INSTALLATION AND OPERATION MANUAL

Size: px
Start display at page:

Download "INSTALLATION AND OPERATION MANUAL"

Transcription

1 Please read THE enire CONTENTS OF THIS MANUAL prior o insallaion AND OPERATION. BY PROCEEDING YOU AGREE THAT YOU FULLY UNDERSTAND AND COMPREHEND THE FULL CONTENTS OF THIS MANUAL. Forward his manual o all operaors. Failure o operae his equipmen as direced may cause injury OR DEATH. REV E p/n INSTALLATION AND OPERATION MANUAL 6,000 Pound capaciy Low RISE LIFT MODELS: LR-60 LR-60P Keep his operaion manual near he machine a all imes. Make sure ha all users read his manual. SHIPPING DAMAGE CLAIMS When his equipmen is shipped, ile passes o he purchaser upon receip from he carrier. Consequenly, claims for he maerial damaged in shipmen mus be made by he purchaser agains he ransporaion company a he ime shipmen is received. BE SAFE Your new lif was designed and buil wih safey in mind. However, your overall safey can be increased by proper raining and houghful operaion on he par of he operaor. DO NOT operae or repair his equipmen wihou reading his manual and he imporan safey insrucions shown inside Lemonwood Dr. Sana Paula, CA , USA Toll Free Tel: Fax:

2 6000 POUND CAPACITY LOW-RISE LIFT This insrucion manual has been prepared especially for you. Your new lif is he produc of over 35 years of coninuous research, esing and developmen; i is he mos echnically advanced lif on he marke oday. READ THIS ENTIRE MANUAL BEFORE INSTALLATION & OPERATION BEGINS. RECORD HERE THE LIFT AND POWER UNIT INFORMATION WHICH IS LOCATED ON THE SERIAL NUMBER DATA PLATES ON THE LIFT AND ON THE POWER UNIT Power Uni Model # Power Uni Dae Of Mfg. Power Uni Serial # This informaion is required when calling for pars or warrany issues. PRODUCT WARRANTY BendPak Low Rise Lifs are covered under warrany for one year on equipmen srucure, o be free of defecs in maerial and workmanship. Power unis, hydraulic cylinders, and all oher assembly componens such as urnplaes, slip plaes, cables, chains, valves, swiches ec. are covered under warrany for one year agains defecs in maerial or workmanship under normal use. BendPak Inc. shall repair or replace a heir opion for he warrany period hose pars reurned o he facory freigh prepaid which prove upon inspecion o be defecive. BendPak Inc. will pay labor coss for he firs 12 monhs only on pars reurned as previously described. The warrany does no exend o... defecs caused by ordinary wear, abuse, misuse, shipping damage, improper insallaion, volage or lack of required mainenance; damages resuling from purchaser s neglec or failure o operae producs in accordance wih insrucions provided in he owner s manual(s) and/or oher accompanying insrucions supplied; normal wear iems or service normally required o mainain he produc in a safe operaing condiion; any componen damaged in shipmen; oher iems no lised bu may be considered general wear pars; damage caused by rain, excessive humidiy, corrosive environmens or oher conaminan s. THESE WARRANTIES DO NOT EXTEND TO ANY COSMETIC DEFECT NOT INTERFERING WITH EQUIPMENT FUNCTIONALITY OR ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF A BENDPAK INC. PRODUCT OR THE BREACH OR DELAY IN PERFORMANCE OF THE WARRANTY. WARRANTY IS NOT VALID UNLESS WARRANTY CARD IS RETURNED. 2

3 IMPORTANT NOTICE Do no aemp o insall his lif if you have never been rained on basic auomoive lif insallaion procedures. Never aemp o lif componens wihou proper lifing ools such as a forklif or cranes. Say clear of any moving pars ha can fall and cause injury. These insrucions mus be followed o insure proper insallaion and operaion of your lif. Failure o comply wih hese insrucions can resul in serious bodily harm and void produc warrany. Manufacurer will assume no liabiliy for loss or damage of any kind, expressed or implied resuling from improper insallaion or use of his produc. Please read enire manual prior o insallaion. Definiions of Hazard LEVELS Idenify he hazard levels used in his manual wih he following definiions and signal words: Owner s Responsibiliy To mainain he lif and user safey, he responsibiliy of he owner is o read and follow hese insrucions: Follow all insallaion and operaion insrucions. Make sure insallaion conforms o all applicable Local, Sae, and Federal Codes, Rules, and Regulaions; such as Sae and Federal OSHA Regulaions and Elecrical Codes. Carefully check he lif for correc iniial funcion. Read and follow he safey insrucions. Keep hem readily available for machine operaors. Make cerain all operaors are properly rained, know how o safely and correcly operae he uni, and are properly supervised. Allow uni operaion only wih all pars in place and operaing safely. Carefully inspec he uni on a regular basis and perform all mainenance as required. Service and mainain he uni only wih auhorized or approved replacemen pars. Keep all insrucions permanenly wih he uni and all decals on he uni clean and visible. Before You Begin DANGER Wach for his symbol: I Means: Immediae hazards which will resul in severe personal injury or deah. WARNING Wach for his symbol: I Means: Hazards or unsafe pracices which could resul in severe personal injury or deah. CAUTION Wach for his symbol: I Means: Hazards or unsafe pracices which may resul in minor personal injury, produc or propery damage. Receiving: The shipmen should be horoughly inspeced as soon as i is received. The signed bill of lading is acknowledgemen by he carrier of receip in good condiion of shipmen covered by your invoice. If any of he goods called for on his bill of lading are shored or damaged, do no accep hem unil he carrier makes a noaion on he freigh bill of he shored or damaged goods. Do his for your own proecion. NOTIFY THE CARRIER AT ONCE if any hidden loss or damage is discovered afer receip and reques he carrier o make an inspecion. If he carrier will no do so, prepare a signed saemen o he effec ha you have noified he carrier (on a specific dae) and ha he carrier has failed o comply wih your reques. IT IS DIFFICULT TO COLLECT FOR LOSS OR DAMAGE AFTER YOU HAVE GIVEN THE CARRIER A CLEAR RECEIPT. File your claim wih he carrier promply. Suppor your claim wih copies of he bill of lading, freigh bill, invoice, and phoographs, if available. Our willingness o assis in helping you process your claim does no make BendPak responsible for collecion of claims or replacemen of los or damaged maerials. 3

4 Table of Conens Conens Page No. Warrany / Serial Number Informaion Definiions of Hazard Levels Owner s Responsibiliy Before You Begin Insaller / Operaor Agreemen / Proecive Equipmen Inroducion Safey / Warning Insrucions Tools Required Sep 1 / Selecing Sie Sep 2 / Floor Requiremens Concree Specificaions Assembly View / Specificaions Sep 3 / Power Uni Se Up Sep 4 / Layou Sep 5 / Connecing Hydraulic Fiings / Hoses Sep 6 / Wiring Power Uni Sep 7 / Anchoring Lif (LR-60) Sep 8 / Insalling Wheel Assemblies (LR-60P) Sep 9 / Lif Sar Up / Final Adjusmens Sep 10 Bleeding Sep 11 / Operaion/ Mainenance Troubleshooing Guide Mainenance Records Opional Equipmen Insallaion Agreemen

5 INSTALLER / OPERATOR PLEASE READ AND FULLY UNDERSTAND. BY PROCEEDING YOU AGREE TO THE FOLLOWING. I have visually inspeced he sie where he lif is o be insalled and verified he concree o be in good condiion and free of cracks or oher defecs. I undersand ha insalling a lif on cracked or defecive concree could cause lif failure resuling in personal injury or deah. I undersand ha a level floor is required for proper insallaion and level lifing. Failure o follow danger, warning, and cauion insrucions may lead o serious personal injury or deah o operaor or bysander or damage o propery. Please read enire manual prior o insallaion. Do no operae his machine unil you read and undersand all he dangers, warnings and cauions in his manual. For addiional copies or furher informaion, conac: I undersand ha I am responsible if my floor is of quesionable slope and ha I will be responsible for all charges relaed o pouring a new level concree slab if required and any charges. I undersand ha he lifs are supplied wih concree faseners meeing he crieria of he American Naional Sandard Auomoive Lifs - Safey Requiremens for Consrucion, Tesing, and Validaion ANSI/ALI ALCTV- 2006, and ha I will be responsible for all charges relaed o any special regional srucural and/or seismic anchoring requiremens specified by any oher agencies and/or codes such as he Uniform Building Code (UBC) and/or Inernaional Building Code (IBC). I will assume full responsibiliy for he concree floor and condiion hereof, now or laer, where he above equipmen model(s) are o be insalled. I undersand ha Bendpak lifs are designed o be insalled in indoor locaions only. Failure o follow insallaion insrucions may lead o serious personal injury or deah o operaor or bysander or damage o propery or lif. BendPak Inc. / Ranger Producs 1645 Lemonwood Dr. Sana Paula, CA INSTALLER / OPERATOR Proecive Equipmen Personal proecive equipmen helps makes insallaion and operaion safer, however, does no ake he place of safe operaing pracices. Always wear durable work clohing during any insallaion and/or service aciviy. Shop aprons or shop coas may also be worn, however loose fiing clohing should be avoided. Tigh fiing l eaher gloves are recommended o proec echnician hands when handling pars. Surdy leaher work shoes wih seel oes and oil resisan soles should be used by all service personnel o help preven injury during ypical insallaion and operaion aciviies. Eye proecion is essenial during insallaion and operaion aciviies. Safey glasses wih side shields, goggles, or face shields are accepable. Back bels provide suppor during lifing aciviies and are also helpful in providing worker proecion. Consideraion should also be given o he use of hearing proecion if service aciviy is performed in an enclosed area, or if noise levels are high. THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OR YOURSELF AND OTHERS AND CAN CAUSE PERSONAL INJURY OR DEATH. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING TO OPERATE THIS MACHINE. 5

