Risk Guide: Manual Handling

Size: px
Start display at page:

Download "Risk Guide: Manual Handling"

Transcription

1 Risk Guide: Manual Handling Date Description of Original Document/Amendments Prepared/Edited By 11/06/14 Initial Draft Jasmina Lozanovska 17/06/14 Released Version Jasmina Lozanovska 30/09/14 Released Version Nil Jasmina amendment Lozanovska 27/08/15 Released Version Nil Jasmina amendment Lozanovska Approved By Michelle Gagovski Michelle Gagovski Michelle Gagovski Michelle Gagovski Page 1 of 21

2 Risk Guide: Manual Handling Introduction: Manual handling is any activity that involves lifting, pushing, pulling, carrying, moving, holding or restraining. It also includes sustained and awkward postures or repetitive movements. Hazardous manual handling can lead to injuries or disorders of the muscles, nerves, tendons, joints, cartilage and spinal discs. Some of these injuries are referred to as sprains and strains, back injuries, lower back pain, soft-tissue injuries to the wrists, arms, shoulders, neck or legs or abdominal hernias. Collectively, these conditions are known as musculoskeletal disorders (MSDs). Good manual handling techniques can help to prevent such injuries. Cleaning Melbourne s Risk Guide: Manual Handling is a Guide for employees in safe manual handling practices. All employees are responsible for following the steps detailed in this Guide for any manual handling activity as defined above. Manual Handling: Manual handling tasks are part of the job for cleaners, but in certain circumstances they can be hazardous and cause injuries. Cleaning Melbourne has a moral and legal responsibility to protect its employees from manual handling injuries. At the same time, employees have a general duty to take reasonable care for their own health and safety and that of others who may be affected by their work. Employees are also obligated to cooperate with Cleaning Melbourne s efforts to make the workplace safe. To achieve these responsibilities employees must: Use manual handling equipment properly Follow Cleaning Melbourne s policies and procedures (EG: No Lift Policy) Attend health and safety training Undertake any further training required Not take any shortcuts that could increase the risks associated with manual handling Notify Cleaning Melbourne of any hazardous manual handling tasks that they become aware of. How to Recognise Hazardous Manual Handling Tasks: Identifying hazardous manual handling tasks can help Cleaning Melbourne take action to eliminate or reduce the risk of manual handling activities being hazardous to employees. Suggesting modifications to the way a task is performed or suggesting aids and equipment that may make tasks safer can be ways employees can help to reduce the occurrence of hazardous manual handling tasks in the workplace and thus musculoskeletal injuries. Employees, as well as Cleaning Melbourne, can take the following steps to further ensure hazardous manual handling tasks are recognised and managed. Step 1: Identify which tasks involve Hazardous Manual Handling Evaluate all work tasks which involve manual handling to determine which pose a risk of MSDs in the workplace. Use the attached Manual Handling Risk Factor Table, Manual Handling Hazard Identification Worksheet, Manual Handling Risk Assessment Worksheet, Manual Page 2 of 21

3 Handling Risk Control Worksheet, Manual Handling Action Plan and Manual Handling Safe Work Procedure Worksheet to: List all the tasks that involve manual handling Identify the tasks that involve hazardous manual handling Prioritise the tasks to be assessed. Step 2: Carry Out Risk Assessments of Hazardous Manual Handling Tasks Do an assessment of all hazardous manual handling tasks. Ensure your assessments is as detailed as possible. Remember to take into account factors including postures, movements, forces, duration, frequency of task and environmental factors (such as heat, cold and lighting levels). A risk assessment record helps you to: Select and maintain appropriate risk controls Evaluate the effectiveness of these risk controls in subsequent risk assessments Avoid introducing tasks that may result in MSDs Avoid unnecessarily assessing a task more than once. Step 3: Develop and Implement Solutions Once you have carried out a risk assessment, you will need to develop and implement solutions. To eliminate or reduce the risk of a MSD associated with a hazardous manual handling task, one or more of the following risk controls must be used: Alter your workplace layout, workstation design, the working position of employees or the environment conditions where the task involving manual handling is taking place by changing the height, placement and design of equipment, furniture and objects used (EG: provide equipment with adjustable height, provide workers with adequate work space) Alter the systems of work used to carry out the manual handling task Change the objects used in the manual handling task (EG: provide adjustable platforms, scissor lifts, suspended hand tools, tools with anti-vibration or anti-kickstart features) Use mechanical aids (EG: trolleys, conveyors, hoists or forklifts) to move objects; or A combination of the above methods. * For some tasks, you may need to use several risk controls to eliminate or reduce the risk of MSDs associated with a hazardous manual handling task. If none of these controls are practicable, you may use information, training or instruction in manual handling techniques to reduce the risk. However, such methods may not be solely or primarily implemented unless other risk controls are demonstrated as being impracticable. Page 3 of 21

4 Key Contacts: David Gagovski Managing Director Cleaning Melbourne Pty Ltd Ph: 1300 BE CLEAN ( ) Michelle Gagovski Business Manager Cleaning Melbourne Pty Ltd Ph: 1300 BE CLEAN ( ) Jasmina Lozanovska Office Administration Assistant Cleaning Melbourne Pty Ltd Ph: 1300 BE CLEAN ( ) Page 4 of 21

5 Manual Handling Tips: Lifting Objects Cleaning Inside Bathtubs/ Spa Baths Cleaning Mirrors, Tiles and Glass Walls TIPS FOR CORRECTLY: Test the weight of the object Plan route Wide stance Bend knees Get close to the object Obtain a firm grip Maintain a stable position Tighten stomach Use your legs Keep your back straight Lift smoothly Avoid or minimise bending, twisting and reaching out with weight Avoid repetitive or awkward postures (EG: bending and kneeling) Improve posture by using tools with long handles or extended poles Use tools with flexible cleaning head frame that can clean both contoured and flat surfaces Avoid repetitive or awkward postures (EG: cleaning above shoulder height by reaching upwards) Avoid reaching by use equipment with a long handle or extendable pole Reduce force and repetitive gripping Use chemicals that are safe and require less effort to use Use materials that require less effort to use (EG: specially treated cotton cloths or microfibre sponges and cloths) Use equipment suited to the size of the surface areas being cleaned (EG: handled sponges with larger heads for cleaning large areas) EXAMPLES: Page 5 of 21

6 Manual Handling Tips (continue) Cleaning Showers TIPS FOR CORRECTLY: Avoid repetitive or awkward postures and sustained force (EG: bending, reaching above shoulder height, twisting the back, squatting, kneeling, wiping and scrubbing) Improve posture by using tools with long handles or extended poles Use tools with flexible cleaning head frame that can clean both contoured and flat surfaces Use heads or brushes specifically designed to fit easily into crevices and grooves Use chemicals that are safe and require less effort to use Use materials that require less effort to use (EG: specially treated cotton cloths or microfibre sponges and cloths) Use equipment suited to the size of the surface areas being cleaned (EG: handled sponges with larger heads for cleaning large areas) EXAMPLES: Cleaning Tables and Desks Avoid repetitive or awkward postures (EG: cleaning large tables, cleaning low tables and cleaning desks by reaching, bending or twisting) Improve posture by using tools with long handles or extended poles (EG: use a long handled duster or washcloth) sff Page 6 of 21

