Hydrotherapy Jets System for a Fiberglass Pool
|
|
- Tracey Washington
- 5 years ago
- Views:
Transcription
1 Page 1 of 5 Parts List 1-50 Flex PVC pipe / 2 " Ball Valves 4-1/2" 90 degree elbows 4 - Lengths of 1/2" PVC 4 - Jet bodies 4 - Jet nozzles 6 - Female slip/female slip unions 2 - Female slip/fpt union 6 - Male slip/ Female slip elbows 8 - Female slip/female slip elbows 2 - Suction fitting assemblies 1 - Jet tool / 2 " Tees 2 - Female slip couplers / 2 " hole saw w/ 1/4" drill bit 4 - MPT/Male slip adapter 1-4oz Can of PVC Cement 1-4oz Can of PVC Cleaner / 2 " Male slip plugs 2 - #10 Wing nut plugs 4 - #11 Wing nut plugs 4 - Clear Gaskets 1-3/4 HP Circulating Centrifugal Pump Placement Considerations Determine your desired location for the four hydrotherapy jets. Typically jets are placed on the rear wall of the pool just above the seat. The jets can be either clustered together or located remotely from one another. Because personal preference will vary, a good way to select location is to sit in a chair and measure from the seating surface to where the jet would be most comfortable on your back. This will give you the vertical distance from the base of the bench to the desired jet location. If the jets are to be vertically aligned, the distance from center point to center point must be a minimum of 10. The top jet has to be a minimum of 11 from the top of the pool. The two jet suctions need to be 3 apart (from center point to center point). We have provided a diagram for placing the suction holes at the front of the pool with the rest of your equipment. The 3/4hp, 220v jet pump needs to be installed in the cavity created for the Water Quality System at the front of the pool, since it will receive its electrical supply from the heater controller. The electrical cord, which is pre-wired to the pump, plugs into port P1 (orange) on the heater controller. Please remember that drainage for the Water Quality System cavity is required. Important notice: If your pool or equipment will be subjected to freezing temperatures, special consideration must be given to the jet system in order to avoid freezing of the plumbing lines. Your heater/controller is programmed to automatically circulate the jet plumbing lines four times a day. This circulation reduces the likelihood that the plumbing lines will freeze. Once your pool s installation is complete and the pool is in an enclosed space, additional insulation of the siding material will help keep the warm air radiating from your pool in the enclosed space, which is where both your jet pump and jet plumbing lines are located. Having your jet plumbing line run within the space immediately adjacent of the pool is necessary for proper protection from freezing. Additionally, the heater controller comes equipped with a smart winter mode (SWM). When the SWM is enabled, the system will automatically turn the pump on to ensure that there is warm water moving through the plumbing lines. Please see the Water Quality for more information on this feature. If you believe that these measures will be insufficient to prevent your jet plumbing lines from freezing, please call our Customer Service Department.
2 Page 2 of 5 Installation Instructions 1. With the 2 1 / 2 " hole saw provided, drill four holes through the pool wall in the predetermined locations. After the holes have been drilled, sand or grind the backside of the pool flat, and apply a small amount of silicone to the exposed edge of the hole. Again, the placement of the two suction holes need to be considered. They have to be 3 apart (from center point to center point), a minimum of 12 up from the floor of the pool, and a minimum of 12 away from the corner. These suction fittings should be placed at the front of the pool. 2. Install each thru-wall fitting so that there is a rubber gasket between the fitting and the inside of the pool wall. The second rubber gasket will not be used in this application. The cork gasket will be used on the backside of the pool wall. Make sure to use silicone sealant on both sides of the pool wall. 3. Remove the protective strainer from the suction fitting. Add Teflon sealant onto the thread of each and attach a female slip x female pipe thread union onto each adapter. Next glue a male slip x female slip 90º elbow into each union so that they are facing each other. These two suction lines need to be connected before the suction line goes back to the pump. Ideally, the tee should be centered between the two suction fittings. Once the jet suction fittings are installed, the fitting can be plugged from inside the pool with a #10 wing nut plug until all of the jet plumbing is complete. 