Fixed Displacement Motor A4FM

Size: px
Start display at page:

Download "Fixed Displacement Motor A4FM"

Transcription

1 Fixed Displacement Motor 4FM RE 91 12/4. replaces: 3.95 and RE 91 1 for open and closed circuits Sizes Series 1, Series 3 Nominal pressure up to bar Peak pressure up to 45 bar Index Features 1 Ordering Code 2 echnical Data Installation and Commissioning Guidelines 4 Flow and Output orque 6 Unit Dimensions, Sizes 22, 28 7 Unit Dimensions, Size 4 8 Unit Dimensions, Size 56 9 Unit Dimensions, Size 71 1 Unit Dimensions, Size Unit Dimensions, Size Features xial Piston Fixed Displacement Motor 4FM of swashplate design is used in open and closed loop circuits for hydrostatic drives. Output speed is proportional to input flow and inversely proportional to motor displacement. Output torque increases with the pressure drop across the motor between the high and low pressure sides. Long service life, optimum efficiencies Compact design for special applications where 2FM cannot be applied Proven rotary group in swashplate-technology

2 2/12 osch Rexroth G Mobile Hydraulics 4FM RE 91 12/4. Ordering Code Hydraulic fluid Mineral oil, HFD (no code) HF, HF, HFC-Hydraulic fluid (only sizes ) E- 4F M / W xial piston unit Swashplate design, fixed displacement Mode of operation Motor 4F M Size Displacement V g (cm 3 ) Series Index Sizes , Size 71 1 Sizes Sizes Direction of rotation Viewed on shaft end alternating W Seals NR (Nitril-caoutchouc), shaft sealing in FKM (Fluor-caoutchouc) Sizes N Sizes P FKM (Fluor-caoutchouc) Sizes V Shaft end Splined shaft SE S Splined shaft SE Splined shaft DIN 548 Z Parallel with key DIN 6885 P Mounting flange SE 2-hole C ISO 4-hole ISO 8-hole H Service line connections Ports, : SE at rear (with metric fixing screws) 1 Ports, : SE at side (on opposite sides) (with metric fixing screws) 2 = available = available on enquiry = not available

3 RE 91 12/4. 4FM Mobile Hydraulics osch Rexroth G 3/12 echnical Data Fluid We request that before starting a project detailed information about the choice of pressure fluids and application conditions are taken from our catalogue sheets RE 922 (mineral oil), RE 9221 (environmentally acceptable hydraulic fluids) and RE 9223 (fire resistance fluids, HF). When using HF- or environmentally acceptable hydraulic fluids possible limitations for the technical data have to be taken into consideration. If necessary please consult our technical department (please indicate type of the hydraulic fluid used for your application on the order sheet). he sizes are not suitable for operation with HF, HF and HFC. Operation viscosity range In order to obtain optimum efficiency and service life, we recommend that the operating viscosity (at operating temperature) be selected from within the range: ν opt = operating viscosity mm 2 /s referred to the loop temperature (closed circuit) or tank temperature (open circuit). Viscosity limits he limiting values for viscosity are as follows: Size ν min =5 mm 2 /s, short term at a max. permissible temp. of t max = 115 C ν max = 1 mm 2 /s, short term on cold start (t min = -4 C) Size ν min = 1 mm 2 /s, short term at a max. permissible drain temp. t max = 9 C ν max = 1 mm 2 /s, short term on cold start (t min = -25 C) Please note that the max. fluid temperature is also not exceeded in certain areas (for instance bearing area). t temperature of -25 C up to -4 C special measures may be required for certain installation positions, please contact us. Notes on the selection of the hydraulic fluid In order to select the correct fluid, it is necessary to know the operating temperature in the loop (closed circuit) or the tank temperature (open circuit) in relation to the ambient temperature. he hydraulic fluid should be selected so that within the operating temperature range, the operating viscosity lies within the optimum range (ν opt ) (see shaded section of the selection diagram). We recommend that the highest possible viscosity range should be chosen in each case. Example: t an ambient temperature of X C the operating temperature is 6 C. Within the operating viscosity range (ν opt ; shaded area), this corresponds to viscosity ranges VG 46 or VG 68. VG 68 should be selected. Important: he leakage oil (case drain oil) temperature is influenced by pressure and motor speed and is always higher than the circuit temperature. However, at no point in the circuit may the temperature exceed 115 C for sizes or 9 C for sizes If it is not possible to comply with the above condition because of extreme operating parameters or high ambient temperatures we recommend housing flushing. Please consult us. Filtration he finer the filtration the better the achieved purity grade of the pressure fluid and the longer the life of the axial piston unit. o ensure the functioning of the axial piston unit a minimum purity grade of: 9 to NS /15 to ISO/DIS 446 is necessary. t very high temperatures of the hydraulic fluid (9 C to max. 115 C, not permissible for sizes ) at least cleanless class 8 to NS /14 to ISO/DIS 446 is necessary. If above mentioned grades cannot be maintained please consult supplier. Selection diagram viscosity ν in mm 2 /s VG 22 VG 32 VG 68 VG 46 VG ν opt temperature t in C t min = -4 C fluid temperature range t max = +115 C

4 4/12 osch Rexroth G Mobile Hydraulics 4FM RE 91 12/4. echnical Data valid for operation with mineral oils Installation and Commissioning Guidelines Flushing of the bearings (Sizes ) operating conditions, flushing quantities and notes on bearing flushing see RE 92 5 (4VSO). Operating pressure range Maximum pressure at port or (Pressure data to DIN 24312) Size Nominal pressure p N bar 1 ) 35 Peak pressure p max bar 45 1 ) 1 ) Size 28 with S-shaft: 315/35 bar he summ of the pressures at ports and may not exceed 7 bar. Direction of flow clockwise rotation to Symbol Size , Service line ports 1, 2 Case drain (1 port plugged) Size , Service line ports M,M Pressure gauge, working pressure, R(L) Case drain, ir bleed (1port plugged) U Flushing port (Sizes71...5) Case drain pressure p abs (bar) anti-clockwise rotation to Case drain pressure he max. permissible leakage pressure (housing pressure) is dependent on speed (see diagram). he pressure in the housing must be equal to or greater than the external pressure on the shaft sealing ring. Max. leakage pressure (housing pressure) p abs. max. 6 bar (sizes ) 4 bar(sizes71...5) leakage line to the tank is necessary. Size 25 Size 5 Sizes 22, 28 Sizes 4, 56 Size 71 Size 125 U M 1 M 2 R(L) General t start-up and during operation the motor housing has imperatively to be filled up with hydraulic fluid (filling of the case chamber). Startup has to be carried out at low speed and without load till the system is completely bleeded. t a longer standstill the case may discharge via operating line. t new start-up a sufficient filling of the housing has to be granted. he leakage oil in the housing has to be discharged to the tank via highest positioned case drain port. Installation position - Sizes : Shaft horizontal or shaft down - Sizes 71 (series1): Shaft horizontal, vertical installation position as to agreement - Sizes : Optional, at vertical installation position bearing flushing is recommended at port U (as to RD 925) Installation below tank level Motor below min. oil level in the tank (standard) Fill up axial piston motor before start-up via highest positioned case drain port Operate motor at low speed till motor system is completely filled up Minimum immerson depth of the drain line in the tank: mm (relative to the min. oil level in the tank) Installation on top of tank level Motor on top of min. oil level in the tank ctions as installation below tank level Note: installation position "drive shaft up" for sizes not permissible speed n (rpm)