7 Manual Handling Tips (continue): Cleaning Toilets and Urinals TIPS FOR CORRECTLY: Avoid repetitive or awkward postures (EG: cleaning large toilets or urinals by bending the back) Improve posture by using tools with long handles or extended poles (EG: longhandled brushes/sponges) Use tools with flexible cleaning head frames that can clean both contoured and flat surfaces Use a steam-cleaning machine with a variety of tools or necessary accessories to clean urinals and inside, outside and behind toilets Avoid repetitive or awkward postures and sustained force (EG: cleaning the surface of toilets or urinals by using force with one hand while in an awkward posture) Eliminate or reduce repetitive and sustained force by using cleaning chemicals that are safe and require less effort to use and long handled tools with suitable brushes that require less effort to use (EG: bristle brush) EXAMPLES: Emptying Rubbish Bins Avoid repetitive, sustained or awkward postures (EG: collecting waste by bending and reaching arms away from the body or inserting new bin liners by bending) Reducing bending by positioning the bin on an elevated surface before emptying contents, use slimmer/taller bins, and regularly empty bins so they do not become too heavy Page 7 of 21

8 Manual Handling Tips (continue): TIPS FOR CORRECTLY: Mopping Avoid repetitive or sustained postures (EG: mopping surfaces by bending, positioning the elbow away from the body, overextending during push and pull movements and the figure-eight method and excessive wrist bending and twisting) Improve posture and reduce the risk of injury by using mops with extendable handles, mop small sections at a time to avoid extended reaching, step or shift legs to avoid twisting the upper body, use mechanised floor cleaning machines for medium to large areas, use bucket-less mops (EG: spray mops for small areas) Avoid repetitive or sustained movements (EG: wringing mops using hand squeeze mop buckets by bending and positioning the elbow away from the body) Use mechanised floor cleaning machines Use tall mop buckets or raise the mop bucket off the floor to reduce the bending force required to wring the water Moving Furniture, Rugs and Mats Keep elbows close to the body Avoid repetitive or sustained awkward postures (EG: moving furniture, rugs or mats below knee-height by bending and twisting) Reduce bending, twisting and high force by following Cleaning Melbourne s No Lift Policy, use cleaning equipment with handles with sufficient length so the cleaning head can be pushed under furniture, roll rugs and mats to expose the surface requiring cleaning EXAMPLES: Page 8 of 21

9 Manual Handling Tips (continue): TIPS FOR CORRECTLY: Vacuuming Avoid repetitive or sustained awkward postures (EG: vacuuming by bending and twisting the back and reaching forwards and sideways) To reduce bending, twisting and reaching by using mechanised cleaning machines for large floor areas, use extendable wand lengths or extra rods/tubes for lengthening wands, keep shoulder and elbow in a natural position close to the body, minimise body movements while vacuuming EXAMPLES: Page 9 of 21

10 Manual Handling Risk Factor Table LOOK AT LOOK FOR THE PROBLEM THE SOLUTION Actions and movements Bending forward/sideways Increased stress and strain to spine, Perform all movements (including Twisting back muscles and smoothly, in a repetitive Discomfort or pain limbs controlled, balanced, actions and Sudden jerky movements comfortable position movements) Repetitive bending, Minimise repetitive twisting or overreaching bending, twisting and overreaching Workplace /work station layout Working posture and position Load location and distances moved Duration and frequency Weights and forces Reaching above shoulder height or below mid-thigh Poor positioning of tools, controls, equipment or other materials Confined working positions or cramped workspace Objects that limit feet and leg movement and are held away from the body Tasks performed in one position for a long time Repetitive or frequent tasks performed in an uncomfortable position Loads moved a long distance or putting loads in specified or difficult locations Repetitive tasks performed for long periods, or at high speed, without a break Consider the weight of the load in relation to: Actions and movements Affects the posture and technique, restricts movement and causes muscles to tire Increases stress on the muscles and the spine Unbalanced load to the body Tires the muscles even if no load is involved Repetitive or frequent bent or twisted posture increases load on the back Stress on muscles increases risk of injury Muscle fatigue increases risk of injury Psychological impact The heavier the load, the greater the stress on the spine and muscle movements Carry out most work at waist level, within easy reach Position tools, controls, equipment and furniture to allow work to be done in a comfortable, upright position Hold loads close to body Perform variety of work tasks during the day or take regular breaks Carry out work in a comfortable position with regular changes in position and posture Store loads at an approximate height in close proximity to where they will be used Provide adequate space to facilitate ease of loading Perform a variety of work tasks during the day or take regular breaks Provide loads that are light and easy to handle Page 10 of 21

11 Manual Handling Risk Factor Table (continue) LOOK AT LOOK FOR THE PROBLEM THE SOLUTION Weights and forces Working posture and position when lifting When a person is seated there is extra Use mechanical aids or team lifting for (continue) Duration and frequency stress when they heavy loads of manual handling apply force or lift loads Change posture and Location of loads and distances moved Posture and working conditions affect the working conditions as necessary Characteristics of load risk associated with The risk of injury may Situations when: applying a force to increase when: Holding or restraining push, pull or restrain Lifting weights of does not result in an object more than 4.5kg movement Even light loads while seated Pushing levers or present a problem if Lifting weights more pulling objects, where they are lifted than 16-20kg the force may not relate incorrectly, Pushing, pulling and to the movement (EG: a repetitively, at speed, sliding objects that large force required to or in an unsafe are difficult to move move a lever a short environment Generally weights distance) over 55kg should not be lifted although any weight can be hazardous in certain Characteristics of loads Loads that are difficult to hold EG: awkward shapes, slippery surface or obscure vision Unpredictable or animate objects EG: people, animals or unstable loads Hot or cold loads that can t be held close to the body Stumbling with a load can strain the spine and back muscles Holding a load away from the body increases stress on the back and limbs circumstances Hold loads close to the body Provide loads that are compact, rigid and predictable, preferably with handles Use mechanical aids, straps or trolleys or team lifting Use PPE EG: gloves for hot, cold or slippery loads (while gloves may protect against burns/abrasions they adversely affect grip, strength and dexterity) Aprons may allow a load to be held close to the body but may affect mobility and comfort Page 11 of 21