4. Cut lengths of the 1/2" PVC pipe for the air supply to each jet. The air pipes for the lower jets may require elbows to clear the jets and piping above. Once installed, the open top of the air supply must be above the water line to prevent spill over. The pipe should be terminated 1/4" below the top flange of the pool. The 1/2" air supply tubes should be cemented to the jet bodies first, in an inverted position, with the jet internals removed, to prevent dripping of PVC cement or cleaner into the air passages. If you intend to install your pool fully in-ground, then the 1/2 air pipe installation will not be appropriate. Instead, glue the plug into the 1/2 opening in the top of the jet body. Then connect the 1 1 / 2 air openings with 1 1 / 2 pipe and run this one large air-line back to the front of the pool so that it terminates in the cavity that was created for your water quality system. Make sure that the end of this air pipe is positioned above the water line in the pool. 5. For your four jet fittings, place the white gasket between the bulkhead fitting and the pool wall. The clear gasket provided will not be used in this application. Apply a bead of silicone sealant on the backside of the pool wall around the perimeter of the hole where contact will be made with the face of the jet body (The portion of the jet fitting that receives the plumbing). Press the jet body with air tube installed against the pool wall, aligning with the drilled hole. 6. Apply Teflon sealant completely around the threaded barrel of the jet bulkhead. Screw the jet bulkhead with the gasket and Teflon into the corresponding jet body. Repeat this procedure for each of the three remaining jets. A jet tool has been included in your kit to help with the tightening of the jet bulkheads. Note: Be sure not to cross-thread the jet bulkhead as it will not seat properly. 7. Cut lengths of the 1 1 / 2 " PVC pipe provided to connect to each of the four jets. Three 1 1 / 2 " tees and one elbow should be fabricated to provide a supply piping manifold to coincide with the four jet locations. From each of these four fittings extends 1 1 / 2 " PVC to a union. From the unions, connect to each jet with 1 1 / 2 " PVC and an elbow (lower jets use male slip-female slip street elbows, upper jets use a nipple cut to length and a female slip-female slip elbow). The side of each jet opposite where the supply is connected at the bottom will require a plug. The unions allow each jet to be installed separately either before or after the supply piping manifold is assembled. 8. Cement all PVC slip connections following the cement manufacturer's recommendations. 9. Check the 1/2" air supply pipes to make certain that all four are 1/4 below the top flange of the pool wall. Extend or cut these tubes as required. 10. With the four jets and the suction fittings installed, the ball valves and remaining piping back to the jet pump can be installed. Union fittings have been provided on each side of the jet pump to facilitate its removal should service ever be required. The pump will come with the electrical cord pre-wired. The pump should be placed into the Water Quality System cavity close enough to the heater controller so that it can be plugged in. The clearance behind finish skirting should be considered when plumbing the jet pump.
3 Page 3 of The jets can be turned on by pressing the pump button on the keypad once then, press it a second time to turn off the jets. Before operating the hydrotherapy jets, make certain that both ball valves are open and the threaded plug in the suction fitting has been removed. The protective suction strainer should now be reinstalled at this time. It is extremely important that strainer be screwed into the suction fitting assembly.
4 Page 4 of 5
5 Page 5 of 5
Parts List. Description. Additional Considerations. Installation Instructions. Dual/Elite Hydraulic Treadmill Kit (supplied by EPI)
Page 1 of 9 Parts List Dual/Elite Hydraulic Treadmill Kit (supplied by EPI) Qty Description Treadmill Body 1 Treadmill Power Unit (per Treadmill Body) 2 Treadmill Decks (per Treadmill Body) 1 Treadmill
More informationFOR INSTALLING CO 2 BLENDER KIT (P/N IN BEER SYSTEM
IMI CORNELIUS INC One Cornelius Place Anoka, MN 55303-623 Telephone (800) 238-3600 Facsimile (612) 22-326 INSTALLATION INSTRUCTIONS FOR INSTALLING CO 2 BLENDER KIT (P/N 111612000 IN BEER SYSTEM SECONDARY
More informationSanitizer Parts. Sanitizer Parts. Replacement Parts for Sanitizers
Sanitizer Parts for Sanitizers 513 Automatic Feeder Model 300, 302, 300-19, 300-29 Order No.: R171016 R171026 Model No.: 300 302 Description: AUTOMATIC FEEDER SPA HOT TUB FEEDER 1 1 R172008W 3 in. threaded
More informationFITTINGS THREAD LUBRICANTS. Fittings 20,000 PSI
Jetstream offers a wide variety of fittings with various connection types to fit your 20,000 psi application needs. The standard connection types, Type M, MP, and MP Tube lance, are available in standard
More informationVOLUMATIC WATER REGULATOR
Introduction The Chore-Time VOLUMATIC regulator is designed to regulate water pressure for Chore-Time Layer and Brood Grow Nipple Watering Systems. There is a model for manual adjustment of the regulator
More informationCOUNTER CURRENT UNIT. Instruction Manual
COUNTER CURRENT UNIT Instruction Manual 1 Introduction: Congratulations on your purchase of a new Certikin counter current swimming unit. This unit has been developed and built by qualified personnel especially
More informationFiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual
Fiber Optic Lighted Bubbler Spillway Pot (DLP-45) Installation Manual 27.75 23.75 25.50 20.75 Specifications: 8-13 GPM 100 strand fiber - Bubbler 75 strand fiber - Spillway Light Bar 45 ft. fiber tail
More informationRain Barrel Set Up. Supplies: Most supplies are available at your local hardware stores.
