Binks Model 21 (Brass Body) Automatic Spray Gun General Arrangement Diagram and Hook-Up. Side Port Control. Fluid. Cylinder Air Fluid.
|
|
- Ethan Black
- 6 years ago
- Views:
Transcription
1 Binks Model 21 Automatic Spray Gun (Brass Body) 6220-XXXX-X Binks Model 21 (Brass Body) Automatic Spray Gun General Arrangement Diagram and Hook-Up Atomizing Air Cylinder Air Shut-Off Cocks To Supply Atomizing Air (Through Extractor) 3-Way Valve Cylinder Air (Through Extractor) For multiple gun installation, a fluid manifold may be used. adjustments are made using the fluid control screw on each gun. However, when precise fluid control is necessary, a fluid regulator for each gun must be used. Side Port Control Mounting Hole (1/2" Dia.) Inlet 3/8 NPS(m) Atomizing Air Inlet 1/4 NPS(m) Mounting Lockscrew Adjustment Control Cylinder Operating Air Inlet 1/4 NPS(m), (50-60 PSI Min.) Oil and Water Extractor Air Supply from Compressor or Air Line Typical Air Compressor Oil and Water Extractor Atomizing Air Air Supply to Pressure Tank Inlet Typical Pressure Tank Cylinder Air 3-Way Valve Air Supply from Compressor or Air Line Pump Speed Control Typical Pump w/ Container Atomizing Air Back Pressure Control 3-Way Valve Cylinder Air 1. Provide PSI (minimum) air pressure for gun cylinder operation. 2. Air line from gun to 3-way valve should be as short as possible for maximum speed of operation. 3. Recommended hose sizes are 3/8" for fluid and 1/4" for air. Replaces Part Sheet R-17 Part Sheet R-18
2 In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows:!! CAUTION NOTE WARNING Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product or property damage.! WARNING Read the following warnings before using this equipment. Important installation, operation or maintenance information. READ THE MANUAL Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation manual. INSPECT THE EQUIPMENT DAILY Inspect the equipment for worn or broken parts on a daily basis. Do not operate the equipment if you are uncertain about its condition. WEAR SAFETY GLASSES Failure to wear safety glasses with side shields could result in serious eye injury or blindness. NEVER MODIFY THE EQUIPMENT Do not modify the equipment unless the manufacturer provides written approval. DE-ENERGIZE, DISCONNECT AND LOCK OUT ALL POWER SOURCES DURING MAINTENANCE Failure to De-energize, disconnect and lock out all power supplies before performing equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT IN CASE OF AN EMERGENCY OPERATOR TRAINING All personnel must be trained before operating finishing equipment. PRESSURE RELIEF PROCEDURE Always follow the pressure relief procedure in the equipment instruction manual. EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equip ment to rupture, malfunction, or start unexpectedly and result in serious injury. NOISE HAZARD You may be injured by loud noise. Hearing protection may be required when using this equipment. KEEP EQUIPMENT GUARDS IN PLACE Do not operate the equipment if the safety devices have been removed. PROJECTILE HAZARD You may be injured by venting liquids or gases that are released under pressure, or flying debris. PINCH POINT HAZARD Moving parts can crush and cut. Pinch points are basically any areas where there are moving parts. STATIC CHARGE may develop a static charge that must be dissipated through proper grounding of the equipment, objects to be sprayed and all other electrically conductive objects in the dispensing area. Improper grounding or sparks can cause a hazardous condition and result in fire, explosion or electric shock and other serious injury. FIRE AND EXPLOSION HAZARD Never use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in equipment with aluminum wetted parts. Such use could result in a serious chemical reaction, with the possibility of explosion. Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum parts. AUTOMATIC EQUIPMENT Automatic equipment may start suddenly without warning. CA PROP 65 PROP 65 WARNING WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PROVIDE THIS INFORMATION TO THE OPERATOR OF THE EQUIPMENT. 2 FOR FURTHER SAFETY INFORMATION REGARDING BINKS AND DEVILBISS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET ( ).
