SECTION 5 CONVEY LINE & CONVEY LINE ACCESSORIES Tubing and Pipe
|
|
|
- Gervase Jeffrey Sparks
- 5 years ago
- Views:
Transcription
1 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES Tubing and Pipe TUING ND PIPE STRIGHT LENGTHS vailable in cut-to-length; 20-ft to 40-ft random lengths vailable in: galvanized steel MTERIL FORM ITEM NUMER DESRIPTION LLOY 6063 STM -221 PIPE ND TUING MTERIL SPEIFITIONS LUMINUM RON STINLESS GLVNIZED STRIGHTS STM T-6 ENDS STM T-1 PIPE STM -53 Seamless, welded black and galvanized steel pipe TUE STM -513 Electric resistance welded carbon and alloy steel for use as mechanical tubing PIPE STM -312 Seamless and welded stainless steel pipe intended for high-temperature and general corrosive service. Twenty-four grades available, including 304, 316, 304L and 316L TUE STM -249 Stainless steel tubing for general corrosion resisting and low- or high-temperature service OTED PIPE STM -53 Galvanized coated pipe OTED TUE STM -513 Galvanized coated tube TUE STM Galvanized tube S5-9 For Ordering and Pricing Information, all Toll Free
2 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES Tubing and Pipe INTERNL-SPIRL-GROOVED PIPE ND TUE Grooved internal surfaces disrupt boundry layer of flow, encouraging product tumble rather than sliding flow and reducing angel hair in plastic pellets. vailable in aluminum or stainless steel tube and pipe vailable 2-inch O.D. through 8-inch I.P.S. Sandblast and shot peened treatment also available Maximum length available is 20 feet DIRETIONL SHOT-PEENED PIPE Directional Shot-Peening the interior of a pipe or tube is performed to help reduce fines and streamers when conveying plastic pellets or resins in a Dilute Phase conveying process. fter the interior of a pipe receives a shot-peening treatment the interior would have a dimpled roughness, this causes the air used in the convey process to create a turbulence in the line, specifically along the inner wall. This turbulence will reduce the product being conveyed from sliding down the wall of the convey line thus reducing Fines, Snake Skins and Streamers. Note: Shot-Peen treated pipe should only be used in Dilute Phase conveying systems, and is not recommended for Dense Phase convey systems. For Ordering and Pricing Information, all Toll Free S5-10
3 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES Elbows Long and Short Radius STNDRD SHORT ND LONG RDIUS ELOWS Pipe and tube bends up to 180 degrees, at a wide variety of bend radii eramic lined for abrasive applications vailable in: galvanized steel Special construction available upon request The Service enter has an extensive inventory of tube bends available for three-day shipment. Most popular bend sizes are stocked in carbon-steel, aluminim and stainless-steel materials. OD Outside Diameter ST Tangent D end ngle in Degrees Face to End enterline to End Setback LR enterline Radius Inside Radius Outside Radius ST Tangent OD TUE SIZE PIPE SIZE DIMETER ELOW END VILILITY (MESUREMENTS IN INHES) STNDRD TNGENT (ST) OMMON ENTERLINE RDII (LR) / / / / / / / / / / / / / / / / / tube, 6 pipe / / / tube, 7 pipe / / / tube, 8 pipe / / / FOR 90 ENDS Face-to-End = LR + Tangent + (1/2) OD enterline-to-end = LR + Tangent Setback = LR (enterline Radius) FOR OTHER ENDS Setback = LR x (Tangent) 1/2 bend angle enterline-to-end = Setback + Tangent NOTES Order ends Stat: by outside diameter, wall thickness, alloy, degree of bend, centerline radius and tangent Wall Thickness: 16-ga. (0.063), 14-ga. (0.083) and 11-ga. (0.120) tubing. Schedules 5, 10 and 40 pipe. Other wall thicknesses available on request. MTERIL LUMINUM STINLESS RON GLVNIZED METL SPEIFITION PIPE 6063-T1 Extruded T304 STM 312 STM 53 Galv. 53 TUING 6063-T1 Extruded T304 STM 249 STM 513 Galv. 513 S5-11 For Ordering and Pricing Information, all Toll Free