Rain Barrel Set Up Supplies: Most supplies are available at your local hardware stores. Two 55 gallon food grade drums with bungs (available locally from All Valley New & Used 360 854 2006 & Skagit Farmers
More informationBlue Points 1 ¼ WELL POINT INSTALLATION INSTRUCTIONS
Blue Points 1 ¼ WELL POINT INSTALLATION INSTRUCTIONS This brochure is designed to provide step-by-step instructional assistance to the individual who wishes to install a shallow water well system for residential
More informationSPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.
2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or
More informationHow Do I Install My Garden Master Bucket Garden?
How Do I Install My Garden Master Bucket Garden? 1. On the arrival of your Bucket Garden open the bucket and remove the 4 screws from the outside of the bucket rim and pull the 2 buckets apart. Check the
More informationPressure Dump Valve Service Kit for Series 3000 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator
More informationBlue River Technologies Port-A-Poly Mixer w/2.5 GPH LMI Pump And Secondary Water Dilution Line INSTALLATION AND OPERATION
Blue River Technologies Port-A-Poly Mixer w/2.5 GPH LMI Pump And Secondary Water Dilution Line INSTALLATION AND OPERATION Install your Blue River Technologies Port-A-Poly mixing system in a clean dry area.
More informationPoolNaturally. Pure. Simple. Genius. Installation and Product Use Instructions In ground and above ground pools
PoolNaturally Pure. Simple. Genius. Installation and Product Use Instructions In ground and above ground pools V2.31 Installation Diagrams: (Installation can be done either before or after the pump. Shown
More informationBelow are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project.
Greg Cowens' $10 PVC Roller Reefing for CP-16's by Greg Cowen Below are the instructions to build a roller-furling unit for under $10. Read the entire process before beginning the project. Materials: 2
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationINSTALLATION & START-UP INSTRUCTIONS. Clack WS1 & WS1.25 METER WATER SOFTENER SYSTEMS
INSTALLATION & START-UP INSTRUCTIONS Clack WS1 & WS1.25 METER WATER SOFTENER SYSTEMS 1999-2009 QualityWaterForLess.com - 1 - info@qualitywaterforless.com Preface: Thank you for your purchase of a new Water
More informationVessel Installation and Operating Manual
For In-ground and Aboveground Pools Vessel Installation and Operating Manual Important Safety Information Please read this manual prior to installation. Nature 2 Express is designed to sanitize in-ground
More informationHow to Make a Unique Industrial-Looking PVC Lamp
How to Make a Unique Industrial-Looking PVC Lamp copyright 2014 by Brooks Owen Owen Publications Battle Ground, WA 98604-0305 USA ALL RIGHTS RESERVED No part of this publication may be reproduced or transmitted
More informationVOLUMATIC WATER REGULATOR
VOLUMATIC WATER REGULATOR For Cage Systems - PDS and Manual Adjustment Part Number 00-, 00-, 00- Introduction The Chore-Time VOLUMATIC Water Regulator is designed to regulate the water pressure for the
More informationInstallation Manual. Model # SF-3W 9/16/03 REV 1. Arch Chemicals, Inc Lower River Road. P.O. Box 800 Charleston, TN PULSAR
Installation Manual Model # SF-3W Arch Chemicals, Inc. 1200 Lower River Road. P.O. Box 800 Charleston, TN 37310-0800 1-800-4-PULSAR 9/16/03 REV 1 Product Stewardship MAKING THE WORLD A BETTER PLACE Arch
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
Warrior D.E. Filter Operating Procedures IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION I. FILTER INSTALLATION... 1 SECTION II. FILTER
More informationSEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
More informationInstallation and Operating Manual
Safety Instructions Important Information Please read prior to installation ATTENTION! ELECTRICAL HAZARD FOR INGROUND POOLS AND ABOVEGROUND POOLS Installation and Operating Manual IMPORTANT Pool Owner,
More informationCrystal Spring Feeder Protocols
Crystal Spring Feeder Protocols Installation Instructions Starting Weaned Pigs Management Instructions Gro Master 402.493.4550 3838 North 108th Omaha, NE 68164 Crystal Spring Feeder Protocols Installation
More informationROUND ASSEMBLY. Positioning
ROUND ASSEMBLY Positioning To ensure maximum enjoyment and efficiency, consider the following steps when selecting the desired location of you pool. Select a location that receives maximum sunlight for
More informationInstallation Guide For Spillways & LED Light Bars
Installation Guide For Spillways & LED Light Bars *A pdf copy can be obtained via www.iearth.com.au/downloads 1 TABLE OF CONTENTS A1. Size Availability.. Page 3 B1. Type of Spillway Effects. Page 3 1.
