Bubble Augmented Propulsion with a Convergent-Divergent Nozzle

Size: px
Start display at page:

Download "Bubble Augmented Propulsion with a Convergent-Divergent Nozzle"

Transcription

1 30 th Syposiu on Naval Hydrodynaics Hobart, Tasania, Australia, -7 Noveber 014 Bubble Augented Propulsion with a Convergent-Divergent Nozzle Jin-Keun Choi, Xiongjun Wu, and Georges L. Chahine (DYNAFLOW, INC., U.S.A.) ABSTRACT Augenting the thrust of a waterjet through bubble injection has been a subject of interest for any years, particularly for the purpose of boosting thrust teporarily, as in the case of planning hulls or seiplanning ships to overcoe the hup speed. In our previous work using a divergent-convergent 3D nozzle, we have shown that net thrust augentation increases with the injected air volue fraction, and we were able to easure up to 70% augentation for a void fraction of 50%. As the void fraction in the bubbly ixture increases the speed of sound drops significantly and the ixture velocity could drop below the speed of sound leading to a need to investigate choked or supersonic ixture flow in the nozzle. In the present study, a convergent-divergent nozzle was designed, built, and tested to investigate experientally if choked flow in the nozzle can actually be reached at high void fractions and to easure thrust gain for choked supersonic conditions. In parallel, a nuerical study was conducted for the new nozzle geoetry using an Eulerian-Lagrangian two-way coupled approach. The nuerical predictions recovered observed unsteady clustering and stratification of bubble clouds in the nozzle weakly divergent section. INTRODUCTION Unlike traditional propulsion devices which are typically liited to less than 50 knots, the bubble augented propulsion concept proises thrust augentation even at very high vehicle speeds (e.g. Mor and Gany, 004)). Analytical, nuerical, and experiental evidence (Tangren et al., 1949, Muir and Eichhorn, 1963, Ishii et al., 1993, Kaeda and Matsuoto, 1995, Wang and Brennen, 1998, Preston et al., 000, Albagli and Gany, 003, Mor and Gany, 004, Chahine et al., 008, Wu et al., 010, 01a, 01b, Gany and Gofer, 011) showing that bubble injection can significantly iprove the net thrust of a water jet ake the idea of bubble augented thrust attractive. In recent experiental studies using D and 3D divergent-convergent nozzles, we reported as high as 70% increase of net thrust augentation over a water only jet (Wu et al., 010, 01a, 01b, Singh et al., 01). These were achieved with injected air volue fractions in the range of 50%. It is well known that, with increased void fraction, the speed of sound in the bubbly ixture decreases substantially and could be as low as 0 /s (Brennen, 1995). In this case local ixture flow velocities can exceed the speed of sound in the ediu, resulting in supersonic flow and choked conditions. Existing fundaental two-phase flow studies (e.g. Singh et al., 014, Mor & Gany, 004) indicate that higher thrusts could be achieved if flow conditions with choking in the nozzle could be realized. This led us to investigate a nozzle configuration, which ay generate a choked flow. In this paper, we present the two-phase flow nozzle we designed and built, and suarize experiental studies conducted to date with this nozzle. In parallel to the experiental study, we have also extended our 3D two-phase flow nuerical ethod, 3DYNAFS, to handle higher void fractions and enable siulations at conditions approaching the choked flow. NUMERICAL METHODS In this study, we odel the bubbly ixture flow inside the nozzle by coupling Lagrangian tracking of individual bubbles and Eulerian solution of the continuu ixture flow. The bubble dynaic oscillations are in response to the variations of the ixture flow field variables, and the flow field depends directly on the tie dependent bubble size and distribution in the field. The unsteady 3D odeling is realized by coupling the Navier-Stokes solver 3DYNAFS_VIS with the bubble dynaics and tracking solver 3DYNAFS_DSM. Applications of this approach with validations were presented in Hsiao & Chahine (001, 00, 004a, 004b, 005), Chahine et al. (008), and Wu et al. (010). A recent iproveent was to use a Gaussian distribution to represent the discrete bubbles in the Eulerian description of the density (Ma et al., 014, Hsiao et al., 014). 1

2 The bubbly ixture is treated as a continuu and satisfies the following continuity and oentu equations: u0, t Du p u g, Dt (1) where, u, p are the ixture density, velocity, and pressure respectively, the subscript represents the ixture ediu, and g is the gravity body force. The ixture density and the ixture viscosity can be expressed as 1 g, 1, g () where is the local void fraction, defined as the local volue occupied by the bubbles per unit ixture volue. The subscript represents the liquid and the subscript g represents the bubbles. The continuu flow field has a space and tie dependent density siilar to a copressible liquid. The bubble dynaics is solved using the following Keller-Herring equation that includes the effect of the surrounding ediu copressibility with a Surface-Averaged Pressure (SAP) schee (Chahine, 009): R 3 R 1 RR 1 R c 3c uenc ub R R d 1 4 c c dt 3k R0 4R pv pg0 Penc R R R. (3) In the above equations, R is the bubble radius at tie t, R 0 is the initial bubble radius, is the surface tension paraeter, p v is the liquid vapor pressure, p g0 is the initial gas pressure inside the bubble, and k is the polytropic copression law constant. u enc is the bubble surface averaged ixture velocity at the bubble location, u b is the bubble travel velocity, and P enc is the bubble surface averaged pressure seen by the bubble during its travel, and c is the local speed of sound in the bubbly ixture. The bubble trajectory is obtained fro a bubble otion equation siilar to that derived by Johnson and Hsieh (1966): 3 b dub b R CD uub uub dt R u 1 du du ( ) b b ub g x dt dt Cv d uub. 1/ L ij 1/ 4 Rd ( lkdkl) (4) The right hand side of Equation (4) is coposed of various forces acting on the bubble. The first ter accounts for the drag force, where the drag coefficient C D is deterined by the epirical equation of Haberan and Morton (1953). The second and third ter in Equation (4) account for the effect of change in added ass on the bubble trajectory. The fourth ter accounts for the effect of the ediu pressure gradient, and the fifth ter accounts for the effect of gravity. The last ter in Equation (4) is the Saffan (1965) lift force due to shear as generalized by Li & Ahadi (199). The coefficient C L is.594, is the kineatic viscosity, and d ij is the deforation tensor. In the present study, the 1D steady state version of the above approach (Chahine et al., 008, Singh et al., 01) was also used for design studies. In addition, an analytical 0D odel was used to optiize the nozzle geoetry for axiu thrust enhanceent (Singh et al., 01). This approach further siplifies the equations and only requires knowledge of the areas at the inlet, the outlet and the injection section, as well as the pressure and velocity jups at the injection location. The 0D odel was extended to choked flow conditions, where the void fraction at the throat, throat, can be solved fro the following relations (Singh et al., 01, 014): 1 throat (1 throat ) A throat 1 (1 ref ) A ref 1 1 (1 ref ) * ln, ref throat (1 throat ) ref (5) where the subscript ref eans the quantities at the reference location, and A throat is the throat area. In our analysis, the reference location is taken iediately downstrea of the air injection. Once the throat void fraction is obtained by solving (5), the velocity, void fraction, and pressure at any location downstrea of the air injection can be obtained fro the continuity equation and the oentu equation. Once these flow quantities are known, the thrust for the geoetry under choked conditions can be coputed. Detail equations and procedure are described in Singh et al. (014).

3 THRUST AUGMENTATION INDICES Depending on the thrust generating nozzle application type, one of two definitions for thrust can be used (Chahine et al., 008, Wu et al. 010). For rajet type propulsion, the thrust of the nozzle is coputed as: TR pu da, A (6) where u is the axial coponent of the ixture velocity, and the surface integration is taken over a control surface, A, that encopasses both the inlet and the outlet. For waterjet type applications, the thrust of the nozzle is coputed using T o u da, W A (7) where A o is the exit surface area of the nozzle. To evaluate the perforance of a nozzle design with air injection, we define as a relative thrust augentation index as follows: Ti, Ti i, Ti i Ror W, (8) in which Ti, and Ti are thrusts with bubble injection at void fraction and without injection. We can also define a oentu thrust augentation index,, as the net thrust increase with bubble injection noralized by the inlet oentu flux, T Au, as following: inlet A throat /A inlet A exit /A inlet Table 1: Optiu geoetric ratios for different injection void fractions under choked conditions. Inlet pressure = 507 kpa (74 psi), injection area ratio Ainjection/Ainlet = 3.4. The exit area resulting for the design in Table 1 is too large for practical ipleentation and would results in flow separation unless the length of the expansion is too large. Therefore, this was relaxed and the effect of exit area was studied further. Figure 1 shows the oentu thrust gain index,, versus the nozzle inlet pressures for three non-optial fixed exit area ratios A exit /A inlet. This shows a large effect of the selected exit area on the optiu thrust gain when the inlet pressure is lower than 304 kpa (44 psi), while the effect of exit area is sall for higher inlet pressures. Thus, for high inlet pressures we can reduce the exit area ratio A exit /A inlet without sacrificing the axiu attainable thrust gain too uch. NOZZLE DESIGN STUDY T T R, R. (9) T In order to design a nozzle having the potential to generate ixture flow choking at the throat, we use first the analytic 0D ethod. This ethod depends only on the ratios of the cross sectional areas of the throat over the inlet section, A throat /A inlet, and that of the exit area over the inlet area, A exit /A inlet (Singh et al., 014). In the approach we search for the axiu of varying the contraction ratios: A throat /A inlet and A exit /A inlet for a given inlet pressure and injection area over inlet area ratio. This optiization study resulted in the optial contraction ratios shown in Table 1 (Singh et al., 014) for P inlet = 5 at, which are dependent on the void fraction. The corresponding thrust oentu gain indices are uch higher ( ) than those obtained with the subsonic nozzles (~ 0.45). Figure 1: Influence of the exit area on the oentu thrust index,, for different inlet pressures. Injection void fraction = 0.6. Injection area ratio Ainjection/Ainlet = 3.4. Before proceeding with the design, the effect of the inlet pressure on the thrust gain was reexained. Figure shows how the oentu thrust gain index changes with respect to the void fraction for different inlet pressures for a fixed injection area ratio A injection /A inlet = 3.4. Note that each point on the curves represents a different optiu nozzle for that condition. clearly increases with both the void fraction and the inlet pressure but appears to be ore sensitive to the void fraction changes than the inlet pressure changes. For instance,, increases by 74% when the void fraction changes fro 0.4 to 0.6, while it increases only 4% for = 0.6 when the inlet pressure changes fro 304 kpa (44 psi) to 507 kpa (74 psi). Figure 3 shows the inlet velocity required to achieve choked flow conditions corresponding to each optial nozzle geoetry in Figure. Choked flow 3

