Feasibility study of a semi floating spar buoy wind turbine anchored with a spherical joint to the sea floor
|
|
- Dominick Wiggins
- 6 years ago
- Views:
Transcription
1 Feasibility study of a semi floating spar buoy wind turbine anchored with a spherical joint to the sea floor María Sanz Martínez DTU Wind Energy DK-4000 Roskilde, Denmark msma@dtu.dk Anand Natarajan DTU Wind Energy DK-4000 Roskilde, Denmark anat@dtu.dk Lars Christian Henriksen DTU Wind Energy DK-4000 Roskilde, Denmark larh@dtu.dk Abstract: The feasibility of a semi floating platform offshore wind turbine system is investigated at 120m water depth. The semi floating system consists of a 5MW wind turbine on a floater with mooring lines similar to a spar buoy and strongly anchored with a spherical joint to the sea soil. The stability of the newly designed floater and mooring assembly are analyzed from static and dynamic simulations. The design loads on the universal joint on the sea floor are tuned with the needs for a ballast chamber. Using load simulation in the HAWC2 software, ultimate and equivalent fatigue loads are obtained and compared with the loads from the same wind turbine mounted on a spar buoy system and a land based wind turbine at the same points. The results show a decrement in the ultimate and equivalent fatigue loads for the new system. Keywords: Design loads, spherical joint, semi floating platform, mooring system 1. Introduction Fixed offshore wind turbine structures may be cost effective till 60 metres water depth. Monopile fixed sub structures are usually used in wind turbine installations till 30m water depths and frame structures till 60m. Floating wind turbine prototypes are designed for water depths near 150m-200m. Therefore, the wind industry may require other designs of cost effective sub structures in the range of metres. A floating spar-buoy substructure which is anchored with a universal spherical joint to the sea soil is analyzed at 120m water depth as potential solution for moderate water depths (60m to120m). Oil industry has used similar substructures [1]. However, the wind loads experienced by the oil rig structures are negligible compared to the rotor generated dynamic loads experienced by wind turbines so a further study is required. In this study, the wind turbine used is the NREL 5 MW [2]. The simulations were performed in the aero-hydro-servo-elastic code HAWC2 [3]. For a better analogy, the new system was compared with the NREL spar buoy [4] and a land based wind turbine. Hence, the same simulations were run for all systems. 2. Design of the platform and static analysis of the system The new sub structure configuration should achieve static and dynamic stability. Therefore the submerged volume needs to be large enough to equilibrate the system with its restoring force (the higher the angle of tilt, the bigger the submerged volume). To match these requirements, the final geometry was chosen as two cylinders of different radii linked by an interface with the shape of a truncated cone (see Figure 1). The design of the new platform was obtained through an iterative optimization process between the total weight of the system and the submerged volume under normal conditions. In each iteration, the weight of the system was determined and then, the submerged volume needed to stabilize that weight was computed. We considered the weight for the initial iteration as the weight of the spar buoy system. The final mass of the platform was seven times lower than the mass of the spar buoy floater because there is no 1
2 ballast requirement in the semi floating system. The final geometry of the floater consists in: a bottom cylindrical part of 80 m length and 2 m radius, a transition conical part of 40 m length, and a top cylindrical part of 10 m length and 3 m radius. The total draft of the platform is 130 m; the floater is designed for a water depth of 120 m. As the floater was redesigned, the Morison equation applicability was verified with 8 different significant wave heights. A stability analysis using two tools was performed: an approximate Matlab script that considers the weight, buoyancy and thrust loads and calculates the pitch angle of equilibrium of the platform; and detailed HAWC2 simulations that includes also the mooring line dynamics and hydrodynamics. The results of both analyses are listed in Table 1. Table 1 Platform equilibrium angle of both systems depending on wind speed Pitch angle Pitch angle Mean Wind (Matlab) (HAWC2) speed [m/s] [deg] [deg] Table 2 Natural frequencies of the semi floating system Frequency [Hz] Description Platform roll Platform pitch Platform yaw These results are within the same range of the natural frequencies calculated for the spar buoy system in other studies as [5]. The floater is depicted in Figure 1. The largest pitch angle is obtained for mean wind speeds close to the rated wind speed because the thrust force is the main input of the system. The mooring line forces cause the different equilibrium angles of both analyses. This shows the system is statically stable without mooring system, but the resultant equilibrium angle is too high to be operative. Mooring lines should be considered, and designed for improved performance. A modal analysis was then performed to obtain the lowest modes of the static system. The results are listed in Table 2: Figure 1 Sketch of the floater with a universal joint at the soil 2
