S A X O N A U T O M AT I C

Transcription

1

2

3 SAXON AUTOMATIC

4

5 CONTENTS International Warranty Watch Specification Watch Features Operating Instructions Crown Positions Manual Winding Changing the Time Changing the Date Adjusting Straps & Bracelets Water Resistance Care

6 INTERNATIONAL WARRANTY Automatic watches from Larsson & Jennings are guaranteed for 5 years from date of purchase. The watch movement, hands and dial are the only components covered during this warranty period. These covered components will be repaired or replaced free of charge if proven to be defective in material or workmanship under normal use. Please retain your International Warranty card, which can be found inside the box, to serve as proof of purchase. 02

7 INTERNATIONAL WARRANTY The warranty does not cover the following: Damages, and/or malfunctioning of the watch after the terms of warranty. Damages, and/or malfunctioning of the watch, caused by unauthorised persons or its representatives. Water damage. The strap, crystal sapphire glass, crown or buckle Postage, insurance and other non-repair expenses are excluded from warranty and are the customer s liability. 03

8 WATCH SPECIFICATION 39mm 9.85mm 35mm STHLM / LDN SWISS MADE 20mm 04

9 WATCH SPECIFICATION Watch Movement Case Back Display Glass Water Resistant Case Diameter Case Thickness Dial Diameter Lug Width - Saxon Automatic - ETA 2892.A2 / 21 Jewels 4Hz / vph 42 hour static power reserve - Exhibition / Mineral Glass - Sapphire Crystal anti-reflective / anti-fingerprint - 10ATM - 39mm mm - 35mm - 20mm 05

10 WATCH FEATURES KEY SWISS MADE 1. Hours 2. Minutes 3. Sweeping Seconds 4. Date 5. Crown 06

11 OPERATING INSTRUCTIONS Automatic watch movements generate their own power from the activity of the wrist while wearing the watch. The watch holds a power reserve of 42 hours when fully wound - this power reserve will gradually diminish when the watch is not being worn. When the power reserve is depleted, the watch can be wound be hand. Please refer to MANUAL WINDING on page

12 CROWN POSITIONS SWISS MADE 08

13 CROWN POSITIONS Position 1 - Closed Position 2 - Open, for manual winding Position 3 - Date Change Position 4 - Time Change 09

14 MANUAL WINDING Clockwise SWISS MADE 10

15 MANUAL WINDING Unscrew crown to Position 2. When Power Reserve is depleted or the watch has stopped, wind the crown clockwise 5-10 times maximum. Stop winding when you feel some resistance, as over-winding may cause tension damage inside the movement. If the watch is running, manual winding is not necessary. Once you have wound your watch, return the crown to Position 1 by pushing and screwing the crown back against the case. Please ensure the crown is set back to the watch s operating position for full water resistance. 11

16 CHANGING THE TIME SWISS MADE 12

17 CHANGING THE TIME Unscrew crown and pull the crown out to Position 4. Adjust the time by turning in either direction. Once you have changed the time, return the crown to Position 1 by pushing and screwing the crown back against the case. Please ensure the crown is set back to the watch s operating position for full water resistance. 13

18 CHANGING THE DATE Clockwise SWISS MADE 14

19 CHANGING THE DATE Unscrew the crown and pull the crown out to Position 3. Turn the crown clockwise, going through the date numbers to reach the correct date. Resetting the date will be required at the end of months that are shorter than 31 days, due to the 31 date wheel. Once you have changed the date, return the crown to Position 1 by pushing and screwing the crown back against the case. N.B The date should not be set when the hour hand is between the hour markers of 10 o clock (pm) and 1 o clock (am) Please ensure the crown is set back to the watch s operating position for full water resistance. 15

20 ADJUSTING THE CLASP (Milanese clasp) Insert the strap tool into the clasp gap. Gently pull down until flat to release the full clasp movement. Adjust to suit the size of the wrist, and replace the clasp once comfortable. Please ensure the clasp is securely fastened to its original position before wearing. 16

21 ADJUSTING THE CLASP (Deployment clasp) For premium leather straps with deployment clasps: To adjust length: Lift bar with lion engraving and select strap hole for clasp pin to go through. Return bar to closed position. To open/close: Push buttons on either side of the clasp, pull the deployment away from the wrist until it unfolds. To secure, fold the deployment clasp back on itself and push closed until it clicks into place. 17

22 CHANGING THE STRAP Securely hold the watch head, identifying the areas to insert the watch strap tool provided with your new strap. 18

23 CHANGING THE STRAP Insert the watch tool between the lug and the strap, placing the end of the tool on the adjustable spring bar. Once in position, manoeuvre the tool down to release the pin from the lug, where the strap will detach. Before use, move the strap back and forth to ensure the pin is securely fastened into the lug. For straps/bracelets with bolt pins, the watch tool is not needed. Simply pull back the pin to release the strap. 19

24 CHANGING THE STRAP Note: If you do not have a strap tool, please contact our support team at: support@larssonandjennings.com For further instructions, please see: 20

25 REMOVING LINKS In order to remove links on a Larsson & Jennings watch with a linked bracelet it is highly recommended to go to a local jewellers who will be able to add or remove links to reach the desired size. Additional links and pins are provided inside the watch box. 21

26 WATER RESISTANCE The Saxon Automatic watch is water resistant to 10ATM. Larsson and Jennings recommends following these guidelines for acceptable usage for the ATM ratings of this watch: 10ATM: Activities such as showering, bathing, swimming in a pool and snorkelling are acceptable. The watch should not be worn whilst diving. Please rinse the watch with fresh water after exposure to a chlorinated pool, salt water, soap, etc. 22

27 WATER RESISTANCE Note: The ATM rating only refers to watch heads, and not the strap. Leather straps should avoid contact with water or very high humidity atmospheres. For more information on what our water resistance ratings mean, please visit 23

28 CARE The Saxon Automatic watch should not be exposed to heavy wear, abrasions or knocks. The watch contains a number of mechanical parts which can be damaged by excessive shocks to the watch. Hard metals, stones or aggregates will scratch the case. Whilst the sapphire crystal glass is extremely resilient, hard metals, stones or aggregates will scratch the case. In order to keep the watch in it s best condition, and to ensure its longest lifetime, it should be cleaned regularly and serviced at least every 5 years. Before cleaning your Automatic make sure the crown is fully closed and screwed down in Position 1. Use a soft 24

29 CARE brush and warm fresh water, and gently brush around the exterior casing. Finish by wiping dry with a soft cloth. If the watch comes into contact with salt water or abrasive chemicals, ensure you clean the watch thoroughly with fresh water as above. Use the Larsson & Jennings cleaning cloth provided to polish and clean surfaces of the watch. For metal straps we suggest using warm soapy water to clean the strap. If you require a deeper clean, ultrasonic jewellery cleaners are available at good jewellery stores. Leather straps are not water resistant, and will need to be changed every 1-3 years. 25

30 Thank you for your purchase from Larsson & Jennings

31 Made in Switzerland