Measurements
Experiment 1 Introduction to Some Laboratory Measurements Introduction In this experiment you will familiarize yourself with the English & metric systems of measurement, weigh with a centigram balance,
Buoyancy and the Density of Liquids (approx. 2 h) (11/24/15)
Buoyancy and the Density of Liquids (approx. 2 h) (11/24/15) Introduction Which weighs more, a pound of lead or a pound of feathers? If your answer to this question is "a pound of lead", then you are confusing
QAM-I-117 Volumetric Equipment Calibration Verification
1. Applicability and Purpose This procedure applies to all adjustable and fixed volume pipetters and any labware used to deliver measured volumes of liquid by laboratory analysts at the Texas Institute
Experiment 13 Molar Mass of a Gas. Purpose. Background. PV = nrt
Experiment 13 Molar Mass of a Gas Purpose In this experiment you will use the ideal gas law to calculate the molar mass of a volatile liquid compound by measuring the mass, volume, temperature, and pressure
PRE LABORATORY ASSIGNMENT: Lab Section Score: /10 READ THE LAB TEXT BEFORE ATTEMPTING THESE PROBLEMS!
EXPERIMENT # 6 Name: PRE LABORATORY ASSIGNMENT: Lab Section Score: /10 READ THE LAB TEXT BEFORE ATTEMPTING THESE PROBLEMS! 1. Calculate the height of a corresponding column of mercury (in mm) that is at
11.1 Dumas Method - Pre-Lab Questions
11.1 Dumas Method - Pre-Lab Questions Name: Instructor: Date: Section/Group: Show all work for full credit. 1. If a 275-mL gas container has pressure of 732.6 mm Hg at -28 C, how many moles of gas are
CHM 317H1S Winter Section P Procedures and Tables
CHM 317H1S Winter 2018 Section P Procedures and Tables Procedures Page 1 Standard Operating Procedures Throughout the laboratory portion of this course, you will be required to perform a number of operations
CHM 2045L Physical Properties
CHM 2045L Physical Properties Purpose: To observe and record some common physical properties. Background: Physical properties can tell us a lot about an unknown chemical. In this experiment you will look
Experiment 12: MOLAR VOLUME OF AN IDEAL GAS
Experiment 1: MOLAR VOLUME OF AN IDEAL GAS Purpose: Determine the molar volume of a gas at standard temperature and pressure (STP, 0 C and pressure of 1 atm) Performance Goals: Collect and measure the
LABORATORY SAFETY EQUIPMENT Final Grade: /45
LABORATORY SAFETY EQUIPMENT Final Grade: /45 CH.lbSg - Identify, locate, and know how to use laboratory safety equipment including laboratory aprons, lab safety goggles, lab gloves, fire extinguishers,
CONCEPTUAL PHYSICS LAB
PURPOSE The purpose of this lab is to determine the density of an unknown solid by direct calculation and by graphing mass vs. volume for several samples of the solid. INTRODUCTION Which is heavier, a
Part A How Many Drops Are in 1 ml of Water?
Investigation: Tools and Measurements Name(s): Introduction: This investigation requires you to use various scientific tools to measure volume, mass, and dimensions of objects. The goal is to become familiar
Student s Name: Date : Molar volume of butane
Student s Name: Date : Background Molar volume of butane The purpose of this activity is to determine the molar mass of butane using gas from a butane lighter. The experiment depends on the fact that the
00 Experiment: Basic Lab Techniques, Compliance of GLP and Calibration of Glassware
00 Experiment: Basic Lab Techniques, Compliance of GLP and Calibration of Glassware OBJECTIVE: In this experiment you will learn the basic techniques when carrying out chemical analysis. You will learn
Experiment 1, Measurement and Density Chemistry 201, Wright College, Department of Physical Science and Engineering
Name Date Experiment 1, Measurement and Density Chemistry 201, Wright College, Department of Physical Science and Engineering Making measurements in the laboratory involves equipment and instrumentation.
LABORATORY TECHNIQUES. Pouring Liquids
LABORATORY TECHNIQUES Working in the chemistry laboratory you will be handling potentially dangerous substances and performing unfamiliar tasks. This section provides you with a guide to the safe laboratory
download instant at Experiment 2 A Submarine Adventure: Density Saves the Day
Experiment 2 A Submarine Adventure: Density Saves the Day Instructor Notes and Lab Preparation: Chemicals and Equipment: various metal shapes of copper, nickel, lead, aluminum, brass, iron and magnesium
Read over Techniques #2, 4, 5, 6, and 9 in the Demonstrations of Nine Practical Lab Techniques booklet.