More informationWritten By: Dozuki System
KidWash 2 : PVC Sprinkler Water Toy Written By: Dozuki System 2017 www.botsbits.org Page 1 of 8 INTRODUCTION Fun toy with mister jets helps kids beat the heat. This project owes a big debt to the original
More informationNOTICE WARNING MDX-R3 FOR FIBERGLASS POOLS OWNER S MANUAL AND INSTALLATION GUIDE SUBMERGED SUCTION OUTLET FOR MULTIPLE DRAIN USE FOR USE ON FLOOR
MDX-R3 FOR FIBERGLASS POOLS OWNER S MANUAL AND INSTALLATION GUIDE SUBMERGED SUCTION OUTLET FOR MULTIPLE DRAIN USE FOR USE ON FLOOR SEE SPECIAL INSTRUCTIONS FOR CALIFORNIA ON PAGE 1 Safety compliant according
More informationETL listed for installations within 5 ft. (1.5M) of outer edge of water
Color Light Streams Lighted Super Bubbler Kit Gunite CLSSBK SAVE THESE INSTRUCTIONS! SR Smith Color Light Streams Lighted Super Bubbler is a very simple device to provide lighted water for small fountains
More information1. Product Name. 2. Product Code. 3. Colour. 4. Brief Description. 5. Contents. Snoezelen Sensory Corner Kit. Cream Cushioned Platform
1. Product Name Snoezelen Sensory Corner Kit 2. Product Code 22517 3. Colour Cream Cushioned Platform 4. Brief Description Transform a corner of a room into an interactive Snoezelen Multi-Sensory Environment
More informationRetractable Security Cover for a Swim Spa
Parts List Retractable Security Cover Kit 3" PVC pipe Leading edge Cover Track (pre-attached to Swim Spa) Optional cover pump (for outdoor installations) Rocky Roller Kit 2 Roller A-Frame Brackets 1/2"
More informationTechnical Bulletin. Parts and Service News. LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6
Equipment Affected Technical Bulletin LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6 Ford 4.2L V-6 powered tractors with LPG fuel systems. Part Description Discrepancy Fuel Pressure Lock-off
More informationRAINBOW CHLORINE/BROMINE FEEDER MODEL #320
RAINBOW CHLORINE/BROMINE FEEDER MODEL #320 Features: No special venting required. Completely enclosed-no escaping gases. Positive external no-clog control valve. When used with timer, feeder is designed
More informationOperating Instructions Models and Hydrostatic Test Pumps
Operating Instructions Models 33100 and 33101 Hydrostatic Test Pumps 33100 DIMENSIONS: WEIGHT: PUMP: MOTOR: CONTROL: GAUGE: DISCHARGE HOSE: 16 (40cm) L x 22 (55cm) W x 18 (45cm) H 87 lbs., 39.5 kg Triplex
More informationAFL Industries, 1101 West 13 th St, Riviera Beach, FL 33404 PHONE: (561) 848-1826 FAX: (561) 848-9454 E-Mail: Sales@aflindustries.com AFL-STD MODEL OSV-4 SS INSTALLATION, OPERATION & MAINTENANCE BROCHURE
More informationInstallation of Your SprayMaster System
Installation of Your SprayMaster System 1. At the installation site, remove all equipment from the corrugated box and the polyethylene drum and replace the drum lid. Check the picture to identify each
More informationModel VR6 System. Installation, Operation & Maintenance
Model VR6 System Installation, Operation & Maintenance General: All Archer Instruments chlorination systems are carefully designed and tested for years of safe, accurate field service. All Archer Instruments
More informationInstallation/Care/Use Manual
Installation/Care/Use Manual EMASM Surface Mount Bottle Filling Station IMPORTANT THIS IS AN INDOOR APPLICATION ONLY! ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSONNEL. TOOLS/ITEMS REQUIRED
More informationP5/8/08 Page 1 of 26 FASTLANE POOL TM OWNER S MANUAL
P5/8/08 Page 1 of 26 FASTLANE POOL TM OWNER S MANUAL P5/8/08 Page 2 of 26 RECEIVING YOUR FASTLANE POOL Your Fastlane Pool is shipped by common carrier and contains the following 13 packages: 1. (8) Top
More informationSingle and Triple Rain Barrel Setup
Single and Triple Rain Barrel Setup Introduction The following guide will enable you to prepare a rainwater collection system where there is an already established downspout. The construction is intended
More informationSKIMMER FOR VINYL & FIBERGLASS POOLS OWNER S MANUAL AND INSTALLATION GUIDE
SKIMMER FOR VINYL & FIBERGLASS POOLS OWNER S MANUAL AND INSTALLATION GUIDE NOTICE WARNING To Installers: Read and follow these instructions. Give these instructions to the facility owner to keep for future
More informationInstallation and Use Manual
Installation and Use Manual EMASMB & LMASMB Surface Mount Bottle Filling Stations Model EMASMB IMPORTANT THIS IS AN INDOOR APPLICATION ONLY! ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSONNEL.