4 condition can be achieved with slower inlet velocities when achieving higher void fraction at injection. Considering the available pups in the facility (described later), we aied for an inlet velocity of about 5 /s, an inlet pressure of about 300 kpa (44 psi), and injection void fractions in the 50% range. We aied at achieving a of about 1.0 with the new choked flow nozzle, which is ore than twice ~ 0.45 which we could achieve with subsonic ixture flow nozzles. provides better chances of observing supersonic flow as such condition will exist along the whole length of the diverging section of the nozzle. Starting fro the optiization results in Table 1, the throat area was selected in the optiu design value range, A throat /A inlet = 1.7, however the exit area was A exit /A inlet =.9. These two area ratios need to be adjusted further to guarantee the under-expansion condition in the divergent section. Figure : The oentu thrust gain index vs. the injection void fraction for different inlet pressures. Injection area ratio Ainjection/Ainlet = 3.4. Figure 4: The predicted exit pressure of the optiu geoetry when the throat area ratio Athroat/Ainlet is varied while Aexit/Ainlet is kept at.9. Figure 5: The predicted exit pressure of the optiu geoetry when the exit area ratio Aexit/Ainlet is varied while Athroat/Ainlet is kept at 1.7. Figure 3: Inlet velocity Uinlet required for a choked flow condition vs. void fraction at injection for the optiu nozzle geoetries of Figure at different inlet pressures. Injection area ratio Ainjection/Ainlet = 3.4. Another design consideration was to aintain the supersonic flow in the entire divergent section after we achieve choked condition at the throat. Such a flow condition will result in large oentu gain at the exit, and such flow condition was iplicitly assued in the above thrust calculations. In general copressible flows in a convergent-divergent nozzle, this condition is called under-expansion, which occurs when the pressure just before the exit is higher than the abient pressure outside the exit. Under this condition, the expansion shock waves will be located outside the nozzle and not inside the divergent part of the nozzle. This design also The throat area was varied first, and the resulting exit pressure was onitored. Figure 4 shows the influence of the throat area on the exit pressure when A exit /A inlet =.9. A throat /A inlet > 1.8 would achieve the under-expanded flow in the divergent section of the nozzle. Next, the throat area was fixed at A throat /A inlet = 1.7, and the exit area was varied. The results are shown in Figure 5. The under-expansion condition can be achieved for the exit area ratio A exit /A inlet <.7. It shows that the exit area ust be saller than 150% of the throat area for the current nozzle design in order to achieve the under-expanded flow in the divergent section. The area ratios of the nozzle were deterined to be A throat /A inlet = 1.3 and A exit /A inlet =1.6. The throat area ratio was slightly saller than the above optiu in order to be on the safer side of achieving the choked condition. The exit area ratio was only 3% larger than the throat area to 4

5 guarantee the under-expansion condition and to avoid the risk of flow separation in the divergent section. The final design of the choked flow nozzle was selected as shown in Table. Based on the already deterined area ratios, the inlet radius is deterined to be as large as possible for better visualization and easureents within the liitations of the available high flow rate pup such that it can still supply enough inlet velocity and inlet pressure needed for the ixture flow at the throat to reach the choked condition. Figure 6 shows the final geoetry of the bubble augented propulsion nozzle. thrust gain. For the relatively high inlet velocity of 17.4 /s, this transition fro subsonic to supersonic flow occurs earlier at an injection void fraction of 40%. As expected, to achieve a choked flow, one needs a high inlet velocity or a high injection void fraction p inlet 350 kpa (3.5 at) u inlet 14.3 /s A throat /A inlet 1.3 A exit /A inlet 1.6 R inlet for choked flow for subsonic Table : Selected geoetry of the convergent-divergent nozzles for choked flow, operating conditions, and the corresponding predicted thrust gain indices. Figure 7: Predicted axial velocity along the length of the nozzle for the bubble augented propulsor sketched in Figure 6. The odel indicates that injection void fractions of 0.4 and larger achieve supersonic flow downstrea of the throat, while the flow reains subsonic for = 0. and 0.3. Figure 6: Final design of the bubble augented propulsor nozzle with a throat, which was built and tested. The predicted flow velocities in the nozzle at different injection void fractions are shown in Figure 7. In the siulations, the injection void fractions of 0.4, 0.5, and 0.6 achieved the supersonic flow downstrea of the throat, while the injection void fractions of 0. and 0.3 reained in the subsonic regie. The velocity decreases in the final divergent section downstrea of the throat for the subsonic flows, but it continues to accelerate for the supersonic flows. The predicted pressures along the nozzle are shown in Figure 8. Downstrea of the throat, the pressure increases for the subsonic flows, while it decreases for the supersonic flows. Figure 9 shows the oentu thrust gain index,, as a function of the injection void fraction,, for three selected inlet velocities. For the relatively low inlet velocity of 11.8 /s, the flow in the nozzle reains subsonic until the void fraction exceeds 50%. Above 50% the nozzle choked and resulted in a uch higher Figure 8: Predicted pressure along the length of the nozzle for the bubble augented propulsor sketched in Figure 6. Injection void fractions of 0.4 and larger achieve supersonic flow downstrea of the throat, while the inlet void fractions of 0. and 0.3 reained in subsonic flow. 5

6 Figure 11: Picture of the nozzle with pressure easureent ports. Flow direction is fro left to right. BUILT NOZZLE Figure 9: Predicted oentu thrust gain index,, vs. injection void fraction, for three different inlet velocities for the bubble augented propulsor sketched in Figure 6. Based on the nozzle design study described in the above section, the convergent-divergent section of the designed nozzle was fabricated fro clear Plexiglas to enable good visualization and was equipped with pressure ports. To enable high volue rates of air injection, a long air injection sections with central porous tubes was added upstrea of the nozzle. Figure 10 shows the diensions of the nozzle and the pressure ports arranged along the nozzle to easure the pressure profile during the tests. Figure 11 shows a picture of the finished nozzle test section. The pressure ports are connected to pressure sensor arrays. EXPERIMENTAL SETUP The test setup used in this study is shown in Figure 1. The liquid flow was driven by either one or two 15 HP pups (Goulds Model 3656) depending on flow conditions. Each pup is capable of a flow rate of.16 3 /in (570 gp) at 180 kpa (6 psi) or /in (30 gp) at 410 kpa (60 psi). When two pups were used, they could be configured to operate either in parallel to boost the flow rate or in series to boost the pressure. (a) (b) Figure 10: Drawing of the convergent-divergent nozzle: (a) a longitudinal cut with the flow direction fro right to left, (b) cross section at the throat section A-A. Figure 1: Sketch of the test setup for the Bubble Augented Propulsion experient. Figure 13 shows a flow diagra of the pup configuration that allows the two pups to work in parallel or in series, and Figure 14 shows a picture of the pup arrangeent. In this study, the two pups were configured in series to increase the upstrea pressure 6

7 because achieving high void fraction flows in the experiental setup was liited by the pup pressure and not by the pup flow rate. schee was used with a subersible load cell (PCB Load & Torque Model A, up to 00 lbf). Figure 15 shows a sketch of the force easureent setup, in which a 0. (8 inch) diaeter disk was used as force plate to capture the oentu force of the jet. The force applied to the disk is transferred to the load cell through a Teflon slide bearing ounted sooth stainless steel pipe. Figure 13: Flow diagra of the pup configuration with ultiple valves enabling serial (high pressure) or parallel (high flow) operation. Figure 15: A sketch of the setup for jet oentu force easureent. (a) Figure 14: Picture of the two pups for liquid flow with valves to operate in parallel or in series. Air injection was achieved by pushing air through a bundle of four 4-inch air injectors ade of DYNAPERM porous tubes placed along the axis of the injection section upstrea of the nozzle. Two high capacity air copressors were used in parallel to achieve the required high void fractions. Each air copressor was driven by a 5 HP otor and is rated for /in (5.4 CFM) at 60 kpa (90 psi). The nozzle test section was placed 30 c below the free surface in DYNAFLOW s wind wave tank, which was used here as a very large water reservoir, so that accuulation of air bubbles generated fro the testing is iniized. A flow straightening section was used between the air injection section and the nozzle inlet. Instruentation was provided for flow rates, pressures, and void fractions easureents as described in Chahine et al. (008) and Wu et al. (010). Additionally, a direct oentu force easureent Figure 16: Visualization of the flow inside the nozzle. Injection void fraction: (a) α = 0.%, (b) α = 1.7%, (c) α = 10%. Liquid flow rate is /in (100 gp) for all cases. FLOW VISUALIZATION High speed photography was used to visualize the flow through the nozzle. Figure 16 shows three pictures of the divergent exit section of the nozzle at different void 7

