CIRCUMFERENTIAL NONUNIFORMITY OF WAVES ON LIQUID FILM IN ANNULAR FLOW WITHOUT LIQUID ENTRAINMENT
|
|
- Rosa Sharp
- 6 years ago
- Views:
Transcription
1 Interfacial Phenomena and Heat Transfer, 1 (2): (2013) CIRCUMFERENTIAL NONUNIFORMITY OF WAVES ON LIQUID FILM IN ANNULAR FLOW WITHOUT LIQUID ENTRAINMENT S. V. Alekseenko, 1,2 A. V. Cherdantsev, 1,2, S. V. Isaenkov, 1,2 & D. M. Markovich 1,2 1 Novosibirsk State University, 2, Pirogov St., Novosibirsk , Russia 2 Kutateladze Institute of Thermophysics, 1, Lavrentiev Ave., Novosibirsk , Russia Address all correspondence to A. V. Cherdantsev, cherdantsev@itp.nsc.ru The wavy structure of liquid film in downward annular flow without liquid entrainment is studied. Temporal evolution of instantaneous distributions of local film thickness over longitudinal and circumferential coordinates is studied using high-speed laser-induced fluorescence technique. Wavy structure in such flow consists of fast long-living primary waves and slow short-living secondary waves that are generated at the back slopes of primary waves. An automatic algorithm of identification of characteristic lines of primary waves is applied to data obtained in a number of circumferential positions. Contours of waves in each time frame are identified to obtain temporal evolution of the shape of each wave in longitudinal and circumferential coordinates. Circumferential size of primary waves is estimated based on frequency of different kinds of waves. It is shown that variation of primary waves height along circumferential coordinate is most likely caused by absorption and generation of secondary waves. KEY WORDS: annular flow, gas shear, laser-induced fluorescence, wavy structure 1. INTRODUCTION The term annular flow is applied to the flow of liquid film along pipe walls together with high-velocity gas stream along pipe center. Interaction of the gas stream and liquid film leads to the appearance of complicated wavy structure on film surface. Wavy processes substantially change heat and mass transfer and pressure drop in flow. At high liquid flow rates, liquid droplets are entrained from film surface into the gas core. The entrainment phenomenon also exerts essential influence on integral characteristics of the flow. Wavy structure in annular flow is different in cases of the presence or absence of liquid entrainment. In regimes with entrainment, large-amplitude disturbance waves appear on the film surface. Disturbance waves coexist with small-scale ripples. The ripples can travel either on the base film layer between disturbance waves, or on the disturbance waves themselves. Ripples on disturbance waves can be disrupted by the gas shear into droplets (Woodmansee and Hanratty, 1969). This phenomenon is regarded as one of the main sources of entrainment. For flow regimes without entrainment, it was considered earlier that only the ripples are present on the film surface. A large amount of experimental work is devoted to studying amplitude, velocity, and frequency of disturbance waves (e.g., Chu and Dukler, 1975; Azzopardi, 1986; Han et al., 2006; Sawant et al., 2008). Ripples in regimes without entrainment are less studied: Asali and Hanratty (1993) measured ripples wavelength, Hagiwara et al. (1985) measured ripples frequency and amplitude. Recently, Alekseenko et al. (2009) have shown that there exists similarity between flow regimes with and without liquid entrainment. Using the high-speed laser-induced fluorescence (LIF) technique, they studied temporal and spatial evolution of waves with high resolution in space and time. It was found that in flow with entrainment, all the ripples are /13/$35.00 c 2013 by Begell House, Inc. 139
2 140 Alekseenko et al. NOMENCLATURE A amplitude of primary waves h p peak height of primary waves d pipe diameter L circumferential size of the area F c frequency of primary waves, occupying of measurements the whole visible area L p circumferential size of primary waves F e frequency of edges of primary waves L s circumferential size of secondary waves F tot frequency of all primary waves Re liquid film Reynolds number, Re = 4q/πdν F y frequency of primary waves at q volumetric liquid flow rate circumferential position y t time h film thickness ν kinematic viscosity of liquid h b thickness of the base film between V g superficial gas velocity primary waves x longitudinal coordinate h T threshold value of film thickness y circumferential coordinate generated at the back slopes of disturbance waves and travel either faster or slower than the disturbance waves. In flow without entrainment, two types of waves exist on the film surface: primary waves with larger velocity, amplitude, and lifetime; and small-scale secondary waves that are generated at the back slopes of primary waves. Thus, the behavior of primary and secondary waves in flow without entrainment is similar to the behavior of, respectively, disturbance waves and ripples in flow with entrainment. The main difference consists in the absence of secondary waves that would move faster than primary waves. Crests of primary waves are not covered by smaller waves that could be disrupted by the gas shear and contribute to entrainment. In most experimental works, measurements were performed in one circumferential position of the pipe. Such approach might provide incorrect information on waves behavior and characteristics due to possible circumferential nonuniformity of waves. The problem of circumferential nonuniformity was investigated in a relatively small number of papers. Circumferential coherence of disturbance waves was studied by Hewitt and Lovegrove (1969), Azzopardi and Gibbons (1983), Martin and Azzopardi (1985), and Sekoguchi et al. (1985). According to these papers, disturbance waves form full rings in small (less than 3 cm) diameter pipes, though the height of waves is not uniform around the circumference of the pipe. An increase of pipe diameter leads to the appearance of circumferentially localized disturbance waves; the fraction of localized waves increases with pipe diameter. The same is true for the growth of gas velocity. Circumferential profiles of disturbance waves height, obtained by Belt et al. (2010), show that variation of disturbance waves height is of the same order of magnitude as a wave s height. Photographs of film surface, presented by Asali and Hanratty (1993), show that waves in regimes without entrainment are circumferentially localized. Ohba and Nagae (1993) found two types of waves in flow without entrainment. The waves were different by many parameters, including circumferential size. Waves with larger circumferential size were named ring waves, since they occupied all the visible part of the pipe, and it was considered that they form full rings around pipe circumference. The other type of wave was identified as ripples. Comparison of waves velocity, measured by Ohba and Nagae, to velocity of waves, observed by Alekseenko et al. (2009), leads to the conclusion that ring waves and ripples correspond to primary and secondary waves, respectively. In Alekseenko et al. (2012), the LIF method was applied to study evolution of waves in three dimensions (longitudinal and circumferential coordinates and time). For flow with entrainment, it was found that circumferential nonuniformity of disturbance waves exerts influence on the generation of ripples. For flow without entrainment, it was found that primary waves do not form full rings around pipe circumference, since edges of primary waves are often encountered. Thus, the term ring waves, used by Ohba and Nagae, is not correct. The circumferential size of Interfacial Phenomena and Heat Transfer