3 Binks Model 21 (BRASS BODY) Automatic Spray Gun Hook-Up 1. Air pressure of PSI minimum required for cylinder operation. 2. For rapid operation, the air line between three-way valve and the cylinder operating air connection should be as short as possible. 3. All air supplied to the gun should be dirt and moisturefree. An oil and water extractor mounted in the air supply line is recommended. 4. If the gun is to stand idle for any length of time, shut off. This will prevent small leaks throughout the system from turning on the gun. Fan Spray Adjustments The fan spray is easily controlled by means of the side port control stem, (22). Turning this control to the right, or clockwise, will give a round spray pattern. Turning it to the left, or counter-clockwise, will widen the spray into a fan shape of any desired width. Orientation of the fan spray either horizontally or vertically (or to any position in between) is obtained by loosening the retainer ring, rotating the air nozzle to the desired position, and then tightening the retainer ring. FLUID FLOW adjustments For best results, the fluid control screw (18) should be set at the open position and the flow of the fluid controlled by regulating the fluid pressure in the pressure tank. If the conditions under which the gun is being used require the fluid to be controlled at the gun, it may be accomplished by loosening locknut (19) and turning screw (18) to the right (clockwise) to decrease the flow of fluid or the left (counter-clockwise) to increase the flow of fluid. Lubrication The points that require lubrication on this gun are the plunger (7), the air valve packing (11), and the fluid packing (36). These parts should be kept soft and pliable at all times. A light machine oil is recommended for this lubrication.! Caution Never submerge the gun in solvent. Solvent will wash the oil off the lubricated parts and cause subsequent malfunctioning of the gun. Cleaning Shut off the air supply to the tank and release its pressure. Hold a piece of wadded cloth over the gun nozzle and turn on the air to the cylinder. The air will back up through the fluid nozzle and force fluid out of the hose and into the tank. Replace the paint in the pressure tank with clean solvent and spray the solvent through the gun until it is clean. Dry out the residual solvent in the fluid hose by blowing air through it. Faulty Spray Faulty spray is caused by dry coating material residue around the fluid nozzle tip or inside the air nozzle. Soak these parts in a solvent that will soften the dried residue until it can be removed with a brush or a cloth.! Caution Never use metal probes to clean the air or fluid nozzles because scratches and burns on their precision machined surfaces can cause faulty spray. If either the air or fluid nozzle is damaged so as to give faulty spray, it must be replaced. INTERNAL MIX HEAVY MATERIAL NOZZLES (OPTIONAL) FLUID NOZZLE* 59ASS, 59BSS, 59CSS AIR NOZZLE* 240 THRU 262 NITRALLOY AIR NOZZLE* 706, 709SS, NEEDLE ASSEMBLY AIR NOZZLE ASSEMBLY* NOZZLE BASE WITH RING NOZZLE TIP* 200, 201 & 206 NITRALLOY 40 * When ordering please specify number stamped on nozzle. See page 4. 3
4 Binks Model 21 (BRASS BODY) Automatic Spray Gun (Continued) Parts List When ordering, please specify Part No. ITEM PART NO. NO. DESCRIPTION QTY. 1 * Nozzle Air * Nozzle ** FLUID NEEDLE Locknut Plunger Washer Plunger Spring Plunger Plunger Leather Gland Packing ^ Spring Packing Follower Nut Air Packing ^ Packing Air Connection Air ^ Packing Air Valve Guide Air Valve Bonnet Screw Control Locknut Control Washer Control Locknut Body Side Port Control Stem Side Port Control... 1 ITEM PART NO. NO. DESCRIPTION QTY Washer Side Port Control Spring Side Port Control Pin Side Port Control Follower Side Port Control Side Port Control Complete ^ Follower Packing Screw Set Body Brass Valve Air Locknut Front ^ Spring Needle Valve ^ Packing Side Port Control Locknut Rear ^ Packing Needle Valve Nut Packing ^ Gasket Nozzle Ring Base Ring Ring OMX-88 Brush Cleaning (Not Shown)... 1 *When ordering, please specify number stamped on nozzle. See pages 2 and 4. ** When ordering, please specify gun model and number stamped on needle. See pages 2 and 4. Parts also available in Repair Kit ^Parts sold individually in packages of 5 (add -5 to part number). Gun wrench, is recommended for removing fluid nozzle. Please order separately. 4
5 Nozzle and Needle Selection Charts Type of Nozzle cfm at Max. Needle Nos. to be SprayED X Air Type Pattern for spray gun N nozzles PSI PSI PSI at 8 model 21 VERY THIN 63ss x 63P PE secs. Zahn 2 Cup 63Bss x 63PB PE A Wash primers, dyes, 66ss x 66SD SE stains, solvents, 66ss x 66SK SE water, inks 63Bss x 200 PI A THIN 63Ass x 63P PE A secs. Zahn 2 Cup 66ss x 66SK SE Sealer, lacquers, primers, inks, 63Bss x 200 PI A lubricants, zinc chromates, acrylics MEDIUM secs. Zahn 2 Cup 63Bss x 63PB PE A Synthetic enamels, varnishes, 66ss x 66SD SE shellacs, fillers, primers, epoxies, 66ss x 66SK SE urethanes, lubricants, 63Css x 200 PI A wax emulsions, enamels HEAVY (Cream-like) 67ss x 67PB PE Over 28 secs. 68ss x 68PB PE No. 4 Ford Cup 67ss x 206 PI VERY HEAVY 68ss x 68PB PE Texture coatings, 68ss x 206 PI Road marking paint 59Ass x 244 PI Bss x 252 PI Css x 262 PI ss x 206 PI ADHESIVES Waterbase white vinyl glues 63Bss x 66SD-3 PE Solvent base, neoprenes 67ss x 67PB PE (contact cement) 66ss x 66SD-3 PE CERAMICS Similar abrasive materials, glazes, 67VT x 67PD PE VT engobes, porcelain enamel 68VT x 68PB PE VT BUFFING COMPOUNDS 64VT x 64PA PE VT 67VT x 67PD PE VT CONCRETE CURING 66ss x 200 PI COMPOUNDS 67ss x 206 PI ss x 206 PI MULTICOLOR PAINTS 66ss x 200 PI ss x 206 PI TEFLONS 63Ass x 63PB PE A 66ss x 66SD PE HAMMERS 63ss X 63PB PE A 66ss X 63PB PE ss X 66SD PE WRINKLE ENAMELS 63Css x 63PB PE A 66ss x 63PB PE ZINC RICH COATINGS 66ss x 67PD PE VT x 67PB PE VT Note: PE - Pressure External SP - Siphon External PI - Pressure Internal 5
6 6 NOTES
7 NOTES 7
8 WARRANTY This product is covered by Binks 1 Year Limited Warranty. Binks Sales and Service: U.S.A./Canada Customer Service ITW Finishing Equipment Americas 195 Internationale Blvd. Glendale Heights, IL Toll Free Customer Service and Technical Support Toll Free Fax R-18 Revisions: (P2) Added warnings; (P4) Updated Parts List; (P8) Updated contact information. 3/ ITW Finishing Equipment Americas All rights reserved. Printed in U.S.A.