8 fractions. The liquid flow rare was /in (100 gp) for all three cases. As shown in the pictures, bubbles are a little ore concentrated at the top of the nozzle due to gravity effects. As the void fraction becoes higher, the bubbly ixture fills the nozzle section copletely as in the case of picture (c). Interestingly, for the higher void fractions case as in (b) and (c), clustering of the bubbles into organized separated bubble clouds inside the nozzle was observed. PRESSURE PROFILE Pressure profiles along the nozzle were obtained fro the pressure easureents at the port locations indicated in Figure 17. The port identification nubers are also shown in the figure. The port nuber is at the beginning of the convergent section, and port nuber 14 is at the throat. The easured pressure profiles at /in (100 gp) liquid flow rate for different void fractions up to α = 0. is shown in Figure 18. With the increase of the aount of air injection, upstrea pressure keeps increasing while the pressure decreases in the convergent section toward the throat. Downstrea of the throat, the pressure increases and recovers to the abient pressure at the exit. However, this recovery of the pressure in the diverging section gradually disappears as the void fraction increases. The trend even reversed above α = 0.16 and this corresponds to the expected behavior in a choked flow. In order to show the trend better, the pressures of Figure 18 are noralized by the pressure difference between the inlet (port No. ) and the throat (port No. 14), i.e. PP14 / P P14 as shown in Figure 19. As expected, the noralized pressure profile in the convergent section collapse together quite well. However, in the divergent section, the slopes of the noralized pressure profile change significantly as the void fraction increases fro positive to negative between = 0 to = 0.. Figure 17: Sketch of the location of the pressure ports with reference to the nozzle exit location and the beginning of the convergent section. Figure 18: Pressure profile along the length of the nozzle for different void fractions at injection between 0 and %. The liquid flow rate is /in (100 gp). Figure 19: Pressure profiles shown in Figure 18 after noralizing with the pressure difference between the inlet and the throat, PP14 / P P 14. The liquid flow rate is /in (100 gp). Figure 0 shows the pressure profile along the length of the nozzle for void fractions up to 3%. The liquid flow rate was the sae /in (100 gp). Corresponding noralized pressure profiles are shown in Figure 1. In these plots, the trend of pressures decreasing toward the exit is obvious. Experients were conducted also at a higher liquid flow rate of /in (00 gp). Figure shows the diensional pressure profiles, and Figure 3 shows the corresponding noralized pressure profiles at a /in (00 gp) liquid flow rate. The diensional pressures at the exit (actually the last port 13 before the exit), as shown in Figure, sees to increase above the abient pressure with the increase in. The exit pressure tends to be higher as the void fraction increases. This is a trait of supersonic flows where α = would be an over-expansion state (p exit lower than the abient pressure) and 8

9 α = and would be an under-expansion state (p exit higher than the abient pressure). When there is no air injection (α = 0), the pressure profile is sooth and follows the subsonic trend. However, for cases with high air injection (α > 0.065), a sudden pressure rise sees to occur where the nozzle geoetric slope changed (i.e. at the beginning of the convergent section and at the throat). The noralized pressure profiles with air injection fall on top of each other including for the local pressure rise after the throat as shown in Figure 3. The collapsed coon profile is quite different fro the noralized pressure profile without air injection. The sudden pressure rise is suspected to be as a result of bubble response to a sudden change in the flow field, and ay be related to the bubble clustering shown in Figure 16. Further investigations are required to understand this behavior better. Figure : Pressure profiles along the length of the nozzle for different injection void fractions in the range of 0 to 17%. The liquid flow rate is /in (00 gp). Abient pressure was 101 kpa (1 at). Figure 0: Pressure profile along the length of the nozzle for different injection void fractions in the range of 4% to 3%. The liquid flow rate is /in (100 gp). Figure 3: Pressure profile shown in Figure after noralizing the pressures by the pressure difference between PP / P P. the inlet and the throat, MIXTURE VELOCITY VS. SOUND SPEED Fro the pressure easureent and flow visualizations, we could not observe any obvious change in pressure or flow structure that would directly indicate a choked flow. Therefore an indirect evaluation of the ixture sound speed was sought. With the aount of air injection and pressure profile available, the air flow rate at any location, x, of the nozzle can be derived fro Figure 1: Pressure profiles of Figure 0 noralized by the pressure difference between the inlet and the throat, PP14 / P P 14. The liquid flow rate is /in (100 gp). P Q Qa ( x) Px ( ) inj a _ inj, (10) assuing isotheral expansion of the air. Here, P is inj the pressure of the ixture at the injection location and Q is the corresponding air flow rate at injection. a_ inj 9

10 Px ( ) and Qa ( x) are the pressure and air flow rate at the location, x, along the nozzle. With Qa available, the void fraction at the location of interest can be deterined by where Qa Q Q, (11) Ql is the liquid flow rate. a Figure 4: Void fractions along the nozzle length estiated fro the pressures in Figure 0 for different injection void fractions and for a liquid flow rate of /in (100 gp). l copared to those for /in (00 gp) condition. It appears that there are uch stronger bubble volue fluctuations right after the throat for the higher flow. With the void fraction available, the sound speed can be estiated fro the following equation: 1 1 L(1 ) G, c kp LcL (1) With the following values of the constants: specific heat ratio k = 1.0, liquid density =1000 kg/ 3, gas density = 1. kg/ 3, and sound speed in water =1485 /s. The ixture velocity, V, at any location, x, in the nozzle is estiated fro the easured water flow rate, the injected air flow rate, and the cross-sectional area, A, as follows: Q Q x V l a x, (13) A x where Qa is obtained by the isotheral relation (10) while the liquid is assued to be incopressible.. Figure 6 and Figure 7 show coparisons of the deduced sound speeds and ixture velocities along the nozzle at different injection void fractions. As seen in Figure 6, at a liquid flow rate of /in (100 gp), the sound speed in the ixture and the ixture velocity cross each other at a void fraction above about 0% downstrea of the throat section. However, at the higher liquid flow rate, /in (00 gp), as seen in Figure 7, the ixture speed exceeds the sound speed at relatively low injection void fractions, > 6%, and this occurs at the throat at the entrance to the divergent section. Figure 5: Void fractions along the nozzle length estiated fro the pressures in Figure for different injection void fractions and for a liquid flow rate of /in (00 gp). Figure 4 and Figure 5 show the void fraction variations along the nozzle at different air injection conditions estiated fro the easured pressures using (10) and (11) for a flow rate of respectively /in (100 gp) and /in (00 gp). Overall for these high void fraction conditions, as in a choked flow, the void fraction increases along the nozzle axis as we ove towards the nozzle exit. However, the variations are soother for the /in (100 gp) conditions as Figure 6: Variations of the sound speed and average ixture velocities deduced fro the pressure easureents along the nozzle at different injection void fractions. Liquid flow rate = /in (100 gp). 10

11 Figure 7: Variations of the sound speed and average ixture velocities deduced fro the pressure easureents along the nozzle at different injection void fractions. Liquid flow rate = /in (00 gp). FORCE MEASUREMENTS A potential advantage of achieving choked flow regie is iproved thrust augentation. Systeatic thrust easureents were conducted at the above two liquid flow rates and various void fractions to study thrust variation with increasing void fraction. An ipact plate approach, as we used in our previous work (Wu et al., 01b) was adopted. Figure 8 shows the variations of the force with the flow rate. The forces easured by the load cell at different values of the standoff distance between the nozzle exit and the easureents plate are copared with the calculated oentu of the jet. As shown in the figure, less force was easured as the standoff distance decreases fro 0.15 (6 inches) to 0.05 ( inches). However, in all cases the force easureent is well correlated with the nozzle thrust. The efficiency of the force easureent technique in capturing the jet exit oentu force is also exained. Figure 9 shows the variations of the noralized force captured by the plate, F / l QV l, versus the flow rate. The fraction of the captured exit oentu force decreases with increased exit ixture flow rate and reaches a plateau as observed in our previous study (Wu et al., 01b). This ay be attributed to the flow interaction between the nozzle flow and the flow deflected by the plate, which increases with the nozzle flow rate. In order to obtain the oentu thrust of the nozzle, T, the force F, directly easured by the load cell is corrected by the above easured capture efficiency, e, using: T F e. (14) Figure 30 shows the oentu waterjet thrust augentation index, ξ W, defined in (8) versus the void fraction. The figure also shows previously easured data with the ½ 3D divergent-convergent nozzle in (Wu et al., 01b). The thrust easureents indicate that the overall dependency of ξ W on is not too different between the previous nozzle and the convergent divergent nozzle, even though supersonic regie ay have been reached. These easured thrust agree with the 1D-BAP coputed thrust augentation. Overall, however, the thrust easureents of the current nozzle appear to result in a ξ W about 0% higher than what was achieved with the ½ 3D nozzle (Wu et al., 01b), but it is not clear if this is due to occurrence of a potential flow choking condition or to other easureents differences between the two syste. Reexaination of the two configurations under the sae setup would be useful to elucidate this point. Figure 8: Variations with the liquid flow rates of the force easured by a load cell on an ipact plate in front of the nozzle. Measureents are copared with the theoretical jet oentu thrust. Figure 9: Fraction of the total exit oentu force captured by the force easureent plate at different liquid flow rates. 11

12 Figure 3: Liquid only solution in the convergent-divergent flow nozzle predicted by 3DYNAFS-VIS. Liquid flow rate is /in (100 gp). Arrows represent velocity vectors, and color is the non-diensional pressure, p p u. / in Figure 30: Noralized waterjet thrust augentation, ξw, vs. exit void fraction. NUMERICAL STUDY The advanced nuerical odel based on a twoway coupling between the Eulerian description of the equivalent continuu flow field with 3DYNAFS-VIS and the Lagrangian tracking of the bubbles using 3DYNAFS-DSM was applied next. Figure 31 shows the coputational doain and the esh used in the nuerical siulations. Only a 90 quadrant of the nozzle was odeled, and a large volue downstrea of the nozzle exit was odeled to properly satisfy the exiting jet boundary conditions. This flow doain was represented by 60,000 cells. At the inlet, velocity was specified, and at the far downstrea, pressure was specified. At the nozzle walls no-slip boundary conditions were used. Figure 31: Coputational doain used in the 3DYNAFS nuerical odeling. A quadrant sector of the convergentdivergent nozzle was odeled with a large downstrea doain. Figure 33: Pressure distribution along the nozzle centerline and along the nozzle wall for liquid only flow of /in (100 gp). Predictions by 3DYNAFS-VIS are shown as well as experiental easureents. The liquid only solution was obtained first as illustrated in Figure 3 with the velocity vectors and the pressure contours. The boundary layer at the wall was well captured, and the iniu pressure occurred in the throat section as expected. Two pressure profiles along the nozzle are show in Figure 33, one along the centerline and the other close to the wall. The pressure along the centerline of the nozzle is slightly different fro the pressure along the wall of the nozzle. Since the pressure fro the experient was easured fro the wall, we can understand the kink in the easured profile is due to the local sudden change of slope of the nozzle wall. The easureents and the predictions agreed well in general. Figure 34 shows a siulated ixture flow in the nozzle for the injection void fraction of 10%. This siulation was conducted with the fully coupled twoway interaction odel, and the effects of the bubble dynaics on the ixture flow is taken in to account. Bubbly flow structuring into clusters is observed in the divergent section between the throat and the exit. Bubbles collect to low pressure regions that were convected downstrea. The distance between these 1

