Flow Characteristics NAR1 NAR 9 6 M5X.8 NAR2 NPT 3/ Flow (scfm) NAR5 NPT 3/ Flow (scfm) Flow (

Transcription

1 How To Order NAR 1, 2, 25,, 4, 5, 6 Regulator Body size 1 M5 2 1/8 25 1/4 3/8 4 1/2 5 3/4 6 1 NAR N 3 BG 1N Port Thread Nil Rc(PT) F G(PF) N NPT Accessories and Combinations Accessory Suffix 1 4 N R Port size M Nom.(M5) 1 1/8 2 1/4 3 3/8 4 1/2 6 3/4 1 1 Optional specifications Modular Air Components Nil None 1 3~ psig (.2~.2 MPa) setting* 4 3~6 psig (.2~.4 MPa)setting* N Non-relieving R IN-OUT reversal (Right Left) When specifying more than one option, please list numerically, then alphabetically. *Not a maximum setting. Option 1 is more precise in the range of 3~ psig. Option 4 is more precise in the range of 3~6 psig. Accessory Code B Description Bracket Applicable model NAR1~NAR6 Pressure G gauge NAR1~NAR6 Combination No Combination Part Number NAR1 NAR2 NAR25 NAR~NAR6 3~ psig (.2~.2 MPa) 1 3~6 psig (.2~.4 MPa) 4 Non-relieving N In-Out Reversal R 42

2 Flow Characteristics NAR1 NAR 9 6 M5X.8 NAR2 NPT 3/ Flow (scfm) NAR5 NPT 3/ Flow (scfm) Flow (scfm) 9 6 NPT 1/ Flow (scfm) NAR4 NAR Flow (scfm) NPT 1/ Flow (scfm) NPT 1 Flow Characteristics NAR 1, 2, 25,, 4, 5, 6 NAR Condition:Supply pressure 1 psig NPT 3/ Flow (scfm) NAR4-6 NPT 3/ Flow (scfm) 43

3 Pressure Characteristics NAR 1, 2, 25,, 4, 5, 6 Pressure Characteristics NAR1 Set Point Supply Pressure (psi) NAR2 NPT 1/ Supply Pressure (psi) NAR Supply Pressure (psi) NAR 33 Set Point Set Point Set Point Condition:Supply pressure 1 psig Secondary pressure psig, Flow rate.7 SCFM M5X.8 NAR4 NPT 1/2 NPT 3/8 NAR5 NPT 3/ Supply Pressure (psi) Supply Pressure (psi) NAR4-6 NAR6 Set Point Set Point Set Point NPT 3/ Supply Pressure (psi) NPT 3/ Supply Pressure (psi) Set Point NPT Supply Pressure (psi) Modular Air Components Precautions Read carefully before handling. Refer to the safety instructions and precautions section for the products mentioned in this catalog. Selection 1 For NAC, 4, NAC4, 44 with float type auto drain (N.O.), use 2.2kW {2 l/min (ANR)} or larger compressor. Because two auto drains are used and 2 l/min air is needed, it might cause a malfunction with a compressor weaker than the required ability. Installation 1 Flush piping before installation. 2 Use of piping adapters will ease installation. 3 The regulator may be installed with the adjustment knob up or down. If using the pressure switch (IS1M) and/or the T-type spacer, the regulator knob must face down. 4 The NAKM check valve is designed to be used between the regulator and the lubricator when it is necessary to prevent the possibility of lubricant flowing back into a non-lubricated secondary supply line. 5 When mounting residual pressure release 3- port valve upstream of a lubricator, use check valve (series NAKM) to prevent reverse flow of oil. 6 Pressure switch and T-type interface cannot be mounted to OUT side of residual pressure release 3-port valve. Piping Warning: When mounting check valve, make sure of the position of mark which indicates air flow direction. 44

