BAUSCH & LOMB ENGINEERING ROCHESTER. Title: Membrane Press Procedure Page 1 of 14
|
|
- Phebe Poole
- 5 years ago
- Views:
Transcription
1 Title: Membrane Press Procedure Page 1 of 14 Author: K. Schober Attachments: 3 Released by: Date: 5/5/06 Global Document Management DCO-SOPROC PURPOSE/SCOPE To provide instructions for how to conduct the test of the biological tissue (rhexis). RESPONSIBILITY It is the responsibility of all the operators to read through this procedure prior to beginning any testing, and to follow this procedure to correctly and safely perform the necessary testing. MATERIALS AND EQUIPMENT Equipment Linear Stage (S/N B ) Load Cell (94062) Forceps (Peer-Vigor ) Controller (ESP100) Saline Bath (11304) Sample Mount (11301/11302) Amplifier Materials Wipe (TechniCloth TX606) Isopropyl Alcohol 99% (IPA) RM 1290 O-ring (S70-M.38X3.37, S70-M1X2) MEMBRANE PRESS SETUP This procedure demonstrates how to setup the device prior to testing. Step Action 1 Plug in the Newport Controller and the USB connector or RS232 cable, whichever is compatible with the computer. Turn the power on.
2 Title: Membrane Press Procedure Page 2 of 14 2 Plug in the Amplifier. 3 Plug the USB from the Data Acquisition card into the computer.
3 Title: Membrane Press Procedure Page 3 of 14 4 Open the ESP-Util Program. A Select Communications Port pop-up should be up. Select the Serial (RS232) as the port type. Select preferred Com Port. Click Open Port. Click Yes to Reset Controller. After all this has been completed, you may close out of the ESP-Util Program (Either click the X in the top-right corner or File-Exit). 5 Open Labview Programs named, AlignmentVI_revised on and Complete Test Procedure. 6 Gently screw probe tip attachment into the load cell. NOTE: Load cell pins MUST be in the load cell to screw the probe tip in. Probe tip attachment Load Cell pins
4 Title: Membrane Press Procedure Page 4 of 14 SAMPLE PREPARATION This procedure demonstrates how to prepare the sample and load sample mount prior to testing. Step Action 1 Using forceps take an o-ring (red) and place in designated location on mount. Should be a snug fit. Bottommount piece. O-ring 2 Using the forceps take the material and carefully place it over the o-ring. Make sure that are no creases and that the material is resting flat over the opening with no sagging. NOTE: To make this step easier you could use a microscope while placing the material over the o-ring.
5 Title: Membrane Press Procedure Page 5 of 14 3 Place the top mount piece on the bottom mount. Use the three pins protruding from the bottom mount to guide the top. Bottom-side of top piece 3 pins on bottom piece NOTE: The top-side of the top piece looks like this: Notice that the hole looks larger.
6 Title: Membrane Press Procedure Page 6 of 14 4 Pull and stretch the 3 knobs up and over the top piece. Make sure that they rest in their notch. Before After 5 1. If testing material in saline solution, skip to step 7 2. If testing dry, proceed with step 6. 6 Place mount into saline bath. Saline bath 7 Off to the side fill a large container with saline solution. Skip to Membrane Press Alignment procedure. 8 Taking the saline bath piece and the sample mount piece slowly submerge both separately into the container. Angling the two pieces while inserting the sample mount into the saline bath piece. NOTE: The key to this is eliminating as many air bubbles as possible.
7 Title: Membrane Press Procedure Page 7 of 14 MEMBRANE PRESS ALIGNMENT This procedure demonstrates how to align the probe tip to the center of the micrometer stage. This procedure must be completed after each test. Step Action NOTE *The micrometer slides should have been in the locked position prior to alignment. If the knobs weren t locked BE CAUTIOUS when lowering the probe. 1 Carefully place sample mount (from Sample Mount Preparation) into its designated location watching out for the probe tip. Sample mount rests in here. 2 Carefully remove the two pins from the load cell.
8 Title: Membrane Press Procedure Page 8 of 14 3 Use the AlignmentVI_revised on LabVIEW program to lower stage. Click the white arrow in the top left corner, and then click the Reset Motor back ON button. White arrow Forc e dial This is where you type in desired position. 4 Lower the stage to position 19. Type, into the Target Position, then click Move. The probe tip will not hit the mount at this position. 5 Closely look at the probe tip and the hole to verify that the probe tip will not come in contact. 6 Lower the stage to position 20 (using the same method in Step 4), while checking the force dial on the computer screen. After the stage has stopped it should read noise from the load cell. Ranging from g to.00892g. NOTE: There is an overload built into this program, if the load cell reads a force of 5 grams or greater the stage will immediately stop. If this occurs raise stage to position 0 using step 4. 7 Repeat Step 4, lowering the stage to position 21. Looking at the hole and the tip. Use the micrometer stage if adjustments need to be taken. At this position the tip will be half way in the whole. 8 Repeat Step 4, lower stage to 22. This is the position you ll align the probe and stage following the next steps listed out. NOTE: At this position the range of force should be to.00892, which is noise.