Practical Assessment 1 includes: Technique #2 - Use of a Pipette Technique #4 Weighing Technique #5 Use of a Bottle-Top Dispenser Technique #6 Gravity Filtration Technique # 9 Rotary Evaporator Student
The Determination of the Value for Molar Volume
Name AP Chemistry The Determination of the Value for Molar Volume Objective Using a chemical reaction that produces a gas, measure the appropriate values to allow a determination of the value for molar
Check-In, Lab Safety, Balance and Volumetric Glassware Use, Introduction to Statistics, and MSDS Familiarization
Check-In, Lab Safety, Balance and Volumetric Glassware Use, Introduction to Statistics, and MSDS Familiarization Before coming to lab: Read Chapter 2 of your textbook before coming to lab. This chapter
Measurements. Metric System
Measurements Measurements are basic to any scientific pursuit. A measurement has both a magnitude (numeric value) and a unit. Metric units are used in the sciences. Metric System In science, the metric
Gas Laws. Figure 1: Experimental Set-up with Leveling Bulb. GCC CHM 151LL: Gas Laws GCC, 2019 page 1 of 8
Gas Laws Introduction Although we cannot see gases, we can observe their behavior and study their properties. This lab will apply several concepts from Ideal Gas Laws. You will use your knowledge of chemical
ASPHALT PLANT LEVEL 1
ASPHALT PLANT LEVEL 1 Module 6: Maximum Specific Gravity FM 1 T 209 FDOT Course Release: 10, Module 6 1 Specification Year: January 2015 The terms Gmm or Maximum Specific Gravity or Rice gravity are often
General Laboratory Rules Graphing Data...13
iii TABLE OF CONTENTS LAB INFORMATION General Laboratory Rules................................. 1 Common Laboratory Equipment............................ 4 Directions for the Laboratory Notebook........................
The Decomposition of Potassium Chlorate
The Decomposition of Potassium Chlorate Small quantities of molecular oxygen (O 2 ) can be obtained from the thermal decomposition of certain oxides, peroxides, and salts of oxoacids. Some examples of
Pearson Education Limited Edinburgh Gate Harlow Essex CM20 2JE England and Associated Companies throughout the world
Pearson Education Limited Edinburgh Gate Harlow Essex CM20 2JE England and Associated Companies throughout the world Visit us on the World Wide Web at: www.pearsoned.co.uk Pearson Education Limited 2014
EXPERIMENT 8 Ideal Gas Law: Molecular Weight of a Vapor
EXPERIMENT 8 Ideal Gas Law: Molecular Weight of a Vapor Purpose: In this experiment you will use the ideal gas law to calculate the molecular weight of a volatile liquid compound by measuring the mass,
Analysis of a KClO3 Mixture and Determination of R
Experiment 10 Analysis of a KClO3 Mixture and Determination of R Pre-Lab Assignment Before coming to lab: Read the lab thoroughly. Answer the pre-lab questions that appear at the end of this lab exercise.
MassWWP Standard Operating Procedure R-2 Dissolved Oxygen Rev.0 Page 1 of 10
MassWWP Standard Operating Procedure R-2 Dissolved Oxygen Rev.0 Page 1 of 10 MassWWP Standard Operating Procedure R-2 Dissolved Oxygen Rev.0 Page 2 of 10 Table of Contents Field Equipment List...3 Sampling
Laboratory #2 Pipetting Technique and Micropipette Calibration Skills=40 pts
Laboratory #2 Pipetting Technique and Micropipette Calibration Skills=40 pts Objectives: Upon completion of this unit, the student should be able to: 1. List and describe 3 categories of pipets. 2. List
I CAN: Define Volume, know that it is a property of matter, and measure volume accurately.
