Designing an atmosphere controlling hollow fiber membrane system for mango preservation
|
|
- Josephine Johnston
- 5 years ago
- Views:
Transcription
1 Korean J. Chem. Eng., 34(7), (2017) DOI: /s INVITED REVIEW PAPER INVITED REVIEW PAPER pissn: eissn: Designing an atmosphere controlling hollow fiber membrane system for mango preservation Hong Liu, Linxiang Fu, Huan Liu, Caili Zhang, Bing Cao, and Pei Li College of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing , China (Received 14 December 2016 accepted 5 April 2017) Abstract We devised an atmosphere controlling facility to gain a longer life span for mango. A membrane module made of polyethersulfone/polydimethylsiloxane (PES/PDMS) composite membrane was applied to selectively permeate CO 2 from the gas mixture of the fruit container. To design the membrane separation system, two models were introduced into our mathematical simulations: (1) an equilibrium model giving the optimal membrane area, the compositions of CO 2 and O 2 in the fruit container, feed flow rate and pressures on both the feed and permeate sides of the module, and (2) a dynamic model simulating the change in the gas composition of the fruit container with time. The pressure build-up in the bore side of the hollow fiber was also discussed using the Hagen-Poiseuille equation. The best membrane module configuration was obtained based on the pressure build-up analysis. That was (1) the vacuum pressure should be set at 0.1 bar, (2) the hollow fiber inner diameter should be 0.45 mm, and (3) the vacuum should be applied at both ends of the hollow fiber bore sides. Keywords: Membranes, Coatings, Application, Fibers, Separation Techniques INTRODUCTION Mangoes are delicious but if not stored properly they can easily deteriorate. Until now, knowledge about the potential shelf life, quality changes or microbial population of fresh-cut mangos has been limited [1]. To be able to design and operate a van container that can prolong the mango s shelf life, factors such as biological effects of temperature, relative humidity, modified oxygen and carbon dioxide levels need to be controlled precisely [2,3]. In general, exposure to concentrated O 2 alone cannot inhibit microbial growth effectively, while in most cases, high CO 2 concentration may reduce the growth of bacteria to some extent [4]. So it is important to control the gas composition. Currently, there are two main modified atmosphere (MA) implementations being used commercially: (1) controlled atmosphere storage (CAS), and (2) modified atmosphere storage (MAP) [5]. MAP is beneficial for minimally processed products as reported by Amanatidou and others [6-9]. While, CAS is more appropriate and practical for large-scale perishable transport [5,10]. In recent years, energy efficient membrane-based technology has become one of the most important separation processes [11,12]. Compared to other gas separation techniques [13, 14], membrane separation has advantages such as low operation price, high efficiency, and environmental benign [15,16]. Chong et al. [5] designed a membrane-controlled atmosphere storage (MCAS) system. Their work has enlightened us in the designation of the MCAS system for mango reservation. However, since the preferred storage condition for mango is very different from the avocado used in their system, many adjustments have to be made in our designs To whom correspondence should be addressed. lipei@mail.buct.edu.cn Copyright by The Korean Institute of Chemical Engineers. which will be introduced in detail in this work. According to the data given by Ravindra and Goswami, mango should be stored at 13 o C and normal pressure, with a relative humidity of 85-90%, and an gas composition of O 2 at 3-5%, CO 2 at 5-8% and N 2 at 87-92% [17]. Under this condition, the respiration rate of mango is limited to (m 3 /h). In our design, the temperature of the mango reefer is regulated by using a common refrigerator system, while the gas composition is controlled with a membrane-based system. When running the membrane system, certain amount of the gas will pass through the membrane and be discharged to the atmosphere. This will cause a pressure decrease inside the mango reefer. Hence, a pressure balance equipment is installed to maintain a normal pressure inside the mango reefer. The crucial point of designing the membrane system is to precisely remove the CO 2 produced by mango respiration, while at the same time supply O 2 that is required for mango respiration through the pressure balance system. By doing so, a stable gas composition can be obtained. The driving force of a gas separation membrane is the pressure difference between the feed and permeate sides. Note that the relative humidity inside the mango container is 85-90%. Hence, a slightly higher pressure in the membrane feed side will lead to water condensation on the membrane surface, which may swell the membrane material and deteriorate the membrane separation performance. Therefore, to create a driving force, the membrane permeate side has to be vacuumed and the pressure in the feed side is kept at 1 bar. Based on this design, the driving force is less than 1bar, which is relatively small. Hence, we have to select a material with high gas flux to save the membrane area. In this work, PDMS was chosen for its high CO 2 permeability and moderate CO 2 selectivity over N 2 [18-20]. Since PDMS is a rubbery material, its mechanical strength is weak. We have to prepare a porous substrate to provide the mechanical strength to the membrane. Compared 2019
2 2020 H. Liu et al. to other membrane configurations, the hollow fiber membrane offers many advantages [21-24], such as a large effective membrane area per unit volume that will save the space occupied by the membrane module [25]. Therefore, we fabricated a porous hollow fiber membrane using a low-cost material PES with good mechanical and chemical properties, and subsequently, the porous substrate was coated by a very thin PDMS layer that acted as the selective layer. In many studies, polyacrylonitrile (PAN) is selected as the substrate for fabricating PAN/PDMS composite membranes [26, 27]. Here, we chose PES in consideration of its better physical properties such as strength and flexibility compared with PAN [28-30]. Furthermore, PES is a hydrophobic material which makes the PES hollow fiber membrane very stable in humid environment [31,32]. Our objective was to design the required membrane area, hollow fiber module configuration, and operation parameters to meet the best storage condition for mango. To realize this purpose, we developed two models. Through the equilibrium model, we calculated the membrane area and the parameters that fitted the requirement. Using the dynamic model, we simulated the changes in the gas compositions with time. At the end, we discussed the pressure build-up in the bore side and figured out the best membrane module configuration. MODEL DEVELOPMENT 1. Mathematical Model for Gas Separation It is essential to figure out the effects of operation parameters on the performance of the membrane module [33,34]; thus, developing a mathematical model for estimating the membrane performance is necessary to design the system. Actually, there are four idealized flow patterns for operation of a membrane gas separation module [5]. Bore side feed may encounter significant pressure buildup along the hollow fiber membrane due to the small dimension of the membrane bore side and high feed flux. While in the shell side feed mode, the pressure build-up of the feed gas is trivial since the hydrodynamic radius of the membrane module is much greater than that of the hollow fiber bore side. Hence, we chose the co-current flow mode, shell side feed hollow fiber permeator and ignored the pressure build-up in the shell side. To simplify the model, we assumed a constant gas composition in the feed side. In this case, there was no difference between the co-current flow and the counter-current flow modes. Wang et al. [35] built a model to characterize the separation performance of hollow fiber membrane that separated a binary gas mixture. They also studied the effects of pressure drop, concentration polarization and non-ideal gas behavior for binary gas separations. We used their model to analyze the separation performance of our hollow fiber module for separating a CO 2, O 2 and N 2 ternary gas mixture. 