9 Title: Membrane Press Procedure Page 9 of 14 9 Using the x-direction micrometer slide. Move the stage to the left until the force dial reads +/ g. Read and record the position on the slide on appropriate data sheet (See Attachment 1). Turn knob in this direction will move stage to the LEFT. LOCKS stage Turn knob in this direction will move stage to the RIGHT. 10 Repeat Step 10, moving stage to the right side. 11 Take the measurements from Step 10 and 11; take the average of the two. Move the x-direction slide to the average location. NOTE: The slide will need to be moved to the left. 12 Using the y-direction micrometer slide. Move the stage to the bottom until the force dial reads +/ g. Read and record the position on the slide on appropriate data sheet (See Attachment 1). LOCKS stage Turn knob in this direction will move stage to the LEFT. Turn knob in this direction will move stage to the LEFT. 13 Repeat Step 13, moving stage to the top. 14 Lock stage in y-direction. 15 Repeat Steps Lock stage in x-direction.
10 Title: Membrane Press Procedure Page 10 of 14 TEST EXECUTION AND DATA ANALYSIS This procedure demonstrates how to run a test and analyze the data. Step Action 1 The AlignmentVI_revised on LabVIEW program should still be up from the alignment procedure. Click the Red Stop Sign button in the top left corner. 2 Open the Complete Test Procedure LabVIEW program. Click the white arrow and then click the Move button. This button initiates the test. NOTE: If for any reason the test needs to be terminated, click the Emergency OFF! button. 3 The test will be completed if the overload is reached (5 grams) or if the stage reached its max position (25). When the test is complete the stage will automatically raise itself. 4 A window will pop-up and ask for a location for the results. Save in designated location. When typing in the file name place a.txt after the name. This will make the data a text file, which will be needed for data analysis. 5 Click the Red stop sign button in the top left corner of the labview program. 6 If finished running tests, following the test carefully place the load cell pins into the load cell. If not finished you may leave pins out but be cautious.
11 Title: Membrane Press Procedure Page 11 of 14 7 Open the Data Analysis Excel spreadsheet. 8 Open the text file you previously saved. Click Ctrl+A and then Ctrl+C 9 Paste this data into the excel spreadsheet. 10 Click Process Data button on the excel spreadsheet. 11 Record the Young s Modulus value and R 2 into Attachment When closing out Excel, click No to save changes. Do the same for the LabVIEW programs. HISTORY Revision A: DCR- Original.
12 Title: Membrane Press Procedure Page 12 of 14 Attachment 1: Alignment Table Operator: Date: X-Direction Y-Direction After Test # Left side Right side Center After Test # Bottom Top Center
13 Title: Membrane Press Procedure Page 13 of 14 Attachment 2: Young s Modulus Table Operator: Date: Test # Young's Modulus (N/mm 2 ) R
14 Title: Membrane Press Procedure Page 14 of 14 Attachment 3: Packing the device into the case.
Konza District Pinewood Derby Track Parts And Assembly Instructions
Konza District Pinewood Derby Track Parts And Assembly Instructions - 1 - Pinewood Derby Track Parts List: Box 1 of 3 2 each - Race Track Flat Sections 1 each - Race Track Finish Line Section 1 each -
More informationQuick Start Guide. A. Hardware installation B. Software installation C. Start the software for the first time D. Do your first measurement
Quick Start Guide This Quick Start Guide describes the hardware and software installation process and the Measurement feature in a simple way. Please follow the sequence of the steps to avoid problems
More informationOPERATION MANUAL DIVE CALIPER NOT SCALE / IF IN DOUBT ASK* *ALL UNITS IN MM/DEGREES UNLESS SPECIF. Dive Caliper General DC-051
NOT SCALE / IF IN DOUBT ASK* DIVE CALIPER OPERATION MANUAL *THIS INFORMATION IS THE PROPERTY OF ZEBRA-TECH LTD. ALL RIGHTS RESERVED.* *ALL UNITS IN MM/DEGREES UNLESS SPECIF SURFACE F 3.2 Ra UNLESS S Part
More informationTru Flight TRUFLIGHT INSTALLATION GUIDE TRUGOLF.COM
Tru Flight T R A C K I N G S Y S T E M TRUFLIGHT INSTALLATION GUIDE TRUGOLF.COM TruFlight Camera Tracking System Setup & Installation TruFlight : How It Works... 1 TruFlight Components... 1 TruFlight Installation...