4 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES onvey Line Sight Glasses ONVEY LINE SIGHT GLSSES llows viewing of material flow Smooth, straight-through interior ir-tight seal Viewing area available in: acrylic Pyrex Pipe or tube available in: Permanently attached grounding strip eliminates build up of static electricity TUE OR PIPE INSERTED IN LER RYLI LER RYLI INSERTED IN PIPE PRT NUMER TUE WITH LUMINUM ENDS SIZE IN INHES OVERLL O.D. TUE O.D. TUE I.D. INSIDE DIMETER 1-1/2-OD OD OD /4-OD /2-OD /2-OD OD OD /2-OD /2-OD OD OD /2-OD /2-OD OD OD OD PRT NUMER PIPE WITH ENDS SIZE IN INHES OVERLL O.D. TUE O.D. TUE I.D. INSIDE DIMETER SG-2-IPS SG-2-1/2-IPS PRT NUMER PIPE WITH LUMINUM ENDS SIZE IN INHES OVERLL O.D. TUE O.D. TUE I.D. INSIDE DIMETER SG-2-P SG-2-1/2-P PRT NUMER MTERIL SPEIFITION LUMINUM TUING 6063-T1 and 6063-T6 SIGHT GLSS ast acrylic resin PIPE Schedule 40 LUMINUM PIPE PIPE WITH ENDS SIZE IN INHES OVERLL O.D. GLSS O.D. Schedule 40 (Schedules 5 and 10 also available) TUE I.D. INSIDE DIMETER SG-3-IPS SG-3-1/2-IPS SG-4-IPS SG-5-IPS SG-6-IPS PRT NUMER PIPE WITH LUMINUM ENDS SIZE IN INHES OVERLL O.D. GLSS O.D. TUE I.D. INSIDE DIMETER SG-3-P SG-3-1/2-P SG-4-P SG-5-P SG-6-P LL ONVEY LINE SIGHT GLSSES For Ordering and Pricing Information, all Toll Free S5-12
5 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES Wearback Elbows 90 WERK ELOWS Designed for abrasive applications. 1/4-inch PRODUT FETURES Long-radius design for minimal pressure loss with granular product Wear-through capable design retains product in hollow channel vailable in Schedules 40 and 80 vailable in standard or induction-hardened construction Note: Wearback Elbows will provide improved life expectancy over standard elbows without wearbacks. However, Smoot cannot make any specific guarantees regarding the wear life. HR / HR Outside Radius enterline Radius Pipe Tangent end ngle in Degrees (90 or 45 Standard) F G G OD E H E 3 inches Typical profile for sizes 1-1/2 to 8 Typical profile for sizes 10 and 12 PRT NUMER PIPE SIZE FORMED 90 ELOW WERK PRTS DIMENSIONS PIPE TNGENT HR / HR 90 PIPE LR HRF E F G H DIMETER HNNEL PIPE RDIUS WIDTH / / / not required 1-1/2 4-3/4 1-1/2 3/ /4 10-1/ not required 1-13/16 5-1/ / not required 2-1/2 5-1/ / not required 2-13/16 6-3/ / /8 18-5/ not required 3-11/16 7-1/ / /4 20-1/ not required 4-1/8 6-3/ / /4 25-1/ not required 4-13/16 7-3/ / /2 33-1/ /8 11-3/ /2 38-1/ / S5-13 For Ordering and Pricing Information, all Toll Free
6 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES Wearback Elbows 3 MX F 90 WERK ELOWS WITH REPLELE-HNNEL Designed for abrasive applications. Replace the wearback plate and not the entire elbow. HR / HR Outside Radius enterline Radius PRODUT FETURES Long-radius design for minimal pressure loss with granular product vailable with hollow, ceramic or cement-filled channels for maximum wear capability vailable in Schedules 40 and 80 vailable in standard or induction-hardened construction Note: Wearback Elbows will provide improved life expectancy over standard elbows without wearbacks. However, Smoot cannot make any specific guarantees regarding the wear life. D Pipe Tangent end ngle in Degrees (90 or 45 Standard) G I H OD E F ERMI FILL SSEMLY PRT NUMERS FORMED 90 ELOW DIMENSIONS QUNTITY EMENT PIPE OD TNGENT IR FILL HNNEL H I FILL PIPE D E F G SIDE END SSEMLY TNGENT LR SSEMLY SIZE (2 X OD) DIMETER NGLE PIPE OLTS OLTS / / / /2 7/16 3-5/ /4 10-1/ /16 5-1/ / /8 5/ /8 18-5/ /4 1-1/ /4 20-1/ /16 7/ /4 25-1/ /8 15/ / /2 33-1/ /16 7/ /2 38-1/ /4 1-5/ J TOTL OLTS For Ordering and Pricing Information, all Toll Free S5-14
7 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES Wear-Resistant, eramic-wrapper Elbows ERM-K WER-RESISTNT, ERMI-WRPPED ELOWS Designed to eliminate unwanted costs such as maintenance, loss of material and downtime. These elbows replace a conventional elbow and are manufactured to remain on a system much longer, thus reducing costs and raising production. The eram-ack Elbow has a jacket across the back of the core elbow which is approximately 1/2-inch of ceramic compound. This extremelyhard, ceramic jacket and core elbow is then wrapped with an exterior material to maintain the hoop strength. Once the core elbow has worn through, the abrasion is transferred to the ceramic outer jacket. The core also acts as a static conductor. Plain ends, flanges, and custom ends are available. PRODUT FETURES Elbow has a 1/4-inch ceramic compound jacket across the core elbow eramic compound has a Mohs hardness of 9+, second only to diamond (10 on the Mohs scale) eramic jacket and core elbow is wrapped with an exterior material to maintain hoop strength Easily replaces existing elbows vailable in any degree and standard LRs Pipe or tube available in: galvanized steel Various ends available upon request ERMI OMPOUND ERM-K ROSS SETION RDIUS OF ELOW REINFOREMENT TO MINTIN EXTERIOR HOOP STRENGTH INTERIOR SUSTRTE S5-15 For Ordering and Pricing Information, all Toll Free