12 Manual Handling Risk Factor Table (continue) LOOK AT LOOK FOR THE PROBLEM THE SOLUTION Work Poor work schedule and Fatigue and stress Eliminate organisation work procedures Pressure to lift by unnecessary manual Busy periods without themselves handling breaks Psychological impact Provide work Inadequate staff numbers schedules and work procedures that Unsuitable or insufficient mechanical aids allow for frequent rest periods and job rotation Unnecessary handling Organise work so it flows smoothly Ensure mechanical aids are available as required Train in safe team lifting procedures and use only where other means are not Work environment Skills and experience Slippery or uneven floors and rough ground Cluttered, confined workspaces Vibrating machinery Inadequate lighting Hot and cold environments Inadequate training or inexperienced staff Age Workers under 18 years of age, or older workers, performing manual handling tasks Consider the individual s fitness and physical suitability for the task not only their age Slips and falls Damage to spine and limbs Back and limb pain Risk of injury is increased if safe work procedures are unknown Older workers may be less able to cope with certain physical work Young developing bodies are more easily injured available Provide even, slipresistant floors Provide an uncluttered, well lit workplace Provide vibration free machinery or limit exposure to vibration Train all workers in the safest way to perform each task Ensure workers understand how to care for their bodies Don t assess risk on age alone older workers may compensate for physical loss with experience and skill Generally, workers under 18 years should not be required to lift, lower or carry objects weighing more than 16kg without Page 12 of 21

13 Manual Handling Risk Factor Table (continue) LOOK AT LOOK FOR THE PROBLEM THE SOLUTION Age (continue) mechanical or other assistance, or without specific training for the task Consider all relevant Clothing Inappropriate clothing may restrict movement EG: tight uniform, slippery shoes, loose gloves Special needs (permanent or temporary) Any other factors Workers returning from injury or illness, leave or with special needs EG: pregnancy, person with a disability, new to the job Any other considerations unique to the workplace, task or worker May affect posture and cause slips, trips and falls May affect grip resulting in unplanned or sudden movements People with permanent or temporary physical limitations may require: Time to build their physical capabilities sufficiently to perform the job Changes to the job Changes to the workplace May be difficult to address unique or unusual situational factors risk factors Provide proper clothing, footwear and PPE that allows workers to perform tasks with confidence and without restriction Take into account permanent or temporary special needs when: Designing the workplace Allocating work Developing procedures Developing suitable duties and the return to work plan Include in risk assessment even if not always applicable Page 13 of 21

14 Manual Handling Hazard Identification Worksheet Task description and location: Task on this sheet identified from (tick one only): Incident records Direct observation of work Consultation Other, please describe Information: 1. How many workers do this task? 2. How long do they do it? (duration) 3. How often do they do it? (frequency) 4. How many workers have reported pain from this task? 5. How many injuries have been attributed to this task? 6. What risk factors appear to be the main problem(s) with this task? Actions and movements Workplace and workstation layout Working postures/positions Load location and distances moved Duration and frequency Weights and forces Characteristics of loads and equipment Work organisation Work environment Skills and experience of worker Age of worker Clothing Special needs of worker Other factors (please describe) Page 14 of 21

15 Manual Handling Hazard Identification Worksheet (continue) 7. Are there other similar tasks? Yes No 8. If so, how do we manage them currently? 9. Does this task require a more detailed risk assessment? Yes, complete the Manual Handling Risk Assessment Worksheet and Manual Handling Risk Control Worksheet. No, copy this for filing and make available for consultation. Developed by: Date: Page 15 of 21

16 Manual Handling Risk Assessment Worksheet Task description and location: POSTURES/ACTIONS Actions and movements Bending or twisting the back Reaching/working above the shoulder Reaching/working below mid - thigh height Sudden or jerky movements Repetitive bending, twisting or overreaching Workplace and workstation layout DURATION/FREQUENCY Task is done for a long time by one worker A repetitive action is done at speed LOAD/FORCE Load location and distances moved The object is carried, pushed or pulled over a long distance or unnecessarily handled Weight and forces Workplace layout makes it hard to reach things involved in the task Work heights and/or seat heights unsuitable Insufficient space for all necessary movements Mechanical aids are not available or easily accessible Working postures and positions There is frequent or prolonged forward bending or stretching of the back There is frequent or prolonged twisting or sideways bending or stretching More than 4.5kg lifted while sitting More than 16kg is lifted while standing Combined with other risk categories: It is necessary to pull, push or side objects that are difficult to move A large force is applied white seated Characteristics of loads and equipment Live loads are manually lifted or moved Objects handled are large or have awkward shapes Objects are hard to grasp and hold Objects are wet, greasy and dirty and cannot be held close to the body (EG: very hot or cold) The object blocks the view when handled The load is unstable or may move suddenly Page 16 of 21

17 Manual Handling Risk Assessment Worksheet (continue) MANAGEMENT/ENVIRONMENT Work organisation There are busy periods when workers have difficulty keeping up with demands and no rest/recovery breaks Workers are not available for team lifting when required Manual handling equipment is not regularly maintained or is unsuitable or unavailable Work environment Floor are slippery or uneven There are different floor levels in the work area The work area is cluttered or untidy or confined Lighting is inadequate for the task Work is done in very hot, cold or windy conditions There is vibrating machinery Clothing Protective clothing or equipment is unsuitable or unavailable (EG: slippery shoes, loose gloves and clothing that restricts movement) Skills and experience Age Workers have not received appropriate training in manual handling Workers have not been properly instructed in safe work procedures Demands of the task exceed the physical capacity or experience of the workers Workers under 18 performing strenuous repetitive tasks, or lifting objects weighing more than 16 kgs Older workers performing tasks unsuitable for their physical capabilities Special needs There are workers at higher risk (EG: due to injury, pregnancy, recent illness, new employees or persons with a disability) OTHER Are there other risk factors not covered by the checklist? Provide details: Page 17 of 21

18 Manual Handling Risk Control Worksheet Elimination Can the manual handling task be eliminated? For example, redesign work activity, object or working environment. Yes, how can this be done? No Substitution Can the hazard be substituted with one that gives rise to a lesser risk? For example, reduce load size and shape. Yes, how can this be done? No Isolation Can the hazard be isolated from the worker at risk? For example, remote manual handling techniques. Yes, how can this be done? No Engineering Can engineering controls be used? For example, modify equipment or provide mechanical aids. Page 18 of 21

19 Manual Handling Risk Control Worksheet (continue) Yes, how can this be done? No Administration Can administrative controls be used? For example, change work practice, implement job rotation, training, develop/implement safe work procedure. Yes, how can this be done? No What training or instruction may be required? Personal protective equipment What PPE could be used to reduce the risks? For example, use gloves to improve handling or load. Yes, how can this be done? No Page 19 of 21

20 Manual Handling Action Plan Complete the action plan for all tasks that have completed risk assessment and control worksheets. Attach references to other documents such as drawings, detailed plans and work procedures. Outline how you will involve workers and what actions will be taken to improve the management of this risk. Work location/department Task Description Control Measures Approved By Implementation Date Person Responsible Evaluation Date Progress Page 20 of 21

21 Manual Handling Safe Work Procedure Worksheet Task description and location: Steps Risks Controls Developed by: Manager s name Worker s name Manager s signature Worker s signature Date created Review date Page 21 of 21

Manual Handling Procedure

Manual Handling Procedure Manual Handling Procedure Table of Contents 1 Purpose... 3 2 Scope... 3 3 Definitions... 3 4 Responsibilities... 3 4.1 Managers And Supervisors... 3 4.2 Workers (Employees, Contractors And Visitors)...