2. Equilibrium Model To build an equilibrium model, we considered the system already reached steady state with a preferred gas composition. That meant the concentrations of O 2 and CO 2 both reached 5%, respectively. To maintain a normal pressure inside the container, the gas flowing back to the container included two parts: retentate flow from membrane module, and supplementary gas from the pressure balance system. The composition of the supplementary gas was O 2 21%, N 2 79%, and CO 2 0%, which was equal to the typical air composition. And the overall composition of the two flows was supposed to be O 2 5%, CO 2 5%, and N 2 90% to maintain the preferred gas composition inside the container. Since it was difficult to directly calculate the membrane area and operation parameters to maintain both the concentrations of O 2 and CO 2, we first targeted to control the CO 2 concentration inside the container. Based on the modeling results, a series of solutions of which a specific membrane area with operational parameters could meet the requirement of controlling the CO 2 concentration were obtained. Then, we tested the relative O 2 concentration of each solution and picked the solutions that could satisfy the concentration requirements of both gases. The key points were (1) the CO 2 generated by the mango needed to be discharged by the membrane, (2) the O 2 consumed by the mango which was the same amount as the produced CO 2 needed to be supplied by the outside atmosphere, and (3) the above two processes took place at the same moment. Therefore, the CO 2 permeate rate (Q p1 ) was the same as the CO 2 generation rate, which was the mango s respiration rate. Then we could calculate the membrane area and feed flow rate (Q f ) through the equilibrium model, but those results only met the requirement of CO 2 removal. To maintain the concentration of O 2, we had to consider the permeate flow and the supplementary air at the same time, and made an optimal choice from the results we obtained to meet the concentration requirements for both gases. Jin et al. [36] analyzed the effect of stage cut on the separation performance of a binary gas system, but did not apply the model to ternary gas systems. Chong et al. [5] developed a mathematical model for ternary gas separation, and we utilized a similar method to build our mathematical model. In this model, stage cut, which is defined as the ratio of the overall permeate flow rate to the overall feed flow rate, was emphasized. The mathematical model of the separation of multicomponent gas by a hollow fiber membrane module is relatively complicated. So, we made several assumptions to simplify the process for ternary gas separation: (1) Steady state operation, (2) Ignoring the pressure build-up in the shell side and bore side, (3) Ignoring the concentration polarization. And several equations used to describe this model are given as follows: The overall mass balance is given by Eq. (1): Q f =Q r +Q p (1) where Q f is the feed flow rate (m 3 /h), Q r the retentate flow rate (m 3 / h), and Q p the permeate flow rate (m 3 /h). The overall mass balance for single component of the gas mixture is described in Eq. (2): Q f x fi =Q r x ri +Q p y pi (2) where i represents different component (1=CO 2, 2=O 2, 3=N 2 ). In a membrane separation process, the faster permeating species are concentrated in the permeate side, while the slower permeate are concentrated in the retentate. The stage cut (θ) is defined as Eq. (3): Q p Q f θ = (3) July, 2017
3 Designing an atmosphere controlling hollow fiber membrane system for mango preservation 2021 Substituting Eq. (3) into Eq. (2) gives Eq. (4): x ri = x θy fi pi 1 θ where i represents different component (1=CO 2, 2=O 2, 3=N 2 ). The basic mass transfer equation of the gas membrane is: Q pi = AP i P where P i refers to the permeance (cm 3 (STP)/(cm 2 s bar)) of the specified component P refers to the pressure difference (bar), so the permeation rates of the gas can be described as Eq. (5): Q pi =Q p y pi =AP i (P H x ri P L y pi ) (5) P H and P L represent for the pressure at retentate and permeate sides, respectively (bar). And the mole fraction of gas i in permeate flow is given by Eq. (6): y pi = (6) Q p1 + Q p2 + Q p3 To cut down the unknown parameters, the permeation rate of N 2 is expressed by the parameters of O 2 and CO 2 as described in Eq. (7): Q p3 =Q p (1 y p1 y p2 )=AP 3 [P H (1 x r1 x r2 ) P L (1 y p1 y p2 )] (7) Then, by substituting different components (1 and 2) in Eq. (4) and (5) into Eq. (6), we get two quadratic Eqs. (8) and (9). a 1 y 2 p1+b 1 y p1 +c 1 =0 (8) a 2 y 2 p2+b 2 y p2 +c 2 =0 (9) where Q pi a 1 =(P 3 P 1 )[r(1 θ)+θ], a 2 =(P 3 P 2 )[r(1 θ)+θ]; b 1 =P 1 [x f1 +r(1 θ)+θ]+p 2 [x f2 y p2 r(1 θ) y p2 θ] b 1 =+P 3 [(1 r)(1 θ) x f1 x f2 +y p2 θ+y p2 r(1 θ)] b 2 =P 1 [x f1 y p1 r(1 θ) y p1 θ]+p 2 [x f2 +r(1 θ)+θ] b 2 =+P 3 [(1 r)(1 θ) x f1 x f2 +y p1 θ+y p1 r(1 θ)] c 1 = P 1 x f1, c 2 = P 2 x f2 P i (i=1, 2, 3) represents pure gas flux (listed in Table 1) in units of GPU for the PES/PDMS hollow fiber membrane. We set CO 2 concentration, x f1, and O 2 concentration, x f2 to be 5%. Eqs. (8) and (9) can be solved by Newton s iteration method by giving reasonable values of θ, pressure ratio r (r=p L /P H ) and the composition of feed flow, and the result shows the composition of permeate side including y p1, y p2, and y p3. We set the different values of θ from , and pressure ratio r from 0.1 to 0.2. If one of them is fixed, we could obtain a series of results by varying the other parameters. Note that all results meet the requirement of removal CO 2 generated by mango respiration. By solving Eqs. (8) and (9), Table 1. Pure gas permeance of the PES/PDMS hollow fiber membrane (estimated) Pure gas Permeance (GPU) CO 2 O 2 N 2 1 GPU=10 6 cm 3 (STP)/(cm 2 s cm Hg) (4) we get y p1 and y p2, the mole fraction of CO 2 and O 2 in permeate flow. Then we can further determine the mole fractions of CO 2 and O 2 in the retentate flow x r1, x r2 using Eq. (4). Furthermore, by inputting all the values to Eq. (5), the membrane area that meets the requirement to maintain the concentration of CO 2 is acquired. Values of Q p and Q f are determined by using Eqs. (6) and (3), respectively. The overall O 2 concentration of the flow back to the container is estimated by using Eq. (10): Q f x f2 =Q r x r2 +Q p y p2 +Q sp y sp2 (10) where Q sp represents the supplied air flow rate; the concentration of O 2, y sp2 is a constant value of Thus, we can calculate the concentration of O 2 when the system reaches equilibrium. 