Adhesion Performance Requirements for Adhesive Backed Light Trim and Foam. Technical Bulletin August, 2016

Transcription

1 GMW Type 1 Adhesion Performance Requirements for Backed Light Trim and Foam Automotive Spec Testing Technical Bulletin August, M tested the following adhesive tapes to the Automotive OEM Spec: GMW Type 1 Adhesion Performance Requirements for Backed Light Trim and Foam. The results of the testing are provided in the following information. s not listed on this document have not been tested to this spec. 3M Reinforced Transfer Tape L1+RT (3.2 mil) 3M Double Coated Polyester Tape L1+DCP (3.5 mil) 3M Double Coated Polyester Tape L2+DCP (4.8 mil) 3M Transfer Tape L2+T5 (5.0 mil) 3M Transfer Tape L3+T5 (5.0 mil) Test 180º Peel Adhesion on 300mm / 12 in per min Test Condition / Environment As Received - 24 hour Room Temp Humidity GMW ºC / 104ºF + 100% RH Cycle Exposure GMW14124 cycle M (not required for type I) 1

2 PU Ester PU Ether XLPE Foam EPDM Foam Nitrile Foam Neoprene Foam EPDM Rubber Neoprene Rubber Santoprene Rubber Butyl Rubber GMW Type 1: Adhesion Performance Requirements for Backed Light L1 + RT L1 + DCP L2 + DCP L2 + T5 L3 + T5 As received F F P F N/A N/A N/A N/A N/A N/A N/A Heat Age P P P F N/A N/A N/A N/A N/A N/A N/A Humidity P F P F N/A N/A N/A N/A N/A N/A N/A Cycle P P P F N/A N/A N/A N/A N/A N/A N/A As Received P P P P N/A N/A N/A N/A N/A N/A N/A Heat Age P P P F N/A N/A N/A N/A N/A N/A N/A Humidity F F P F N/A N/A N/A N/A N/A N/A N/A Cycle P F P F N/A N/A N/A N/A N/A N/A N/A As Received P P P P P P P N/A N/A N/A N/A Heat Age P P P P P F P N/A N/A N/A N/A Humidity P P P P P F F N/A N/A N/A N/A Cycle P P P F P F F N/A N/A N/A N/A As Received P P P P P P P N/A N/A N/A N/A Heat Aged P P P P P F P N/A N/A N/A N/A Humidity P P P P P P P N/A N/A N/A N/A Cycle P P P P P F P N/A N/A N/A N/A As Received Heat Aged P P P P P P P P P P P P P P P P P P F P P F Humidity P P P P P P P F P P F Cycle P P P P P P P F F F F P = Pass, F = Fail, N/A = Not Tested 2

3 GMW Type 1: Adhesion Performance Requirements for Backed Light L1 + RT As Received - 24 hour Room Temp / or L1+RT Clean Peel Fail PU Ether Foam Clean Peel Fail XLPE Foam Foam Tear Pass % Cohesive Fail L1+RT / or Clean Peel Pass PU Ether Foam Clean Peel Pass XLPE Foam Foam Tear Pass Clean Peel Fail L1+RT Humidity GMW ºC / 104ºF + 100% RH / or Clean Peel Pass PU Ether Foam Clean Peel Fail XLPE Foam Foam Tear Pass Clean Peel Fail L1+RT Cycle Exposure GMW Cycle M (not required for type I) / or Clean Peel Pass PU Ether Foam Clean Peel Pass XLPE Foam Foam Tear Pass Cohesive Fail 3

4 GMW Type 1: Adhesion Performance Requirements for Backed Light L1 + DCP L1+DCP As Received 24 hour Room Temp / or Clean Peel Pass PU Ether Foam Clean Peel Pass XLPE Foam Foam Tear Pass Clean Peel Pass L1+DCP / or Clean Peel Pass PU Ether Foam Clean Peel Pass XLPE Foam Foam Tear Pass Clean Peel Fail L1+DCP Humidity GMW ºC / 104ºF + 100% RH / or Clean Peel Fail PU Ether Foam Clean Peel Fail XLPE Foam Foam Tear Pass Clean Peel Fail L1+DCP Cycle Exposure GMW Cycle M (not required for type I) / or Clean Peel Pass PU Ether Foam Clean Peel Fail XLPE Foam Foam Tear Pass Clean Peel Fail 4