3 3. Specification of new mooring system We defined a new mooring system based on [6]. Each mooring line is divided into a number of elements or Timoshenko bodies that are analyzed individually together with the rest of the system in HAWC2. The equation of motion for each of the mooring bodies is: JONSWAP (Joint North Sea Wave Project) Spectrum [7] with an irregular airy pattern. The peak enhancement factor, γ was assumed to have a constant value of 3.3. The significant height and the period of the waves are defined in Figure 3. ( ) ( ) ( ) ( ) The main parameters of the mooring system are presented in Table 3. The mooring system uses catenary lines because it has simple and cheap anchors, it is easy to install and it is suitable for shallower waters. Its sketch can be seen in Figure 2. Table 3 Summary of properties of the mooring system Number of mooring lines 3 Depth to fairleads, anchors Radius to fairleads, anchors Un stretched line length Line diameter Line mass density (in air) Line mass density (in water) 30, 120 m 9.4, 850 m 853 m 0.1 m kg/m kg/m Figure 3 Wave parameters depending on the mean wind speed. We define semi floating system as the 5 MW NREL wind turbine defined in [2], mounted on the platform described in section 2 and the mooring system defined in section 3. To confirm the good operation of the semi floating system the mean power and thrust are compared with the corresponding figures for the floating spar buoy mounted wind turbine in Figure 4 to Figure 7. Line extensional stiffness kn Figure 2 Mooring system scheme. 4. Wind Turbine System and Environment Environment definition The wave conditions for the aeroelastic simulations were defined following the Figure 4 Power curve comparison. 3
4 wind turbine and for a land based wind turbine. The response at the tower top for a single degree of freedom system is ( ) { ( ) ) ( ) ( ( ) Figure 5 Thrust curve comparison. The tower top displacement was fitted to the previous equation and the system parameters were calculated: The mass used in each case was the whole system mass (tower, nacelle, rotor and floater). The obtained results were: Table 4 Comparison of damping values Semi floating system Spar buoy system Land based system Figure 6 Pitch curve comparison. ξ c [kns/m] k [kn/m] The design load cases 1.1 (NTM, normal turbulence model) and 1.3 (ETM, extreme turbulence model) from the standard IEC 64100:3 [8] are simulated. Both design load cases use 6 different wind turbulence seeds for each mean wind speed. 5. Fatigue analysis Figure 7 Rotational speed curve comparison. The differences are minimal. Estimated damping for the pitch of the platform We consider the semi floating system as a second order system to estimate its damping. In the steady state, the response of the system to a step force was simulated. The same test was completed for the spar buoy For the site we assumed the mean wind speed has a Rayleigh distribution with a scale parameter σ = 6.80 (data from [9]). A yaw misalignment angle of ± 10 degrees is included 50% of the simulated time (25% each) in the normal turbulence model simulations. In this study, the fatigue analysis was used as a methodology to compare the dynamic loads on both systems (spar buoy and semi floating) in the bottom of the tower. For a better comparison, a third system, a land based 4
5 wind turbine, was simulated and compared together with the semi floating and the spar buoy system. In the analysis of the semi floating system, the joint was also studied as a point of interest, whose lifetime loads should be used as guidelines in the design of the joint. Figure 8 shows the fatigue damage equivalent loads for the fore-aft bending moment (M x ) at the bottom of the tower (lowest node of the tower). The semi floating system obtained results within the same range of the land based wind turbine, while the spar buoy reached higher equivalent loads. These results were due to higher platform pitch oscillations for the spar buoy system compared with the oscillations of the semi floating system for the same angle. The reason for the high differences is the semi floating system has only positive bending foreaft moments and this has a lower contribution on the fatigue loads (see Figure 9). At high wind speeds, the semi floating system reached lower negative moments in comparison to the land turbine. Figure 10 shows the fatigue loads for the side to side bending moment (M y ) in the bottom of the tower. The semi floating system obtained lower loads for high wind speeds than both the land based and the spar buoy systems due to the lower variations in the amplitude of the loads than for the other systems (in Figure 11 it is noticeable the lower values of the standard deviation for the semi floating and land based systems). For low wind speeds the spar buoy system reaches high equivalent fatigue loads while the semi floating and the land based systems have loads in the same range. For the torsional moment at the bottom of the tower (M z ), the semi floating system achieved lower equivalent loads compared with the other two systems, which was again due to the lower standard deviation of loads on the semi floating system (Figure 12 and Figure 13). The equivalent lifetime loads for the three systems are listed in Table 5 (the lifetime of the turbine is assumed as 20 years of operation 10 7 cycles). Table 5 Equivalent fatigue loads in the tower bottom [knm] Semi Float Spar Buoy Land Based M x M y M z The ratios between the results obtained for the sea turbines and the land turbine have been compared with previous studies in this field ( [10] and [11]) obtaining similar results to previous publications. Figure 8 Equivalent for aft fatigue loads M x at the tower bottom (continuous line: no yaw misalignment; dotted line: -10⁰ yaw misalignment; dashed line: +10⁰ yaw misalignment). Figure 9 Statistical data of the NTM simulations for the M x loads at the tower bottom (Max maximum value; Min - minimum value; Mean - averaged value; SF 5
6 semi floating system, SB spar buoy system, Land- land based system). yaw misalignment; dotted line: -10⁰ yaw misalignment; dashed line: +10⁰ yaw misalignment). Figure 10 Equivalent side to side fatigue loads M y at the tower bottom (continuous line: no yaw misalignment; dotted line: -10⁰ yaw misalignment; dashed line: +10⁰ yaw misalignment). Figure 13 Statistical data of the NTM simulations for the M z loads at the tower bottom (Max maximum value; Min - minimum value; Mean - averaged value; SF semi floating system, SB spar buoy system, Land- land based system). At the joint (Figure 14 to Figure 16), the maximum equivalent loads were obtained in the wind and waves direction (y). In the other axis, the changes in the forces were minor, so the equivalent fatigue loads were smaller. The equivalent fatigue loads at the joint for the semi floating system are listed in Table 6: Figure 11 - Statistical data of the NTM simulations for the M y loads at the tower bottom (Max maximum value; Min - minimum value; Mean - averaged value; SF semi floating system, SB spar buoy system, Land- land based system). Table 6 Equivalent fatigue lifetime loads in the joint (semi floating system) Load Direction Equivalent fatigue lifetime load (kn) F x 664 F y 1128 F z 665 Figure 12 Equivalent torsional fatigue loads M z at the tower bottom (continuous line: no 6