3 Circumferential Nonuniformity of Waves 141 secondary waves is smaller than that of primary waves; generation of secondary waves occurs either at the central parts or at the edges of primary waves. The present paper is a continuation of Alekseenko et al. (2012). The scope of the present paper is to provide quantitative information on circumferential nonuniformity of waves in annular flow without entrainment. For this purpose, a new automatic algorithm of identification and processing of waves is developed. 2. EXPERIMENTAL SETUP AND MEASUREMENT TECHNIQUE Downward annular flow is studied in two vertical Plexiglas pipes with inner diameters d = 15 mm and d = 11.7 mm and length 1 m. Each pipe has a flat outer section to avoid optical distortions at the outer surface of the pipe. Gas stream entered the working section through coaxial pipe of smaller diameter. Working liquid was introduced through a ringshaped slot between the inner surface of the pipe and the outer surface of gas-feeding tube; the slot thickness is 0.5 mm. Two water-glycerol solutions were used as working liquids. Flow parameters used for each pipe are given in Table 1. Liquid Reynolds number Re is defined as 4q/πdν, where q is volumetric flow rate of liquid, ν is kinematic viscosity of liquid. For these flow conditions no liquid entrainment occurs at any gas velocity. The absence of entrainment was also validated directly using the standard sampling probe technique: no liquid flow through the probe was observed during long-time runs. LIF technique was used for film thickness measurements. Fluorescent dye (Rhodamine 6G) was dissolved in liquid in low (30 mg/l) concentration. A continuous 2W laser with wavelength of 532 nm was used for excitation of fluorescence. Brightness of fluorescent light was measured by high-speed digital camera, equipped with an orange filter. Brightness is then converted into local film thickness using a calibration curve. Details of the calibration procedure are given in Alekseenko et al. (2012). A fragment of the visible part of the tube was used as the area of measurement (which is marked by the dashed line in Fig. 1). Its longitudinal size is 12 cm; the circumferential size of the area of measurements L is equal to 1/4 of the pipe perimeter. Laser beam was spread to enlighten the area of measurements using scattering length. The spatial resolution is 0.2 mm in both the longitudinal and circumferential directions. The sampling frequency is relatively low TABLE 1: Flow parameters Pipe diameter, mm Viscosity of working liquid, m 2 /s Liquid Reynolds number 72,172 60,140 Superficial gas velocity, m/s Sampling frequency, khz Spatial resolution, mm FIG. 1: Area of measurements Volume 1, Number 2, 2013
4 142 Alekseenko et al. (0.5 and 2 khz), since the large size of the area of measurements makes high demands on the local illumination of the film surface. Measurements were performed at the distances equal to 40 pipe diameters below the inlet. For flow regimes without liquid entrainment this distance is sufficient for stabilization of waves properties (see, e.g., Hagiwara et al., 1985). 3. DATA REPRESENTATION AND PROCESSING Obtained data represent evolution of film thickness h in three dimensions: longitudinal coordinate x, circumferential coordinate y, and time t. Two kinds of data representation will be used for further data processing. 3.1 Processing of x t Representation of Data Surface h(x, t) at fixed y enables one to study the spatial and temporal evolution of waves in one longitudinal section of the pipe. This approach was applied for a single longitudinal section in Alekseenko et al. (2009). An example of such surface is given in Fig. 2. In this image brightness is directly proportional to film thickness. The vertical axis corresponds to time, and horizontal axis to longitudinal distance. The flow direction is from left to right. Waves are visible in this image as brighter bands crossing this surface along their characteristic lines. The slope of a characteristic line to the t axis is proportional to the wave s velocity. Primary waves can be distinguished by larger values of velocity, amplitude, and lifetime. Secondary waves appear at the back slopes of primary ones; they travel along the base film between primary waves with lower velocity until the following primary waves absorb them. An automatic technique of identification of characteristic lines of primary waves was developed recently by Alekseenko et al. (2013). The technique is based on the Canny method of edges detection, which is often applied in image analysis. The Canny method consists of searching for local maxima in the response of the signal to the Gaussian filter. As a result, it marks the areas of maximum gradient of image brightness (Canny, 1986). When this method is applied to the matrix h(x, t) h x (x, t) =, (1) x it marks crests of waves. The marked positions of a wave s crest in different time moments are then concatenated into the characteristic line of the wave. Primary waves are characterized by larger values of velocity and lifetime in comparison to secondary waves. The product of velocity and lifetime gives longitudinal distance, over which the wave is observed. This distance is used as a criterion to separate primary and secondary waves. After that, velocity, amplitude, and frequency of primary waves are measured. At relatively low gas velocities the technique almost does FIG. 2: Fragment of h(x, t) surface with marked crests of primary waves. d = 11.7 mm, Re = 60, V g = 18 m/s. Interfacial Phenomena and Heat Transfer
5 Circumferential Nonuniformity of Waves 143 not miss primary waves, so it can be used for measuring the frequency of primary waves as well. Crests of primary waves are marked by white dots in Fig. 2. A number of longitudinal sections with step 1 mm are investigated (12 sections for d = 15 mm and 9 sections for d = 11.7 mm). Figure 3 shows the passing frequency (a), velocity (b), and height (c) of primary waves in different longitudinal sections for d = 15 mm. Frequency and velocity tend to be the same at different circumferential positions; this behavior is consistent with the basic assumption that the time-averaged characteristics of the flow are circumferentially uniform. The waves height is evidently overestimated far from the centerline of the area of measurements. This is related to deviation of the optical path from the normal to film surface. Estimation of the ratio h/h 0 at different circumferential positions was calculated earlier (see Fig. 4 in Alekseenko et al., 2012); behavior of this ratio is similar to that of waves height. FIG. 3: Average frequency (a), velocity (b), and height (c) of primary waves in different circumferential positions. d = 15 mm, Re = 72. (1) V g = 18 m/s, (2) V g = 22 m/s, (3) V g = 27 m/s. For (c), numbers 4 6 denote values of base film thickness. Volume 1, Number 2, 2013
6 144 Alekseenko et al. FIG. 4: Comparison of the average frequency (a), velocity (b), and height (c) of primary waves in different pipes. (1) d = 11.7 mm, Re = 60; (2) d = 11.7 mm, Re = 140; (3) d = 15 mm, Re = 72; (4) d = 15 mm, Re = 172. To minimize the influence of this distortion on further processing, the data were compensated as follows: h (x, y, t) = h b (y 0 ) + [h(x, y, t) h b(y)] [h p (y 0 ) h b (y 0 )] h p (y) h b (y) (2) Here, h p is average height of primary waves, observed in given longitudinal section; h b is thickness of the base film between primary waves (defined as the most probable value of film thickness); y 0 corresponds to the central longitudinal section, where the distortion is expected to be minimal. Figure 4 presents comparison of frequency (a), velocity (b), and height (c) of primary waves for different experimental conditions. Each point in this image is the result of averaging by all processed longitudinal sections. Frequency and velocity of primary waves grow almost linearly when gas velocity increases; the height of primary waves decreases with the growth of gas velocity. All three characteristics are growing with liquid flow rate. Unfortunately, data for different pipe diameters are also different in liquid viscosity, so it is not always clear which parameter defines the difference in waves properties. According to our earlier experiments, performed in a two-dimensional approach, Interfacial Phenomena and Heat Transfer