Binks Model 95 SPRAY GUN
Model 95 Signature Series Spray Gun This handheld gun is the premier spray gun in the Binks line. A combination of the three best industrial spray guns, Model 95 sets a new standard. 1 Binks Model 95 SPRAY
More informationBinks Model 7 SPRAY GUN (6100-XXXX-X)
Binks Model 7 SPRAY GUN (6100-XXXX-X) Your new Binks spray gun is exceptionally rugged in construction, and is built to stand up under hard, continuous use. However, like any other fine precision instrument,
More informationBinks Model 7 Spray Gun (6100-XXXX-X)
Binks Model 7 Spray Gun (6100-XXXX-X) Your new Binks spray gun is exceptionally rugged in construction, and is built to stand up under hard, continuous use. However, like any other fine precision instrument,
More informationBinks SV100 Conventional Suction Feed Spray Gun
Binks SV100 Conventional Suction Feed Spray Gun The following instructions provide the necessary information for the proper maintenance of the Binks SV100 suction feed spray gun. Please read and understand
More informationBinks SG-2 Plus TM Rotary 2 QT. PRESSURE CUP
Binks SG-2 Plus TM Rotary 2 QT. PRESSURE CUP Model No. 80-651 Rotary Agitator INTRODUCTION Binks SG-2 TM Plus Rotary 2 Qt. Pressure Cup is ideal for component spraying and industrial applications where
More informationBINKS MODEL 95 SPRAY GUN 6121-XXXX-X
SERVICE MANUAL EN BINKS MODEL 95 SPRAY GUN 6121-XXXX-X Model 95 Signature Series Spray Gun This handheld gun is the premier spray gun in the Binks line. A combination of the three best industrial spray
More informationBINKS MODEL 7 SPRAY GUN (6100-XXXX-X)
SERVICE MANUAL EN BINKS MODEL 7 SPRAY GUN (6100-XXXX-X) Your new Binks spray gun is exceptionally rugged in construction, and is built to stand up under hard, continuous use. However, like any other fine
More informationMODEL 7 SPRAY GUN (6100-XXXX-X)
SERVICE MANUAL MODEL 7 SPRAY GUN (6100-XXXX-X) Your new Binks spray gun is exceptionally rugged in construction, and is built to stand up under hard, continuous use. However, like any other fine precision
More informationBinks MACH 1PC HVLP SPRAY GUN FOR PLURAL COMPONENT CATALYST INJECTION
Binks MACH 1PC HVLP SPRAY GUN FOR PLURAL COMPONENT CATALYST INJECTION The Binks MACH PLURAL COMPONENT 1PC HVLP Gun is the lightest top quality high performance spray gun available today. You only have
More informationMODELS & (OBS) REMOTE FLUID PRESSURE REGULATORS (30 OZ./MIN. & 100 OZ./MIN.)
SERVICE MANUAL EN MODELS 84-598 & 84-599 (OBS) REMOTE FLUID PRESSURE REGULATORS (30 OZ./MIN. & 100 OZ./MIN.) INTRODUCTION The Binks Models 84-598 and 84-599 (obsolete) Remote Fluid Pressure Regulators
More informationBinks MACH 1 PCX HVLP SPRAY GUN
SERVICE MANUAL EN Binks MACH 1 PCX HVLP SPRAY GUN (For Plural Component Catalyst Injection) 77-2687-R3.1 (10/2015) 1 / 12 In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important
More informationBINKS SV100 HVLP PRESSURE FEED SPRAY GUN
SERVICE MANUAL EN BINKS SV100 HVLP PRESSURE FEED SPRAY GUN 7041-6931-1 The following instructions provide the necessary information for the proper maintenance of the Binks SV100 pressure feed spray gun.