7 from the ETM simulations (DLC 1.3). For the second method utilized, the NTM simulations were used. The threshold was defined as Where µ and σ are the mean and the standard deviation of the NTM simulations. All the peaks above the threshold were considered. Their average value was calculated and multiplied by 1.35 to obtain the ultimate load expected for each wind speed. Figure 14 Equivalent lateral fatigue loads at the joint (F x ). Figure 15 Equivalent longitudinal fatigue loads at the joint (F y ). Again, for a better analysis, the three systems -semi floating, spar buoy and land basedwere compared. Figure 17 shows the ultimate loads at the tower bottom fore aft bending moment (M x ) for the semi floating system. They reached their maximum around rated wind speed (due to the maximum thrust). The spar buoy system obtained higher ultimate loads than the other systems because of isolated extremes. Even though the mean values obtained for the three systems were quite similar, their standard deviations differed for high wind speeds (see Figure 18). Figure 19 shows the ultimate loads of the three systems for the case of the side to side tower bottom side to side moment (M y ). The semi floating system obtained lower loads than the other two systems. For the case of the torsional bending moment at the bottom of the tower (M z ), the semi floating system obtained the lowest ultimate loads (see Figure 20). Figure 16 Equivalent vertical fatigue loads at the joint (F z ). 6. Ultimate load analysis The ultimate loads analysis is done according to two different methods described in the IEC standards [8] and [12]. The first method used was simply extracting the maximum values Figure 17 Ultimate loads for fore aft bending moment (M x ) at the tower bottom (SF semi floating system, SB spar buoy system, Land- land based system). 7
8 to the high thrust force obtained at rated wind speed. To decrease the values achieved in Figure 23 (vertical force at the joint), ballast could be added to the floater. Figure 18 Standard deviation of the fore aft bending moment (M x ) at the tower bottom (SF semi floating system, SB spar buoy system, Land- land based system). Figure 21 Ultimate lateral loads at the joint (F x ). Figure 19 Ultimate loads for side to side bending moment (M y ) at the tower bottom (SF semi floating system, SB spar buoy system, Land- land based system). Figure 22 Ultimate longitudinal loads at the joint (F y ). Figure 20 Ultimate loads for torsional bending moment (M z ) at the tower bottom (SF semi floating system, SB spar buoy system, Land- land based system). At the joint of the semi floating system (Figure 21 to Figure 23) the maximum loads were reached around rated wind speed. This is due Figure 23 Ultimate vertical loads at the joint (F z ). 7. Conclusions The semi floating system is a promising solution for moderate water depths. The 8
9 oscillations of the semi floating system under turbulent wind excitation are much lower than the spar buoy. The pitch angle of the platform is steadier and has lower oscillations against possible excitations and that reduces the fatigue loads considerably. According to the results of the fatigue analysis (Table 5) the semi floating system expects significantly lower damage equivalent loads than the spar buoy system. This means that the structural requirements are less demanding and, more likely, cheaper than for the spar buoy system. The design of the joint should be carefully evaluated and consider the impact of the fatigue loads depicted in Table 6 and the ultimate loads displayed in Figure 21 to Figure 23. The ultimate loads analysis shows that at the tower bottom, the maximum loads obtained for the semi floating system are lower at almost all wind speeds than for the spar buoy wind turbine. Further analysis should be done to verify the feasibility of this new semi floating system. Acknowledgement The work presented in this paper is part of the Collaborative Project "INNWIND.EU" supported by the EU Seventh Framework Program (FP7), grant no The financial support is greatly appreciated. References 1. Glanville RS, Paulling JR, Halkyard JE, Lehtinen TJ. Analysis of the Spar Floating Drilling Production and Storage Structure. Offshore Technology Conference (OTC-6701) May 1991, pp Jonkman J, Butterfield S, Scott G. Definition of a 5-MW reference wind turbine for offshore system development. NREL. February 2009.NREL/TP Larsen TJ, Hansen AM. How 2 HAWC2, the user's manual. Risø National Laboratory 2012 Technical Report R-1597, (ver.4-4). 4. Jonkman J. Definition of the floating system for phase IV of OC3. NREL May 2010 NREL/TP Bir G and Jonkman J. Aeroelastic Instabilities of Large Offshore and Onshore Wind Turbines. Journal of Physics: Conference Series, The Second Conference on The Science of Making Torque From Wind, Copenhagen, Denmark, August 2007, [online journal], Vol. 75, 2007, Hansen AM and Kallesøe BS. Detailed and reduced models of dynamic mooring system. Aeroelastic Optimization of MW Wind Turbines. Risø National Laboratory Risø-R- 1803(EN) 2011; Carter D. Prediction of wave height and period for a constant wind velocity using JONSWAP results. Ocean Engineering vol ; International Electrotechnical Commission. IEC Ed. 1. Wind Turbines Part 3: Design Requirements for Offshore Wind Turbines. Geneva, Switzerland: International Electrotechnical Commission, Bezrukovs V and Bezrukovs V. Wind speed and energy at different heights on the Latvian coast of the Baltic Sea in proceedings of the Conference World Renewable Energy Forum, WREF 2012 May 2012, Denver. 10. Matha D, Jonkman J, Fischer T. Model Development and Loads Analysis of an Offshore Wind Turbine on a Tension Leg Platform, with a Comparison to Other Floating Turbine Concepts. NREL February 2010, NREL/SR Jonkman JM. Dynamics Modeling and Loads Analysis of an Offshore Floating Wind Turbine. NREL November NREL/TP International Electrotechnical Commission. TC88-MT1 (ed.). IEC Ed.3 CD. 2. Revision. Wind Turbines. Part 1: Design Requirements. International Electrotechnical Commission: Geneva, Switzerland,
