ACCESSORIES MAY BE PURCHASED SEPARATELY.

Size: px

Start display at page:

Download "ACCESSORIES MAY BE PURCHASED SEPARATELY."

Linette Campbell
5 years ago
Views:

SUMMIT # 42377 BUILT-IN NG SIDE BURNER INSTALLATION/OWNER'S GUIDE Summit Built-In NG Side Burner THESE ACCESSORIES MAY BE PURCHASED SEPARATELY.

1 SUMMIT # BUILT-IN NG SIDE BURNER INSTALLATION/OWNER'S GUIDE Summit Built-In NG Side Burner THESE ACCESSORIES MAY BE PURCHASED SEPARATELY. YOU MUST READ THIS OWNERS GUIDE BEFORE OPERATING YOUR GAS GRILL DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flames. 3. Open lid 4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department. Leaking gas may cause a fire or explosion which can cause serious bodily injury or death, or damage to property. WARNING: Follow all leak-check procedures carefully in this manual prior to barbecue operation. Do this even if the barbecue was dealer-assembled. NOTICE TO INSTALLER: These instructions must be left with the owner and the owner should keep them for future use. THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLY. WARNING 1. Do not store spare liquid propane cylinder within 10 feet (3m) of this appliance. 2. Do not store or use gasoline or other flammable liquids or vapors within 25 feet (8m) of this appliance. WARNING: Do not try to light this appliance without reading the "Lighting" Instructions section of this manual US 05/01/04 NG US English

2 DANGERS & WARNINGS DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. WARNINGS Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. After a period of storage, and/or nonuse, the Weber Built-In side burner should be checked for gas leaks and burner obstructions before use. See instructions in this manual for correct procedures. Do not operate the Weber Built-In side burner if there is a gas leak present. Do not use a flame to check for gas leaks. Combustible materials should never be within 24 inches of the top, bottom, back or sides of your Weber Built-In side burner. Do not put a barbecue cover or anything flammable on, or in the storage area under the barbecue. Built-In side burner barbecue should never be used by children. Accessible parts of the barbecue may be very hot. Keep young children away while it is in use. You should exercise reasonable care when operating your Weber Built-In side burner. It will be hot during cooking or cleaning and should never be left unattended, or moved while in operation. Should the burner go out while in operation, turn the gas valve off. Open the lid and wait five minutes before attempting to relight, using the lighting instructions. Never lean over open side burner or place hands or fingers on the front edge of the side burner. Should a grease fire occur, turn off burner and leave lid closed until fire is out. Do not enlarge valve orifices or burner ports when cleaning the valve or burner. The Weber Built-In side burner should be thoroughly cleaned on a regular basis. Liquid propane gas is not natural gas. The conversion or attempted use of natural gas in a liquid propane unit or liquid propane gas in a natural gas unit is dangerous and will void your warranty. Do not attempt to disconnect any gas fitting while your barbecue is in operation. Use heat-resistant barbecue mitts or gloves when operating barbecue. Keep any electrical supply cord and the fuel supply hose away from any heated surfaces. Combustion byproducts produced when using this product contain chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm. Do not use this Built-In side burner unless all parts are in place. The unit must be properly assembled according to the instructions outlined in the Assembly Instruction section of the Owner s Guide. LIQUID PROPANE GAS UNITS ONLY: Use the regulator that is supplied with your Weber gas barbecue. Do not attempt to disconnect the gas regulator or any gas fitting while your barbecue is in operation. A dented or rusty liquid propane cylinder may be hazardous and should be checked by your liquid propane supplier. Do not use a liquid propane cylinder with a damaged valve. Although your liquid propane cylinder may appear to be empty, gas may still be present, and the cylinder should be transported and stored accordingly. If you see, smell or hear the hiss of escaping gas from the liquid propane cylinder: 1. Move away from liquid propane cylinder. 2. Do not attempt to correct the problem yourself. 3. Call your fire department. 2