More informationModel 2100 GW Plural. Replaces Part Sheet R. *Where atomization occurs entirely outside of the gun.
Model 2100 GW Plural Component Spray Gun General The 2100 GW gun is a lightweight, hand-held, plural component spray gun for spraying limited applications of two-component materials, such as gel-coats
More informationModel 2001 GW Plural. Replaces Part Sheet R-6. *Where atomization occurs entirely outside of the gun.
Model 200 GW Plural Component Spray Gun General The 200 GW gun is a lightweight, hand-held, plural component spray gun for spraying limited applications of two-component materials, such as gel-coats or
More information43P Airless Gun MODEL: DESCRIPTION
43P Airless Gun MODEL: 6730-0000-6 PURGE NOZZLE SAFETY LOCK SOLVENT DESCRIPTION The Binks Model 43P is a low to medium-volume plural component (spray and/or pour) dispensing device designed specifically
More informationBINKS SG-2 PLUS TM ROTARY 2 QT. PRESSURE CUP
SERVICE MANUAL EN INTRODUCTION BINKS SG-2 PLUS TM ROTARY 2 QT. PRESSURE CUP MODEL NO. 80-651 ROTARY AGITATOR Binks SG-2 TM Plus Rotary 2 Qt. Pressure Cup is ideal for component spraying and industrial
More informationBINKS WREN AIR BRUSHES MODELS A **, B, AND C ** OPERATING INSTRUCTIONS
SERVICE MANUAL BINKS WR AIR BRUSHES MODELS 59-10001 A **, 59-10002 B, AND 59-10021 C ** OPERATING INSTRUCTIONS **Models A and C are discontinued. (Shown for component replacement only.) IMPORTANT! DO NOT
More informationT1-Titanium HVLP Siphon Feed Spray Gun
T1-Titanium HVLP Siphon Feed Spray Gun THE SPRAY GUN PEOPLE FOR PRODUCT INFORMATION CALL: 1-800-742-7731 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.
More informationService Manual. DX70 Pump Packages
Service Manual DX70 Pump Packages Product This Product is designed for use with: Diaphragm Pumps DX70 Bare pump and packages Solvent and Water based Materials Suitable for use in hazardous area: Zone 1
More informationSAFETY MANUAL FOR FLAMMABLE PRODUCT TRANSFER
SAFETY MANUAL FOR FLAMMABLE PRODUCT TRANSFER SUPPLIMENT TO eom IMPORTANT READ THIS MANUAL BEFORE PRODUCT INSTALLATION, OPERATION, INSPECTION & MAINTENANCE Tougher and more rigid guidelines are being established
More informationCorrosion Control Equipment and Supplies
Distributed by: Corrosion Control Equipment and Supplies Houston Office: 248 McCarty Dr. Houston, TX 77029-1195 (713) 672-8251 Fax (713) 672-6636 1-800-CLEMTEX www.clemtex.com clemtex@clemtex.com Dallas
More informationAIRLESS 75M SPRAY GUN 7500 PSI
SERVICE MANUAL EN AIRLESS 75M SPRAY GUN 7500 PSI (0811-7500-4) The following instructions provide the necessary information for the proper operation and preventive maintenance of the Binks Airless 75M
More informationAir Consumption Recommended Usage Siphon Feed
Instructions/Parts Cobalt Non-HVLP Siphon/Pressure Feed Spray Gun 309998E Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. Maximum Air and Fluid
More informationT1-Titanium HVLP Pressure Feed Spray Gun
T1-Titanium HVLP Pressure Feed Spray Gun THE SPRAY GUN PEOPLE FOR PRODUCT INFORMATION CALL: 1-800-742-7731 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions.
More informationService Manual EN DX70. Pump Packages. Patent US R1.6 1/16
Service Manual EN DX70 Pump Packages Patent US 9447780 773201R1.6 1/16 www.carlisleft.com Product Description / Object of Declaration: Diaphragm Pumps DX70, DX200, DX2003 Bare pump and packages EN This
More informationBINKS SG-2 PLUS TM 2 QT. PRESSURE CUPS
SERVICE MANUAL EN BINKS SG-2 PLUS TM 2 QT. PRESSURE CUPS MODEL NO. 80-600 (STANDARD) MODEL NO. 80-601 (WITH OSCILLATING AGITATOR) INTRODUCTION Binks SG-2 Plus TM Pressure Cup is ideal for component spraying
More information5 Gallon Pressure Pot with HVLP Spray Gun and Hose
California Air Tools 5 Gallon Pressure Pot with HVLP Spray Gun and Hose Model No. 365 Technical Data Type of feed.pressure Maximum pressure in the tank... 0,413Mpa (60PSI) Working pressure in the tank.0,
More informationBINKS SV100 HVLP GRAVITY FEED SPRAY GUN
SERVICE MANUAL EN BINKS SV100 HVLP GRAVITY FEED SPRAY GUN 7042-6931-4 The following instructions provide the necessary information for the proper maintenance of the Binks SV100 gravity feed spray gun.
