RECOMMENDED PERMIT CONDITIONS
|
|
- Elisabeth Curtis
- 5 years ago
- Views:
Transcription
1 TABLE OF CONTENTS Page SULFURYL FLUORIDE PERMIT CONDITIONS -- DECISION TABLE...C-81 RECOMMENDED PERMIT CONDITIONS NON-RESIDENTIAL FACILITES (<4500 LBS) Specific Conditions...C-82 RECOMMENDED PERMIT CONDITIONS FOR COMMODITY FUMIGATIONS & NON-RESIDENTIAL FACILITES (>4500 LBS) General Conditions...C-83 Specific Conditions...C-87 Charts and Tables...C-94 FINAL PERMIT CONDITIONS...C-99 C-80
2 PERMIT CONDITIONS DECSION TABLE SULFURYL FLUORIDE PERMIT CONDITIONS -- DECISION TABLE If the fumigation type is: And the total amount used will be: Your permit conditions start on: Non-Residential Processing & Storage Facilities Non-Residential Processing & Storage Facilities < 4500 lbs Page C-82 > 4500 lbs The CAC will refer your information to DPR. DPR will prepare a custom site plan for your fumigation. Commodity Any amount Page C-30 (Rev. 6-08) C- 81
3 Fumigation NON-RESIDENTIAL FUMIGATIONS <4500 LBS Permit Conditions for Non-Residential (Enclosed Areas), Less than or equal to 4500 lbs 1) General Requirement for Use of ProFume : Restricted material permits for the use of ProFume shall not be issued to a facility operator and/or pest control operator who has not received a Dow AgroSciences certification showing they have attended a ProFume stewardship training meeting. 2) Restricted Material Permit Conditions for Use in Nonresidential Facilities (Enclosed areas) a) For fumigations where less than or equal to 4500 lbs of sulfuryl fluoride will be applied within a 24 hour period, the following permit conditions apply: i) Buffer zone requirements: (1) Duration: A buffer zone must be maintained during fumigation and through the completion of aeration. (2) Distance: Use Table 1 to determine buffer zone distance based on the target fumigation concentration that will be maintained (oz SF/1000 ft3). (3) Occupation: The buffer zone extends from the edge of the fumigated building. There may not be any occupied structures within the buffer zone. Only persons supervising and performing fumigation activities are permitted in the buffer zone. Exception: Transit along public thoroughfares is allowed. ii) Aeration Requirements: (1) Minimum fumigant release height above ground level: 50 feet. (2) Aeration must be initiated during daylight hours: (a) Not later than one hour prior to sunset, and (b) Not earlier than one hour following sunrise. Table 1 Use table to determine the buffer zone distance from edge of the fumigation facility to the nearest occupied structure. Targeted Fumigation Conc. (oz/1000ft3) Buffer Zone Distance (ft) C- 82
4 GENERAL CONDITIONS Limits Special Site Requirements 1: Maximum Application Rate 2: Total Sulfuryl Fluoride 3: Other Types of Applications 4: Enclosed Area and Common Walls A maximum application rate of 8 pounds per 1000 cubic feet or the rate specified by the label may be used, whichever is less. The total amount of sulfuryl fluoride per work site must not exceed 1000 pounds in a 24-hour period. This permit condition does not apply to sulfuryl fluoride applications. The following types of fumigations are prohibited unless mitigation options are identified in the Work Site Plan: those inside an enclosed area with people present enclosures which share a common wall with another enclosed area with people present Examples: A tarpaulin fumigation inside a warehouse is prohibited. Using a chamber which shares a common wall with an office is prohibited. C-83
5 GENERAL CONDITIONS Fumigation Equipment and Introduction 5: Outside Introduction 6: Gas-tight Fumigant Lines Application from outside the enclosure through a closed system is required. Releasing fumigant from inside the enclosure is prohibited unless mitigation options are identified in the Work Site Plan. All fumigant lines must be gas-tight. Fumigant lines, valves, fittings, etc. which are routinely adjusted or changed must be checked for leaks after each adjustment. Examples: When changing sulfuryl fluoride cylinders, the connection between the introduction line and the cylinder must be checked for leaks. The cylinder valve must be checked for leaks after opening. 