SAFETY DATA SHEET. Product Number C-139. Effective Date 10/17/2018

Transcription

1 1. Product and Company Identification SAFETY DATA SHEET Product Number C-139 Product Name De Aqua Lube Effective Date 10/17/2018 Company Information Baton Rouge Industries, Inc Groom Rd. Baker, La Telephone US Emergency Telephone outside US Version # Hazards Identification Physical hazards Flammable aerosols Category 1 Health hazards Sensitization, skin Category 1 Reproductive toxicity (fertility) Category 2 Aspiration hazard Category 1 OSHA defined hazards t classified Label elements Signal Word Hazard statement Precautionary Statement Prevention Response Danger Extremely flammable aerosol. May be fatal if swallowed and enters airways. May cause an allergic skin reaction. Suspected of damaging fertility. Obtain special instructions before use Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. smoking. Do not spray on an open flame or other ignition source. Pressurized container. Do not pierce or burn even after use. Avoid breathing gas. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves/protective clothing/eye protection/face protection. If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting If on skin: Wash with plenty of water. If exposed or concerned: get medical advice/attention. If skin irritation or rash occurs: Get medical advice/attention. Wash contaminated clothing before reuse

2 Storage Disposal Hazard(s) not otherwise classified (HNOC) Supplemental Information Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50 C/122 F Dispose of contents/container in accordance with local/regional/national/international regulations. Combustible ne 3. Composition/information on ingredients Mixtures Chemical Name Common name and CAS number % synonyms White mineral oil Carbon Dioxide Dipropylene Glycol Monomethyl Ether Octamethylcyclotetrasiloxane Sulfonic Acids, petroleum, calcium salts Other components below reportable levels First-aid measures Inhalation Skin contact Eye contact Ingestion Most important symptoms/effects, acute and delayed Indication of immediate medical attention and special treatment needed General Information Move to fresh air. Call a physician if symptoms develop or persist. In case of eczema or other skin disorders: Seek medical attention and take along these instructions. Rinse with water. Get medical attention if irritation develops or persists. Rinse mouth. Get medical attention if symptoms occur. Aspiration may cause pulmonary edema and pneumonitis. May cause allergic skin reaction. Dermatitis. Rash. Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed. IF exposed or concerned: Get medical advice/attention. If you feel unwell, seek medical advice (show the label where possible). Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Show this safety data sheet to the doctor in attendance. Wash contaminated clothing before reuse. 2 P a g e

3 5. Fire-fighting measures Suitable extinguishing media Unsuitable extinguishing media Specific hazards arising from the chemical Special protective equipment and precautions for firefighters Firefighting equipment/instructions Specific Methods General fire hazards Foam. Dry Chemicals. Carbon Dioxide (CO2) Do not use water jet as an extinguisher, as this will spread the fire. Contents under pressure. Pressurized container may explode when exposed to heat or flame. During fire, gases hazardous to health may be formed. Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. Move containers from fire area if you ca do so without risk. Cool containers exposed to heat with water spray and remove container, if o risk is involved. Containers should be cooled with water to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or monitor nozzles, if possible. If not withdraw and let fire burn out. Use standard firefighting procedures and consider the hazards of other involved materials. Move containers from fire area if you can do so without risk. In the event of fire and/or explosion do not breathe fumes. Extremely flammable aerosol. Combustible. 6. Accidental release measures Personal precautions, protective equipment and emergency procedures Methods and materials for containment and cleaning up Environmental precautions Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear appropriate protective equipment and clothing during clean-up. Avoid breathing gas. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so without risk. Move the cylinder to a safe and open area if the leak is irreparable. Isolate area until gas has dispersed. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Following product recovery, flush area with water. For waste disposal, see section 13 of the SDS. Avoid discharge into drains, water courses, or onto the ground. 7. Handling and storage Precautions for safe handling Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed 3 P a g e