3 Warranty Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber gas grill that it will be free of defects in material and workmanship from the date of purchase as follows: Stainless Steel Lid, All Remaining Parts, when assembled and operated in accordance with the printed instructions accompanying it. Weber may require reasonable proof of your date of purchase. THERE- FORE, YOU SHOULD RETAIN YOUR SALES SLIP OR INVOICE. This Limited Warranty shall be limited to the repair or replacement of parts that prove defective under normal use and service and which on examination shall indicate, to Weber s satisfaction, they are defective. Before returning any parts, contact the Customer service representative in your region using the contact information sheet provided with your manual. If Weber confi rms the defect and approves the claim, Weber will elect to replace such parts without charge. If you are required to return defective parts, transportation charges must be prepaid. Weber will return parts to the purchaser, freight or postage prepaid. This Limited Warranty does not cover any failures or operating diffi culties due to accident, abuse, misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this owner s manual. Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, discoloration due to exposure to chemicals either directly or in the atmosphere, is not covered by this Limited Warranty. There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and fi tness are limited in duration to the period of coverage of this express written Limited Warranty. Some regions do not allow limitation on how long an implied warranty lasts, so this limitation may not apply to you. Weber is not liable for any special, indirect or consequential damages. Some regions do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. Weber does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on Weber. This Warranty applies only to products sold at retail. WEBER-STEPHEN PRODUCTS CO. Customer Service Center 1890 Roselle Road, Suite 308 Schaumburg, IL USA 10 years 5 years The natural gas supply is easy to use and gives you more cooking control than charcoal fuel. These instructions will give you the minimum requirements for assembling your Weber Built-In Side Burner. Please read the instructions carefully before using your Weber Built-In Side Burner. Improper assembly can be dangerous. Not for use by children. If there are local codes that apply to portable gas grills, you will have to conform to them. If there are no local codes, you must conform to the latest edition of the National Fuel Gas Code: ANSI Z 223.1/NFPA54. WARRANTY 3 This Weber Built-In Side Burner is designed for natural (piped in city) gas only. Do not use liquid propane (LP) bottled gas. The valves, orifi ces and hose are for natural gas only. Do not use with charcoal fuel. Check that the area under the control panel and the bottom tray are free from debris that might obstruct the fl ow of combustion or ventilation air. Storage The gas must be turned OFF at the natural gas supply when the Weber Built-In Side Burner is not in use. Check that the areas under the control panel and the slide out bottom tray are free from debris that might obstruct the fl ow of combustion or ventilation air. Operating WARNING: Only use this barbecue outdoors in a well-ventilated area. Do not use in a garage, building, breezeway or any other enclosed area. WARNING: Your Weber Built-In Side Burner shall not be used under an unprotected combustible roof or overhang. WARNING: Your Weber Built-In Side Burner is not intended to be installed in or on recreational vehicles and/or boats. WARNING: Do not use the barbecue within 24 inches of combustible materials, top, bottom, back or sides of the grill. WARNING: The entire cooking box gets hot when in use. Do not leave unattended. WARNING: Keep any electrical supply cord and the fuel supply hose away from any heated surface. WARNING: Keep the cooking area clear of flammable vapors and liquids, such as gasoline, alcohol, etc., and combustible materials. Gas Supply Testing Disconnect your Weber gas barbecue when the gas supply is being tested at high pressures. This appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kpa). Turn OFF your Weber gas barbecue when the gas supply is being tested at low pressures. This appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at the pressure equal to or less than 1/2 psig (3.5 kpa).

4 GAS INSTRUCTIONS LOCATING YOUR BUILT-IN SIDE BURNER When determining a suitable location for your Built-In Side Burner installation, give attention to concerns such as exposure to wind, proximity to traffi c paths, and keeping any gas supply lines as short as possible. Never locate the Summit Built-In Side Burner in a garage, breezeway, shed, under an unprotected overhang, or other enclosed area. Locate the Side Burner and structure so there is enough room to safely evacuate the area in case of a fi re. CLEARANCE FROM COMBUSTIBLE SURFACES OR STRUCTURES WARNING: Clearance from the outside walls of the sides and back of the LP Tank Cabinet must be a minimum of 24 inches any surface. Refer to Typical Gas Supply Installation before starting installation. WARNING: The structure, island counter tops and adjacent work areas for the LP Tank Cabinet installation must be built from noncombustible materials only. NOTE: If you have questions on what materials are considered noncombustible, contact you local building supplier or fi re department. Any Surface 24 inches 24 inches min. for lid clearance Side Burner 24 inches Any Surface 24 inches Note: For a countertop treatment: Recommended 3/4 inch overhang. Notch front edge for frame to fully slide in. Any Surface BUILT-IN SRUCTURE CUTOUT DIMENSIONS All dimensions are to finished surfaces. WARNING: All counter top finished surfaces must be constructed of a noncombustible material. Side Burner Cut out Dimensions Tolerances A " + 1 /4" - 1 /4" B 3 3 /4" + 1 /4" - 1 /4" C 16 1 /4" + 1 /4" - 1 /4" 4