3. Dynamic Model We have already obtained a number of solutions, each of which includes membrane area and operational parameters. However, when a solution with fixed membrane area A, Q f, and r is applied to a system of which the gas composition is not at the equilibrium stage, the stage cut (θ) will change with time. Thus, we introduce a dynamic model to analyze this process. The dynamic model assumes that within a short time interval, Δt, which in our module is one hour, the composition of the gas inside the container is regarded as a constant. That is, within one hour, the system fits the equilibrium model assumption. Then, the whole gas separation process can be divided into many ideal periods (Δt) that fit the description. And if we accumulate those periods, the relation of gas composition with time is obtained. Specifically, when the membrane area (A), feed flow rate (Q f ) and pressure ratio (r) were settled, the parameters of the first period were expressed as θ 1', Q p 1', y p1 1', y p2 1'. To calculate the values of stage cut and gas composition of the first period, we set a guess value of initial stage cut θ1 0, and the compositions x f1 1 0, x f2 1 0 in the feed were the same as the initial concentrations of O 2, and CO 2 inside the container. Hence, we could calculate y p1 1 0, y p2 1 0 in this period through Eqs. (7), and (8), and subsequently obtained Q p 1 0 by substituting y p1 1 0 or y p2 1 0 into Eqs. (4) and (5). Then, a new value of stage cut θ1 1 could be calculated since θ1 1 =Q p 1 0 /Q f. Substituting θ1 1 into Eqs. (7), and (8) gave a set of new values for y p1 1 1, y p2 1 1 which could be used to calculate θ1 2 through the same calculation procedure. Repeating this process till θ1 n =θ1 n+1, the convergent stage cut θ1' was obtained and the corresponding values of Q p 1 ', y p1 1 ', and y p2 1 ' were applied to calculate the gas composition inside the container (x f1 1 1, x f2 1 1 ) by using Eq. (11). x fi n+1 =x fi n +(r i +Q sp x spi Q p y pi )Δt/V (n=0, 1, 2, 3 ) (11) where i represents different components (1=CO 2, 2=O 2, 3=N 2 ). These two values (x f1 1 1 and x f2 1 1 ) were used to calculate the stage cut and other parameters for the next operation period. By repeating this method for certain periods, the changes in the gas composition inside the container with time were acquired. PRESSURE BUILD-UP IN THE MEMBRANE BORE SIDE In the above models, we assumed negligible pressure build-ups in both membrane shell and bore sides. However, the diameter of Korean J. Chem. Eng.(Vol. 34, No. 7)
4 2022 H. Liu et al. Fig. 1. Hollow fiber membrane module configurations: (a) one side out and one side sealed; (b) two-side out. hollow fiber membrane was so small that the pressure build-up in bore side was not trivial and would lead to insufficient driving force for the membrane module to be able to remove all CO 2 [37]. As shown in Fig. 1, we analyzed two membrane configurations which were one-side out and one side sealed module (Fig. 1(a)) and two-side out module (Fig. 1(b)). To simplify the calculations, we made several assumptions: (1) the pressure build-up in the fiber bore side followed Hagen-Poiseuille equation for compressible fluid; (2) negligible concentration polarization in both the fiber shell and bore sides; and (3) negligible pressure build-up in the fiber shell side. 1. Basic Equations The Hagen-Poiseuille equation for compressible fluid was used to describe the pressure build-up in the bore side of a hollow fiber as shown in Eq. (12): dp l 8μRTq = p (12) dz πp l r 4 i N where P l is the pressure of the sealed side, r i the fiber inner radius (m), T the operating temperature (K), Z the length along the permeator, R the gas constant, and μ the gas viscosity (bar s). We used Eq. (13) for calculating the permeate flowrate: q p =p g πd(p' P l )NZ (13) where P' refers to the pressure of the feed gas (kept at 1 bar). We substituted Eq. (13) into Eq. (12), and set the boundary conditions as: at Z=0, Pl=P1, (P1 corresponding to the highest pressure in the hollow fiber module). Then it gives the following Eq. (14): P l P 2 + P'In P' P l 8μRTP = g Z 2 (14) P' P 4 2 r i If the length of the module and the vacuum pressure are known, we can calculate the pressure distribution along the fiber. After that, using Eq. (13), we can estimate the number of hollow fibers in the membrane module. Based on this method, the pressure build-up for both one-side out and two-side out hollow fiber modules were analyzed. RESULTS AND DISCUSSIONS 1. The Effects of Stage Cut and Permeate Side Pressure on the O 2 Concentration in the Mango Container According to our equilibrium model, the membrane area and Fig. 2. Calculated concentration of O 2 inside the reefer changes with stage cut under different pressure. operation parameters are calculated to meet the requirement for removing all CO 2. Then the resulting O 2 concentration (x f2 ) inside the mango container is estimated using Eq. (10). Obviously, we have to make sure that the concentration of O 2 (x f2 ) stays in the target range (3-5%). During the calculation process, we obtained a series of data including the membrane area and concentration of O 2 back to container by changing the values of θ and/or pressure ratio r. The results are shown in Fig. 2 and Fig. 3. Fig. 2 shows that the O 2 concentration can be controlled below 5% only when the stage cut is lower than 0.2. And the lower the pressure of the permeate side, the smaller the O 2 concentration can be got inside the container. Under the same permeate pressure, the concentration of O 2 increases with the stage cut. It is because a higher stage cut indicates more N 2 permeate through the membrane with CO 2. When this happens, more supplied gas is required to balance the pressure inside the container. Since the O 2 concentration in supplied gas is 0.21, which is much higher than the O 2 concentration inside the container (5%), it will lead to an increase in the O 2 concentration. Under the same stage cut, the concentration of O 2 increases with the permeate pressure. This can be explained by the changes in the membrane driving forces. As the permeate pressure increases from 0.1 bar to 0.2 bar, the driving July, 2017
5 Designing an atmosphere controlling hollow fiber membrane system for mango preservation 2023 Fig. 3. The changes of membrane area with stage cut under different permeate pressures. force for CO 2 is greatly reduced since the mole fraction of CO 2 in the feed side is only 5%. But this effect is relatively mild for N 2 since the mole fraction of N 2 is 90%. Hence, more N 2 will transport to membrane permeate side if same amount of CO 2 needs to be separated. It will again lead to a greater amount of O 2 enriched supplied gas being introduced to the container and increasing the O 2 concentration. Fig. 3 shows that the membrane area decreases as the stage cut and/or the permeate pressure is reduced. As the stage cut decreases, the feed flow rate increases. Hence, the CO 2 concentration in the feed is high, which leads to a greater CO 2 driving force. And less membrane area is required to remove all CO 2. When the permeate side pressure is reduced, the driving force for CO 2 increases significantly. Therefore, the demanded membrane area is decreased. 2. The Effect of Permeate Side Pressure on the Membrane Module Parameters In this study, the membrane driving force can only be enhanced by applying a higher vacuum on the permeate side to avoid water condensation on the membrane feed side. However, a pressure infinitely approaching absolute vacuum is costly in practice. In industrial applications, the applicable vacuum range is from bar [38]. Therefore, we preset the permeate side pressures at 0.1 bar and 0.2 bar, respectively, to estimate the values of the rest of membrane module parameters and analyze the pressure impacts. Table 2 lists the parameters of two membrane modules. Both two modules fulfill the requirements since both CO 2 and O 2 concentrations are well controlled at 5%. Only the permeate side pressures are preset, other parameters including stage cut, feed flow rate, permeate flow rate, and membrane area are obtained by model simulation to achieve the stabilized O 2 and CO 2 concentrations of 5%. An interesting observation is that the membrane areas and permeate flow rates of the two membrane modules are very similar. The main differences between these two designs lie in the feed flow rate and stage cut. Membranes with a higher permeate side pressure need a greater feed flow rate. Note that the key of the design is to control the O 2 concentration as well as the CO 2 concentration. Since the supplied gas flow rate should be equal to the permeate gas flow rate, the same permeate flow rate of the two membrane modules has to be realized to control the same O 2 concentration of the mango container. Therefore, as the permeate flow rate is fixed, a higher feed flow rate is required when membrane module is operated with a higher permeate side pressure. Because with a high feed flow rate, the CO 2 partial pressure in the feed is higher, since less amount of CO 2 is passing through the membrane. And the increase in the CO 2 concentration in the feed will comprise the increase in the permeate side pressure so that maintain the CO 2 driving force of the membrane. 