More informationFigure SM1: Front panel of the multipatcher software graphic user interface (GUI) at the beginning of multipatcher operation.
APPENDIX 2. Multipatcher Software Setup and Operation. The multipatcher program is organized into four panels. There are controls that allow the user to specify various parameters into the system. The
More informationSetting Up the Ingenico isc250 Pinpad via USB
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Setting Up the Ingenico isc250 Pinpad via USB The following
More informationEndo-Flush Order # ZUTR30004 OPERATION MANUAL. Zutron Medical, LLC W 98 th St #40-27 Lenexa, KS Phone Fax
OPERATION MANUAL Zutron Medical, LLC 17501 W 98 th St #40-27 Lenexa, KS 66219 Phone 877-343-5873 Fax 913-967-5944 ZUT-Lab-004-30004 REV. 03312017 Table of Contents 2 Introduction 1. Intended Use 2. Labels,
More informationAerobic Respiration. Evaluation copy
Aerobic Respiration Computer 17 Aerobic cellular respiration is the process of converting the chemical energy of organic molecules into a form immediately usable by organisms. Glucose may be oxidized completely
More informationMASK INTEGRITY TEST ACCESSORY (MITA) MODEL 8120
MASK INTEGRITY TEST ACCESSORY (MITA) MODEL 8120 QUICK START GUIDE P/N 6006154, REVISION C MAY 2013 Model 8120 Mask Integrity Tester is patented under U.S. Patent No. 8,312,761. Additional patents are pending.
More informationSetting up the Ingenico isc250 Pinpad via USB in Windows 8
One Blue Hill Plaza, 16 th Floor, PO Box 1546 Pearl River, NY 10965 1-800-PC-AMERICA, 1-800-722-6374 (Voice) 845-920-0800 (Fax) 845-920-0880 Setting up the Ingenico isc250 Pinpad via USB in Windows 8 The
More informationicreasepro Creaser Operators Manual
6-2013 Version 3.0 icreasepro Creaser Operators Manual WWW.MBMCORP.COM 800-223-2508 TABLE OF CONTENTS SPECIFICATIONS.1a SAFETY PROCEDURES/CARE & MAINTENANCE..1b COMPONENT IDENTIFICATION 2 TOUCH SCREEN
More informationPROPORTIONING VALVE. Model 150 INSTRUCTION MANUAL. March 2017 IMS Company Stafford Road
PROPORTIONING VALVE Model 150 INSTRUCTION MANUAL March 2017 IMS Company 10373 Stafford Road Telephone: (440) 543-1615 Fax: (440) 543-1069 Email: sales@imscompany.com 1 Introduction IMS Company reserves
More informationInstructions for Assembly, Installation, and Operation of the Gas Addition Kit Accessory with the CEM Discover Systems
Corporation Issued: 5/09 P/N: 600104 Rev. 2 Instructions for Assembly, Installation, and Operation of the Gas Addition Kit Accessory with the CEM Discover Systems The Gas Addition Accessory permits the
More informationCONSUMER MODEL INSTALLATION GUIDE
CONSUMER MODEL INSTALLATION GUIDE System requirements Windows System Requirements To use your TOMI and its software, your system should have: A Microsoft Windows compatible PC with a Pentium IV processor
More informationISE-730 Oxygen Electrode and DO2-100 Currentto-Voltage
Technical Note ISE-730 and DO2-100 Overview In 1954, Dr. Leland Clark invented the first membrane-covered electrode designed to measure the concentration of oxygen in blood, or solution. This electrode
More informationUsing the Akta Prime plus October 22, 2012
Some starting precautions: 1. Vacuum filter all buffers. Removes any large particles/debris that may clog your column De-gases the buffers 2. Clarify lysates first by centrifugation and then filtration
More informationBoyle s Law: Pressure-Volume Relationship in Gases
Boyle s Law: Pressure-Volume Relationship in Gases The primary objective of this experiment is to determine the relationship between the pressure and volume of a confined gas. The gas we will use is air,
More informationUser Manual GRI- 1500Li
User Manual GRI- 1500Li Your Cart Tek caddy cart was thoroughly quality control checked and road tested before being shipped to your address. We do everything possible to assure that your caddy is in perfect
More informationANALOG PRESSURE GAUGE
304-00103 ANALOG PRESSURE GAUGE CALIBRATION PROCEDURE BARFIELD P/N 304-00103 20-304-00103 August 6, 2013 BARFIELD, INC. Corporate Headquarters 4101 Northwest 29th Street Miami, Florida 33142 www.barfieldinc.com
More informationMaintenance Manual. Note: This document is broken up into the following 6 sections of prescribed maintenance.