13 bubble clusters is about 14 in this case. Since the average ixture flow velocity is 4.5 /s in the divergent section, this leads to a tie period of 3 s, or a frequency of 30 Hz. This is far fro the natural frequency 7 khz of the 400 µ radius bubbles used in this siulation. In ters of nozzle diaeter based Strouhal nuber, it corresponds to Sd fd / u =1.8, which is not a particularly known value for nozzle exit flow. The length between the throat and the exit is Since the speed of sound in this ixture of about 0% void fraction is 30 /s, the acoustic resonance of the divergent section would be about 360 Hz. This suggests that the structuring would be related to the standing wave fored in the nozzle. The bubble clustering sees to be a real phenoenon as it is siilar to what was observed experientally in Figure 16. This structuring will be studied further. The exit oentu was easured using an ipact plate based thrust easureent schee. The experients showed good nozzle perforance with significant increase of the thrust augentation. However, the jet thrust augentation index was siilar to that of the subsonic nozzle, with a oentu thrust increase index about 0% higher than the subsonic regie nozzle. This study indicated that a well-designed flow nozzle can provide significant perforance iproveent since a W of 160% was easured for an exit void fraction of 60%. Coparing the analytical odel prediction and the experiental results indicated that the trend of the pressure variation in the nozzle was well predicted by the odel. The two-way coupled approach to the ixture flow in the nozzle was able to resolve the unsteady behavior of the bubbly flow and soe structuring of the void fraction in the nozzle with clustering of the bubbles at periodic intervals. Further studies are underway to understand the bubble clustering. ACKNOWLEDGEMENTS Figure 34: Siulation of the bubbly ixture flow in the convergent-divergent axisyetric nozzle using 3DYNAFS. Water flow rate is /in (100 gp), initial bubble radius 400 µ, void fraction 10%. CONCLUSIONS We have developed a convergent-divergent nozzle to study experientally the potential for choked flow in the nozzle and to investigate thrust gain under subsonic and choked flow conditions. An analytical odel for the choked flow was used to optiize the design of the nozzle, and a geoetry that theoretically could achieve choked conditions was built and tested. Experiental results at relatively high liquid speeds and high void fractions showed substantial departure fro the subsonic behavior in the divergent section of the nozzle. The pressure along the nozzle decreased (instead of classical subsonic increase) downstrea of the throat, while the velocity increased. Assuing conservation of volue of water and conservation of ass of the isotherally copressible air, the ixture flow velocity and the local void fraction along the nozzle were estiated fro the easured pressure distributions. The local variation along the nozzle of the speed of sound and the ixture flow speed were calculated based on the derived void fraction. This clearly indicated that supersonic flow was reached, i.e. that the local liquid speeds exceeded the local sound speed in the divergent section of the nozzle where the void fraction was high. This work was supported by the Office of Naval Research under contract N C-048 onitored by Dr. Ki-Han Ki. We gratefully acknowledge this support. REFERENCES Albagli, D. and Gany, A., High Speed Bubbly Nozzle Flow with Heat, Mass, and Moentu Interactions, International Journal of Heat and Mass Transfer, Vol. 46, pp , 003. Brennen, C. E., Cavitation and Bubble Dynaics, Oxford University Press, Chahine, G.L., Hsiao, C.-T., Choi, J.-K., Wu, X., Bubble Augented Waterjet Propulsion: Two-Phase Model Developent and Experiental Validation, Proc. 7th Syposiu on Naval Hydrodynaics, Seoul, Korea, October, 008. Chahine, G.L., Nuerical Siulation of Bubble Flow Interactions, Journal of Hydrodynaics, Ser. B, 1(3): p , 009. Gany, A., Gofer, A., Study of a Novel Air Augented Waterjet Boost Concept, Proc. 11th International Conference on Fast Sea Transportation FAST 011, Honolulu, Hawaii, USA, Septeber 011. Haberan, W.L. and Morton, R.K., An Experiental Investigation of the Drag and Shape of Air Bubbles Rising in Various Liquids, Report 80, DTMB,

14 Hsiao, C.-T. and Chahine, G.L., Nuerical Siulation of Bubble Dynaics in a Vortex Flow Using Navier- Strokes Coputation, Proc. Fourth International Syposiu on Cavitation CAV001, Pasadena, CA, 001. Hsiao, C.-T. and Chahine, G.L., Prediction of Vortex Cavitation Inception Using Coupled Spherical and Non- Spherical Models and Navier-Stokes Coputations, Proc. 4th Syposiu on Naval Hydrodynaics, Fukuoka, Japan, 00. Hsiao, C.-T. and Chahine, G.L., Prediction of Vortex Cavitation Inception Using Coupled Spherical and Non- Spherical Models and UnRANS Coputations, Journal of Marine Science and Technology, Vol. 8, No. 3, pp , 004a. Hsiao, C.-T. and Chahine, G.L., Nuerical Study of Cavitation Inception due to Vortex/Vortex Interaction in a Ducted Propulsor, Proc. 5th Syposiu on Naval Hydrodynaics, St. John s, Canada, Aug., 004b. Hsiao, C.-T. and Chahine, G.L., Scaling of Tip Vortex Cavitation Inception Noise with a Bubble Dynaics Model Accounting for Nuclei Size Distribution, Journal of Fluid Engineering, Vol. 17, pp , 005. Hsiao, C.-T., Ma, J., Chahine, G.L., Multi-Scale Two- Phase Flow Modeling of Sheet and Cloud Cavitation, Proc. 30 th Syposiu on Naval Hydrodynaics, Hobart, Tasania, Australia, -7 Noveber 014. Ishii, R., Ueda, Y., Murata, S., and Shishido, N., Bubbly Flows through a Converging-Diverging Nozzle, Physics of Fluids, Vol. 5, pp , Johnson, V.E. and Hsieh, T., The Influence of the Trajectories of Gas Nuclei on Cavitation Inception, Proc. Sixth Syposiu on Naval Hydrodynaics, pp , Kaeda, M. and Matsuoto, Y., Structure of Shock Waves in a Liquid Containing Gas Bubbles, Proc. IUTAM Syposiu on Waves in Liquid/Gas and Liquid/Vapor Two Phase Systes, pp , Li, A. and Ahadi, G., Dispersion and Deposition of Spherical Particles fro Point Sources in a Turbulent Channel Flow, Aerosol Science and Technology, Vol. 16, pp. 09-6, 199. Ma, J., Hsiao, C.-T. and Chahine, G.L., Euler-Lagrange Siulations of Bubble Cloud Dynaics near a Wall, to appear in ASME J. Fluids Eng., 014. Mor, M. and Gany, A. Analysis of Two-Phase Hoogeneous Bubbly Flows Including Friction and Mass Addition, J. of Fluids Engineering, Vol. 16, pp , 004. Muir, T.F. and Eichhorn, R., Copressible Flow of an Air-Water Mixture through a Vertical Two-Diensional Converging-Diverging Nozzle, Proc. Heat Transfer and Fluid Mechanics Institute, Stanford Univ. Press, pp , Preston, A., Colonius, T., and Brennen, C.E., A Nuerical Investigation of Unsteady Bubbly Cavitating Nozzle Flows, Proc. of the ASME Fluid Engineering Division Suer Meeting, Boston, 000. Saffan, P. G., The Lift on a Sall Sphere in a Slow Shear Flow, Journal of Fluid Mechanics, Vol., pp , Singh, S., Choi, J.-K., Chahine, G.L., Optiu Configuration of an Expanding-Contracting-Nozzle for Thrust Enhanceent by Bubble Injection, J. of Fluids Engineering, Trans. Of the ASME, Vol. 134, pp to , January 01. Singh, S., Foureau, T., Choi, J.-K., Chahine, G.L., Thrust Enhanceent through Bubble Injection into an Expanding-Contracting Nozzle with a Throat, Journal of Fluids Engineering, Vol.136, No.7, 014. Tangren, R.F., Dodge, C.H., and Seifert, H.S., Copressibility Effects in Two-Phase Flow, Journal of Applied Physics, Vol. 0 No. 7, pp , Wang, Y.-C. and Brennen, C.E., One-Diensional Bubbly Cavitating Flows through a Converging- Diverging Nozzle, Journal of Fluids Engineering, Vol. 10, pp , Wu, X., Choi, J.-K., Hsiao, C.-T., Chahine, G.L., Bubble Augented Waterjet Propulsion: Nuerical and Experiental Studies, Proc. 8th Syposiu on Naval Hydrodynaics, Pasadena, California, Septeber, 010. Wu, X., Choi, J.-K., Singh, S., Hsiao, C-T, and Chahine, G. L., Experiental and Nuerical Investigation of Bubble Augented Waterjet Propulsion, Journal of Hydrodynaics, Vol. 4, No. 5, pp , 01a. Wu, X., Singh, S., Choi, J.-K., Chahine, G.L., Waterjet Thrust Augentation using High Void Fraction Air Injection, Proc. 9th Syposiu on Naval Hydrodynaics, Gothenburg, Sweden, August 01b. 14

Effect of Nozzle Type on the Performance of Bubble Augmented Waterjet Propulsion

Effect of Nozzle Type on the Performance of Bubble Augmented Waterjet Propulsion Fourth International Syposiu on Marine Propulsors Effect of Nozzle Type on the Perforance of Bubble Augented Waterjet Propulsion SMP 15, Austin, Texas, USA, June 015 Xiongjun Wu 1, Jin-Keun Choi, Abigail

More information

Wave Force on Coastal Dike due to Tsunami

Wave Force on Coastal Dike due to Tsunami Wave Force on Coastal Dike due to Tsunai by Fuinori Kato 1, Shigeki Inagaki 2 and Masaya Fukuhaa 3 ABSTRACT This paper presents results of large-scale experients on wave force due to tsunai. A odel of

More information

Bubble Augmented Waterjet Propulsion: Two-Phase Model Development and Experimental Validation

Bubble Augmented Waterjet Propulsion: Two-Phase Model Development and Experimental Validation 27 th Symposium on Naval Hydrodynamics Seoul, Korea, 5-10 October 2008 Bubble Augmented Waterjet Propulsion: Two-Phase Model Development and Experimental Validation Georges L. Chahine, Chao-Tsung Hsiao,

More information

Numerical simulation on fluctuation in wellhead pressure of geothermal well

Numerical simulation on fluctuation in wellhead pressure of geothermal well Wellhead pressure (MPa) PROCEEDINGS, Thirty-Ninth Workshop on Geotheral Reservoir Engineering Stanford University, Stanford, California, February 4-6, 014 SGP-TR-0 Nuerical siulation on fluctuation in

More information

Integration of Lean Approaches to Manage a Manual Assembly System

Integration of Lean Approaches to Manage a Manual Assembly System Open Journal of Social Sciences, 204, 2, 226-23 Published Online Septeber 204 in SciRes. http://www.scirp.org/journal/jss http://dx.doi.org/0.4236/jss.204.29038 Integration of Lean Approaches to Manage

More information

Unit Activity Answer Sheet

Unit Activity Answer Sheet Geoetry Unit Activity Answer Sheet Unit: Extending to Three Diensions This Unit Activity will help you eet these educational goals: Matheatical Practices You will use atheatics to odel real-world situations.