More information

Manual Tasks Minimum Standard. October, 2014

Manual Tasks Minimum Standard. October, 2014 Manual Tasks Minimum Standard Manual Tasks Minimum Standard October, 2014 Contents 1 Executive Summary... 2 2 More Information... 2 3 Using this Standard... 2 4 Managing Risk... 2 4.1 Consultation... 2

More information

Corporate Standard Manual Handling HB#

Corporate Standard Manual Handling HB# Contents Contents... 1 Functional Flowchart... 1 Objective... 1 Scope... 1 Definitions... 1 Responsibilities... 2 OH&S Systems Manager... 2 Station / Site Manager... 2 Workers... 2 Hazards... 2 Inspections

More information

ASSESSING AND CONTROLLING MANUAL HANDLING RISK

ASSESSING AND CONTROLLING MANUAL HANDLING RISK ASSESSING AND CONTROLLING MANUAL HANDLING RISK Location of task: Description of manual handling task: Date of assessment: Persons doing assessment: Work area management rep: Work area H&S rep (or deputy):

More information

2.18 Manual Handling Policy and Procedure Table of Contents

2.18 Manual Handling Policy and Procedure Table of Contents Table of Contents Section 1 - Policy... 3 1.1 Purpose... 3 1.2 Scope... 3 1.3 Requirements... 3 1.4 Responsibilities... 3 Section 2 - Procedure... 4 Section 3 - References... 9 3.1 Statutory Documents...

More information

Injury Prevention and Ergonomics Manual Health & Safety

Injury Prevention and Ergonomics Manual Health & Safety Rev Document Number Author Approver / BFO Approver Signature Issue Date Page 1 OP-MAN-00041 D Christie-Down Manager Regional 28/06/2018 1 of 14 TABLE OF CONTENTS 1 Purpose and Scope...3 2 Manual Handling...

More information

TECHNICAL INFORMATION SHEET 17. Revision 1 : 2016 MODEL RISK ASSESSMENT FOR THE MANUAL HANDLING OF GAS CYLINDERS

TECHNICAL INFORMATION SHEET 17. Revision 1 : 2016 MODEL RISK ASSESSMENT FOR THE MANUAL HANDLING OF GAS CYLINDERS TECHNICAL INFORMATION SHEET 17 Revision 1 : 2016 MODEL RISK ASSESSMENT FOR THE MANUAL HANDLING OF GAS CYLINDERS Copyright 2016 by British Compressed Gases Association. First printed 2009. All rights reserved.

More information

GUIDELINE for MSD Hazard Control Measures

GUIDELINE for MSD Hazard Control Measures APPENDIX C GUIDELINE for MSD Hazard Control Measures This MSD Control Measures guideline document will help you eliminate or reduce musculoskeletal disorder hazards identified by the MSD Hazard ID Form.

More information

MANUAL HANDLING CODE OF PRACTICE

MANUAL HANDLING CODE OF PRACTICE MANUAL HANDLING CODE OF PRACTICE 1. Introduction For some years national statistics have shown that more than a quarter of accidents reported are associated with the manual handling of loads. Sprains and

More information

One Direct Manual Handling Guidance

One Direct Manual Handling Guidance Author Version V1 One Direct Health and Safety Date Issued December 2016 Review Date May 2018 What s the problem? Incorrect manual handling is one of the most common causes of injury at work. It causes

More information

Health & Safety and Employment Law

Health & Safety and Employment Law Health & Safety and Employment Law Manual Handling Health and safety training for employees The definition of Manual Handling The transporting or supporting of a load, including the lifting, putting down,

More information

Age Concern Hounslow Manual Handling Risk Assessment PART ONE PRELIMINARY RISK ASSESSMENT

Age Concern Hounslow Manual Handling Risk Assessment PART ONE PRELIMINARY RISK ASSESSMENT Age Concern Hounslow Manual Handling Risk Assessment PART ONE PRELIMINARY RISK ASSESSMENT This checklist is to be used as a preliminary assessment of the work area. If the answer is yes or possibly, then

More information

Preventing Musculoskeletal Injuries (MSIs) in Manufacturing

Preventing Musculoskeletal Injuries (MSIs) in Manufacturing 7-Step Process to Reduce the Risk of MSI B.C. s Occupational Health and Safety Regulation requires employers to eliminate or, if that is not practicable, minimize the risk of musculoskeletal injury to

More information

Risk factors associated with pushing and pulling loads

Risk factors associated with pushing and pulling loads Risk factors associated with pushing and pulling loads There are a number of risk factors associated with pushing and pulling of loads. To make it easy to remember, it can be broken down to TILE, which

More information

List 4 Example Of How Manual Handling Risks Can Be Reduced

List 4 Example Of How Manual Handling Risks Can Be Reduced List 4 Example Of How Manual Handling Risks Can Be Reduced Risk assessment for reduced handling capacity (staff) So for example a possible risk (2) of a medium severity injury requiring 3 days away from

More information

Constructive Ideas. Assessing the risk of sprains and strains CI Introduction. Step 1: Identify hazards. What is musculoskeletal injury (MSI)?

Constructive Ideas. Assessing the risk of sprains and strains CI Introduction. Step 1: Identify hazards. What is musculoskeletal injury (MSI)? Constructive Ideas Innovative ideas to reduce soft tissue injuries in the construction in dus try! Assessing the risk of sprains and strains Introduction What is musculoskeletal injury (MSI)? Musculoskeletal

More information

Getting to grips with manual handling

Getting to grips with manual handling Health and Safety Executive Getting to grips with manual handling A short guide 2 This booklet explains the problems associated with manual handling and sets out best practice in dealing with them. The

More information

SAFE MANUAL HANDLING OPERATIONS

SAFE MANUAL HANDLING OPERATIONS SAFE MANUAL HANDLING OPERATIONS STFC Safety Code No 12 Rev. 1.5, Issued August, 2017 Note - This document may have been superseded by a more recent version. Revisions 1 Initial Launch November 2007 1.1

More information

MSD Risk Assessment Checklist

MSD Risk Assessment Checklist MSD Risk Assessment Checklist Purpose This MSD Risk Assessment Checklist is designed to provide you with a relatively quick and easy way to more formally assess the risk associated with exposures to some

More information

Manual handling at work

Manual handling at work Manual handling at work A brief guide Introduction This leaflet describes what you, as an employer, may need to do to protect your employees from the risk of injury through manual handling tasks in the

More information

Chapter 13: Manual Handling

Chapter 13: Manual Handling Chapter 13: Manual Handling Learning Outcomes: 1. Define the term manual handling, 2. Know the activities involve manual handling, 3. Know types of injuries caused by manual handling, 4. Know the risk

More information

HEALTH AND SAFETY GUIDANCE NOTE MANUAL HANDLING

HEALTH AND SAFETY GUIDANCE NOTE MANUAL HANDLING HEALTH AND SAFETY GUIDANCE NOTE MANUAL HANDLING INTRODUCTION Manual handling is interpreted as the transporting or supporting of any load (which also includes a person or an animal). It involves a variety