How to Perform Maintenance On LPKF Circuit Board Plotters Requirements - LPKF Circuit Board Plotter - BoardMaster Software - 2.5 mm Allen wrench (for earlier model machines) - 3mm Allen Wrench - 4mm Allen
More informationBASIC Z-STACK AND TIME SERIES SCAN ON THE ZEISS LIGHTSHEET Z. 1
BASIC Z-STACK AND TIME SERIES SCAN ON THE ZEISS LIGHTSHEET Z. 1 The front door of the main body of the instrument may be open when you arrive. Take the sample chamber and slide it into position with the
More informationRead this first. Zetasizer nano series Self installation and Quick start guide MRK825-02
! Read this first Zetasizer nano series Self installation and Quick start guide I N S T R U M E N T S MRK825-02 Zetasizer Nano series Self installation and Quick start guide MAN0383 Issue 1.1 July 2007
More informationMJB4 Mask Aligner Operating Procedure. Effective Date: 07/12/2012 Author(s): Jiong Hua Phone:
MJB4 Mask Aligner Operating Procedure Effective Date: 07/12/2012 Author(s): Jiong Hua Phone: 402-472-3773 Email: jhua2@unl.edu 1 1 Introduction 1.1 Key Words Karl Suss MJB4 Mask Aligner, Optical Lithography,
More informationHPICAL Operation & Data Logging Procedures. Click spacebar to advance through slides 1
HPICAL-15000 Operation & Data Logging Procedures Click spacebar to advance through slides 1 WARNING Always wear proper safety equipment when using high pressure equipment. Do not exceed 125 psi air pressure.
More informationAngstrom E-Beam Instructions. PROCESS CHECKS: the tooling factors of each metal; Ti/Au layer for wire bonding pull test.
Angstrom E-Beam Instructions Tool Manager: Joe Palmer (jpalmer@princeton.edu) Office: 8-4706; Cell:609-751-1353 Backup: David Barth (dbarth@princeton.edu) Office: 8-4626; Cell: 610-405-8227 PROCESS CHECKS:
More informationShimano Di2 Installation on S5
Installing Shimano Dura Ace Di2 Shifting Systems Note these instructions and pictures are for assembling the Shimano Dura Ace Di2 system (Internal Spec) on the Cervélo S5 frame. The Shimano Ultegra Di2
More informationThe Oxygen Sensor can be connected to all types of einstein Tablets, einstein LabMate, and einstein LabMate +.
The Oxygen sensor is a maintenance- free galvanic oxygen electrode capable of measuring Oxygen in solutions. With built-in temperature compensation, this sensor provides an easy way for students to receive
More informationAngstrom Dielectric Sputterer Operation Manual
Angstrom Dielectric Sputterer Operation Manual I. System overview The Angstrom Dielectric Sputterer (ADS) has a similar interface as the Angstrom metal sputterer. It has two screens, the process screen
More informationINSTRUCTION MANUAL. January 23, 2003, Revision 0
INSTRUCTION MANUAL Model 810A In-Vitro Test Apparatus for 310B Muscle Lever January 23, 2003, Revision 0 Copyright 2003 Aurora Scientific Inc. Aurora Scientific Inc. 360 Industrial Parkway S., Unit 4 Aurora,
More informationWIND CLIPPER KTS ILLUM SCALE INC DEC CLIPPER WIND SYSTEM
CLIPPER WIND KTS ILLUM SCALE DEC INC CLIPPER WIND SYSTEM TABLE OF CONTENTS INTRODUCTION PRE-TEST OF INSTRUMENT INSTALLING THE MASTHEAD SENSOR UNIT INSTALLING THE DISPLAY NORMAL OPERATION CHANGING THE
More informationBante821 Portable Dissolved Oxygen Meter Instruction Manual
Bante821 Portable Dissolved Oxygen Meter Instruction Manual BANTE INSTRUMENTS CO., LTD Bante821 Portable Dissolved Oxygen Meter 1 Introduction Thank you for selecting the Bante821 portable dissolved oxygen
More informationELIMINATOR COMPETITION DRAG RACE Program Manual Firm Ver 4.11
ELIMINATOR COMPETITION DRAG RACE Program Manual Firm Ver 4.11 The Portatree Eliminator Super 2000 Competition Track Timer can be used with an IBM Compatible Personal Computer connected through Com Port
More informationSurvey Technical Support Notes October 2015
Survey Technical Support Notes October 2015 SonarMite with Trimble Access Overview: Trimble Access software, when connected to a SonarMite will store water depths associated with field measurements. Equipment:
More informationGV Standard X-Vent. Setup, Commissioning & Installation Guide
GV Standard X-Vent Setup, Commissioning & Installation Guide Technical experts in the design, manufacture and supply of precision engineered, architectural rooflights for residential and commercial buildings.