5 RE 91 12/4. 4FM Mobile Hydraulics osch Rexroth G 5/12 echnical Data valid for operation with mineral oil able of values (theoretical values, without considering η mh and η v ; values rounded) Size Displacement V g cm Max. speed n max continuous rpm n max interm. 1 ) rpm Max. flow (at n max ) q V max L/min orque constants K Nm/bar,35,445,64,89 1,13 1,99 3,97 7,95 orque (at p = bar) max Nm ) ) ) ) Filling volume L,3,3,4,5 2, 3, 7, 11, Moment of inertia about drive axis ctual starting torque at n = rpm ( p = 35 bar) J kgm 2,15,15,43,85,121,3,959,3325 Nm (approx.) Weight (approx.) m kg ) Intermittent max. speed at overspeed: p = 7 15 bar 2 ) p = 35 bar Calculation of size Flow q v = V g n 1 η v in L/min q V 1 ηv Output speed n = V g p η mh Output torque = in Nm 2 π V g V g = geometric displacement per rev. in cm 3 p = pressure differential in bar n = speed in rpm η v η mh η t = volumetric efficiency = mech.-hyd. efficiency = overall efficiency = K p η mh n 2 π n Output power P = = in kw q v p η = t Output drive permissible axial and radial loading on drive shaft Size Distance of F q F q a mm 17,5 17,5 17,5 17,5 (from shaft shoulder) b mm a, b, c c mm 42,5 42,5 42,5 42,5 Max. permissible radial force at distance a F q max N b F q max N c F q max N Max. permissible axial load - - F ax max N F ax + + F ax max N Size Max. axial force at housing pressure p max 1 bar abs. F q ± F ax max N Max. axial force at housing pressure p max 4 bar abs. ± F ax + F ax max N X/2 X/2 F ax max N X Max. radial force F q max N

6 6/12 osch Rexroth G Mobile Hydraulics 4FM RE 91 12/4. Flow and Drive orque Size 71 Size 5 flow q V (L/min) 3 1 n = 15 rpm n = 3 rpm q V 3 1 drive torque (Nm) flow q V (L/min) n = 1 rpm n = 18 rpm drive torque (Nm) Size 125 flow q V (L/min) n = 15 rpm n = 2 rpm p (bar) 7 5 drive torque (Nm) q V q V Size 25 flow q V (L/min) p (bar) 7 5 n = 15 rpm n = 2 rpm q V drive torque (Nm) p (bar) p (bar) (Fluid: Hydraulic oil ISO VG 46 DIN 51519, t = 5 C)

7 RE 91 12/4. 4FM Mobile Hydraulics osch Rexroth G 7/12 Unit Dimensions, Size 22, 28 efore finalising your design, please request a certified drawing. (SE ), M8; 15 deep Connections, Service line ports SE 1 / 2 " 42 bar ( psi) high pressure series 1, 2 Leakage port / oil filling port M18x1,5; 12 deep Shaft ends S Splined shaft SE 7 / 8 ", 3 pressure angle, 13 teeth, 16/32 pitch, flat root, side fit, tolerance class 5 NSI 92.1a-1976 ø55 5/16-18UNC ø17,7 Splined shaft SE 1" 3 pressure angle, 15 teeth, 16/32 pitch, flat root, side fit, tolerance class 5 NSI 92.1a-1976 ø55 3/8-16UNC ,5 22 ø2,8 41,3 46

8 8/12 osch Rexroth G Mobile Hydraulics 4FM RE 91 12/4. Unit Dimensions, Size 4 efore finalising your design, please request a certified drawing. 1, 1 (SE ) 2 M1; 17 deep 2 Connections, Service line ports SE 3 / 4 " 42 bar ( psi) high pressure serie, 1, 2 Leakage port / oil filling port M18x1,5; 15 deep Shaft ends Z Splined shaft W 3x2x3x14x9g DIN 548

9 RE 91 12/4. 4FM Mobile Hydraulics osch Rexroth G 9/12 Unit Dimensions, Size 56 efore finalising your design, please request a certified drawing. 12, , ø127 (SE C) 48 X ; 2 25,4 61 Connections, Service line ports SE 3 / 4 " 42 bar ( psi) high pressure serie, 1, 2 Leakage port / oil filling port M 18x1,5 ; 12 deep 23, View X 5,8 ø19 M1; 17 deep Shaft ends Z Splined shaft W 3x2x3x14x9g DIN 548

10 1/12 osch Rexroth G Mobile Hydraulics 4FM RE 91 12/4. Unit Dimensions, Size 71 efore finalising your design, please request a certified drawing R(L) port plate 1 ø15 ø14h8 61 M X h9 ø M Y port plate 2 View Y port plate 1 View X ø25 M M , ø M12; 17 deep to mounting flange267 Y M12; 17 deep 57.2 Connections, service line ports SE 1" (high pressure series) R (L) oil filling and bleed M27x2 oil drain (plugged) M27x2 M, M measuring port for pressure (plugged) M14x1,5 Shaft end P Parallel shaft with key S 12x8x68 DIN 6885 ø4k6 M12 1,5 68 9,5 Z Splined shaft W4x2x3x18x9g DIN 548 M , R1,6 55

11 RE 91 12/4. 4FM Mobile Hydraulics osch Rexroth G 11/12 Unit Dimensions, Size 125 efore finalising your design, please request a certified drawing R(L) port plate 1 12 ø2 U M h9 ø ø16h8 74 X M Y port plate 2 View Y port plate 1 View X ø32 M M , 31.8 ø M14; 19 deep to mounting flange 35 Y M14; 19 deep 66.7 Connections, service line ports SE 1 1 / 4 " (high pressure series) R (L) oil filling and bleed M33x2 oil drain (plugged) M33x2 M, M measuring port for pressure (plugged) M14x1,5 U Flushing port, M14x1,5 flushing of the bearings (plugged) Shaft end P Parallel shaft with key 14x9x8 DIN 6885 ø5k6 M16 1, Z Splined shaft W5x2x3x24x9g DIN 548 M R2,