3. Dynamic Simulation Fig. 4 shows the changes in the gas concentrations inside the mango container with time using membrane module one and two whose parameters are listed in Table 2. When the initial composition of the gas inside the container was N 2 78%, O 2 21%, CO 2 0.1%, the preferred gas composition (O 2 =5%, CO 2 =5%) could be realized after running the membrane system for 60 hours at both two permeate pressures. As can be seen, when membrane permeate pressure is lower (0.1 bar), the feed flow rate is significantly reduced, which may save energy for the feed gas blower. Fig. 5 shows the changes in the gas composition in an airtight mango container system. It is obvious that the concentration of O 2 drops significantly without air control system, and after 33 hours the O 2 is depleted. Under this situation, the mango will undergo anaerobic respiration and produce lactic acid, which makes the mango flavor become sour and distasteful. Therefore, an atmosphere controlling system is necessary. Table 2. Parameters of two membrane modules Module parameters Module one Module two Pressure of permeate side (P L /bar) Stage cut θ (at equilibrium) CO 2 mole fraction (at equilibrium) Flow rate feed to membrane (m 3 /h) Permeate flow rate (m 3 /h) Membrane area (m 2 ) O 2 mole fraction (at equilibrium) Outer diameter of the fiber (mm) Number of fiber (one end outlet and one end sealed) Korean J. Chem. Eng.(Vol. 34, No. 7)
6 2024 H. Liu et al. Fig. 4. Changes in the O 2 and CO 2 concentrations of the container with time under different permeate pressures (initial concentrations: O 2 = 0.21, CO 2 =0.01). Fig. 5. The gas composition changes with time in an airtight container without the membrane separation system. 4. Effects of Hollow Fiber Dimensions on Pressure Build-up in the Fiber Bore Side Table 3 lists the dimensions of the PES/PDMS hollow fiber membranes. Since the inner diameters of hollow fiber membranes are relatively small, the pressure build-up along the hollow fiber bore sides cannot be ignored. Therefore, the pressure distribution inside the hollow fiber bore side is estimated by using the Hagen-Poiseuille equation and shown in Fig. 6. For the module with one side out and one side sealed configuration, when the inner diameter of fiber decreases, the pressure build-up increases. The largest increases in the hollow fiber bore sides are obtained at the sealed end of the hollow fibers, which are 0.12, 0.15, and 0.20 bar, respectively, corresponding to the hollow fiber inner diameters of 0.45, 0.40, and 0.35 mm, respectively, as shown in Fig. 6(a). Similar results are shown in Fig. 6(b) of which the pressure build-up is 0.07, 0.10, and 0.13 bar for fiber inner diameters of 0.45, 0.40, and 0.35 mm, respectively. Therefore, a larger fiber inner diameter results in less pressure buildup. An interesting phenomenon was observed: as the permeate side pressure increased from 0.1 to 0.2 bar, the pressure build-up was greatly reduced. This can be explained according to Eq. (12) and Table 2. When the permeate pressure increases to 0.2 bar, the number of fibers increases from 3445 to More hollow fibers result in less gas flow rate of each hollow fiber, which leads to small pressure build-up. In addition, based on Eq. (12), as the vacuum pressure increases to 0.2 bar, the denominator in the right side increases and hence dp l /dz decreases, which means the pressure build-up decreases. Since the pressure build-up at the fiber bore side is large, this Table 3. Dimensions of the hollow fiber composite membranes Membrane material Polyethersulfone/polydimethylsiloxane Inner diameter of fiber 0.35 mm/0.40 mm/0.45 mm Outer diameter of fiber 0.65 mm/0.70 mm/0.66 mm Number of fibers Membrane effective length 1.0 m Stage cut 0.1 to 0.5 Temperature K (13 o C) Mixed gas Oxygen/carbon dioxide/nitrogen 5/5/90 Upstream pressure 1 bar Downstream pressure 0.1 bar or 0.2 bar July, 2017
7 Designing an atmosphere controlling hollow fiber membrane system for mango preservation 2025 Fig. 6. Effect of hollow fiber length (L) on pressure build-up (the hollow fiber module is one end outlet and one end sealed) (a) P 2 =0.1 bar (b) P 2 =0.2 bar. Fig. 7. Pressure distributions for two-side out hollow fiber module: (a) The vacuum pressure is 0.1 bar; and (b) the vacuum pressure is 0.2 bar. seriously reduces the membrane driving force. The two-sides out configuration should be adopted because this design reduces the path length of the permeate gas by half. Fig. 7 shows the pressure distributions of the two-side out hollow fiber membranes. As can be seen, the biggest pressure build-up is located in the middle of the hollow fiber membrane, which is only half of the value of the one-side out configuration. With this design, the average pressure in the bore side is 0.12 bar when hollow fiber membrane has an inner diameter of 0.45 mm and the pressure of the vacuum pump is 0.1bar. In this case, the driving force should be very similar to the designed value. Therefore, the best hollow fiber module design is: (1) 0.1 bar of the vacuum pressure, (2) 0.45 mm of the hollow fiber inner diameter, and (3) two-side out of the hollow fiber bore side. CONCLUSIONS We have developed a mathematical model to describe membrane separation for a ternary mixed gas system and applied it in a membrane based atmospheric controlling system. The pressure ratio of the membrane upstream to downstream, stage cut and membrane area that met the requirements for maintaining the preferred gas compositions in the mango container were obtained. A dynamic model was also established to analyze the changes in the gas composition with time inside the container. The best hollow fiber configuration was obtained after analyzing the pressure build-up at the hollow fiber bore side using the Hagen-Poiseuille equation for compressible fluid. ACKNOWLEDGEMENTS The authors would like to thank the National Natural Science Foundation of China (contract grant number ), the State Key Laboratory of Organic-Inorganic Composites of Beijing University of Chemical Technology (contract grant number ), and the Fundamental Research Funds for the Central Universities (contract grant number buctrc201415) for funding this study. NOMENCLATURE A :membrane area [m 2 ] P i : pure gas permeabilities of gas i [m 3 (STP)/(m 2 s bar)] P H, P L : pressure at retentate and permeate sides, respectively [bar] Q f : feed flow rate to membrane module [m 3 /h] Korean J. Chem. Eng.(Vol. 34, No. 7)
8 2026 H. Liu et al. Q sp Q s Q p Q r : flowrate of gas feed back to the reefer [m 3 /h] : sweep flowrate from membrane module [m 3 /h] : permeate flowrate from membrane module [m 3 /h] : retentate flowrate from membrane module [m 3 /h] r :pressure ratio, P L /P H R i : generation rate of gas i [m 3 /h] V : volume of the reefer [m 3 ] x i : mole fraction of gas i in the reefer x fi : mole fraction of gas i in feed to membrane module x spi : mole fraction of gas i in gas feed back to the reefer x si : mole fraction of gas i in sweep flow x ri : mole fraction of gas i in retentate flow y pi : mole fraction of gas i in permeate flow Δt :time interval [h] R : gas constant, [bar m 3 /(m 3 (STP)K)] Z : length of the module [m] N : number of the hollow fiber : inner diameter of the hollow fiber [m] r i Greek Letters θ :stage cut, Q P /Q f viscosity of the gas, [bar h] REFERENCES 1. N. Rattanapanone, Y. Lee, T. X. Wu and A. E. Watada, Hortscience., 36, 1091 (2001). 2. J. M. Harvey, Int. J. Refrig., 4, 293 (1981). 3. J. Poubol and H. Izumi, J. Food Sci., 70, M69 (2005). 4. A. Amanatidou, E. J. Smid and L. G. M. Gorris, J. Appl. Microbiol., 86, 429 (1999). 5. K. L.Chong, N. Peng, H. Yin, G. G. Lipscomb and T.-S. Chung, J. Food Eng., 114, 61 (2013). 6. M. Martínez-Ferrer, C. Harper, F. Pérez-Muntoz and M. Chaparro, J. Food Sci., 67, 3365 (2002). 7. R. F. Artés, Villaescusa and J. A. Tudela, J. Food Sci., 65, 1112 (2000). 