More information

Health and Safety Services. Safety Guide 37. Manual Handling. Facilities Management Directorate

Health and Safety Services. Safety Guide 37. Manual Handling. Facilities Management Directorate Health and Safety Services Safety Guide 37 Manual Handling Facilities Management Directorate Safety Guide 37 Manual Handling Manual Handling Contents Summary... ii Manual handling assessment flow chart...iii

More information

Safety Toolkit and Short Guide to General Application Regulations 2007 Manual Handling Section. Manual Handling

Safety Toolkit and Short Guide to General Application Regulations 2007 Manual Handling Section. Manual Handling Manual Handling Section Manual Handling Introduction Safety Toolkit The objective of the Toolkit is to provide guidance on the prevention of accidents or ill health at work and to provide a practical tool

More information

Manual handling assessment charts (the MAC tool) Introduction DRAFT

Manual handling assessment charts (the MAC tool) Introduction DRAFT Manual handling assessment charts (the MAC tool) This is a web-friendly version of leaflet INDG383(rev1), published 01/14 Introduction Work-related musculoskeletal disorders (MSDs), including manual handling

More information

Getting to grips with manual handling A short guide

Getting to grips with manual handling A short guide Getting to grips with manual handling A short guide This booklet explains the problems associated with manual handling and sets out best practice in dealing with them. The advice is intended for managers

More information

BASICS OF MANUAL HANDLING SAMPLE COURSE HANDBOOK. HSM Safety Management

BASICS OF MANUAL HANDLING SAMPLE COURSE HANDBOOK. HSM Safety Management BASICS OF MANUAL HANDLING COURSE HANDBOOK THIS PAGE INTENTIONALLY LEFT BLANK BASICS OF MANUAL HANDLING COURSE HANDBOOK FIRST EDITION 2011 C. N. PERRY MBA PgD CMIOSH AIIRSM RMaPS NOTE: The legislation and

More information

How volunteer organisations can comply with the model Work Health and Safety Act LEGISLATIVE FACT SHEET SERIES

How volunteer organisations can comply with the model Work Health and Safety Act LEGISLATIVE FACT SHEET SERIES How volunteer organisations can comply with the model Work Health and Safety Act LEGISLATIVE FACT SHEET SERIES Overview This fact sheet provides information about what volunteer organisations need to do

More information

Manual Handling Risk Assessment Procedure (HS.1.09)

Manual Handling Risk Assessment Procedure (HS.1.09) LTD Manual Handling Risk Assessment Procedure () MANUAL HANDLING RISK ASSESSMENT GUIDANCE NOTE Contents Section 1: Introduction Section 2: Risk Assessment Section 3: General Guidelines Section 4: Team

More information

Tailgate Topic Review

Tailgate Topic Review [PP 03/04/2018-03/17/2018] Lifting/Carrying/MH Lifting/Walking CONSTRUCTION INSPECTOR, 7291 (Specifications) Physical Requirements: Strength to perform average lifting up to 15 pounds and occasionally

More information

Workplace Safety Inspection Sheet

Workplace Safety Inspection Sheet Workplace Safety Inspection Sheet Record all details of a safety inspection carried out at your workplace 1 of 2 Date and Time of Inspection:... Area or workplace inspected:... Name(s) and signature(s)

More information

Chapter 13: Manual Handling

Chapter 13: Manual Handling Chapter 13: Manual Handling Learning Outcomes: After successful studying this chapter, You should be able to: 1. Define the term manual handling, 2. Know the activities involved in manual handling, 3.

More information

Horizon Care and Education Group Limited MANUAL HANDLING POLICY

Horizon Care and Education Group Limited MANUAL HANDLING POLICY Purpose. The purpose of the policy is outline ensure that Horizon Care and Education Group meets it Health and Safety obligations, under Manual Handling Operations Regulations 1992. Scope The policy applies

More information

EHS Workplace Inspection Checklist (Ref. SOP QMS-080; EHS-010)

EHS Workplace Inspection Checklist (Ref. SOP QMS-080; EHS-010) (Ref. SOP QMS-080; EHS-010) Form-445 Inspected by: Date of inspection Date of Report Report # Pages Area Manager: Area Inspected: General This EHS Workplace Inspection was conducted by: Scope of the Inspection:

More information

Hazard Identification and Risk Management

Hazard Identification and Risk Management Hazard Identification and Risk Management Australian Workcover Authorities [supported by the Company] currently use a risk management approach in developing their legislative controls. This means that:

More information

Soteria Strains. Safe Patient Handling and Mobility Program Guide

Soteria Strains. Safe Patient Handling and Mobility Program Guide Soteria Strains Safe Patient Handling and Mobility Program Guide Section 4 Special Considerations Section 4.1 - Emergency Situations V1.0 edited July 20, 2015 A provincial strategy for healthcare workplace

More information

Health and Safety Manual Handling Risk Assessment

Health and Safety Manual Handling Risk Assessment Health and Safety Manual Handling Risk Assessment 2014 City of Glasgow College Charity Number: SC0 36198 Page 1 of 14 Table of Contents 1. Purpose... 3 2. Scope... 3 3. Responsibility... 3 4. Manual Handling

More information

1 P a g e. Moving & Handling Procedure. Title: Reference No: Procedure 01. Assistant Chief Officer. Ian Plummer, Health & Safety Manager

1 P a g e. Moving & Handling Procedure. Title: Reference No: Procedure 01. Assistant Chief Officer. Ian Plummer, Health & Safety Manager Title: Moving & Handling Procedure Reference No: Procedure 01 Owner: Author Assistant Chief Officer Ian Plummer, Health & Safety Manager First Issued On: Latest Issue Date: August 2016 Operational Date:

More information

Low Medium High Critical Business Impact: X Changes are important, but urgent implementation is not required, incorporate into your existing workflow.

Low Medium High Critical Business Impact: X Changes are important, but urgent implementation is not required, incorporate into your existing workflow. Page: 1 of 10 Reviewed: 10/02/2017 Amended: 13/02/2017 CC22 - Moving and Handling Policy and Procedure Category: Care Management Sub-category: Care Practice Policy Review Sheet Review Date: 10/02/17 Policy

More information

MSD RISK ASSESSMENT. Risk Factor "Potential Risk" "High Risk" Contact Stress Repetition Grip Force Lift/Lower Force Awkward Posture Vibration WSPS.