6 1. Carefully remove he craing and packing maerials. CAUTION! Be careful when cuing seel banding maerial as iems may become loose and fall causing personal harm or injury. INTRODUCTION IMPORTANT SAFETY INSTRUCTIONS! Read hese safey insrucions enirely! 2. Check he volage, phase and proper amperage requiremens for he moor shown on he moor plae. Wiring should be performed by a cerified elecrician only. IMPORTANT NOTICE! Do no aemp o insall his lif if you have never been rained on basic auomoive lif insallaion procedures. Never aemp o lif componens wihou proper lifing ools such as forklif or cranes. Say clear of any moving pars ha can fall and cause injury. 1. Read and undersand all safey warning procedures before operaing lif. 2. Keep hands and fee clear. Remove hands and fee from any moving pars. Keep fee clear of lif when lowering. Avoid pinch poins. 3. Keep work area clean. Cluered work areas invie injuries. 4. Consider work area environmen. Do no expose equipmen o rain. Do no use in damp or we locaions. Keep area well lighed. 5. Only rained operaors should operae his lif. All non-rained personnel should be kep away from work area. Never le non-rained personnel come in conac wih, or operae lif. 6. Use lif correcly. Use lif in he proper manner. Never use lifing adapers oher han wha is approved by he manufacurer. 12. Guard agains elecric shock. This lif mus be grounded while in use o proec he operaor from elecric shock. Never connec he green power cord wire o a live erminal. This is for ground only. 13. Danger! The power uni used on his lif conains high volage. Disconnec power a he recepacle before performing any elecrical repairs. Secure plug so ha i canno be accidenally plugged in during service. 14. Warning! Risk of explosion. This equipmen has inernal arcing or sparking pars which should no be exposed o flammable vapors. This machine should no be locaed in a recessed area or below floor level. 15. Mainain wih care. Keep lif clean for beer and safer performance. Follow manual for proper lubricaion and mainenance insrucions. Keep conrol handles and/or buons dry, clean and free from grease and oil. 7. Do no override self-closing lif conrols. 8. Remain clear of lif when raising or lowering vehicle. 9. Clear area if vehicle is in danger of falling. 10. Always insure ha he safeies are engaged before any aemp is made o work on or near vehicle. 11. Dress properly. Non-skid seel-oe foowear is recommended when operaing lif Say aler. Wach wha you are doing. Use common sense. Be aware. 17. Check for damaged pars. Check for alignmen of moving pars, breakage of pars or any condiion ha may affec is operaion. Do no use lif if any componen is broken or damaged. 18. Never remove safey relaed componens from he lif. Do no use lif if safey relaed componens are damaged or missing.

7 Roary Hammer Drill Or Similar * 3/4 Masonry Bi * 1-1/4 Masonry Bi * Hammer * Wrenches:SAE/ Meric* Medium Crescen Wrench STEP 1 (Selecing Sie) Before insalling your new lif, check he following: 1. LIFT LOCATION: Always use archiecs plans when available. Check layou dimension agains floor plan requiremens making sure ha adequae space is available. TOOLS REQUIRED Crow Bar For Shim Insallaion* Lifing Blocks / Sands* Hydraulic Jack / Lifing Device* Medium Screwdriver Tape Measure * Required for LR-60 IMPORTANT NOTICE! These insrucions mus be followed o insure proper insallaion and operaion of your lif. Failure o comply wih hese insrucions can resul in serious bodily harm and void produc warrany. Manufacurer will assume no liabiliy for loss or damage of any kind, expressed or implied resuling from improper insallaion or use of his produc. Please read enire manual prior o insallaion! A level floor is suggesed for proper use and insallaion and level lifing. If a floor is of quesionable slope, consider a survey of he sie and/ or he possibiliy of pouring a new level concree slab. 2. OVERHEAD OBSTRUCTIONS: The area where he lif will be locaed should be free of overhead obsrucions such as heaers, building suppors, elecrical lines ec. 3. DEFECTIVE FLOOR: Visually inspec he sie where he lif is o be insalled and check for cracked or defecive concree. DO NOT insall or use his lif on any asphal surface or any surface oher han concree. DO NOT insall or use his lif on expansion seams or on cracked or defecive concree. DO NOT insall or use his lif on a second / elevaed floor wihou firs consuling building archiec. DO NOT insall or use his lif oudoors. 4. OPERATING TEMPERATURE. Operae lif only beween emperaures of F. CONCRETE SPECIFICATIONS 5. Lif is designed for INDOOR INSTALLATION ONLY STEP 2 (Floor Requiremens) LIFT MODEL LR-60 LR-60P CONCRETE REQUIREMENT 3.5 Min Thickness / 2500PSI 3.5 Min Thickness / 2500PSI This lif mus be insalled on a solid level concree floor wih no more han 3-degrees of slope. Failure o do so could cause personal injury or deah. 7 DANGER! All models MUST be insalled on 2500 PSI concree only conforming o he minimum requiremens shown above. New concree mus be adequaely cured by a leas 28 days minimum. IMPORTANT NOTE: BendPak lifs are supplied wih insallaion insrucions and concree faseners meeing he crieria as prescribed by he American Naional Sandard "Auomoive Lifs - Safey Requiremens for Consrucion, Tesing, and Validaion" ANSI/ALI ALCTV Lif buyers are responsible for any special regional srucural and/or seismic anchoring requiremens specified by any oher agencies and/or codes such as he Uniform Building Code (UBC) and/or Inernaional Building Code (IBC).

8 When removing he lif from packaging pay close aenion as he lif can slide and can cause injury. PARTS INVENTORY Be sure o ake a complee invenory of pars prior o beginning insallaion. Assembly View QTY DESCRIPTION PART # CHECK 1 Main Frame Assembly Hydraulic Power Uni Moor Sand Lifing Blocks 1 1/ * Fiing; ; (Power Uni) Sraigh Fiing ; (Cylinder) M8 x 1.25 x 20 Hex Head Bols (Power Uni) M8 x 1.25 Hex Head Nus (Power Uni) M8 Fla Washer (Power Uni) Hydraulic Hose Assy. ( 6.35 x 3640mm) DS /4 x 4 Weji Anchors Tow handle (LR-60P Only) Wheel Assemblies (LR-60P Only) LR-60P Shown SPECIFICATIONS LR-60 LR-60-P Lifing Capaciy 6,000 Lbs. 6,000 Lbs. Lifing Heigh Lifing Time 36 Seconds 36 Seconds Frame Dimension 81-1/2 x /2 x 18 Lif Pad Dimensions 18 x x 32 Lowered Heigh 4 4 Safey Sysem Mechanical Locks Mechanical Locks Hydraulic Power Uni 110/220 Vol / 60HZ / 1 Phase 110/220 Vol / 60HZ / 1 Phase Fluid Capaciy 1-1/2 Gallons 1-1/2 Gallons

9 STEP 3 (Power Uni Se Up) 1. Se he Power Uni on he Sand and moun using he four M8 bols Nus and Fla Washers. (See Fig. 3.1) 3. Selec a sie for he Power Uni so ha operaors have a full, unobsruced view of he lif. STEP 5 (Connecing Hydraulic Fiings / Hoses) 1. Remove he plasic plug from he lef por of he Cylinder. (See Fig. 5.1) 2. Insall he Sraigh Hydraulic Fiing in he lef por of he Cylinder. Use Teflon Tape on he Cylinder side on he Fiing only. (See Fig. 5.1) Fig Fill he reservoir wih 6 Quars / 1.5 gals of Dexron III ATF or 10W Non-foaming hydraulic fluid. STEP 4 (Layou) 1. Remember ha he lif moves rearward approximaely 14 when raised. (See Fig. 4.1) Fig. 5.1 Connec one end of he 143 Hydraulic Hose Assy making sure o no over-ighen. Do no use Teflon Tape on his connecion. 3. Insall he 90-degree hydraulic Fiing in he pressure por of he Power Uni. The pressure por is covered wih a plasic plug. (See Fig 5.2) Fig Afer selecing a sie, place he uni in posiion making sure he Hydraulic Cylinder is placed owards he fron of he bay. (Engine should be posiioned a Cylinder side of lif.) (See Fig. 4.2) Fig. 5.2 Fig Connec he 143 Hydraulic Hose o he Power Uni fiing. Do no use Teflon Tape on his connecion, make sure o no over-ighen.

10 STEP 6 (Wiring Power Uni) 1. Have a cerified elecrician verify he power supply o he power uni. Refer o he daa plae found on he moor for proper power supply and wire size. DANGER! ALL WIRING MUST BE PERFORMED BY A LICENSED ELECTRICIAN. The sandard power uni can be run on eiher 110V or 220V. I is already wired for 110V and equipped wih a 3-wire power cord wih grounding plug. For opional 220V hook up, follow he wiring insrucions as shown on he moor daa plae. See elecrical daa WARNING! WARNING! The power uni on his lif MUST NOT ge we. NEVER expose power uni o we / damp condiions. Damage o power uni caused by moisure is no covered under warrany. DANGER! DO NOT PERFORM ANY MAINTENANCE OR INSTALLATION OF ANY COMPONENTS WITH OUT FIRST ENSURING THAT ELECTRICAL POWER HAS BEEN DISCONNECTED AT THE SOURCE OR PANEL AND CANNOT BE RE-ENERGIZED UNTIL ALL MAINTENANCE AND/OR INSTALLATION PROCEDURES ARE COMPLETED. WARNING! RISK OF EXPLOSION! This equipmen has inernal arcing or pars ha may spark and should no be exposed o flammable vapors. Moor should no be locaed in a recessed area or below floor level. NEVER expose moor o rain or oher damp environmens. DAMAGE TO MOTOR CAUSED BY WATER IS NOT COVERED UNDER WARRANTY. DO NOT run power uni wih no oil. Damage o pump can occur. The power uni mus be kep dry. Damage o power uni caused by waer or oher liquids such as deergens, acid ec., is no covered under warrany. Operae lif only beween emperaures of F. Improper elecrical hook-up can damage moor and will no be covered under warrany. Moor can no run on 50HZ wihou a physical change in moor. Use a separae breaker for each power uni. Proec each circui wih ime delay fuse or circui breaker. For vol, single phase, use a 20 amp fuse. For vol, single phase, use a 25 amp fuse. 10