More informationLAZY RIVER 3 3 PUMP LOCATION
.0 1 TEE WITH () " RETURN NOZZLE 1 1.0 10" OR 1 SCH 0 PVC PIPE RETURN WITH ACCELERATOR NOZZLE 2 LAZY RIVER PUMP LOCATION PUMP LOCATION PRELIMINARY SITE LAYOUT AND PUMP LOCATION 1 DETERMINE CURRENT RETURN
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
Clean & Clear Plus Cartridge Filters Owner's Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION I. FILTER INSTALLATION... 1 SECTION
More informationInstruction Manual Updated 7/26/2011 Ver. 2.2
4-Unit Model MB HTHP Filter Press #171-50-4: 115-Volt #171-51-4: 230-Volt Instruction Manual Updated 7/26/2011 Ver. 2.2 OFI Testing Equipment, Inc. 11302 Steeplecrest Dr. Houston, Texas 77065 U.S.A. Tele:
More informationSKIMMER FOR VINYL & FIBERGLASS POOLS OWNER S MANUAL AND INSTALLATION GUIDE
SKIMMER FOR VINYL & FIBERGLASS POOLS OWNER S MANUAL AND INSTALLATION GUIDE NOTICE WARNING To Installers: Read and follow these instructions. Give these instructions to the facility owner to keep for future
More informationINSTALLATION, CARE & USE MANUAL. EMASMB & LMASMB Surface Mount Bottle Filling Stations
INSTALLATION, CARE & USE MANUAL EMASMB & LMASMB Surface Mount Bottle Filling Stations IMPORTANT THIS IS AN INDOOR APPLICATION ONLY! ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSONNEL. TOOLS/ITEMS
More informationCO2 Tank Conversion Kit P.N , P.N , and P.N
Foodservice Group Multiplex Beverage Equipment Installation Instructions for CO2 Tank Conversion Kit P.N. 002247, P.N. 0022505, and P.N. 0025099 Introduction The following instructions cover the installation
More informationMIDDLESEX COUNTY COLLEGE EDISON, NJ LOCAL SUPPLIER BLANKET ORDER SPECIFICATIONS
MIDDLESEX COUNTY COLLEGE EDISON, NJ 08818 LOCAL SUPPLIER BLANKET ORDER SPECIFICATIONS The College is soliciting bids to award a Local Supplier Blanket Order agreement for the purchase of supplies for the
More informationHalsey Taylor Owners Manual 4410 Freeze Resistant Tubular Fountain STOP!
Halsey Taylor Owners Manual 4410 Freeze Resistant Tubular Fountain STOP! PLEASE READ THE FOLLOWING INFORMATION. ITALLATION ITRUCTIO FOR THE 4410FR FTN. WITH 97243C SINGLE VALVE CONTROL ASSEMBLY ARE LOCATED
More informationPipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
More informationQuality Plastic Pipe Fittings. Technical Data. Fabricated PVC Fittings IPS Class 100, 125, 160, 200 SCH 40 & SCH 80 Solvent Weld & Gasketed
Quality Plastic Pipe Fittings Technical Data Fabricated PVC Fittings IPS Class 100, 125, 160, 200 SCH 40 & SCH 80 Solvent Weld & Gasketed Effective April 1, 2002 PIPE DIMENSIONS IPS-IRON PIPE SIZE Minimum
More informationMIDDLESEX COUNTY COLLEGE EDISON, NJ LOCAL SUPPLIER BLANKET ORDER SPECIFICATIONS
MIDDLESEX COUNTY COLLEGE EDISON, NJ 08818 LOCAL SUPPLIER BLANKET ORDER SPECIFICATIONS The College is soliciting bids to award a Local Supplier Blanket Order agreement for the purchase of supplies for the
More informationSIMPLAIR PIPING TOOL. JXT Company
SIMPLAIR PIPING INGERSOLL-RAND SIMPLAIR PIPING With push-in fittings and lightweight anodized aluminum pipe, a SimplAir system provides ideal connection throughout your entire air distribution system.