7: Test Equipment Seals 8: Test Equipment Exhaust 9: Fumigant Line Purge 10: Control Room Ventilation 11: Control Room Storage The enclosure must be sealed where instrument sampling lines pass through enclosure walls. Example: Fumiscope leads must be placed and the hole at the chamber or enclosure wall sealed prior to the fumigation. Exhaust from sampling equipment must be vented away from people and to outside air or back into the enclosure. When introducing fumigant from an enclosed control room, applicators must use nitrogen gas or compressed air to purge fumigant lines prior to changing cylinders. Enclosed control rooms must be mechanically ventilated during fumigation if workers are present. Sulfuryl fluoride cylinders must not be stored inside enclosed control rooms. C-84
6 GENERAL CONDITIONS Aeration Requirements NOTE: The following conditions pertain to aeration of the fumigation enclosure, not aeration of areas where commodities are stored, except when they are the same. 12: Aeration Initiation Persons who initiate aeration by manually breaking a seal must wear a self-contained breathing apparatus (SCBA). Exception: enclosures for which aeration is initiated remotely, such as chambers. Examples requiring SCBA: breaking seals on tarpaulin fumigations, opening sea/land container doors 13: Aeration During Daylight 14: Minimum Aeration Times 15: Testing Aeration Completeness Aeration must be initiated during daylight hours 1. Exception: Enclosures which aerate using an exhaust stack meeting the standard height requirements may exhaust at any time. Enclosures must be aerated for the following minimum duration: a. Four hours if mechanically ventilated using fans, or b. 12 hours if passively ventilated Note: The duration of the aeration period should not be confused with the time the aeration zone is in place. The aeration zone is in place for only the first portion of the aeration: four hours at most. The concentration of sulfuryl fluoride in the air spaces between the stacked commodity must be less than 1 ppm before the commodity can be moved from the enclosure. Testing of this air space must be done according to approved procedures. 1 Daylight hours = Not later than one hour prior to sunset and not earlier than one hour following sunrise. C-85
7 GENERAL CONDITIONS Storage Requirements Documentation Requirements 16: Enclosed Storage Areas Sulfuryl fluoride concentrations in enclosed areas (i.e., buildings, warehouses, silos, etc.) where fumigated commodities are stored must be less than 1 ppm before persons may enter. Testing of the air concentration must be done according to approved procedures. No individual may be inside the enclosed area for more than one hour in a 24-hour period. Note: This condition pertains to areas where commodities are stored, not the fumigation enclosure, except when they are the same. 17: Work Site Plan The enclosure operator and/or pest control business must complete or revise a Work Site Plan before receiving a permit. A completed Work Site Plan must be submitted to the CAC for evaluation before a Restricted Materials Permit will be issued. 18: Test Results Documentation The enclosure operator must keep records of all test results for two years and make them available to the CAC and workers (pursuant to Labor Code section 6408 and Cal-OSHA regulations Title 8, section 3204) upon request. C-86
8 SPECIFIC CONDITIONS Overview Fumigation Enclosure Types Buffer Zones There are specific conditions for each of six different types of fumigation enclosures. The enclosures are classified by the combination of two factors: the amount of fumigant the enclosure retains and the method used to aerate. There are two retention categories: pressure tested and retention tested/untested; and three aeration methods: standard height stack, minimum stack, and no stack. These two retention categories and three aeration categories give the six possible combinations of fumigation enclosures listed below: A1 - Pressure Tested/Standard Height Stack (e.g., quarantine or vacuum chamber) A2 - Pressure Tested/Minimum Stack (e.g., quarantine or vacuum chamber) A3 - Pressure Tested/No Stack (e.g., quarantine chamber without a stack) B1 - Retention Tested or Untested/Standard Height Stack (e.g., typical chamber) B2 - Retention Tested or Untested/Minimum Stack (e.g., "Butler" with short stack) B3 - Retention Tested or Untested/No Stack (e.g., tarp fumigation) The amount of time a person