More informationService Manual DX70 Pump Packages
Service Manual DX70 Pump Packages 773201R1.3 1/16 Product Description / Object of Declaration: Diaphragm Pumps DX70, DX200, DX2003 Bare pump and packages This Product is designed for use with: Solvent
More information3/8" Dr. Air Butterfly Impact Wrench
8192106 3/8" Dr. Air Butterfly Impact Wrench Owner s Manual Read and understand all instructions before use. Retain this manual for future reference. Specifications Construction: Polished aluminum and
More informationSPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.
2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or
More informationHotspotter. Model WB-100 Professional Series. Assembly, Testing & Operating Instructions. Safety Information:
Hotspotter Model WB-100 Professional Series Assembly, Testing & Safety Information: Safety publications related to safe practice and use: CSA 2-94 U.S. Requirements for Hand-Held LP Torches for use with
More information7500 PSI Airless Spray Gun
7500 PSI Airless Spray Gun For trained, professional use only! Maximum working pressure: 7500 PSI 517 BAR 51.7 Mpa Models 1108-7500-2 & 1108-7500-4!! SAFETY, OPERATING AND MAINTENANCE INSTRUCTIONS INSIDE!!
More information3500 PSI Airless Spray Gun
3500 PSI Airless Spray Gun For trained, professional use only! Maximum working pressure: 3500 PSI 241 BAR 24.1 Mpa Models 1108-3500-2 & 1108-3500-4!! SAFETY, OPERATING AND MAINTENANCE INSTRUCTIONS INSIDE!!
More informationINTENDED USE TECHNICAL SPECIFICATIONS
1/2IN. HEAVY-DUTY AIR IMPACT WRENCH OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More informationBinks SG-2 Plus TM 2 QT. PRESSURE CUPS Model No (Standard) Model No (with OscillatingAgitator)
INTRODUCTION Binks SG-2 Plus TM Pressure Cup is ideal for component spraying and industrial applications where small batch production spraying is required. The 2 qt. capacity is sufficient to complete
More informationSpray Gun 134-A. 1 Liter High- Pressure Gel Coat. Usage Instructions & Parts List
1 Liter High- Pressure Gel Coat Spray Gun 134-A Usage Instructions & Parts List www.fibreglast.com 1.800.821.3283 385 Carr Drive Brookville, OH 45309 Operating Instructions & Suggestions This is a high
More informationROUGHNECK II Pumpless Drain
SERVICE BULLETIN SB4027 Rev. K 08/18 For Used Oil Only ROUGHNECK II Pumpless Drain Model #4110-022 FOR USED OIL ONLY (Black) For Antifreeze Only Model #4110-023 FOR USED ANTIFREEZE ONLY (Green) Patent
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 1-1/4 INCH BRAD NAILER Model: 7611 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationHeavy Fluid Air Spray Gun
Instructions Parts List Heavy Fluid Air Spray Gun 306494J 2000 psi (14.0 MPa, 140 bar) Maximum Fluid Working Pressure 100 psi (0.7 MPa, 7 bar) Maximum Air Working Pressure Part No. 204000, Series J With
More informationAC1810 / AC1810-A TECHNICAL SPECIFICATIONS. Operating Pressure psi ( kgs/cm²) [AC1810] Displacement. Net Weight
Technical Specifications Operating Instructions Maintenance Information Troubleshooting Guide Parts Diagrams AC1810 / AC1810-A THE EVOLUTION OF PERFECTION CAUTION: Before attempting to use or service this
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 2 INCH BRAD NAILER Model: 7555 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationService Manual DX70 Diaphragm Pump
Service Manual EN DX70 Diaphragm Pump 77-3200-R1.2 1/16 Product Description This Product is designed for use with: Diaphragm Pumps - DX70 Bare pump and packages Solvent and Water based Materials EN Suitable
More informationComposite Pistol-Type Air Needle Scaler OWNER S MANUAL
Composite Pistol-Type Air Needle Scaler OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may
More informationDWMT70778 Gravity Feed Touch-Up Spray Gun
snstruction ManUal DWMT70778 Gravity Feed Touch-Up Spray Gun DWMT70778 GRAVITY FEED TOUCH-UP SPRAY GUN FIG.1 K English A. Spray Gun Cup B. Material Filter C. Air Cap D. Horns E. Trigger F. Air Volume Control
More informationAIR COMPRESSOR. Failure to follow all instructions as listed below may result in electrical shock, fire, and/or serious personal injury.