4 ANSI Symbol Main Parts No. Name 1 Body 2 Bonnet No. NAR1 NAR Material NAR1 2 NAR25 NAR4~6 Zinc die casting Parts Name 3 Diaphragm ass' y 4 Valve ass' y 5 Valve spring 6 Valve O-ring 7 Piston mini Y packing 8 O-ring 9 O-ring Polyacetal Component Parts/Packing List Aluminum die casting Zinc die casting NAR2 NAR6 Note Platinum silver painting Black painting Construction/Parts List NAR 1, 2, 25,, 4, 5, 6 Material Part No. NAR1 NAR2 NAR25 NAR NAR4 NAR4-N6 NAR5 NAR6 N BR 1314A A 13A A A A 1318A Brass A 134A 13164A A 131A 13184A stainless steel N BR P11 P M YN-1A N BR P3 P P14 P G5 G55

5 46 Dimensions NAR 1, 2, 25,, 4, 5, 6 NAR1-4 NAR6 Model N AR Nom. (M5) NAR2 1/8 1/ 4 NAR25 1/4 3/ 8 NAR 1/4 3/ 8 NAR4 1/4 3/8 1/ 2 NAR4-N6 3/ 4 NAR5 3/4 1 NAR6 1 Port Size A B C D E 1.57 (4) (7) 2.95 () 3.54 (9) 3.74 (95) 2.42 (61.5).43 (11) (95) (17) 4.4 (12.5) (127.5) (35) (149.5) (37.5) (4.5) (4.5) (168) (48) (24.5) (48) NAR (4) 1.89 (48) 2.9 (7) (7) 3.54 (9) 3.74 (95) 1.2 (26) 2.28 (58) 2.44 (62) 2.44 (62) (7) 2.91 (74) 3. (8) 3.25 (82.5) Modular Air Components NAR1~: Max. Panel thickness: 9/64 (3.5mm) NAR4~5: Max. Panel thickness: 13/64: (5mm) With Bracket F G H J K L M N P (28) () (4.5) (6.5) (4) (2) (2.5) (19) () (34) (44) (5.4) (.4) (55) (2.3) (33.5) () (34) (44) (5.4) (.4) (55) (2.3) (33.5) (41) (4) (46) (6.5) (8) (2.3) (42.5) (32.5) (5) (54) (54) (8.5) (1.5) (7) (2.3) (52.5) () (5) (54) (56) (8.5) (1.5) (7) (2.3) (52.5) (38) (7) (66) (65.8) (11) (13) (9) (3.2) (52.5) (44) (7) (66.6) (65.8) (11) (13) (9) (3.2)