spends in areas around commodity fumigations must be limited in order to minimize exposure. Exposure is limited by restricting a person's access to or time spent in areas near enclosures being fumigated or aerated. The size of the buffer zones depends on which of the six types of enclosures is being used. For certain types of enclosures, the amount of sulfuryl fluoride used and retained in the enclosure also influences the size of the buffer zone. There are two types of buffer zones: treatment zone and aeration zone. There can be different sizes of treatment zones because of differences in exposure duration. For example, nearby workers would have a smaller treatment zone if they worked for 12 hours, compared to nearby residents who would have a treatment zone based on a 24-hour exposure. A summary of the treatment zones and aeration zones for the various types of fumigations appears in Chart 1. C-87
9 SPECIFIC CONDITIONS A1-Pressure Tested/ Standard Height Stack Enclosure Description A pressure tested/standard height enclosure is a vacuum chamber or has passed the USDA pressure test. The exhaust stack is at least 10 feet above the enclosure's highest point, at least 10 feet above any major obstruction within 200 feet of the stack and at least as tall as the appropriate value listed in Table 1. Examples: a quarantine chamber with a tall stack; a vacuum chamber with a tall stack. 19: Treatment Zone A treatment zone of 10 feet must be established around the enclosure during the fumigation treatment period. Only persons supervising and performing fumigation activities are permitted in the treatment zone during the treatment period. Exception: Limited transit is allowed if unavoidable. 20: Aeration Zone An aeration zone of 10 feet must be maintained around an enclosure during the first portion of the aeration period. Only persons supervising and performing fumigation activities are permitted in the aeration zone. Exception: Transit along public thoroughfares is allowed. The aeration zone must remain in place for the first four hours of aeration or until the exhaust concentration is less than 1 ppm. The aeration period itself may be of longer duration. Testing must be done according to approved procedures. 21: Vertical Stack Exhaust 22: Aeration During Daylight The stack must be vented vertically to the outside air. When exhausting, the top of the stack must be free of overhead obstructions. Does not apply. Aeration may occur at any time. C-88
10 SPECIFIC CONDITIONS A2-Pressure Tested/ Minimum Stack Enclosure Description A pressure tested/minimum stack enclosure is a vacuum chamber or has passed the USDA pressure test. The exhaust stack is at least 15 feet above ground and the exhaust exit velocity is at least 600 feet per minute. Examples: a quarantine chamber with a short stack; a vacuum chamber with a short stack. 19: Treatment Zone A treatment zone of 10 feet must be established around the enclosure during the fumigation treatment period. Only persons supervising and performing fumigation activities are permitted in the treatment zone during the treatment period. Exception: Limited transit is allowed if unavoidable. 20: Aeration Zone An aeration zone as specified in Table 3, page C-97, must be maintained around an enclosure during the first portion of the aeration period. Only persons supervising and performing fumigation activities are permitted in the aeration zone. Exception: Transit along public thoroughfares is allowed. The aeration zone must remain in place for the first four hours of aeration or until the exhaust concentration of sulfuryl fluoride is less than 1 ppm. The aeration period itself may be of longer duration. Testing must be done according to approved procedures. 21: Vertical Stack Exhaust 22: Aeration During Daylight The stack must be vented vertically to the outside air. When exhausting, the top of the stack must be free of overhead obstructions. Aeration must be initiated during daylight hours (see permit condition 13). (Rev. 6-08) C-89