11 STEP 7 (Anchoring Lif, LR-60 Only) 1. Using Hydraulic Jack or oher lifing device, raise he lif off he Ground approximaely Before anchoring lif o he floor, confirm he locaion is saisfacory. 2. Using a 3/4 concree bi, drill he floor using he holes on he frame as a guide. (See Fig. 7.1) 3. Remove all excess dus from holes, hen insall he anchor bols. (See Fig. 7.1) 4. Tighen he anchor bols o f.-lbs. using an open end wrench only. DO NOT use an impac wrench o ighen concree anchors. (See Fig. 7.1) Fig. 7.1 WARNING! Place lif on blocks or sands BEFORE proceeding wih any work under he lif. 2. Insall he eigh Fla Head Phillips Screws (four per side) up hrough he Flanges on he inside rails of he Lif. (See Fig. 8.3) Fig. 8.3 STEP 8 (Insalling Wheel Assemblies) (FOR LR-60-P ONLY) 1. Assemble he wo Wheel Assemblies as shown in Fig 8.1 and Insall he Wheel Assemblies as shown. Insall Spli Lock Washers and ighen Hex Head Bols. (See Fig. 8.4) Fig. 8.4 Fig. 8.1 Fig Remove any sands / blocks. Lower Lif back on he ground. WARNING! DO NOT OPERATE THE LIFT WITH THE WHEEL ASSEMBLIES IN THE DOWN POSITION. 11

12 TO MOVE LIFT 1. Pull up on Wheel Assembly handle. 2. Flip Down Wheel Pin. (See Fig. 8.5) Fig Tes he Power Uni by pressing he push-buon swich. If he moor sounds like i is operaing properly, raise he lif and check all hose connecions for leaks. If he moor ges ho or sounds peculiar, sop and check all elecrical connecions. WARNING! Keep hands and fee clear. Remove hands and fee from any moving pars. Keep fee clear of lif when lowering. Avoid pinch poins. Always wear safey goggles 3. Inser he Tow Handle ino he Tow Handle Anchor and push down on he Tow Handle o raise he Lif Assembly off he ground. (See Fig. 8.6) Fig Check he MAIN SAFETY LOCK o make sure i moves freely. Lubricae all SAFETY PIVOT poins wih WD-40 or equal. 4. Raise lif unil THE CYLINDER BOTTOMS OUT AND THE LIFT STOPS. 5. Lower he lif unil he Safey ress In he Locked Posiion. 6. Verify ha he Safey ress in he locked posiion a each safey sop. (See Fig. 9.1) Fig Remove he Tow Handle and Lower he Rear Wheel Assemblies. WARNING! DO NOT OPERATE THE LIFT WITH THE WHEEL ASSEMBLIES IN THE DOWN POSITION. STEP 9 (Lif Sar Up / Final Adjusmens) DANGER! CAUTION! During he START-UP procedure, observe all operaing componens and check for proper insallaion and adjusmen. DO NOT aemp o raise vehicle unil a horough operaional check has been compleed. 1. Confirm he Power Uni reservoir is full wih 6 quars/ 1.5 gals of 10-WT hydraulic oil or Dexron-III auomaic ransmission fluid. 12 Visually confirm ha ALL Primary Safey locks are engaged before enering work area. Suspension componens us on his lif are inended o raise and lower lif only and are no mean o be load holding devices. Remain clear of elevaed lif unless visual confirmaion is made ha all primary safey locks are fully engaged and he lif is LOWERED ono he safey locks, Refer o insallaion /operaion manual for proper safey lock procedures and /or furher insrucion.

13 TO LOWER LIFT: 1. Raise he lif off he Safey locks by pressing he push buon on he Power Uni. Make sure you raise he lif by a leas wo inches o allow adequae clearance for he Safey lock o clear. (See Fig. 9.2) Fig Lower lif by depressing lowering valve on Power Uni. 3. Run he lif up and down a few imes o insure ha he locks are engaging properly. Re-adjus or conac your insaller or Bendpak if necessary STEP 10 (Bleeding) 1. Lif mus be fully lowered before changing or adding fluid. 2. Raise and lower lif six imes. The Cylinder is selfbleeding. Afer bleeding sysem, fluid level in power uni reservoir may be down. Add more fluid if necessary o raise lif o full heigh. I is only necessary o add fluid o raise lif o full heigh. 3. To pressure es, run lif o full rise and run moor for approximaely 3-seconds afer lif sops. This will place pressure on he hydraulic sysem. Sop and check all fiings and hose connecions. Tighen or reseal if required. Pos-Insallaion Check-Off Lif Assembly, Level And Sable Elecric Power Supply Confirmed Safey Locks Funcioning Properly Check For Hydraulic Leaks Oil Level Lubricaion of Criical Componens Check For Overhead Obsrucions Runways Level All Screws, Bols, and Pins Secured Surrounding Area Clean Operaion, Mainenance and Safey Manuals on Sie 13

14 STEP 11 (Operaion Insrucions) OWNER/EMPLOYER RESPONSIBILITIES The Owner/Employer: Shall ensure ha lif operaors are qualified and ha hey are rained in he safe use and operaion of he lif using he manufacurer s operaing insrucions; ALI/SM01-1, ALI Lifing i Righ safey manual; ALI/ST-90 ALI Safey Tips card; ANSI/ALI ALOIM-2000, American Naional Sandard for Auomoive Lifs-Safey Requiremens for Operaion, Inspecion and Mainenance; ALI/WL Series, ALI Uniform Warning Label Decals/Placards; and in he case of frame engaging lifs, ALI/LP-GUIDE, Vehicle Lifing Poins/Quick Reference Guide for Frame Engaging Lifs. Shall esablish procedures o periodically inspec he lif in accordance wih he lif manufacurer s insrucions or ANSI/ALI ALOIM-2000, American Naional Sandard for Auomoive Lifs-Safey Requiremens for Operaion, Inspecion and Mainenance; and The Employer Shall ensure ha lif inspecors are qualified and ha hey are adequaely rained in he inspecion of he lif. Shall mainain he periodic inspecion and mainenance records recommended by he manufacurer or ANSI/ALI ALOIM-2000, American Naional Sandard for Auomoive Lifs-Safey Requiremens for Operaion, Inspecion and Mainenance. Shall display he lif manufacurer s operaing insrucions; ALI/SM 93-1, ALI Lifing i Righ safey manual; ALI/ST-90 ALI Safey Tips card; ANSI/ALI ALOIM-2000, American Naional Sandard for Auomoive Lifs-Safey Requiremens for Operaion, Inspecion and Mainenance; and in he case of frame engaging lifs, ALI/ LP-GUIDE, Vehicle Lifing Poins/Quick Reference Guide for Frame Engaging Lifs; in a conspicuous locaion in he lif area convenien o he operaor. Shall provide necessary lockou/agou means for energy sources per ANSI Z (R1993), Safey Requiremens for he Lockou/Tagou of Energy Sources, before beginning any lif repairs. Shall no modify he lif in any manner wihou he prior wrien consen of he manufacurer. Shall esablish procedures o periodically mainain he lif in accordance wih he lif manufacurer s insrucions or ANSI/ALI ALOIM-2000, American Naional Sandard for Auomoive Lifs-Safey Requiremens for Operaion, Inspecion and Mainenance; and The Employer Shall ensure ha lif mainenance personnel are qualified and ha hey are adequaely rained in he mainenance of he lif. 14

15 LIFT OPERATION SAFETY DAILY inspec your lif. Never operae if i malfuncions or if i has broken or damaged pars. Use only qualified lif service personnel and genuine BendPak pars o make repairs. THOROUGHLY rain all employees in use and care of lif, using manufacurer s insrucions and Lifing I Righ and Safey Tips supplied wih he lif. NEVER allow unauhorized or unrained persons o posiion vehicle or operae lif. PROHIBIT unauhorized persons from being in shop area while lif is in use. DO NOT permi anyone on lif or inside vehicle when i is eiher being raised or lowered. ALWAYS keep area around lif free of ools, debris, grease and oil. NEVER overload lif. Capaciy of lif is shown on nameplae affixed o he lif. DO NOT sand in fron of he vehicle while i is being posiioned in lif bay. DO NOT hi or run over lif arms or adapers. This could damage lif or vehicle. Before driving vehicle ino lif bay, posiion arms and adapers o provide unobsruced enrance ono lif. ALWAYS load vehicle on lif carefully. Posiion he lif adapers o conac a he vehicle manufacurer s recommended lif poins. Raise lif unil adapers conac vehicle. Check adapers for secure conac wih vehicle. Raise lif o desired working heigh. (See Fig.17.1) ALWAYS remain clear of lif when raising or lowering vehicles. ALWAYS use safey sands when removing or insalling heavy componens. DO NOT go under raised vehicle if safey locks are no engaged. DANGER! Visually confirm ha ALL Primary Safey locks are engaged before enering work area. Suspension componens us on his lif are inended o raise and lower lif only and are no mean o be load holding devices. Remain clear of elevaed lif unless visual confirmaion is made ha all primary safey locks are fully engaged and he lif is LOWERED ono he safey locks, Refer o insallaion /operaion manual for proper safey lock procedures and /or furher insrucion. NEVER LEAVE LIFT IN ELEVATED CONDITION unless all Safey Locks are engaged. AVOID excessive rocking of vehicle while on lif. ALWAYS CLEAR AREA if vehicle is in danger of falling. When lowering he lif PAY CAREFUL ATTENTION ha all personnel and objecs are kep clear. ALWAYS keep a visual line of sie on he lif AT ALL TIMES. ALWAYS make sure ha ALL LOCKS are disengaged. If one of he locks inadverenly locks on descen he lif and/or vehicle may disrup causing personal injury or deah, DO NOT block open or override self-closing lif conrols; hey are designed o reurn o he Off or Neural posiion when released. DO NOT remove or disable arm resrains. Fig ALWAYS REMOVE ool rays, sands, ec. before lowering lif. ALWAYS RELEASE safey locks before aemping o lower lif. ALWAYS POSITION he lif arms and adapers o provide an unobsruced exi before removing vehicle from lif area. 15

16 TO RAISE THE LIFT WARNING! WARNING! To avoid personal injury and/or propery damage, permi only rained personnel o operae lif. Afer reviewing hese insrucions, ge familiar wih lif conrols by running he lif hrough a few cycles before loading vehicle on lif. Always lif he vehicle using all four adapers. NEVER raise jus one end, one corner, or one side of vehicle. Many specialy or modified vehicles canno be raised on a wo-pos frame engaging lif. Conac vehicle manufacurer for raising or jacking deails. TYPICAL LIFTING POINTS 1. Before Loading: Lif mus be fully lowered and service bay clear of all personnel before he vehicle is brough on lif wih he arms (if used) se o he full drive-hru posiion. 2. Loading: Posiion arms under vehicle and posiion adapers a vehicle manufacurer s recommended lif poins. Use heigh exenders or opional frame-cradle adapers (if applicable) when necessary o ensure good conac. (See Fig ) Fig Fig Some vehicles may have he manufacurer's Service Garage Lif Poin locaions idenified by riangle shape marks on he undercarriage (reference ANSI/SAE J ). Also, here may be a label locaed on he righ fron door jamb area showing specific vehicle lif poins Posiion vehicle for proper weigh disribuion arms under vehicle o allow adapers /pads o conac a he manufacurer s recommended pick up poins.