Computationally Efficient Determination of Long Term Extreme Out-of-Plane Loads for Offshore Turbines
Computationally Efficient Determination of Long Term Extreme Out-of-Plane Loads for Offshore Turbines Anand Natarajan Senior Scientist Wind Energy Department, Risø DTU Denmark Introduction IEC 61400-1
More informationA NOVEL FLOATING OFFSHORE WIND TURBINE CONCEPT: NEW DEVELOPMENTS
A NOVEL FLOATING OFFSHORE WIND TURBINE CONCEPT: NEW DEVELOPMENTS L. Vita, U.S.Paulsen, T.F.Pedersen Risø-DTU Technical University of Denmark, Roskilde, Denmark luca.vita@risoe.dk Abstract: A novel concept
More informationControl Strategies for operation of pitch regulated turbines above cut-out wind speeds
Control Strategies for operation of pitch regulated turbines above cut-out wind speeds Helen Markou 1 Denmark and Torben J. Larsen, Risø-DTU, P.O.box 49, DK-4000 Roskilde, Abstract The importance of continuing
More informationEXPERIMENTAL INVESTIGATIONS OF BARGE FLOATER WITH MOONPOOL FOR 5 MW WIND TURBINE
EXPERIMENTAL INVESTIGATIONS OF BARGE FLOATER WITH MOONPOOL FOR 5 MW WIND TURBINE 1 MR. G.VIJAYA KUMAR, 2 DR. R. PANNEER SELVAM 1 M.S. Research Scholar, Department of Ocean Engineering, IIT Madras, Chennai,
More informationDynamic analysis of offshore floating wind turbines
Dynamic analysis of offshore floating wind turbines Hasan Bagbanci Centre for Marine Technology and Engineering (CENTEC), Instituto Superior Técnico Technical University of Lisbon, Lisboa, Portugal ABSTRACT:
More informationA comprehensive method for the structural design and verification of the INNWIND 10MW tri-spar floater
NATIONAL TECHNICAL UNIVERSITY of ATHENS (NTUA) A comprehensive method for the structural design and verification of the INNWIND 10MW tri-spar floater DI Manolas, CG Karvelas, IA Kapogiannis, VA Riziotis,
More informationTension-Leg-Buoy (TLB) Platforms for Offshore Wind Turbines
Tension-Leg-Buoy (TLB) Platforms for Offshore Wind Turbines EERA DeepWind'2014 Deep Sea Offshore Wind R&D Conference, Trondheim, 22-24 January 2014 Tor Anders Nygaard, Institute for Energy Technology (IFE),
More informationAmeliorating the Negative Damping in the Dynamic Responses of a Tension Leg Spar-Type Support Structure with a Downwind Turbine
1 Ameliorating the Negative Damping in the Dynamic Responses of a Tension Leg Spar-Type Support Structure with a Downwind Turbine Madjid Karimirad Torgeir Moan Author CeSOS Centre Centre for Ships for
More informationINSIGHT INTO THE UNSTEADY AERODYNAMICS OF FLOATING WIND TURBINES WITH TENSION LEG PLATFORMS (TLP) USING A BLADE ELEMENT MOMENTUM (BEM) BASED MODEL
HEFAT212 9 th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics 16 18 July 212 Malta INSIGHT INTO THE UNSTEADY AERODYNAMICS OF FLOATING WIND TURBINES WITH TENSION LEG PLATFORMS
More informationModel Tests for a Floating Wind Turbine on Three Different Floaters
Bonjun J. Koo 1 Technip USA, Inc., 11700 Katy Freeway, Suite 150, Houston, TX 77079 e-mail: bkoo@technip.com Andrew J. Goupee Advanced Structures and Composites Center, University of Maine, 35 Flagstaff
More informationEFFECT OF DIFFERENT MOORING SYSTEMS ON HYDRODYNAMIC ANALYSIS OF AN OFFSHORE WIND TURBINE
EFFECT OF DIFFERENT MOORING SYSTEMS ON HYDRODYNAMIC ANALYSIS OF AN OFFSHORE WIND TURBINE Sabri ALKAN 1, Ayhan Mentes 2, Ismail H. Helvacioglu 2, Nagihan Turkoglu 2 1 Department of Mechanical Engineering,
More informationProceedings of the ASME nd International Conference on Ocean, Offshore and Arctic Engineering OMAE2013 June 9-14, 2013, Nantes, France
Proceedings of the ASME 2013 32nd International Conference on Ocean, Offshore and Arctic Engineering OMAE2013 June 9-14, 2013, Nantes, France OMAE2013-10463 MOTION OF OC4 5MW SEMI-SUBMERSIBLE OFFSHORE
More information2MW baseline wind turbine: model development and verification (WP1) The University of Tokyo & Hitachi, Ltd.
2MW baseline wind turbine: model development and verification (WP1) The University of Tokyo & Hitachi, Ltd. Downwind turbine technology, IEA Wind Task 40 First Progress Meeting, Tokyo, Japan 11 Dec, 2017
More informationResponse Analysis of a Spar-Type Floating Offshore Wind Turbine Under Atmospheric Icing Conditions
Journal of Ocean and Wind Energy (ISSN 2310-3604) Copyright by The International Society of Offshore and Polar Engineers Vol. 1, No. 4, November 2014, pp. 193 201 http://www.isope.org/publications Response
More informationLoad Consequences when Sweeping Blades - A Case Study of a 5 MW Pitch Controlled Wind Turbine
Downloaded from orbit.dtu.dk on: Nov 26, 2018 Load Consequences when Sweeping Blades - A Case Study of a 5 MW Pitch Controlled Wind Turbine Verelst, David Robert; Larsen, Torben J. Publication date: 2010
More informationThe 5 MW Deepwind Floating Offshore Vertical Wind Turbine Concept Design - Status And Perspective. Uwe Schmidt Paulsen
The 5 MW Deepwind Floating Offshore Vertical Wind Turbine Concept Design - Status And Perspective Uwe Schmidt Paulsen uwpa@dtu.dk Contents What is DeepWind Motivation and Background Concept Design Status
More informationEXPERIMENTAL COMPARISON OF THREE FLOATING WIND TURBINE CONCEPTS
Proceedings of the 31 st International Conference on Ocean, Offshore and Arctic Engineering OMAE2012 Rio de Janeiro, Brazil June 10-15, 2012 OMAE2012-83645 EXPERIMENTAL COMPARISON OF THREE FLOATING WIND
More informationCatenary Mooring Chain Eigen Modes and the Effects on Fatigue Life
Catenary Mooring Chain Eigen Modes and the Effects on Fatigue Life Tor Anders Nygaard and Jacobus de Vaal, IFE Morten Hviid Madsen and Håkon Andersen, Dr.techn Olav Olsen AS Jorge Altuzarra, Vicinay Marine
More informationAero-Hydro-Servo-Elastic Analysis of Floating Wind. Leg Moorings. January ar 7, 2013