More information2016 /17 Catalog. distributed exclusively throughout the U.S by
BALL VALVES/SEACOCKS Ball Valve ½ NPS 90659 2211 Ball Valve ¾ NPS 90660 2228 Ball Valve 1 NPS 90661 2235 Ball Valve 1¼ NPS 90662* 2242 Ball Valve 1½ NPS 90663 2259 Ball Valve 2 NPS 90664 2266 THRU-HULL
More informationBig Ride ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * *
Big Ride ASSEMBLY AND INSTALLATION INSTRUCTIONS * * C A U T I O N * * S.R. SMITH BIG RIDE SLIDES ARE MANUFACTURED FOR INSTALLATION AND USE ON INGROUND SWIMMING POOLS ONLY. THE BIG RIDE IS NEVER TO BE INSTALLED
More informationCLEAN AND CLEAR PLUS CARTRIDGE FILTER
CLEAN AND CLEAR PLUS CARTRIDGE FILTER INSTALLATION AND USER S GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Pressurized air can cause the lid to separate
More informationY:\Machine Manuals & Spare Parts Lists\PARTS BREAKDOWN\Commercial CW Gas\HD850WS Page 1
1.0 PIECE PARTS - parts listing 1 5311-0710 Nut 1 2 5443-2820 Hose Stem 1 3 6362-3950 O-Ring Seal 14.0x1.78 1 4 6414-2820 Strainer 1 5 6313-0030 Spring 2 6 5321-1980 Handhold 1 7 5066-2120 Cover 1 8 5363-1350
More informationInstallation Instructions
Installation Instructions COLONY SOFT 7.0 Centerset Lavatory Faucet 7.0 with Speed Connect Drain Congratulations on purchasing your American Standard faucet with the Speed Connect drain, a features found
More informationSanitizers. Sanitizers. Sanitizers for Pools & Spas
for Pools & Spas 207 IntelliChlor Salt Chlorinator Featured Highlights IntelliChlor Salt Chlorinator IntelliChlor Salt Chlorinator uses common table salt to produce all the chlorine a pool needs, safely,
More informationLEAK TROUBLESHOOTING
LEAK TROUBLESHOOTING If you suspect that your TMC isolation system is leaking (most often evidenced by going through air/nitrogen tanks too quickly), this guide will help you to find and fix the problem.
More informationW A S T E W A T E R T R E A T M E N T S Y S T E M S
W A S T E W A T E R T R E A T M E N T S Y S T E M S PROCEDURES FOR ASSEMBLY AND INSTALLATION A Division of Consolidated Trmt Systems, Inc. 1501 Commerce Center Drive Franklin, OH 45005 Tel: 937-746-2727
More informationDual Solenoid Gas Valve Installation
Installation IMPORTANT: These instructions are intended as a guide for qualified personnel installing or servicing FLYNN Gas Products. Carefully follow all instructions in this bulletin and all instructions
More informationInstallation Instructions
Installation Instructions Splashdown Fountain The Splash Down telescoping fountainhead comes in two sizes: the SD22 for use in water depths from 6 to 24 inches and the SD44 for use in water depths of 25
More informationINSTALLATION and OPERATION INSTRUCTIONS
INSTALLATION and OPERATION INSTRUCTIONS FLOJET Beer Pump Panels MODEL NO. 66134-1 66134-2 66134-3 66134-4 IMPORTANT INFORMATION This manual has been prepared to assist you in the operation of Perlick Beer
More information2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL
2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL Model: 52024 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement,
More informationBRILLIANT WONDERS LED BUBBLERS INSTALLATION INSTRUCTIONS & PRODUCT MANUAL CMP SERIES
BRILLIANT WONDERS LED BUBBLERS INSTALLATION INSTRUCTIONS & PRODUCT MANUAL CMP 25503 SERIES TABLE OF CONTENTS A. PRODUCT OVERVIEW A.1 SPECIFICATIONS A. PRODUCT OVERVIEW... 3 A.1 Specifications A.2 Packing
More informationSanitizers. Sanitizers. Sanitizers for Pools & Spas
Sanitizers Sanitizers for Pools & Spas 213 213 IntelliChlor Salt Chlorinator Featured Highlights IntelliChlor Salt Chlorinator IntelliChlor Salt Chlorinator uses common table salt to produce all the chlorine
More informationOperating Procedure TITON SUBSEA BOLT TENSIONER
Operating Procedure TITON SUBSEA BOLT TENSIONER B & A Hydraulics Ltd Block 1, Units 1 & 2 Souter Head Industrial Centre Souter Head Road Altens Aberdeen Phone: 01224 898955 Fax: 01224 898787 E-Mail: TITON@bahyd.co.uk
More informationAir Intake Snorkel Kit
SSV KIT - Air Intake Snorkel Kit Part number (SKU) : 715003733 Product: Side-by-side Project no: 487802499 Instruction Sheet P/N: 487802499 Revision no: Revision date: Item covered: Air Intake Snorkel
More informationHalsey Taylor Owners Manual STOP!