6 Tamper Proof Regulator AR 2 2BG R X33US. NAR Options NAR 1, 2, 25,, 4, 5, 6 Secondary pressure is preset and cannot be changed or secondary pressure can be set/adjusted in the field with a special tool. Regulator Family Set Pressure Supply Pressure Family Description Port Thread Tolerance Port Thread *RC(PT), G(PF) **NPT Applicable Model AC Air Combination +/- MPa (psi) *RC(PT), G(PF) **NPT AP Pressure Relief Valve ***NIL ***NIL All models listed below - ***NIL ***NIL AR Regulator.5 ~.7 7 ~ 1 AP.2 (3) see note 3 see note 3 see note 2 see note 2 ARB - see note 2 see note 2 ARB Interface Regulator see note 2 see note 2 ARBF - see note 2 see note 2 ARBF Interface Regulator.1 ~. 1 ~ 4 ARP.3 (.5).2 ~.8 2 ~ 1 ARP Precision Regulator.5 ~.7 7 ~ 1 AR111.7 (1).6 ~ 1. 8 ~ ARX 2 MPa Regulator.2 ~.85 3 ~ 12 AC2~55 AR2~5..1 (1.5).3 ~1. 4~ AW Filter Regulator AW/AWD/AWM2~4 AWD Micro Mist Separator Regulator.2 ~.7 3 ~ 1 AC/AR/AW1.3 (3.5).3 ~ 1. 4 ~ AWM Mist Separator Regulator.2 ~.7 3 ~ 1 SR.7 (1).3 ~ 1. 4 ~ SR Stainless Steel Regulator.5 ~.85 7 ~ 12 ARX.3 (4.5).6 ~ 2. 8 ~ 29 *Pressure Unit is MPa. ** Pressure Unit is psi. *** For regulator that includes tamper proof components but is not present, leave set & supply pressure blank. Same as Standard Note: Tamper Proof Regulator ø14 1. Dimensional changes from standard product are as shown. 2. Valve/subplate interface type regulators (ARB/ARBF) cannot be preset. 3. Since supply pressure equals set pressure for AP1, supply pressure indication is not required. Adjustment tools for X33US* tamper proof regulator Tool Description Bit, M5 spanner \with 1/4 hex shank Screwdriver, M5 spanner with nonremovable bit Restricted Regulator Regulator Family Family Description AC Air Combination AP Pressure Control Valve AR Regulator ARP Precision Regulator AW Filter Regulator AWD Micro Mist Separator Regulator AWM Mist Separator Regulator Part Number AR--X33US-1 AR--X33US-2 Retrofit kits for X33US* tamper proof regulator Restricted secondary pressure range (ex. 35psi maximum output regardless of input). AR 2 2BG R X34US. Same as Standard Note: No Dimensional changes from standard product. Bill of Materials Kit P/N Applicable Model P/N DESCRIPTION (QTY) KT-ARX2 KT-ARX21 ARX2 ARX21 ARX2--X33US-1 HANDLE (1) ARX2--X33US-2 ADJUST SCREW (1) - - AR1--X33US-3 TAMPER PROOF 8-1B SCREW KT-AR1-X33US AC/AR/AW/1 AR1--X33US-1 HANDLE (1) AR1--X33US-2 ADJUST SCREW (1) ADJUST NUT (1) SCREW (1) COVER (1) KT-AR2-X33US AC/AR/AW/AWD/A WM2~25 AR2--X33US-1 HANDLE (1) AR2--X33US-2 ADJUST SCREW (1) ADJUST NUT (1) M5X.8X12L TAMPER PROOF SCREW (1) KT-AR-X33US AC/AR/AW/AWD/A WM AR--X33US-1 HANDLE (1) AR--X33US-2 ADJUST SCREW (1) 1349 ADJUST NUT (1) KT-AR4-X33US AC4~55 AR4~5 AR4--X33US-1 HANDLE (1) AR4--X33US-2 ADJUST SCREW (1) ADJUST NUT (1) AW/AWD/AWM4 KT-ARP-X33US ARP ARP--X33US-1 HANDLE A (1) ARP--X33US-2 ADJUST SCREW (1) ARP--X33US-3 HANDLE B (1) KT-ARBF5-X33US ARBF5 ARBF5----X33US-1 ARBF5----X33US-2 - SCREW COVER SPACER (1) ADJUST SCREW (1) KT-ARB11-1-X33US ARB11-*-1 - KT-ARB11-2-X33US ARB11-*-2 ARBF5----X33US-1 SCREW COVER SPACER (2) ARBF5----X33US-2 ADJUST SCREW (2) - M5X.8X12L TAMPER PROOF SCREW (2) 8-1B SCREW COVER (2) KT-AP1-X33US AP1 AP1--X33US-1 SCREW COVER SPACER (1) AP1--X33US-2 HANDLE RETAINING WASHER (1) - M5X.8X12L TAMPER PROOF SCREW (1) 8-1B SCREW COVER (1) KT-AR111-X33US KT-SR-X33US AR111 SR Pressure Setting Port Thread RC(PT), G(PF) NPT Applicable Model.1 ~. 1 ~ 4 ARP.2 ~.7 3 ~ 1 AR111.2 ~.85 3 ~ 12 AC,AR,AW,AWD,AWM.5 ~.7 7 ~ 1 AP Tamper Proof Regulator 47