7 Circumferential Nonuniformity of Waves 145 an increase of liquid viscosity leads to an increase of primary waves velocity and height and almost does not change the frequency of waves. Thus, we suppose that the main source of difference in waves properties, observed in Fig. 4, is the viscosity of liquid. 3.2 Processing of x y Representation of Data Surface h(x, y) represents the real instantaneous shape of the film surface in the area of measurements [Fig. 5(a)]. As it was mentioned above, the circumferential size of primary waves is always larger than the circumferential size of the area of measurements L. At the same time, edges of primary waves are often encountered in the area of measurements. This means that the circumferential size of primary waves is smaller than the pipe perimeter. The circumferential size of secondary waves is normally smaller than L, and the secondary waves can be generated by either central parts or edges of primary waves. To study the shape of a primary wave in longitudinal and circumferential dimensions, contours of primary waves were identified. Contours were defined as lines in h(x, y) surface where the surface crosses the threshold value of film thickness ht. When searching for primary waves, ht was defined as < h > + (< h > - hb ) in order to exceed the height of secondary waves. Here, < h > denotes average film thickness. An example of h(x, y) surface with marked contours of two primary waves is shown in Fig. 5(b). The contours were related to primary waves if they enclosed crests of primary waves, marked at the previous stage in any longitudinal section passing through the contour. After that, contours obtained in different time moments were related to certain primary wave if they enclosed the same characteristic lines, obtained earlier. As the result, for each primary wave, contour on x y surface at each time moment of its life was obtained. For the secondary waves, there is no information on their characteristic lines in the x t approach, since the automatic method, described in the previous subsection, fails to identify them reliably. Thus, the algorithm is slightly different for secondary waves. At the first stage, areas of the base film between primary waves were selected for further processing. At the base film, the same searching for contours is performed with ht = < h >. After that, for each contour, the nearest contour in the neighboring frame was found. The two contours are considered to belong to the same secondary wave if the longitudinal shift between them roughly corresponds to the velocity of secondary waves, and the circumferential sizes are close enough to each other. In this case, the next frame is analyzed. (a) (b) FIG. 5: Fragment of h(x, y) surface. (a) Edges of primary waves; (b) Contours of primary waves. d = 15 mm, Re = 72, V g = 18 m/s. Volume 1, Number 2, 2013
8 146 Alekseenko et al. Figure 6 shows an example of the evolution of a contour of a single secondary wave in six subsequent time moments. 4. RESULTS AND DISCUSSION The goal of the present paper is to study the circumferential nonuniformity of liquid film wavy structure. The degree of nonuniformity of waves is characterized by their typical circumferential size and variation of their amplitude by the circumferential coordinate. 4.1 Circumferential Size of Primary and Secondary Waves It is impossible to measure the circumferential size of primary waves directly, since it is always larger than that of the area of measurements L. Nonetheless, it can be estimated using relative frequencies of waves, occupying the whole area of measurements ( centers ) and waves, occupying only part of the area ( edges ). Estimation is based on two assumptions: (1) circumferential distribution of waves position is uniform; (2) distribution of primary waves by the circumferential size is symmetric around the average circumferential size L p. In this case, relative frequencies F c (frequency of centers) and F e (frequency of edges) are defined by L p and L. The idea is illustrated in Fig. 7. Waves with the left border located within the area S c will be seen as centers in the area of measurements (left-hand part of Fig. 7). The length of this area is defined as S c = L p L. Waves with either the left or right border located within the area of measurements will be seen as edges (middle part of Fig. 7). The length of such areas for left and right edges is defined as S le = S re = L. Thus, the ratio of frequencies is defined as the ratio of lengths of these areas: F c S c = = L p L F e S le + S re 2L (3) Hence, circumferential size L p is defined as ( L p = L 1 + 2F ) c. (4) F e FIG. 6: Example of evolution of contour of a secondary wave. d = 15 mm, Re = 72, V g = 18 m/s. Interfacial Phenomena and Heat Transfer
9 Circumferential Nonuniformity of Waves 147 FIG. 7: Possible position of primary waves, visible as centers (top) and edges (bottom) For the case when L p is larger than πd L, the situation is more complicated, since both edges might appear in the area of measurements (which corresponds to the position of the left edge within S lre region in the right-hand part of Fig. 7). The length of this area is defined as S lre = L (πd L p ). The appearance of only one edge corresponds to the position of the left edge in the regions S le or S re (the right-hand part of Fig. 7). The length of each of these two regions in this case is defined as S le = S re = πd L p. The expression for S c remains the same; the ratio of frequencies is then defined as F c F e = S c = L p L S le + S re + 2 S lre 2L S lre is multiplied by 2, since in this case two edges appear in the working area. Thus, the result coincides with that of relation (3), and relation (4) is applicable for the case of large L p as well. Two methods are used to measure F c and F e. The first one is to measure sizes of contours of waves directly. The second one is to estimate these values on the basis of two quantities: passing frequency of primary waves in any longitudinal section F y (see Section 3.1) and total number of primary waves obtained in h(x, y, t) coordinates F tot (see Section 3.2). These quantities are expected to be related to F c and F e as F tot = F c + F e, F y = F c + F e /2 (6) The latter equation is derived as follows: (1) All the centers pass through each longitudinal section; (2) Frequency of either the left or right edges linearly changes with y between 0 on one side and F e /2 on the other (since we assume that circumferential distribution of waves position is uniform). The sum frequency of the left and right edges for given y is F e /2 [since F y does not depend on y; see Fig. 3(a)]. Thus, F e = 2(F tot F y ), F c = 2F y F tot. (7) Substituting (7) into (4), the following relation for L p as a function of L, F tot and F y is obtained: F y L p = L (8) F tot F y Both methods of measuring F c and F e are quite sensitive to the threshold value h T. Several additional tests were performed in order to validate that h T satisfies the following requirements: (1) h T should be large enough so that contours of primary waves would not merge with contours of adjacent primary or secondary waves; (2) h T should be small enough so that contours of primary waves would not split into smaller ones. In most cases, there was no big difference between initial and improved values of h T. The second method was found to be slightly more reliable, since it is less sensitive to the threshold value. Results are given in Fig. 8 in (5) Volume 1, Number 2, 2013
10 148 Alekseenko et al. FIG. 8: Estimation of circumferential size of primary waves. (1) d = 15 mm, Re = 72, ν = m 2 /s. (2) d = 11.7 mm, Re = 60, ν = m 2 /s. dimensionless form L p /d, along with uncertainty range. Estimated values of L p slightly decrease with V g. The circumferential size is much smaller for lesser diameter. We suppose that this difference is mainly defined by the difference in liquid viscosity and liquid flow rate, normalized by pipe perimeter (defined as Re ν). For the secondary waves, circumferential size L s can be measured directly, as time-averaged circumferential size of obtained contours (see Fig. 6). To increase the reliability of measurements, only the waves with long enough lifetime (three time instants or more), lying inside the area of measurements, were selected. Distribution of secondary FIG. 9: Distribution of secondary waves by circumferential size at different gas velocities, normalized by the total number of waves. (a) d = 15 mm, Re = 72, ν = m 2 /s. (b) d = 11.7 mm, Re = 60, ν = m 2 /s. (1) V g = 18 m/s; (2) V g = 22 m/s; (3) V g = 27 m/s; (4) V g = 36 m/s; (5) V g = 44 m/s. Interfacial Phenomena and Heat Transfer