Halsey Taylor Owners Manual 4710 Freeze Resistant Floor Mounted Steel Fountain STOP! PLEASE READ THE FOLLOWING INFORMATION. ITALLATION ITRUCTIO FOR THE 4710FR FTN. WITH 97243C SINGLE VALVE CONTROL ASSEMBLY
More informationInstallation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No
Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION
More informationOWNER S GUIDE DUAL CONTROL THERMOSTATIC SHOWER VALVE. Shower Control. may differ depending on choice of Model. Concealing Plate. Handles and ISSUE 01
DUAL CONTROL THERMOSTATIC SHOWER VALVE Shower Control Handles and Concealing Plate may differ depending on choice of Model OWNER S GUIDE ISSUE 01 These instructions cover all exposed or concealed versions
More informationIMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS
Commander Cartridge Filter Operating Procedures IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Table of Contents SECTION I. FILTER INSTALLATION... 1 SECTION II.
More informationSEADUCER BOATS GAS SPORT HYDRO
SEADUCER BOATS GAS SPORT HYDRO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 2 - Pkg. Of 440 push rod ends 2 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 30" flex
More informationJacuzzi. J-CQ420 Cartridge Filter Installation and Operating Instructions
Jacuzzi J-CQ420 Cartridge Filter Installation and Operating Instructions IMPORTANT SAFETY PRECAUTIONS ATTENTION INSTALLER: This guide contains important information about the installation, operation and
More informationSERVICE MANUAL SALAMANDER BROILERS RADIANT AND INFRARED 36RB 36IRB VULCAN C36RB C36IRB WOLF
SERVICE MANUAL SALAMANDER BROILERS RADIANT AND INFRARED VULCAN 36RB 36IRB WOLF C36RB C36IRB This Manual is prepared for the use of trained Vulcan Service Technicians and should not be used by those not
More informationBASIN AND WALL MIXER INSTALLATION INSTRUCTIONS
BASIN AND WALL MIXER INSTALLATION INSTRUCTIONS IMPORTANT INFORMATION IMPORTANT All tapware and showers to be installed by a licensed plumber and to Australian Standards. Fit tempering and pressure reduction
More informationETL listed for installations within 5 ft. (1.5M) of outer edge of water
Fiberstars Light Streams Mini Laminar Installation Manual (LSML) 3072091 ETL listed for installations within 5 ft. (1.5M) of outer edge of water 79-15056-00 Rev. A Page 1 of 6 SAVE THESE INSTRUCTIONS!
More informationNAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS
NAVIGATOR PROP BUILDING INSTRUCTIONS & PHOTOS Science under the ice Ice sheet At regional competitions the ice is simulated by 8 ft x 4 ft ½-inch foam sheeting (Home Depot part #703990 [in store only],
More informationSpare parts list ( ) Spare parts list HDS 700 B
Spare parts list (5.955-875.0) Spare parts list HDS 700 B 02.09.2013 www.kaercher.com EN Page 2 Page 3 Page 4 Table of contents Spare parts list HDS 700 B (5.955-875.0)... 6 10 Individual parts... 7 11
More informationPO Box 1130 Ballston Lake, NY Tel. : (518) Fax: (518) Pool Skimmer
Tri Nuclear Corp. PO Box 1130 Ballston Lake, NY 12019 Tel. : (518) 399-1389 Fax: (518) 399-9586 E-mail: info@trinuclear.com Pool Skimmer Assembly & Operating Instructions Model SK-175 Document No: OI-12
More informationRG1200 Service and Repair Manual
Dive Rite RG 1200 Regulator Service and Repair Manual Page 1 Text and Photography by Pete Nawrocky Copyright ( ) 1999-2000, Lamartek, Inc., dba Dive Rite RG1200 Service and Repair Manual First Stage.........................................
