10.1 Main Unit. INDEPENDENT WHOLESALE WELDING SUPPLY Ph: Fax: Website:

Transcription

1 10.1 Main Unit

2 10.1 Main Unit 1 Case Cross feed holder Cross feed liner Handle Fan cover Bottom plate Heat shield Heat shield collar Idle wheel unit Idle wheel bracket Roller shaft Roller Washer Screw (SM-5X25) 6C Idle wheel Collar (A) Bearing retainer Collar (B) Drive wheel shaft w/key Collar (C) Drive wheel Worm wheel Clutch Washer Screw (SM-5X15) 6C Screw (SP-5X8) 6C Bearing (6300ZZ) Bearing (6302ZZ) Stop ring (STW-15) 6B Clutch lever assembly Slider Clutch spring Worm shaft assembly Worm spring Speed adjusting shaft Speed adjusting bracket Rack Speed adjusting handle Speed adjusting knob Speed adjusting cone assembly 41 Cone spring Motor disk Motor (230V-240) Bearing (608ZZ) Cross feed pinion unit Spring pin (PR-2.5X16) 6B Handle (Ø 40) Pinion metal Pinion Wing bolt (BS-6X15) 6C Wing bolt (BS-6X25) 6C Hexagon bolt (BH-6X30) 6C Hexagon bolt (BH-6X18) 6C Screw (SP-6X14) 6C Screw (SP-5X15) 6C with washer 56 Screw (SP-4X10) 6C Screw (SP-4X15) 6C Screw (SP-4X8) 6C Motor fan w/screw

3 10.2 Electrical, gas and torch slide holder units

4 10.2 Electrical, gas and torch slide holder units 1 Panel assembly (200V-240V) 2 Panel Cap for dust protector Nut for dust protector Metal socket (3P) Switch (200V-240V) Condenser (230V-240V) Terminal (200V-240V) 4P Screw (SM-3X6) 6C Screw (SM-3X8) with nut 6C Screw (SP-3X6) with nut 6C Condenser fi xing plate Faston terminal Screw (SP-4X8) 6C Torch holder assembly Torch holder Torch holder fi xing plate Holder fi xing handle Rack bar Handle (Ø 40) Pinion metal Pinion Spring pin (PR-2.5X16) 6B Hexagon bolt (BC-5X14) 6C Screw (SP-6X25) 6C Distributor () Screw (SM-5X25) 6C Hose for oxygen () OXY Hose for gas - ACET ACET600 1 Hose for gas - LPG LPG Nut oxygen RHN 1 31 Nut for fuel gas LHN 1 32 Hose connector oxy NP 1 33 Hose connector fuel gas NP 1 34 Torch - 3 seat tips (KE) KT 1 Torch - 2 seat tips CT 1 (CW) 35 Tip fixing nut Rack w/screw Valve for preheat oxygen Valve for gas Valve for jet for oxygen O-ring Rubber plug Earth clip Metal plug 3P Cabtyre cord assemply 3P

5 10.3 Two Torch Unit

6 10.3 Two Torch Unit 1 Torch holder assembly Torch holder Screw (SP-6X25) Torch up/down handle Handle (Ø 40) Pinion metal Pinion Spring pin (PR-2.5X16) Torch cross feed holder Cross feed holder Wing bolt Crank handle Cross feed pinion unit Handle (Ø 40) Pinon metal Pinion Spring pin (PR-2.5X16) 6B Rack bar Distributor () N/A Distributor Y-Oxy R/H IWR121 1 N/A Distributor Y-Fuel Gas L/H IWR Fitting Weight supporter Screw (SM-5X55) 6C Hexagon bolt (BH-10X35) 6C Nut for oxygen RHN 1 25 Hose connector oxy NP 1 26 Nut for fuel gas LHN 1 27 Hose connector gas NP 1 28 Torch - 3 seat tips (KE) KT 2 Torch - 2 seat tips (CW) CT 2 29 Weight Hexagon bolt (BH-6X40) 6C Hose for oxygen OXY Hose for gas - ACET ACET600 1 Hose for gas - LPG LPG Hose for oxygen OXY Hose for gas - ACET ACET600 1 Hose for gas - LPG LPG600 1

7 Wiring diagram Assembly drawing of CG-12 Beetle

8 106 (Standard Speed) for Propane Metric System Plate Thickness (mm) Tip Size Cutting Speed (mmv min) Cutting Oxygen Pressure (kg/cm 2 ) / (Mpa) Pr-Heat Fuel Gas Pressure (kg/cm 2 ) / (Mpa) Kerf Width (mm) / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Inch System Plate Thickness (inches) Tip Size Cutting Speed (mmv min) Cutting Oxygen P.S.I.G Pr-Heat Fuel Gas P.S.I.G Kerf Width (inches) 1/ / / / / / / Note: 1. All pressures are torch inlet pressures 2. Oxygen purity is minimum of 99.7%, propane is minimum of JIS Grade 3 3. Depending on the surface condition of the steel plate (scale, paint) either increase the fuel gas pressure or decrease cutting speed. Also, when precision cutting is required, adjust all date.

9 102-D7 (High Speed) for Acetylene Metric System Plate Thickness (mm) Tip Size Cutting Speed (mmv min) Cutting Oxygen Pressure (kg/cm 2 ) / (Mpa) Pr-Heat Fuel Gas Pressure (kg/cm 2 ) / (Mpa) Kerf Width (mm) / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Inch System Plate Thickness (inches) Tip Size Cutting Speed (mmv min) Cutting Oxygen P.S.I.G Pr-Heat Fuel Gas P.S.I.G Kerf Width (inches) 1/ / / / / / / Note: 1. All pressures are torch inlet pressures 2. Oxygen purity is minimum of 99.7%, propane is minimum of JIS Grade 3 3. Depending on the surface condition of the steel plate (scale, paint) either increase the fuel gas pressure or decrease cutting speed. Also, when precision cutting is required, adjust all date.