Rice Protein Hydrolyzed

Transcription

1 INCI Name SECTION 1 :: PRODUCT IDENTIFICATION Use of the Substance/Preparation Recommended use of substance/preparation as active ingredient in cosmetics applications Emergency telephone number National Poison Control Center: Tel SECTION 2 :: DATA ON COMPONENTS CAS No. EU No. Chemical / INCI Name % Concentration Water SECTION 3 :: HAZARDS IDENTIFICATION Inhalation No adverse effect expected. Skin Contact No adverse effect expected. Eye Contact May cause mild irritation. Ingestion Excessive ingestion may cause mild nausea or abdominal discomfort. Overexposure No adverse effect expected. This material is generally considered non-toxic.

2 SECTION 4 :: FIRST AID MEASURES General Advice No hazard which requires special first aid measures. Not expected to be a skin or eye irritant (based on available data). Inhalation Move to fresh air. Skin Contact Wash with soap and water. Consult physician if irritation develops or persists. Eye Contact Flush eyes with water and observe. Consult physician if irritation develops or persists. Ingestion Drink plenty of water. Seek medical attention. Overexposure No adverse effect expected. Products of this type have seen safely used in industrial applications for many years (based on available data). SECTION 5 :: FIRE FIGHTING MEASURES Suitable extinguishing media Use water spray, CO2, dry chemical, foam, halon, applied by manufacturer s instructions. Extinguishing media which must not be used for safety reasons No special requirements. Unusual fire and explosion hazards None known Special protective equipment for fire fighters Exercise caution when fighting any chemical fire. Use NIOSH approved self-contained breathing apparatus with full face piece and protective clothing. Specific methods Do not use heavy or direct water stream as it may splash burning liquid. SECTION 6 :: ACCIDENTAL RELEASE MEASURES Personal precautions Ensure adequate ventilation. Use chemical safety goggles and eye / face protection. Environmental precautions Non-Hazardous but avoid direct releases into environment. Methods for clean-up Cover with absorbent material and collect for disposal. Observe all government regulations.

3 SECTION 7 :: HANDLING AND STORAGE Handling Keep working place well ventilated, no special precautions under normal use. Storage Store at room temperature in tightly closed containers. Avoid temperatures above 40C. Do not freeze. Avoid direct sunlight for prolonged periods. Avoid bacterial contamination. SECTION 8 :: EXPOSURE CONTROLS AND PERSONAL PROTECTION Exposure Limit Values No limits established by ACGIH or OSHA. Exposure controls No special precautions under usual conditions of use. Occupational exposure controls No special precautions under usual conditions of use. Ventilation Mechanical ventilation is acceptable. Respiratory Protection None required under usual conditions of use. However, if exposure potential exists, refer to NIOSH Criteria Guides to determine proper equipment. Protective Clothing Normal work gloves and chemical operator s goggles with side splash protection recommended. Other Protective Measures Eye Wash station

4 SECTION 9 :: PHYSICAL AND CHEMICAL PROPERTIES General Information (appearance, odor) Physical State Liquid Color Clear to slightly hazy amber Odor Characteristic Important health safety and environmental information ph Boiling point/range 215 F Flash point > 250F Vapor Pressure (mm-hg) Not determined Vapor Density (AIR=1) Not determined Solubility Water solubility Complete Viscosity Not applicable % Volatile Approximately 76 % Specific Gravity (H2O = 1) 25 C (approx) SECTION 10 :: STABILITY AND REACTIVITY Stability Stable Reactivity Not reactive under normal conditions of use. Incompatibility Concentrated nitric or sulfuric acid, strong oxidizing agents. Conditions to Avoid Gross bacterial contamination. Hazardous Polymerization Will not occur. Hazardous Decomposition Products Burning can produce smoke, CO, CO2, ammonia and other products of incomplete combustion.

5 SECTION 11 :: TOXICOLOGY INFORMATION Not tested on laboratory animals. Acute Toxicity: Oral LD50 anticipated to be greater than 5 g/kg based on available testing data of similar materials. Irritation: HRIPT results of similar materials shows material to be non-irritating. Corrosivity: Non corrosive Sensitization: HRIPT results of similar materials shows material to be non-sensitizing. Carcinogenicity: None of the components are listed as a carcinogen by IARC, NTP, OSHA, ACGIH, or the EU Substance Directive. Mutagenicity: Not expected to present germ cell mutagenicity hazard. Reproductive: Not expected to affect reproduction or development. No data available SECTION 12 :: ECOLOGY INFORMATION SECTION 13 :: DISPOSAL CONSIDERATIONS Dispose of in accordance with all Federal, State and Local regulations for non-hazardous substances. SECTION 14 :: TRANSPORT INFORMATION Not classified as hazardous for transport. HMIS Rating: [4 = Extreme, 3 = High, 2 = Moderate, 1 = Slight, 0 = Insignificant] Health: 0 Flammability: 0 Reactivity: 0 Non-Hazardous SECTION 15 :: REGULATIONS SECTION 16 :: COMMENTS Training advice Read the safety data sheet before using the product. Recommended restrictions None Further information These data are based on our present knowledge. No chemical safety assessment has been carried out for this material by the supplier.

6 DISCLAIMER Technical information and / or suggestions for use including any formulations and / or procedures are believed to be correct. However this does not constitute a guarantee of the accuracy of the information or suggestions contained herein and confirming tests in your own laboratory and / or facility are recommended. No statement or suggestion of use should be construed as a recommendation or inducement to violate any regulations and / or requirements or as warranties (express or implied) of its fitness for any particular use and / or purpose and no liability may be assumed. Prospective purchasers are invited to conduct their own test and studies to determine the fitness of Ingredients To Die For products for their particular purposes and specific applications and confirming the information and all instructions and / or procedures directly is recommended. All purchases of products from Ingredients To Die For should be made with the clear understanding that use of any product is at the sole discretion of the customer and that suitability for purpose is at the sole discretion of the customer and should be used only after careful review and understanding of all supportive documentation. The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. The information contained in this PDF should not be construed as recommending the use of information contained in the PDF in violation of any patent, or as warranties (express or implied) and no patent liability may be assumed. Prospective retailers are invited to conduct their own research to determine compliance for their particular purpose and specific products or legal council is recommended. The information contained in this PDF is obtained from current and reliable sources. As the ordinary or otherwise use(s) of this product and / or information is outside the control of Ingredients To Die For, no representation or warranty (express or implied) is made as to the effect(s) of such use(s) (including damage or injury), or the results obtained. Ingredients To Die For expressly disclaims responsibility as to the ordinary or otherwise use(s). Furthermore, Ingredients To Die For as to the fitness for any use should consider nothing contained herein as a recommendation. The liability of Ingredients To Die For is limited to the value of the goods in case of manufacturer defect and does not include any consequential loss.