12 12/12 osch Rexroth G Mobile Hydraulics 4FM RE 91 12/4. Unit Dimensions, Size 25 efore finalising your design, please request a certified drawing R(L) port plate ø24 U M h9 ø28 ø224h8 91 X M M M Y port plate View Y, ø M16; 21 deep port plate 1 View X to mounting flange Shaft end P Parallel shaft with key S 18x11x1 DIN 6885 ø6m6 M2 Y M16; 21 deep Connections, service line ports SE 1 1 / 2 " (high pressure series) R (L) oil filling and bleed M42x2 oil drain (plugged) M42x2 M, M measuring port for pressure (plugged) M14x1,5 U Flushing port, M14x1,5 flushing of the bearings (plugged) Z Splined shaft W6x2x3x28x9g DIN 548 M R4 42 8

Fixed Displacement Motor A4FM

Fixed Displacement Motor A4FM Industrial Hydraulics Electric Drives and Controls Linear Motion and ssembly echnologies Pneumatics Service utomation Mobile Hydraulics Fixed Displacement Motor 4FM RE 91 12/4. replaces: 3.95 and RE 91

More information

Fixed Displacement Plug-In Motor A2FE

Fixed Displacement Plug-In Motor A2FE www.phphyds.com Series 6, axial tapered piston, bent axis design for mounting in mechanical gearboxes Sizes 28...355 Nom. Pressure up to 400 bar Peak Pressure up to 450 bar he fixed displacement plug-in

More information

Variable Displacement Double Pump A20VO. Series 1, for open circuits Axial piston - swashplate design, Back to back - design

Variable Displacement Double Pump A20VO. Series 1, for open circuits Axial piston - swashplate design, Back to back - design Brueninghaus Hydromatik Series 1, for open circuits Axial piston - swashplate design, Back to back - design RE 93100/02.97 Sizes 60...260 Nominal Pressure up to 350 bar Peak Pressure up to 400 bar Preliminary

More information

Dual displacement motor A10VM Plug-in dual displacement motor A10VE for open and closed circuit applications

Dual displacement motor A10VM Plug-in dual displacement motor A10VE for open and closed circuit applications Replaces: 04.95 Dual displacement motor 10VM Plug-in dual displacement motor 10VE for open and closed circuit applications Size 28-60 Series 5 Nominal pressure 280 bar Peak pressure 350 bar 10VM Contents

More information

Fixed Displacement Pump KFA for commercial vehicles in open circuits

Fixed Displacement Pump KFA for commercial vehicles in open circuits RE 91 501/05.98 Replaces: 11.96 Fixed Displacement Pump KFA for commercial vehicles in open circuits Sizes 23...107 Series 6 Nominal pressure 300 bar Peak pressure 350 bar KFA List of contents Features

More information

Axial piston variable motor A10VM Plug-in version A10VE

Axial piston variable motor A10VM Plug-in version A10VE Electric Drives and Controls Hydraulics inear Motion and ssembly Technologies Pneumatics Service xial piston variable motor 10VM Plug-in version 10VE RE 91703/06.09 1/28 Replaces:09.07 Data sheet Series

More information

Variable Displacement Pump A10VO

Variable Displacement Pump A10VO Brueninghaus Hydromatik Variable Displacement Pump A1VO Series 5, open circuits, SAE-Version Axialpiston, swash plate design size 28 6 Nominal pressure 2 bar Peak pressure 315 bar RE 9273/4.96 replaces

More information

Axial piston-variable motor A10VM Plug-in version A10VE

Axial piston-variable motor A10VM Plug-in version A10VE Electric Drives and Controls Hydraulics inear Motion and ssembly Technologies Pneumatics Service xial piston-variable motor 10VM Plug-in version 10VE R 91703/06.09 1/28 Replaces:11.07 Technical Data Sheet

More information

OMS Technical Information. Versions OMS. Versions

OMS Technical Information. Versions OMS. Versions Versions Versions Mounting flange Shaft Port size European version US version Drain connection Check valve Main type designation Standard flange Cyl. 32 G 1/2 l Yes Yes Cyl. 1.25 in 7/8-14 UNF l Yes Yes

More information

APPLICATION. Conveyors Metal working machines Machines for agriculture Road building machines Mining machinery Food industries

APPLICATION. Conveyors Metal working machines Machines for agriculture Road building machines Mining machinery Food industries HYDRAULIC APPLICATION Conveyors Metal working machines Machines for agriculture Road building machines Mining machinery Food industries Special vehicles Plastic and rubber machinery etc. CONTENTS Specification

More information

Displacement 12, , Maximum flow rate (at 1450 rpm) bar.

Displacement 12, , Maximum flow rate (at 1450 rpm) bar. 00/07 ED PVD VARIABLE DISPLACEMENT VANE PUMPS SERIES 0 OPERATING PRINCIPLE The PVD pumps are variable displacement vane pumps with a mechanical type of pressure compensator. They allow instantaneous adjustment

More information

VPPL VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS FOR INTERMEDIATE PRESSURE SERIES 10

VPPL VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS FOR INTERMEDIATE PRESSURE SERIES 10 / ED VPPL VARIABLE DISPLACEMENT AXIAL-PISTON PUMPS FOR INTERMEDIATE PRESSURE SERIES OPERATING PRINCIPLE The VPPL are variable displacement axial-piston pumps with variable swash plate, suitable for applications

More information

Axial Piston Variable Pump A10V(S)O (US-Version)

Axial Piston Variable Pump A10V(S)O (US-Version) Axial Piston Variable Pump A1V()O (U-Version) RA-A 9271/3.12 1/52 Replaces: 12.9 Data sheet eries 31 ize NG18 ((A)A1VO) ize NG28 to 14 (A1VO) Nominal pressure 4 psi (28 bar) Maximum pressure 51 psi (35

More information

OMS Technical Information Technical data

OMS Technical Information Technical data Technical data TECHNICAL DATA FOR OMS Type OMS OMS OMS OMS OMS OMS OMS OMS OMS OMSW OMSW OMSW OMSW OMSW OMSW OMSW OMSW OMSW OMSS OMSS OMSS OMSS OMSS OMSS OMSS OMSS OMSS Motor size 80 100 125 160 200 250

More information

Axial piston pumps type PVPY-C (-R, -L) variable displacement, with mechanical controls obsolete components - availability on request

Axial piston pumps type PVPY-C (-R, -L) variable displacement, with mechanical controls obsolete components - availability on request www.atos.com Table TA60obs/E Axial piston pumps type PVPY- (-R, -) variable displacement, with mechanical controls obsolete components - availability on request PVPY are variable displacement axial piston