2 GALLON AIR COMPRESSOR Model: 7517 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials
More information2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL
2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL Model: 52024 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement,
More informationBinks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI (RATIO 1:1)
Binks PNEUMATIC DIAPHRAGM PUMP DVP-GEMINI (RATIO 1:1) IMPORTANT Read and follow all instructions, recommendations and safety precautions before using this equipment. It is the responsibility of the employer
More informationModel ASSEMBLY and OPERATING INSTRUCTIONS
QUICK CHANGE AIR BRUSH KIT Model 93506 ASSEMBLY and OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 3491 Mission Oaks Blvd.,
More informationDX200 Stainless Steel Diaphragm Pump
Service Manual EN DX200 Stainless Steel Diaphragm Pump DX200SR DX200SN DX200SM 77-3211-R1.1 1/20 Product Description This Product is designed for use with: Diaphragm Pumps - DX70, DX200 Bare pump and packages
More informationOWNER S MANUAL. Page: 1 of 8
Air Needle Scaler OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal
More informationWARNING: HIGH PRESSURE.
Instructions Pole Gun with CleanShot Shut-Off Valve and Contractor In-line Valve For the application of architectural paints and coatings 3600 psi (248 bar, 24.8 MPa) Maximum Working Pressure Important
More informationOperation Manual: MODEL BBR PRESSURE/SIPHON FEED HAND GUN Important:
EN SB-E-A1-21 ISSUE. 2 Operation Manual: MODEL BBR PRESSURE/SIPHON FEED HAND GUN Important: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment DESCRIPTION This is a production
More information183S2 (STAINLESS STEEL) 15 GALLON ASME TANKS
SERVICE MANUAL EN 18S (STAINLESS STEEL) 15 GALLON ASME TANKS " NPT BOTTOM OUTLET TANKS Important: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment. Retain for future
More informationINSTRUCTIONS PARTS LIST
3066V-E INSTRUCTIONS PARTS LIST INSTRUCTIONS! This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. AQ Poppet Color Valve (3066-41-00A) 304 Stainless Steel Body Autoquip,
More informationEN MX432 32:1 Pump Systems for Air Assist & Airless Finishing Patent Pending
EN MX432 32:1 Pump Systems for Air Assist & Airless Finishing Patent Pending SPECIFICATIONS Ratio: 32:1 Maximum air inlet pressure: Maximum fluid pressure: Displacement per cycle: Output @ 60 cycles/min:
More informationMX412 12:1 Pump Systems for Air Assist & Airless Finishing
MX412 12:1 Pump Systems for Air Assist & Airless Finishing Patent Pending SPECIFICATIONS Ratio: 12:1 Maximum air inlet pressure: 8 bar [116 psi] Maximum fluid pressure: 96 bar [1390 psi] Displacement per
More informationINSTRUCTIONS PARTS LIST
INSTRUCTIONS PARTS LIST 307 890 This manual contains IMPORTANT WARNINGS AND INSTRUCTIONS READ AND RETAIN FOR REFERENCE STAINLESS STEEL, WATERBASE COMPATIBLE, LOW SHEAR FLUID PRESSURE REGULATOR 250 psi
More information2-Liter Pressure Cup. Instructions - Parts List C
Instructions - Parts List 2-Liter Pressure Cup 309925C Model 234413 50 psi (345 kpa, 3.4 bar) Maximum Fluid Pressure 160 psi (1.1 MPa, 11 bar) Maximum Air Inlet Pressure This manual contains important
More informationAIR-OPERATED DOUBLE DIAPHRAGM PUMP USER S MANUAL
00, 0, 000 00, 000, 00 A. TECHNICAL INFORMATION Model 00 Inlet/Outlet " Air Inlet /" 0 / 000 /" /" 00 /" /" 000 /" /" 00 /" /" Flow Rate GPM/ 0LPM GPM/ 0LPM GPM/ LPM GPM/ LPM GPM/ 0LPM GPM/ 0LPM Maximum
More informationREL-46 WARNING NOTICE 15 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD. Compatible with RELIABLE R15 and P Style dies. REL-46 Manual
OPERATORS ORS GUIDE REL-46 15 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD Compatible with RELIABLE R15 and P Style dies. RELIABLE EQUIPMENT & SERVICE CO., INC. 301 Ivyland Road Warminster, PA 18974
More informationMX412 12:1 PUMP SYSTEMS FOR AIR ASSIST & AIRLESS FINISHING
SERVICE MANUAL EN MX4 : PUMP SYSTEMS FOR AIR ASSIST & AIRLESS FINISHING Patent 7,03,8 SPECIFICATIONS Ratio: : Maximum air inlet pressure: Maximum fluid pressure: Displacement per cycle: Output @ 0 cycles/min:
More information4 ANGLE GRINDER MODEL NO: CAT 52 PART
4 ANGLE GRINDER 4 ANGLE GRINDER MODEL NO: CAT 52 PART No: 3110685 OPERATION & MAINTENANCE INSTRUCTIONS 0807 Fig.1 SPECIFICATIONS Model:...CAG52 Part Number:...3110685 Rated Wheel...Capacity: 4 x 1/4 (type
More informationREL-510H WARNING NOTICE 12 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD
OPERATORS ORS GUIDE REL-510H 12 TON SINGLE ACTING REMOTE HYDRAULIC CRIMPING HEAD Compatible with U style and RELIABLE R12 shell type 12 ton compression dies. RELIABLE EQUIPMENT & SERVICE CO., INC. 92 Steamwhistle
More informationDX :1. Stainless Steel Diaphragm Pump
Service Manual EN DX200-3 3:1 Stainless Steel Diaphragm Pump DX200-3SN DX200-3SP DX200-3SM 77-3212-R1.0 1/24 Product Description / Object of Declaration: Diaphragm Pumps - DX70, DX200, DX200-3 Bare pump
More informationYoke Block Instruction Manual
Yoke Block Instruction Manual ! WARNING IMPORTANT: READ MANUAL COMPLETELY BEFORE OPERATING THIS DEVICE This manual contains instructions on periodically required checks to be performed by the user. These
More information1/2 in. AIR IMPACT WRENCH (TWIN HAMMER)
1/2 in. AIR IMPACT WRENCH (TWIN HAMMER) WARNING Read Operator s Manual. Do not operate equipment until you have read this Operator s Manual for Safety, Assembly/Operation and Maintenance Instructions.