17 5. If he specific vehicle lif poins are no idenified, or if he vehicle has addiional or uniquely posiioned payload, have a qualified person calculae he vehicle cener of graviy or have he vehicle cener of graviy deermined a a vehicle scale. Load he vehicle wih he ener of graviy midway beween adapers. WARNING! DO NOT Park wheels direcly on lif pads. 6. Se parking brake or use wheel chock o hold vehicle in posiion. Make sure vehicle is neiher fron nor rear heavy and selec he proper configuraion for he vehicle o be lifed as shown below. Cener of balance should be midway beween adapers and cenered over he lif. 17

18 7. Push he RAISE buon or roae he conrol swich on he power uni. Imporan Noe: Allow (2) seconds beween moor sars. Failure o comply may cause moor burnou. 8. Sop before making conac wih vehicle. Check conac poins. If required, slighly move arms or vehicle o allow resrain gear and pawl o mesh. 9. Raise vehicle unil ires clear he floor. 10. Sop and check adapers for secure conac a vehicle manufacurer s recommended lif poins. 11. Coninue o raise o desired heigh only if vehicle is secure on lif. 12. DO NOT go near or under a raised vehicle if all four adapers are no in secure conac wih vehicle a vehicle manufacurer s recommended lif poins. 13. Repea enire loading and raising procedures if required. 14. Lower lif ono safey locks. CLEAR AREA if vehicle is in danger of falling. DO NOT posiion yourself beween a wall and he lif. If he vehicle falls in ha direcion, you may be severely injured. Before aemping o lif pickup rucks or oher ruck frame vehicles, be sure ha: Vehicle frame is srong enough o suppor is weigh and has no been weakened by modificaion or corrosion. Vehicle individual axle weigh does no exceed one-half lif capaciy. Adapers are in secure conac wih frame a vehicle manufacurers recommended lif poins. Vehicle is sable on lif and neiher fron nor ail heavy. WHILE USING LIFT Avoid excessive rocking of vehicle while on lif. Always use safey sands as needed or when removing or insalling heavy componens. DO NOT ener work area or go under vehicle if safey locks are no engaged. TO LOWER THE LIFT DANGER! Visually confirm ha ALL Primary Safey locks are engaged before enering work area. Suspension componens us on his lif are inended o raise and lower lif only and are no mean o be load holding devices. Remain clear of elevaed lif unless visual confirmaion is made ha all primary safey locks are fully engaged and he lif is LOWERED ono he safey locks, Refer o insallaion /operaion manual for proper safey lock procedures and /or furher insrucion. WARNING! When lowering he lif PAY CAREFUL ATTENTION ha all personnel and objecs are kep clear. ALWAYS keep a visual line of sie on he lif AT ALL TIMES. ALWAYS make sure ha ALL LOCKS are disengaged. If one of he locks inadverenly locks on descen he lif and/or vehicle may disrup causing personal injury or deah. 1. Remove all ools or oher objecs from he lif area. 2. Raise lif off safey locks. Make sure you raise he lif by a leas wo inches o allow adequae clearance for he locks o clear. 3. Confirm safey lock is in unlocked posiion. 18

19 MAINTENANCE INSTRUCTIONS CAUTION! 4. Push LOWERING valve handle o lower. Do no override self-closing lif conrols. 5. Remain clear of lif when lowering vehicle. Observe pinch poin warning decals. 6. Remove adapers from under vehicle and arms o full drive-hru posiion before moving vehicle. 7. If lif is no operaing properly, Do No use unil adjusmen or repairs are made by qualified lif service personnel. If you are no compleely familiar wih auomoive lif mainenance procedures; STOP: Conac facory for insrucions. To avoid personal injury, permi only qualified personnel o perform mainenance on his equipmen. Always keep bols igh. Check periodically. Always keep lif componens clean. Always if oil leakage is observed, call local service represenaive. Always if elecrical problems develop, call local service represenaive. Always replace ALL FAULTY PARTS before lif is pu back ino operaion. Daily: Make a visual inspecion of ALL MOVING PARTS and check for excessive signs of wear. Daily: Check Safey Locks o insure hey are in good operaing condiion. Daily: Check pivo poins and hinges for wear. Replace worn pars as required wih genuine BendPak pars. Daily: Inspec adapers for damage or excessive wear. Replace as required wih genuine BendPak pars. Weekly: Lubricae any rollers wih general purpose oil or WD-40. Lubricae arm Hinge Pins wih grease. Weekly: Check bols and pins o insure proper mouning. Monhly: Lubricae locking lach shafs. Push lach handle several imes for oil o penerae pivo poins. Every 3 Monhs: Check anchor bols for ighness. Anchors should be orqued o 90 f/lbs. Semi-Annually: Check fluid level of lif power uni and refill if required per lif insallaion insrucions. Replace all cauion, warning or safey relaed decals on he lif if unable o read or missing. Reorder labels from BendPak. 19 Refer o ANSI/ALI ALOIM bookle for periodic inspecion checklis and mainenance log shee.

20 Safe Lif Operaion Auomoive and ruck lifs are criical o he operaion and profiabiliy of your business. The safe use of his and oher lifs in your shop is criical in prevening employee injuries and damage o cusomer s vehicles. By operaing lifs safely you can insure ha your shop is profiable, producive and safe. Safe operaion of auomoive lifs requires ha only rained employees should be allowed o use he lif. Training should include, bu not limied o: Proper posiioning of he vehicle on he runway. (See manufacurers minimize wheel base loading requiremens.) Use of he operaing conrols. Undersanding he lif capaciy. Proper use of jack sands or oher load supporing devices. Proper use, undersanding and visual idenificaion of safey lock devices and heir operaion. Reviewing he safey rules. Proper housekeeping procedures (lif area should be free of grease, oil, ools, equipmen, rash, and oher debris) A daily inspecion of he lif should be compleed prior o is use. Safey devices, operaing conrols, lif arms and oher criical pars should be inspeced prior o using he lif. All mainenance and repairs of he lif should be compleed by following he manufacurer s requiremens. Lif repair pars should mee or exceed OEM specificaions. Repairs should only be compleed by a qualified lif echnician. The vehicle manufacurer s recommendaions should be used for spoing and lifing he vehicle. Lif Operaion Safey I is imporan ha you know he load limi. Be careful ha you do no overload he lif. If you are unsure wha he load limi is, check he daa plae found on one of he lif columns or conac he manufacurer. The cener of graviy should be followed closely o wha he manufacurer recommends. Always make sure you have proper overhead clearance. Addiionally, check ha aachmens, ( vehicle signs, campers, anennas, ec.) are no in he way. Be sure ha prior o he vehicle being raised, he doors, runk, and hood are closed securely Prior o being raised, make sure here is no one sanding closer han six fee from he lif Afer posiioning he vehicle on he lif runways, se he emergency brake, make sure he igniion is off, he doors are closed, overhead obsrucions are cleared, and he ransmission is in neural. Double check ha he auomaic chock devices are in posiion and hen when he lif is raised, observe he chocks Pu pads or adapers in he righ posiion under he conac poins ha have been recommended The lif should be raised jus unil he vehicle s wheels are abou one foo off he ground. If conac wih he vehicle is uneven or i appears ha he vehicle is no siing secure, carefully lower he lif and readjus. Always consider poenial problems ha migh cause a vehicle o slip, i.e., heavy cargo, undercoaing, ec. Pay aenion when walking under a vehicle ha is up on he hydraulic lif. 20

21 Do no Leave he conrols while he lif is sill in moion. Do no sand direcly in fron of he vehicle or in he bay when vehicle is being loaded or driven ino posiion. Do no Go near vehicle or aemp o work on he vehicle when being raised or lowered. Remain clear of lif when raising or lowering vehicle. Do no rock he vehicle while on he lif or remove any heavy componen from vehicle ha may cause excessive weigh shif. Do no lower he vehicle unil people, maerials, and ools are clear. Always insure ha he safeies are engaged before any aemp is made o work on or near vehicle. Some vehicle mainenance and repair aciviies may cause he vehicle o shif. Follow he manufacurer s guidelines when performing hese operaions. The use of jack sands or alernae lif poins may be required when compleing some repairs. Read and undersand all safey warning procedures before operaing lif. Keep hands and fee clear. Remove hands and fee from any moving pars. Keep fee clear of lif when lowering. Avoid pinch poins. Only rained operaors should operae his lif. All non-rained personnel should be kep away from work area. Never le non-rained personnel come in conac wih, or operae lif. Use lif correcly. Use lif in he proper manner. Never use lifing adapers oher han wha is approved by he manufacurer. Do no override self-closing lif conrols. Clear area if vehicle is on danger of falling. Say aler. Wach wha you are doing. Use common sense. Be aware. Check for damaged pars. Check for alignmen of moving pars, breakage of pars or any condiion ha may affec is operaion. Do no use lif if any componen is broken or damaged. Never remove safey relaed componens from he lif. Do no use lif if safey relaed componens are damaged or missing. When he lif is being lowered, make sure everyone is sanding a leas six fee away. Be sure here are no jacks, ools, equipmen, lef under he lif before lowering. Always lower he vehicle down slowly and smoohly. 21