11 Circumferential Nonuniformity of Waves 149 waves on circumferential size is nearly the same for different values of gas velocity (Fig. 9). The most probable value of L s lies around 3 mm for d = 15 mm and 2 mm for d = 11.7 mm. 4.2 Variation of Primary Waves Height Figure 10(a) shows example of wave s height variation along the circumferential coordinate at a fixed moment of time. Although the wave s height oscillates along this direction, we should note that peak height is also not stable in the longitudinal direction: it oscillates with time [Fig. 10(b)]. One possible reason for such oscillations is interaction of the primary wave to secondary waves. Due to such interactions, the height of the wave grows when it absorbs secondary waves, and diminishes when it generates secondary waves. Such behavior is clearly seen for wave II in Fig. 6 in Alekseenko et al. (2009). Since secondary waves are characterized by a relatively small circumferential size, the temporal change of a primary wave s amplitude is expected to be localized by the circumferential coordinate. Thus, we suppose that the circumferential variation is caused by such localized interactions. Circumferential and longitudinal variation of primary waves amplitude and amplitude of secondary waves are compared in Fig. 11. Variation is defined as δa(y) = std (A(y)) std (A(t)), δa(t) = < A > < A >, where A = h p h b (9) The average amplitude of secondary waves is also normalized by < A >. It can be seen that circumferential variation is of the same order of magnitude, as longitudinal variation and both variations are smaller than the amplitude of secondary waves. This observation supports the hypothesis described above. 5. CONCLUSIONS Three-dimensional structure of waves on the surface of gas-sheared liquid film is studied using a high-speed laserinduced fluorescence technique. Wavy structure in such flow regime consists of fast long-living primary waves and slow short-living secondary waves. Secondary waves are generated at the back slopes of primary waves. FIG. 10: Example of change of height of a primary wave with circumferential coordinate in fixed time moment (a) and with time at fixed circumferential position (b) Volume 1, Number 2, 2013
12 150 Alekseenko et al. FIG. 11: Variation of primary waves amplitude. (a) d = 15 mm, Re = 72, ν = m 2 /s. (b) d = 11.7 mm, Re = 60, ν = m 2 /s. (1) Variation with time; (2) Variation with circumferential coordinate; (3) Relative amplitude of secondary waves. Velocity, frequency, and height of primary waves are measured. A way to compensate circumferential distortion of film thickness data for further investigation is developed. An automatic algorithm that enables one to get the temporal evolution of either primary or secondary waves in both longitudinal and circumferential coordinates is developed. The circumferential size of primary waves is estimated based on primary waves frequency in different longitudinal sections, and the circumferential size of secondary waves is measured directly. The circumferential size of primary waves decreases with gas velocity; the influence of gas velocity on average circumferential size of secondary waves is weak. It is shown that variation of amplitude of primary waves by circumferential coordinate is most likely caused by the absorption and generation of secondary waves. ACKNOWLEDGMENTS The work was supported by Russian Foundation for Basic Research (grants and ); and President of Russian Federation (grants MK and NSh ); Government of Russian Federation (project 11.G ). REFERENCES Alekseenko, S. V., Antipin, V. A., Cherdantsev, A. V., Kharlamov, S. M., and Markovich, D. M., Two-wave structure of liquid film and waves interrelation in annular gas-liquid flow with and without entrainment, Phys. Fluids, vol. 21, pp , Alekseenko, S., Cherdantsev, A., Cherdantsev, M., Isaenkov, S., Kharlamov, S., and Markovich, D., Application of a high-speed laser-induced fluorescence technique for studying three-dimensional structure of annular gas-liquid flows, Exp. Fluids, vol. 53, no. 1, pp , Alekseenko, S. V., Cherdantsev, A. V., Heinz, O. M., Kharlamov, S. M., and Markovich, D. M., Application of the image-analysis method to studies of the space-time wave evolution in an annular gas-liquid flow, Patt. Recogn. Image Anal., vol. 23, no. 1, pp , Interfacial Phenomena and Heat Transfer
13 Circumferential Nonuniformity of Waves 151 Asali, J. C. and Hanratty, T. J., Ripples generated on a liquid film at high gas velocities, Int. J. Multiphase Flow, vol. 19, pp , Azzopardi, B. J., Disturbance wave frequencies, velocities and spacing in vertical annular two-phase flow, Nucl. Eng. Design, vol. 92, pp , Azzopardi, B. J. and Gibbons, D. B., Annular two-phase flow in a large diameter tube, Chem. Eng., vol. 398, pp , Belt, R. J., Van t Westende, J. M. C., Prasser, H. M., and Portela, L. M., Time and spatially resolved measurements of interfacial waves in vertical annular flow, Int. J. Multiphase Flow, vol. 36, pp , Canny, J., A computational approach to edge detection, IEEE Trans. Pattern Anal. Mach. Intell., vol. PAMI-8, no. 6, pp , Chu, K. J. and Dukler, A. E., Statistical characteristics of thin, wavy films: Part III. Structure of the large waves and their resistance to gas flow, AIChE J., vol. 21, pp , Hagiwara, Y., Miwada, T., and Suzuki, K., Heat transfer and wave structure in the developing region of two-component two-phase annular flow, Phys. Chem. Hydrodyn., vol. 6, pp , Han, H., Zhu, Z., and Gabriel, K., A study on the effect of gas flow rate on the wave characteristics in two-phase gas liquid annular flow, Nucl. Eng. Des., vol. 236, pp , Hewitt, G. F. and Lovegrove, P. C., Frequency and velocity measurements of disturbance waves in annular two-phase flow, UKAEA Report AERE-R4304, Martin, C. J. and Azzopardi, B. J., Waves in vertical annular flow, Phys. Chem. Hydrodyn., vol. 6, pp , Ohba, K. and Nagae, K., Characteristics and behavior of the interfacial wave on the liquid film in a vertically upward air-water two-phase annular flow, Nucl. Eng. Des., vol. 141, pp , Sawant, P., Ishii, M., Hazuku, T., Takamasa, T., and Mori, M., Properties of disturbance waves in vertical annular two-phase flow, Nucl. Eng. Des., vol. 238, pp , Sekoguchi, K., Takeishi, M., and Ishimatsu, T., Interfacial structure in vertical upward annular flow, Phys. Chem. Hydrodyn., vol. 6, pp , Woodmansee, D. E. and Hanratty, T. J., Mechanism for the removal of droplets from a liquid surface by a parallel air flow, Chem. Eng. Sci., vol. 24, pp , Volume 1, Number 2, 2013
AN EXPERIMENTAL INVESTIGATION OF SPILLING BREAKERS
AN EXPERIMENTAL INVESTIGATION OF SPILLING BREAKERS Prof. James H. Duncan Department of Mechanical Engineering University of Maryland College Park, Maryland 20742-3035 phone: (301) 405-5260, fax: (301)
More informationGas-liquid two-phase flow in a downward facing open channel
Computational Methods in Multiphase Flow III 219 Gas-liquid two-phase flow in a downward facing open channel D. Toulouse & L. I. Kiss Département des sciences appliquées, Université du Québec à Chicoutimi,
More informationA study of advection of short wind waves by long waves from surface slope images
A study of advection of short wind waves by long waves from surface slope images X. Zhang, J. Klinke, and B. Jähne SIO, UCSD, CA 993-02, USA Abstract Spatial and temporal measurements of short wind waves
More informationApplication of a borescope to studies of gas liquid flow in downward inclined pipes
International Journal of Multiphase Flow 32 (26) 499 516 www.elsevier.com/locate/ijmulflow Application of a borescope to studies of gas liquid flow in downward inclined pipes E. Roitberg (Trostinetsky),
More informationInfluence of rounding corners on unsteady flow and heat transfer around a square cylinder
Influence of rounding corners on unsteady flow and heat transfer around a square cylinder S. K. Singh Deptt. of Mech. Engg., M. B. M. Engg. College / J. N. V. University, Jodhpur, Rajasthan, India Abstract
More informationIMAGE-BASED STUDY OF BREAKING AND BROKEN WAVE CHARACTERISTICS IN FRONT OF THE SEAWALL
IMAGE-BASED STUDY OF BREAKING AND BROKEN WAVE CHARACTERISTICS IN FRONT OF THE SEAWALL Weijie Liu 1 and Yoshimitsu Tajima 1 This study aims to study the breaking and broken wave characteristics in front
More informationChapter 11 Waves. Waves transport energy without transporting matter. The intensity is the average power per unit area. It is measured in W/m 2.