8 SETION 5 ONVEY LINE & ONVEY LINE ESSORIES Standard and Special Welded Fabrications STNDRD ND SPEIL WELDED FRITIONS Pipe or tube available in: galvanized steel O.D. DIMETER T-JOINT DIMENSIONS IN INHES / D E O.D. DIMETER Y-JOINT DIMENSIONS IN INHES E = 30 E = 45 D D / LTERL JOINT DIMENSIONS IN INHES G O.D. DIMETER F = 30 F = 45 G H G H F H / For Ordering and Pricing Information, all Toll Free S5-16
INTERLOCKED METAL HOSE
INTERLOCKED METAL HOSE HOSE FUNDAMENTALS Penflex interlocked metal hoses are made for a variety of specialized industrial applications and are available in a wide range of metals, styles and sizes. Interlocked
Buttweld Fittings ANSI B16.9, ANSI B16.28, MSS-SP-43, MSS-SP-95, MSS-SP-97
uttweld Fittings NSI 16.9, NSI 16.28, SS-SP-43, SS-SP-95, SS-SP-97 90 LR ELOWS 45 LR ELOWS 180 LR ELOWS 90 SR ELOWS oncentric and eccentric reducers, equal and reducing tees, 45 and 90 elbows, buttweld
SO 9001 I ACCESSORIES
ISO 9001 ESSORIES ESSORIES INDEX Page In-Line Mounted Flow ontrol Valves 3 In-Line Mounted heck Valves 3 Quick Exhaust, heck and Shuttle Valves In-Line Ported Lockout Valves 5 Mufflers 6 Fittings 7-9 2
DUAL WALL ROUND DUCT AND FITTINGS CONSTRUCTION STANDARDS
ir istribution orporation ouble Wall ROUN U W ROUN UT N FITTINGS ONSTRUTION STNRS Outer Shell Positive Pressure Gauge selection for galvanized (STM 653). Fittings are manufactured with standing seam, welded
Material Handling Hose
Novaflex 5000 Slurry King Hose Pure Gum Liner Tough, versatile alternative to inflexible, cumbersome steel tubing. The easy handling and reusable quick-fastening flange system make installation a snap.
Groove Dimensions For Standard Wear Ring Widths
NYLON WER RING TEHNIL INFORMTION T E T X D X W W - YLINDER ORE - ROD DIMETER - MINIMUM ORE MINUS.253/.256 D - MXIMUM ROD DIMETER PLUS.253/.256 E - GROOVE WIDTH T - THIKNESS OF WER RING W - WIDTH OF WER
Air Distribution Corporation Spiral Duct and Fittings are manufactured in accordance with applicable SMACNA, ASHRAE and SPIDA standards.
ir istribution orporation Spiral uct and Fittings onstruction Standards ir istribution orporation Spiral uct and Fittings are manufactured in accordance with applicable SMN, SRE and SPI standards. Galvanized
TABLE 4 TABLE 5. Design Recommendations. for Conductive Elastomers. Fillers. Profiles
Design Recommendations for Conductive Elastomers Fillers Leader Tech Inc. is currently offering six different fillers that can be mixed with the polymers. These fillers are Pure Silver, Silver Plated Copper,
General Information Gravity roller conveyors are available in many sizes and configurations as shown on the following pages. There are many factors to consider when selecting a gravity conveyor. The following
KEYSTONE. A C E C O E n v i r o n m e n t a l C o m p a n y. Bulletin 10-B
KEYSTONE Filtration Solutions A C E C O E n v i r o n m e n t a l C o m p a n y Bulletin 10-B Standard Housings The 11N, 21N and 23N filter housings are tested and certified by NSF International under
Football Equipment. 5 9/16" Gooseneck Goalposts
5 9/16" Gooseneck Goalposts Football Equipment FB55CG 5 9/16" Gooseneck College Goalposts Applies also to FB55CG-SY and FB55CG-WT Goalposts shall meet all NCAA rules. Goalposts shall be of the single bent
SECTION BUTTERFLY VALVES
SECTION 15112 BUTTERFLY VALVES PART 1 GENERAL 1.01 SUMMARY A. All butterfly valves shall be of the tight closing, rubber seated type and fully comply with the latest revision of AWWA Standard C504, Class
For use in Natural Gas & Liquefied Petroleum Gas Applications
GasShield For use in Natural Gas & Liquefied Petroleum Gas Applications Streamline GasShield Coated Copper Tube comes coated with a yellow layer of seamless polyethylene. Commonly used with the distribution
Ford Service Saddles and Tapping Sleeves
Section AA 5/2001 Ford Service Saddles and Tapping Sleeves The Ford Meter Box Co., Inc. 775 Manchester Avenue, P.O. Box 443, Wabash, Indiana, USA 46992-0443 Telephone: 219/563-3171 FAX: 1-800-826-3487
ROTARY AIRLOCK FEEDERS
DRY BULK MATERIAL HANDLING ROTARY AIRLOCK FEEDERS CONCEPT TO COMPLETION STANDARD MODELS The selection of the correct rotary airlock and options is critical to maintain an efficient and reliable plant operation.