MSD RISK ASSESSMENT. Risk Factor Potential Risk High Risk Contact Stress Repetition Grip Force Lift/Lower Force Awkward Posture Vibration WSPS. Job or Task: Date: Completed by: Once a potential risk of a musculoskeletal disorder (MSD) has been identified, the purpose of this risk assessment is to determine if a high risk of injury exists. We recommend

More information

LEAFLET 4 MANUAL HANDLING

LEAFLET 4 MANUAL HANDLING LEAFLET 4 MANUAL HANDLING AMENDMENT RECORD Amnd No Date Text Affected Authority and Date 001 11 May 10 Annex E, para 3 Corrected reference to Annex B SSDC Safety3 11 May 10 REVISION NOTE Leaflet 4, Manual

More information

Naval Facilities Engineering Command Ergonomic Risk Assessment for Aircraft Maintenance Department

Naval Facilities Engineering Command Ergonomic Risk Assessment for Aircraft Maintenance Department Naval Facilities Engineering Command Ergonomic Risk Assessment for Aircraft Maintenance Department Introduction This report summarizes the ergonomic risk assessment conducted at the Aircraft Maintenance

More information

Manual Handling Policy

Manual Handling Policy Manual Handling Policy Version No V1.0 DRAFT Author Date Comments Approved by Bridget Meats 2-10-15 Recommended for Approval by H&S Group V1.0 29-10-15 APPROVED For approval by QRC V2.0 13-10-16 Recommended

More information

SAFE WORK METHOD STATEMENT

SAFE WORK METHOD STATEMENT SAFE WORK METHOD STATEMENT AUGER / POST HOLE DIGGER Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES

More information

This guidance note gives simple, practical advice on what can be done to eliminate or reduce the risks.

This guidance note gives simple, practical advice on what can be done to eliminate or reduce the risks. Health and Safety Guidance Note MANUAL HANDLING A guide for Managers, Heads of Departments Introduction Manual handling operations currently account for approximately 35% percent of all reported industrial

More information

Manual Handling October 2014

Manual Handling October 2014 Manual Handling October 2014 How Are We Doing? LTI s 0 in last 12 months Period Location Oil & Gas Base AFR Oil & Gas Sites AFR Total AFR September 0 0 0 12 Month Rolling 0 1.59 1.45 Statistics presented

More information

GENERAL WORK HEALTH & SAFETY CHECKLIST INTENDED USE. St Euphemia College - General Work Health and Safety Checklist

GENERAL WORK HEALTH & SAFETY CHECKLIST INTENDED USE. St Euphemia College - General Work Health and Safety Checklist GENERAL WORK HEALTH & SAFETY CHECKLIST INTENDED USE This document is a summary checklist intended for employees as well as the School executive, and sets out the measures that a PCBU should put in place

More information

NEW EMPLOYEE ERGONOMIC WORKSHEET

NEW EMPLOYEE ERGONOMIC WORKSHEET NEW EMPLOYEE ERGONOMIC WORKSHEET DIRECTIONS New Employee: This document has been prepared to assist you and your supervisor in determining some of the items that you may need. After you have had an opportunity

More information

EMPLOYER - PHYSICAL DEMANDS ANALYSIS Lab Technician

EMPLOYER - PHYSICAL DEMANDS ANALYSIS Lab Technician EMPLOYER - PHYSICAL DEMANDS ANALYSIS Lab Technician Job Title: Lab Technician Video Link: Work Schedule: http://youtu.be/giggsz7hm (You Tube) http://albertaforestproducts.ca/our-industry/healthsafety/physical-demands-analyses-pda

More information

Occupational Health & Safety

Occupational Health & Safety Personal Development Level 3 Occupational Health & Safety Any injury particularly workplace injury is a major cause of concern for all involved in Occupational Health and Safety (OHS). The factors which

More information

The Management of Hazardous Manual Handling Operations. The Management of Health and Safety at Work Regulations

The Management of Hazardous Manual Handling Operations. The Management of Health and Safety at Work Regulations Number MS - 09 The Management of Hazardous Manual Handling Operations Scope Law This document provides the information necessary to identify and manage hazardous manual handling activities. The Management

More information

Meet Today s Webinar Team

Meet Today s Webinar Team Meet Today s Webinar Team Moderator: Stacy Rose, CSP Stacy is a certified professional with 16 years experience in workplace safety. Stacy holds a bachelor s in industrial engineering and a master s in

More information

Control of Vibration at Work

Control of Vibration at Work Control of Vibration at Work 1) POLICY University of Glasgow will put in place measures to protect employees from the risks of Hand Arm Vibration Syndrome (HAVS) and Whole Body Vibration. These measures

More information

SAMPLE MANUAL HANDLING CODE OF PRACTICE

SAMPLE MANUAL HANDLING CODE OF PRACTICE SAMPLE MANUAL HANDLING CODE OF PRACTICE Company: Workplace Address: Introduction This code sets out requirements that this company will follow for the reduction of MSIs due to manual handling at this workplace.

More information

The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field.

The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Purpose The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Manual Material Handling Manual material handling

More information

Manual Handling - Theory

Manual Handling - Theory Manual Handling - Theory Manual Handling can be defined as any transporting, supporting of a load, lifting, pushing, putting down, pulling, carrying or moving of any load. The load includes a person, it

More information

Job: Wheat Specialty Description: Loads grain into ships hatches and levels off load Equipment Assessed: AGT semi-automated operation and PECO at JRI

Job: Wheat Specialty Description: Loads grain into ships hatches and levels off load Equipment Assessed: AGT semi-automated operation and PECO at JRI Job: Wheat Specialty Description: Loads grain into ships hatches and levels off load Equipment Assessed: AGT semi-automated operation and PECO at JRI ESSENTIAL DUTIES 1. Loading Grain A. Semi-Automated

More information

Manual Handling Safety Procedure

Manual Handling Safety Procedure Pars Oil & Gas Company Manual Handling Safety Procedure HEALTH, SAFETY AND ENVIRONMENT PROCEDURE Manual Handling Safety Procedure DOCUMENT ID - PR-26-POGC-001 REVISION 0.0 Pars Oil & Gas Company Pages

More information

Environmental Health & Safety Programs

Environmental Health & Safety Programs 1.0 Introduction Material handling accounts for approximately 25% of all occupational injuries. Common injuries include strains, sprains, fractures, and bruises. The largest number of injuries occur to

More information

Z.A.C. Incorporation

Z.A.C. Incorporation Ergonomic Safety Checklist conducted for Z.A.C. Incorporation Date and Time of Inspection 28 May 2018 11:32 AM Inspected by Grace Joan Tan Location 1 Dinso Rd, Khwaeng Wat Bowon Niwet, Khet Phra Nakhon,

More information

Job: Dock Gantry Operator Description: Operates the Dock Gantry Equipment Assessed: VanTerm Dock Gantry ESSENTIAL DUTIES

Job: Dock Gantry Operator Description: Operates the Dock Gantry Equipment Assessed: VanTerm Dock Gantry ESSENTIAL DUTIES Job: Dock Gantry Operator Description: Operates the Dock Gantry Equipment Assessed: VanTerm Dock Gantry ESSETIAL DUTIES 1. Operating the Dock Gantry A) Sitting B) Handling Controls C) Operating Foot Pedals

More information

OFFICE SAFETY ESSENTIALS

OFFICE SAFETY ESSENTIALS OFFICE SAFETY ESSENTIALS Introduction Health and Safety at work is everyone's responsibility. It is important that you have a general understanding of safety and health The employer must ensure that your