More information

The Handtmann Armaturenfabrik. Safety without compromise. Safety valves for liquids, gases, and steam

The Handtmann Armaturenfabrik. Safety without compromise. Safety valves for liquids, gases, and steam The Handtann Araturenfabrik Safety without coproise for liquids, gases, and stea f Safety Valves FoodSafe Tradition Meets Innovation fro Handtann are first choice for hygienically sensitive product areas

More information

Application of Simulation Technology to Mitsubishi Air Lubrication System

Application of Simulation Technology to Mitsubishi Air Lubrication System 50 Application of Simulation Technology to Mitsubishi Air Lubrication System CHIHARU KAWAKITA *1 SHINSUKE SATO *2 TAKAHIRO OKIMOTO *2 For the development and design of the Mitsubishi Air Lubrication System

More information

MODELING AND SIMULATION OF VALVE COEFFICIENTS AND CAVITATION CHARACTERISTICS IN A BALL VALVE

MODELING AND SIMULATION OF VALVE COEFFICIENTS AND CAVITATION CHARACTERISTICS IN A BALL VALVE Proceedings of the 37 th International & 4 th National Conference on Fluid Mechanics and Fluid Power FMFP2010 December 16-18, 2010, IIT Madras, Chennai, India FMFP2010 341 MODELING AND SIMULATION OF VALVE

More information

Projectile Motion Lab (2019)

Projectile Motion Lab (2019) Nae: Date: Partner(s): Period: Projectile Motion Lab (2019) Object: Measure the velocity of a ball using two Photogates and coputer software for tiing. Apply concepts fro two-diensional kineatics to predict

More information

An improvement in calculation method for apparel assembly line balancing

An improvement in calculation method for apparel assembly line balancing Indian Journal of Fibre & Textile Research Vol.38, Septeber 2013, pp 259-264 An iproveent in calculation ethod for apparel assebly line balancing F Khosravi 1, a, A H Sadeghi 1 & F Jolai 2 1 Textile Departent,

More information

MODELLING THE EFFECTS OF PEDESTRIANS ON INTERSECTION CAPACITY AND DELAY WITH ACTUATED SIGNAL CONTROL

MODELLING THE EFFECTS OF PEDESTRIANS ON INTERSECTION CAPACITY AND DELAY WITH ACTUATED SIGNAL CONTROL MODELLING THE EFFECTS OF PEDESTRIANS ON INTERSECTION CAPACITY AND DELAY WITH ACTUATED SIGNAL CONTROL ABSTRACT Zong Tian, Ph.D., P.E. Feng Xu, Graduate Assistant Departent of Civil and Environental Engineering

More information

Effect of Surface Morphing on the Wake Structure and Performance of Pitching-rolling Plates

Effect of Surface Morphing on the Wake Structure and Performance of Pitching-rolling Plates Effect of Surface Morphing on the Wake Structure and Perforance of Pitching-rolling Plates Yan Ren 1, Geng Liu 2 and Haibo Dong 3 Departent of Mechanical & Aerospace Engineering University of Virginia,

More information

FEDSM DEVELOPMENT OF AN EFFICIENT PHASE SEPARATOR FOR SPACE AND GROUND APPLICATIONS

FEDSM DEVELOPMENT OF AN EFFICIENT PHASE SEPARATOR FOR SPACE AND GROUND APPLICATIONS Proceedings of the ASME 016 Fluids Engineering Division Summer Meeting FEDSM016 July 10-14, 016, Washington, DC, USA FEDSM016-7793 DEVELOPMENT OF AN EFFICIENT PHASE SEPARATOR FOR SPACE AND GROUND APPLICATIONS

More information

A parametric study of an offshore concrete pile under combined loading conditions using finite element method

A parametric study of an offshore concrete pile under combined loading conditions using finite element method 32 A paraetric stud of an offshore concrete pile under cobined loading conditions using finite eleent ethod J.A. Eicher, H. Guan 1 and D. S. Jeng School of Engineering, Griffith Universit Gold Coast Capus,

More information

URANS Simulations of Cavitation and Hull Pressure Fluctuation for Marine Propeller with Hull Interaction

URANS Simulations of Cavitation and Hull Pressure Fluctuation for Marine Propeller with Hull Interaction Third International Syposiu on Marine Propulsors sp 1, Launceston, Tasania, Australia, May 201 UANS Siulations of Caitation and Hull Pressure Fluctuation for Marine Propeller with Hull Interaction Kwang-Jun

More information

The water outgassing rate of internal surfaces of vacuum systems

The water outgassing rate of internal surfaces of vacuum systems Journal of Physics: Conference Series PAPER OPEN ACCESS The water outgassing rate of internal surfaces of vacuu systes Recent citations - Soe probles of the vacuu technique developent L N Rozanov and A

More information

CHARACTERISTICS OF BUBBLE SPLITTING IN A TIP VORTEX FLOW

CHARACTERISTICS OF BUBBLE SPLITTING IN A TIP VORTEX FLOW CAV3-GS-7- Fifth International Symposium on Cavitation (CAV3 Osaka, Japan, November -4, 3 CHARACTERISTICS OF BUBBLE SPLITTING IN A TIP VORTEX FLOW Jin-Keun Choi DYNAFLOW, INC. jkchoi@dynaflow-inc.com Georges

More information

Ripple Tank: Instruction Manual

Ripple Tank: Instruction Manual Ripple Tank: Instruction Manual The Ripple Tank coprises the following individual parts: Assebly of the ripple tank: Water Tank.......1pcs Detachable legs....3pcs Angular holders.......2pcs Plate fitting...1pcs

More information

EROSION AND ACCRETION ON CURVED BEACH

EROSION AND ACCRETION ON CURVED BEACH EROSION AND ACCRETION ON CURVED BEACH Kideok Do 1, Nobuhisa Kobayashi 2 and Kyung-Duck Suh 3 The perforance of a large nourishent project on Bethany Beach, Delaware is evaluated using available beach profile,

More information

Modeling of bubble generated noise in tip vortex cavitation inception

Modeling of bubble generated noise in tip vortex cavitation inception Modeling of bubble generated noise in tip vortex cavitation inception Jin-Keun Choi and Georges L. Chahine DYNAFLOW, INC. 10621-J Iron Bridge Road, Jessup, Maryland 20794-9381, U.S.A. jkchoi@dynaflow-inc.com,

More information

Applied Fluid Mechanics

Applied Fluid Mechanics Applied Fluid Mechanics 1. The Nature of Fluid and the Study of Fluid Mechanics 2. Viscosity of Fluid 3. Pressure Measurement 4. Forces Due to Static Fluid 5. Buoyancy and Stability 6. Flow of Fluid and

More information

Development of a DYNASWIRL Phase Separator for Space Applications

Development of a DYNASWIRL Phase Separator for Space Applications Appears in 50th AIAA Aerospace Sciences Meeting Online Proceedings including the New Horizons Forum and Aerospace Exposition (01) Development of a DYNASWIRL Phase Separator for Space Applications Xiongjun

More information

Buletinul Ştiinţific al Universităţii "POLITEHNICA" din Timişoara Seria HIDROTEHNICA TRANSACTIONS on HYDROTECHNICS

Buletinul Ştiinţific al Universităţii POLITEHNICA din Timişoara Seria HIDROTEHNICA TRANSACTIONS on HYDROTECHNICS Buletinul Ştiinţific al Universităţii "POLITEHNICA" din Tiişoara Seria HIDROTEHNICA TRANSACTIONS on HYDROTECHNICS To 55(69), Fascicola, 010 Experiental Stand for the Study of Unsteady Water Flow through

More information

IMPROVED SPECTRAL WAVE MODELLING OF WHITE-CAPPING DISSIPATION IN SWELL SEA SYSTEMS

IMPROVED SPECTRAL WAVE MODELLING OF WHITE-CAPPING DISSIPATION IN SWELL SEA SYSTEMS Proceedings of OMAE 2004: 23rd International Conference on Offshore Mechanics and Arctic Engineering 20-25 June 2004, Vancouver, Canada OMAE2004-51562 IMPROVED SPECTRAL WAVE MODELLING OF WHITE-CAPPING

More information

AIR EJECTOR WITH A DIFFUSER THAT INCLUDES BOUNDARY LAYER SUCTION

AIR EJECTOR WITH A DIFFUSER THAT INCLUDES BOUNDARY LAYER SUCTION Engineering MECHANICS, Vol. 20, 2013, No. 3/4, p. 213 220 213 AIR EJECTOR WITH A DIFFUSER THAT INCLUDES BOUNDARY LAYER SUCTION Václav Dvořák* The article deals with axial-symmetric subsonic air-to-air

More information

THEORETICAL EVALUATION OF FLOW THROUGH CENTRIFUGAL COMPRESSOR STAGE

THEORETICAL EVALUATION OF FLOW THROUGH CENTRIFUGAL COMPRESSOR STAGE THEORETICAL EVALUATION OF FLOW THROUGH CENTRIFUGAL COMPRESSOR STAGE S.Ramamurthy 1, R.Rajendran 1, R. S. Dileep Kumar 2 1 Scientist, Propulsion Division, National Aerospace Laboratories, Bangalore-560017,ramamurthy_srm@yahoo.com

More information

TUTORIAL. NPSHA for those who hate that stuffy word. by Jacques Chaurette p. eng. copyright 2006

TUTORIAL. NPSHA for those who hate that stuffy word. by Jacques Chaurette p. eng.  copyright 2006 TUTORIAL NPSHA for those who hate that stuffy word by Jacques Chaurette p. eng. www.lightmypump.com copyright 2006 page.2 NPSHA for those who hate that stuffy word This article follows the same approach