4 Conditions for safe storage, including any incompatibilities surface is thoroughly dry. Do not cut, weld, solder, drill, grind or expose containers to heat, flame, sparks, or other sources of ignition. All equipment used when handling the product must be grounded. Do not re-use empty containers. Avoid breathing gas. Avoid contact with eyes, skin, and clothing. Avoid prolonged or repeated contact with skin. Avoid prolonged exposure. Pregnant or breastfeeding women must not handle this product. Should be handled in closed systems, if possible. Use only in well ventilated areas. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Observe good industrial hygiene practices. Level 1 Aerosol Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50 C/122 F. Do not puncture, incinerate, or crush. Do not handle or store near an open flame, heat, or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Store away from incompatible materials (see Section 10 of the SDS) 8. Exposure controls/personal protection Occupational Exposure limits US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR ) Components Type Value Carbon Dioxide (CAS ) PEL 9000 mg/m3 Dipropylene Glycol Monomethyl Ether (CAS ) PEL 5000 ppm 600 mg/m3 100ppm US ACGIH Threshold Limit Values Components Type Value Carbon Dioxide (CAS ) STEL 30000ppm TWA 5000ppm Dipropylene Glycol Monomethyl Ether (CAS ) STEL TWA 150ppm 100ppm 4 P a g e

5 US. NIOSH: Pocket Guide to Chemical Hazards Components Type Value STEL mg/m3 Carbon Dioxide (CAS ) Dipropylene Glycol Monomethyl Ether (CAS ) TWA STEL TWA US. Workplace Environmental Exposure Level (WEEL) Guides ppm 9000 mg/m ppm 900 mg/m3 150 ppm 600 mg/m3 100 ppm Components Type Value Octamethylcyclotetrasiloxane (CAS ) TWA 10 ppm Biological limit values biological exposure limits noted for the ingredient(s) Exposure guidelines US California EOLs: Skin designation o Dipropylene Glycol Monomethyl Ether (CAS ) Can be absorbed through the skin. US Tennessee OELs: Skin designation o Dipropylene Glycol Monomethyl Ether (CAS ) Can be absorbed through the skin. US ACGIH Threshold Limit Values: Skin designation o Dipropylene Glycol Monomethyl Ether (CAS ) Can be absorbed through the skin. US NIOSH Pocket guide to Chemical Hazards: Skin designation o Dipropylene Glycol Monomethyl Ether (CAS ) Can be absorbed through the skin. US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR ) o Dipropylene Glycol Monomethyl Ether (CAS ) Can be absorbed through the skin. 5 P a g e

6 Appropriate engineering controls Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Individual protection measures, such as personal protective equipment Eye/face protection Chemical goggles are recommended. Skin protection o Hand protection Wear appropriate chemical resistant gloves. Suitable gloves can be recommended by the glove supplier. o Other Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended. Respiratory protection If permissible levels are exceeded use NIOSH mechanical filter/organic vapor cartridge or an airsupplied respirator. Thermal hazards Wear appropriate thermal protective clothing, when necessary. General hygiene considerations Observe any medical surveillance requirements. When using do not smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Contaminated work clothing should not be allowed out of the workplace. 9. Physical and chemical properties Appearance Physical state Form Color Odor Odor threshold ph Melting point/freezing point Initial boiling point and boiling range Flash Point Evaporation point Flammability (solid, gas) Gas Aerosol F (149.4 C) estimated 6 P a g e