11 SPECIFIC CONDITIONS A3-Pressure Tested/ No Stack Enclosure Description A pressure tested/no stack enclosure is a vacuum chamber or has passed the USDA pressure test, and either has no stack or the exhaust stack is less than 15 feet above ground or the exhaust exit velocity is less than 600 feet per minute. Example: a quarantine chamber with no stack. 19: Treatment Zone A treatment zone of 10 feet must be established around the enclosure during the fumigation treatment period. Only persons supervising and performing fumigation activities are permitted in the treatment zone during the treatment period. Exception: Limited transit is allowed if unavoidable. 20: Aeration Zone An aeration zone as specified in Table 4, page C-98, must be maintained around an enclosure during the first portion of the aeration period. Only persons supervising and performing fumigation activities are permitted in the aeration zone. Exception: Transit along public thoroughfares is allowed. The aeration zone must remain in place for the first four hours of aeration or until the exhaust concentration of sulfuryl fluoride is less than 1 ppm. The aeration period itself may be of longer duration. Testing must be done according to approved procedures. 21: Vertical Stack Exhaust 22: Aeration During Daylight Does not apply. Aeration must be initiated during daylight hours (see permit condition 13). (Rev. 6-08) C-90
12 SPECIFIC CONDITIONS B1-Retention Tested or Untested/ Standard Height Stack Enclosure Description A retention tested or untested/standard height stack enclosure may retain a large or small proportion of the and the exhaust stack is at least 10 feet above the enclosure's highest point, at least 10 feet above any building within 200 feet of the stack and at least as tall as the appropriate value listed in Table 1. Note: The size of the treatment zone may be minimized by measuring how well the enclosure fumigant and determining its loss ratio. This is done by performing a DPR-approved test procedure. Examples: a typical chamber with a tall stack, a "Butler" tank with a tall stack, a building with a tall stack. 19: Treatment Zone A treatment zone as specified in Table 2, page C-96, must be established around the enclosure during the fumigation treatment period. Only persons supervising and performing fumigation activities are permitted in the treatment zone during the treatment period. Exception: Limited transit is allowed if unavoidable. Different size zones may be calculated based on the duration of exposure and/or duration of the treatment period. For example, a treatment zone may be calculated for nearby workers based on a 12- hour work shift, and a separate treatment zone may be calculated for nearby residents based on 24-hour occupancy. 20: Aeration Zone An aeration zone of 10 feet must be maintained around an enclosure during the first portion of the aeration period. Only persons supervising and performing fumigation activities are permitted in the aeration zone. Exception: Transit along public thoroughfares is allowed. The aeration zone must remain in place for the first four hours of aeration or until the exhaust concentration is less than 1 ppm. The aeration period itself may be of longer duration. Testing must be done according to approved procedures. 21: Vertical Stack Exhaust 22: Aeration During Daylight The stack must be vented vertically to the outside air. When exhausting, the top of the stack must be free of overhead obstructions. Does not apply. Aeration may occur at any time. (Rev. 6-08) C-91
13 SPECIFIC CONDITIONS B2-Retention Tested or Untested/ Minimum Stack Enclosure Description A retention tested or untested/minimum stack enclosure may retain a large or small proportion of the fumigant. The exhaust stack is at least 15 feet above ground and the exhaust exit velocity is at least 600 feet per minute. Note: The size of the treatment zone may be minimized by measuring how well the enclosure retains fumigant and determining its loss ratio. This is done by performing a DPRapproved test procedure. Examples: a chamber with a short stack, a building exhausted through the roof. 19: Treatment Zone A treatment zone as specified in Table 2, page C-96, must be established around the enclosure during the fumigation treatment period. Only persons supervising and performing fumigation activities are permitted in the treatment zone during the treatment period. Exception: Limited transit is allowed if unavoidable. Different size zones may be calculated based on the duration of exposure and/or duration of the treatment period. For example, a treatment zone may be calculated for nearby workers based on a 12-hour work shift, and a separate treatment zone may be calculated for nearby residents based on 24-hour occupancy. 