More information

Controllers DR, DP, FR and DFR

Controllers DR, DP, FR and DFR Controllers DR, DP, FR and DFR RE 9060 Edition: 04.014 Replaces: 10.006 For variable pump A4VSO series 1 and 3 Open circuit Features Control of pressure and flow Remote controlled optional Pressure controller

More information

-for information only- noncommittal. Axial Piston Variable Pump A10VSO RA / /24. Technical Data Sheet

-for information only- noncommittal. Axial Piston Variable Pump A10VSO RA / /24. Technical Data Sheet Electric Drives and Controls Hydraulics inear Motion and Assembly Technologies Pneumatics ervice Axial Piston Variable Pump A10VO Technical Data heet ize 71... 180 eries 32 Nominal pressure 4000 psi (280

More information

HYDRAULIC MOTORS MV APPLICATION GENERAL

HYDRAULIC MOTORS MV APPLICATION GENERAL HYDRAULIC V APPLICAION» Conveyors» etal working machines» Agriculture machines» Road building machines» ining machinery» Food industries» Special vehicles» Plastic and rubber machinery etc. CONENS Specification

More information

HYDRAULIC MOTORS MTM APPLICATION OPTIONS CONTENTS EXCELLENCE GENERAL

HYDRAULIC MOTORS MTM APPLICATION OPTIONS CONTENTS EXCELLENCE GENERAL HYDRAULIC OORS APPLICAION» Skid Steer Loaders» etal working machines» renchers» Augers» Agricultural machines» Road building machines» Special vehicles» ine machines» Woodworking and sawmill machinery»

More information

Axial piston pumps type PVC

Axial piston pumps type PVC www.atos.com Table TA16-1/E Axial piston pumps type PV variable displacement, by a full line of mechanical controls PV are variable displacement axial piston pumps for medium pressure operation, low noise

More information

Axial piston pumps type PVC

Axial piston pumps type PVC www.atos.com Table TA16SK-1/E Axial piston pumps type PV variable displacement, by a full line of mechanical controls PV are variable displacement axial piston pumps for medium pressure operation, low

More information

E 328 E 498 Tank top mounting Connection up to G1½ / -24 SAE and SAE 2 Nominal flow rate up to 600 l/min / gpm

E 328 E 498 Tank top mounting Connection up to G1½ / -24 SAE and SAE 2 Nominal flow rate up to 600 l/min / gpm Return-Suction Filters E 8 E 98 Tank top mounting Connection up to G½ / - SE and SE Nominal flow rate up to 6 l/min / 8. gpm Description pplication For operation in units with hydrostatic drives, when

More information

E 328 E 498 Tank top mounting Connection up to G1½ and SAE 2 Nominal flow rate up to 600 l/min

E 328 E 498 Tank top mounting Connection up to G1½ and SAE 2 Nominal flow rate up to 600 l/min Return-Suction Filters E 8 E 98 Tank top mounting Connection up to G½ and SE Nominal flow rate up to 6 l/min Description pplication For operation in units with hydrostatic drives, when the return flow

More information

DENISON HYDRAULICS vane pumps - single, double T6G - T67G - T6ZC

DENISON HYDRAULICS vane pumps - single, double T6G - T67G - T6ZC DENISON HYDRAULICS vane pumps - single, double T6G - T67G - T6ZC Publ. 1 - EN0709 - A 01 / 2000 / 2500 / FB Replaces : 1 - EN 084 - B L25-10709 - 1 CONTENTS GENERAL CHARACTERISTICS T67GB T6GC - T6ZC T67GB

More information

Orbital Motors Type OMP, OMR and OMH. Technical Information

Orbital Motors Type OMP, OMR and OMH. Technical Information Orbital Motors Type OMP, OMR and OMH Technical Information OMP, OMR and OMH Contents Revision View Date Page Changed Revision Mar 26 Small updates B Jun 27 all Major revision with new lit-number (minus

More information

Brueninghaus Hydromatik Rexroth A11VLO pump and A11VO pump

Brueninghaus Hydromatik Rexroth A11VLO pump and A11VO pump Brueninghaus Hydromatik Rexroth A11VLO pump and A11VO pump www.hydpump.com A11VLO40, A11VLO60, A11VLO75, A11VLO95, A11VLO130, A11VLO145, A11VLO190, A11VLO260. A11VO40, A11VO60, A11VO75, A11VO95, A11VO130,

More information

Hydraulic Motor/Pump. Series F11/F12 Fixed Displacement

Hydraulic Motor/Pump. Series F11/F12 Fixed Displacement Hydraulic Motor/Pump Fixed Displacement Specifications size F11-5 -6-10 -12-14 -19 Displacement [cm 3 /rev] 4.9 6.0 9.8 12.5 14.3 19.0 Operating pressure max intermittent 1) [bar] 420 420 max continuous

More information

Orbital Motors Type OMP X and OMR X

Orbital Motors Type OMP X and OMR X Technical Information Orbital Motors Type OMP X and OMR X powersolutions.danfoss.com Revision history Table of revisions Date Changed Rev January 218 Major revision. 21 February 217 First edition. 11 2

More information

Orbital Motors OMS, OMT and OMV

Orbital Motors OMS, OMT and OMV MKING MODERN LIVING POSSIBLE Technical Information Orbital Motors OMS, OMT and OMV powersolutions.danfoss.com Revision history Table of revisions Date Changed Rev February 216 Corrected Hardening specification

More information

DISC VALVE HYDRAULIC MOTORS

DISC VALVE HYDRAULIC MOTORS DISC VALVE HYDRAULIC CONTENTS Page Hydraulic otors Series S... 4 Hydraulic otors Series T... 25 Hydraulic otors Series V... 39 otor Special Features... 51 otors with Speed Sensor... 52 Application Calculation...