8. A. Amanatidou, R. A. Slump, L. G. M. Gorris and E. J. Smid, J. Food Sci., 65, 61 (2000). 9. K. Tano, J. Arul, G. Doyon and F. Castaigne, J. Food Sci., 64, 1073 (1999). 10. S. C. Fonseca, F. A. Oliveira and J. K. Brecht, J. Food Eng., 52, 99 (2002). 11. P. Bernardo, E. Drioli and G. Golemme, Ind. Eng. Chem. Res., 48, 4638 (2009). 12. M. Binns, S.-Y. Oh, D.-H. Kwak and J.-K. Kim, Korean J. Chem. Eng., 32, 383 (2015). 13.K.K. Sirkar, Chem. Eng. Sci., 32, 1137 (1977). 14. S. Alexander Stern, J. Membr. Sci., 94, 1 (1994). 15.F. Ahmad, K.K. Lau, S.S.M. Lock, S. Rafiq, A.U. Khan and M. Lee, J. Ind. Eng. Chem. (Amsterdam, Neth.), 21, 1246 (2015). 16. S. S. Hosseini, J. A. Dehkordi and P. K. Kundu, Korean J. Chem. Eng., 33, 3085 (2016). 17. M. R.Ravindra and T. K.Goswami, Biosyst. Eng., 99, 239 (2008). 18. F. W. Wu, L. Li, Z. H. Xu, S. J. Tan and Z. B. Zhang, Chem. Eng. J. (Amsterdam, Neth.), 117, 51 (2006). 19. T. Hu, G. X. Dong, H. Y. Li and V. Chen, J. Membr. Sci., 432, 13 (2013). 20. D. Sun, P. Yang, L. Lin, H.-H. Yang and B.-B. Li, Korean J. Chem. Eng., 31, 1877 (2014). 21. R. Khalilpour, A. Abbas, Z. Lai and I. Pinnau, Chem. Eng. Res. Des., 91, 332 (2013). 22.F. Ahmad, K.K. Lau, A.M. Shariff and Y. Fong Yeong, J. Membr. Sci., 430, 44 (2013). 23. P. Li and M. R. Coleman., Eur. Polym. J., 49, 482 (2013). 24. P. Li, T. S. Chung and D. R. Paul, J. Membr. Sci., 450, 380 (2014). 25. N. Peng, N. Widjojo, P. Sukitpaneenit, M. M. Teoh, G. G. Lipscomb, T.-S. Chung and J.-Y. Lai, Prog. Polym. Sci., 37, 1401 (2012). 26. P. Li, H. Z. Chen and T.-S. Chung, J. Membr. Sci., 434,18 (2013). 27. H. Z. Chen, Z. Thong, P. Li and T.-S. Chung, Int. J. Hydrogen. Energy, 39, 5043 (2014). 28. S. S. Madaeni, E. Enayati and V. Vatanpour, J. Appl. Polym. Sci., 122, 827 (2011). 29. G. Bakeri, M. Rezaei-DashtArzhandi, A. F. Ismail, T. Matsuura, M.S. Abdullah and N.B. Cheer, Korean J. Chem. Eng., 34, 160 (2017). 30. M. S. Muhamad, M. R. Salim and W. J. Lau, Korean J. Chem. Eng., 32, 2319 (2015). 31. M. Sadrzadeh, M. Amirilargani, K. Shahidi and T. Mohammadi, J. Membr. Sci., 342, 236 (2009). 32. S. A. Sonalkar, P. J. Hao and G. G. Lipscomb, Ind. Eng. Chem. Res. Res., 49, (2010). 33. V. S. Kovvali, K. R. Krovvidi and A. A. Khan, J. Membr. Sci., 73, 1 (1992). 34.P.J. Hao, J.G. Wijmans, J. Kniep and R.W. Baker, J. Membr. Sci., 462, 131 (2014). 35. R. Wang, S. L. Liu, T. T. Lin and T. S. Chung, Chem. Eng. Sci., 57, 967 (2002). 36. H. G. Jin, S. H. Han, Y. M. Lee and Y. K. Yeo, Korean J. Chem. Eng., 28, 41 (2011). 37. P. Shao and R. Y. M. Huang, J. Membr. Sci., 271, 69 (2006). 38. T. C. Merkel, H. Q. Lin, X. T. Wei and R. Baker, J. Membr. Sci., 359, 126 (2010). July, 2017
LOW PRESSURE EFFUSION OF GASES revised by Igor Bolotin 03/05/12
LOW PRESSURE EFFUSION OF GASES revised by Igor Bolotin 03/05/ This experiment will introduce you to the kinetic properties of low-pressure gases. You will make observations on the rates with which selected
LOW PRESSURE EFFUSION OF GASES adapted by Luke Hanley and Mike Trenary
ADH 1/7/014 LOW PRESSURE EFFUSION OF GASES adapted by Luke Hanley and Mike Trenary This experiment will introduce you to the kinetic properties of low-pressure gases. You will make observations on the
Separation of N 2 /SF 6 binary mixtures using polyethersulfone (PESf) hollow fiber membrane
Korean J. Chem. Eng., 9(8), 1081-1085 (01) DOI: 10.1007/s11814-011-094-z INVITED REVIEW PAPER Separation of binary mixtures using polyethersulfone (PESf) hollow fiber membrane Dae-Hoon Kim*, Yong-Hae Ko**,
Experimental Research on Oxygen-enriched Air Supply System for Gasoline Engine
Sensors & Transducers 013 by IFSA http://www.sensorsportal.com Experimental Research on Oxygen-enriched Air Supply System for Gasoline Engine 1, Yahong Li, 3 Lixi Zhang, 1 Zelu Sun 1 School of Chemistry
Fall 2004 Homework Problem Set 9 Due Wednesday, November 24, at start of class
0.30 Fall 004 Homework Problem Set 9 Due Wednesday, November 4, at start of class Part A. Consider an iron surface which serves as a catalyst for the production of ammonia from nitrogen and hydrogen. The
Preparation and Gas Separation Properties of Asymmetric Polysulfone Membranes by a Dual Bath Method
Korean J. Chem. Eng., 17(2), 143-148 (2000) Preparation and Gas Separation Properties of Asymmetric Polysulfone Membranes by a Dual Bath Method Wan-Jin Lee, Deuk-San Kim and Jin-Hwan Kim* Faculty of Applied
Chapter 13 Gases, Vapors, Liquids, and Solids
Chapter 13 Gases, Vapors, Liquids, and Solids Property is meaning any measurable characteristic of a substance, such as pressure, volume, or temperature, or a characteristic that can be calculated or deduced,
SPE Copyright 2001, Society of Petroleum Engineers Inc.
SPE 67232 Sampling Volatile Oil Wells Ahmed H. El-Banbi, SPE, Cairo University/Schlumberger Holditch-Reservoir Technologies, and William D. McCain, Jr., SPE, Texas A&M University Copyright 2001, Society
Optimizing Compressed Air Storage for Energy Efficiency
University of Dayton ecommons Mechanical and Aerospace Engineering Faculty Publications Department of Mechanical and Aerospace Engineering 4-2011 Optimizing Compressed Air Storage for Energy Efficiency
Figure Vapor-liquid equilibrium for a binary mixture. The dashed lines show the equilibrium compositions.
Another way to view this problem is to say that the final volume contains V m 3 of alcohol at 5.93 kpa and 20 C V m 3 of air at 94.07 kpa and 20 C V m 3 of air plus alcohol at 100 kpa and 20 C Thus, the
maintaining storage tank dissolved oxygen levels utilizing gas transfer membranes
Water Technologies & Solutions technical paper maintaining storage tank dissolved oxygen levels utilizing gas transfer membranes Authors: W.E. Haas, SUEZ, J. Helmrich, Florida Power and Light and J.E.
Lab 3 Introduction to Quantitative Analysis: Pumps and Measurements of Flow
Georgia Institute of Technology School of Earth and Atmospheric Sciences EAS 4641, Spring 2008 Lab 3 Introduction to Quantitative Analysis: Pumps and Measurements of Flow Purpose of Lab 3: 1) To gain a
Chem 110 General Principles of Chemistry
CHEM110 Worksheet - Gases Chem 110 General Principles of Chemistry Chapter 9 Gases (pages 337-373) In this chapter we - first contrast gases with liquids and solids and then discuss gas pressure. - review
Influencing Factors Study of the Variable Speed Scroll Compressor with EVI Technology
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2016 Influencing Factors Study of the Variable Speed Scroll Compressor with EVI Technology
Supporting Information
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry A. This journal is The Royal Society of Chemistry 2017 Supporting Information Metal-organic framework-derived CoSe2/(NiCo)Se2
Characterizers for control loops
Characterizers for control loops By: F. G. Shinskey (May 1999) Introduction Commercial controllers such as the PID series (proportional, integral, derivative, and their combinations) are linear devices
CFD SIMULATIONS OF GAS DISPERSION IN VENTILATED ROOMS
CFD SIMULATIONS OF GAS DISPERSION IN VENTILATED ROOMS T. Gélain, C. Prévost Institut de Radioprotection et de Sûreté Nucléaire (IRSN), Saclay, France Abstract In order to better understand the risks due
Figure 1 Schematic of opposing air bearing concept
Theoretical Analysis of Opposing Air Bearing Concept This concept utilizes air bearings to constrain five degrees of freedom of the optic as shown in the figure below. Three pairs of inherently compensated
Operating Guidelines for PermSelect Modules Liquid Contacting
Operating Guidelines for PermSelect Modules Liquid Contacting PermSelect PDMSXA-2500 (0.25m 2 ) PermSelect PDMSXA-7500 (0.75m 2 ) PermSelect PDMSXA-1.0 (1m 2 ) PermSelect PDMSXA-2.1 (2.1m 2 ) PermSelect
Journal of Chemical and Pharmaceutical Research, 2016, 8(6): Research Article. Walking Robot Stability Based on Inverted Pendulum Model
Available online www.jocpr.com Journal of Chemical and Pharmaceutical Research, 2016, 8(6):463-467 Research Article ISSN : 0975-7384 CODEN(USA) : JCPRC5 Walking Robot Stability Based on Inverted Pendulum
PURE SUBSTANCE. Nitrogen and gaseous air are pure substances.