20: Aeration Zone An aeration zone as specified in Table 3, page C-97, must be maintained around an enclosure during the first portion of the aeration period. Only persons supervising and performing fumigation activities are permitted in the aeration zone. Exception: Transit along public thoroughfares is allowed. The aeration zone must remain in place for the first four hours of aeration or until the exhaust concentration of sulfuryl fluoride is less than 1 ppm. The aeration period itself may be of longer duration. Testing must be done according to approved procedures. 21: Vertical Stack Exhaust 22: Aeration During Daylight The stack must be vented vertically to the outside air. When exhausting, the top of the stack must be free of overhead obstructions. Aeration must be initiated during daylight hours (see permit condition 13). (Rev. 6-08) C-92
14 SPECIFIC CONDITIONS B3-Retention Tested or Untested/ No Stack Enclosure Description A retention tested or untested/no stack enclosure may retain a large or small proportion of the fumigant and either has no stack or the exhaust stack is less than 15 feet above ground or the exhaust exit velocity is less than 600 feet per minute. Note: The size of the buffer zones may be minimized by measuring how well the enclosure retains fumigant and determining its loss ratio. This is done by performing a DPR-approved test procedure. Examples: a typical sea/land containe, a building exhausted through open doors and windows, a typical tarpaulin fumigation. 19: Treatment Zone A treatment zone as specified in Table 2, page C-96, must be established around the enclosure during the fumigation treatment period. Only persons supervising and performing fumigation activities are permitted in the treatment zone during the treatment period. Exception: Limited transit is allowed if unavoidable. Different size zones may be calculated based on the duration of exposure and/or duration of the treatment period. For example, a treatment zone may be calculated for nearby workers based on a 12- hour work shift, and a separate treatment zone may be calculated for nearby residents based on 24-hour occupancy. 20: Aeration Zone An aeration zone as specified in Table 4, page C-98, must be maintained around an enclosure during the first portion of the aeration period. Only persons supervising and performing fumigation activities are permitted in the aeration zone. Exception: Transit along public thoroughfares is allowed. The aeration zone must remain in place for the first four hours of aeration or until the exhaust concentration of sulfuryl fluoride is less than 1 ppm. The aeration period itself may be of longer duration. Testing must be done according to approved procedures. 21: Vertical Stack Exhaust 22: Aeration During Daylight Does not apply. Aeration must be initiated during daylight hours (see permit condition 13). (Rev. 6-08) C-93
15 CHART 1 Summary of Buffer Zone Sizes Retention Category Aeration Method Class Treatment Zone Size Aeration Zone Size Aerate Daylight Hours Only Pressure Tested (USDA pressure test) Standard Height Stack (Table 1 requirements)* Minimum Stack (stack 15 ft above ground & exit velocity >600 ft/min) A1 10 feet 10 feet NO A2 10 feet Table 3 YES No Stack A3 10 feet Table 4 YES Retention Tested or Untested (DPR-approved test or no test) Standard Height Stack (Table 1 requirements)* Minimum Stack (stack 15 ft above ground & exit velocity >600 ft/min) B1 Table 2 10 feet NO B2 Table 2 Table 3 YES No Stack B3 Table 2 Table 4 YES * The stack must be at least 10 feet above the enclosure's highest point and at least 10 feet above any major obstruction within 200 feet of the stack and at least as tall as the appropriate value listed in Table 1. C-94
16 TABLE 1 Standard Height Exhaust Stack This table is used to determine the "standard height" (feet) of a stack. A "standard height" exhaust stack is one which is: 1. at least 10 feet above the enclosure's highest point, and 2. at least 10 feet above any major obstruction within 200 feet of the stack, and 3. at least as tall (above ground level) as the appropriate value in the table below Total Amount of Applied (pounds) at the Work Site in a 24-hour Period - ROUND UP Exit Velocity (feet per minute)* ROUND DOWN *Exit Velocity = Rated Fan Capacity (cubic feet per minute) Stack Cross-Sectional Area (square feet) area of circle = 3.14 radius 2 C-95