5 GAS INSTRUCTIONS BUILT-IN GAS LINE LOCATIONS GENERAL CONSTRUCTION DETAILS Summit Built-In side burner unit should be on site before construction begins. All dimensions have a tolerance of plus or minus +/- 1 /4 inch. Provide access for a corrugated gas line depending on the location of the side burner in relation to your main gas supply and regulator position. Area should be kept clear of sharp, jagged, or extremely abrasive surfaces to avoid possible damage to gas supply lines. Exercise caution when pulling gas lines through built-in structure. A 3/8 inch stainless steel corrugated gas line should be used to connect the side burner to the regulator accessory coupling. WARNING: Do not use a rubber gas hose. Test connections All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of ANSI Z223.1/NFPA 54. DANGER Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for gas leaks. This will result in a fire or explosion which can cause serious bodily injury or death, and damage to property. Be sure to secure the side burner unit with non corrosive screws anchored into the fi nished surface of the island structure. Replace the plastic plug on the front mounting hole to conceal the screw once side burner is secure. 3/8" SAE stainless corregated gas line to regulated gas supply MOUNTING THE SIDE BURNER Connect the corrugated gas line to the side burner valve located on the back right hand side of side burner. 5

6 GAS INSTRUCTIONS TYPICAL NATURAL GAS SUPPLY INSTALLATION We recommend that this installation be done by a LICENSED professional. GENERAL SPECIFICATIONS FOR PIPING Note - Contact your local municipality for building codes regulating outdoor gas grill installations. In absence of Local Codes, you must conform to the latest edition of National Fuel Gas Code ANSI Z223.1/ NFPA54. This grill is designed to operate at 4.5 inches of water column pressure. A manual shut-off valve must be installed outdoors, and be accessible, not in the built-in structure. An additional manual shut-off valve indoors should be installed in the branch fuel line in an accessible location near the supply line. Caution: If young children are in the area, a locking valve should be considered. Pipe compound should be used which is resistant to the action of liquid propane gas when gas connections are made. The gas connections must be fi rmly attached to rigid, permanent construction. GAS LINE PIPING Refer to the piping chart at the bottom of previous page. The corrugated gas line from the manifold is 58 inches long. Do not extend the gas line. We have provided the means to make an SAE 45 fl are connection. Do not use pipe sealant on this connection. If the length of line required does not exceed 50 feet, use a 5/8 O.D. tube. One size larger should be used for lengths greater than 50 feet. Refer to piping chart. Gas piping may be copper tubing, type K or L; polyethylene plastic tube, with a minimum wall thickness of.062 inch; or standard weight (schedule 40) steel or wrought iron pipe. Copper tubing must be tin-lined if the gas contains more than 0.3 grams of hydrogen sulfi de per 100 cubic feet of gas. Plastic tubing is suitable only for outdoor, underground use. Gas piping in contact with earth, or any other material which may corrode the piping, must be protected against corrosion in an approved manner. Underground piping must have a minimum of 18 cover. Note: The information provided in this manual is general for typical installations. We cannot cover all possible installation ideas. We recommend, prior to installation, that you contact your municipality for local building codes and your local fire department for installation verification. If you have any questions, contact Customer Service at Table 10-1 Maximum Capacity of Pipe in Cubic Feet of Gas per Hour for Gas Pressures of 0.5 psi or Less and a Pressure Drop of 0.3 Inch Water Column. (Based on a 0.60 Specific Gravity Gas) Nominal Iron Pipe Size (Inches) Internal Diameter (Inches) 6 Length of Pipe (Feet) / / / / / / / National Fire Protection Association, Inc., and International Approval Services - U.S., Inc. All Rights Reserved.

7 GAS INSTRUCTIONS TEST CONNECTIONS All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54. DANGER Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for gas leaks. This will result in a fire or explosion which can cause serious bodily injury or death, and damage to property. REGULATOR The regulator should be adequately supported. The regulator must be installed close to the appliance. Each appliance must have a separate regulator. CONNECT GAS SUPPLY 1) Uncap the fl are fi tting from the optional side burner connection located at regulator. Note: You must connect your side burner to a Weber approved regulator(part number #62434) located at main gas supply. If you do not use a Weber approved regulator the Warranty on the Summit Built-In Side Burner will be voided. If you have any questions, contact Customer Service at ) Connect the corrugated gas line to the side burner Connection. top view Test connections All connections and joints must be thoroughly tested for leaks in accordance with local codes and all listed procedures in the latest edition of ANSI Z223.1/NFPA 54. DANGER Do not use an open flame to check for gas leaks. Be sure there are no sparks or open flames in the area while you check for gas leaks. This will result in a fire or explosion which can cause serious bodily injury or death, and damage to property. WARNING: You should check for gas leaks every time you disconnect and reconnect a gas fitting. Note - All factory-made connections have been thoroughly checked for gas leaks. As a safety precaution however, you should recheck all fi ttings for leaks before using your Summit Built-In side burner. Shipping and handling may loosen or damage a gas fi tting. You will need: a soap and water solution, and a rag or brush to apply it. Turn on gas supply. Check for leaks by wetting the connections with the soap and water solution and watching for bubbles. If bubbles form or if a bubble grows, there is a leak. Note - Since some leak test solutions, including soap and water, may be slightly corrosive, all connections should be rinsed with water after checking for leaks. WARNING: Do not ignite burners when leak checking. Cap (Optional Side Burner) Hard piped gas supply Regulator Figure 1 top view Hard piped gas supply to side burner Regulator Figure 2 7