7 Quickly exhausts air pressure on secondary side Internal check valve allows for reverse flow for precise force control of extending and retracting cylinder applications Modular design connects with other P/A air preparation equipment Specifications Regulator NAR 6 N 3 BG Regulator with check valve NAR 1, 26, 256, 6, 46, 56, 66 Model NAR1 NAR26 NAR256 NAR6 NAR46 NAR46-N6 NAR56 NAR66 P ort size 1-32 Nom (M5) 1/8 1/ 4 1/4 3/ 8 1/4 3/ 8 1/4 3/8 1/ 2 3/ 4 3/4 1 1 P roof pressure psig (MPa) (1.5) Max oper. pressure psig (MPa) (1.) Regulating range pres. psig (MPa) 7~1 (.5~.7) ~12 (.1~.85) (OUT IN) Cv. 1/8:.33 1/4:. 1/4: 1. 3/8: /4: /8: /4: /8: /2: G auge port size 1/16 Rc(PT) 1/8 NPT 1/8 NPT 1/8 NPT 1/4 NPT 1/4 NPT 1/4 NPT 1/4 NPT A mbient and media temperature 23 ~ 14 F (-5 ~ 6 C) Construction Relieving style /4: 7.5 1: 7.28 Weight lbs. (Kgf).18 (.8).57 (.26).57 (.26).86 (.39) 1.85 (.84) 2.7 (.94) 2.62 (1.19) 3.42 (1.55) Accessories (Optional) Name Part No. NAR1 NAR26 NAR256 NAR6 NAR46 NAR46-N6 NAR56 NAR66 Bracket B12 B B B32 B42 B42 B64A Gauge G27-P1-R1 K4A-MP1.-N1M K5A-MP1.-N2M How To Order NAR46 NAR6 NAR256 Body size Nom. (M5) 2 1/8 25 1/4 3/8 4 1/2 5 3/4 6 1 Option Specification Nil None Check Valve R In-Out Reversal Left Right Port Thread Nil Rc(PT) Accessory N NPT Nil None F G(PF) B Bracket G Gauge Port size M Nom. (M5) 1 1/8 2 1/4 3 3/8 4 1/2 6 3/4 1 1 R B64A 49

8 Principal of Operation NAR 1, 26, 256, 6, 46, 56, 66 When primary pressure (P1) is higher than the secondary pressure (P2), the operation follows that of a standard regulator (see Figure 1 ). If P1 is exhausted by shifting a valve, P1 is reduced and the pressure under the regulator valve 4 will vent to P1. Therefore, the force pushing on the regulator valve 4 will be reduced to only the valve spring 5 which opens the passage from P2 to P1. This slowly decreases the pressure in the lower chamber of the diaphragm 1 and the force of the adjustment spring 3 exerts a force directly to the valve stem. This completely opens the flow path from P2 to P1 (see Figure 2 ) and quickly exhausts the pressure from P2 to P1. When primary pressure (P1) is higher than the secondary pressure (P2), the internal check valve 2 will seat, and the operation follows that of a standard regulator (see Figure 1 ). If P1 is exhausted by shifting a valve, the internal check valve 2 will crack open (P1 is less than the pressure in the lower diaphragm chamber 1). See Figure 2. The force of the adjustment spring 3 pushes directly on the valve stem and opens the Flow path from P2 to P1 completely (see Figure 3 ) and quickly exhausts the pressure from P2 to P1. ❶ Modular Air Components Setting The adjustment knob is the locking type. Pull the knob away from the body until the orange band is visible. Adjust as necessary and push the knob back into its locked position to prevent accidental setting change. ❷ Turning the adjustment knob clockwise increases the pressure and turning the knob counter clockwise will reduce the pressure. Check supply pressure before adjusting pressure. Precautions <Installation> ❶ Air flush piping before installation. ❷ Install with at least 2.5 in. of free space below the unit to allow easy access. 5

9 Flow Characteristics NAR1 9 6 NAR26 M5 NAR46 NPT 1/ NPT 1/4 NAR46-6 NPT 3/ NAR256 NPT 3/8 NAR56 NPT 3/ NAR26 NPT 3/8 NAR46-6 NPT Conditions: Supply pressure 1 psi Flow Characteristics NAR 1, 26, 256, 6, 46, 56, 66 51