17 TABLE 2 Treatment Zone Sizes for Retention Tested and Untested Enclosures This table is used to determine the treatment zone size (feet) surrounding enclosures which are retention tested or untested. Consult with the CAC to determine the sizes for multiple fumigations in a 24-hour period. Concentration Lost (pounds per 1000 cubic feet)* ROUND UP Volume Fumigated in a 24-hour Period (cubic feet) ROUND UP * The Concentration Lost is calculated from the application rate, exposure duration, and loss ratio (proportion of fumigant leaked from the enclosure), according to the formula below. The exposure duration for workers is 12 hours or the treatment duration, whichever is less. The exposure duration for residents is the duration of treatment (24 hours maximum). The loss ratio is determined from a DPR approved test; for untested enclosures use Concentration Lost = [Application Rate (pounds per 1000 cubic feet)] [Exposure Duration (hours)] [Loss Ratio] C-96
18 RECOMMENDED PERMIT CONDITIONS TABLE 3 Aeration Zone Sizes for Minimum Stacks This table is used to determine the aeration zone size (feet) required during the aeration of enclosures with exhaust stacks having the following characteristics: 1. The top of the exhaust stack is at least 15 feet above ground level, and 2. The exit velocity is at least 600 feet per minute Exit Velocity = Rated Fan Capacity (cubic feet per minute) Stack Cross-Sectional Area (square feet) Total Retained in a 24-hour Period (pounds)* Aeration Zone (feet) ROUND UP * The Total Retained is calculated from the amount of fumigant, treatment duration and loss ratio (proportion of fumigant leaked from the enclosure), according to the formulas below. The loss ratio is determined from a DPRapproved test. Proportion Retained** = 1 [Treatment Duration (hours) Loss Ratio] **For untested enclosures, use 0.90 for the Proportion Retained Total Retained = [Amount of fumigant Applied in a 24 hour Period (pounds)] [Proportion Retained] C-97
19 RECOMMENDED PERMIT CONDITIONS TABLE 4 Aeration Zone Sizes for No Stacks This table is used to determine the aeration zone size (feet) of enclosures that have no stack. Consult with the CAC to determine the aeration zone size when aerating multiple enclosures in a 24-hour period. Concentration Retained (pounds per 1000 cubic feet)* ROUND UP Volume Aerated in a 24-hour Period (cubic feet) ROUND UP * The Concentration Retained is calculated from the rate, treatment duration, and loss ratio (proportion of fumigant leaked from the enclosure), according to the formulas below. The loss ratio is determined from a DPR-approved test. Proportion Retained** = 1 [Treatment Duration (hours) Loss Ratio] **For untested enclosures, use 0.90 for the Proportion Retained Concentration Retained = [Application Rate (pounds per 1000 cubic feet)] [Proportion Retained] C-98
20 FINAL PERMIT CONDITIONS GENERAL INFORMATION Fumigation Site: Permit Number: Address: City: Zip: Contact Person: Phone: (Facility Operator, Grower, QAC, QAL, etc.) Pest Control Business: Permit Number: Address: City: Zip: Contact Person: Phone: (QAL with the appropriate category) I VERIFY THAT THE ATTACHED PERMIT CONDITIONS WILL BE FOLLOWED Permit Applicant: (Facility Operator) Date: C-99
21 FINAL PERMIT CONDITIONS GENERAL INFORMATION 1: Maximum Application Rate Work Site Plan B.1 A maximum application rate of 8 pounds per 1000 cubic feet or the rate specified by the label may be used, whichever is less. See page C-87 for possible additional restrictions to comply with the buffer zones. 2: Total Sulfuryl Fluoride Work Site Plan B.2 The total amount of sulfuryl fluoride per work site must not exceed 1000 pounds in a 24-hour period. See page C-87 for possible additional restrictions to comply with the buffer zones. 3: Other Types of Applications Work Site Plan B.3 This permit condition does not apply to sulfuryl fluoride fumigations. 4: Enclosed Area and Common Walls Work Site Plan B.4 & 5 The following types of fumigations are prohibited: - those inside an enclosed area with people present - enclosures which share a common wall with another enclosed area with people present (Rev. 5/08) C-100