Energy can be transported by particles or waves: Chapter 11 Waves A wave is characterized as some sort of disturbance that travels away from a source. The key difference between particles and waves is
More informationPressure Sensitive Paint (PSP) / Temperature Sensitive Paint (TSP) Part 1
AerE 545 class notes #12 Pressure Sensitive Paint (PSP) / Temperature Sensitive Paint (TSP) Part 1 Hui Hu Department of Aerospace Engineering, Iowa State University Ames, Iowa 50011, U.S.A Introduction
More informationMeasurement of both gas and liquid velocity profiles for bubble-induced turbulent flow
Measurement of both gas and liquid velocity profiles for bubble-induced turbulent flow H. Takiguchi 1*, M. Furuya 1, T. Arai 1, T. Kanai 1 1: Central research institute of electric power industry (CRIEPI)
More informationet al. [25], Noack et al. [26] for circular cylinder flows, Van Oudheusden [27] for square cylinder and Durgesh [28] for a flat plate model. The first two modes appear as phase-shifted versions of each
More informationFriction properties of the face of a hand-held tennis racket
Available online at www.sciencedirect.com Procedia Engineering 34 (2012 ) 544 549 9 th Conference of the International Sports Engineering Association (ISEA) Friction properties of the face of a hand-held
More informationEXPERIMENTAL INVESTIGATION OF LIQUID HOLDUP IN HORIZONTAL TWO- PHASE ANNULAR FLOW USING CONSTANT ELECTRIC CURRENT METHOD (CECM)
SEMINAR NASIONAL ke-8 Tahun 213 : Rekayasa Teknologi Industri dan Informasi EXPERIMENTAL INVESTIGATION OF LIQUID HOLDUP IN HORIZONTAL TWO- PHASE ANNULAR FLOW USING CONSTANT ELECTRIC CURRENT METHOD (CECM)
More informationA Computational Assessment of Gas Jets in a Bubbly Co-Flow 1
A Computational Assessment of Gas Jets in a Bubbly Co-Flow 1 Melissa Fronzeo*, 1 Michael Kinzel 1 The Pennsylvania State University, University Park, PA, USA Abstract In this effort, Computational Fluid
More informationLASER INDUCED FLUORESCENCE MEASUREMENTS OF CARBON DIOXIDE DISSOLUTION IN WAVE-BREAKING TURBULENCE
LASER INDUCED FLUORESCENCE MEASUREMENTS OF CARBON DIOXIDE DISSOLUTION IN WAVE-BREAKING TURBULENCE Yasunori Watanabe 1, Junichi Otsuka 2 and Ayumi Saruwatari 3 Spatial distributions of dissolved carbon
More informationTechnical Note. Determining the surface tension of liquids by measurements on pendant drops
Technical Note Pendant Drop Measurements Technical note: TN316e Industry section: all Author: FT, TW Date: 12/2010 Method: Drop Shape Analyzer DSA100 Keywords: Methods, surface tension, interfacial tension,
More informationWalking with coffee: when and why coffee spills
Walking with coffee: when and why coffee spills Hans C. Mayer and Rouslan Krechetnikov Department of Mechanical Engineering University of California at Santa Barbara February 20-24, 2012 Page 1/25 Motivation
More informationLesson 14: Simple harmonic motion, Waves (Sections )
Circular Motion and Simple Harmonic Motion The projection of uniform circular motion along any ais (the -ais here) is the same as simple harmonic motion. We use our understanding of uniform circular motion
More informationChapter 11 Waves. Waves transport energy without transporting matter. The intensity is the average power per unit area. It is measured in W/m 2.
Chapter 11 Waves Energy can be transported by particles or waves A wave is characterized as some sort of disturbance that travels away from a source. The key difference between particles and waves is a
More informationWave phenomena in a ripple tank
Wave phenomena in a ripple tank LEP Related topics Generation of surface waves, propagation of surface waves, reflection of waves, refraction of waves, Doppler Effect. Principle Water waves are generated
More informationEffect of 180 bends on gas/liquid flows in vertical upward and downward pipes
Computational Methods in Multiphase Flow VII 435 Effect of 180 bends on gas/liquid flows in vertical upward and downward pipes A. Almabrok, L. Lao & H. Yeung Department of Offshore, Process and Energy
More informationLIFE TIME OF FREAK WAVES: EXPERIMENTAL INVESTIGATIONS
Proceedings of the 6 th International Conference on the Application of Physical Modelling in Coastal and Port Engineering and Science (Coastlab16) Ottawa, Canada, May 10-13, 2016 Copyright : Creative Commons
More informationExperimental study on path instability of rising bubbles
Experimental study on path instability of rising bubbles V. MOTURI, D. FUNFSCHILLING, J. DUSEK ICube, UMR 7357 Mécanique des fluids,2 rue Boussingault,67000,Strasbourg,France. viswa-maitreyi.moturi@etu.unistra.fr
More informationVisual Observation of Nucleate Boiling and Sliding Phenomena of Boiling Bubbles on a Horizontal Tube Heater
Proceedings of the 2 nd World Congress on Mechanical, Chemical, and Material Engineering (MCM'16) Budapest, Hungary August 22 23, 216 Paper No. HTFF 146 DOI:.11159/htff16.146 Visual Observation of Nucleate
More informationDevelopment of High-speed Gas Dissolution Device
Development of High-speed Gas Dissolution Device Yoichi Nakano*, Atsushi Suehiro**, Tetsuhiko Fujisato***, Jun Ma**** Kesayoshi Hadano****, Masayuki Fukagawa***** *Ube National College of Technology, Tokiwadai
More informationISOLATION OF NON-HYDROSTATIC REGIONS WITHIN A BASIN
ISOLATION OF NON-HYDROSTATIC REGIONS WITHIN A BASIN Bridget M. Wadzuk 1 (Member, ASCE) and Ben R. Hodges 2 (Member, ASCE) ABSTRACT Modeling of dynamic pressure appears necessary to achieve a more robust
More informationINTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK
INTERACTION BETWEEN WIND-DRIVEN AND BUOYANCY-DRIVEN NATURAL VENTILATION Bo Wang, Foster and Partners, London, UK ABSTRACT Ventilation stacks are becoming increasingly common in the design of naturally
More informationThe effect of two inclined circular plunging jets on air entrainment in an aeration tank
Computational Methods in Multiphase Flow III 229 The effect of two inclined circular plunging jets on air entrainment in an aeration tank M. S. Baawain, M. Gamal El-Din & D. W. Smith Department of Civil
More informationAerodynamic Analysis of a Symmetric Aerofoil
214 IJEDR Volume 2, Issue 4 ISSN: 2321-9939 Aerodynamic Analysis of a Symmetric Aerofoil Narayan U Rathod Department of Mechanical Engineering, BMS college of Engineering, Bangalore, India Abstract - The
More informationExperimental investigation on air entrainment below impinging jets by means of video observations and image processing
Computational Methods in Multiphase Flow V 481 Experimental investigation on air entrainment below impinging jets by means of video observations and image processing D. V. Danciu, M. J. da Silva, M. Schmidtke,
More informationUnit 7: Waves and Sound
Objectives Unit 7: Waves and Sound Identify the crest, trough, wavelength, and amplitude of any wave, and distinguish transverse and longitudinal wages. Given two of the following quantities of a wave,
More informationFigure 2: Principle of GPVS and ILIDS.
Summary Bubbly flows appear in many industrial applications. In electrochemistry, bubbles emerge on the electrodes in e.g. hydrolysis of water, the production of chloride and as a side-reaction in metal
More informationAtmospheric Waves James Cayer, Wesley Rondinelli, Kayla Schuster. Abstract
Atmospheric Waves James Cayer, Wesley Rondinelli, Kayla Schuster Abstract It is important for meteorologists to have an understanding of the synoptic scale waves that propagate thorough the atmosphere
More informationThe Effect of Von Karman Vortex Street on Building Ventilation
The Effect of Von Karman Vortex Street on Building Ventilation P.Praveen Kumar Abstract This paper deals with the utilisation of the von Karman vortex street principle to maximise air flow into buildings.