LastFirst Date Per # 5 4 3 2 1 0 late WORKED HARD DURING CLASS TIME even if some sections not quite done. Mostly Complete Not Accurate Instructions not followed Overall Neatness Parts left undone Complete
Lab Skills Practice: Pipetting Small Volumes. B3 Summer Science Camp at Olympic High School 2016
Lab Skills Practice: Pipetting Small Volumes B3 Summer Science Camp at Olympic High School 2016 Pipetter types Serological and micropipettes are used to accurately transfer small liquid volumes (micro-liter
Name: Period: DUE Friday 9/ 16 Honors Chemistry Lab #1: Metric System
Name: Period: DUE Friday 9/ 16 Honors Chemistry Lab #1: Metric System Introduction: The Metric System is a worldwide standard system of measurement. Scientists must be able to communicate with each other
The Ideal Gas Constant
Chem 2115 Experiment # 8 The Ideal Gas Constant OBJECTIVE: This experiment is designed to provide experience in gas handling methods and experimental insight into the relationships between pressure, volume,
1. If grams of the vapor of a volatile liquid can fill a 498 ml flask at o C and 775 mm Hg, what is the molecular mass of the gas?
MOLECULAR MASS OFA VOLATILE LIQUID A lab to study the ideal gas law Introduction The ideal gas law indicates that the observed properties of a gas sample are directly related to the number of moles of
The Determination of the Value for Molar Volume
Objective The Determination of the Value for Molar Volume Using a chemical reaction that produces a gas, measure the appropriate values to allow a determination of the value for molar volume. Brief Overview
CH 112 Special Assignment #2 Density Layers and Lava Lamps
CH 112 Special Assignment #2 Density Layers and Lava Lamps PRE-LAB ASSIGNMENT: Make sure that you read this handout and bring the essentials to lab with you. Here are the pre-lab questions for this week.
General Chemistry I Percent Yield of Hydrogen Gas From Magnesium and HCl
Introduction For chemical reactions involving gases, gas volume measurements provide a convenient means of determining stoichiometric relationships. A gaseous product is collected in a long, thin graduated
The Rules. 1. Conduct yourself in a responsible manner at all times in the laboratory.
The Rules 1. Conduct yourself in a responsible manner at all times in the laboratory. 2. Follow all written and verbal instructions carefully. If you do not understand a direction or part of a procedure,
How to Measure R7.1. Reference. I. Linear dimensions
How to Measure Written by Connie Russell I. Linear dimensions Measuring linear dimensions (the distance between two points) is usually associated with using a ruler or a tape measure. For measuring objects
Chapter Pipette service & maintenance. Pipette specifications according to ISO Repair in the lab or return for service?
Pipette specifications according to ISO 8655 Chapter 5 5.1 The ISO 8655 standard gives the accuracy and precision limits as both absolute and relative values. Specifications will depend on the technique
Pipetting Small Volumes
Pipetting Small Volumes Introduction Serological and micropipettes are used to accurately transfer small liquid volumes (micro-liter to milli-liter) accurately and precisely. Continuously adjustable Can
Oct 1, 2002 LAB MANUAL SPECIFIC GRAVITY & ABSORPTION of FINE AGGREGATE AASHTO Designation T 84 (Mn/DOT Modified)
Oct 1, 2002 LAB MANUAL 1205.0 1205 SPECFC GRAVTY & ABSORPTON of FNE AGGREGATE AASHTO Designation T 84 (Mn/DOT Modified) 1205.1 GENERAL This test method is intended for use in determining the bulk and apparent
Scuba Divers Science Performance Task Grades 5-8 Name: Scuba Divers
Name: Scuba Divers Two identical twins named Jill and Rachel were planning separate trips to go scuba diving. Jill planned to scuba dive in the ocean off the coast of Maine and Rachel planned to scuba
Reinforce design of experiments theory Make individual factorial designs and conduct analysis on responses
Design of Experiments Lab #2 Developed by: Mike Evangelista, Nathan Haden, Alex Jannini, Rowan University, Department of Chemical Engineering Edited by: C. Stewart Slater and Mariano Savelski, Rowan University,
Inquiry Module 1: Checking the calibration of a micropipette
Inquiry Module 1: Checking the calibration of a micropipette 1. Introduction Larger volumes (1mL and more) are usually measured using pipets or measuring cylinders. Such cylinders and pipets are labelled
The density of a substance is the same for all samples of that substance.
8.8.a Density and Buoyancy Students know density is mass per unit volume. P71 Wood Steel The density of a substance is the same for all samples of that substance. 1. The two blocks shown have the same
D. De La Matter 2004 Swimming Pool Chemistry STUDENT ACTIVITIES:
D. De La Matter 2004 Swimming Pool Chemistry STUDENT ACTIVITIES: Good News! Flinn Scientific Inc. has developed a classroom kit of experiments based on these activities. The Kit Catalog # is AP6599. Ordering
Technique Sheet 16. Using the Metric Ruler
Technique Sheet 16 Using the Metric Ruler The standard unit for length in the metric system is the meter. The meter can be divided into smaller parts and multiplied into larger units. When measuring with
Students will use two different methods to determine the densities of a variety of materials and objects.