22 22

23 23

24 LIFT WILL NOT RAISE POSSIBLE CAUSE 1. Air in oil, (1,2,8,13) 2. Cylinder binding, (9) 3. Cylinder leaks inernally, (9) 4. Moor run backward under pressure, (11) 5. Lowering valve leaks, (3,4,6,10,11) 6. Moor runs backwards, (7,14,11) 7. Pump damaged, (10,11) 8. Pump won prime, (1,8,13,14,3,12,10,11) 9. Relief valve leaks, (10,11) 10. Volage o moor incorrec, (7,14,11) Remedy Insrucion 1. Check for proper oil level The oil level should be up o he bleed screw in he reservoir wih he lif all he way down. 2. Bleed cylinders See Insallaion Manual 3. Flush- Release valve o ge rid of Hold release handle down and sar uni possible conaminaion allowing i o run for 15 seconds. 4. Diry oil Replace oil wih clean Dexron ATF. 5. Tighen all faseners Tighen faseners o recommended orques. 6. Check for free movemen of release If handle does no move freely, replace bracke or handle assembly. 7. Check moor is wired correcly compare wiring of moor o elecrical diagram on drawing. 8. Oil seal damaged or cocked replace oil seal around pump shaf. 9. See Insallaion Manual Consul Lif Manufacurer. 10. Replace wih new par Replace wih new par. 11. Reurn uni for repair Reurn uni for repair. 12. Check pump-mouning bols Bols should be 15 o 18 f. lbs. 13. Inle screen clogged Clean inle screen or replace. 14. Check wall oule volages and wiring make sure uni and wall oule are wired properly. 24

25 MOTOR WILL NOT RUN POSSIBLE CAUSE 1. Fuse blown, (5,2,1,3,4) 2. Microswich burned ou, (1,2,3,4) 3. Moor burned ou, (1,2,3,4,6) 5. Volage o moor incorrec, (2,1,8) Remedy insrucion 1. Check for correc volage compare supply volage wih volage on moor nameag. Check ha he wire is sized correcly. N.E.C. able requires AWG 10 for 25 Amps. 2. Check moor is wired correcly compare wiring of moor o elecrical diagram on drawing. 3. Don use exension cords According o N.E.C. : The size of he conducors should be such ha he volage drop would no exceed 3% o he farhes oule for power Do no run moor a 115 VAC damage o he moor will occur. 4. Replace wih new par replace wih new par. 5. Rese circui breaker/fuse rese circui breaker/fuse. 6. Reurn uni for repair Reurn uni for repair. 7. See Insallaion Manual See Insallaion Manual. 8. Check wall oule volage and wiring Make sure uni and wall oule is wired properly. Moor mus run a 208/230 VAC. LIFT LOWERS SLOWLY OR NOT AT ALL POSSIBLE CAUSE 1. Cylinders binding, (1) 2. Release valve clogged, (5,4,2,3) 3. Pressure fiing oo long, (6) 4. Air in Cylinder (7) Remedy insrucion 1. See Insallaion Manual Consul Lif Manufacurer. 2. Replace wih new par replace wih new par. 3. Reurn for repair Reurn for repair. 4. Check oil Use clean 10-WT hydraulic oil or Dexron-III auomaic ransmission fluid only. If ATF is conaminaed, replace wih clean ATF and clean enire sysem. 5. Clean release valve wash release valve in solven and blow ou wih air. 6. Replace fiing wih shor hread lead Replace fiing wih shor hread lead. 7. Bleed cylinders See Insallaion Manual 25

26 WILL NOT RAISE LOADED LIFT POSSIBLE CAUSE 1. Air in oil, (1,2,3,4) 2. Cylinder binding, (5) 3. Cylinder leaks inernally, (5) 4. Lif overloaded, (6,5) 5. Lowering valve leaks, (7,8,1,5,9) 6. Moor runs backwards, (10,12,9) 7. Pump damaged, (5,9) 8. Pump won prime, (1,2,3,4,5,11,9) 9. Relief valve leaks, (8,5,9) 10. Volage o moor incorrec, (10,12,5) Remedy insrucion 1. Check oil level The oil level should be up o he bleed screw in he reservoir [wih he lif all he way down.] 2. Check/Tighen inle ubes Replace inle hose assembly. 3. Oil seal damaged or cocked Replace oil seal and insall. 4. Bleed cylinders See Insallaion Manual. 5. See Insallaion Manual Consul Lif Manufacurer. 6. Check vehicle weigh Compare weigh of vehicle o weigh limi of he lif. 7. Flush release valve Hold release handle down and sar uni allowing i o run for 15 seconds. 8. Replace wih new par Replace wih new par. 9. Reurn uni for repair Reurn uni for repair. 10. Check moor is wired correcly Compare wiring of moor o elecrical diagram on power uni drawing. 11. Inle screen clogged Clean inle screen or replace. 12. Check wall oule volage and wiring make sure uni and wall oule is wired properly. 26

27 LIFT WILL NOT STAY UP POSSIBLE CAUSE 1. Air in oil, (1,2,3) 2. Check valve leaks, (6) 3. Cylinders leak inernally, (7) 4. Lowering valve leaks, (4,5,1,7,6) 5. Leaking fiings, (8) Remedy insrucion 1. Check oil level the oil level should be up o he bleed screw in he reservoir wih he lif all he way down. 2. Oil seal damaged and cocked Replace oil seal around pump shaf. 3. Bleed cylinder Refer o Insallaion Manual. 4. Flush release valve Hold release handle down and sar uni allowing i o run for 15 seconds. 5. Replace wih new valve Replace wih new valve. 6. Reurn uni for repair Reurn uni for repair. 7. See Insallaion Manual Consul Lif Manufacurer. 8. Check complee hydraulic sysem for leaks Tighen all hydraulics fiings and inspec all hoses. 27

28 Mainenance RECORDS 28

29 Mainenance RECORDS 29

30 30

31 31

32 For Pars Or Service Conac: Bend-Pak Inc. / Ranger Producs 1645 Lemonwood Dr. Sana Paula, CA Tel: Toll Free: Fax: p/n

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL 1,000 POUND CAPACITY MOTORCYCLE / ATV LIFT IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL INSTALLATION AND OPERATION MANUAL 6,000 POUND CAPACITY PORTABLE MID RISE LIFT MODEL: MD-6XP PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL INSTALLATION AND OPERATION MANUAL PARKING LIFT / 7,000 POUND CAPACITY PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING YOU AGREE THAT YOU FULLY UNDERSTAND

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT INSTALLATION AND OPERATION YOU AGREE THAT

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL EUROPEAN USERS 400V 50Hz SUPPLY DETAILS ARE INCLUDED WITH ELECTRICAL CON- TROL BOX. DISREGARD SUPPLY WIR- ING DETAILS IN THIS MANUAL 14,000 POUND CAPACITY COMMERCIAL GRADE FOUR-POST LIFTS IMPORTANT SAFETY

More information

Dannmar EQUIPMENT SX-6/XL USER MANUAL. Dannmar Equipment 646 Flinn Avenue, Suite A Moorpark, CA Tel:

Dannmar EQUIPMENT SX-6/XL USER MANUAL. Dannmar Equipment 646 Flinn Avenue, Suite A Moorpark, CA Tel: Dannmar Equipmen 646 Flinn Avenue, Suie A Moorpark, CA 93021 Tel: 1-877-432-6627 www.dannmar.com Dannmar R EQUIPMENT SX-6/XL USER MANUAL PORTABLE MID-RISE SCISSOR LIFT 6,000 POUND CAPACITY Also known as

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL EUROPEAN USERS 400V 50Hz SUPPLY DETAILS ARE INCLUDED WITH ELECTRICAL CONTROL BOX. DISREGARD SUPPLY WIRING DETAILS IN THIS MANUAL INSTALLATION AND OPERATION MANUAL HEAVY-DUTY FOUR-POST ALIGNMENT LIFTS Models:

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL EUROPEAN USERS 400V 50Hz SUPPLY DETAILS ARE INCLUDED WITH ELECTRICAL CONTROL BOX. DISREGARD SUPPLY WIRING DETAILS IN THIS MANUAL IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ THE ENTIRE

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL IMPORTANT SAFETY INSTRUCTIONS PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING WITH LIFT INSTALLATION AND OPERATION YOU AGREE THAT YOU FULLY UNDERSTAND

More information

QUICKJACK WARNING INSTALLATION AND OPERATION MANUAL MODELS: BL-3500 BL ,500 / 5,000 POUND CAPACITY QUICKJACK

QUICKJACK WARNING INSTALLATION AND OPERATION MANUAL MODELS: BL-3500 BL ,500 / 5,000 POUND CAPACITY QUICKJACK ! IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ THE ENTIRE CONTENTS OF THIS MANUAL PRIOR TO INSTALLATION AND OPERATION. BY PROCEEDING WITH JACK INSTALLATION AND OPERATION YOU AGREE

More information

XSz 8... XSz 50 Solenoid actuated fail-safe safety valve

XSz 8... XSz 50 Solenoid actuated fail-safe safety valve > > /-way or size: G /4... G, /4... NT > > ouble valve conrol sysem, inherenly failsafe wihou residual pressure > > ynamic self monioring > > For use wih pneumaic cluch and brake sysems and oher -way safey

More information

Instruction Manual. Rugged PCB type. 1 Terminal Block. 2 Function. 3 Series Operation and Parallel Operation. 4 Assembling and Installation Method

Instruction Manual. Rugged PCB type. 1 Terminal Block. 2 Function. 3 Series Operation and Parallel Operation. 4 Assembling and Installation Method Rugged PCB ype Insrucion Manual 1 Terminal Block Funcion.1...4.5.6.7 Inpu volage range Inrush curren limiing Overcurren proecion Overvolage proecion Oupu volage adjusmen range Isolaion Remoe ON/OFF E9

More information

3 (R) 1 (P) N/en

3 (R) 1 (P) N/en 3/ way fail-safe safey valve, solenoid acuaed For mechanical presses and oher safey applicaions G /4... G, /4... NT Inherenly fail-safe wihou residual pressure ynamic self monioring ouble valve conrol

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL EUROPEN USERS 400V 0Hz SUPPLY DETILS RE IN- CLUDED WITH ELECTRICL CONTROL BOX. DISREGRD SUPPLY WIRING DETILS IN THIS MNUL IMPORTNT SFETY INSTRUCTIONS SVE THESE INSTRUCTIONS PLESE RED THE ENTIRE CONTENTS

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL EUROPEN USERS 400V 50Hz SUPPLY DETILS RE INCLUDED WITH ELECTRICL CONTROL BOX. DISREGRD SUPPLY WIRING DETILS IN THIS MNUL IMPORTNT SFETY INSTRUCTIONS SVE THESE INSTRUCTIONS PLESE RED THE ENTIRE CONTENTS

More information

Automatic air-main charging and pressure control system for compressed air supplies

Automatic air-main charging and pressure control system for compressed air supplies Auomaic air-main charging and pressure conrol sysem for compressed air supplies Type PCS A module from he sysem -vacorol Swiching on-off a compressed air uni in a compressed air supply generally akes place

More information

Patent NO: 8,430,895. Revision (3) OPERATION INSTRUCTIONS. Fully Automatic AirGun by Air-Ordnance. HPA (High Pressure Compressed Air)

Patent NO: 8,430,895. Revision (3) OPERATION INSTRUCTIONS. Fully Automatic AirGun by Air-Ordnance. HPA (High Pressure Compressed Air) Paen NO: 8,430,895 Fully Auomaic AirGun by Air-Ordnance Powered by: Co2 Nirogen HPA (High Pressure Compressed Air) OPERATION INSTRUCTIONS Revision (3) 6-2013 1. Please read his owner s manual compleely.