1 Aero-Hydro-Servo-Elastic Analysis of Floating Wind Turbines with Tension Leg Moorings Erin Bachynski, PhD candidate at CeSOS erin.bachynski@ntnu.no January ar 7, 2013 Erin Bachynski CeSOS Centre for
More informationSteady State Comparisons HAWC2 v12.5 vs HAWCStab2 v2.14: Integrated and distributed aerodynamic performance
Downloaded from orbit.dtu.dk on: Jan 29, 219 Steady State Comparisons v12.5 vs v2.14: Integrated and distributed aerodynamic performance Verelst, David Robert; Hansen, Morten Hartvig; Pirrung, Georg Publication
More informationHywind. Deep offshore wind operational experience. Finn Gunnar Nielsen, Statoil RDI
Hywind. Deep offshore wind operational experience. Finn Gunnar Nielsen, Statoil RDI The starting point -2001 Inspired by floating sailing marks. Seawind matured during 2002 Tong, K.C. OWEMES seminar, Atena,
More informationImpact on wind turbine loads from different down regulation control strategies
Downloaded from orbit.dtu.dk on: Jan 24, 2019 Impact on wind turbine loads from different down regulation control strategies Galinos, Christos; Larsen, Torben J.; Mirzaei, Mahmood Published in: Journal
More informationPerformance Calculation of Floating Wind Turbine Tension Leg Platform in the South China Sea
568 J. Eng. Technol. Sci., Vol. 47, No. 5, 2015, 568-588 Performance Calculation of Floating Wind Turbine Tension Leg Platform in the South China Sea Hai Feng Wang & You Hua Fan School of Natural Sciences
More informationADDITIONAL WIND/WAVE BASIN TESTING OF THE DEEPCWIND SEMI- SUBMERSIBLE WITH A PERFORMANCE-MATCHED WIND TURBINE
Proceedings of the ASME 214 33rd International Conference on Ocean, Offshore and Arctic Engineering OMAE214 June 8-13, 214, San Francisco, California, USA OMAE214-24172 ADDITIONAL WIND/WAVE BASIN TESTING
More informationEvaluation of wind loads by a passive yaw control at the extreme wind speed condition and its verification by measurements
Evaluation of wind loads by a passive yaw control at the extreme wind speed condition and its verification by measurements Dec/11/2017 Soichiro Kiyoki Takeshi Ishihara Mitsuru Saeki Ikuo Tobinaga (Hitachi,
More informationAvailable online at ScienceDirect. Energy Procedia 80 (2015 )
Available online at www.sciencedirect.com ScienceDirect Energy Procedia ( ) 6 th Deep Sea Offshore Wind R&D Conference, EERA DeepWind' Coupled mooring systems for floating wind farms Marek Goldschmidt*,
More informationINFLUENCE OF AERODYNAMIC MODEL FIDELITY ON ROTOR LOADS DURING FLOATING OFFSHORE WIND TURBINE MOTIONS
INFLUENCE OF AERODYNAMIC MODEL FIDELITY ON ROTOR LOADS DURING FLOATING OFFSHORE WIND TURBINE MOTIONS DENIS MATHA 1,2*, LEVIN KLEIN 3, DIMITRIOS BEKIROPOULOS 3, PO WEN CHENG 2 1 RAMBOLL WIND, GERMANY *
More informationCOUPLED AND UNCOUPLED ANALYSIS OF Y-WIND SEMI WIND TURBINE FOUNDATION
COUPLED AND UNCOUPLED ANALYSIS OF Y-WIND SEMI WIND TURBINE FOUNDATION HYOUNGCHUL KIM VL OFFSHORE (GRADUATE INTERN) SUNG YOUN BOO VL OFFSHORE (VICE PRESIDENT) Proceedings of the 23 rd Offshore Symposium,
More informationExperimental Comparison of Three Floating Wind Turbine Concepts
Andrew J. Goupee 1 Advanced Structures and Composites Center, University of Maine, 35 Flagstaff Road, Orono, ME 04469 e-mail: agoupe91@maine.edu Bonjun J. Koo Technip USA, Inc., 11700 Katy Freeway, Suite
More informationVertical Axis Wind Turbine Design Load Cases Investigation and Comparison with Horizontal Axis Wind Turbine
Downloaded from orbit.dtu.dk on: May 13, 2018 Vertical Axis Wind Turbine Design Load Cases Investigation and Comparison with Horizontal Axis Wind Turbine Galinos, Christos; Larsen, Torben J.; Aagaard Madsen,
More informationDual pitch revisited: Overspeed avoidance by independent control of two blade sections
Dual pitch revisited: Overspeed avoidance by independent control of two blade sections P. Brosche, B. Fischer, P. Loepelmann, M. Shan {philipp.brosche, boris.fischer, peter.loepelmann, martin.shan}@iwes.fraunhofer.de
More informationThe Benefits Of Composite Materials In Deepwater Riser Applications. 26 th March 2015 Hassan Saleh Senior Engineer 2H Offshore Engineering Ltd
The Benefits Of Composite Materials In Deepwater Riser Applications 26 th March 2015 Hassan Saleh Senior Engineer 2H Offshore Engineering Ltd Composite Benefits and Challenges Composite Materials offer
More informationSuperGen UK Centre for Marine Energy Research Progress Meeting 2018
SuperGen UK Centre for Marine Energy Research Progress Meeting 2018 Extreme loads and survivability Cameron Johnstone, Stephanie Ordonez-Sanchez, Song Fu and Rodrigo Martinez Energy Systems Research Unit,
More informationCoupled Dynamic Modeling of Floating Wind Turbine Systems
National Renewable Energy Laboratory Innovation for Our Energy Future A national laboratory of the U.S. Department of Energy Office of Energy Efficiency & Renewable Energy Coupled Dynamic Modeling of Floating
More informationModelling of Wind Turbine Loads nearby a Wind Farm
Journal of Physics: Conference Series PAPER OPEN ACCESS Modelling of Wind Turbine Loads nearby a Wind Farm To cite this article: B Roscher et al 2017 J. Phys.: Conf. Ser. 854 012038 View the article online
More informationEffect of Turbulence on Power for Bend-Twist Coupled Blades
Journal of Physics: Conference Series PAPER OPEN ACCESS Effect of Turbulence on Power for Bend-Twist Coupled Blades To cite this article: Alexander R. Stäblein and Morten H. Hansen 1 J. Phys.: Conf. Ser.
More informationComparison of coupled aero-hydro-servo-elastic simulations for floating wind turbines with model tests
Comparison of coupled aero-hydro-servo-elastic for floating wind turbines with Georgios Chrysagis Delft University of Technology, The Netherlands Email: georgechrysagis@hotmail.com September 2016 Key words:
More informationRELATIVE CONTRIBUTION FROM WIND AND WAVES TO LOADS ON OFFSHORE WIND TURBINES
RELATIVE CONTRIBUTION FROM WIND AND WAVES TO LOADS ON OFFSHORE WIND TURBINES Science Meets Industry Stavanger By Jørgen R. Krokstad WITH FOCUS ON SUPPORT STRUCTURES (with contributions from Loup Suja Thauvin
More informationM.Sc.THESIS. Dynamic Response Analysis of an Offshore Wind Turbine. Delivered: June 14th, Title: Availability: Open.