CLASS Third Units PURE SUBSTANCE Pure substance: A substance that has a fixed chemical composition throughout. Air is a mixture of several gases, but it is considered to be a pure substance. Nitrogen and
Recovery of helium from rejected gas streams in Natural gas processing [1, 2, 3].
Gas Separation by Membranes Membrane technology in gas separation and purification has grown exponentially since they were first introduced about 30 years ago. Compared to other conventional gas separation
Layered polyaniline/graphene film from sandwich-structured polyaniline/graphene/polyaniline nanosheets for high-performance pseudosupercapacitors
Supporting Information for: Layered polyaniline/graphene film from sandwich-structured polyaniline/graphene/polyaniline nanosheets for high-performance pseudosupercapacitors Zhongqiu Tong a, Yongning Yang
Dynamic Simulation and Control of Vapor Recompression Column
The 7 th International Chemical Engineering Congress & Exhibition (IChEC 2011) Kish, Iran, 21-24 November, 2011 Dynamic Simulation and Control of Vapor Recompression Column Hojjat Dehghani, Mohammad Ali
RESEARCH OF BLOCKAGE SEGMENT DETECTION IN WATER SUPPLY PIPELINE BASED ON FLUID TRANSIENT ANALYSIS ABSTRACT
RESEARCH OF BLOCKAGE SEGMENT DETECTION IN WATER SUPPLY PIPELINE BASED ON FLUID TRANSIENT ANALYSIS Ying Xu 2, Yuebin Wu 1, Liang Chen 1, Yun Guo 2, Wei Wang 1 and Zhe Ding 2 1 School of Architecture, Harbin
4.1 Why is the Equilibrium Diameter Important?
Chapter 4 Equilibrium Calculations 4.1 Why is the Equilibrium Diameter Important? The model described in Chapter 2 provides information on the thermodynamic state of the system and the droplet size distribution.
Gas Pressure. Pressure is the force exerted per unit area by gas molecules as they strike the surfaces around them.
Chapter 5 Gases Gas Gases are composed of particles that are moving around very fast in their container(s). These particles moves in straight lines until they collides with either the container wall or
A Research on the Airflow Efficiency Analysis according to the Variation of the Geometry Tolerance of the Sirocco Fan Cut-off for Air Purifier
A Research on the Airflow Efficiency Analysis according to the Variation of the Geometry Tolerance of the Sirocco Fan Cut-off for Air Purifier Jeon-gi Lee*, Choul-jun Choi*, Nam-su Kwak*, Su-sang Park*
START UP MODELING OF KAIST MICRO MODULAR REACTOR COMPRESSOR USING BETA LINE METHOD WITH GAMMA+ CODE
The 6th International Supercritical CO2 Power Cycles Symposium March 27-29, 2018, Pittsburgh, Pennsylvania START UP MODELING OF KAIST MICRO MODULAR REACTOR COMPRESSOR USING BETA LINE METHOD WITH GAMMA+
CHEM 355 EXPERIMENT 7. Viscosity of gases: Estimation of molecular diameter
CHEM 355 EXPERIMENT 7 Viscosity of gases: Estimation of molecular diameter Expressed most simply, the viscosity of a fluid (liquid or gas) relates to its resistance to flow. The viscosity of a gas is determined
2. Introduction of nitrogen injection displacement for fire extinguishment
AGH Journal of Mining and Geoengineering vol. 36 No. 3 2012 Qijian Tang*, Ruxiang Qin**, Qinghua Chen**, Guoshu Zhang** APPLICATION OF NITROGEN INJECTION DISPLACEMENT FOR FIRE EXTINGUISHMENT 1. Introduction
DISTILLATION POINTS TO REMEMBER
DISTILLATION POINTS TO REMEMBER 1. Distillation columns carry out physical separation of liquid chemical components from a mixture by a. A combination of transfer of heat energy (to vaporize lighter components)
INTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK
INTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK ABSTRACT Ventilation stacks are becoming increasingly common in the design of naturally
6. Transport gases in blood
6. Transport gases in blood Artificial Lung G a s E x c h a n g e 2 Gas Exhange The absolute transfer rate of oxygen and carbon dioxide through the artificial lung is dependent on a number of factors:-
1 PIPESYS Application
PIPESYS Application 1-1 1 PIPESYS Application 1.1 Gas Condensate Gathering System In this PIPESYS Application, the performance of a small gascondensate gathering system is modelled. Figure 1.1 shows the
Ch. 11 Mass transfer principles
Transport of chemical species in solid, liquid, or gas mixture Transport driven by composition gradient, similar to temperature gradients driving heat transport We will look at two mass transport mechanisms,
THE PRESSURE SIGNAL CALIBRATION TECHNOLOGY OF THE COMPREHENSIVE TEST
THE PRESSURE SIGNAL CALIBRATION TECHNOLOGY OF THE COMPREHENSIVE TEST SYSTEM Yixiong Xu Mechatronic Engineering, Shanghai University of Engineering Science, Shanghai, China ABSTRACT The pressure signal
Effect of Coiled Capillary Tube Pitch on Vapour Compression Refrigeration System Performance
Effect of Coiled Capillary Tube Pitch on Vapour Compression Refrigeration System Performance Mutalubi Aremu Akintunde Federal University of Technology, Department of Mechanical Engineering Akure, Ondo
Kinetic-Molecular Theory
GASES Chapter Eleven Kinetic-Molecular Theory! Recall that our only previous description of gases stated that gases completely fill and take the shape of their containers.! The Kinetic-Molecular Theory
Traffic circles. February 9, 2009
Traffic circles February 9, 2009 Abstract The use of a traffic circle is a relatively common means of controlling traffic in an intersection. Smaller Traffic circles can be especially effective in routing
THE BEHAVIOR OF GASES
14 THE BEHAVIOR OF GASES SECTION 14.1 PROPERTIES OF GASES (pages 413 417) This section uses kinetic theory to explain the properties of gases. This section also explains how gas pressure is affected by
Technical Service Bulletin October 2013 TSB135.03
Technical Service Bulletin October 2013 TSB135.03 Backwash Optimization for HYDRAcap Analysis Systems by Qualitative This Technical Service Bulletin provides optimization information for the backwash process
Available online at ScienceDirect. Procedia Engineering 84 (2014 )
Available online at www.sciencedirect.com ScienceDirect Procedia Engineering 84 (014 ) 97 93 014 ISSST, 014 International Symposium on Safety Science and Technology Research of emergency venting time in
Fabrication of Novel Lamellar Alternating Nitrogen-Doped
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry A. This journal is The Royal Society of Chemistry 2017 Fabrication of Novel Lamellar Alternating Nitrogen-Doped Microporous Carbon
A. M. Dalavi, Mahesh Jadhav, Yasin Shaikh, Avinash Patil (Department of Mechanical Engineering, Symbiosis Institute of Technology, India)
IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE) ISSN(e) : 2278-1684, ISSN(p) : 2320 334X, PP : 45-49 www.iosrjournals.org Modeling, Optimization & Manufacturing of Vortex Tube and Application
Analyzing a Malfunctioning Clarifier with COMSOL s Mixture Model
Excerpt from the Proceedings of the COMSOL Conference 2008 Hannover Analyzing a Malfunctioning Clarifier with COMSOL s Mixture Model Arie C. de Niet,1, Arjen F. van Nieuwenhuijzen 1, and Arthur J. Geilvoet
This portion of the piping tutorial covers control valve sizing, control valves, and the use of nodes.