More informationTEM# Air Hammer Combo USER'S MANUAL
Air Tools TEM# 40 Air Hammer Combo USER'S MANUAL Read carefully and understand RULES FOR SAFE OPERATION and instructions before operating. Failure to follow the safety rules and other basic safety precautions
More informationCATALYZER TM 2K 10:1 RATIO Pump
PRODUCT INFORMATION CATALYZER TM 2K 10:1 RATIO Pump The C.A.Technologies CATALYZER is an Air Assist Airless 2 component formulator. Catalyst and base material are pumped into a mixing chamber at 10 : 1
More information!!!! SERVICE MANUAL PRESSURE POT 2 GALLON. Service Manual: LT Washington St 931 Progress Ave., #7
EXEL North America, Inc. EXEL Industrial Canada, Inc. 1310 Washington St 931 Progress Ave., #7 West Chicago, IL 60185 Scarborough ONT, M1G 3V5 Ph : (800) 573 5554 Ph : (800) 450 0655 Fx : (800) 664 1511
More informationLUBRICATOR ASSEMBLY AND OPERATING INSTRUCTIONS
AIR FILTER, REGULATOR AND LUBRICATOR 4035 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 004 by Harbor Freight
More informationInstructions Parts List. Table of Contents H. AIR OPERATED Valve Assembly
Instructions Parts List AIR OPERATED Valve Assembly 310503H This air-opened, air-closed valve can be used to control material flow of adhesive and sealant materials, such as two-part methacrylic adhesives,
More informationDISPENSING VALVE MODEL VDP100 INSTRUCTION MANUAL
DISPENSING VALVE MODEL VDP100 INSTRUCTION MANUAL CONTENTS 1. Safety - - - - - - - - - - - - - - - - - - - - - - - - - 3 2. Introduction - - - - - - - - - - - - - - - - - - - - - - - - - 5 3. Specification
More informationHydraulic Punch Drivers
SERVICE MANUAL 7804SB / 7806SB Quick Draw 7704SB / 7706SB Quick Draw Flex Quick Draw Hydraulic Punch Drivers Serial Codes AHJ and YZ Read and understand all of the instructions and safety information in
More informationOperation Manual Advanced-Conventional Pressure Feed Spraygun
SB-E-2-531 ISS.07 Operation Manual Advanced-Conventional Pressure Feed Spraygun E P 1-12 E Operation Manual Advanced Conventional Pressure Feed Spraygun Important Read and follow all instructions and Safety
More informationRhinoPro Cartridge Gun Manual
RhinoPro Cartridge Gun Manual RhinoPro Cartridge Gun 1500 with 750ml cartridges Table of Contents Application Instructions......................................... 1 Operating Instructions..........................................
More informationaccidents which arise due to non-observance of these instructions and the safety information herein.