10 Pressure Characteristics NAR 1, 26, 256, 6, 46, 56, 66 Pressure Characteristics NAR1 Secondary pressure (PSI) Supply pressure (PSI) NAR26 Secondary pressure (PSI) Supply pressure (PSI) NAR26 Secondary pressure (PSI) Supply pressure (PSI) NAR26 Secondary pressure (PSI) Supply pressure (PSI) NAR46 Secondary pressure (PSI) Supply pressure (PSI) NAR46-6 Secondary pressure (PSI) Supply pressure (PSI) NAR46-6 Secondary pressure (PSI) Supply pressure (PSI) NAR46-6 Secondary pressure (PSI) Supply pressure (PSI) Modular Air Components Conditions: Supply pressure 1 psi Secondary pressure psi Flow rate.7 SCFM 52

11 NAR1 NAR46 56 Main Parts No. No. Name 1 Body 2 Bonnet Parts Name 3 Diaphragm ass' y 4 Valve ass' y 5 Valve spring 6 Valve O-ring 7 Piston mini Y packing 8 O-ring 9 O-ring Material NAR1 26 NAR256 6 NAR46~66 Zinc die casting Polyacetal Component Parts List/Packing List Aluminum die casting Zinc die casting NAR NAR66 Note Platinum silver painting Black painting (NAR46~NAR66) Construction/Parts List NAR 1, 26, 256, 6, 46, 56, 66 Material Part No. NAR1 NAR26 NAR256 NAR6 NAR46 NAR46-N6 NAR56 NAR66 N BR A 131A 13528A A A A 1318A Brass A 13529A 13165A A 131A 13184A Stainless steel XTO N BR ø.53 X ø.47 X ø N YN-1A N BR P3 P P14 P G5 G55 53

12 Dimensions NAR 1, 26, 256, 6, 46, 56, 66 NAR1~56 NAR66 Model N AR Nom. (M5) NAR26 1/8 1/ 4 NAR256 1/4 1/ 8 NAR6 1/4 3/ 8 NAR46 1/4 3/8 1/ 2 NAR46-6 3/ 4 NAR56 3/4 1 NAR66 1 Port size A B C D E 1.57 (4) (7) 2.95 () 3.54 (9) 3.74 (95) 2.42 (61.5) 3.66 (93) 4.4 (12.5) 5.2 (127.5) 5.89 (149.5) 6.8 (4.5) 6.61 (168) 8.5 (24.5).43 (11).59 () 1.38 (35) 1.48 (37.5) 1.59 (4.5) 1.89 (48) 1.89 (48) 1.57 (4) 1.89 (48) 2.9 (7) (7) 3.54 (9) 3.74 (95) 1.2 (26) 2.28 (58) 2.44 (62) 2.44 (62) (7) 2.91 (74) 3. (8) 3.25 (82.5) Modular Air Components With Bracket F G H J K L M (28) () (4.5) (6.5) (4) (2) () (34) (44) (5.4) (.4) (55) (2.3) () (34) (44) (5.4) (.4) (55) (2.3) (41) (4) (46) (6.5) (8) (2.3) (5) (54) (54) (8.5) (1.5) (7) (2.3) (5) (54) (56) (8.5) (1.5) (7) (2.3) (7) (66) (65.8) (11) (13) (9) (3.2) (7) (66) (65.8) (11) (13) (9) (3.2) N.81 (2.5) 1.32 (33.5) 1.32 (33.5) 1.67 (42.5) 2.7 (52.5) 2.7 (52.5) 2.7 (52.5) øn inch (mm) P. (19) 1.28 (32.5) 1.42 () 1.5 (38) 1.73 (44) 54