22 FINAL PERMIT CONDITIONS GENERAL INFORMATION 5: Outside Introduction Work Site Plan B.6 6: Gas-tight Fumigant Lines Work Site Plan B.7 7: Test Equipment Seals Work Site Plan B.8 8: Test Equipment Exhaust Work Site Plan B.9 Application from outside the enclosure through a closed system is required. Releasing sulfuryl fluoride from inside the enclosure is prohibited. All fumigant lines must be gas-tight. Fumigant lines, valves, fittings, etc. which are routinely adjusted or changed must be checked for leaks after each adjustment. The enclosure must be sealed where instrument sampling lines pass through enclosure walls. Exhaust from sampling equipment must be vented away from people and to outside air or back into the enclosure. C-101
23 FINAL PERMIT CONDITIONS GENERAL INFORMATION 9: Fumigant Line Purge Work Site Plan B.10 10: Control Room Ventilation Work Site Plan B.11 11: Control Room Storage Work Site Plan B.12 When introducing sulfuryl fluoride from an enclosed control room, applicators must use nitrogen gas or compressed air to purge fumigant lines prior to changing cylinders. Enclosed control rooms must be mechanically ventilated during fumigation if workers are present. Sulfuryl fluoride cylinders must not be stored inside enclosed control rooms. C-102
24 FINAL PERMIT CONDITIONS GENERAL INFORMATION 12: Aeration Initiation Work Site Plan B.13 13: Aeration During Daylight Work Site Plan D.3 Persons who initiate aeration by manually breaking a seal must wear a self-contained breathing apparatus (SCBA). Exception: Enclosures for which aeration is initiated remotely, such as chambers. Aeration must be initiated during daylight hours. Exception: Enclosures which aerate using an exhaust stack meeting the standard height requirements may exhaust at any time. 14: Minimum Aeration Times Enclosures must be aerated for the following minimum duration: a. 4 hours if mechanically ventilated using fans, or b. 12 hours if passively ventilated Work Site Plan B.14 & B.15 15: Testing Aeration Completeness Work Site Plan B.16 The concentration of sulfuryl fluoride in the air spaces between the stacked commodity must be less than 1 ppm before the commodity can be moved from the enclosure. Testing of this air space must be done according to approved procedures. C-103
25 FINAL PERMIT CONDITIONS GENERAL INFORMATION 16: Enclosed Storage Areas Work Site Plan B.17 & B.18 Sulfuryl fluoride concentrations in enclosed areas (i.e., buildings, warehouses, silos, etc.) where fumigated commodities are stored must be less than 1 ppm before persons may enter. Testing of the air concentration must be done according to approved procedures. No individual may be inside the enclosed area for more than one hour in a 24-hour period. 17: Work Site Plan The enclosure operator and/or pest control business must complete or revise a Work Site Plan before receiving a permit. 18: Test Results Documentation Work Site Plan B.19 The enclosure operator must keep records of all test results for 2 years and make them available to the County Agricultural Commissioner and workers upon request. C-104
26 FINAL PERMIT CONDITIONS GENERAL INFORMATION This part needs to be completed for each enclosure. Enclosure Identification/Description: (check one) A1 - Pressure Tested/Standard Height Stack Work Site Plan C.1-11 A2 - Pressure Tested/Minimum Stack A3 - Pressure Tested/No Stack B1 - Retention Tested or Untested/Standard Height Stack B2 - Retention Tested or Untested/Minimum Stack B3 - Retention Tested or Untested/No Stack Ancillary Buffer Zone Requirements: Maximum Application Rate: Treatment Duration: Maximum Fumigated Volume: Other Enclosures Which May Be Used Within 24 hrs: 19: Treatment Zone Work Site Plan C : Aeration Zone Work Site Plan C : Vertical Stack Exhaust Work Site Plan D.1, D.2 A treatment zone of feet must be established around the enclosure during the fumigation treatment period. Only persons supervising and performing fumigation activities are permitted in the treatment zone during the treatment period. A separate treatment zone of feet for workers may be used. An aeration zone of feet must be maintained around an enclosure during the first portion of the aeration period. Only persons supervising and performing fumigation activities are permitted in the aeration zone. The aeration zone must remain in place for the first four hours of aeration or until the exhaust concentration is less than 1 ppm. The stack must be vented vertically to the outside air. When exhausting, the top of the stack must be free of overhead obstructions. C-105