Your Global Partner for Heat Exchanger and Boiler Tubes
HELICAL HIGH AND EXTRUDED FINNED TUBE Product information guide INTRODUCTION In our brand new, purpose built facility we have installed three fin tube machines, engineered and manufactured with the most
Hoist Ring Forged Hoist Ring Machined Hoist Ring (Metric) Hoist Ring Swivel Shoulder Eyebolts JD Weld-On Alloy Lifting
Hoist Ring Forged........................... 94 Hoist Ring Machined........................ 95 Hoist Ring (Metric).......................... 96 Hoist Ring Swivel........................... 97 Shoulder
Material Handling Hose
Novaflex 5000 Slurry King Pure Gum Liner Tough, versatile alternative to inflexible, cumbersome steel tubing. The easy handling and reusable quick-fastening flange system make installation a snap. Absorbs
TUBE SIGN POST PRODUCTS
Western Canada TUBE Products Ltd. SIGN POST PRODUCTS Company Profile With over 100 years of experience on staff and the largest inventory in Western Canada, we have the ability to meet all your sign support
VERTICAL BLADDER TANK
Balanced Pressure Proportioning System Reliable Foam System Requiring Only Water Power Perfect For Tight Spaces UL Listed, ASME, National Board Registered Bladder-UL162 Approved, High Tensile Pressure
TAZGO DIVISION. Available Services: Shearing, Plate Burning, Saw Cutting, Drilling
TAZGO DIVISION STEEL~STAINLESS~ALUMINUM Beams ~ Channel ~ Flat bar ~ HR Rounds ~ CR Rounds Angle ~ Square Tube ~ Rectangle Tube Pipe~ DOM~ Plate~ HR sheets ~ CR sheets~ Galvanized Sheets ~ Cross Members
A COMPLETE LISTING OF OUR WASHERS BY INNER DIAMETER STARTS ON PAGE D32
A COMPLETE LISTING OF OUR WASHERS BY INNER DIAMETER STARTS ON PAGE D32 Component Flat Washers Component Flat Washers The Largest Selection in the World! Steel, Stainless Steel and Brass The standard Flatwasher
Tsubaki Sprocket Capabilities
Tsubaki Sprocket Capabilities Introduction to Made-to-Order Sprockets At Tsubaki, our commitment is to bring you the highest value in the industry today. Period. And as a full line supplier of power transmission
PN LINE. Technical remarks PN 11 PN 13 PN 14 PN 15 PN 17 PN 18 PN 20 PN 23 PN 25 PN 26 PN 27 PN 28 PN 29 PN 37 PN 38 PN 39 PN 40 PN 43 PN 10 8_9 10_12
PN LINE PN 11 PN 13 PN 14 PN 15 PN 17 PN 18 PN 20 PN 23 PN 25 PN 26 PN 27 PN 28 PN 29 PN 37 PN 38 PN 39 PN 40 PN 43 PN 10 Technical remarks PN 11 PN 13 PN 14 PN 15 PN 17 PN 18 PN 20 PN 23 PN 25 PN 26 PN
- Written price quotations are valid for 30 days from the date of the quote unless otherwise noted.
SPECIFICATIONS - All material is solid brass with a #8 mirror finish unless otherwise noted. - All material sold by length is priced in one foot increments. ORDERING PROCEDURE - Use a Purchase Order number.
WELL COMPLETION & PROTECTION. www. .com MINERAL EXPLORATION ENVIRONMENTAL GEOTECHNICAL GEOTHERMAL ROTARY SONIC HDD
WELL COMPLETION & PROTECTION MINERAL EXPLORATION ENVIRONMENTAL GEOTECHNICAL GEOTHERMAL ROTARY SONIC HDD www..com WELL COMPLETION & PROTECTION TABLE OF CONTENTS TABLE OF CONTENTS (FLUSHMOUNTS)... 2-5 MONITORING
Wheels lie at the heart of nearly every material handling
W HEELS lie at the heart of nearly every material handling system. Improperly specified or poor quality wheels can wreak havoc on the simplest task or a highly complicated system. Fast paced technology
SafidDampers. Class 1A & Class 1 Low Leakage Volume Control Damper ( Flange Type ) SPK Standard Construction. Description SPK
( Flange Type ) SPK 30 400 Standard Construction FRAME: 60mm x 30mm x.5mm (6 Ga.) galvanized steel formed channel for flange connection. BLADES: 00mm, 5mm and 50mm wide airfoil shaped blades extruded aluminum.
The Outer Seal is highly abrasion resistant and provides mechanical stiffness to the splice in order to better match the cable stiffness.
The Sealing Compound encapsulates the electrical splices, provides a strain relief for the conductors, acts as a water block, eliminates air voids which tend to act as pumps to draw in water during pressure
High Pressure Equipment Taper Seal Valves, Fittings and Tubing
igh quipment Taper Seal Valves, ittings and Tubing 0,000 and,000 psi service igh quipment Company has developed the Taper Seal line of products to assure safe and easy plumbing through,000 psi. These needle
PLATE TOP AND GRIPPER CHAINS
PLTE TOP ND GRIPPER CHINS Rexnord has a wide variety of Plate Top and Gripper chains. The roller chain based Plate Top is developed for greater ing capacity and permits even higher speeds and longer runs
ASYBCO 90 O ELBOW LONG RADIUS O.D. I.D.