13 Allows quick relief of air when the supply air is less than set pressure Modular design connects with other P/A air preparation equipment NAR- BG NAR5- BG NAR255 Specifications Regulator with Quick Relief NAR 255, 5, Model NAR255 NAR5 NAR NAR-N6 Port size NPT 1/4 3/ 8 1/4 3/ 8 1/4 3/8 1/ 2 3/ 4 P roof pressure psig (MPa) (1.5) M ax. oper. press. psig (MPa) (1.) R egulating range psig (MPa) 7 ~ 12 (.5 ~.85) Port size for pressure gauge 1/ 8 1/ 8 1/ 4 1/ 4 A mbient and media temp. 23 ~ 14 F (-5 ~ 6 C) Construction Relieving style W eight lbs. (Kgf).6 (.27).9 (.41) 1.85 (.84) 2.7 (.94) Attachments/Accessories (Optional) Type Part No. NAR255 NAR5 NAR NAR-N6 Bracket B B32 B42 B42 Pressure gauge K4A-MP1.-N1M K4A-MP1.-N1M K5A-MP1.-N2M K5A-MP1.-N2M How To Order Regulator NAR 5 N 3 Body size 25 1/4 3/8 4 1/2 Quick Relief Port Thread Nil Rc(PT) N NPT F G(PF) Port size 2 1/4 3 3/8 4 1/2 6 3/4 BG Nil B G 1N Optional Specifications Nil None 1* 3~psig (.2~.2MPa)setting 4* 3~6psig (.2~.4MPa)setting N Non-relieving R In-Out Reversal Right Left *Not a maximum setting. Option 1 is more precise in the range of 3~ psig. Option 4 is more precise in the range of 3~6 psig. Accessory None Bracket Gauge 55

14 Modular Air Components Regulator with Quick Relief NAR 255, 5, NAR NAR5 6 Selection Warning NPT 3/4 NAR-N Mounting/Adjustment NAR255 The adjustment handle must be operated manually. Using a tool to turn the handle could lead to damage. Set up the regulator while verifying the pressure that is indicated on the primary and the secondary pressure gauges. Turning the handle excessively could damage the internal parts. 6 Caution Conditions: Supply pressure 1 psi Secondary pressure psi Flow rate.7 SCFM NPT 1/2 NAR pn e NAR5 NPT 3/ Orange mark NPT 3/4 87 NAR-N Supply Pressure (PSI) 56 6 Release the lock to adjust the pressure. After the adjustment, engage the lock. Failure to observe this procedure could damage the handle or cause the secondary pressure to fluctuate. 1)On the AR255, pull the adjustment handle to release the lock and push the adjustment handle to engage the lock. If it does not lock easily, turn the handle slightly clockwise or counterclockwise before pushing it. 2)On the AR5 and AR, pull the adjustment handle to release the lock. (An orange colored line is provided at the bottom of the adjustment handle for visual checking.) Push the adjustment handle to engage the lock. If it does not lock easily, turn the handle slightly clockwise or counterclockwise; then, push it until the orange colored line is no longer visible. Valve guide Supply Pressure (PSI) Supply Pressure (PSI) 212 NPT 3/8 Warning 1 Pressure Characteristics Do not use between the cylinder and the switching valve. To prevent a lag in the discharge time, use a regulator with a check valve. 9 Be sure to read before handling. Refer to page 6 for Safety Instructions and precautions common to products mentioned in this volume and refer to pages 7 and 8 for more detailed precautions of every series. 7 NPT 3/8 9 6 NPT 1/2 NAR 9 Conditions: Supply pressure 1 psi NPT 3/8 9 Precautions ua ir e Flow Characteristics 1 Install the valve guide (on the opposite side of the handle) 6mm away from the ground surface to facilitate maintenance inspection. To use this product between the solenoid valve and the actuator, contact P/A Supply Pressure (PSI) 1