7 Upper/lower flammability or explosive limits Flammability limit lower (%) Flammability limit upper (%) Explosive limit lower (%) Explosive limit upper (%) Vapor pressure Vapor density Relative density Solubility(ies) 0.5% estimated 4.4% estimated t available t available F estimated Solubility (water) Partition coefficient (n-octanol/water) Auto-ignition temperature Decomposition temperature Viscosity Other information Explosive properties Oxidizing properties t explosive t oxidizing 10. Stability and reactivity Reactivity Chemical stability Possibility of hazardous reactions Conditions to avoid Incompatible materials Hazardous decomposition products The product is stable and non-reactive under normal conditions of use, storage, and transport. Material is stable under normal conditions Hazardous polymerization does not occur Keep away from heat, sparks, and open flame. Contact with incompatible materials Strong oxidizing agents. hazardous decomposition products are known. 11. Toxicological information Information on likely routes of exposure Inhalation Skin contact Symptoms related to the physical, chemical, and toxicological characteristics Information on toxicological effects Acute toxicity Prolonged inhalation may be harmful May cause an allergic skin reaction Direct contact with eyes may cause temporary irritation. Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia Aspiration may cause pulmonary edema and pneumonitis. May cause an allergic skin reaction. Dermatitis. Rash May be fatal if swallowed and enters airways. May cause an allergic skin reaction. 7 P a g e

8 Components Species Test Results Dipropylene Glycol Monomethyl Ether (CAS ) Acute Dermal LD50 Rabbit Rat 9510 mg/kg, 24 hours 10 ml/kg, 24 hours >19020 mg/kg, hours >20 ml/kg, hours Inhalation LD50 Rat >553 ppm, 8 hours >275 ppm, 7 hours Oral LD50 Dog Rat 7.5 ml/kg >5000 mg/kg 5.4 ml/kg Octamethylcyclotetrasiloxane (CAS ) Acute Dermal LD50 Rat >2000 mg/kg, 24 hours Inhalation Aerosol LC50 Rat 36 mg/l, 4 hours Oral LD50 Acute Dermal LD50 Mouse 1700 mg/kg Rat >4800 mg/kg Sulfonic Acids, Petroleum, Calcium Salts (CAS ) Rabbit Rat >4000 mg/kg, 24 hours >2000 mg/kg, 24 hours Inhalation LC50 Rat >1.9 mg/l, 4 hours Oral LD50 Rat >5000 mg/kg White Mineral Oil (CAS ) Acute Dermal LD50 Rabbit >2000 mg/kg, 24 hours Inhalation LC50 Rat 2.18 mg/l, 4 hours Oral LD50 Rat >5000 mg/kg *Estimates for product may be based on additional component data not shown 8 P a g e

9 Skin corrosion/irritation Serious eye damage/eye irritation Respiratory or skin sensitization Respiratory sensitization Skin sensitization Germ cell mutagenicity Carcinogenicity Prolonged skin contact may cause temporary irritation. Direct contact with eyes may cause temporary irritation t a respiratory sensitizer May cause an allergic skin reaction data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA IARC Monographs Overall Evaluation of Carcinogenicity OSHA Specifically Regulated Substances (29 CFR ) US. National Toxicology Program (NTP) Report on Carcinogens t listed t listed Reproductive toxicity Specific target organ toxicity single exposure Specific target organ toxicity repeated exposure Aspiration hazard Chronic effects Suspected of damaging fertility t classified t Classified May be fatal if swallowed and enters airways Prolonged inhalation may be harmful 12. Ecological information Ecotoxicity The product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment Persistence and degradability data is available on the degradability of this product Bioaccumulative potential data available mobility in soil Other adverse effects other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. 13. Disposal considerations Disposal instructions Local disposal regulations Hazardous waste code Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Contents under pressure. Do not puncture, incinerate, or crush. Dispose of contents/container in accordance with local/regional/national/international regulations. Dispose in accordance with all applicable regulations The waste code should be assigned in discussion between the user, the producer, and the waste disposal company. 9 P a g e