More information

LSU RISK ASSESSMENT FORM Please read How to Complete a Risk Assessment before completion

LSU RISK ASSESSMENT FORM Please read How to Complete a Risk Assessment before completion Please read How o Complee a Risk Assessmen before compleion EVENT OR ACTIVITY BEING RISK ASSESSED (add name of even where relevan) NAME OF DEPARTMENT Squad Training Neball DATE OF COMPLETION OF RISK ASSESSMENT

More information

Type 14 Flanged Diaphragm

Type 14 Flanged Diaphragm izes: Body Maerials: Bonne Maerials: Diaphragms: pecificaions /" ", C, and,, G and EPDM and Also available in Nirile and FKM Type Flanged Diaphragm andard Feaures Flanged (ANI) face-o-face dimensions are

More information

Flow Switch LABO-VHZ-S

Flow Switch LABO-VHZ-S Flow Swich S Volumeric flow swiching Almos no effec from differing viscosiies Versaile, configurable swiching oupu in push-pull design Robus consrucion Compac design Characerisics he VHZ gearwheel flow

More information

INSTALLATION AND OPERATION MANUAL

INSTALLATION AND OPERATION MANUAL EUROPEAN USERS 400V 0Hz SUPPLY DETAILS ARE IN- CLUDED WITH ELECTRICAL CONTROL BOX. DISREGARD SUPPLY WIRING DETAILS IN THIS MANUAL INSTALLATION AND OPERATION MANUAL 9,000 POUND CAPACITY COMMERCIAL GRADE

More information

Zelio Control Measurement Relays RM4L Liquid Level Relays

Zelio Control Measurement Relays RM4L Liquid Level Relays Zelio Conrol Measuremen elays FNCTIONS These devices monior he levels of conducive liquids. They conrol he acuaion of pumps or valves o regulae levels; hey are also suiable for proecing submersible pumps

More information

Filter Regulator with Back Flow Mechanism AW20K/30K/40K. How to Order. Symbol. Note 4) J N R W Z. Note 5) Note 6) Accessories Note 3) Symbol.

Filter Regulator with Back Flow Mechanism AW20K/30K/40K. How to Order. Symbol. Note 4) J N R W Z. Note 5) Note 6) Accessories Note 3) Symbol. Filer Regulaor wih ack Flow Mechanism K/3K/4K 3 K F 3 ow o Order ircui diagram 3 4K K hen he air supply is cu off and releasing he inle pressure o he amosphere, he residual pressure release of he oule

More information

Owner s Manual SSCI. Wheeling, IL (800) Form No /08

Owner s Manual SSCI. Wheeling, IL (800) Form No /08 Owner s Manual Classic Bahing Table wih Access Door! Convenien Access Door & Roaing Ramp! Selec,, or Fauce Locaion! Pick 48-in or 60-in Table Widh! Choice of Inegral Splash Shields Model Numbers: 13022-LA-HJJRDR

More information

What the Puck? an exploration of Two-Dimensional collisions

What the Puck? an exploration of Two-Dimensional collisions Wha he Puck? an exploraion of Two-Dimensional collisions 1) Have you ever played 8-Ball pool and los he game because you scrached while aemping o sink he 8-Ball in a corner pocke? Skech he sho below: Each

More information

HafcoVac Compressed Air Industrial Vacuum Product Line

HafcoVac Compressed Air Industrial Vacuum Product Line HafcoVac Compressed Air Indusrial Vacuum Produc Line OPERATING INSTRUCTIONS & SAFETY MANUAL Thank you for your purchase of a HafcoVac produc. HafcoVac is a division of Hafco Foundry and Machine Company,

More information

CMA DiRECtions for ADMinistRAtion GRADE 6. California Modified Assessment. test Examiner and Proctor Responsibilities

CMA DiRECtions for ADMinistRAtion GRADE 6. California Modified Assessment. test Examiner and Proctor Responsibilities CMA 2012 California Modified Assessmen GRADE 6 DiRECions for ADMinisRAion es Examiner and Procor Responsibiliies Compleing all of he following seps will help ensure ha no esing irregulariies occur, ha

More information

Type Control action Setpoint range Air Weight Volume flow % capacity I n /h kg. Pressure diff. 1) Pa

Type Control action Setpoint range Air Weight Volume flow % capacity I n /h kg. Pressure diff. 1) Pa 7.0/ RL 0 & 0: neumaic volume-flow conroller Used in conjuncion wih an orifice plae or a dnamic pressure sensor and a pneumaic damper drive for conrolling he air volume in air-condiioning ssems. For fixed,

More information

MCW100A, B Time Proportional Rotary Position Controller

MCW100A, B Time Proportional Rotary Position Controller DESCRIPTION MCW100A, B Time Proporional Roary Posiion Conroller Issued: March 1992 The MCW100 Time Proporional Roary Posiion Conroller provides auomaic grade or seering conrol of paving, renching and curbing

More information

2020 ClearTrace In-line Turbidity System

2020 ClearTrace In-line Turbidity System 2020 ClearTrace In-line Turbidiy Sysem Code 5-0113-24V Code 5-0113-110V Preface This insrucion manual serves o explain he use of he LaMoe 2020 ClearTrace Inline Turbidiy Sysem and is wrien o cover as

More information

67.301/1. RLP 10: Pneumatic volume-flow controller. Sauter Components

67.301/1. RLP 10: Pneumatic volume-flow controller. Sauter Components 7.0/ RL 0: neumaic volume-flow conroller How energ efficienc is improved For demand-led conrol of he air volume in office rooms. Areas of applicaion Conrol of he suppl and exhaus air of individual rooms

More information

Installation & Technical Handbook for Marsh Industries Products

Installation & Technical Handbook for Marsh Industries Products Insallaion & echnical Handbook for Marsh Indusries Producs Page 4 Ensign Sewage Plan, Uni:Gem and Five Filer Insallaion 6 Ulra Polylok Insallaion 8 Sepic ank Insallaion 10 Marsh Ensign ank Dimensions 12

More information

TRACK PROCEDURES 2016 RACE DAY

TRACK PROCEDURES 2016 RACE DAY TRACK PROCEDURES 2016 RACE DAY Pi gaes will officially open a 4:00pm for regular programs. Big shows will have earlier opening imes. Hauler parking may be available approximaely 1 hour prior o pi gaes

More information

SPECIAL WIRE ROPES The Value Line

SPECIAL WIRE ROPES The Value Line SPECIAL WIRE ROPES The Value Line INTRODUCTION Qualiy Producs, Ousanding Service and Comprehensive Technical Suppor I s wha oday s indusries expec from heir supplier parners. And ha s wha WireCo WorldGroup

More information

Avoiding Component Failure in Industrial Refrigeration Systems

Avoiding Component Failure in Industrial Refrigeration Systems Avoiding Componen Failure in Indusrial Refrigeraion Sysems By Tim Kroeger, segmen markeing manager indusrial refrigeraion, Asia Pacific & India The aricle caegorises and gives examples of ypical componen

More information

Clemco Industries Corp. ISO 9001 Certified

Clemco Industries Corp. ISO 9001 Certified Clemco Indusries Corp. ISO 9001 Cerified 6 cuf Classic Blas Machines Exclusively from... SIMPLE, RUGGED, RELIABLE More han 75 years of reliable field service have made Clemco blas machines he preferred

More information

Using Rates of Change to Create a Graphical Model. LEARN ABOUT the Math. Create a speed versus time graph for Steve s walk to work.

Using Rates of Change to Create a Graphical Model. LEARN ABOUT the Math. Create a speed versus time graph for Steve s walk to work. 2.4 Using Raes of Change o Creae a Graphical Model YOU WILL NEED graphing calculaor or graphing sofware GOAL Represen verbal descripions of raes of change using graphs. LEARN ABOUT he Mah Today Seve walked

More information

Interpreting Sinusoidal Functions

Interpreting Sinusoidal Functions 6.3 Inerpreing Sinusoidal Funcions GOAL Relae deails of sinusoidal phenomena o heir graphs. LEARN ABOUT he Mah Two sudens are riding heir bikes. A pebble is suck in he ire of each bike. The wo graphs show

More information

Morningstar Investor Return

Morningstar Investor Return Morningsar Invesor Reurn Morningsar Mehodology Paper March 3, 2009 2009 Morningsar, Inc. All righs reserved. The informaion in his documen is he propery of Morningsar, Inc. Reproducion or ranscripion by

More information

PRESSURE SENSOR TECHNICAL GUIDE INTRODUCTION FEATURES OF ELECTRIC PRESSURE SENSOR. Photoelectric. Sensor. Proximity Sensor. Inductive. Sensor.