90 O ELBOW LONG RADIUS Standard weight Extra strong Schedule 160 Double extra strong ASTM A-234 ASME / ANSI B16.9 Carbon and ferritic alloy steel Produced from X-rayed, stress-relieve welded pipe. Welds
SPIRAL PIPE - OVAL SINGLE WALL
SPIRAL PIPE - OVAL SINGLE WALL Duct Direct Pipe and Fittings are manufactured in accordance with 2005 SMACNA Duct Construction Standards (1995 SMACNA Standards on request) OVAL SUBMITTAL Oval Single Wall
HORIZONTAL BLADDER TANK
Balanced Pressure Proportioning System Reliable Foam System Requiring Only Water Power Perfect For Low Ceilings UL Listed, ASME, National Board Registered Bladder-UL162 Approved, High Tensile Pressure
Glass Steel, Inc. Fiberglass Composite Troughs
Glass Steel, Inc. Fiberglass Composite Troughs El Mira, CA Flat Bottom Curved Troughs Glass Steel, Inc. FIBERGLASS COMPOSITE TROUGHS Glass-Steel, Inc. manufactures a proprietary system of composite effluent
Guide for Evaluating Your Hose Assembly Supplier
Guide for Evaluating Your Hose Assembly Supplier Supplier Evaluation Checklist, and How to Clearly Define Application Requirements Safe, reliable hose assemblies require appropriate specification work
pvc well casing & drop pipe
C e r t a i nte e d pvc well casing & drop pipe P V C We l l P r o d u c t s Sure Fit PVC well casing and drop pipe have gained broad acceptance since their introduction almost 40 years ago. Today, due
Adapters and Tube Fittings Index
dapters and Tube Fittings Index lphabetical Index PRESSURE HOSE HIGH PRESSURE HOSE HOSE FITTINGS TUBE FITTINGS DESCRIPTION PGES DESCRIPTION PGES DESCRIPTION PGES DESCRIPTION PGES dapters 196 Braze and
A hose layline contains important information for specifying the replacement assembly: manufacturer, hose trade name, working pressure and hose ID.
CONTENTS Introduction Pressure Pressure Drop Temperature Rating Bend Radius Conclusion Additional Information SIDEBAR: Understanding Hydraulic Hose Reinforcement INTRODUCTION Hydraulic hose has a finite
TSuBAki SPROCKET SOLUTIONS. SproCkeTS For MAXiMuM performance
TSuBAki SPROCKET SOLUTIONS SproCkeTS For MAXiMuM performance 1 TSUBAKI Sprocket Solutions Made IN JAPAN Tsubakimoto Chain Co. based in Japan is the world s largest chain manufacturer with manufacturing
Tubular Aluminum Frames
Tubular Aluminum s Sefar offers rigid aluminum frames for screen-printing; textile, container, small and large graphics and membrane switches. These durable sturdy frames allow high tensions, good mesh
Manufacturing Processes and Products of Steel Pipes and Tubes in JFE Steel
JFE TECHNICAL REPORT No. 7 (Jan. 2006) Manufacturing Processes and Products of Steel Pipes and Tubes in JFE Steel MASAMURA Katsumi *1 NAGAHAMA Yutaka *2 Abstract: JFE Steel operates manufacturing facilities
Homestead Series 820 AWWA Butterfly Valves
Homestead Series 820 AWWA Butterfly Valves Dependable Valves for Water & Wastewater Service BODY: The ductile iron body meets or exceeds the design strength requirements of the AWWA C504 standards. Flange
Roughneck TM Mesh Slings
Roughneck TM Slings ROUGHNECK WIRE MESH SLINGS Widely used in metalworking shops and steel warehouses where loads are abrasive, hot or tend to cut web slings Features and Benefits Promotes Safety Steel
PSI Compakt - Special Seals
Pipeline Accessories PSI Compakt - Special Seals Compakt - special versions also with KTW/W270 for potable water General Information Selection Guide Order Submittal Sheet Installation Instruction 1 PSI
PLEASE NOTE: Pressures for 200mm (8ins) and 250mm (10ins) are based on the use of METALFLEX Braided Braid
METCONAB B-FLEX Stainless Steel Annular Convoluted Hose. A close pitch hose with a high degree of flexibility suitable for most applications and normally supplied. BRAID Single or double layers of Stainless
* SEE ANCHOR SCHEDULE SHEET 7
"-20 MLE PNELMTE W/ WINGNUT -1/2" O.C. "-20 X 1/2" MCHINE OLT & NUT -1/2" O.C 04/0/15 JH UPDTE TO 5TH EDITION (2014) FC 8/14/1 Y DTE SPCING ERROR OR MSONRY POWERS CLK-IN W/ "-20 SIDEWLK OLT -1/2" O.C.