Piping Tutorial A piping network represents the flow of fluids through several pieces of equipment. If sufficient variables (flow rate and pressure) are specified on the piping network, CHEMCAD calculates
Membrane modules for nitrogen and oxygen generator systems. Technology Overview ENGINEERING YOUR SUCCESS.
Membrane modules for nitrogen and oxygen generator systems Technology Overview ENGINEERING YOUR SUCCESS. Parker modules the heart of OEM tailor-made nitrogen generators OEM (Original Equipment Manufacturer)
An Investigation of Liquid Injection in Refrigeration Screw Compressors
An Investigation of Liquid Injection in Refrigeration Screw Compressors Nikola Stosic, Ahmed Kovacevic and Ian K. Smith Centre for Positive Displacement Compressor Technology, City University, London EC1V
3 1 PRESSURE. This is illustrated in Fig. 3 3.
P = 3 psi 66 FLUID MECHANICS 150 pounds A feet = 50 in P = 6 psi P = s W 150 lbf n = = 50 in = 3 psi A feet FIGURE 3 1 The normal stress (or pressure ) on the feet of a chubby person is much greater than
Journal of Chemical and Pharmaceutical Research, 2014, 6(3): Research Article
Available online www.jocpr.com Journal of Chemical and Pharmaceutical Research 2014 6(3):304-309 Research Article ISSN : 0975-7384 CODEN(USA) : JCPRC5 World men sprint event development status research
Gas Law Worksheets - WS: Boyle s and Charles Law
Gas Law Worksheets - WS: Boyle s and Charles Law Boyle s Law states that the volume of a gas varies inversely with its pressure if temperature is held constant. (If one goes up the, other goes down.) We
A STUDY ON THE ENTRAPPED AIR BUBBLE IN THE PLASTICIZING PROCESS
A STUDY ON THE ENTRAPPED AIR BUBBLE IN THE PLASTICIZING PROCESS Hogeun Park, Bongju Kim, Jinsu Gim, Eunsu Han, and Byungohk Rhee, Ajou University, South Korea Abstract In injection molding, gas in the
Numerical simulation and analysis of aerodynamic drag on a subsonic train in evacuated tube transportation
Journal of Modern Transportation Volume 20, Number 1, March 2012, Page 44-48 Journal homepage: jmt.swjtu.edu.cn DOI: 10.1007/BF03325776 1 Numerical simulation and analysis of aerodynamic drag on a subsonic
Efficiency Improvement of Rotary Compressor by Improving the Discharge path through Simulation
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2014 Efficiency Improvement of Rotary Compressor by Improving the Discharge path through
Stress Analysis of The West -East gas pipeline with Defects Under Thermal Load
Stress Analysis of The West -East gas pipeline with Defects Under Thermal Load Abstract Xu Lei School of Petroleum Engineering, Yangtze University, Wuhan 430000, China 13071247220@163.com Natural gas is
Diffusivity in Gases Experiment ver 5.10b
Diffusivity in Gases Experiment ver 5.0b number of experimental techniques have been developed for the measurement of the diffusivity in gases. Both steady-state and unsteady-state methods are used. However,
Available online at ScienceDirect. Physics Procedia 67 (2015 )
Available online at www.sciencedirect.com ScienceDirect Physics Procedia 67 (2015 ) 392 397 25th International Cryogenic Engineering Conference and the International Cryogenic Materials Conference in 2014,
Experimental Analysis on Vortex Tube Refrigerator Using Different Conical Valve Angles
International Journal of Engineering Research and Development e-issn: 7-067X, p-issn: 7-00X, www.ijerd.com Volume 3, Issue 4 (August ), PP. 33-39 Experimental Analysis on Vortex Tube Refrigerator Using
THE GUIDE TO MEMBRANE NITROGEN GENERATORS
THE GUIDE TO MEMBRANE NITROGEN GENERATORS MEMBRANE NITROGEN GENERATORS The membrane nitrogen generator utilizes a hollow porous fiber to separate the N 2 molecules from other molecules, including O 2.
Flow and Mixing in the Liquid between Bubbles
Excerpt from the Proceedings of the COMSOL Conference 2009 Boston Flow and Mixing in the Liquid between Bubbles Bruce A. Finlayson, Professor Emeritus of Chemical Engineering Department of Chemical Engineering,
Modeling and Process Design
Journal of Applied Science (2010), Volume 10 (12): 1134-1139 Removal of CO2 from Natural Gas using Membrane Separation System: Modeling and Process Design 1 F. Ahmad, K. K. Lau, A. M. Shariff Chemical
Numerical simulation of three-dimensional flow field in three-line rollers and four-line rollers compact spinning systems using finite element method
Indian Journal of Fibre & Textile Research Vol. 42, March 2017, pp. 77-82 Numerical simulation of three-dimensional flow field in three-line rollers and four-line rollers compact spinning systems using
Two-stage pulse tube refrigerator with step displacer as phase shifter
IOP Conference Series: Materials Science and Engineering PAPER OPEN ACCESS Two-stage pulse tube refrigerator with step displacer as phase shifter To cite this article: Shaowei Zhu 2015 IOP Conf. Ser.:
Supporting Information. Metal organic framework-derived Fe/C Nanocubes toward efficient microwave absorption
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry A. This journal is The Royal Society of Chemistry 2015 Supporting Information Metal organic framework-derived Fe/C Nanocubes toward
The Estimation Of Compressor Performance Using A Theoretical Analysis Of The Gas Flow Through the Muffler Combined With Valve Motion
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering The Estimation Of Compressor Performance Using A Theoretical Analysis Of The Gas Flow Through
HYDROGEN FAST FILLING TO A TYPE IV TANK DEVELOPED FOR MOTORCYCLES
HYDROGEN FAST FILLING TO A TYPE IV TANK DEVELOPED FOR MOTORCYCLES Yamada, E. 1, Hiraki, W. 2, and Muramatsu, H. 3 1 FC-EV Research Division, Japan Automobile Research Institute, 1328-23 Takaheta, Osaka,
DISTILLATION PRESSURE CONTROL TROUBLESHOOTING THE HIDDEN PITTFALLS OF OVERDESIGN
Distillation Absorption 2010 A.B. de Haan, H. Kooijman and A. Górak (Editors) All rights reserved by authors as per DA2010 copyright notice DISTILLATION PRESSURE CONTROL TROUBLESHOOTING THE HIDDEN PITTFALLS
DRINKING WATER - LAB EXPERIMENTS LAB EXPERIMENTS. Nanofiltration
DRINKING WATER - LAB EXPERIMENTS LAB EXPERIMENTS Nanofiltration nanofiltration lab experiments Framework This module explains the lab experiment on nanofiltration. Contents This module has the following
Research of Variable Volume and Gas Injection DC Inverter Air Conditioning Compressor
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2016 Research of Variable Volume and Gas Inection DC Inverter Air Conditioning Compressor
AIR PRESSURE CONTROLLED MASS MEASUREMENT SYSTEM
Measurement of Mass, Force and Torque (APMF 2013) International Journal of Modern Physics: Conference Series Vol. 24 (2013) 1360002 (6 pages) The Authors DOI: 10.1142/S2010194513600021 AIR PRESSURE CONTROLLED
CHEMISTRY - CLUTCH CH.5 - GASES.