More informationTJF-Q180V Cleaning and Disinfection Checklist
TJF-Q180V Cleaning and Disinfection Checklist TJF-Q180V Cleaning and Disinfection Checklist This checklist is used to evaluate and confirm if cleaning and disinfection of the TJF-Q180V has been performed
More informationATOC Meteorological Tower (6 meter-4 level) Guide
ATOC Meteorological Tower (6 meter-4 level) Guide SETUP Outline 1. Siting 2. Components 3. Transportation 4. The Tower 5. The Cables and Data Logger Siting Selecting an appropriate site for the weather
More informationE Lightband Compression Tool Operating Procedure
2002159E Lightband Compression Tool Operating Procedure Organization Name MLB Diameter MLB Assembly Number MLB Assembly Revision MLB Serial Number Instructions: IF LCTS ARE NOT YET INSTALLED ON LIGHTBAND:
More informationBoyle s Law VC 09. Experiment 9: Gas Laws. Abstract
Experiment 9: Gas Laws VC 09 Abstract In this laboratory activity, you will experimentally confirm Boyle s Law, determine absolute zero from Gay-Lussac's Law, and determine the molecular weight of acetone,
More informationThe Gas Laws: Boyle's Law and Charles Law
Exercise 6 Page 1 Illinois Central College CHEMISTRY 130 Name The Gas Laws: Boyle's Law and Charles Law Objective The simple laws governing the properties of gases can be readily demonstrated experimentally.
More informationInstallation Guide, MPower Echelon Console
Installation Guide, MPower Echelon Console AC Performance, AC Sport and AC Performance Plus Schwinn Echelon Console (External Routing) 1. Install batteries to console. Mount the console to the bike. 2.
More informationCover Page for Lab Report Group Portion. Boundary Layer Measurements
Cover Page for Lab Report Group Portion Boundary Layer Measurements Prepared by Professor J. M. Cimbala, Penn State University Latest revision: 30 March 2012 Name 1: Name 2: Name 3: [Name 4: ] Date: Section
More informationTJF-Q180V Cleaning and Disinfection Checklist
TJF-Q180V Cleaning and Disinfection Checklist TJF-Q180V Cleaning and Disinfection Checklist This checklist is used to evaluate and confirm if cleaning and disinfection of the TJF-Q180V has been performed
More informationWickets Administrator
Wickets Administrator Software For Managing Stored Value Wickets 01/08/2008 Product Details And Operating Instructions Overview This page describes each major function of Wickets Administrator in detail.
More informationWarnings: Notes: Revised: October 5, 2015
Karl Suss MA6 Mask Aligner Standard Operating Procedure Faculty Supervisor: Prof. Robert White, Mechanical Engineering (x72210) Safety Office: Peter Nowak x73246 (Just dial this directly on any campus
More informationFireHawk M7 Interface Module Software Instructions OPERATION AND INSTRUCTIONS
FireHawk M7 Interface Module Software Instructions OPERATION AND INSTRUCTIONS WARNING THE WARRANTIES MADE BY MSA WITH RESPECT TO THE PRODUCT ARE VOIDED IF THE PRODUCT IS NOT USED AND MAINTAINED IN ACCORDANCE
More informationA180 DO/BOD/OUR/SOUR Meter Instruction Manual
A180 DO/BOD/OUR/SOUR Meter Instruction Manual BANTE INSTRUMENTS CO., LTD A180 DO/BOD/OUR/SOUR Meter 1 Introduction Thank you for selecting the A180 multiparameter dissolved oxygen meter. This manual provides
More informationMicrosoft Windows Software Manual for FITstep Stream Version 4
Thank you for purchasing this product from Gopher. If you are not satisfied with any Gopher purchase for any reason at any time, contact us and we will replace the product, credit your account, or refund
More informationDissolved Oxygen Sensor
Instruction Manual 499ADO and 499ADO-VP LIQ_MAN_ABR_499ADO May 2014 Dissolved Oxygen Sensor CAUTION For additional information, please visit our website at www.rosemountanalytical.com SENSOR/PROCESS APPLICATION
More informationRace Screen: Figure 2: Race Screen. Figure 3: Race Screen with Top Bulb Lock
Eliminator Competition Stand Alone Mode - Instruction Manual Main Menu: After startup, the Eliminator Competition will enter the Main Menu. Press the right/left arrow buttons to move through the menu.
More informationTo Purchase This Item, Visit BMI Gaming (800)
How to play the game How to play the game The object of the game is to reach the Game Goal before your opponent. HOW TO START: - A coin toss decides who starts the game. The winner of the coin toss also
More informationApproach. owner s manual
Approach owner s manual 2009 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151 st Street, Olathe, Kansas 66062, USA Tel. (913) 397.8200 or (800) 800.1020 Fax (913) 397.8282 Garmin
More informationStandard Operating Procedure Porosity Analyzer - The Micromeritics Tri-Star II (surface area) with Micrometrics VacPrep 061 (Sample Degas System)
Standard Operating Procedure Porosity Analyzer - The Micromeritics Tri-Star II (surface area) with Micrometrics VacPrep 061 (Sample Degas System) The Micromeritics Tri-Star II Surface Area and Porosity
More informationMicrofluidic Demonstration
Microfluidic Demonstration Co-flow of liquids across a microfluidic chip Create a microfluidic controller to flow liquids across a microfluidic chip. 1. Assemble fluidic circuits and attach to breadboard.
