On-Off switch. Selectable manual control for commissioning. Remote start input for control via an irrigation controller, or external sensor.

Transcription

1 SPEEDMAN VARIABLE SPEED PUMP SET VARIABLE SPEED PUMP SET PRODUCT DESCRIPTION Variable speed / constant pressure system consisting of a Davey VM vertical multistage pump with Speedman controller, VSD unit, pressure transducer, 24 litre pressure tank, inlet and discharge manifolds, isolating and non-return valves, all mounted on a stainless steel base. APPLICATIONS Pumping of clean, non-aggressive liquids, free of fibres in suspension, suitable for applications such as:- Agriculture & Turf Watering Commercial & Industrial Processes Pressure Boosting in Commercial buildings Water Supply Rural & Industrial Commercial High Pressure Washing & Water Treatment FEATURES & BENEFITS OPERATING LIMITS Provides constant pressure via variable speed control for single pumps up to 3kW. Simple dial adjustable set point to allow the operator to adjust the set point to suit individual applications. Incorporates high & low pressure shutdown protection with adjustable delay timers. High & low pressure settings automatically track set point changes for ease of adjustment. Automatic sensing of no flow condition via pressure boosting to protect the pump. LED display shows pump operation, status and fault conditions. Indicators include power on, pump running, VSD fault, high pressure and low pressure faults and no flow testing. On-Off switch. Selectable manual control for commissioning. Remote start input for control via an irrigation controller, or external sensor. Programmable output relays for external communications of fault conditions, lag pump or jockey pump operation. Capacities to Pressure heads to 11m 3 /hr (1833lpm) 16m Maximum suction pressure Refer pg 2 Liquid temperature range Power supply single phase Power supply three phase Pump Rotation o to +7 o C up to 2.2kW up to 3kW Anti-clockwise (top view)

2 MAXIMUM INLET PRESSURE MATERIALS OF CONSTRUCTION Model VM3-8 VM3-12 & above Up to VM5-1 VM5-12 & above Up to VM1-6 VM1-8 & above VM16-2 and VM16-3 VM16-4 & above VM32-2A VM32-3 to VM32-4 VM32-6 to VM32-1 VM32-12 VM65-2A VM65-2 to VM65-3 VM65-4A and VM65-5 Up to VM9-3A VM9-3 & above Maximum Inlet Pressure 6 bar 1 bar 1 bar 15 bar 6 bar 1 bar 6 bar 1 bar 3 bar 4 bar 1 bar 15 bar 4 bar 1 bar 15 bar 1 bar 15 bar PART Pump base Suction & discharge casing Motor support lantern Impellers Stages (casing) Outside sleeve Pump shaft Intermediate bearing Mechanical seal Orings (casing) Plugs (drainage & priming) Impeller neck rings MATERIAL Cast iron 34 stainless steel Cast iron 34 stainless steel 34 stainless steel 34 stainless steel 316L stainless steel Tungsten carbide Silicon carbide/carbon/epdm EPDM 316L stainless steel Teflon * Special version with 316L stainless steel & viton orings on request NOTE: 34 stainless steel, (Z6 CN 18.9) and 316L stainless steel (Z2 CND 17.12) are recommended materials that are highly resistant to corrosion. Suitable for pumping clean, clear non-viscous liquids, containing no fibres or solids. Maximum sand/silica concentration 4 g/m 3. MAXIMUM WORKING PRESSURE Model Curve Number Up to VM Up to VM Up to VM VM Up to VM VM Up to VM VM VM65 range 1 Up to VM9-4 1 The following figure shows the limitation of working pressure and temperature of VM pumps. Pumps should only be operated within the region shown by the curves below. P(bar) T( o C) 1 IDENTIFICATION OF THE PUMP SET SMAN 32-2A/3 WM Control Box Blank = Stand mount WM = Wall mount Motor fitted Blank = Single phase /3 = Three phase Impeller variation (A = manufacturer s turndown) Number of stages Nominal capacity of VM Pump at BEP in m 3 /hr Speedman Pump Set ALTITUDE & TEMPERATURE VS LOSS OF HEAD Guide only. Altitude and temperature losses are added. Altitude Loss of head m m 5m.6m 1m 1.15m 15m 1.7m m 2.m 25m 2.65m 3m 3.m Temperature Loss of head C.m 3 C.4m 4 C.7m 5 C 1.m 6 C 1.9m 7 C 3.1m 8 C 4.7m 9 C 7.1m 1 C 1.3m

3 HYDRAULIC PERFORMANCE VM3, 2 POLE 5Hz VM5, 2 POLE 5Hz VM3-23 VM3-19 VM3-15 VM3-12 VM3-8 VM3 5Hz Q(m 3 /hr) Q(m 3 /hr) VM5-16 VM5-14 VM5-12 VM5-1 VM5-8 VM5-5 VM5 5Hz Q(l/s) Q(l/s) VM1, 2 POLE 5Hz VM16, 2 POLE 5Hz Q(m 3 /hr) VM1-14 VM1-12 VM1-1 VM1-8 VM1-6 VM1-4 VM1 5Hz VM16-11 VM16-8 VM16-6 VM16-4 VM16-3 VM16-2 VM16 5Hz Q(m 3 /hr) Q(l/s) Q(l/s) NOTE: CURVE TOLERANCE IN CONFORMITY WITH ISO996 APPENDIX A.