More information

E 084 Tank top mounting Connection up to G1 / -16 SAE Nominal flow rate up to 80 l/min / 21.1 gpm

E 084 Tank top mounting Connection up to G1 / -16 SAE Nominal flow rate up to 80 l/min / 21.1 gpm Return-Suction Filters E 08 Tank top mounting Connection up to G / -6 SE Nominal flow rate up to 80 l/min /. gpm Description pplication For operation in units with hydrostatic drives, when the return flow

More information

Auxiliary valve QDS6 Sequence valve, 3-way. Catalogue (GB) (US) October 1998

Auxiliary valve QDS6 Sequence valve, 3-way. Catalogue (GB) (US) October 1998 Auxiliary valve Sequence valve, 3-way Catalogue 9129 8542-02 (GB) 9129 8542-06 (US) October 1998 Sequence valve, 3-way Applications The sequence valve is designed to open or close a hydraulic pilot signal

More information

Pressure reducing valve, pilot operated, Model 3DR

Pressure reducing valve, pilot operated, Model 3DR RA 26 928/06.98 Pressure reducing valve, pilot operated, Model 3DR Nominal size 16 Series 5X Maximum operating pressure 3600 PSI (250 bar) Maximum flow 58.1 GPM (220 L/min) Contents Description Page Features

More information

Inverse Proportional Pressure-Relief Cartridge, Size 10

Inverse Proportional Pressure-Relief Cartridge, Size 10 Inverse Proportional Pressure-Relief Cartridge, Size 1 Q max = 12 l/min, p max = 3 bar Seated pilot, spool-type main stage, damped design 1 Description inverse-proportional pressure-relief valves are size

More information

Inverse Proportional Pressure-Relief Cart., Size 2 4

Inverse Proportional Pressure-Relief Cart., Size 2 4 Inverse Proportional Pressure-Relief Cart., Size Q max = l/min, p max = 5 bar Direct acting, electrically operated 1 Description inverse proportional pressure-relief valves are direct acting screw-in cartridges

More information

OMS, OMT and OMV Orbital Motors. Technical Information

OMS, OMT and OMV Orbital Motors. Technical Information , OMT and OMV Orbital Motors Technical Information , OMT and OMV A Wide Range of Orbital Motors Revision History Table of Revisions Date Page Changed Rev ED Dimensions changed EF A Wide Range of Orbital

More information

GEAR PUMPS. Displacement from 5 to 39 ccm Pressure up to 280 bar Speed from 400 to 3000 RPM

GEAR PUMPS. Displacement from 5 to 39 ccm Pressure up to 280 bar Speed from 400 to 3000 RPM Displacement from 5 to 39 ccm Pressure up to 280 bar Speed from 400 to 3000 PM GEA PUMPS TABE OF CONTENTS DESCIPTION......................................................................................................................

More information

OMS, OMT and OMV Orbital Motors. Technical Information

OMS, OMT and OMV Orbital Motors. Technical Information OMS, OMT and OMV Orbital Motors Technical Information OMS, OMT and OMV A Wide Range of Orbital Motors F300540.eps F300030.TIF A wide range of orbital motors Sauer-Danfoss is a world leader within production

More information

Inverse Proportional Pressure-Relief Cart., Size 2 4

Inverse Proportional Pressure-Relief Cart., Size 2 4 Inverse Proportional Pressure-Relief Cart., Size Q max = l/min, p max = 35 bar Direct acting, electrically operated Description Compact construction for cavity type AL 3/-6 UNF Operated by a proportional

More information

Inverse Prop. Pressure-Relief Cart., Size 2 4

Inverse Prop. Pressure-Relief Cart., Size 2 4 Inverse Prop. Pressure-Relief Cart., Size Q max = l/min (6 gpm), p max = bar (58 psi) Direct acting, electrically operated Description inverse proportional pressure-relief valves are direct acting screw-in

More information

PLD 03 T A CASAPPA S.p.A.

PLD 03 T A CASAPPA S.p.A. GEAR FLOW DIVIDERS INDEX Section Page GENERAL FEATURES... 3 GENERAL DATA... 5 FLOW EQUALIZER... 6 FLOW DIVIDERS... 8 TYPICAL CIRCUITS... 10 NOTES ABOUT COMPOSITION... 12 PORTS DIMENSIONS.... 14 GROUP DIMENSIONS...

More information

Proportional Pressure-Relief Cartridge Valve, Size 2...4

Proportional Pressure-Relief Cartridge Valve, Size 2...4 Proportional Pressure-Relief Cartridge Valve, Size... Q max = l/min, p max = 3 bar Direct acting, electrically operated 1 Description proportional pressure-relief valves are direct acting screw-in cartridges

More information

Variable displacement vane pump (with mechanical pressure compensator)

Variable displacement vane pump (with mechanical pressure compensator) Variable displacement vane (with mechanical pressure compensator) PVS-Type Key Features: Rotation: Right (viewed from shaft end) Mounting flanges: 4-hole flange (UNI ISO 319/2) onnections: GS SP (UNI ISO

More information

Leak free Pipe Rupture Valve for Excavators

Leak free Pipe Rupture Valve for Excavators Leak free Pipe Rupture Valve for xcavators Series motion and progress Reference: 3 P 9575 1/11.6 Classification: 43.325.355...325.35 1/17 Contents Page 1 General description................................................................

More information

Displacement. from 2 up to 6 sections balanced, unbalanced from 0.8 to 31 ccm FLOW DIVIDERS

Displacement. from 2 up to 6 sections balanced, unbalanced from 0.8 to 31 ccm FLOW DIVIDERS Displacement from 2 up to 6 sections balanced, unbalanced from 0.8 to 31 ccm FLOW DIVIDERS DP Catalogue of flow dividers DP TABLE OF CONTENTS GENERAL DESCRIPTION........................................................................................................

More information

Pressure reducing valve, pilot operated

Pressure reducing valve, pilot operated Pressure reducing valve, pilot operated RE 26928/09.07 Replaces: 10.97 1/8 Type 3DR Size 16 Component series 5X Maximum operating pressure 250 bar Maximum flow 220 l/min H5844 Table of contents Content

More information

DENISON HYDRAULICS high performance hydraulic vane pumps single, double, triple T7 and T67 industrial application

DENISON HYDRAULICS high performance hydraulic vane pumps single, double, triple T7 and T67 industrial application Back to Content DENISON HYDRAULICS high performance hydraulic vane pumps single, double, triple T7 and T67 industrial application Publ. 1 - EN 079 - B 01 / 97 / 3000 / FB Replaces : 1 - EN 079 - A CONTENTS

More information

Pressure reducing valve, direct operated

Pressure reducing valve, direct operated Electric Drives and Controls Table of contents Hydraulics Pressure reducing valve, direct operated Model DR 10 DP Nominal size 10 Series 4X Maximum reduced pressure 210 bar (3050 PSI) Maximum flow 80 L/min

More information

Pressure reducing valve, direct operated

Pressure reducing valve, direct operated Electric Drives and Controls Table of contents Hydraulics Pressure reducing valve, direct operated Model ZDR 6 D Nominal size 6 Series 4X Maximum operating pressure 20 bar (3050 PSI) Maximum flow 50 L/min

More information

Vickers. Flow Controls. Flow Controls FN, F(C)G, FRG. Released 6/94

Vickers. Flow Controls. Flow Controls FN, F(C)G, FRG. Released 6/94 Vickers Flow Controls Flow Controls FN, F(C)G, FRG Released 6/94 685 Table of Contents FN03/06/10 Model Series Application Data...............................................................................