More informationOptical Dissolved Oxygen Meter
Optical Dissolved Oxygen Meter HI764113 Rugged Optical Dissolved Oxygen Probe for Fresh and Saltwater Applications Digital, weighted probe No membranes No electrolytes No oxygen consumption No flow dependence
More informationPresents the following instructional slide show:
Presents the following instructional slide show: Operating Procedures for the Sure Shot Acoustic Fluid Level System. Sure Shot Acoustic Fluid Level System Well head attachment and accessories Complete
More informationOWNER S MANUAL. All PowaKaddy electric trolleys have been awarded the Quiet Mark by the Noise Abatement Society
OWNER S MANUAL All PowaKaddy electric trolleys have been awarded the Quiet Mark by the Noise Abatement Society Thank you for purchasing the new PowaKaddy. We hope you enjoy your new FW7s GPS trolley and
More informationVROC (Viscometer/ Rheometer-on-a-Chip) User s Manual 1
VROC (Viscometer/ Rheometer-on-a-Chip) User s Manual 1 2 Table of Contents 1. Unpacking 4 2. Precautions 6 3. Hardware Setup 7 4. Sample Loading 8 5. Loading the Syringe on the Pump 9 6. Chip to the Syringe
More informationMisaligned Folds Paper Feed Problems Double Feeds Won t Feed FLYER Won t Run iii
Operator s Manual Table of Contents Operator Safety... 1 Introduction... 2 Unpacking and Setup... 3 Unpacking... 3 Setup... 4 FLYER Overview... 5 FLYER Diagram... 5 Capabilities... 5 Control Panel... 6
More informationApproach. S3 Owner s Manual. May _0B Printed in Taiwan
Approach S3 Owner s Manual May 2012 190-01467-00_0B Printed in Taiwan All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin.
More informationTranspiration. DataQuest OBJECTIVES MATERIALS
Transpiration DataQuest 13 Water is transported in plants, from the roots to the leaves, following a decreasing water potential gradient. Transpiration, or loss of water from the leaves, helps to create
More informationSOLUBILITY OF A SOLID IN WATER
1516L Experiment 1 SOLUBILITY OF A SOLID IN WATER Objectives In this experiment you will determine the solubility of potassium nitrate (KNO 3 ) in water at various temperatures. You will prepare a plot
More informationCircuFlow Quick Setup Guide
CircuFlow 5200 Quick Setup Guide LB04.0001 Rev B 20140314 TABLE OF CONTENTS Setup Therapy Setup Gradient Mode Pressure Mode Lock Device Unlock Device Treatment 03 04 05 08 11 12 13 02 SETUP 01 01 Open
More informationQUICK START GUIDE TO DRINKING WATER MONITORING
APPENDIX F QUICK START GUIDE TO DRINKING WATER MONITORING Introduction: This Quick Start guide is designed to allow users who are already familiar with the basic use of YSI 6-series sondes for surface
More information256 Pneumatic Pressure Indicator
256 Pneumatic Pressure Indicator 51425699 Copyright 2002 Slope Indicator Company. All Rights Reserved. This equipment should be installed, maintained, and operated by technically qualified personnel. Any
More informationGPS OWNERS MANUAL. All PowaKaddy electric trolleys have been awarded the Quiet Mark by the Noise Abatement Society
OWNERS MANUAL GPS All PowaKaddy electric trolleys have been awarded the Quiet Mark by the Noise Abatement Society The PowaKaddy Update App Available to download from the Apple App store and Google Play
More informationRead Before Operating!