Hoses and Lances 20,000 PSI
Jetstream provides a full arrangement of hoses and flex lances for ultra high pressure waterblasting. The hoses and lances are designed to be durable and reliable for any 20,000 psi application. A large
AWWA Pipe Flanges. AWWA C Standard Steel Hub Flanges Class D AWWA C Standard Steel Hub Flanges Class E AWWA C Flange Manufacturer
WW Pipe Flanges WW Flanges are commonly used in waterworks, wastewater, slurry, plant piping or other light duty applications generally requiring pressures of less than 300 psi. Pressure ratings for WW
Metric Hose End Fittings to Braided AQP Hose
ack to HOME Metric Hose End Fittings to raided QP Hose T Inc. offers a comprehensive line of Metric to -N hose ends and adaptors. luminum hose ends attach easily to popular -N braided hose and fit directly
4-63 T UBE FITTINGS TUBING P OLYURETHANE TUBING SERIES TU P RODUCTS FOR A LIST OF STOCKED PRODUCTS, PLEASE SEE THE CURRENT SMC PRICE LIST S TOCKED
T UBE FITTINGS 4-63 P OLYURETHANE TU Flexible tubing For general industrial air and water applicatons 20m and 100m coils 8 colour option Available in metric size (TU) and inch size (TIUB) CONTACT SMC FOR
tubepress press procedure
tubepress press procedure tubepress 15mm up to 35mm tubepress 15 mm up to 35 mm 1. The tube ends must be clean with no scratches or grooves. Remove end caps. Cut tube to length. 2. Deburr tube inside and
DuoSafe. DuoSafe Inch Systems. Larger sizes on request
pvc-u and pvc-c DuoSafe DuoSafe systems are manufactured from rigid PVC-U or rigid PVC-C, with containment pipe options including grey or clear PVC-U, PVC-C, ABS or Polyethylene. They are ideal for above
Sample C ylinde rs, Acce ssorie s, and O utage Tube s
www.swagelok.com Sample C ylinde rs, cce ssorie s, and O utage s Features Sizes from 10 to 3785 cm 3 (1 gal) Working pressures up to 5000 psig (344 bar) 304L and 316L stainless steel and alloy 400 2 Sample
Use equation for the cylindrical section and equation or for the ends.
Solution 13.1 See section 13.3.4, equations 13.7 to 13.18 Solution 13.2 Use equation 13.34. (a) rigid constant C = 0.43 (b) free to rotate, C = 0.56 Solution 13.3 See section 13.5.1 Use equation 13.39
Sprocket Selection Guidelines
Sprocket Selection Guidelines Table 1 Information Necessary to Order Sprockets 1. Chain Size Number, type, or drawing number of the chain to be used on the sprocket. (The suitability of a sprocket depends
IAPMO GUIDE CRITERIA FOR BALL VALVES IAPMO IGC PURPOSE
INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS IAPMO GUIDE CRITERIA FOR BALL VALVES IAPMO IGC 157-20067 1 PURPOSE 1.1 The purpose of this standard is to establish an acceptable standard
MATERIALS FOR PLUMBING SYSTEMS FITTING AND INSTALLATION GUIDE
MATERIALS FOR PLUMBING SYSTEMS FITTING AND INSTALLATION GUIDE THINK GLOBALLY, ACT LOCALLY CONTENTS Propex DZR fittings and pex 2 Why depend on Propex hot and cold piping system 3 Cross linked polyethylene
AN Wireless Tower Assembly Instructions
N Wireless Tower ssembly Instructions RED THOROUGHLY EFORE SSEMLY ND ERETION Thank you for your purchase of an N Wireless Self Supporting Tower. N Wireless Towers are designed and fabricated to be high-strength,
Galvanized Rigid Conduit
Galvanized Rigid Conduit Conforms To: C80.1 - UL 6 ANSI C-80.1 UL Min. WGT. Per 100 Feet in LBS. INCL. CP. O.D. I.D. Thickness Threads Per Inch Feet Per Lift Color Code Thread Protector 1/2" 79.840.632.104
Nominal Wall Thickness Steel Only in. (mm) Outside Diameter With PVC in. (mm)
PVC-Coated Conduit The ultimate in corrosion protection! OCAL-BLUE Conduit Hot-dip galvanized steel or aluminum conduit. Nominal.00 ( mils) blue urethane coating on interior. Hot-dipped galvanized threads
Recommended applicable tubing. Specifications. Operating vacuum pressure. 20 C to 80 C Threads. Principal parts material
Series K Clean one-touch fittings For blowing Recommended applicable olyolefin: Series T Tubing material Soft polyolefin: Series TS Tubing O.D. ø, ø, ø, ø, ø olyurethane Series TU, Nylon Series T, and
PREDL head-office and production-plants
FRANCHISING by PREDL head-office and production-plants PREDL GmbH Germany PREDL AUSTRIA Ges. mbh AUSTRIA PREDL GmbH President: About us: Manfred Predl Places of production: PREDL Bönitz/ Germany PREDL
MSC Guidelines for Refrigeration Machinery
Procedure Number E1-32 Revision Date: 07/27/10 S. J. Kelly, CDR, Chief of Engineering Division References: a. 46 CFR Part 56.50-105 Low Temperature Piping b. 46 CFR Part 58.20 Refrigeration Machinery c.
DREDGING & MINING MEDIUM DUTY ABRASIVES HANDLING HOSE
MEDIUM DUTY ABRASIVES HANDLING HOSE A16, A17, A18, A25, A32, A39 Hand-built hard wall suction hose. Animal feeds, grains, flours, powders, cement, sand, dry waste, rubble. 51mm (2 ) to 254mm (10 ) 12 metres.