More information

ENGINEERING DATA. PVB Piston Pumps. w w w. F l u i D y n e F P. c o m Same Day Shipments of Units or Part Orders

ENGINEERING DATA. PVB Piston Pumps. w w w. F l u i D y n e F P. c o m Same Day Shipments of Units or Part Orders ENGINEERING DT PV Piston Pumps Same Day Shipments of Units or Part Orders Interchangeable Parts Fully Tested w w w. F l u i D y n e F P. c o m Email:cs@FluiDyneFP.com Contents asic characteristics.........................................................................................

More information

Proportional Pressure-Relief Cartridge Valve, Size 2...4

Proportional Pressure-Relief Cartridge Valve, Size 2...4 Proportional Pressure-Relief Cartridge Valve, Size... Q max = l/min (6 gpm), p max = bar (58 psi) Direct acting, electrically operated Description proportional pressure-relief valves are direct acting

More information

PVQ 13 A2 R SE 1 S 20 C-11 D

PVQ 13 A2 R SE 1 S 20 C-11 D PVQ - Variable Displacement Piston Pump PVQ 13 A2 R SE 1 S 2 C-11 D 1 2 3 4 6 7 8 9 1 1 Model Series PVQ Inline Piston Pump Variable Volume Quiet Series 4 Rotation Viewed from shaft end R Right hand, standard

More information

Sauer Danfoss Series 90 Hydraulic Axial Piston Pump

Sauer Danfoss Series 90 Hydraulic Axial Piston Pump Sauer Danfoss Series 90 Hydraulic Axial Piston Pump www.hydpump.com 90R030, 90R042, 90R055, 90R075, 90R100, 90R130, 90R180, 90R250 90L030, 90L042, 90L055, 90L075, 90L100, 90L130, 90L180, 90L250 Series

More information

DENISON HYDRAULICS T6 industrial application

DENISON HYDRAULICS T6 industrial application DENISON HYDRAULICS T6 industrial application vane pumps - single, double, triple Publ. 1 - EN0700 - B 10 / 2000 / FB Replaces : 1 - EN0700 - A L13-10700 - 2 CONTENTS - T6 SERIES INDUSTRIAL APPLICATION

More information

Introduction INDEX. INTRODUCTION HSE

Introduction INDEX.  INTRODUCTION HSE Introduction INDEX SECTION PAGE INTRODUCTION ORDERING CODE GLOSSARY MOTOR OPTION TECHNICAL SE SE3 / SE5 SE7 / S7 SE9 / S9 SE12 / S12 SE14 / S14 SE14-2 / S14-2 SE17 / S17 SE17-2 / S17-2 SE21 / S21 SE21-2

More information

E 212 E 222 Tank top mounting Connection up to G1¼ / -20 SAE Nominal flow rate up to 220 l/min / 58.1 gpm

E 212 E 222 Tank top mounting Connection up to G1¼ / -20 SAE Nominal flow rate up to 220 l/min / 58.1 gpm Return Filters E E Tank top mounting Connection up to G¼ / - SE up to l/min / 8. gpm Description pplication In the return line circuits of hydraulic systems. erformance features rotection against wear:

More information

E 158 E 198 E 248. Tank top mounting Connection up to G11 / 4 Nominal flow rate up to 250 l/min e d

E 158 E 198 E 248. Tank top mounting Connection up to G11 / 4 Nominal flow rate up to 250 l/min e d R e t u r n - S u c t i o n F i l t e rs E 158 E 198 E 248 Tank top mounting Connection up to G11 / 4 Nominal flow rate up to 250 l/min 20.90-5e 0.0-2d D e s c r i p t i o n Application For operation in

More information

Orbital Motors Type VMP. Technical Information

Orbital Motors Type VMP. Technical Information Orbital Motors Type VMP Technical Information A Wide Range of Orbital Motors Revision View Date Page Changed Revision May 213 All First edition AA F31 245 A Wide Range of Orbital Motors Sauer-Danfoss is

More information

Pump safety block. Type DBA, DBAW, DBAE(E) Features. Contents. RE Edition: Replaces: 11.10

Pump safety block. Type DBA, DBAW, DBAE(E) Features. Contents. RE Edition: Replaces: 11.10 ump safety block ype D, DW, DE(E) RE 25891 Edition: 2013-05 Replaces: 11.10 Size 16, 25, 32 Component series 2 Maximum operating pressure 350 bar Maximum flow 400 l/min H5872 Features Depressurized start-up

More information

MAKING MODERN LIVING POSSIBLE. Technical Information. Orbital Motor VMP. powersolutions.danfoss.com

MAKING MODERN LIVING POSSIBLE. Technical Information. Orbital Motor VMP. powersolutions.danfoss.com MAKING MODERN LIVING POSSIBLE Technical Information Orbital Motor VMP powersolutions.danfoss.com Revision History Table of Revisions Date Changed Rev Feb 214 New dimension drawings. Converted to Danfoss

More information

Orbital Motors OMSW with brake nose

Orbital Motors OMSW with brake nose MAKING MODERN LIVING POSSIBLE Technical Information Orbital Motors OMSW with brake nose powersolutions.danfoss.com Revision history Table of revisions Date Changed Rev October 214 Changed to Danfoss layout

More information

DISC VALVE HYDRAULIC MOTORS

DISC VALVE HYDRAULIC MOTORS DISC VALVE HYDRAULIC DISC VALVE 's function is to distribute fluid to the Roller Gear Set. The pressure balanced sealing surface on the valve face and the separately driven maintains minimal leakage and

More information

4/3 Directional valve elements L8_P5 with proportional (ED-IP) control and with or without LS connections L8_P5 (ED-IP)

4/3 Directional valve elements L8_P5 with proportional (ED-IP) control and with or without LS connections L8_P5 (ED-IP) 4/3 Directional valve elements L8_5 with proportional (ED-I) control and with or without LS connections L8_5 (ED-I) RE 1831-7 Edition: 2.21 Replaces: 7.12 7.212 Size Series Maximum operating pressure 31

More information

Electrically Operated Pressure-Relief Cartridge, Size 10

Electrically Operated Pressure-Relief Cartridge, Size 10 Electrically Operated Pressure-Relief Cartridge, Size 1 Q max = 14 l/min (37 gpm), p max = bar (5 psi) seated pilot stage, spool-type design, with remote contral port Z Series WUVPOC-2, WUVPLC-2 1 Description

More information

Pressure relief valve, direct operated

Pressure relief valve, direct operated Pressure relief valve, direct operated RE 570/0.05 Replaces: 06.03 /8 Type DBD..K Size Component series X Maximum operating pressure 500 bar Maximum flow 0 l/min K9- Table of contents Contents Page Features

