Technical Specifications

Transcription

1 V200P Pneumatic Positioner Input range: 3-5 PSI kpa Supply pressure: 45 PSI < MPa Linearity error: <0.7 f.s <0.4 f.s. Repeatability: <0.3 f.s. Pressure Gain: 240: 00: 00: Air Connections: -40º to 85º Fahrenheit ¼ NPT or G Threads Weight 3.5 lbs.6 kg

2 V200E-FF Electropneumatic Fail Freeze Positioner Input range: Supply pressure: Linearity error: Repeatability: 4-20mA Load presents 6 volts (+/-0.5V) constant voltage drop to the current source PSI <.2% f.s. <0.9% f.s. <0.8% f.s. Pressure Gain: 240: 00: 00: acc.to ISA S75.3 Positioner: Supply pressure effect: negligible Loop voltage drop: +/-0.5 V Reverse protection: 25 ma Over current protection: 25 ma Fail Freeze Mode: Input signal fail below 2 ma +/-0.5 ma Fail Freeze Drift Rate:.02% in 30 seconds (mid range) Air Connections: Cable entry: -20º to 58º Fahrenheit -20º to 70º Celsius ¼ NPT or G Threads ½ NPT optional 30mm square Connector DIN Weight 5.4 lbs.

3 V200E-EX-Electropneumatic Explosion Proof Positioner Input range: 4-20mA (R<260 ohms) Supply pressure: PSI 0.2-MPa Linearity error: <0.8% f.s. <0.5% f.s. Repeatability: <0.% f.s. Pressure Gain: 240: 00: 00: acc.to ISA S75.3 Positioner: º to 85º Fahrenheit Cable entry: ½ NPT or M20x.5 or PG 3.5 Ingress & corrosion protection: Nema 4X and IP 65 Weight 5.4 lbs Approvals Atex/Cenelec Intrinsically safe: EEX ia IIB T4 Flameproof: EEx d IIB +H2 T4 British Standard (NI) Non incendive: Ex N II T6 for Zone 2 FM Intrinsically safe: CL I-II-III/Div /Grp CSA Intrinsically safe: CL I/Div /Grp CD CL II/Div /Grp EFG CL III CL I/Div 2/Grp BCD CL II/Div /Grp EFG Explosion proof: CL I/Div /Grp BCD CL II/Div /Grp EFG GOST EEx ia or EEx d (Russia/Ukraine)

4 V200E-GA-Electropneumatic Explosion Proof Positioner-Gas Approved Input range: Supply pressure: Linearity error: Repeatability: Loop Load 4-20mA PSI <.0% f.s. <0.5% f.s. <0.5% f.s ma Pressure Gain: 240: 00: 00: acc.to ISA S to 60 Fahrenheit -40 to 7 Celsius Cable entry: ½ NPT or M20x.5 or PG 3.5 Weight 5.5 lbs Approvals FM CSA Instrinsically Safe Cl, Div & 2, Gps BCD Cl II Dive, Gps EFG Cl III Div fibers Temp Code T4 Explosion Proof Cl I, Div & 2, Gps B,C,D Dust Ignition Proof Cl II & III, Div, Gps EFG

5 V200E 0-0 VDC Electropneumatic Positioner Input range: Supply pressure: Linearity error: Repeatability: Pressure Gain: Acc. To ISA S VDC PSI <.0% f.s. <0.5% f.s. <0.5% f.s. 750 Pout/Pin 49% Pout/Pin Pressure Gain: 300: 00: 00: acc.to ISA S to 60 Fahrenheit -40 to 7 Celsius Cable entry: ½ NPT or M20x.5 or PG 3.5 -Positioner Epoxy-IP Transducer Ip Converter 3 wire VDC Input/power 0-0 VDC Signal Frequency response Vibration effect -3 db@ 5 Hz Less than +% of Span under inches constant displacement Gs. Weight 3.8 lbs.7 kg

6 V200E-IS Electropneumatic Positioner Input range: 4-20mA (Ri<70 ohms) Supply pressure: PSI MPa Linearity error: <.0% f.s. <0.6% f.s. Repeatability: <0.5% f.s. Pressure Gain: 240: 00: 00: acc.to ISA S º to 85º Fahrenheit Cable entry: ½ NPT or M20x.5 or PG 3.5 Weight 3.8 lbs.7 kg IS Approvals Atex/Cenelec EEx ia IIC T4-T6 FM/CSA CL I Div Grp ABCD CL I Div 2 Grp ABCD

7 V200P EHT (Extra High Temp) Pneumatic Positioner Available in pneumatic only. Input range: 3-5 PSI kpa Supply pressure: 45 PSI < MPa Linearity error: <.0 f.s <0.5 f.s. Repeatability: <0.4 f.s. Pressure Gain: 240: 00: 00: acc.to ISA S to 325 Fahrenheit -40 to 63 Celsius Temperature Effect: 325F Span 325F The above is based on calibrating at ambient temperature and the unit subjected to 325F. Air Connections: ¼ NPT or G Threads Nickel Plated-Aluminum Weight 3.5 lbs.6 kg

8 V200 Nickel V200 P, E, IS Units with Nickel Coating V200 P V200 E V200E-IS* Input range: 3-5 PSI 4-20mA (Ri<230 ohms) 4-20 ma (Ri<70 ohms) Supply pressure: 45 PSI PSI PSI Linearity error: <0.7% f.s. <.0% f.s. <.0% f.s. <0.6% f.s. <0.6% f.s. Repeatability: <0.5% f.s. <0.5% f.s. Pressure Gain: 240: 00: 00: acc.to ISA S º to 85º Fahrenheit Cable entry: ½ NPT or M20x.5 or PG 3.5 Nickel Weight 3.8 lbs.7 kg *IS Approvals Atex/Cenelec EEx ia IIC T4-T6 FM/CSA CL I Div Grp ABCD CL I Div 2 Grp ABCD

9 V200 Tufram V200 P, E, IS Units with Tufram Coating V200 P V200 E V200E-IS* Input range: 3-5 PSI 4-20mA (Ri<230 ohms) 4-20 ma (Ri<70 ohms) Supply pressure: 45 PSI PSI PSI Linearity error: <0.7% f.s. <.0% f.s. <.0% f.s. <0.6% f.s. <0.6% f.s. Repeatability: <0.5% f.s. <0.5% f.s. Pressure Gain: 240: 00: 00: acc.to ISA S º to 85º Fahrenheit Cable entry: ½ NPT or M20x.5 or PG 3.5 Tufram Weight 3.8 lbs.7 kg *IS Approvals Atex/Cenelec EEx ia IIC T4-T6 FM/CSA CL I Div Grp ABCD CL I Div 2 Grp ABCD