More information

WORK HEALTH AND SAFETY

WORK HEALTH AND SAFETY Employees in South Australia are protected by and required to adhere to State & National health and safety regulations. Employers, employees and others all have an important role to play. For further information

More information

Manual handling assessment charts (the MAC tool)

Manual handling assessment charts (the MAC tool) Manual handling assessment charts (the MC tool) Introduction Work-related musculoskeletal disorders (MSDs), including manual handling injuries, are the most common type of occupational ill health in the

More information

BRIT TEAM PLATEFORM Training Module List

BRIT TEAM PLATEFORM Training Module List BRIT TEAM PLATEFORM Training Module List Fleet Safety Accident Scene Management Every day, drivers are involved in motor vehicle emergencies and accidents. The goal of this training program is to instruct

More information

Potential hazards People at risk and how? Actions already in place Further action required Action by

Potential hazards People at risk and how? Actions already in place Further action required Action by Risk Assessment Flat Roof Repair Prepared by Oracle Managed Services For: BAM FM On: 24/02/2017 Review date: N/A Potential hazards People at risk and how? Actions already in place Further action required

More information

Workplace Health. and. Safety

Workplace Health. and. Safety Workplace Health and Safety Page 1 of 36 CEIL Motive Power Pty Ltd Workplace Health and Safety Workplace Health and Safety Page 2 of 36 Table of Contents Introduction... 3 Risk Management... 3 Risk Assessment

More information

Job Hazard Analysis (JHA) What is Job Hazard Analysis (JHA)?

Job Hazard Analysis (JHA) What is Job Hazard Analysis (JHA)? Job Hazard Analysis (JHA) How to Analyze Health & Safety Hazards at your worksite Michael Hall, Director CA EH+S TRAINING CENTER 1 What is Job Hazard Analysis (JHA)? It is a method for systematically identifying

More information

Induction SGAC - EVENTS -

Induction SGAC - EVENTS - Induction SGAC - EVENTS - 1 P a g e CONTENTS CONTENTS... 2 WELCOME... 3 VISITING SGAC... 3 EMERGENCY PROCEDURES... 3 Warning Tones:... 4 It Is Important You Know The Location Of:... 4 If You Discover Smoke

More information

SAFE WORK METHOD STATEMENT

SAFE WORK METHOD STATEMENT SAFE WORK METHOD STATEMENT WATER PUMP - PETROL Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES

More information

HMCL211. Session 1. Work Health And Safety. Regulations, Risk Management, Ergonomics & Manual Handling. Department of Naturopathic Medicine

HMCL211. Session 1. Work Health And Safety. Regulations, Risk Management, Ergonomics & Manual Handling. Department of Naturopathic Medicine HMCL211 Session 1 Work Health And Safety Regulations, Risk Management, Ergonomics & Manual Handling Department of Naturopathic Medicine endeavour.edu.au o o o o o o o o o Work Health & Safety Session 1

More information

WORK METHOD STATEMENT CARPET LAYING

WORK METHOD STATEMENT CARPET LAYING ORGANISATION DETAILS Organisation Name: Gedoun Constructions Pty Ltd Contact Name: Joe Gedoun ACN/ABN: 52 284 873 581 Contact Position: Director Address: PO Box 1138, Townsville QLD 4810 Contact Phone

More information

HAZARD RECOGNITION EVALUATION and CONTROL

HAZARD RECOGNITION EVALUATION and CONTROL What is a hazard? HAZARD RECOGNITION EVALUATION and CONTROL Hazard - a dangerous object, event, behaviour or condition (in the workplace) which has the potential to cause injury, illness or property damage.

More information

Slips, Trips and Falls

Slips, Trips and Falls This document is intended to provide basic safety guidelines for the Physical Plant Department at Community College of Allegheny County. The information provided in this guide may vary by site. Version

More information

PAC. Risk Management Resources. The cost of Workers Compensation can be controlled. Also visit WELLAdvised

PAC. Risk Management Resources. The cost of Workers Compensation can be controlled. Also visit   WELLAdvised PAC Risk Management Resources The cost of Workers Compensation can be controlled Also visit www.babbins.com WELLAdvised Safety Guidelines for Home Visits 1) Do not give consumers your home phone number.

More information

A Health and Safety Tip Sheet for School Maintenance Staff. Did you know? Step 1. Identify job hazards. Step 2. Work towards solutions

A Health and Safety Tip Sheet for School Maintenance Staff. Did you know? Step 1. Identify job hazards. Step 2. Work towards solutions INSPECTION Health and CHECKLIST Safety Committees MAINTAINING SAFETY: A Health and Safety Tip Sheet for School Maintenance Staff 1 Maintenance and facilities staff members keep schools operational, safe,

More information

Safety Guidelines for Live Entertainment and Events I Part 2. Hazard Identification and Risk Management 1

Safety Guidelines for Live Entertainment and Events I Part 2. Hazard Identification and Risk Management 1 Safety Guidelines for Live Entertainment and Events Part 2. Hazard Identification and Risk Management Contents Disclaimer... 1 1. Principles of Risk Management... 2 2. The Risk Management Process... 2

More information

Manual Handling Risk Assessment In accordance with the Manual Handling Operations Regulations 1992

Manual Handling Risk Assessment In accordance with the Manual Handling Operations Regulations 1992 Ref o MHRA 3.1 Task Carrying Bin Bags Location Bath Area ame of Assessor Simon Foley Job Title Quality Health and Environmental Manager Signature 28 th ovember 2014 Review Details (Reviewed following change

More information

WorkWell Consulting Ergonomic Risk Identification & Assessment. Job Title: Equipment Operator III (Sweeper) Elgin Ford #2108 Date: September 17, 2003

WorkWell Consulting Ergonomic Risk Identification & Assessment. Job Title: Equipment Operator III (Sweeper) Elgin Ford #2108 Date: September 17, 2003 TASK ANALYSIS WORKSHEET Company: The Corporation of Delta Department: Engineering Operations Job Title: Equipment Operator III (Sweeper) Elgin Ford #208 Date: September 7, 2003 Job Summary: The Sweeper

More information

HEALTH & SAFETY GUIDANCE FOR MANAGERS MINIMUM SPECIFICATIONS REQUIRED FOR OFFICE FURNITURE AND DISPLAY SCREEN EQUIPMENT (DSE)

HEALTH & SAFETY GUIDANCE FOR MANAGERS MINIMUM SPECIFICATIONS REQUIRED FOR OFFICE FURNITURE AND DISPLAY SCREEN EQUIPMENT (DSE) HEALTH & SAFETY GUIDANCE FOR MANAGERS MINIMUM SPECIFICATIONS REQUIRED FOR OFFICE FURNITURE AND DISPLAY SCREEN EQUIPMENT (DSE) TRAINING Managers need to ensure that any of their staff who are classed as

More information

The Sample Company Pty Ltd

The Sample Company Pty Ltd Job Safety and Environmental Analysis (JSEA) / Safe Work Method Statement (SWMS) Part 1: Project and Task Identification Process Initiators of SWMSs are responsible for consulting the Project Supervisor,

More information

New Employee Safety Orientation. Session Objectives. Session Objectives (cont.)