Read Before Operating! IMPORTANT OPERATING INSTRUCTIONS THE DEUCE PITCHING MACHINE THROWS REAL REGULATION BALLS; HOWEVER, THE ACCURACY OF THE DEUCE DEPENDS ON THE QUALITY, HARDNESS AND TYPE OF BALLS YOU
More informationVOLAR PRODUCTION TRUCK SCOREBOARD CONTROLLER DATA INTEGRATION
VOLAR PRODUCTION TRUCK SCOREBOARD CONTROLLER DATA INTEGRATION INTRODUCTION» In an effort to reduce duplicate data entry and improve the accuracy of that data, Production Truck allows users to integrate
More informationRM-80 respiration monitor
RM-80 respiration monitor User Manual September 18, 2015 0025-003M 950 North Hague Avenue Columbus, Ohio 43204-2121 USA Sales: sales@colinst.com Service: service@colinst.com Phone: (614) 276-0861 Fax:
More informationExperiment C-6 Gas Solubility
1 Experiment C-6 Gas Solubility Objectives To measure dissolved oxygen in water by using an oxygen sensor. To learn about physical factors that influence oxygen solubility in water. To examine the dissolved
More informationDeskCycle USER S MANUAL. Ellipse QUESTIONS / PROBLEMS. Order# Support and Contact: See the support link at DeskCycle.com
DeskCycle Ellipse USER S MANUAL Visit us at www.deskcycle.com for: Usage Tips Calorie Calculator Accessories And More QUESTIONS / PROBLEMS Order# Support and Contact: See the support link at DeskCycle.com
More informationOxygen Sensor with Electrode
imagine explore learn Oxygen Sensor with Electrode Product Number: ENOXY-A222 Overview The Oxygen sensor is a maintenance-free galvanic oxygen electrode, capable of measuring Oxygen both in the air and
More informationTANK MANAGER FOR TWO TANKS OPERATING MANUAL. 10/31/11 C-More T6C L color touch panel
TANK MANAGER FOR TWO TANKS OPERATING MANUAL 10/31/11 C-More T6C L color touch panel 1 TABLE OF CONTENTS GENERAL...3 INSTALLATION...4 STONE TEST PROCEDURE...7 OPERATIONAL SUMMARY...7 AUTO CARBONATION...10
More informationMULTITUBE BUBBLE TUBE BY ROMPA (U)
Page 1 of 16 MULTITUBE BUBBLE TUBE BY ROMPA 19781 (U) CONTENTS 1 x Base Unit (chassis) 1 x Base Cover (white plastic cover) 1 x Multitube Bubble Tube Column 1 x Bubble Tube Cap 1 x Power Supply (black
More informationBY HYDROHOIST BOATLIFTS
BY HYDROHOIST BOATLIFTS OWNER S MANUAL US PATENT # 6,422,167 B1 REVISED: June 21st 2018 800.825.3379 BOATLIFT.COM Thank You We would like to a moment to thank you for purchasing a HarborHoist TM G1.5 lift.
More informationVapor Pressure of Liquids
Vapor Pressure of Liquids In this experiment, you will investigate the relationship between the vapor pressure of a liquid and its temperature. When a liquid is added to the Erlenmeyer flask shown in Figure
More informationSS32L Dissolved O 2 Probe
BIOPAC WWW.biopac.com Systems, Inc. Application Note PH-185 SS32L Dissolved O 2 Probe SS32L Dissolved O 2 Probe BIOPAC Software SS32L Specifications BSL PRO v. 3.6.6 BIOPAC Hardware SS32L Dissolved O 2
More informationOWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL)
OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) Table of Contents ASSEMBLY ASSEMBLY Pistol Bullet Feeder... Page 3 CHANGE-OVERS The Hornady Lock-N-Load Pistol Bullet Feeder is capable of feeding most
More informationPegas 4000 MF Gas Mixer InstructionManual Columbus Instruments
Pegas 4000 MF Gas Mixer InstructionManual Contents I Table of Contents Foreword Part I Introduction 1 2 1 System overview... 2 2 Specifications... 3 Part II Installation 4 1 Rear panel connections...
More informationOperator Quick Guide ORBISPHERE 3654
Operator Quick Guide ORBISPHERE 3654 Revision H - 14/03/2008 Operating Information About this Guide The information in this guide has been carefully checked and is believed to be accurate. However, Hach
More informatione360t and e360t+ Model
Addendum 1 e360t and T Model Addendum e360t+ Model Congratulations on your purchase of the Newport TM e360t Ventilator. This package includes an addendum to the Newport e360 Ventilator Operating Manual
More informationTether Tender. User Manual. Revision 1A. KCF Technologies, Inc. 336 South Fraser St., State College, PA
Tether Tender User Manual Revision 1A KCF Technologies, Inc. 336 South Fraser St., State College, PA 16801 www.kcftech.com 814.867.4097 1. CONTENTS 1. Contents... 2 2. Introduction... 3 3. Care and Handling
More informationEXPERIMENT 12 GAS LAWS ( BOYLE S AND GAY-LUSSAC S LAW)
EXPERIMENT 12 GAS LAWS ( BOYLE S AND GAY-LUSSAC S LAW) INTRODUCTION: In order to specify fully the condition of a gas it is necessary to know its pressure, volume, and temperature. This quantities are
More informationArmfield Distillation Column Operation Guidelines
Armfield Distillation Column Operation Guidelines 11-2016 R.Cox Safety SAFETY GLASSES ARE REQUIRED WHEN OPERATING THE DISTILLATION COLUMN Wear gloves when mixing alcohol feedstock The column will become
More informationNEULOG OXYGEN LOGGER SENSOR GUIDE
NeuLog oxygen logger sensor NUL-205 The oxygen sensor can be used for any science experiment or activity where oxygen levels, dissolved or gaseous, are required. Some fields of study include Chemistry,
More informationWire Buddy Manual IOpath Software
Wire Buddy Manual IOpath Software Wire Buddy is a calculation reference tool for Electricians and Maintenance personnel. Wire Buddy was created for the Maintenance Electrician. There are many occasions
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationDIVE MEET SCORING INSTRUCTIONS. Day before meet
DIVE MEET SCORING INSTRUCTIONS Day before meet Physical set up Set up registration/scoring table #1 on 1 meter side and scoring table #2 on 3 meter side of diving well, judges chairs, and award stand as
More informationMounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser
Mounting the RoboFocus RF-3 Unit on the LX-200/400 MicroFocuser The RoboFocus unit can be mounted on the Meade MicroFocuser, commonly found on the LX-200/400 series. The RF folks point to this URL as a
More informationSERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.
SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding
More informationWELCOME TO THE REVOLUTION
USER GUIDE WELCOME TO THE REVOLUTION THANK YOU FOR CHOOSING THE GCQUAD We listened to what you wanted - and created the most accurate, versatile and game-enhancing ball and club analysis solution available
More informationUnderwater Housing for Canon EOS M
Underwater Housing for Canon EOS M User Manual 1 Table of Contents 1. Introduction 2. Specifications 3. Function Controls 4. Set up Instructions 5. Use & Care of Housing 6. Service 7. Warranty 1. Introduction
More informationInstallation, Operation, and Maintenance Manual
Installation, Operation, and Maintenance Manual Welker The information in this manual has been carefully checked for accuracy and is intended to be used as a guide for the installation, operation, and
More informationSET-UP INSTRUCTIONS. Includes:» Lightning Strike with Ball Shagger Feeder» 6 Lightning Strike Balls» 6 Volt AC Adapter
SET-UP INSTRUCTIONS Includes:» Lightning Strike with Ball Shagger Feeder» 6 Lightning Strike Balls» 6 Volt AC Adapter BEFORE YOU BEGIN:» Make sure you have all of the Lightning Strike components. Please
More informationLEO 1525 FEG SEM Standard Operating Procedures Mar. 6, 2012 For additional assistance, please contact the facility manager.
LEO 1525 FEG SEM Standard Operating Procedures Mar. 6, 2012 For additional assistance, please contact the facility manager. Please contact in case of emergency: SEM microscopist: Mr. Eric Miller, 7-0789
More informationRB70 Automatic Diluent Valve Maintenance Manual. Version 1.1 November 2006 Written by Tino de Rijk. Page 1 of 23
RB70 Automatic Diluent Valve Maintenance Manual Version 1.1 November 2006 Written by Tino de Rijk Page 1 of 23 Table of Contents 1. Introduction... 3 2. ADV diagram and parts list (Pre June 2006)... 4
More informationSuperconducting Susceptometer (MPMS-5S) Quantum Design Room 296 (MPMS)
Superconducting Susceptometer (MPMS-5S) Quantum Design Room 296 (MPMS) Sensitivity: 1x10 11 A m 2 Applied DC fields: 0 T to 5 T Applied AC fields: 0 G to 3 G (zero-to-peak), 0.01 Hz to 1000 Hz Temperatures
More informationMRF SERIES. Instruction Manual
MRF SERIES Instruction Manual BEFORE USING THIS PRODUCT, CAREFULLY READ THOUGH MANUAL AND RETAIN IT FOR FUTURE REFERENCE. ECHO1USA AUTOMATIC ELECTRIC GUNS ARE INTENDED FOR AGES 18 AND ABOVE. THIS PRODUCT
More informationRocky Mountain Instinct / Pipeline Frame Assembly Guide. Date: March 31, 2017
Rocky Mountain Instinct / Pipeline Frame Assembly Guide Date: March 31, 2017 1 Table of Contents Front Triangle Preparation... 4 Parts Needed... 4 Instructions... 4 Chain Stay Preparation... 6 Parts Needed...
More informationSTATEMENT OF LIABILITY
STATEMENT OF LIABILITY LASERLINE IS MANUFACTURED BY WEST INDUSTRIES INC. LASERLINE IS PATENTED AND TRADEMARKED. This device is not a toy. Misuse may cause serious injury. The user and any person within
More informationPR4 Installation, Operation & Maintenance Instructions (DOT Certification Included)
PR4 Installation, Operation & Maintenance Instructions (DOT Certification Included) March 2006 Form FVC 054 Rev. 6 KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER. The Passive - R4 device
More information