8 GAS INSTRUCTIONS Check: 1) Corrugated gas line-to-accessory T Connection. 2) Main gas Supply to regulator WARNING: If there is a leak a connection(1), retighten the fitting with a wrench and recheck for leaks with soap and water solution. If a leak persists after retightening the fitting, turn OFF the gas. DO NOT OPERATE THE GRILL. Contact the Customer Service Representative in your region using the contact information sheet provided with your manual. Check: When leak checks are complete, turn gas supply OFF at the source and rinse connections with water. Side Burner Lighting Instructions DANGER Failure to open the lid while igniting the side burner, or not waiting 5 minutes to allow the gas to clear if the side burner does not light, may result in an explosive flame-up which can cause serious bodily injury or death. Lighting the side burner. 1) Open the side burner lid. 2) Check that the side burner valve is turned OFF. (Push the knob down and turn clockwise to ensure it is in the off position.). 3) Turn the gas supply valve on. 4) Push down and turn the side burner control valve to START/HI. 5) Push igniter button and hold until burner ignites. You will hear the igniter sparking. CAUTION: Side burner flame may be difficult to see on a bright sunny day. WARNING: If the side burner does not light: 1) Turn OFF the side burner control valve. 2) Wait 5 minutes to let the gas clear before you try again or try to light with a match. 8

9 OPERATING Manually Lighting the Side Burner DANGER Failure to open the lid while igniting the side burner, or not waiting 5 minutes to allow the gas to clear if the side burner does not light, may result in an explosive flame-up which can cause serious bodily injury or death. Replace Igniter Batteries Parts required: 1 AA alkaline battery per igniter. Unscrew igniter button from top of control panel. Remove igniter button and contact spring. Remove old battery and replace with a new AA alkaline battery. Positive end(1) of battery faces up as shown in illustration. Replace spring contact(2) and screw igniter button(3) back down. 1) Open the side burner lid. 2) Check that the side burner valve is turned OFF. (Push the knob down and turn clockwise to ensure that it is in the off position.). 3) Turn the gas supply valve on. 4) Put match in a match holder and strike match. 5) Push down and turn the side burner control valve to START/HI. 6) Hold match holder and lit match by right side of side burner. 7) Push igniter button and hold until burner ignites. You will hear the igniter sparking. CAUTION: Side burner flame may be difficult to see on a bright sunny day. WARNING: If the side burner does not light: 1) Turn OFF the side burner control valve. 2) Wait 5 minutes to let the gas clear before you try again or try to light with a match. To Extinguish Push down and turn each burner control knob clockwise to the OFF position. Turn gas supply OFF at the source. 9

10 SIDE BURNER TROUBLESHOOTING Problem Check Cure Side Burner does not light. Is gas supply off? Turn supply on. Flame is low in HIGH position. Is the fuel hose bent or kinked? Straighten gas line. Push button ignition does not work. Does burner light with a match? If match lights burner, check igniter (see below). If problems cannot be corrected by using these methods, please contact the Customer Service Representative in your region using the contact information sheet provided with your manual. Side Burner maintenance WARNING: All gas controls and supply valves should be in the OFF position. 1) Igniter Wire 2) Burner 3) 1/8 to 3/16 inch gap between electrode and burner (3) Make sure wire is connected between the igniter and electrode. Adjust igniter electrode to burner. Gap should be 1/8 to 3/16 inch from tip of electrode to burner. Spark should be a white/blue color, not yellow. Side Burner Grate Side Burner Cap Side Burner Ring & Head Igniter Electrode Control Knob Igniter 10

SUMMITTM 400 & 600. Natural Gas Barbecues. Step-By-Step Guide

SUMMITTM 400 & 600. Natural Gas Barbecues. Step-By-Step Guide SUMMITTM 400 & 600 Natural Gas Barbecues Step-By-Step Guide W E B E R W E B E R W E B E R W E B E R Summit 400 NG Summit 600 NG CANADIAN GAS ASSOCIATION R A P P R O V E D WARNING: Follow all leak check