More informationOPENINGS AND REINFORCEMENTS 26
ASME BPVC.VIII.1-2015 UG-35.2 UG-36 (4) It is recognized that it is impractical to write requirements to cover the multiplicity of devices used for quick access, or to prevent negligent operation or the
More informationLaser-Induced Bubbles in Glycerol-Water Mixtures
Laser-Induced Bubbles in Glycerol-Water Mixtures Allison R. McCarn, Erin M. Englert, and Gary A. Williams Department of Physics and Astronomy, University of California, Los Angeles, California 90095, USA
More informationSome Geometric and Kinematics Properties of Breaking Waves
Some Geometric and Kinematics Properties of Breaking Waves Pierre Bonmarin Institut de Recherche sur les Phénomènes Hors Equilibre (IRPHE), Laboratoire IOA, 163 Avenue de Luminy, Case 903, 13288 Marseilles,
More informationGerald D. Anderson. Education Technical Specialist
Gerald D. Anderson Education Technical Specialist The factors which influence selection of equipment for a liquid level control loop interact significantly. Analyses of these factors and their interactions
More informationIrrigation &Hydraulics Department lb / ft to kg/lit.
CAIRO UNIVERSITY FLUID MECHANICS Faculty of Engineering nd Year CIVIL ENG. Irrigation &Hydraulics Department 010-011 1. FLUID PROPERTIES 1. Identify the dimensions and units for the following engineering
More informationThe Study of Bubbly Gas-Water Flow Using
The Study of Bubbly Gas-Water Flow Using Displacement Current Phase Tomography Chris Zuccarelli 1, Benjamin Straiton 1, Joshua Sines 1, Qussai Marashdeh 1 1 Tech4Imaging, 1910 Crown Park Court, Columbus,
More informationUsing an Adaptive Thresholding Algorithm to Detect CA1 Hippocampal Sharp Wave Ripples. Jay Patel. Michigan State University
Using an Adaptive Thresholding Algorithm to Detect CA1 Hippocampal Sharp Wave Ripples Jay Patel Michigan State University Department of Physics and Astronomy, University of California, Los Angeles 2013
More informationErmenek Dam and HEPP: Spillway Test & 3D Numeric-Hydraulic Analysis of Jet Collision
Ermenek Dam and HEPP: Spillway Test & 3D Numeric-Hydraulic Analysis of Jet Collision J.Linortner & R.Faber Pöyry Energy GmbH, Turkey-Austria E.Üzücek & T.Dinçergök General Directorate of State Hydraulic
More informationAn experimental study of internal wave generation through evanescent regions
An experimental study of internal wave generation through evanescent regions Allison Lee, Julie Crockett Department of Mechanical Engineering Brigham Young University Abstract Internal waves are a complex
More informationAn innovative technology for Coriolis metering under entrained gas conditions
An innovative technology for Coriolis metering under entrained gas conditions Coriolis mass flowmeters are usually only used for single-phase fluids, i.e. either liquids or gases, since it has been found
More informationLab 4: Pressure Gradients over a Wing
2009 Lab 4: Pressure Gradients over a Wing Innovative Scientific Solutions Inc. 2766 Indian Ripple Road Dayton, OH 45440 (937)-429-4980 Lab 4: Pressure Gradients over a Wing Introduction: Like the previous
More informationThe Split of Two-Phase-Flow at Horizontal Side-T-junctions in Unbalanced Pipe Systems for Clean Extinguishing Agents
The Split of Two-Phase-Flow at Horizontal Side-T-junctions in Unbalanced Pipe Systems for Clean Extinguishing Agents Abstract by Gudrun Fay Minimax GmbH & CO. KG Industriestraße 10-12, 23840 Bad Oldesloe,
More informationVortical motions under short wind waves
Vortical motions under short wind waves X. Zhang and C. S. Cox Scripps Institution of Oceanography, UCSD, CA 9293-23, USA Abstract The flow structures under ocean wind waves are of great significance in
More informationQuantification of the Effects of Turbulence in Wind on the Flutter Stability of Suspension Bridges
Quantification of the Effects of Turbulence in Wind on the Flutter Stability of Suspension Bridges T. Abbas 1 and G. Morgenthal 2 1 PhD candidate, Graduate College 1462, Department of Civil Engineering,
More informationAERODYNAMIC CHARACTERISTICS OF NACA 0012 AIRFOIL SECTION AT DIFFERENT ANGLES OF ATTACK
AERODYNAMIC CHARACTERISTICS OF NACA 0012 AIRFOIL SECTION AT DIFFERENT ANGLES OF ATTACK SUPREETH NARASIMHAMURTHY GRADUATE STUDENT 1327291 Table of Contents 1) Introduction...1 2) Methodology.3 3) Results...5
More informationNumerical Analysis of Two Phase Flow Patterns in Vertical and Horizontal Pipes
Numerical Analysis of Two Phase Flow Patterns in Vertical and Horizontal Pipes MOHAMMED A. ABDULWAHID, HASANAIN J. KAREEM, MUJTABA A. ALMUDHAFFAR Thermal Mechanical Engineering, Southern Technical University,
More informationAir Bubble Defects in Dispensing Nanoimprint Lithography
Air Bubble Defects in Dispensing Nanoimprint Lithography Abstract We report a theoretical study and dynamic simulation to understand the dynamic behavior of the air bubble defects in Dispensing Nanoimprint
More informationAIR-WATER FLOW STRUCTURES AT AN ABRUPT DROP WITH SUPERCRITICAL FLOW
AIR-WATER FLOW STRUCTURES AT AN ABRUPT DROP WITH SUPERCRITICAL FLOW H. CHANSON and L. TOOMBES Department of Civil Engineering, The University of Queensland, Brisbane QLD 4072, Australia 1. Introduction
More informationExperimental Studies on the Instabilities of Viscous Fingering in a Hele-Shaw Cell
Korean J. Chem. Eng., 17(2), 169-173 (2000) Experimental Studies on the Instabilities of Viscous Fingering in a Hele-Shaw Cell Chung Gi Baig, Young Ho Chun*, Eun Su Cho* and Chang Kyun Choi School of Chemical
More informationPendant Drop Measurements
KRÜSS pplication Note TN316d Page 1 Pendant Drop Measurements pplication note: TN316d Industry section: all uthor: Dr. Tobias Winkler Date: December 2010 Method: Drop Shape nalysis System DS100 Drop Shape
More informationEVALUATION OF ENVISAT ASAR WAVE MODE RETRIEVAL ALGORITHMS FOR SEA-STATE FORECASTING AND WAVE CLIMATE ASSESSMENT
EVALUATION OF ENVISAT ASAR WAVE MODE RETRIEVAL ALGORITHMS FOR SEA-STATE FORECASTING AND WAVE CLIMATE ASSESSMENT F.J. Melger ARGOSS, P.O. Box 61, 8335 ZH Vollenhove, the Netherlands, Email: info@argoss.nl
More informationResults and Discussion for Steady Measurements
Chapter 5 Results and Discussion for Steady Measurements 5.1 Steady Skin-Friction Measurements 5.1.1 Data Acquisition and Reduction A Labview software program was developed for the acquisition of the steady
More informationYasuyuki Hirose 1. Abstract
Study on Tsunami force for PC box girder Yasuyuki Hirose 1 Abstract In this study, a waterway experiment was performed in order to understand the influence of tsunami forms on tsunami forces acting on
More informationWaves. harmonic wave wave equation one dimensional wave equation principle of wave fronts plane waves law of reflection
Waves Vocabulary mechanical wave pulse continuous periodic wave amplitude wavelength period frequency wave velocity phase transverse wave longitudinal wave intensity displacement wave number phase velocity
More informationThe effect of back spin on a table tennis ball moving in a viscous fluid.