More informationTo purchase replacement parts and accessories, or to obtain technical assistance, visit:
IMPORTANT Read this guide and follow all instructions carefully before assembling or using this product. To purchase replacement parts and accessories, or to obtain technical assistance, visit: www.splasharoundpools.com
More informationNORMAL OPERATING DISPLAYS GENERAL OPERATION
SunTapWat e rsys t e ms WS1Cl ac kwat e rsof t ne r Owne r smanual MAIN COMPONENTS Your water treatment system is a point of entry (POE) system composed of three components: A. The control valve and computer
More informationParts. Ultra 395/495/595t Ultra Max II 490/495/595t S. Korean patent VAC psi (228 bar, 22.8 MPa) Maximum Working Pressure
Parts Ultra 395/495/595t Ultra Max II 490/495/595t Korean patent 10--0579681 309675S EN 3300 psi (228 bar, 22.8 MPa) Maximum Working Pressure 0 VAC Type Stand Series Lo-boy Series Hi-boy Series Ultra 395t
More informationType S301 & S302 Gas Regulators INTRODUCTION INSTALLATION. Scope of Manual. Description. Specifications. Type S301 and S302. Instruction Manual
Fisher Controls Instruction Manual Type S301 & S302 Gas Regulators October 1981 Form 5180 WARNING Fisher regulators must be installed, operated, and maintained in accordance with federal, state, and local
More informationPaddle Bar Replacement
This procedure is to help facilitate the replacement of the 23 Paddle Bar Assembly on the ANKOM Dietary Fiber Analyzer. Note: The following items will be sent in a replacement package as part of the 23
More informationREVERSE OSMOSIS WATER FILTRATION SYSTEM MODEL EWR 4075 INSTRUCTION MANUAL
REVERSE OSMOSIS WATER FILTRATION SYSTEM MODEL EWR 4075 INSTRUCTION MANUAL Excalibur Water Systems 142 Commerce Park Drive, Unit M & N Barrie, Ontario L4N 8W8 CANADA www.excaliburwater.com 2013.05.7446
More informationHGC-200 Hydro Gas Chlorinator
HGC-200 Hydro Gas Chlorinator ProMinent Fluid Controls Pty Ltd Head Office: Unit 4, 4 Narabang Way BELROSE NSW 2085 AUSTRALIA (PO Box 85, BELROSE WEST NSW 2085) Phone: (02) 9450 0995 Fax: (02) 9450 0996
More informationINSTALLING AN INEXPENSIVE AIR LINE TO MEASURE WATER DEPTHS IN WELLS
INSTALLING AN INEXPENSIVE AIR LINE TO MEASURE WATER DEPTHS IN WELLS Joe Henggeler Extension Agricultural Engineer-Irrigation An inexpensive, yet highly accurate, device to measure the depth to water in
More informationINSTALLATION INSTRUCTIONS FOR GRT75-PF-RFS PET FOUNTAIN
INSTALLATION INSTRUCTIONS FOR GRT75-PF-RFS PET FOUNTAIN Important: Read all instructions and refer to local codes prior to installation. l Local soil conditions may require more gravel for drainage. l
More informationCARTRIDGE FILTERS. Models: CF50, CF75, CF100, CF150,
CARTRIDGE FILTERS Models: CF50, CF75, CF00, CF50, The installation of this product should be carried out by a qualified pool technician, following the installation instructions provided in this manual.
More informationRain Barrels. Did You Know?
Rain Barrels Rain barrels are water storage units designed to collect water from impermeable surfaces like roofs. The most common type of rain barrel collects runoff from roofs by connecting to gutter
More informationPRO SINK -R 1 and 2. Dilution system CONTENTS
PRO SINK -R 1 and 2 Dilution system CONTENTS 1.0 Product description 2 2.0 Warnings.. 3 3.0 Installation procedure 4 4.0 Plumbing connections 4 5.0 Technical features.. 5 6.0 Maintenance... 6 7.0 Troubleshooting......6
More informationSterisil Ac+ Installation & Operating Manual
Sterisil Ac+ Installation & Operating Manual 719 622 7200 Sterisil.com Arbor Dental Associates 2 Table of Contents Introduction 4 Sterisil Ac + Features 5 Installation Instructions 6 Maintenance 10 Troubleshooting
More information10 DRIP NOZZLE WATERING DRIP KIT Model / Model 46095
10 DRIP NOZZLE WATERING DRIP KIT Model 93261 / Model ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission
More informationINSTALLATION INSTRUCTIONS MANUAL ON/OFF SAFETY VALVE/PILOT KIT MODEL GA9050A-1 (F0235)
P/N 126905-01 Rev. B 11/2016 INSTALLATION INSTRUCTIONS MANUAL ON/OFF SAFETY VALVE/PILOT KIT MODEL GA9050A-1 (F0235) For All Single, Dual and Triple Burner Natural and Propane/LP Gas Logs P126905-01 For
More informationTANK MATE INCLUDES: TOOLS REQUIRED: CONRADER VALVES 3/4 WRENCH **TUBING CUTTERS TEE PETCOCK TEE ASSEMBLY 8 FOOT NYLON TUBING
CONRADER VALVES TANK MATE AUTOMATIC DRAIN VALVE INSTALLATION KIT INCLUDES: TEE PETCOCK TEE ASSEMBLY 8 FOOT NYLON TUBING WV-1 DRAIN VALVE TOOLS REQUIRED: 3/4 WRENCH **TUBING CUTTERS ** NEEDED TO CUT METAL
More information