5 GMW Type 1: Adhesion Performance Requirements for Backed Light L2 + DCP L2+DCP As Received 24 hour Room Temp / or Clean Peel Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Cohesive Pass Neoprene Foam Clean Peel Pass L2+DCP / or Clean Peel Pass PU Ether Foam Clean Peel Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Clean Peel Fail Neoprene Foam Clean Peel Pass L2+DCP Humidity GMW ºC / 104ºF + 100% RH / or Clean Peel Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Cohesive Fail Neoprene Foam Cohesive Fail 5

6 GMW Type 1: Adhesion Performance Requirements for Backed Light L2 + DCP (Cont.) L2+DCP Cycle Exposure GMW Cycle M (not required for type I) / or Clean Peel Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Clean Peel Fail EPDM Foam Foam Tear Pass Nitrile Foam Cohesive Fail Neoprene Foam Cohesive Fail L2 + T5 L2+T As Received 24 hour Room Temp / or Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Clean Peel Pass EPDM Foam Foam Tear Pass Nitrile Foam Foam Tear Pass Neoprene Foam Foam Tear Pass L2+T5 Avg Peel / or Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Clean Peel Fail Neoprene Foam Foam Tear Pass L2 + T5 (Cont.) 6

7 GMW Type 1: Adhesion Performance Requirements for Backed Light L2+T Humidity GMW ºC / 104ºF + 100% RH / or Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Clean Peel Pass Neoprene Foam Clean Peel Pass L2+T Cycle Exposure GMW Cycle M (not required for type I) / or Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Clean Peel Fail Neoprene Foam Clean Peel Pass 7

8 GMW Type 1: Adhesion Performance Requirements for Backed Light L3 + T5 L3+T As Received 24 hour Room Temp Observation Requirement 525 or or foam tear Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Clean Peel Pass EPDM Foam Foam Tear Pass NitrileFoam Clean Peel Pass Neoprene Foam Foam Tear Pass EPDM Rubber Clean Peel Fail Neoprene Rubber Clean Peel Pass Santoprene Clean Peel Pass Rubber Butyl Rubber Clean Peel Pass L3+T5 Observation Requirement 525 / or foam tear Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Clean Peel Pass Neoprene Foam Foam Tear Pass EPDM Rubber Clean Peel Fail Neoprene Rubber Clean Peel Pass Santoprene Clean Peel Pass Rubber Butyl Rubber Clean Peel Fail 8

9 GMW Type 1: Adhesion Performance Requirements for Backed Light L3 + T5 (Cont.) L3+T Humidity GMW ºC / 104ºF + 100% RH / or Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Foam Tear Pass Neoprene Foam Foam Tear Pass EPDM Rubber Cohesive Fail Neoprene Rubber Clean Peel Pass Santoprene Clean Peel Pass Rubber Butyl Rubber Clean Peel Fail L3+T Cycle Exposure GMW Cycle M (not required for type I) / or Foam Tear Pass PU Ether Foam Foam Tear Pass XLPE Foam Foam Tear Pass Foam Tear Pass EPDM Foam Foam Tear Pass Nitrile Foam Clean Peel Pass Neoprene Foam Clean Peel Pass EPDM Rubber Clean Peel Fail Neoprene Rubber Clean Peel Fail Santoprene Clean Peel Fail Rubber Butyl Rubber Clean Peel Fail 9

10 GMW Type 1: Adhesion Performance Requirements for Backed Light Technical Information The technical information, recommendations and other statements contained in this document are based upon tests or experience that 3M believes are reliable, but the accuracy or completeness of such information is not guaranteed. Product Use Many factors beyond 3M s control and uniquely within user s knowledge and control can affect the use and performance of a 3M product in a particular application. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user s method of application. Warranty, Limited Remedy, and Disclaimer Unless an additional warranty is specifically stated on the applicable 3M product packaging or product literature, 3M warrants that each 3M product meets the applicable 3M product specification at the time 3M ships the product. 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. If the 3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M s option, replacement of the 3M product or refund of the purchase price. Limitation of Liability Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence o r strict liability. ISO 9001:2000 This Industrial s and Tapes Division product was manufactured under a 3M quality syst em registered to ISO 9001: 2000 standards. Industrial s and Tapes Division Converter Markets 3M Center, Building 225-3S-06 St. Paul, MN (Fax) 3M is a trademark of 3M Company. Santoprene is a trademark owned by Exxon Mobil Corporation. 3M 2016 E (08/16) 10