10 Waste from residues/unused products Contaminated packaging 14. Transport Information Dispose of in accordance with local regulations. Empty containers or liners may retain some product residues. This material and its container must be disposed of in a safe manner (see: Disposal instructions) Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal. Do not re-use empty containers. DOT IATA IMDG UN number UN proper shipping name Transport hazard class(es) Class Subsidiary risk Label(s) Packing group Special precautions for user Special provisions Packaging exceptions Packaging non bulk Packaging bulk UN number UN proper shipping name Transport hazard class(es) Class Subsidiary risk Label(s) Packing group Environmental hazards ERG Code Special precautions for user Other information Passenger and cargo aircraft Cargo aircraft only Packaging Exceptions UN number UN proper shipping name Transport hazard class(es) Class Subsidiary risk Label(s) Packing group UN1950 Aerosols, flammable, (each not exceeding 1 L capacity) t applicable t available N ne ne UN1950 Aerosols, flammable t applicable 10L Read safety instructions, SDS and emergency procedures before handling. Allowed with restrictions Allowed with restrictions LTD QTY UN19850 AEROSOLS ne t Applicable 10 P a g e

11 Environmental hazards Marine pollutant EmS Special precautions for user Packaging exceptions Transport in bulk according to Annex II of MARPOL 73/78 and the IBC CODE F-D, S-U Read safety instructions, SDS, and emergency procedures before handling LTD QTY t applicable DOT IATA; IMDG 15. Regulatory information US Federal regulations This product is a Hazardous Chemical as defined by the OSHA Hazard Communication Standard, 29 CFR TSCA Section 12 (b) Export tification (40 CFR 707, Subpt. D) CERCLA Hazardous Substance List (40CFR 302.4) t listed SARA 304 Emergency release notification OSHA Specifically Regulated Substances (29 CFR ) Superfund Amendments and Reauthorization Act of 1986 (SARA) Hazard categories Immediate Hazard Yes Delayed Hazard Yes Fire Hazard Yes 11 P a g e

12 Pressure Hazard Yes Reactivity Hazard SARA 302 Extremely hazardous substance SARA 311/312 Hazardous chemical SARA 313 (TRI reporting) Other federal regulations Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Clean Air Act (CAA) Section 112 (r) Accidental Release Prevention (40 CFR Safe Drinking Water Act (SDWA) US state regulations US. California Controlled Substances. CA Department Justice (California Health and Safety Code Section 11100) of t listed t listed US. California. Candidate Chemicals List Safety Consumer Products Regulations (Cal. Code Regs, tit, 22, , subd. (a)) US. Massachusetts RTK Substance List US. New Jersey Worker and Community Right-to- Know Act US. Pennsylvania Worker and Community Right-to- Know Law US. Rhode Island RTK Octamethylcyclotetrasiloxane (CAS ) Carbon Dioxide (CAS ) Dipropylene Glycol Monomethyl Ether (CAS ) Carbon Dioxide (CAS ) Dipropylene Glycol Monomethyl Ether (CAS ) Carbon Dioxide (CAS ) Dipropylene Glycol Monomethyl Ether (CAS ) US. California Proposition 65 WARNING: This product contains a chemical known to the state of California to cause cancer. US California Proposition 65 CRT: Listed date/carcinogenic substance Myrcene (CAS ) Listed: March 27, P a g e

13 International Inventories Country(s) or region Inventory name On inventory (yes/no)* Australia Australian Inventory of Chemical Substances (AICS) Canada Domestic Substances List (DSL) Yes Canada n-domestic Substances List (NDSL) China Inventory of Existing Chemical Substances in China (IECSC) Europe European Inventory of Existing Commercial Chemical Substances (EINECS) Europe European List of tified Chemical Substances (ELINCS) Japan Inventory of Existing and New Chemical Substances (ENCS) Korea Existing Chemicals List (ECL) New Zealand New Zealand Inventory Philippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) United States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory Yes *A yes indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A no indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s). 16. Other information, including date of preparation or last revision Issue date 10/18/2018 Version # 01 Disclaimer The information provided in this Safety Data Sheet is correct to the best of our knowledge, information, and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal, and release and is not to be considered a warranty or quality specification,, the information relate only to the specific material designated and may not be valid for such material used in combination with other materials or in any process, unless specified in the text. Revision information Product and Company Identification: Alternate Trade names. 13 P a g e