!! www.clutchprep.com CONCEPT: UNITS OF PRESSURE Pressure is defined as the force exerted per unit of surface area. Pressure = Force Area The SI unit for Pressure is the, which has the units of. The SI
CHAPTER 31 IDEAL GAS LAWS
CHAPTER 31 IDEAL GAS LAWS EXERCISE 144, Page 317 1. The pressure of a mass of gas is increased from 150 kpa to 750 kpa at constant temperature. Determine the final volume of the gas, if its initial volume
SIMULATION OF ENTRAPMENTS IN LCM PROCESSES
Douai, FRANCE - July 6 SIMULATION OF ENTRAPMENTS IN LCM PROCESSES René Arbter, Paolo Ermanni Centre of Structure Technologies ETH Zurich, Leonhardstr. 7, 89 Zurich, Switzerland: rarbter@ethz.ch ABSTRACT:
CSU_Yunlu 2D Soccer Simulation Team Description Paper 2015
CSU_Yunlu 2D Soccer Simulation Team Description Paper 2015 Tao Huang, Jieli Yin Fu Jiang, Xiaoyong Zhang, Jun Peng School of Information Science and Engineering, Central South University, Changsha, Hunan
Generating Calibration Gas Standards
Technical Note 1001 Metronics Inc. Generating Calibration Gas Standards with Dynacal Permeation Devices Permeation devices provide an excellent method of producing known gas concentrations in the PPM and
Interconnected hierarchical NiCo 2 O 4 microspheres as high performance. electrode material for supercapacitor
Electronic Supplementary Material (ESI) for Dalton Transactions. This journal is The Royal Society of Chemistry 2017 Interconnected hierarchical microspheres as high performance electrode material for
1. A pure substance has a specific volume of 0.08 L/mol at a pressure of 3 atm and 298 K. The substance is most likely:
Name: September 19, 2014 EXAM 1 P a g e 1 1. A pure substance has a specific volume of 0.08 L/mol at a pressure of 3 atm and 298 K. The substance is most likely: a. Liquid b. Gas c. Supercritical Fluid
Micro Channel Recuperator for a Reverse Brayton Cycle Cryocooler
Micro Channel Recuperator for a Reverse Brayton Cycle Cryocooler C. Becnel, J. Lagrone, and K. Kelly Mezzo Technologies Baton Rouge, LA USA 70806 ABSTRACT The Missile Defense Agency has supported a research
Supporting information
Electronic Supplementary Material (ESI) for Journal of Materials Chemistry A. This journal is The Royal Society of Chemistry Please do 2018 not adjust margins Supporting information Self-assembled 3D flower-like
Kinetic Molecular Theory imaginary Assumptions of Kinetic Molecular Theory: Problems with KMT:
AP Chemistry Ms. Ye Name Date Block Kinetic Molecular Theory Explains properties of gases, liquids, and solids in terms of energy using an ideal gas, an imaginary which fits all the assumptions of kinetic
Analysis of Pressure Rise During Internal Arc Faults in Switchgear
Analysis of Pressure Rise During Internal Arc Faults in Switchgear ASANUMA, Gaku ONCHI, Toshiyuki TOYAMA, Kentaro ABSTRACT Switchgear include devices that play an important role in operations such as electric
You should be able to: Describe Equipment Barometer Manometer. 5.1 Pressure Read and outline 5.1 Define Barometer
A P CHEMISTRY - Unit 5: Gases Unit 5: Gases Gases are distinguished from other forms of matter, not only by their power of indefinite expansion so as to fill any vessel, however large, and by the great
Investigation of Suction Process of Scroll Compressors
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2006 Investigation of Suction Process of Scroll Compressors Michael M. Cui Trane Jack Sauls
End of Chapter Exercises
End of Chapter Exercises Exercises 1 12 are conceptual questions that are designed to see if you have understood the main concepts of the chapter. 1. While on an airplane, you take a drink from your water
The Use of a Process Simulator to Model Aeration Control Valve Position and System Pressure
The Use of a Process Simulator to Model Aeration Control Valve Position and System Pressure Matthew Gray 1 * and Steve Kestel 1 1 BioChem Technology, King of Prussia, PA *Email: mgray@biochemtech.com ABSTRACT
Practice MC Test unit D (Ch 10) Gas Laws (pg 1 of 10)
Practice MC Test unit D (Ch 10) Gas Laws (pg 1 of 10) This is practice - Do NOT cheat yourself of finding out what you are capable of doing. Be sure you follow the testing conditions outlined below. DO
Domain Decomposition Method for 3-Dimensional Simulation of the Piston Cylinder Section of a Hermetic Reciprocating Compressor
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2006 Domain Decomposition Method for 3-Dimensional Simulation of the Piston Cylinder Section
Hierachical Nickel-Carbon Structure Templated by Metal-Organic Frameworks for Efficient Overall Water Splitting
Electronic Supplementary Material (ESI) for Energy & Environmental Science. This journal is The Royal Society of Chemistry 2018 Electronic Supplementary Information Hierachical Nickel-Carbon Structure
A Depletion Compensated Wet Bath Simulator For Calibrating Evidential Breath Alcohol Analyzers
A Depletion Compensated Wet Bath Simulator For Calibrating Evidential Breath Alcohol Analyzers Slemeyer, A. University of Applied Sciences of Giessen, Dept. of Electrical Engineering 1 Wiesenstr. 14, D-35390
Accurate Measurement of Steam Flow Properties
Accurate Measurement of Steam Flow Properties Kewen Li and Roland N. Horne Stanford Geothermal Program, Stanford University (Proceedings of 1999 GRC Annual Meeting on October 17-20, Reno, California, USA)
Question McGraw-Hill Ryerson Limited
Question 1 Which of the following cannot be explained by considering the empty space between the particles of a gas? A) Gases are more compressible than liquids. B) Gases have lower viscosities than liquids.
Research on ESC Hydraulic Control Unit Property and Pressure Estimation
Research on ESC Hydraulic Control Unit Property and Pressure Estimation Liu Wei, Ding Haitao *, and Guo Konghui State Key Libratory of Automobile Dynamic Simulation, Jilin University, Changchun 30025,
Supplementary Information. High areal capacity lithium sulfur battery cathode by. site-selective vapor infiltration of hierarchical
Electronic Supplementary Material (ESI) for Nanoscale. This journal is The Royal Society of Chemistry 2017 Supplementary Information High areal capacity lithium sulfur battery cathode by site-selective
Numerical Simulation And Aerodynamic Performance Comparison Between Seagull Aerofoil and NACA 4412 Aerofoil under Low-Reynolds 1
Advances in Natural Science Vol. 3, No. 2, 2010, pp. 244-20 www.cscanada.net ISSN 171-7862 [PRINT] ISSN 171-7870 [ONLINE] www.cscanada.org *The 3rd International Conference of Bionic Engineering* Numerical
Analysis of Steady-state Characteristics of Aerodynamic Bearing Based on FLUENT JIA Chenhui 1,a, Du Caifeng 2,b and QIU Ming 3,c
International Conference on Intelligent Systems Research and Mechatronics Engineering (ISRME 2015) Analysis of Steady-state Characteristics of Aerodynamic Bearing Based on FLUENT JIA Chenhui 1,a, Du Caifeng
CHEM 3351 Physical Chemistry I, Fall 2017
CHEM 3351 Physical Chemistry I, Fall 2017 Problem set 1 Due 9/15/2017 (Friday) 1. An automobile tire was inflated to a pressure of 24 lb in -2 (1.00 atm = 14.7 lb in -2 ) on a winter s day when the temperature
Available online at Procedia Engineering 45 (2012 )
Available online at www.sciencedirect.com Procedia Engineering 45 (212 ) 496 51 212 International Symposium on Safety Science and Technology Study on nitrogen preparation system based on simulation experiment
How To Use Getters and Getter Pumps
A Journal of Practical and Useful Vacuum Technology From By Phil Danielson How To Use Getters and Getter Pumps Gettering is a vacuum pumping technology that has been with us, in many forms, for almost
Gases and Pressure. Main Ideas
Gases and Pressure Key Terms pressure millimeters of mercury partial pressure newton atmosphere of pressure Dalton s law of partial pressures barometer pascal In the chapter States of Matter, you read