NTNU Norwegian University of Science and Technology Department of Marine Technology M.Sc.THESIS Title: Student: Dynamic Response Analysis of an Offshore Wind Turbine Yu Li Delivered: June 14th, 2011 Availability:
More informationCoupled Aero-hydrodynamic Analysis on a Floating Offshore Wind Turbine under Extreme Sea Conditions
Proceedings of the Twenty-seventh (2017) International Ocean and Polar Engineering Conference San Francisco, CA, USA, June 25-30, 2017 Copyright 2017 by the International Society of Offshore and Polar
More informationFloating Wind Turbines
FINAL REPORT Floating Wind Turbines May 212 Prepared by American Bureau of Shipping Corporate Offshore Technology, Renewables 16855 Northchase Drive Houston, Texas 776 www.eagle.org Submitted to U.S. Department
More informationAnalyses of the mechanisms of amplitude modulation of aero-acoustic wind turbine sound
Analyses of the mechanisms of amplitude modulation of aero-acoustic wind turbine sound Andreas Fischer Helge Aagaard Madsen Knud Abildgaard Kragh Franck Bertagnolio DTU Wind Energy Technical University
More informationEffect of wind flow direction on the loads at wind farm. Romans Kazacoks Lindsey Amos Prof William Leithead
Effect of wind flow direction on the loads at wind farm Romans Kazacoks Lindsey Amos Prof William Leithead Objectives: Investigate the effect of wind flow direction on the wind turbine loads (fatigue)
More informationCOUPLED DYNAMIC ANALYSIS OF MOORING LINES FOR DEEP WATER FLOATING SYSTEMS
Proceedings of International Conference in Ocean Engineering, ICOE Proceedings 2009 of ICOE 2009 Coupled Dynamic Analysis IIT Madras, of Chennai, Mooring India. Lines for Deep Water Floating Systems 1-5
More informationDevelopment of Self-Installing Deepwater Spar. Ashit Jadav February 2017
Development of Self-Installing Deepwater Spar Ashit Jadav February 2017 Contents Introduction & Background ACE Spar breakdown Installation Sequence Main particulars, Hull design and Weight control Stability
More informationAvailable online at ScienceDirect. Energy Procedia 53 (2014 ) 2 12
Available online at www.sciencedirect.com ScienceDirect Energy Procedia 53 (24 ) 2 2 EERA DeepWind 24, th Deep Sea Offshore Wind R&D Conference Concept design verification of a semi-submersible floating
More informationCopyright by Mohit Soni 2014
Copyright by Mohit Soni 4 The Thesis Committee for Mohit Soni Certifies that this is the approved version of the following thesis: Dynamic Response Analysis of an Offshore Wind Turbine Supported by a Moored
More informationEXPERIMENTAL STUDY ON THE HYDRODYNAMIC BEHAVIORS OF TWO CONCENTRIC CYLINDERS
EXPERIMENTAL STUDY ON THE HYDRODYNAMIC BEHAVIORS OF TWO CONCENTRIC CYLINDERS *Jeong-Rok Kim 1), Hyeok-Jun Koh ), Won-Sun Ruy 3) and Il-Hyoung Cho ) 1), 3), ) Department of Ocean System Engineering, Jeju
More informationDeepwater Floating Production Systems An Overview
Deepwater Floating Production Systems An Overview Introduction In addition to the mono hull, three floating structure designs Tension leg Platform (TLP), Semisubmersible (Semi), and Truss Spar have been
More informationBasic Design and Finite Element Analysis of Substructure of 2.5MW. Floating-type Offshore Wind Turbine. O-Kaung Lim 3)
The 2012 World Congress on Advances in Civil, Environmental, and Materials Research (ACEM 12) Seoul, Korea, August 26-30, 2012 Basic Design and Finite Element Analysis of Substructure of 2.5MW Floating-type
More informationThomas Lykke Andersen, Morten Kramer, Peter Frigaard November 2003
Thomas Lykke Andersen, Morten Kramer, Peter Frigaard November 2003 HYDRAULICS & COASTAL ENGINEERING LABORATORY AALBORG UNIVERSITY DEPARTMENT OF CIVIL ENGINEERING SOHNGAARDSHOLMSVEJ 57 DK-9000 AALBORG DENMARK
More informationCopyright by Jinsong Liu 2015
Copyright by Jinsong Liu 2015 The Thesis Committee for Jinsong Liu certifies that this is the approved version of the following thesis: On the Development of a Semi-Submersible Offshore Floating Platform
More informationPRESSURE DISTRIBUTION OF SMALL WIND TURBINE BLADE WITH WINGLETS ON ROTATING CONDITION USING WIND TUNNEL
International Journal of Mechanical and Production Engineering Research and Development (IJMPERD ) ISSN 2249-6890 Vol.2, Issue 2 June 2012 1-10 TJPRC Pvt. Ltd., PRESSURE DISTRIBUTION OF SMALL WIND TURBINE
More informationRELIABILITY ASSESSMENT, STATIC AND DYNAMIC RESPONSE OF TRANSMISSION LINE TOWER: A COMPARATIVE STUDY
RELIABILITY ASSESSMENT, STATIC AND DYNAMIC RESPONSE OF TRANSMISSION LINE TOWER: A COMPARATIVE STUDY Yusuf Mansur Hashim M. Tech (Structural Engineering) Student, Sharda University, Greater Noida, (India)
More informationOffshore Oil and Gas Platforms for Deep Waters
Offshore Oil and Gas Platforms for Deep Waters Atilla Incecik Department of Naval Architecture, Ocean and Marine Engineering University of Strathclyde, Glasgow, UK (atilla.incecik@strath.ac.uk) Summary
More informationInternational Journal of Scientific & Engineering Research, Volume 7, Issue 10, October ISSN
International Journal of Scientific & Engineering Research, Volume 7, Issue 10, October-2016 172 DYNAMIC ANALYSIS OF MINI TENSION LEG PLATFORMS UNDER RANDOM WAVES Shibin P Shaji, Dr. Jayalekshmi R. Abstract
More informationModal Analysis of Barrels for Assault Rifles
PROBLEMS OF MECHATRONICS ARMAMENT, AVIATION, SAFETY ENGINEERING ISSN 2081-5891 2 (8), 2012, 7-16 Modal Analysis of Barrels for Assault Rifles Peter LISÝ, Mário ŠTIAVNICKÝ Academy of the Armed Forces of
More informationITTC Recommended Procedures and Guidelines
Page 1 of 6 Table of Contents 1. PURPOSE...2 2. PARAMETERS...2 2.1 General Considerations...2 3 DESCRIPTION OF PROCEDURE...2 3.1 Model Design and Construction...2 3.2 Measurements...3 3.5 Execution of
More informationPressure distribution of rotating small wind turbine blades with winglet using wind tunnel
Journal of Scientific SARAVANAN & Industrial et al: Research PRESSURE DISTRIBUTION OF SMALL WIND TURBINE BLADES WITH WINGLET Vol. 71, June 01, pp. 45-49 45 Pressure distribution of rotating small wind
More informationThe EllipSys2D/3D code and its application within wind turbine aerodynamics
The EllipSys2D/3D code and its application within wind turbine aerodynamics Niels N. Sørensen Wind Energy Department, Risø DTU National Laboratory for Sustainable Energy and Dep. Civil Engineering, Aalborg
More informationCOMPUTER-AIDED DESIGN AND PERFORMANCE ANALYSIS OF HAWT BLADES
5 th International Advanced Technologies Symposium (IATS 09), May 13-15, 2009, Karabuk, Turkey COMPUTER-AIDED DESIGN AND PERFORMANCE ANALYSIS OF HAWT BLADES Emrah KULUNK a, * and Nadir YILMAZ b a, * New
More informationIntegrated System Design for a Large Wind Turbine Supported on a Moored Semi-Submersible Platform
Journal of Marine Science and Engineering Article Integrated System Design for a Large Wind Turbine Supported on a Moored Semi-Submersible Platform Jinsong Liu, Edwin Thomas, Lance Manuel, * ID, D. Todd
More informationCoupling and Analysis of 981 Deep Water Semi-submersible. Drilling Platform and the Mooring System
4th International Conference on Renewable Energy and Environmental Technology (ICREET 2016) Coupling and Analysis of 981 Deep Water Semi-submersible Drilling Platform and the Mooring System XuDong Wang1,
More informationParametric Investigation of Dynamic Characteristics of Mooring Cable of Floating-type Offshore Wind Turbine
The 0 World Congress on Advances in Civil, Environmental, and Materials Research (ACEM ) Seoul, Korea, August 6-30, 0 Parametric Investigation of Dynamic Characteristics of Mooring Cable of Floating-type
More informationINCLINOMETER DEVICE FOR SHIP STABILITY EVALUATION
Proceedings of COBEM 2009 Copyright 2009 by ABCM 20th International Congress of Mechanical Engineering November 15-20, 2009, Gramado, RS, Brazil INCLINOMETER DEVICE FOR SHIP STABILITY EVALUATION Helena
More informationWIND-INDUCED LOADS OVER DOUBLE CANTILEVER BRIDGES UNDER CONSTRUCTION
WIND-INDUCED LOADS OVER DOUBLE CANTILEVER BRIDGES UNDER CONSTRUCTION S. Pindado, J. Meseguer, J. M. Perales, A. Sanz-Andres and A. Martinez Key words: Wind loads, bridge construction, yawing moment. Abstract.