More information

RCOe 1806/ PARKER CALZONI Radial Piston Motor Type MR, MRE

RCOe 1806/ PARKER CALZONI Radial Piston Motor Type MR, MRE RCOe 86/9. PARKER CALZONI Radial Piston otor Type R, RE TABLE OF CONTENTS OTOR TYPE R RE CONTENTS PAG. TABLE OF CONTENTS GENERAL CHARACTERISTICS FUNCTIONAL DESCRIPTION TECHNICAL DATA FLUID SELECTION 6

More information

Prop. 3-Way Pressure-Reducing Cart., Size 5 / SAE 08

Prop. 3-Way Pressure-Reducing Cart., Size 5 / SAE 08 Prop. -Way Pressure-Reducing Cart., Size / SAE 8 Q max = 1 l/min (4 gpm), p max = bar (6 psi) Direct acting, electrically operated 1 Description proportional -way pressure-reducing cartridges are size

More information

Industrial Hydraulic Pumps T6EDC. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement

Industrial Hydraulic Pumps T6EDC. We are doing our parts to keep you moving! Denison Vane Technology, fixed displacement Industrial Hydraulic Pumps T6EDC Denison Vane Technology, fixed displacement Hydraulic Pumps Hydraulic Motors Hydraulic Valves Hydraulic Cylinders Hydraulic Filtration Hydraulic Accumalators We are doing

More information

Proportional Throttle Cartridges, Size 16

Proportional Throttle Cartridges, Size 16 Proportional Throttle Cartridges, Size 16 Q max = 5 l/min, p max = 5 bar, Q N max = 14 l/min at p 1 bar Two-Stage, with Seat-Valve Shut-Off 1 Description Normally closed Seat-valve shut-off from 1 Compact

More information

Check valve hydraulically pilot operated

Check valve hydraulically pilot operated Check valve hydraulically pilot operated RE 6/7.5 Replaces:. / Types SV and SL Nominal sizes to Component series X Maximum operating pressure 5 bar Maximum flow 55 l/min H555 Overview of contents Contents

More information

Pressure reducing valve, direct operated, type DR 5 DP Huade América 1

Pressure reducing valve, direct operated, type DR 5 DP Huade América 1 Pressure reducing valve, direct operated, type DR 5 DP Huade América 1 BEIJING HUADE HYDRAULIC INDUSTRIAL GROUP CO.,LTD. Pressure reducing valve, direct operated, type DR 5 DP Size 5 up to 31.5MPa up to

More information

420 Mobile Piston Pump Design Code B

420 Mobile Piston Pump Design Code B 42 Mobile Piston Pump Design Code B ADU41 ADU49 ADU62 ADU8 Introduction 42 Series Mobile Piston Pump Eaton s 42 Series mobile pumps are open circuit, axial piston designs with displacements of 41cc, 49cc,

More information

D 042 D 062 In-line mounting Operating pressure up to 100 bar Nominal flow rate up to 90 l/min

D 042 D 062 In-line mounting Operating pressure up to 100 bar Nominal flow rate up to 90 l/min Pressure Filters D D 6 In-line mounting Operating pressure up to 1 bar Nominal flow rate up to 9 l/min Description Application In the pressure circuits of hydraulic and lubrication systems. Performance

More information

Hand & mechanical directional valves

Hand & mechanical directional valves www.atos.com Table E5-3/E Hand & mechanical directional valves ISO 44 sizes 6,, 6 and 25 H- Hand & mechanical operated directional valves are spool type, three or four way, two or three position valves,

More information

Directional Controls

Directional Controls Vickers Directional Controls Directional Control Valves DG3V-3-*-60 Hydraulic Operated DG17V-3-*-60 Lever Operated DG18V-3-*-60 Air Operated DG20V-3-*-60 Cam Operated DG21V-3-*-60 Plunger Operated CETOP

More information

E Series Piston Pumps Variable Displacement Series for Mobile Applications Technical Catalog PVE012 PVE19 PVE21

E Series Piston Pumps Variable Displacement Series for Mobile Applications Technical Catalog PVE012 PVE19 PVE21 E Series Piston Pumps Variable Displacement Series for Mobile Applications Technical Catalog PVE012 PVE19 PVE21 Table of Contents Introduction......................................................................................................

More information

BW0500AO. ByWire Elements BW0500AO Element 4/3 with side ports IBW0500 Interface

BW0500AO. ByWire Elements BW0500AO Element 4/3 with side ports IBW0500 Interface ywire Elements Element 4/3 with side ports IW5 Interface efore use, carefully read the GENERL INSTRUCTIONS FOR USE OF DIRECTIONL CONTROL VLVES 398SW5EN - 5--8 Technical data Nominal flow 5 l/min 3. US

More information

3-Way Pressure-Reducing Cartridge, Size 2 4

3-Way Pressure-Reducing Cartridge, Size 2 4 -Way Pressure-Reducing Cartridge, Size 2 Q max = 2 l/min, p max = 25 bar Spool-type design, direct acting, with manual adjustment 1 Description Compact construction for cavity type AM /- UNF to Bucher

More information

PRESSURE SEQUENCE VALVE TYPE UZK

PRESSURE SEQUENCE VALVE TYPE UZK PRESSURE SEQUENCE VALVE TYPE UZK Size 10, 20, 30 31,5 MPa up to 450 dm 3 /min WK 450 414 04. 2000r. Pressure sequence valves type UZK are used for switching a system or part of a system off when a set

More information

DNS. Monoblock directional control valves DNS - Directional control valve

DNS. Monoblock directional control valves DNS - Directional control valve Monoblock directional control valves DNS - Directional control valve DNS efore use, carefully read the GENERL INSRUCIONS FOR USE OF DIRECIONL CONROL VLVES 398SMD6I - 6--8 DNS echnical data Nominal flow

More information

Double Pilot Operated Cartridge Check Valve, Size 8

Double Pilot Operated Cartridge Check Valve, Size 8 Double Pilot Operated Cartridge Check Valve, Size 8 Q max = 7 l/min (19 gpm), p max = 35 bar (5 psi) pilot operated, two-stage, spring-closed cartridge-type poppet valve Compact design for cavity type

More information

Cooler-Bypass Thermostat Valve, Size 16

Cooler-Bypass Thermostat Valve, Size 16 Cooler-Bypass hermostat Valve, Size Q max = l/min, p max = bar emperature-controlled, integral relief function, various pressure settings available Description emperature-dependent bypass control Integral

More information

Priority (Swing) Motors Data and Specifications

Priority (Swing) Motors Data and Specifications s Data and Specifications Specifications HMF 55 HMF 75 HMF 105 cm 3/rev in 3/rev 55 3.36 75 4.57 105 6.40 Pressure Ratings Nominal 5000 PSIG Maximum 6090 PSIG Peak 7250 PSIG Operating Speed Maximum 4100