3 GALLON PANCAKE COMPRESSOR Model: 50959 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationAdvanced Fluid Handling Cart Owner s Manual
Advanced Fluid Handling Cart IMPORTANT Please read this carefully and thoroughly before installing and operating your Advanced Fluid Handling Cart. Please retain this owner s manual for future reference
More informationOPERATION MANUAL NTF-15
OPERATION MANUAL NTF-15 Nitrogen Tire Filling Valve Stem Caps (Qty=200) Order P/N 436075 RTI Technologies, Inc 10 Innovation Drive York, PA 17402 800-468-2321 www.rtitech.com 035-81235-00 (Rev B) TABLE
More informationHEAVY-DUTY AIR RATCHET WRENCH OWNER S MANUAL
HEAVY-DUTY AIR RATCHET WRENCH OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in
More informationMX :1 Pump Systems for Air Assist & Airless Finishing
MX1212 12:1 Pump Systems for Air Assist & Airless Finishing Patent 7,603,855 SPECIFICATIONS Ratio: 12:1 Maximum air inlet pressure: Maximum fluid pressure: Displacement per cycle: Output @ 60 cycles/min:
More information97C COMPRESSOR KIT 12V PART NO C COMPRESSOR KIT 24V PART NO C COMPRESSOR KIT PART NO
97C COMPRESSOR KIT 12V PART NO. 00097 97C COMPRESSOR KIT 24V PART NO. 02497 98C COMPRESSOR KIT PART NO. 00098 97C 98C IMPORTANT: It is essential that you and any other operator of this product read and
More informationPDY TON HYDRAULIC CRIMPING TOOL WARNING
OPERATORS ORS GUIDE PDY-1220 12 TON HYDRAULIC CRIMPING TOOL All information found in this guide must be read and understood before use or testing of this tool. Failure to read and understand these warnings
More informationRS(H)10,15 USER MANUAL. Read the complete manual before installing and using the regulator.
RS(H)10,15 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to
More informationAssembly Drawing: W-311B-A01, or as applicable Parts List: W-311B-A01-1, or as applicable Special Tools: , , &
REDQ Regulators Model 411B Barstock Design Powreactor Dome Regulator OPERATION AND MAINTENANCE Contents Scope..............................1 Installation..........................1 General Description....................1
More information183G (GALVANIZED) 5, 10, AND 15 GALLON ASME TANKS
SERVICE MANUAL EN 8G (GALVANIZED) 5, 0, AND 5 GALLON ASME TANKS Important: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment. Retain for future reference. ACTUAL CAPACITIES
More information2.5 & 5.0 GALLON PRESSURE TANKS
2.5 & 5.0 GALLON PRESSURE TANKS Includes: MODEL 7025 MODEL 7026 MODEL 7027 MODEL 7028 2.5 Gallon Single Regulation (NON A.S.M.E.) 2.5 Gallon Dual Regulation (NON A.S.M.E.) 5.0 Gallon Single Regulation
More informationModel PSI Compressor with 3-Gallon Air Tank 12VDC
Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing
More informationLRS(H)4 USER MANUAL. Read the complete manual before installing and using the regulator.
LRS(H)4 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to the
More informationPAINT SPRAY GUN ASSEMBLY AND OPERATING INSTRUCTIONS
PAINT SPRAY GUN 30224 ASSEMBLY AND OPERATING INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 349 Mission Oaks Blvd., Camarillo, CA 930
More information750 Cable Cutter INSTRUCTION MANUAL
INSTRUCTION MANUAL 750 Cable Cutter Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Register this product at www.greenlee.com
More informationPressure Dump Valve Service Kit for Series 3000 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator
More informationPneumatic Wet Sander. (4,500 rpm) Operation Instruction
Pneumatic Wet Sander (4,500 rpm) Operation Instruction ON / OFF Safety Lever Features ON / OFF 4 6 3 5 2 5 3 6 7 4 Safety Lever 2 8 Rubber Sleeve Ergonomic handle comforts the users hand, its excellent
More information183G (GALVANIZED) AND 183S (STAINLESS STEEL) 2-GALLON ASME TANKS CAPACITY UP TO 2.8 GALLONS
SERVICE MANUAL EN 8G (GALVANIZED) AND 8S (STAINLESS STEEL) -GALLON ASME TANKS CAPACITY UP TO.8 GALLONS Important: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment. Retain
More informationInstallation Instructions Air Compressor Part # 2780, 2781
Note: It is essential that the operator of this product read and understand the contents of this manual before installing and using this product. Parts Included Qty Parts Included Qty Compressor 1 Coil
More information444C DUAL PERFORMANCE VALUE PACK
(Chrome) PART NO. 44432 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL
More informationYoke Block Instruction Manual
Yoke Block Instruction Manual ! WARNING IMPORTANT: READ MANUAL COMPLETELY BEFORE OPERATING THIS DEVICE This manual contains instructions on periodically required checks to be performed by the user. These
More informationSETTING UP THE MODEL 210B SRA
SETTING UP THE MODEL 210B SRA SAFETY PRECAUTIONS FOR THE MODEL 210B SRA System Under Pressure: Shut off air supply and disconnect air hose before disassembling or disconnecting parts. Flying Debris: During
More informationPRS(TC)4,8 USER MANUAL. Read the complete manual before installing and using the regulator.
PRS(TC)4,8 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to
More informationNeedle valve. Contents. User s Manual. (1) Be sure to read the following warranty clauses of our product 1. (2) General operating instructions 2
Serial No. H-V024-E-7 Needle valve User s Manual Contents (1) Be sure to read the following warranty clauses of our product 1 (2) General operating instructions 2 (3) General instructions for transportation,
More information