New Employee Safety Orientation. Session Objectives. Session Objectives (cont.) New Employee Safety Orientation Session Objectives Understand your role in safety and security Get safety information Identify and report safety hazards Prevent and respond to fires Respond to accidents

More information

HEALTH AND SAFETY GUIDANCE NOTE HAND-ARM VIBRATION

HEALTH AND SAFETY GUIDANCE NOTE HAND-ARM VIBRATION HEALTH AND SAFETY GUIDANCE NOTE HAND-ARM VIBRATION INTRODUCTION Exposure to high levels of vibration can cause longterm painful damage to your hands and fingers. The Control of Vibration at Work Regulations

More information

MSD Hazard Identification Tool: Option 2

MSD Hazard Identification Tool: Option 2 MSD Hazard Identification ool: Option 2 his MSD Hazard Identification ool is provided to help you identify jobs or tasks that have MSD hazards, where workers may be at an increased risk of developing an

More information

SAFE WORK METHOD STATEMENT

SAFE WORK METHOD STATEMENT SAFE WORK METHOD STATEMENT LOADING AND UNLOADING VEHICLES Prepared for Client: Rural Construction & Maintenance Pty Ltd Project No: 1 Site: 660 Great Ocean Road, Bellbrae Date Prepared: 29/07/2015 1. RESPONSIBILITIES

More information

Ergonomic Analysis for XYZ Products

Ergonomic Analysis for XYZ Products Ergonomic Analysis for XYZ Products A work site evaluation was conducted for Production Worker in Department #213 on 05/31/05. The purpose of this analysis was to identify risk factors for Musculoskeletal

More information

Office Ergonomics Standard

Office Ergonomics Standard This standard outlines general workstation and work practices to be followed in order to reduce the risk factors for developing musculoskeletal injuries (MSIs) and visual strain from working at computer

More information

Safety Checklist for Events Held at Hillbrook

Safety Checklist for Events Held at Hillbrook Safety Checklist for Events Held at Hillbrook Hazards/ Issues or Tasks 1. EVENT ACCESS AND EGRESS Entry / Exit areas are kept clear and accessible. For an evening event, that you have appropriate Lighting.

More information

WORK ENVIRONMENT SAFETY. Body Mechanics. Electrical Safety. Employee. Safety. Fall. Needlestick Prevention. Safety

WORK ENVIRONMENT SAFETY. Body Mechanics. Electrical Safety. Employee. Safety. Fall. Needlestick Prevention. Safety WORK ENVIRONMENT SAFETY Electrical Safety Employee Safety Body Mechanics Fall Safety Needlestick Prevention Rev.: bw/january 2016 COMMON INJURIES AND ACCIDENTS Slips, trips and falls Back injuries Ergonomic

More information

Formwork Labourer Initial work capacity form

Formwork Labourer Initial work capacity form Purpose of this form Formwork Labourer This form is designed to be completed by injured workers and their supervisors and/or the return to work coordinator, if applicable; to determine the tasks the worker

More information

Operation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039. Name Date Signature. Author Jarred Hearle 27/11/2015

Operation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039. Name Date Signature. Author Jarred Hearle 27/11/2015 Operation of Embrey Excavator Shears Safe Work Procedure PTES_HSE_SWP_039 Name Date Signature Author Jarred Hearle 27/11/2015 Reviewed FMG Site Team 27/11/2015 ---------- Approved Geoff Selfe 27/11/2015

More information

Process Name Material Handling/MSD Prevention Program

Process Name Material Handling/MSD Prevention Program CNM WAY PROCESS CNM Process Name Material Hanling/MSD Prevention Program (04/10/2018 Revision) Overview of Material Hanling/MSD Prevention Program Purpose: To provie a safe an healthy working environment

More information

THERMAL COMFORT GUIDELINES

THERMAL COMFORT GUIDELINES UOW SAFE@WORK THERMAL COMFORT GUIDELINES HRD-WHS-GUI-244.6 Thermal Comfort Guidelines 2016 July Page 1 of 8 Contents 1 Introduction... 3 2 Responsibilities... 3 2.1 Managers... 3 2.2 Supervisors... 3 2.3

More information

Accident Investigation and Hazard Analysis

Accident Investigation and Hazard Analysis Accident Investigation and Hazard Analysis June 18, 2015 Objectives: Accident Investigation Define accidents Review why accident investigations are important Review the purpose of accident investigations

More information

Prevention of Falls and Working at Heights

Prevention of Falls and Working at Heights Workplace Safety Schools Cleaning Prevention of Falls and Working at Heights It is the policy of the Company to avoid working at heights above 2 metres wherever practical. When avoidance is not an option,

More information

Naval Facilities Engineering Command. Ergonomics Risk Assessment for. Dinghy Retrieval and Storage

Naval Facilities Engineering Command. Ergonomics Risk Assessment for. Dinghy Retrieval and Storage Naval Facilities Engineering Command Ergonomics Risk Assessment for Dinghy Retrieval and Storage Introduction This report summarizes the ergonomics risk assessment conducted on November 16 th, 2006. The

More information

SAFE WORK PROCEDURE LOCATION WRITTEN BY APPROVED BY DATE CREATED LAST REVISION. All Schools Lorie Carriere Physical Therapists April 25, 2017 new

SAFE WORK PROCEDURE LOCATION WRITTEN BY APPROVED BY DATE CREATED LAST REVISION. All Schools Lorie Carriere Physical Therapists April 25, 2017 new Page 1 of 6 LOCATION WRITTEN BY APPROVED BY DATE CREATED LAST REVISION All Schools Lorie Carriere Physical Therapists April 25, 2017 new PERSONAL PROTECTION EQUIPMENT (PPE) OR DEVICES Appropriate footwear

More information

Hazard Management Making your workplace safer

Hazard Management Making your workplace safer Hazard Management Making your workplace safer A Guide to Hazard Identification, Risk Assessment, Control and Reviewing 1 What is a hazard? A hazard is something which has the potential to harm the health,

More information

QUEENSLAND UNIVERSITY OF TECHNOLOGY

QUEENSLAND UNIVERSITY OF TECHNOLOGY QUEENSLAND UNIVERSITY OF TECHNOLOGY SITE SPECIFIC SAFETY MANAGEMENT PLAN FOR SAMFORD HOUSE SAMFORD ECOLOGICAL RESEARCH FACILITY SAMFORD VALLEY 2007 Dylan Randall SN: 06305466 dylan.randall@student.qut.edu.au

More information

Safety Services. Local Rules for Safety in Manual Handling Operations

Safety Services. Local Rules for Safety in Manual Handling Operations Safety Services Local Rules for Safety in Manual Handling Operations Last Review Date: 10 October 2012 Approved 23 June 2009 CONTENTS 1. Introduction 2. Responsibilities of Heads of Department 3. Responsibilities

More information