How can planes fly? The phenomenon of lift can be produced in an ideal (non-viscous) fluid by the addition of a free vortex (circulation) around a cylinder in a rectilinear flow stream. This is known as
More informationTHREE DIMENSIONAL STRUCTURES OF FLOW BEHIND A
The Seventh Asia-Pacific Conference on Wind Engineering, November 8-12, 29, Taipei, Taiwan THREE DIMENSIONAL STRUCTURES OF FLOW BEHIND A SQUARE PRISM Hiromasa Kawai 1, Yasuo Okuda 2 and Masamiki Ohashi
More information4.4 WAVE CHARACTERISTICS 4.5 WAVE PROPERTIES Student Notes
4.4 WAVE CHARACTERISTICS 4.5 WAVE PROPERTIES Student Notes I. DIFFERENT TYPES OF WAVES A. TRANSVERSE AND LONGITUDINAL WAVES B. WAVE PULSES AND TRAVELLING WAVES C. SOUND AND WATER WAVES II. DEFINING TERMS
More informationFree Surface Flow Simulation with ACUSIM in the Water Industry
Free Surface Flow Simulation with ACUSIM in the Water Industry Tuan Ta Research Scientist, Innovation, Thames Water Kempton Water Treatment Works, Innovation, Feltham Hill Road, Hanworth, TW13 6XH, UK.
More informationUNIT 15 WATER HAMMER AND SURGE TANKS
UNT 15 WATER HAMMER AND SURGE TANKS Structure 15.1 ntroduction Objectives 15.2 Water Hammer 15.2.1 Expression for Rise in Pressure 15.3 Rapid Acceleration of Flow 15.4 Surge Tanks 15.5 Summary 15.6 Keywords
More informationLab # 03: Visualization of Shock Waves by using Schlieren Technique
AerE545 Lab # 03: Visualization of Shock Waves by using Schlieren Technique Objectives: 1. To get hands-on experiences about Schlieren technique for flow visualization. 2. To learn how to do the optics
More informationI.CHEM.E. SYMPOSIUM SERIES NO. 97 BUOYANCY-DRIVEN NATURAL VENTILATION OP ENCLOSED SPACES
BUOYANCY-DRIVEN NATURAL VENTILATION OP ENCLOSED SPACES M. R. Marshall* and P. L. Stewart-Darling* A simple mathematical model for the buoyancy driven ventilation of an enclosed space, using a two-pipe
More informationCavitation Bubbles in a Starting Submerged Water Jet
CAV21:sessionA7.5 1 Cavitation Bubbles in a Starting Submerged Water Jet K.Nakano, M.Hayakawa, S.Fujikawa and T.Yano Graduate School of Engineering, Hokkaido University, Sapporo, Japan Abstract The behavior
More informationESCI 343 Atmospheric Dynamics II Lesson 10 - Topographic Waves
ESCI 343 Atmospheric Dynamics II Lesson 10 - Topographic Waves Reference: An Introduction to Dynamic Meteorology (3 rd edition), J.R. Holton Reading: Holton, Section 7.4. STATIONARY WAVES Waves will appear
More informationWave Motion. interference destructive interferecne constructive interference in phase. out of phase standing wave antinodes resonant frequencies
Wave Motion Vocabulary mechanical waves pulse continuous periodic wave amplitude period wavelength period wave velocity phase transverse wave longitudinal wave intensity displacement amplitude phase velocity
More informationVORTEX SHEDDING AND VORTEX FORMATION FROM A PAIR OF IN-LINE FORCED OSCILLATING TANDEM ARRANGED CIRCULAR CYINDERS IN A UNIFORM FLOW
5 th International Symposium on Flow Visualization June 5-8,, Minsk, Belarus VORTEX SHEDDING AND VORTEX FORMATION FROM A PAIR OF IN-LINE FORCED OSCILLATING TANDEM ARRANGED CIRCULAR CYINDERS IN A UNIFORM
More informationInvestigation of Suction Process of Scroll Compressors
Purdue University Purdue e-pubs International Compressor Engineering Conference School of Mechanical Engineering 2006 Investigation of Suction Process of Scroll Compressors Michael M. Cui Trane Jack Sauls
More informationMeasurement of Bubble Velocity using Spatial Filter Velocimetry
Lisbon, Portugal, 9 July, Measurement of Bubble Velocity using Spatial Filter Velocimetry Takaaki Matsumoto, Shigeo Hosokawa,*, Akio Tomiyama : Graduate School of Engineering, Kobe University, Kobe, Japan
More informationAIR EJECTOR WITH A DIFFUSER THAT INCLUDES BOUNDARY LAYER SUCTION
Engineering MECHANICS, Vol. 20, 2013, No. 3/4, p. 213 220 213 AIR EJECTOR WITH A DIFFUSER THAT INCLUDES BOUNDARY LAYER SUCTION Václav Dvořák* The article deals with axial-symmetric subsonic air-to-air
More informationPre AP Physics: Unit 7 Vibrations, Waves, and Sound. Clear Creek High School
Pre AP Physics: Unit 7 Vibrations, Waves, and Sound Clear Creek High School Simple Harmonic Motion Simple Harmonic Motion Constant periodic motion of an object. An object oscillates back and forth along
More informationSIMULATION OF ENTRAPMENTS IN LCM PROCESSES
Douai, FRANCE - July 6 SIMULATION OF ENTRAPMENTS IN LCM PROCESSES René Arbter, Paolo Ermanni Centre of Structure Technologies ETH Zurich, Leonhardstr. 7, 89 Zurich, Switzerland: rarbter@ethz.ch ABSTRACT:
More informationSimulation of Gas Holdup in a Bubble Column with a Draft Tube for Gas Dispersion into an Annulus
Simulation of Gas Holdup in a Bubble Column with a Draft Tube for Gas Dispersion into an Annulus Fukuji Yamashita Dept. of Applied Bioscience, Kanagawa Institute of Technology, Atsugi 243-292, Japan, yamasita@bio.kanagawa-it.ac.jp
More informationANALYSIS OF AERODYNAMIC CHARACTERISTICS OF A SUPERCRITICAL AIRFOIL FOR LOW SPEED AIRCRAFT
ANALYSIS OF AERODYNAMIC CHARACTERISTICS OF A SUPERCRITICAL AIRFOIL FOR LOW SPEED AIRCRAFT P.Sethunathan 1, M.Niventhran 2, V.Siva 2, R.Sadhan Kumar 2 1 Asst.Professor, Department of Aeronautical Engineering,
More informationAIS data analysis for vessel behavior during strong currents and during encounters in the Botlek area in the Port of Rotterdam
International Workshop on Next Generation Nautical Traffic Models 2013, Delft, The Netherlands AIS data analysis for vessel behavior during strong currents and during encounters in the Botlek area in the
More informationEXPERIMENTAL RESULTS OF GUIDED WAVE TRAVEL TIME TOMOGRAPHY
18 th World Conference on Non destructive Testing, 16-20 April 2012, Durban, South Africa EXPERIMENTAL RESULTS OF GUIDED WAVE TRAVEL TIME TOMOGRAPHY Arno VOLKER 1 and Hendrik VOS 1 TNO, Stieltjesweg 1,
More informationFlow transients in multiphase pipelines
Flow transients in multiphase pipelines David Wiszniewski School of Mechanical Engineering, University of Western Australia Prof. Ole Jørgen Nydal Multiphase Flow Laboratory, Norwegian University of Science
More informationCOURSE NUMBER: ME 321 Fluid Mechanics I Fluid statics. Course teacher Dr. M. Mahbubur Razzaque Professor Department of Mechanical Engineering BUET