PRESSURE SENSOR TECHNICAL GUIDE INTRODUCTION FEATURES OF ELECTRIC PRESSURE SENSOR. Photoelectric. Sensor. Proximity Sensor. Inductive. Sensor. Proximiy INTRDUCTIN Pressur sensor The sensor convers of gases or liquid ino elecrical magniude wih he sensing elemen, and generaes he analog oupu proporional o applied level or he swiching oupu oggled

More information

Pressure Relief Valve Instruction Manual

Pressure Relief Valve Instruction Manual CVR3-M0_062017 Pressure Relief Valve Instruction Manual MODEL: CVR3 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 * Fax: 816-448-2142 E-mail: sales@bvahydraulics.com Website:

More information

KINEMATICS IN ONE DIMENSION

KINEMATICS IN ONE DIMENSION chaper KINEMATICS IN ONE DIMENSION Secion 2.1 Displacemen Secion 2.2 Speed and Velociy 1. A paricle ravels along a curved pah beween wo poins P and Q as shown. The displacemen of he paricle does no depend

More information

POWER DANGER NOW COMMERCIAL. Controls Ba Erodes Slowly to Deliver Lo ACTIVE INGREDIENT: OTHER INGREDIENTS:...32% with Anti-Scale Additive

POWER DANGER NOW COMMERCIAL. Controls Ba Erodes Slowly to Deliver Lo ACTIVE INGREDIENT: OTHER INGREDIENTS:...32% with Anti-Scale Additive 748-275_Leslies Swimming Pool POWER Supplies Power Pro Tabs_20141014_26_748_.pdf P NOW wih Ani-Scale Addiive COMMERCIAL Conrols Ba Erodes Slowly o Deliver Lo KEEP OUT OF REACH OF CHILDREN DANGER Do no

More information

MVS. Electronic fan speed controller for DIN rail. Key features. Article codes Technical specifications. Area of use

MVS. Electronic fan speed controller for DIN rail. Key features. Article codes Technical specifications. Area of use MVS Elecronic fan speed conroller for DIN rail The MVS elecronic speed conrollers conrol he speed of single-phase volage conrollable elecric moors ( VAC / 5 6 z) according o a sandard inpu conrol signal.

More information

INSTALLATION AND USERS GUIDE

INSTALLATION AND USERS GUIDE INSALLAION AND USERS GUIDE BUDDY LIGH - WHIE & COLOR IMPORAN WARNING & SAFEY INSRUCIONS DANGER - SERIOUS BODILY INJURY OR DEAH CAN RESUL IF HESE LIGHS ARE NO INSALLED AND USED CORRECLY DANGER - INSALLERS,

More information

60 farm jack. Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA 93011

60 farm jack. Distributed exclusively by Harbor Freight Tools Mission Oaks Blvd., Camarillo, CA 93011 60 farm jack 66183 Set up And Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read

More information

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment

310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility

More information

Nozzle valve system for the variable atomization of very small liquid volumes

Nozzle valve system for the variable atomization of very small liquid volumes Nozzle valve sysem for he variable aomizaion of very small liquid volumes V E R Y S M A L L L I Q U I D V O L U M E S M A X I M U M B E N E F I T Innovaive spraying echnology opens up new applicaions The

More information

97C COMPRESSOR KIT 12V PART NO C COMPRESSOR KIT 24V PART NO C COMPRESSOR KIT PART NO

97C COMPRESSOR KIT 12V PART NO C COMPRESSOR KIT 24V PART NO C COMPRESSOR KIT PART NO 97C COMPRESSOR KIT 12V PART NO. 00097 97C COMPRESSOR KIT 24V PART NO. 02497 98C COMPRESSOR KIT PART NO. 00098 97C 98C IMPORTANT: It is essential that you and any other operator of this product read and

More information

INSTRUCTIONS FOR USE. This file can only be used to produce a handout master:

INSTRUCTIONS FOR USE. This file can only be used to produce a handout master: INSTRUCTIONS OR USE This file can only be used o produce a handou maser: Use Prin from he ile menu o make a prinou of he es. You may no modify he conens of his file. IMPORTNT NOTICE: You may prin his es

More information

Nozzle valve system for the variable atomization of very small liquid volumes

Nozzle valve system for the variable atomization of very small liquid volumes Nozzle valve sysem for he variable aomizaion of very small liquid volumes VERY SMALL LIQUID VOLUMES MAXIMUM BENEFIT Innovaive spraying echnology opens up new applicaions The pressure o sandardize is increasing

More information

Neighborhood & Community Services Department

Neighborhood & Community Services Department Bren Childers NCS Direcor Telephone: 270.393.3658 Fax: 270.901.3126 Bren.Childers@bgky.org 707 E. Main A PO Box 430 Bowling Green, Kenucky 42102 www.bgky.org January 20, 2017 Dear Propery Owner: Neighborhood

More information

100C Air Compressor Kit

100C Air Compressor Kit 10010 100C Air Compressor (standard mounting bracket, CE Spec) 10014 100C Air Compressor (no leader hose or check valve, CE Spec) 10016 100C Air Compressor (with Omega Bracket, CE Spec) IMPORTANT: It is

More information

MODEL 840 AIR HYDRAULIC PUMP INSTRUCTION

MODEL 840 AIR HYDRAULIC PUMP INSTRUCTION MODEL 840 AIR HYDRAULIC PUMP INSTRUCTION Jackco Transnational Inc. 202 South El Monte, CA 888-452-2526 www.jackco.com FOR YOUR SAFETY Read all instructions, warnings and cautions carefully. Follow all

More information

MODEL NUMBER: PSI AIR SOURCE KIT 200 PSI Compressor on 2.0 Gallon 200 PSI Air Tank

MODEL NUMBER: PSI AIR SOURCE KIT 200 PSI Compressor on 2.0 Gallon 200 PSI Air Tank IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock or Electrocution: MODEL NUMBER: 20008 200 PSI AIR SOURCE KIT 200 PSI Compressor on 2.0 Gallon 200 PSI Air Tank IMPORTANT: It is

More information

200 PSI COMPRESSORS - MODEL NUMBERS

200 PSI COMPRESSORS - MODEL NUMBERS 200 PSI COMPRESSORS - MODEL NUMBERS 380C AIR COMPRESSOR KIT PART NO. 38033 480C AIR COMPRESSOR KIT PART NO. 48043 380C 480C IMPORTANT: It is essential that you and any other operator of this product read

More information

Name Class Date. Step 2: Rearrange the acceleration equation to solve for final speed. a v final v initial v. final v initial v.

Name Class Date. Step 2: Rearrange the acceleration equation to solve for final speed. a v final v initial v. final v initial v. Skills Workshee Mah Skills Acceleraion Afer you sudy each sample problem and soluion, work ou he pracice problems on a separae shee of paper. Wrie your answers in he spaces provided. In 1970, Don Big Daddy

More information

Ministry of Agriculture and Rural Development Animal and Plant Health Regulatory Directorate

Ministry of Agriculture and Rural Development Animal and Plant Health Regulatory Directorate Minisry of Agriculure and Rural Developmen Animal and Plan Healh Regulaory Direcorae Checklis for saus of slaugherhouses for cale, sheep and goas (General informaion) i Addis Ababa Ehiopia 1 1. Background

More information

OPERATOR S MANUAL 1.5 HP/6-GALLON 6 GAL AIR COMPRESSOR IMPORTANT: READ OPERATOR S MANUAL BEFORE USING. Toll Free Helpline:

OPERATOR S MANUAL 1.5 HP/6-GALLON 6 GAL AIR COMPRESSOR IMPORTANT: READ OPERATOR S MANUAL BEFORE USING. Toll Free Helpline: ITEM# 0306 SKU# 07-55 OPERATOR S MANUAL.5 HP/6-GALLON 6 GAL AIR COMPRESSOR IMPORTANT: READ OPERATOR S MANUAL BEFORE USING Toll Free Helpline: -888-899-06 VY03A36669 TABLE OF CONTENTS Specifications------------------------------------------------------------------------------------------------

More information

444C DUAL PERFORMANCE VALUE PACK

444C DUAL PERFORMANCE VALUE PACK (Chrome) PART NO. 44432 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL

More information

AP Physics 1 Per. Unit 2 Homework. s av

AP Physics 1 Per. Unit 2 Homework. s av Name: Dae: AP Physics Per. Uni Homework. A car is driven km wes in hour and hen 7 km eas in hour. Eas is he posiive direcion. a) Wha is he average velociy and average speed of he car in km/hr? x km 3.3km/

More information

420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO

420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO 420C AIR COMPRESSOR KIT PART NO. 42042 460C AIR COMPRESSOR KIT PART NO. 46043 420C 460C IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this

More information

INSTALLATION, OPERATION AND SERVICE MANUAL ABS AIR BAG LIFT

INSTALLATION, OPERATION AND SERVICE MANUAL ABS AIR BAG LIFT INSTALLATION, OPERATION AND SERVICE MANUAL ABS AIR BAG LIFT P.O. Box 1058 1058 West Industrial Avenue Guthrie, OK 73044-1058 405-282-5200 FAX: 405-282-8105 www.autoquip.com Item # 830ABS Version 1.0 07/2001

More information

MODEL NUMBER: M20005 AIR SOURCE KIT. 30% Duty Compressor on. 2.0 Gallon Air Tank SAVE THIS MANUAL FOR FUTURE REFERENCE

MODEL NUMBER: M20005 AIR SOURCE KIT. 30% Duty Compressor on. 2.0 Gallon Air Tank SAVE THIS MANUAL FOR FUTURE REFERENCE MODEL NUMBER: M20005 AIR SOURCE KIT 30% Duty Compressor on 2.0 Gallon Air Tank SAVE THIS MANUAL FOR FUTURE REFERENCE USER MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock

More information

Cylinder Tilt Saddle Instruction Manual

Cylinder Tilt Saddle Instruction Manual Cylinder Tilt Saddle Instruction Manual MODELS: SDT05, SDT10, SDT15, SDT25 SFA Companies 10939 N. Pomona Ave. Kansas City, MO 64153 Tel: 888-332-6419 - Fax: 816-448-2142 E-mail: sales@bvahydraulics.com

More information

Installation and Service Manual

Installation and Service Manual An Actuant Company Installation and Service Manual Heavy Duty Hydraulic Stabilization Legs CONTENTS Part # 3010003129 REV 0D Section Page 1.0 Receiving Instructions 2 2.0 Safety Issues 2 3.0 Hydraulic

More information

Solid-state Timer H3BA-N. Broad Line-up of Series Solid-state Timer with Valuable Multiple-time Ranges and Multiple-operating Modes

Solid-state Timer H3BA-N. Broad Line-up of Series Solid-state Timer with Valuable Multiple-time Ranges and Multiple-operating Modes Solid-sae Timer H3BA-N Please read and undersand his caalog before purchasing he producs. Please consul your OMRON represenaive if you have any quesions or commens. Refer o Warrany and Applicaion Consideraions

More information

SWIMMING POOL HEAT PUMP UNITS. Installation & Instruction Manual DURA - series

SWIMMING POOL HEAT PUMP UNITS. Installation & Instruction Manual DURA - series SWIMMIG POO HEAT PUMP UITS Insallaion & Insrucion Manual DUA - series ev. 1.12 29.07.2014 Conens SWIMMIG POO HEAT PUMP UITS... 1! Conens... 2! 1. Preface... 3! 2. Specificaions... 4! 2.1 Technical daa

More information

AIR/OVER HYDRAULIC JACK 20 TON

AIR/OVER HYDRAULIC JACK 20 TON AIR/OVER HYDRAULIC JACK 0 TON 4487 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 999 by Harbor Freight Tools.