Activity #1: Determining Densities Summary The concept of density has many useful applications. This image is an electron density map, used by biochemists to help understand the structure of a protein.
Boyle s Law VC 09. Experiment 9: Gas Laws. Abstract
Experiment 9: Gas Laws VC 09 Abstract In this laboratory activity, you will experimentally confirm Boyle s Law, determine absolute zero from Gay-Lussac's Law, and determine the molecular weight of acetone,
Aerobic Respiration. Evaluation copy
Aerobic Respiration Computer 17 Aerobic cellular respiration is the process of converting the chemical energy of organic molecules into a form immediately usable by organisms. Glucose may be oxidized completely
INTRODUCTION TO THE SPECTROPHOTOMETER AND PIPETTING SKILLS
INTRODUCTION TO THE SPECTROPHOTOMETER AND PIPETTING SKILLS Section A: Intro to the spectrophotometer A commonly used instrument in the analysis of cellular extracts is the Spectrophotometer. Today you
II. MATERIALS REQUIRED FOR PERFORMANCE TESTING
TSP-016 P/N L038-058 4-001 Rev. D February 8, 2000 Page 1 of 14 DISTRIBUTION: VistaLab Technologies Customers EQUIPMENT: MLA Pipettes SUBJECT: Pipette Performance Verification Protocol PURPOSE: To evaluate
Standard Practice for Calibration of Laboratory Volumetric Apparatus 1
Designation: E 542 0 Standard Practice for Calibration of Laboratory Volumetric Apparatus This standard is issued under the fixed designation E 542; the number immediately following the designation indicates
Enzyme Activity Lab. Wear safety goggles when handling hydrogen peroxide.
Enzyme Activity Lab This laboratory involves the use of an enzyme that will react with hydrogen peroxide. The enzyme is catalase and hydrogen peroxide (H2O2) is the substrate. The reaction is as follows:
Name:. Correct Questions = Wrong Questions =.. Unattempt Questions = Marks =
Name:. Correct Questions = Wrong Questions =.. Unattempt Questions = Marks = Lab Problem 1 Design and carry out an experiment to determine the density of the plastic object you have been given. You may
VITLAB Volumetric instruments
VITLAB Volumetric instruments Standard Operating Procedure (SOP) VITLAB GmbH Linus-Pauling-Str.1 63762 Grossostheim Germany Telefon: +49 6026 97799-0 Fax: +49 6026 97799-30 E-mail: info@vitlab.com Internet:
Gas Laws. 2 HCl(aq) + CaCO 3 (s) H 2 O(l) + CO 2 (g) + CaCl 2 (aq) HCl(aq) + NaHCO 3 (s) H 2 O(l) + CO 2 (g) + NaCl(aq)
Gas Laws Introduction: Although we cannot see gases, we can observe their behavior and study their properties. For example, we can watch a balloon filled with helium gas floating in air and conclude that
SOP No. 14. Recommended Standard Operating Procedure for Gravimetric Calibration of Volumetric Standards Using an Electronic Balance
OP No. 14 Recommended tandard Operating Procedure for Gravimetric Calibration of Volumetric tandards Using an Electronic Balance 1 Introduction 1.1 Purpose of Test This procedure is a precision mass calibration
Nadia Naghi. Hung Do. Minh Lu. George Manoli PHYS Lab 12: Archimede s Principle. July 2, 2014
1 Nadia Naghi Hung Do Minh Lu George Manoli PHYS 2125 Lab 12: Archimede s Principle July 2, 2014 2 ABSTRACT: This experiment studies the principle of density by applying Archimedes principle and calculating
BASIC LAB SKILLS: EIGHING BALANCE AND BUNSEN
Experiment 1 Name: 74 W BASIC LAB SKILLS: EIGHING BALANCE AND BUNSEN 5 B URNER This lab is designed to familiarize students with various pieces of common lab equipment. The following are general procedures
Location and Use of Safety Equipment. Extinguisher Shower Fire Blanket
Lab Safety General Guidelines No food or drink at any time Never work alone Follow all teacher instructions Read Lab Procedures before performing lab Keep work areas and aisles clear No HORSE PLAY! Location