300lb MALLEABLE FITTINGS
NIPPLES & FITTINGS MLLEBLE FITTINGS MLLEBLE FITTINGS MLLEBLE FITTINGS ISO 9002 - CERTIFICTE OF QULITY - UL/ LISTED ND PPROVED T 300 PSI Our quality fittings are made with care and attention to detail.
LiftAlloy Chain Slings
CHAIN SLING BASICS Slings Lift-All chain slings meet or exceed all OSHA, ASME B30.9 and NACM standards and regulations. chain slings, available in 80 for 7/8"- /4" and 00 for 7/32"-3/4", are recommended
Heavy Equipment Technician Rigging
1. What is SWL? a. Single weight of load b. Second weakest location c. Working load limit Heavy Equipment Technician IP Red Seal Practice Exam d. Abbreviation for swivel Heavy Equipment Technician Rigging
Terminology. 2 MESH WIRE CLOTH (count from center to center of wires) 1/2 INCH OPENING WIRE CLOTH (clear space between wires)
CALENDERING - A rolling operation which flattens the knuckles of wire cloth giving it a smoother surface. CRIMP - Undulations in warp and fill wires which hold each other in place. FILL WIRE - aka SHUTE
Services. Fire Sleeve. by Carol and Brian Carpenter
Fire Sleeve by Carol and Brian Carpenter During our maintenance training courses, the subject of fire sleeve comes up on a regular basis. What is fire sleeve? Why should I use it? When do I need it? This
BUTTERFLY VALVES. Toll Free (877) - ICFLUID -2-
BUTTERFLY VALVES 1. General HyrdoWer is a globally recognized manufacturer of power unit accessories. They have become specialists in the design of Butterfly Valves and Hydraulic Compensators. The shut
The Duopex Gas. to make every job quick and easy. it provides a revolutionary alternative for the professional plumber and 02_DUOPEX GAS GAS MANUAL
duopex gas manual The Duopex Gas pipe and fitting system is designed to make every job quick and easy. it provides a revolutionary alternative for the professional plumber and gasfitter. 02_DUOPEX GAS
Saf-T Vent EZ Seal Plus
Technical and Dimensional Data Saf-T Vent EZ Seal Plus Single Wall L 29-4 Stainless Steel Special Gas Vent Tested and Listed to UL 1738/UL S636 by Underwriters Laboratories, Inc 5030 orporate Exchange
Protecting your punching tool investment. Application-related problems and solutions
Protecting your punching tool investment Application-related problems and solutions Article reprinted with permission from the May 2000 issue of The FABRICATOR. By Nick Tarkany Economic shortcuts in the
Series 8500 Expansion Compensators. Catalog 674H
Series 8500 Expansion Compensators Catalog 674H 500 Laminated Bellows Expansion J Series 8500 on Joints Expansion Compensators Sizes 3/4" through 4" Threaded, welded, flanged and grooved steel pipe joints
Flexible Metal Hose Products
Flexible Metal Hose Products Specialty Flexible Hose Solutions of Stainless Steel The AEROCOM Advantage Aerocom offers engineered solutions that address specific flexible piping challenges such as vibration,
HDX HDAR HDXP HDBT HDPV HDSE
HD S E R I E S The Meyer Heavy-Duty Series airlock valves provide maximum versatility in the most severe applications. Each model offers an engineered cost effective solution to the customers needs. These
TECHNICAL BULLETIN PINPOINT CONDUIT COUPLING AND SPLICING RECOMMENDATIONS
TECHNICAL BULLETIN PINPOINT CONDUIT COUPLING AND SPLICING RECOMMENDATIONS CONTENTS: 1.0 General Information 2.0 Preparation and Splicing of PinPoint Wire 3.0 PinPoint Direct Bury Splice Kit Specifications
Cryogenic Liquid Ultimate Liquid Cylinder Hose
Cryogenic Liquid Ultimate Liquid Cylinder Hose Flexible Components brand liquid cylinder hose is considered the highest quality liquid cylinder hose on the market. It effectively transfers cryogenic liquids
High Pressure Equipment Medium Pressure Valves, Fittings and Tubing
igh Pressure quipment Medium Pressure Valves, ittings and Tubing service igh Pressure quipment Company has developed a line of Medium Pressure products to assure safe and easy plumbing through. These needle
Installation Operation Maintenance
682 Seal Cooler New generation seal cooler to meet and exceed the seal cooler requirements stated in the 4th Edition of API Standard 682 Installation Operation Maintenance Experience In Motion Description
High Pressure Equipment Medium Pressure Valves, Fittings and Tubing
igh Pressure quipment Medium Pressure Valves, ittings and Tubing service igh Pressure quipment Company has developed a line of Medium Pressure products to assure safe and easy plumbing through. These needle
Made in U.S.A. Narrow-U Bike Rack Heavy Duty Submittal Sheet. Materials: Finishes: Mount Options: Setbacks:
Submittal Sheet Materials: 2 Schedule 40 Steel Pipe (2.375 OD) Finishes: Galvanized An after fabrication hot dipped galvanized finish is available Powder Coat Our powder coat finish assures a high level
HDPE. Dredging Pipeline
HDPE Dredging Pipeline R Ace Flowtech Co., Ltd Office address: No.2, 2-1601, Rongyuan Road, Huayuan Industrial Park, Tianjin Binhai Hi- Tech Area, Tianjin City, China, 300384 Factory address: No.51 Lutai
Aquor House Hydrant V2
Aquor House Hydrant V2 IN-WALL OUTDOOR FAUCET SYSTEM FLUSH-MOUNT QUICK-CONNECT SELF-DRAINING ANTI-SIPHON NON-FREEZE VBH-SERIES AQUOR HOUSE HYDRANT V2: WALL HYDRANT / FREEZELESS SILLCOCK Freezeless sillcock
Dynamic Cone Penetrometer SL970. Impact Test Equipment Ltd & User Guide. User Guide
Dynamic Cone Penetrometer SL970 Impact Test Equipment Ltd www.impact-test.co.uk & www.impact-test.com User Guide User Guide Impact Test Equipment Ltd. Building 21 Stevenston Ind. Est. Stevenston Ayrshire
10.2. Basketball Single Post System
Basketball Basketball Single Post System The basketball single post is made from special aluminium profiles. The structure is supported by one post in the ground. The post measures a cross section of 120
M A B MAB INFLATABLE GASKET SLIDE VALVES SERIES TSV FOR POWDERED AND GRANULAR SOLID MATERIALS
Automatic slide valves type TSV-150 with inflatable sealing system. The range of TSV slide valves supplied by MAB can always close against a head of flowing solids. The TSV series of inflatable gasket
Installation and Operating Instructions for Automotive Winch Synthetic Rope
Installation and Operating Instructions for Automotive Winch Synthetic Rope 2 1 Synthetic Rope Kit Parts List Part No. 251262 1. Rope Assembly (3/8 x 100 ) 2. Hook Strap WARNING: A minimum of EIGHT wraps
12 Impeller Replacement
144 Impeller Replacement INTRODUCTION Jabsco The Original Impeller Jabsco Flexible Impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general
Pac West Supply LLC Gorilla Guard Ladder Cage Enclosure Installation Guide
Installation Guide www.gorillaguardonline.com Front Hoop Clamp Slide Top Vertical Bar Rear Hoop Clamp Bottom Vertical Bar 3/8 Galv Carriage Bolt Handrail Clamp Pac West Supply Step 1-Installation of Bottom
OPTIONS. Mounting ACCESSORIES FLEXAC.CLIP FLEXAC.EC FLEXAC.P6 FLEXAC.4.C04 FLEXAC.4.C10 PERFORMANCE
FLEX 4 FLEX features driver-less LE technology R9 Values of 60+ Optically clear thermoplastic coating rated for IP65, interior or exterior This product can run up to 100 ft from a single feed with uniform
Precision Duct Systems 4570 Commerce Cir SW Atlanta, GA Phone (404)
Project Name: Engineer: Contractor: Section Number: Date Submitted: Date Approved: Pressure Class: Material Type: Connections: 2005 Up to 10 wg 1995 2 wg pos 1995 4 wg pos 1995 10 wg 2005 neg WG: 1995
OVERVIEW pg 3. Major Points to Consider pg 3 Minor Points to Consider pg 3. INSTRUCTIONS pg 4
TABLE OF CONTENTS OVERVIEW pg 3 Major Points to Consider pg 3 Minor Points to Consider pg 3 INSTRUCTIONS pg 4 How Does Nordic Freeze Work pg 4 How Long Will the Ice Plug Take to Form pg 4 How Do I Know
Corrugated Hose Loop Calculations
Corrugated Hose Loop Calculations The loop installation is one of the most common application for metal hoses. It allows the flexible hose assembly to work properly. Care must always be exercised to ensure
Body - May vary in shape, body beads may be present, and is constructed of electrolytic tinplate (ETP).
2 1 2. CAN TERMINOLOGY Any discussion or description of can defects requires standard terminology relating to the can components (end, body, double seam). The terminology required to describe these components
CERTIFICATE OF COMPLIANCE FOR RADIOACTIVE MATERIAL PACKAGES
9319 1 71-9319 USA/9319/B(U)F-96 1 OF 6 2. PREAMBLE a. This certificate is issued to certify that the package (packaging and contents) described in Item 5 below meets the applicable safety standards set
TORO TITAN TINES CATALOG 2013
TORO TITAN TINES CATALOG 2013 PLAN YOUR AERATION SCHEDULE TODAY ORDER YOUR TINES FROM YOUR LOCAL TORO DISTRIBUTOR TODAY TO MAKE SURE YOU'RE READY FOR YOUR AERATION SCHEDULE JAN FEB MAR APR S M T W T F
CHAIN LINK FENCE GATE
WALCOOM Walcoom Corporation CHAIN LINK FENCE GATE Chain link fence gate is a versatile product in many aspects, here, Walcoom provides buyers with sufficient strength and durability chain link fence gate
CHECK-VALVES Automatically Position Themselves by the Natural Forces of the Conveying Air. A PNEUMATIC CONVEYING SYSTEM PATENT #: 5,160,222
PATENT #: 5,160,222 PHONE: (913)677-5777 FAX: (913)677-067 E-Mail : techair@techairinc.com www.techairinc.com CHECK-KLEEN DIVERTER A PNEUMATIC CONVEYING SYSTEM FLAP-CHECKS exposed to product air stream