COURSE NUMBER: ME 321 Fluid Mechanics I Fluid statics Course teacher Dr. M. Mahbubur Razzaque Professor Department of Mechanical Engineering BUET 1 Fluid statics Fluid statics is the study of fluids in
More informationA model for the bubble lift-off diameter in subcooled boiling flow in a horizontal channel
Advances in Fluid Mechanics X 215 A model for the bubble lift-off diameter in subcooled boiling flow in a horizontal channel S. Shabannejad & N. Ashgriz Department of Mechanical and Industrial Engineering,
More informationFLUID FORCE ACTING ON A CYLINDRICAL PIER STANDING IN A SCOUR
BBAA VI International Colloquium on: Bluff Bodies Aerodynamics & Applications Milano, Italy, July, 20-24 2008 FLUID FORCE ACTING ON A CYLINDRICAL PIER STANDING IN A SCOUR Takayuki Tsutsui Department of
More informationVariation in Pressure in Liquid-Filled Plastic Film Bags Subjected to Drop Impact
Materials Transactions, Vol. 53, No. 2 (12) pp. 291 to 295 Special Issue on APCNDT 9 12 The Japanese Society for Non-Destructive Inspection Variation in Pressure in Liquid-Filled Plastic Film Bags Subjected
More informationWind tunnel effects on wingtip vortices
48th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition 4-7 January 2010, Orlando, Florida AIAA 2010-325 Wind tunnel effects on wingtip vortices Xin Huang 1, Hirofumi
More informationNATURE AND PROPERTIES OF WAVES P.1
NATURE AND ROERTIES OF WAVES.1 DSE AER IA 218 14. Which of the following statements about waves is/are correct? (1) Longitudinal waves can transmit energy from one place to another but transverse waves
More informationInstallation Effects on Ultrasonic Flow Meters for Liquids. Jan Drenthen - Krohne
Installation Effects on Ultrasonic Flow Meters for Liquids Jan Drenthen - Krohne Jan G. Drenthen & Pico Brand ALTOSONIC 5 Installation effects on ultrasonic flow meters for liquids 1. Introduction 2. Meter
More informationSound scattering by hydrodynamic wakes of sea animals
ICES Journal of Marine Science, 53: 377 381. 1996 Sound scattering by hydrodynamic wakes of sea animals Dmitry A. Selivanovsky and Alexander B. Ezersky Selivanovsky, D. A. and Ezersky, A. B. 1996. Sound
More informationDynamics of bubble rising at small Reynolds numbers
MATEC Web of Conferences 3, 01004 ( 015) DOI: 10.1051/ matecconf/ 015301004 C Owned by the authors, published by EDP Sciences, 015 Dynamics of bubble rising at small Reynolds numbers Vladimir Arkhipov
More informationKeywords: dynamic stall, free stream turbulence, pitching airfoil
Applied Mechanics and Materials Vol. 225 (2012) pp 103-108 Online available since 2012/Nov/29 at www.scientific.net (2012) Trans Tech Publications, Switzerland doi:10.4028/www.scientific.net/amm.225.103
More informationFluid Flow. Link. Flow» P 1 P 2 Figure 1. Flow Model
Fluid Flow Equipment: Water reservoir, output tubes of various dimensions (length, diameter), beaker, electronic scale for each table. Computer and Logger Pro software. Lots of ice.temperature probe on
More informationNumerical Simulations of a Train of Air Bubbles Rising Through Stagnant Water
Numerical Simulations of a Train of Air Bubbles Rising Through Stagnant Water Hong Xu, Chokri Guetari ANSYS INC. Abstract Transient numerical simulations of the rise of a train of gas bubbles in a liquid
More informationWaves. Name and Surname: Class: L E A R N I N G O U T C O M E. What are waves? Why are waves formed?
L E A R N I N G O U T C O M E What are waves? Why are waves formed? Waves Y E A R 1 0, C H A P T E R 8 G J Z A H R A, B. E D ( H O N S ) Why does a pool filled with water look shallower than it really
More informationUndertow - Zonation of Flow in Broken Wave Bores
Nearshore Circulation Undertow and Rip Cells Undertow - Zonation of Flow in Broken Wave Bores In the wave breaking process, the landward transfer of water, associated with bore and surface roller decay
More informationWIND-INDUCED LOADS OVER DOUBLE CANTILEVER BRIDGES UNDER CONSTRUCTION
WIND-INDUCED LOADS OVER DOUBLE CANTILEVER BRIDGES UNDER CONSTRUCTION S. Pindado, J. Meseguer, J. M. Perales, A. Sanz-Andres and A. Martinez Key words: Wind loads, bridge construction, yawing moment. Abstract.
More informationEXPERIMENTAL STUDY ON THE DISCHARGE CHARACTERISTICS OF SLUICE FOR TIDAL POWER PLANT
EXPERIMENTAL STUDY ON THE DISCHARGE CHARACTERISTICS OF SLUICE FOR TIDAL POWER PLANT Sang-Ho Oh 1, Kwang Soo Lee 1 and Dal Soo Lee 1 The discharge characteristics of sluice caisson for tidal power plant
More informationPaper 2.2. Operation of Ultrasonic Flow Meters at Conditions Different Than Their Calibration
Paper 2.2 Operation of Ultrasonic Flow Meters at Conditions Different Than Their Calibration Mr William Freund, Daniel Measurement and Control Mr Klaus Zanker, Daniel Measurement and Control Mr Dale Goodson,
More informationThe Influence of Ocean Surface Waves on Offshore Wind Turbine Aerodynamics. Ali Al Sam
The Influence of Ocean Surface Waves on Offshore Wind Turbine Aerodynamics Ali Al Sam What I m going to wear today? Do I need to leave early to get to work? Taking buss or riding bike? Where will we drink
More informationFlow and Mixing in the Liquid between Bubbles
Excerpt from the Proceedings of the COMSOL Conference 2009 Boston Flow and Mixing in the Liquid between Bubbles Bruce A. Finlayson, Professor Emeritus of Chemical Engineering Department of Chemical Engineering,
More informationEXPERIMENTAL MEASUREMENT OF THE WASH CHARACTERISTICS OF A FAST DISPLACEMENT CATAMARAN IN DEEP WATER
EXPERIMENTAL MEASUREMENT OF THE WASH CHARACTERISTICS OF A FAST DISPLACEMENT CATAMARAN IN DEEP WATER A.F. Molland, P.A. Wilson and D.J. Taunton Ship Science Report No. 124 University of Southampton December
More informationCHAPTER 8: MECHANICAL WAVES TRANSMIT ENERGY IN A VARIETY OF WAYS
CHAPTER 8: MECHANICAL WAVES TRANSMIT ENERGY IN A VARIETY OF WAYS DISCLAIMER FOR MOST QUESTIONS IN THIS CHAPTER Waves are always in motion, as they transmit energy and information from one point to another.
More informationCharacterizers for control loops
Characterizers for control loops By: F. G. Shinskey (May 1999) Introduction Commercial controllers such as the PID series (proportional, integral, derivative, and their combinations) are linear devices
More information