More information

Recommendations on Two Acceleration Measurements with Low Strain Integrity Test

Recommendations on Two Acceleration Measurements with Low Strain Integrity Test Recoendations on Two Acceleration Measureents with Low Strain Integrity Test Liqun Liang, PhD., P.E., 1 Scott Webster, P.E., 2 and Marty Bixler, P.E. 3 1 Pile Dynaics Inc., 3725 Aurora Rd, Cleveland, Ohio

More information

S.A. Klein and G.F. Nellis Cambridge University Press, 2011

S.A. Klein and G.F. Nellis Cambridge University Press, 2011 16-1 A flow nozzle is to be used to determine the mass flow rate of air through a 1.5 inch internal diameter pipe. The air in the line upstream of the meters is at 70 F and 95 psig. The barometric pressure

More information

DEVELOPMENT OF HIGH ALTITUDE TEST FACILITY FOR COLD JET SIMULATION

DEVELOPMENT OF HIGH ALTITUDE TEST FACILITY FOR COLD JET SIMULATION DEVELOPMENT OF HIGH ALTITUDE TEST FACILITY FOR COLD JET SIMULATION Aldin Justin 1, Robin James, Shruti Panicker 2,A.N.Subash,Saravana Kumar 1 Assistant Professor,Karunya University, aldinjustin@karunya.edu

More information

Estimation of the Effect of Cadence on Gait Stability in Young and Elderly People using Approximate Entropy Technique

Estimation of the Effect of Cadence on Gait Stability in Young and Elderly People using Approximate Entropy Technique MEASUREMENT SCIENCE REVIEW, Volue 4, Section 2, 4 Estiation of the Effect of Cadence on Gait Stability in Young and Elderly People using Approxiate Entropy Technique M. Arif *, Y. Ohtaki **, R. Nagatoi

More information

A Numerical Prediction of Wash Wave and Wave Resistance of High Speed Displacement Ships in Deep and Shallow Water

A Numerical Prediction of Wash Wave and Wave Resistance of High Speed Displacement Ships in Deep and Shallow Water การประช มว ชาการเคร อข ายว ศวกรรมเคร องกลแห งประเทศไทยคร งท 18 18- ต ลาคม 547 จ งหว ดขอนแก น A Nuerical Prediction of Wash Wave and Wave Resistance of High Speed Displaceent Ships in Deep and Shallow Water

More information

Study on Marine Propeller Running in Bubbly Flow

Study on Marine Propeller Running in Bubbly Flow Third International Symposium on Marine Propulsors smp 13, Launceston, Tasmania, Australia, May 2013 Study on Marine Propeller Running in Bubbly Flow Chiharu Kawakita Mitsubishi Heavy Industries, Ltd.,

More information

AppendkA. Prototype Labyrinth Spillways

AppendkA. Prototype Labyrinth Spillways AppendkA Prototype Labyrinth Spillways 131 This page intentionally left blank HYDRAULIC DESIGN OF LABYRINTH WEIRS 133 Labyrinth Spillway Installations noted in the Literature Nae Country Year Built Q 3/s

More information

PRESSURE WAVE PROPAGATION IN A BUBBLY MEDIUM: A MULTISCALE MODELLING APPROACH. Georges L. Chahine

PRESSURE WAVE PROPAGATION IN A BUBBLY MEDIUM: A MULTISCALE MODELLING APPROACH. Georges L. Chahine Proceedings of the ASME 2014 International Mechanical Engineering Congress and Exposition IMECE2014 November 14-20, 2014, Montreal, Quebec, Canada IMECE2014-36772 PRESSURE WAVE PROPAGATION IN A BUBBLY

More information

Race car damping 2. Fig-1 quarter car model.

Race car damping 2. Fig-1 quarter car model. Race car daping A nuber of issues ago I wrote an article on exploring approaches to specify a race car daper. This article is the second in that series and we shall be following on fro where we left off.

More information

Injector Dynamics Assumptions and their Impact on Predicting Cavitation and Performance

Injector Dynamics Assumptions and their Impact on Predicting Cavitation and Performance Injector Dynamics Assumptions and their Impact on Predicting Cavitation and Performance Frank Husmeier, Cummins Fuel Systems Presented by Laz Foley, ANSYS Outline Overview Computational Domain and Boundary

More information

Flow and Mixing in the Liquid between Bubbles

Flow and Mixing in the Liquid between Bubbles Excerpt from the Proceedings of the COMSOL Conference 2009 Boston Flow and Mixing in the Liquid between Bubbles Bruce A. Finlayson, Professor Emeritus of Chemical Engineering Department of Chemical Engineering,

More information

Brian P. Casaday and J. C. Vanderhoff Brigham Young University, Provo, Utah

Brian P. Casaday and J. C. Vanderhoff Brigham Young University, Provo, Utah P. SIMLATIOS OF ITERAL WAVES APPROACHIG A CRITICAL LEVEL Brian P. Casaday and J. C. Vanderhoff Brigha Young niversity, Provo, tah. BACKGROD Internal gravity waves exist abundantly in our world in stably-stratified

More information

Simulating the effects of fatigue and pathologies in gait

Simulating the effects of fatigue and pathologies in gait Siulating the effects of fatigue and pathologies in gait T Koura 1, A Nagano, H Leung 3 and Y Shinagawa 4 1,3 Departent of Coputer Engineering and Inforation Technology, City University of Hong Kong, 83

More information

Weight Optimization and Finite Element Analysis of Pressure Vessel Due to Thickness

Weight Optimization and Finite Element Analysis of Pressure Vessel Due to Thickness 2017 IJSRSET Volue 3 Issue 2 Print ISSN: 2395-1990 Online ISSN : 2394-4099 Theed Section: Engineering and Technology Weight Optiization and Finite Eleent Analysis of Pressure Vessel Due to Thickness Rashi

More information

Research and optimization of intake restrictor for Formula SAE car engine

Research and optimization of intake restrictor for Formula SAE car engine International Journal of Scientific and Research Publications, Volume 4, Issue 4, April 2014 1 Research and optimization of intake restrictor for Formula SAE car engine Pranav Anil Shinde Mechanical Engineering,

More information

Tutorial. BOSfluids. Relief valve

Tutorial. BOSfluids. Relief valve Tutorial Relief valve The Relief valve tutorial describes the theory and modeling process of a pressure relief valve or safety valve. It covers the algorithm BOSfluids uses to model the valve and a worked

More information

Invited Lecture Numerical Simulation of Bubble Flow Interactions Georges L. Chahine Dynaflow, Inc.

Invited Lecture Numerical Simulation of Bubble Flow Interactions Georges L. Chahine Dynaflow, Inc. Cavitation: Turbo-machinery & Medical Applications WIMRC FORUM 2008 Warwick University, UK, 7 th -9th July 2008 Invited Lecture Numerical Simulation of Bubble Flow Interactions Georges L. Chahine Dynaflow,

More information

EFFECT OF A PROPELLER AND GAS DIFFUSION ON BUBBLE NUCLEI DISTRIBUTION IN A LIQUID

EFFECT OF A PROPELLER AND GAS DIFFUSION ON BUBBLE NUCLEI DISTRIBUTION IN A LIQUID EFFECT OF A PROPELLER AND GAS DIFFUSION ON BUBBLE NUCLEI DISTRIBUTION IN A LIQUID HSIAO Chao-Tsung, CHAHINE Georges L., DYNAFLOW, INC., Jessup, Maryland 20794, USA, E-mail: ctsung@dynaflow-inc.com ABSTRACT

More information

Investigation on Divergent Exit Curvature Effect on Nozzle Pressure Ratio of Supersonic Convergent Divergent Nozzle

Investigation on Divergent Exit Curvature Effect on Nozzle Pressure Ratio of Supersonic Convergent Divergent Nozzle RESEARCH ARTICLE OPEN ACCESS Investigation on Divergent Exit Curvature Effect on Nozzle Pressure Ratio of Supersonic Convergent Divergent Nozzle Shyamshankar.M.B*, Sankar.V** *(Department of Aeronautical

More information

MXV. Vertical Multi-Stage In-Line Pumps. Construction. Applications

MXV. Vertical Multi-Stage In-Line Pumps. Construction. Applications MXV Construction Vertical ulti-stage pups with suction and delivery connections of the sae diaeter and arranged along the sae axis (in-line). Corrosion-resistant bearing sleeves lubricated by the puped

More information

AIRFLOW GENERATION IN A TUNNEL USING A SACCARDO VENTILATION SYSTEM AGAINST THE BUOYANCY EFFECT PRODUCED BY A FIRE

AIRFLOW GENERATION IN A TUNNEL USING A SACCARDO VENTILATION SYSTEM AGAINST THE BUOYANCY EFFECT PRODUCED BY A FIRE - 247 - AIRFLOW GENERATION IN A TUNNEL USING A SACCARDO VENTILATION SYSTEM AGAINST THE BUOYANCY EFFECT PRODUCED BY A FIRE J D Castro a, C W Pope a and R D Matthews b a Mott MacDonald Ltd, St Anne House,

More information

ANALYSIS OF AERODYNAMIC CHARACTERISTICS OF A SUPERCRITICAL AIRFOIL FOR LOW SPEED AIRCRAFT

ANALYSIS OF AERODYNAMIC CHARACTERISTICS OF A SUPERCRITICAL AIRFOIL FOR LOW SPEED AIRCRAFT ANALYSIS OF AERODYNAMIC CHARACTERISTICS OF A SUPERCRITICAL AIRFOIL FOR LOW SPEED AIRCRAFT P.Sethunathan 1, M.Niventhran 2, V.Siva 2, R.Sadhan Kumar 2 1 Asst.Professor, Department of Aeronautical Engineering,

More information

An Indian Journal FULL PAPER ABSTRACT KEYWORDS. Trade Science Inc.