More information

BGW-installation instruction for BGW-anchor with data head

BGW-installation instruction for BGW-anchor with data head BGW-insallaion insrucion for BGW-anchor wih daa head BGW- lifing eye wih swivel for axial and diagonal lif. Grease he hread well. Lifing loop for diagonal lifing unil 45. Screw he loop unil he ground of

More information

INTENDED USE TECHNICAL SPECIFICATIONS

INTENDED USE TECHNICAL SPECIFICATIONS 1/2IN. HEAVY-DUTY AIR IMPACT WRENCH OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result

More information

SPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.

SPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1. 2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or

More information

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock: - Do not disassemble. Do not attempt repairs or modifications. Refer to qualified service agencies for all service and repairs.

More information

4-in-1 Professional Inflator Kit

4-in-1 Professional Inflator Kit 4-in-1 Professional Inflator Kit Owner s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety

More information

ANALYSIS OF RELIABILITY, MAINTENANCE AND RISK BASED INSPECTION OF PRESSURE SAFETY VALVES

ANALYSIS OF RELIABILITY, MAINTENANCE AND RISK BASED INSPECTION OF PRESSURE SAFETY VALVES ANALYSIS OF RELIABILITY, MAINTENANCE AND RISK BASED INSPECTION OF PRESSURE SAFETY VALVES Venilon Forunao Francisco Machado Mechanical Engineering Dep, Insiuo Superior Técnico, Av. Rovisco Pais, 049-00,

More information

AIR COMPRESSOR. Failure to follow all instructions as listed below may result in electrical shock, fire, and/or serious personal injury.

AIR COMPRESSOR. Failure to follow all instructions as listed below may result in electrical shock, fire, and/or serious personal injury. 2 GALLON AIR COMPRESSOR Model: 7517 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials

More information

400C & 450C DUAL PERFORMANCE VALUE PACKS

400C & 450C DUAL PERFORMANCE VALUE PACKS (Chrome) PART NO. 40013 (Silver) PART NO. 45012 (Chrome) PART NO. 45013 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before

More information

42045 Heavy Duty ADA Base Model Kit: 85/105 PSI (ADA Compressor Only) Heavy Duty ADA Base Model Kit: 110/145 PSI (ADA Compressor Only)

42045 Heavy Duty ADA Base Model Kit: 85/105 PSI (ADA Compressor Only) Heavy Duty ADA Base Model Kit: 110/145 PSI (ADA Compressor Only) 42045 Heavy Duty ADA Base Model Kit: 85/105 PSI (ADA Compressor Only) 42047 Heavy Duty ADA Base Model Kit: 110/145 PSI (ADA Compressor Only) 45052 Constant Duty ADA Base Model Kit: 85/105 PSI (ADA Compressor

More information

Operating Instructions for BAIR22-6 AIR-POWERED CRIMPING TOOL

Operating Instructions for BAIR22-6 AIR-POWERED CRIMPING TOOL Operating Instructions for BAIR22-6 AIR-POWERED CRIMPING TOOL Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Table of Contents

More information

Fiber Cable Puller with Tuf-Lugger lite

Fiber Cable Puller with Tuf-Lugger lite 7 OPERATING INSTRUCTION MANUAL Fiber Cable Puller with Tuf-Lugger lite Copyright 2015 DCD Design & Manufacturing Ltd. Revision 1.0 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING The Fiber

More information

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS 18 GAUGE 1-1/4 INCH BRAD NAILER Model: 7611 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.

More information

Control elements. Fine adjustment. Function selector. Status indication. 24 V DC typ. 0,25 W / 0,25 VA. 24 V DC typ. 0,03 W / 0,09 VA. min.

Control elements. Fine adjustment. Function selector. Status indication. 24 V DC typ. 0,25 W / 0,25 VA. 24 V DC typ. 0,03 W / 0,09 VA. min. 4 funcions 10 ime ranges Supply volage 24-240V AC/DC 1 change-over conac Widh 22,5 mm Conrol elemens Fine adjusmen Seing of ime range Funcion selecor Saus indicaion /: Supply volage : elay saus TECHNICAL

More information

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO 250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual

More information

LEWA intellidrive. The mechatronic All-in-One pump system. intelligent flexible dynamic high precision. Foto: ratiopharm

LEWA intellidrive. The mechatronic All-in-One pump system. intelligent flexible dynamic high precision. Foto: ratiopharm The mecharonic All-in-One pump sysem Foo: raiopharm inelligen flexible dynamic high precision For diverse applicaions: a limiless range of poenial uses Phoo: raiopharm Mixing wo media in one pump head:

More information

400H HARDMOUNT AIR COMPRESSOR KIT PART NO H HARDMOUNT AIR COMPRESSOR KIT PART NO

400H HARDMOUNT AIR COMPRESSOR KIT PART NO H HARDMOUNT AIR COMPRESSOR KIT PART NO 400H HARDMOUNT AIR COMPRESSOR KIT PART NO. 40042 450H HARDMOUNT AIR COMPRESSOR KIT PART NO. 45042 400H 450H IMPORTANT: It is essential that you and any other operator of this product read and understand

More information

2 GAL AIR COMPRESSOR OPERATOR S MANUAL 1/3HP/2-GALLON IMPORTANT: READ THIS OPERATOR S MANUAL BEFORE USING

2 GAL AIR COMPRESSOR OPERATOR S MANUAL 1/3HP/2-GALLON IMPORTANT: READ THIS OPERATOR S MANUAL BEFORE USING ITEM# AT01101 SKU# 207-1525 OPERATOR S MANUAL 1/3HP/2-GALLON 2 GAL AIR COMPRESSOR IMPORTANT: READ THIS OPERATOR S MANUAL BEFORE USING Toll Free Helpline: 1-888-899-0146 Versions 01 TABLE OF CONTENTS SAFETY

More information

200 PSI FAST-FILL AIR SOURCE KIT

200 PSI FAST-FILL AIR SOURCE KIT 200 PSI FAST-FILL AIR SOURCE KIT 55% Duty Compressor on 2.0 Gallon Air Tank PART NO. 20007 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of

More information

200 PSI HIGH-FLOW AIR SOURCE KIT

200 PSI HIGH-FLOW AIR SOURCE KIT 200 PSI HIGH-FLOW AIR SOURCE KIT 50% Duty Compressor on 2.0 Gallon Air Tank PART NO. 20008 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of

More information

AC1810 / AC1810-A TECHNICAL SPECIFICATIONS. Operating Pressure psi ( kgs/cm²) [AC1810] Displacement. Net Weight

AC1810 / AC1810-A TECHNICAL SPECIFICATIONS. Operating Pressure psi ( kgs/cm²) [AC1810] Displacement. Net Weight Technical Specifications Operating Instructions Maintenance Information Troubleshooting Guide Parts Diagrams AC1810 / AC1810-A THE EVOLUTION OF PERFECTION CAUTION: Before attempting to use or service this

More information

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS

accidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS 18 GAUGE 2 INCH BRAD NAILER Model: 7555 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.

More information

COMPACT METAL bender 99826

COMPACT METAL bender 99826 COMPACT METAL bender 99826 Set up And Operating Instructions Distributed exclusively by Harbor Freight Tools. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com

More information

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO

250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO 250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual

More information

2000 lb manual winch

2000 lb manual winch 2000 lb manual winch Model 41694 Operation Instructions Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd., Camarillo, CA 93011

More information

Parts & Operators Manual

Parts & Operators Manual Parts & Operators Manual (888) 317-5878 www.talet.ca To The Owner General Comments Congratulations on the purchase of your new Talet Mat Grapple. Your unit was carefully designed and manufactured to give

More information

Q-POWER 106 SERIES HYDRAULIC SQUEEZE CHUTE PRODUCT MANUAL arrowquip.com

Q-POWER 106 SERIES HYDRAULIC SQUEEZE CHUTE PRODUCT MANUAL arrowquip.com Q-POWER 106 SERIES HYDRAULIC SQUEEZE CHUTE PRODUCT MANUAL 1-877-275-6075 cs@arrowquip.com arrowquip.com CONTENTS General Description of the Q-Power 106 Series Hydraulic 1 Squeeze Chute Safety Precautions

More information

1 DRIVE INDUSTRIAL IMPACT WRENCH

1 DRIVE INDUSTRIAL IMPACT WRENCH 1 DRIVE INDUSTRIAL IMPACT WRENCH 92622 ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at http://www.harborfreight.com Copyright 2004 by Harbor Freight

More information

OPERATION INSTRUCTIONS Form 6899-TE, Four-Post Lift Rack. MODELS L451 and L454 (all model variations) Copyright 2014 Hunter Engineering Company

OPERATION INSTRUCTIONS Form 6899-TE, Four-Post Lift Rack. MODELS L451 and L454 (all model variations) Copyright 2014 Hunter Engineering Company OPERATION INSTRUCTIONS Form 6899-TE, 11-14 Four-Post Lift Rack MODELS L451 and L454 (all model variations) Copyright 2014 Hunter Engineering Company Hunter Rack and Jack - Equipment Training Report Hunter

More information

2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL

2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL 2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL Model: 52024 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement,

More information

DIMENSIONS AC Road travel

DIMENSIONS AC Road travel DIMENSIONS AC 10009 Road ravel 04 DIMENSIONS AC 10009 Lifing operaion OUTRIGGER BASES TO CHOOSE FROM: A 13.54m x 13.538m B 12.0m x 12.0m (NEW) C 9.671m x 9.885m 05 HA /SSL (HA50) AC 10009 AC 10009 17 HA

More information

AIR INLINE METAL SHEAR

AIR INLINE METAL SHEAR AIR INLINE METAL SHEAR ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 93011 Copyright 1997 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork

More information