More information

2-way flow control valve Model 2FRM 6

2-way flow control valve Model 2FRM 6 R 28 6/0.98 Replaces R 28 62/05.94 R 28 6/06.98 2-way flow control valve Model 2FRM 6 Nominal size 6 Series X Maximum operating pressure 4569 SI (5 bar) ) Maximum flow 8.45 GM (2 L/min) H//D 585/97 + H//D

More information

Pressure relief valve, direct operated

Pressure relief valve, direct operated ressure relief valve, direct operated R 25402/05.0 Replaces: 10.05 /1 ype DBD Nominal sizes to 0 Component series 1X Maximum operating pressure 0 bar Maximum flow 0 l/min H5585 Overview of contents Contents

More information

Pressure-Relief Cartridge Valve, Size 4

Pressure-Relief Cartridge Valve, Size 4 Pressure-Relief Cartridge Valve, Size 4 Q max = 30 l/min, p max = 420 bar Seated design, direct acting, with mechanical operation Compact construction for cavity type AL 3/4-16 UNF High flow rates 7 pressure

More information

INVERS. Solenoid coil 24VDC 12 VDC Exm Exd Explosion protection marking:

INVERS. Solenoid coil 24VDC 12 VDC Exm Exd Explosion protection marking: direct operated INVERSE function available Q max = 2 l/min p max = bar INVERS Description EPDB The direct operated proportional pressure relief valve is built as a slip-in cartridge fitted in a connecting

More information

E 094 E 103 E 143 Tank top mounting Connection up to G1 / -16 SAE Nominal flow rate up to 135 l/min / 35.7 gpm

E 094 E 103 E 143 Tank top mounting Connection up to G1 / -16 SAE Nominal flow rate up to 135 l/min / 35.7 gpm Return Filters E 9 E E Tank top mounting Connection up to G / -6 SAE Nominal flow rate up to 5 l/min / 5.7 gpm Description Application In the return line circuits of hydraulic systems. Performance features

More information

Components for air preparation and pressure adjustment. OUT port position ( ) connected Rear side. of IN port. Air tank. directly.

Components for air preparation and pressure adjustment. OUT port position ( ) connected Rear side. of IN port. Air tank. directly. Components preparation and pressure adjustment ABP Overview ABP is a component that enables boosting by s only up to twice primary pressure (.0MPa max.) in combination with using air tank but not using

More information

220 Mobile Piston Pump Catalog Design Code A AEC028

220 Mobile Piston Pump Catalog Design Code A AEC028 220 Mobile Piston Pump Catalog Design Code A AEC028 Introduction 220 Series Piston Pump Eaton s new 220 Series piston pump signifies a step change in the generation of hydraulic power. Utilizing the latest

More information

ASM. Asynchronous Spindle Motors. SEM Limited Faraday Way Orpington, Kent BR5 3QT United Kingdom

ASM. Asynchronous Spindle Motors. SEM Limited Faraday Way Orpington, Kent BR5 3QT United Kingdom NE ASM Asynchronous Spindle Motors SEM Limited Faraday Way Orpington, Kent BR 3QT United Kingdom Tel: +44 ()189 8847 Fax: +44 ()189 884884 Email: sales@sem.co.uk Web: www.sem.co.uk Version 4 August 2 Asynchronous

More information

L6090 (LC04M-CBL) - L6095 (LC04M-CBD)

L6090 (LC04M-CBL) - L6095 (LC04M-CBD) or 3 way pressure compensated flow regulators L69 (LC4M-CBL) - L695 (LC4M-CBD) RE 1833-4 Edition:.16 Replaces: 7.1 Size 4 Series Maximum operating pressure 31 bar (45 psi) Maximum flow (-way) 1 l/min (3.

More information

Micro grippers HGPM/HGWM

Micro grippers HGPM/HGWM HGPM/HGWM Miniaturised and optimised for assembly tasks Versatile 2004/10 Subject to change Products 2004/2005 1 / 1 HGPM/HGWM Key features HGWM HGPM 1 2 3 4 1 2 3 4 System product for handling and assembly

More information

RE / Meter out pressure compensator Sandwich plate design Type SCA... /Series 2X. Description of function, Section 1/6. Replaces: 09.

RE / Meter out pressure compensator Sandwich plate design Type SCA... /Series 2X. Description of function, Section 1/6. Replaces: 09. Meter out pressure compensator Sandwich plate design Type SCA... /Series X Sizes 6, 5 up to 35 bar up to 35 L/min RE 9 47/.96 RE 9 47/.96 Replaces: 9.87 Sandwich plate design Load compensation in lines

More information

Pressure relief valve, direct operated. Type DBD. Features. Contents. RE Edition: Replaces:

Pressure relief valve, direct operated. Type DBD. Features. Contents. RE Edition: Replaces: Pressure relief valve, direct operated Type DBD R 2542 dition: 21-7 Replaces: 214-8 Size 3 Component series 1X Maximum operating pressure 3bar [915 psi] Maximum flow 33 l/min [87 US gpm] H5585 Features

More information

Leak-Free Load-Control Valve SAE ½ psi flange

Leak-Free Load-Control Valve SAE ½ psi flange Leak-Free Load-Control Valve SE ½ - 6000 psi flange Q max = 150 l/min [40 gpm], p max = 420 bar [6000 psi] leak-proof, two-stage hydraulic, SE-flange design 12--S... 1 Description Two-stage load-control

More information

Pressure relief valve, direct operated Type DBD

Pressure relief valve, direct operated Type DBD Industrial Hydraulics Electric Drives and Controls Linear Motion and Assembly echnologies neumatics Service Automation Mobile Hydraulics RE 25 402/06.02 Replaces: 03.98 Material No.: 00772632a ressure

More information

SIHI LPH-X - Liquid Ring Compressors

SIHI LPH-X - Liquid Ring Compressors - Liquid Ring Compressors LPH 50523 LPH 60527 Pressure range: Suction volume range: 0.2 to 1.5 bar 260 to 780 m³/h CONSTRUCTION Sterling SIHI liquid ring compressors are displacement compressors with a

More information

Hand pump type CH. Product documentation. 300 bar 8.3 cm 3 /stroke. Operating pressure p max : Displacement volume V max stroke :

Hand pump type CH. Product documentation. 300 bar 8.3 cm 3 /stroke. Operating pressure p max : Displacement volume V max stroke : Hand pump type CH Product documentation Operating pressure p max : Displacement volume V max stroke : 300 bar 8.3 cm 3 /stroke D 7147 CH 04-2018-1.1 by HAWE Hydraulik SE. The reproduction and distribution

More information