More informationOFFSHORE WIND: A CRASH COURSE
OFFSHORE WIND: A CRASH COURSE OFFSHORE WIND: DEFINED OFFSHORE WIND: Construction of wind farms in bodies of water to generate electricity from wind. Unlike the typical usage of the term offshore in the
More informationE02 Rigid hinged stinger with piggyback line
E02 Rigid hinged stinger with piggyback line This model represents a rigid stinger hinged off the back of a lay vessel using the pipelay supports feature. In addition to the lay pipe, another line is included
More informationAerodynamic Thrust Modelling in Wave Tank Tests of Offshore Floating Wind Turbines Using a Ducted Fan
Journal of Physics: Conference Series OPEN ACCESS Aerodynamic Thrust Modelling in Wave Tank Tests of Offshore Floating Wind Turbines Using a Ducted Fan To cite this article: José Azcona et al 2014 J. Phys.:
More informationLearn more at
Full scale model tests of a steel catenary riser C. Bridge 1, H. Howells 1, N. Toy 2, G. Parke 2, R. Woods 2 1 2H Offshore Engineering Ltd, Woking, Surrey, UK 2 School of Engineering, University of Surrey,
More informationThe Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration. M. Burak Şamşul
The Usage of Propeller Tunnels For Higher Efficiency and Lower Vibration M. Burak Şamşul ITU AYOC 2014 - Milper Pervane Teknolojileri Company Profile MILPER is established in 2011 as a Research and Development
More informationAssessment of 3D aerodynamic effects on the behaviour of floating wind turbines
Journal of Physics: Conference Series OPEN ACCESS Assessment of 3D aerodynamic effects on the behaviour of floating wind turbines To cite this article: D Manolas et al 2014 J. Phys.: Conf. Ser. 555 012067
More informationInnovative and Robust Design. With Full Extension of Offshore Engineering and Design Experiences.
Innovative and Robust Design by VL Offshore With Full Extension of Offshore Engineering and Design Experiences www.vloffshore.com Y Wind Semi Designed by VL Offshore The Y Wind Semi platform (foundation)
More informationExtended Onshore Control of a Floating Wind Turbine with Wave Disturbance Reduction
Journal of Physics: Conference Series OPEN ACCESS Extended Onshore Control of a Floating Wind Turbine with Wave Disturbance Reduction To cite this article: S Christiansen et al 214 J. Phys.: Conf. Ser.
More informationMASTER THESIS PRESENTATION. Comparison Of Seakeeping Performance Of The Two Super Yachts Of 53 And 46 m In Length
MASTER THESIS PRESENTATION Comparison Of Seakeeping Performance Of The Two Super Yachts Of 53 And 46 m In Length Muhammad Asim Saleem Supervisor : Prof. Dario Boote, Universita degli studi di Genova, Italy
More informationDynamic Positioning Control Augmentation for Jack-up Vessels
DYNAMIC POSITIONING CONFERENCE October 9-10, 2012 Design and Control Session Dynamic Positioning Control Augmentation for Jack-up Vessels By Bradley Deghuee L-3 Communications 1 Introduction Specialized
More informationHydrodynamic Analysis of a Heavy Lift Vessel during Offshore Installation Operations
Presentation for Defense of Master Thesis Hydrodynamic Analysis of a Heavy Lift Vessel during Offshore Installation Operations Speaker: Bin Wang Supervisor: Prof. Robert Bronsart 23 rd Feb, 2015 Nantes
More informationTLP Minimum tendon tension design and tendon down-stroke investigation
Published by International Association of Ocean Engineers Journal of Offshore Engineering and Technology Available online at www.iaoejoet.org TLP Minimum tendon tension design and tendon down-stroke investigation
More informationExperimental Results for Tension-Leg-Buoy Offshore Wind Turbine Platforms
Journal of Ocean and Wind Energy (ISSN 2310-3604) Copyright by The International Society of Offshore and Polar Engineers Vol. 1, No. 4, November 2014, pp. 217 224 http://www.isope.org/publications Experimental
More informationOperations. On The Use of Safety Moorings in DP Operations
Return to Session Directory DYNAMIC POSITIONING CONFERENCE October 7-8, 28 Operations On The Use of Safety Moorings in DP Operations Nils Albert Jenssen Kongsberg Maritime, (Kongsberg Norway) Abstract
More informationProceedings of Meetings on Acoustics
Proceedings of Meetings on Acoustics Volume 9, 2010 http://acousticalsociety.org/ 159th Meeting Acoustical Society of America/NOISE-CON 2010 Baltimore, Maryland 19-23 April 2010 Session 1pBB: Biomedical
More informationLight Rotor: The 10-MW reference wind turbine
Downloaded from orbit.dtu.dk on: Apr 23, 2018 Light Rotor: The 10-MW reference wind turbine Bak, Christian; Bitsche, Robert; Yde, Anders; Kim, Taeseong; Hansen, Morten Hartvig; Zahle, Frederik; Gaunaa,
More informationVINDKRAFTNET MEETING ON TURBULENCE
VINDKRAFTNET MEETING ON TURBULENCE On-going Work on Wake Turbulence in DONG Energy 28/05/2015 Cameron Brown Load Engineer Lucas Marion R&D graduate Who are we? Cameron Brown Load Engineer from Loads Aerodynamics
More informationStudy on wind turbine arrangement for offshore wind farms