4 HYDRAULIC PERFORMANCE VM32, 2 POLE 5Hz VM65, 2 POLE 5Hz VM32-8 VM32 5Hz VM65-5 VM65 5Hz 14 1 VM VM65-4A 1. 1 VM VM VM32-4 VM VM65-3A VM VM32-2A.4 4 VM65-2A.2. Q(m 3 /hr) Q(m 3 /hr) Q(l/s) Q(l/s) VM9, 2 POLE 5Hz PRESSURE BOOSTING VM9-4 VM9-4A VM9-3 VM9 5Hz The Speedman pumpset uses pressure boosting to determine when there is flow in the system. Periodically, it will momentarily boost the pressure and then watch for the pressure to decay back to the set point. If there is no decay within a set time period the system deems there is no-flow and shuts down. OPTIONS Boost frequency setting: 4, 8, 1 or 16 seconds Boost pressure setting: 3%, 6%, 12% and 18%.8 8 VM9-3A Boost decay test time: 2, 1, 3 and 6 seconds VM Q(m 3 /hr) Q(l/s) NOTE: CURVE TOLERANCE IN CONFORMITY WITH ISO996 APPENDIX A.

5 DIMENSIONS Pump Model Motor kw Height mm Length mm Width mm Pipe DN mm 3-8 SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN SMAN A SMAN32-2A SMAN SMAN SMAN SMAN SMAN A SMAN65-2A (Table E) 65-2 SMAN (Table E) 65-3A SMAN65-3A (Table E) 65-3 SMAN (Table E) 65-4A SMAN65-4A (Table E) 65-5 SMAN (Table E) 9-2 SMAN (Table E) 9-3A SMAN9-3A (Table E) 9-3 SMAN (Table E) 9-4A SMAN9-4A (Table E) 9-4 SMAN (Table E)

6 VM3, 5, 1, 16 and 32 VM3,5 = Ø32 VM1 = Ø4 VM16 = Ø5 VM32 = Ø65 VM3,5,1 = 1153 VM16,32 = 117 Ø VM3,5,1 = 46 VM16,32 = 43 VM3,5,1 = 51 VM16,32 = 48 VM3,5 = 675 VM1 = 74 VM16,32 = 775 VM3,5 = 128 VM1 = 133 VM16 = 16 VM32 = 175 VM65 and VM Specific dimensions for each model available on request

7 MOTOR TECHNICAL SPECIFICATIONS Motor 1 Phase Frame IP Rating FLC 24 V Start/LRC Ratio RPM Eff % Drive End Bearings Non-D/End.75 8 V18 IP ZZ 64-ZZ V18 IP ZZ 64-ZZ V18 IP ZZ 65-ZZ V18 IP ZZ 65-ZZ Motor 3 Phase Frame IP Rating FLC 415 V Start/LRC Ratio RPM Eff % Drive End Bearings Non-D/End.75 8 V18 IP ZZ 64-ZZ V18 IP ZZ 64-ZZ V18 IP ZZC3 65-ZZC V18 IP ZZC3 65-ZZC V18 IP ZZC3 65-ZZC V18* IP S 636-S V1* IP B 638ZZC V1* IP B 638ZZC V1* IP B 639ZZC V1* IP B 639ZZC V1* IP B 639ZZC V1* IP V1* IP *Special motor bearings fitted for thrust management.

8 Davey Water Products Pty Ltd Member of the GUD Group ABN AUSTRALIA Head Office and Manufacturing 6 Lakeview Drive, Scoresby, Australia 3179 Ph: Fax: Website: davey.com.au NEW ZEALAND 7 Rockridge Avenue, Penrose, Auckland 161 Ph: Fax: sales@daveynz.co.nz Website: daveynz.co.nz REST OF WORLD 6 Lakeview Drive, Scoresby, Australia 3179 Ph: Fax: export@davey.com.au Website: davey.com.au H/O & MFG SCORESBY Quality ISO 91 H/O & MFG SCORESBY Environment ISO 141 Customer Service Centre Ph: Fax: sales@davey.com.au Customer Service Centre Ph: This literature is not a complete guide to product usage. Further information is available from your Davey dealer, Davey Customer Service Centre and from the relevant product Installation and Operating Instructions. This data sheet must be read in conjunction with the relevant product Installation and Operating Instructions and all applicable statutory requirements. Product specifications may change without notice. Davey is a registered trademark of Davey Water Products Pty Ltd. Davey Water Products Pty Ltd 11. DPM251-1/5K/811/IPM supersedes DPM251a/311/WEB & DPM251/5K/18/IPM