An Indian Journal FULL PAPER ABSTRACT KEYWORDS. Trade Science Inc. [Type text] [Type text] [Type text] ISSN : 0974-7435 Volue 10 Issue 24 BioTechnology 2014 An Indian Journal FULL PAPER BTAIJ, 10(24), 2014 [15430-15434] Mechanical analysis of tennis racket and ball during

More information

Micro Channel Recuperator for a Reverse Brayton Cycle Cryocooler

Micro Channel Recuperator for a Reverse Brayton Cycle Cryocooler Micro Channel Recuperator for a Reverse Brayton Cycle Cryocooler C. Becnel, J. Lagrone, and K. Kelly Mezzo Technologies Baton Rouge, LA USA 70806 ABSTRACT The Missile Defense Agency has supported a research

More information

Influence of rounding corners on unsteady flow and heat transfer around a square cylinder

Influence of rounding corners on unsteady flow and heat transfer around a square cylinder Influence of rounding corners on unsteady flow and heat transfer around a square cylinder S. K. Singh Deptt. of Mech. Engg., M. B. M. Engg. College / J. N. V. University, Jodhpur, Rajasthan, India Abstract

More information

Effects of non-condensable gas on cavitating flow over a cylinder

Effects of non-condensable gas on cavitating flow over a cylinder Effects of non-condensable gas on cavitating flow over a cylinder Abstract Filipe Brandao; Mrugank Bhatt; Krishnan Mahesh* University of Minnesota, Minneapolis, MN, USA The effect of non-condensable gas

More information

Study on Fire Plume in Large Spaces Using Ground Heating

Study on Fire Plume in Large Spaces Using Ground Heating Available online at www.sciencedirect.com Procedia Engineering 11 (2011) 226 232 The 5 th Conference on Performance-based Fire and Fire Protection Engineering Study on Fire Plume in Large Spaces Using

More information

The Mechanism Study of Vortex Tools Drainage Gas Recovery of Gas Well

The Mechanism Study of Vortex Tools Drainage Gas Recovery of Gas Well Advances in Petroleum Exploration and Development Vol. 7, No. 1, 214, pp. 62-66 DOI:1.3968/j.aped.1925543821471.1931 ISSN 1925-542X [Print] ISSN 1925-5438 [Online] www.cscanada.net www.cscanada.org The

More information

NUMERICAL AND EXPERIMENTAL INVESTIGATION OF THE FLOWFIELD IN A BLOWDOWN WIND TUNNEL

NUMERICAL AND EXPERIMENTAL INVESTIGATION OF THE FLOWFIELD IN A BLOWDOWN WIND TUNNEL ICAS 2002 CONGRESS NUERICAL AND EXPERIENTAL INVESTIGATION OF THE FLOWFIELD IN A BLOWDOWN WIND TUNNEL Ali Rebaine, ahmood Khalid, Cabot Broughton and Fred Ellis Institute for Aerospace Research, National

More information

NUMERICAL INVESTIGATION OF THE FLOW BEHAVIOUR IN A MODERN TRAFFIC TUNNEL IN CASE OF FIRE INCIDENT

NUMERICAL INVESTIGATION OF THE FLOW BEHAVIOUR IN A MODERN TRAFFIC TUNNEL IN CASE OF FIRE INCIDENT - 277 - NUMERICAL INVESTIGATION OF THE FLOW BEHAVIOUR IN A MODERN TRAFFIC TUNNEL IN CASE OF FIRE INCIDENT Iseler J., Heiser W. EAS GmbH, Karlsruhe, Germany ABSTRACT A numerical study of the flow behaviour

More information

A & AE 520 Background Information, Adapted from AAE334L, last revised 10-Feb-14 Page 1 1. SUPERSONIC WIND TUNNEL

A & AE 520 Background Information, Adapted from AAE334L, last revised 10-Feb-14 Page 1 1. SUPERSONIC WIND TUNNEL A & AE 50 Background Information, Adapted from AAE334L, last revised 10-Feb-14 Page 1 1.1 BACKGROUND 1. SUPERSONIC WIND TUNNEL 1.1.1 Objectives: This handout is adapted from the one once used in AAE334L

More information

A Computational Assessment of Gas Jets in a Bubbly Co-Flow 1

A Computational Assessment of Gas Jets in a Bubbly Co-Flow 1 A Computational Assessment of Gas Jets in a Bubbly Co-Flow 1 Melissa Fronzeo*, 1 Michael Kinzel 1 The Pennsylvania State University, University Park, PA, USA Abstract In this effort, Computational Fluid

More information

On Runway Capacity and Wake Vortex Safe Separation Distance (SSD)

On Runway Capacity and Wake Vortex Safe Separation Distance (SSD) On Runway Capacity and Wake Vortex Safe Separation Distance (SSD) L.M.B.C. Capos CCTAE (Center for Aeronautical and Space Science and Tecnology), Instituto Superior Tecnico, Lisbon Technnical University.

More information

ON THE EFFECT OF LIFT FORCES IN BUBBLE PLUMES

ON THE EFFECT OF LIFT FORCES IN BUBBLE PLUMES Ninth International Conference on CFD in the Minerals and Process Industries CSIRO, Melbourne, Australia 10-12 December 2012 ON THE EFFECT OF LIFT FORCES IN BUBBLE PLUMES Jan Erik OLSEN* and Mihaela POPESCU

More information

Workshop 1: Bubbly Flow in a Rectangular Bubble Column. Multiphase Flow Modeling In ANSYS CFX Release ANSYS, Inc. WS1-1 Release 14.

Workshop 1: Bubbly Flow in a Rectangular Bubble Column. Multiphase Flow Modeling In ANSYS CFX Release ANSYS, Inc. WS1-1 Release 14. Workshop 1: Bubbly Flow in a Rectangular Bubble Column 14. 5 Release Multiphase Flow Modeling In ANSYS CFX 2013 ANSYS, Inc. WS1-1 Release 14.5 Introduction This workshop models the dispersion of air bubbles

More information

Lab # 03: Visualization of Shock Waves by using Schlieren Technique

Lab # 03: Visualization of Shock Waves by using Schlieren Technique AerE545 Lab # 03: Visualization of Shock Waves by using Schlieren Technique Objectives: 1. To get hands-on experiences about Schlieren technique for flow visualization. 2. To learn how to do the optics

More information

OPTIMIZATION OF RECUPERATER FIN GEOMETRY FOR MICRO GAS TURBINE

OPTIMIZATION OF RECUPERATER FIN GEOMETRY FOR MICRO GAS TURBINE OPTIMIZATION OF RECUPERATER FIN GEOMETRY FOR MICRO GAS TURBINE S.Ramamurthy 1 and Bharat Makwana 2 1 Scientist,National Aerospace Laboratories, Bangalore, ramamurthy_srm@yahoo.com 2 Engineer,INOX Private

More information

Experimental Analysis on Vortex Tube Refrigerator Using Different Conical Valve Angles

Experimental Analysis on Vortex Tube Refrigerator Using Different Conical Valve Angles International Journal of Engineering Research and Development e-issn: 7-067X, p-issn: 7-00X, www.ijerd.com Volume 3, Issue 4 (August ), PP. 33-39 Experimental Analysis on Vortex Tube Refrigerator Using

More information

An Impeller Blade Analysis of Centrifugal Gas Compressor Using CFD

An Impeller Blade Analysis of Centrifugal Gas Compressor Using CFD An Impeller Blade Analysis of Centrifugal Gas Compressor Using CFD Vivek V. Kulkarni Department of Mechanical Engineering KLS Gogte Institute of Technology, Belagavi, Karnataka Dr. Anil T.R. Department

More information

501 Interchange Design Interchange Design Considerations... 10

501 Interchange Design Interchange Design Considerations... 10 5 Interchange Design Table of Contents 51 Interchange Design... 1 51.1 General...1 51.2 Interchange Type...1 51.2.1 Diaond Interchanges... 1 51.2.1.1 Tight Urban Diaond Interchange (TUDI)... 1 51.2.1.2

More information

Name: Answer Key Date: Regents Physics. Waves

Name: Answer Key Date: Regents Physics. Waves Nae: Answer Key Date: Regents Physics Test # 13 Review Waves 1. Use GUESS ethod and indicate all vector directions. 2. Ters to know: echanical wave, transverse wave, longitudinal wave, surace wave, electroagnetic

More information

AN OPTIMIZATION MODEL AND ALGORITHM OF STUDENTS' PHYSICAL FITNESS TEST SEQUENCE

AN OPTIMIZATION MODEL AND ALGORITHM OF STUDENTS' PHYSICAL FITNESS TEST SEQUENCE 28 th February 203. Vol. 48 3 2005-203 JATIT & LLS. All rights reserved. ISSN: 992-8645 www.jatit.org E-ISSN: 87-395 AN OPTIMIZATION MODEL AND ALGORITHM OF STUDENTS' PHYSICAL FITNESS TEST SEQUENCE JINSONG

More information

Linear Seakeeping High Sea State Applicability

Linear Seakeeping High Sea State Applicability Proceedings of the 16 th International Ship Stability Workshop, 5-7 June 2017, Belgrade, Serbia 1 Linear Seakeeping High Sea State Applicability Tiothy C. Sith, Naval Surface Warfare Center Carderock Division,

More information

SEMI-SUBMERSIBLE YACHT CONCEPT: RETHINKING BEHAVIOUR AT ANCHOR AND GENESIS OF THE COMFORT DRAFT

SEMI-SUBMERSIBLE YACHT CONCEPT: RETHINKING BEHAVIOUR AT ANCHOR AND GENESIS OF THE COMFORT DRAFT 24 th International HISWA Syposiu on Yacht Design and Yacht Construction 14 and 15 Noveber 2016, Asterda, The Netherlands, RAI Asterda SEMI-SUBMERSIBLE YACHT CONCEPT: RETHINKING BEHAVIOUR AT ANCHOR AND

More information

STUDY OF PRESSURE WAVE PROPAGATION IN A TWO-PHASE BUBBLY MIXTURE 1 DYNAFLOW, INC J Iron Bridge Road, Jessup, MD, USA

STUDY OF PRESSURE WAVE PROPAGATION IN A TWO-PHASE BUBBLY MIXTURE 1 DYNAFLOW, INC J Iron Bridge Road, Jessup, MD, USA STUDY OF PRESSURE WAVE PROPAGATION IN A TWO-PHASE BUBBLY MIXTURE 1 Reni Raju 2, Sowmitra Singh, Chao-Tsung Hsiao, and Georges Chahine DYNAFLOW, INC. www.dynaflow-inc.com 10621-J Iron Bridge Road, Jessup,