Downloaded from orbit.dtu.dk on: Jul 01, 2018 Study on wind turbine arrangement for offshore wind farms Shen, Wen Zhong; Mikkelsen, Robert Flemming Published in: ICOWEOE-2011 Publication date: 2011 Document
More informationIMO REVISION OF THE INTACT STABILITY CODE. Proposal of methodology of direct assessment for stability under dead ship condition. Submitted by Japan
INTERNATIONAL MARITIME ORGANIZATION E IMO SUB-COMMITTEE ON STABILITY AND LOAD LINES AND ON FISHING VESSELS SAFETY 49th session Agenda item 5 SLF 49/5/5 19 May 2006 Original: ENGLISH REVISION OF THE INTACT
More informationRef. Ares(2018) /01/2018
Ref. Ares(2018)319491-18/01/2018 Deliverable 3.3 Feasibility assessment of Symphony stuctural membrane as a negative spring and replacement for mechanical components in other heaving WECs DATE: November
More informationExperimental Determination of Temperature and Pressure Profile of Oil Film of Elliptical Journal Bearing
International Journal of Advanced Mechanical Engineering. ISSN 2250-3234 Volume 4, Number 5 (2014), pp. 469-474 Research India Publications http://www.ripublication.com Experimental Determination of Temperature
More informationGEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS
SMART SOLUTIONS FOR VIBRATION MONITORING GEA FOR ADVANCED STRUCTURAL DYNAMIC ANALYSIS ANALYSIS OF CIVIL STRUCTURES - EXPO MERLATA PEDESTRIAN BRIDGE ABSTRACT Civil structures and in particular bridges and
More informationAN ISOLATED SMALL WIND TURBINE EMULATOR
AN ISOLATED SMALL WIND TURBINE EMULATOR Md. Arifujjaman Graduate Student Seminar: Master of Engineering Faculty of Engineering and Applied Science Memorial University of Newfoundland St. John s, NL, Canada
More informationLoad validation and comparison versus certification approaches of the Risø Dynamic Wake Meandering model implementation in GH Bladed
Load validation and comparison versus certification approaches of the Risø Dynamic Wake Meandering model implementation in GH Bladed Björn Schmidt John King Gunner C. Larsen Torben J. Larsen Germanischer
More informationOMAE A COMPARISON OF TWO COUPLED MODEL OF DYNAMICS FOR OFFSHORE FLOATING VERTICAL AXIS WIND TURBINES (VAWT)
Proceedings of the ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineeing OMAE2014 June 8-13, 2014, San Francisco, California, USA OMAE2014-23301 A COMPARISON OF TWO COUPLED MODEL
More informationProceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14) 30-31,December, 2014, Ernakulam, India
INTERNATIONAL JOURNAL OF DESIGN AND MANUFACTURING TECHNOLOGY (IJDMT) Proceedings of the International Conference on Emerging Trends in Engineering and Management (ICETEM14) ISSN 0976 6995 (Print) ISSN
More informationCRITERIA OF BOW-DIVING PHENOMENA FOR PLANING CRAFT
531 CRITERIA OF BOW-DIVING PHENOMENA FOR PLANING CRAFT Toru KATAYAMA, Graduate School of Engineering, Osaka Prefecture University (Japan) Kentarou TAMURA, Universal Shipbuilding Corporation (Japan) Yoshiho
More informationExecutive Summary of Accuracy for WINDCUBE 200S
Executive Summary of Accuracy for WINDCUBE 200S The potential of offshore wind energy has gained significant interest due to consistent and strong winds, resulting in very high capacity factors compared
More informationDesign and manufacturing basalt and carbon fiber road bike frame.
MATERIALES COMPUESTOS 15 1 Design and manufacturing basalt and carbon road bike frame. E. Romero, RACORMANCE Composites Bikes. J. Justo, F. París Group of Elasticity and Strength of Materials, University
More informationComparison of Phatas versions and the Wind Turbine module C. Lindenburg
ECN-E--11-66 Comparison of Phatas versions and the Wind Turbine module C. Lindenburg December 211 Preface The program Phatas is developed at ECN wind energy for the design and analysis of horizontal axis
More informationTHE HORNS REV WIND FARM AND THE OPERATIONAL EXPERIENCE WITH THE WIND FARM MAIN CONTROLLER
Copenhagen Offshore Wind 25, 26-28 October 25 1 THE HORNS REV WIND FARM AND THE OPERATIONAL EXPERIENCE WITH THE WIND FARM MAIN CONTROLLER Jesper Runge Kristoffersen M.Sc.EE Elsam Engineering A/S, Kraftværksvej
More informationStructural Dynamic Analysis of Semi-Submersible Floating Vertical Axis Wind Turbines
energies Article Structural Dynamic Analysis of Semi-Submersible Floating Vertical Axis Wind Turbines Jeremiah Ishie 1, Kai Wang 2, * Muk Chen Ong 1 1 Department of Mechanical Structural Engineering Material
More informationTime Domain Flutter Analysis of Bend-Twist Coupled Composite Wind Turbine Blades and Comparisons with the Baseline Blade
Time Domain Flutter Analysis of Bend-Twist Coupled Composite Wind Turbine Blades and Comparisons with the Baseline Blade *Touraj Farsadi 1) and Altan Kayran 2) 1), 2) METUWind centre, Department of Aerospace
More informationU S F O S B u o y a n c y And Hydrodynamic M a s s
1 U S F O S B u o y a n c y And Hydrodynamic M a s s 2 CONTENTS: 1 INTRODUCTION... 3 2 ACCURACY LEVELS... 3 2.1 LEVEL-0... 3 2.2 LEVEL-1... 3 2.3 PANEL MODEL... 3 3 EX 1. SINGLE PIPE. NON FLOODED... 4
More information