15 Construction/Parts List NAR255 5 Component Parts No. Description Body Bonnet Replacement Parts Material NAR255 NAR5 NAR NAR-6 Aluminum die casting Polyacetal Aluminum die casting No. Description Material Diaphragm ass'y Valve ass'y Valve spring Check packing O ring O ring Dimensions NAR255 5 Model NAR255 1/4 1/ 8 NAR5 1/4 3/ 8 Brass/ Stainless steel NAR 1/4 3/8 1/ 2 NAR-6 3/ 4 NAR255 NAR5 NAR NAR-6 NAR A 13144A P3 P Port size A B C D E (7) 2.95 () 4.4 (12.5) 5.2 (127.5) 5.89 (149.5) 6.8 (4.5) Note Platinum silver paint Black paint (NAR) Part no. NAR5 NAR NAR-6 13A A A 134A A A (35) 1.48 (37.5) 1.59 (4.5) 1.89 (48) 2.9 (7) (7) 2.44 (62) 2.44 (62) (7) 2.91 (74) When the primary pressure is higher than the set pressure, the check seal opens and the regulator works as a normal pressure relief valve. (See fig. 2). In the bottom valve chamber, the secondary pressure flows through the clearance between the valve and valve stem. When the primary pressure is blocked, the check seal folds and the pressure in the bottom valve chamber passes to the primary pressure side (see fig. 3). Because the flow area of the check seal is larger than that of the clearance between the valve and valve stem, differential pressure is created between the top and bottom chambers of the valve and the valve opens. The diaphragm is then pushed up by the pressure adjustment spring to let the valve fully open. The secondary pressure then rapidly discharges to the primary pressure side. With Bracket F G H J K L M () (34) (44) (5.4) (.4) (55) (2.3) (41) (4) (46) (6.5) (8) (2.3) (5) (54) (54) (8.5) (1.5) (7) (2.3) (5) (54) (56) (8.5) (1.5) (7) (2.3) Regulator with Quick Relief NAR 255, 5, When the primary pressure is applied When the primary pressure is exhausted øn NAR255~5: Max. Panel thickness: 9/64 (3.5)mm NAR: Max. Panel thickness: 13/64 (5mm) SAC2, #2 SAC253, #2 SAC4, #2 SAC46, #2 N 1.32 (33.5) 1.67 (42.5) 2.7 (52.5) 2.7 (52.5) inch (mm) P 1.28 (32.5) 1.42 () 1.5 (38) 57

16 NARP Series Precision Regulator NARP NARP-2 NARP-2BG Specifications How To Order Precision Regulator Model NARP Port size 1/ 4 P roof pressure psig (MPa) 174 (1.2) M ax. working pressure psig (MPa) 1 (.8) N ARP N 2 BG R Port Thread Nil Rc(PT) N NPT F PF Port size 2 1/4 Modular Air Components S et pressure psig (MPa).7 ~ (.5 ~.3) S ensitivity psig (MPa). (.1) R epeatability psig (MPa) ±. (±.3) Air consumption psig A mbient and fluid temperature 4 ~ 14 F (-5 ~ 6 C) Construction Relieving style W eight lbs (Kgf).93 (.42) Accessories (Optional) Option Part Number Bracket B32 Gauge ~ 6 psig ( ~.4 MPa) K4-MP.4-N1S Accessory Nil None B Bracket G Gauge ANSI Symbol Optional specifications Nil None R IN-OUT reversal 58

17 Construction/Parts List Dimensions Setting ❶ The adjustment knob is the locking type. Pull the knob away from the body until the orange band is visible. Adjust as necessary and push the knob back into its locked position to prevent accidental setting change. Component Parts No. Name ❶ Body ❷ Bonnet ❷ Turning the adjustment knob clockwise increases the pressure and turning the knob counter clockwise will reduce the pressure. ❸ Check supply pressure before adjusting pressure. Replacement Parts No. ❸ ❹ ❺ ❻ ❼ ❽ Name Diaphragm Ass y Valve Ass y Valve Spring Packing O-ring O-ring Material Brass+ SUS Material Note ADC Platinum silver painting ADC Black painting Part number 1351A 1356A MYN-5 P6 13 Precautions <Installation> ❶ Air flush piping before installation. ❷ Install with at least 2.5 in. of free space below the unit to allow easy access. NARP Series Precision Regulator NARP Pressure/Flow Characteristics Supply Pressure (PSI) 7 Supply pressure 72 psig Secondary pressure psig Flow Rate Set point Supply pressure 1 psig Flow Rate (SCFM) 59