More information

Numerical Simulations of a Train of Air Bubbles Rising Through Stagnant Water

Numerical Simulations of a Train of Air Bubbles Rising Through Stagnant Water Numerical Simulations of a Train of Air Bubbles Rising Through Stagnant Water Hong Xu, Chokri Guetari ANSYS INC. Abstract Transient numerical simulations of the rise of a train of gas bubbles in a liquid

More information

Design of a Solid Wall Transonic Wind Tunnel

Design of a Solid Wall Transonic Wind Tunnel Design of a Solid Wall Transonic Wind Tunnel David Wall * Auburn University, Auburn, Alabama, 36849 A solid wall transonic wind tunnel was designed with optical access from three sides to allow for flow

More information

DISCHARGE OF NON-REACTIVE FLUIDS FROM VESSELS1

DISCHARGE OF NON-REACTIVE FLUIDS FROM VESSELS1 Brazilian Journal of Cheical Engineering ISSN 0104-6632 Printed in Brazil www.scielo.br/bjce Vol. 34, No. 04, pp. 1149 1159, October Deceber, 2017 dx.doi.org/10.1590/0104-6632.20170344s20160158 DISCHARGE

More information

A comparison of NACA 0012 and NACA 0021 self-noise at low Reynolds number

A comparison of NACA 0012 and NACA 0021 self-noise at low Reynolds number A comparison of NACA 12 and NACA 21 self-noise at low Reynolds number A. Laratro, M. Arjomandi, B. Cazzolato, R. Kelso Abstract The self-noise of NACA 12 and NACA 21 airfoils are recorded at a Reynolds

More information

Visual Observation of Nucleate Boiling and Sliding Phenomena of Boiling Bubbles on a Horizontal Tube Heater

Visual Observation of Nucleate Boiling and Sliding Phenomena of Boiling Bubbles on a Horizontal Tube Heater Proceedings of the 2 nd World Congress on Mechanical, Chemical, and Material Engineering (MCM'16) Budapest, Hungary August 22 23, 216 Paper No. HTFF 146 DOI:.11159/htff16.146 Visual Observation of Nucleate

More information

The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul

The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration M. Burak Şamşul ITU AYOC 2014 - Milper Pervane Teknolojileri Company Profile MILPER is established in 2011 as a Research and Development

More information

Analysis of pressure losses in the diffuser of a control valve

Analysis of pressure losses in the diffuser of a control valve Analysis of pressure losses in the diffuser of a control valve Petr Turecký 1, Lukáš Mrózek 2*, Ladislav Taj 2, and Michal Kolovratník 3 1 ENVIROS, s.r.o., Dykova 53/10, 101 00 Praha 10-Vinohrady, Czech

More information

COMPUTATIONAL FLOW MODEL OF WESTFALL'S LEADING TAB FLOW CONDITIONER AGM-09-R-08 Rev. B. By Kimbal A. Hall, PE

COMPUTATIONAL FLOW MODEL OF WESTFALL'S LEADING TAB FLOW CONDITIONER AGM-09-R-08 Rev. B. By Kimbal A. Hall, PE COMPUTATIONAL FLOW MODEL OF WESTFALL'S LEADING TAB FLOW CONDITIONER AGM-09-R-08 Rev. B By Kimbal A. Hall, PE Submitted to: WESTFALL MANUFACTURING COMPANY September 2009 ALDEN RESEARCH LABORATORY, INC.

More information

Improvement of the Volumetric and Isentropic Efficiency Due to Modifications of the Suction Chamber

Improvement of the Volumetric and Isentropic Efficiency Due to Modifications of the Suction Chamber Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2008 Improvement of the Volumetric and Isentropic Efficiency Due to Modifications of the

More information

International Journal of Technical Research and Applications e-issn: , Volume 4, Issue 3 (May-June, 2016), PP.

International Journal of Technical Research and Applications e-issn: ,  Volume 4, Issue 3 (May-June, 2016), PP. DESIGN AND ANALYSIS OF FEED CHECK VALVE AS CONTROL VALVE USING CFD SOFTWARE R.Nikhil M.Tech Student Industrial & Production Engineering National Institute of Engineering Mysuru, Karnataka, India -570008

More information

Bubble-bubble interactions and wall pressures/temperatures produced by the collapse of a bubble pair near a rigid surface

Bubble-bubble interactions and wall pressures/temperatures produced by the collapse of a bubble pair near a rigid surface Bubble-bubble interactions and wall pressures/temperatures produced by the collapse of a bubble pair near a rigid surface Abstract Shahaboddin A. Beig*; Eric Johnsen; Mechanical Engineering Department,

More information

Investigation of Suction Process of Scroll Compressors

Investigation of Suction Process of Scroll Compressors Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2006 Investigation of Suction Process of Scroll Compressors Michael M. Cui Trane Jack Sauls

More information

OPTIMIZING THE LENGTH OF AIR SUPPLY DUCT IN CROSS CONNECTIONS OF GOTTHARD BASE TUNNEL. Rehan Yousaf 1, Oliver Scherer 1

OPTIMIZING THE LENGTH OF AIR SUPPLY DUCT IN CROSS CONNECTIONS OF GOTTHARD BASE TUNNEL. Rehan Yousaf 1, Oliver Scherer 1 OPTIMIZING THE LENGTH OF AIR SUPPLY DUCT IN CROSS CONNECTIONS OF GOTTHARD BASE TUNNEL Rehan Yousaf 1, Oliver Scherer 1 1 Pöyry Infra Ltd, Zürich, Switzerland ABSTRACT Gotthard Base Tunnel with its 57 km

More information

Liquid Holdup in Geothermal Wells

Liquid Holdup in Geothermal Wells Proceedings World Geotheral Congress 005 Antalya, Turkey, 4-9 April 005 Liquid Holdup in Geotheral Wells Sabodh K. Garg, John W. Pritchett, and Jaes H. Alexander Science Applications International Corporation

More information

Design of Saddle Support for Horizontal Pressure Vessel Vinod Kumar, Navin Kumar, Surjit Angra, Prince Sharma

Design of Saddle Support for Horizontal Pressure Vessel Vinod Kumar, Navin Kumar, Surjit Angra, Prince Sharma World Acadey of Science, Engineering and Technology Vol:8, No:, 0 Design of Saddle Support for Horizontal Pressure Vessel Vinod Kuar, Navin Kuar, Surjit Angra, Prince Shara International Science Index,

More information

INTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK

INTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK INTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK ABSTRACT Ventilation stacks are becoming increasingly common in the design of naturally

More information

Sizing Pulsation Dampeners Is Critical to Effectiveness

Sizing Pulsation Dampeners Is Critical to Effectiveness Sizing Pulsation Dampeners Is Critical to Effectiveness Pressure variation is an important consideration when determining the appropriate size pulsation dampener needed for an application. by David McComb,

More information

TRAILED SPRAYERS RPS SERIES

TRAILED SPRAYERS RPS SERIES TRAILED SPRAYERS RPS SERIES The outstanding quality of the new series of trailed sprayers fro Lochann Plantatec is the result of over fifty years of practical experience, the application of state-of-the-art

More information

THE INNER WORKINGS OF A SIPHON Jacques Chaurette p. eng. January 2003

THE INNER WORKINGS OF A SIPHON Jacques Chaurette p. eng.  January 2003 THE INNER WORKINGS OF A SIPHON Jacques Chaurette p. eng. www.lightmypump.com January 2003 Synopsis The objective of this article is to explain how a siphon works. The difference between low pressure, atmospheric

More information

Development of High-speed Gas Dissolution Device

Development of High-speed Gas Dissolution Device Development of High-speed Gas Dissolution Device Yoichi Nakano*, Atsushi Suehiro**, Tetsuhiko Fujisato***, Jun Ma**** Kesayoshi Hadano****, Masayuki Fukagawa***** *Ube National College of Technology, Tokiwadai

More information

Paper 2.2. Operation of Ultrasonic Flow Meters at Conditions Different Than Their Calibration

Paper 2.2. Operation of Ultrasonic Flow Meters at Conditions Different Than Their Calibration Paper 2.2 Operation of Ultrasonic Flow Meters at Conditions Different Than Their Calibration Mr William Freund, Daniel Measurement and Control Mr Klaus Zanker, Daniel Measurement and Control Mr Dale Goodson,

More information

C6Hi (g) 6 H2O + 6 C02(g) + energy

C6Hi (g) 6 H2O + 6 C02(g) + energy Experient Cell Respiration 110 Cell respiration refers to the process of converting the cheical energy of organic olecules into a for iediately usable by organiss. Glucose ay be oxidized copletely if sufficient

More information

Figure 1 Schematic of opposing air bearing concept

Figure 1 Schematic of opposing air bearing concept Theoretical Analysis of Opposing Air Bearing Concept This concept utilizes air bearings to constrain five degrees of freedom of the optic as shown in the figure below. Three pairs of inherently compensated

More information

Experimental Investigation Of Flow Past A Rough Surfaced Cylinder

Experimental Investigation Of Flow Past A Rough Surfaced Cylinder (AET- 29th March 214) RESEARCH ARTICLE OPEN ACCESS Experimental Investigation Of Flow Past A Rough Surfaced Cylinder Monalisa Mallick 1, A. Kumar 2 1 (Department of Civil Engineering, National Institute

More information

HYDRAULICS. H89.8D - Hydraulic Bench

HYDRAULICS. H89.8D - Hydraulic Bench HYDRAULICS H89.8D - Hydraulic Bench 1. General The H89.8D and ancillary equipment have been developed to provide a comprehensive range of experiments in fluid mechanics. The bench is of robust construction

More information

Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers

Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers Purdue University Purdue e-pubs International Refrigeration and Air Conditioning Conference School of Mechanical Engineering 2016 Single Phase Pressure Drop and Flow Distribution in Brazed Plate Heat Exchangers

More information

RELATIONS BETWEEN CENTRIFUGAL BASKET DESIGNS AND MASSECUITE CHARACTERISTICS

RELATIONS BETWEEN CENTRIFUGAL BASKET DESIGNS AND MASSECUITE CHARACTERISTICS Proceedings of The South African Sugar Technologists' Association - April 1967 79 RELATIONS BETWEEN CENTRIFUGAL BASKET DESIGNS AND MASSECUITE CHARACTERISTICS by Dr. HELMUT EICHHORN Salzgitter Maschinen

More information