Merced County Agricultural Commissioner s. Commodity Fumigation Permit Conditions
Merced County Agricultural Commissioner s Commodity Fumigation Permit Conditions Overview Introduction This section provides information on Commodity Fumigation. In this section This section provides the
METH-O-GAS 100 COMMODITY FUMIGANT. ACTIVE INGREDIENT: Methyl Bromide 100% This product weighs 14.4 pounds per gallon. KEEP OUT OF REACH OF CHILDREN
RESTRICTED USE PESTICIDE DUE TO ACUTE TOXICITY For retail sale to and use by Certifi ed Applicators or persons under their direct supervision, and only for those uses covered by the Certifi ed Applicator
TYPICAL TOXIC GAS SYSTEM INSPECTION VIOLATIONS
TYPICAL TOXIC GAS SYSTEM INSPECTION VIOLATIONS The following is a list of typical violations often found by inspectors and a generic solution. You can use this list to improve the safety of your facility,
Methyl Bromide Quarantine Fumigant
RESTRICTED USE PESTICIDE Due to Acute Toxicity For retail sale to and use by certified applicators or persons under their direct supervision and only for those uses covered by the certified applicator
Section 1.3: PRESSURE VESSEL COMPONENTS AND SYSTEMS AND COMPRESSED GAS CYLINDERS
Section 1.3: PRESSURE VESSEL COMPONENTS AND SYSTEMS AND COMPRESSED GAS CYLINDERS TABLE OF CONTENTS Page A. Regulations, Standards and References 1.3-2 B. Scope 1.3-2 C. Design Features for the Storage
Gas Cabinets and Valve Manifold Boxes: Applying CGA G13- Rev 2015 to Gas Delivery Equipment
Gas Cabinets and Valve Manifold Boxes: Applying CGA G13- Rev 2015 to Gas Delivery Equipment The Standard Governing the Storage & Use of Silane: Compressed Gas Association s Publication CGA G-13 2015: Storage
Mitigation Starts With Design! Continues with Safe Operation, Mechanical Integrity and Training!
P.S.I.G. Mitigation Starts With Design! Continues with Safe Operation, Mechanical Integrity and Training! Last Unfortunately is When It Goes Wrong! The Failure! The Release! Loss of Product or Production
Marshall Municipal Utilities CONFINED SPACE ENTRY Effective January 1, 2011
Marshall Municipal Utilities CONFINED SPACE ENTRY Effective January 1, 2011 Purpose Marshall Municipal Utilities confined space entry program is designed to protect employees from the recognized hazards
Methyl Bromide Quarantine Fumigant
RESTRICTED USE PESTICIDE Due To Acute Toxicity For retail sale to and use by certified applicators or persons under their direct supervision and only for those uses covered by the certified applicator
Laboratory Ventilation. Environmental, Health, and Safety
No.: BCF020.054 Page: 1 of 7 RECORD OF REVISIONS Date Rev # Details of Change 09/13 1 Updated job titles to reflect ICON job descriptions. Added a definition for Approved Ventilation Contractor and included
Q. What is the first thing you should do when you detect a pest problem? A. Identify the pest.
Unit 1: Introduction Q. In what situations are fumigants commonly used? We rely on fumigants to treat processing plants, boxcars, and ships. Fumigation is one of the quickest and most effective ways to
TABLE OF CONTENTS PART 2 - CONFINED SPACES
May 11, 2006 TABLE OF CONTENTS PART 2 - CONFINED SPACES Page DEFINITIONS... 2-1 GENERAL... 2-2 RESPONSIBILITIES... 2-2 HAZARD ASSESSMENT AND WORK PROCEDURES... 2-3 IDENTIFICATION AND ENTRY PERMITS... 2-3
Standard Pneumatic Test Procedure Requirements for Piping Systems
the pressure equipment safety authority Standard Pneumatic Test Procedure Requirements for Piping Systems AB-522 Edition 2, Rev. 1 Issued 2016-10-24 Table of Contents FOREWORD... 1 1.0 INTRODUCTION...
TEMPLE UNIVERSITY ENVIRONMENTAL HEALTH AND RADIATION SAFETY
Page 1 of 9 ISSUED: 5/00 REVISED: 08/06 Introduction Purpose: In accordance with applicable regulations and Temple University, this policy was developed to minimize exposure to Ethylene Oxide. Applicability
WORKPLACE SAFETY INSPECTIONS TABLE OF CONTENTS INTRODUCTION...2 OBJECTIVE...2 REFERENCES...2 PREREQUISITES...2 PRECAUTIONS...2 CHECKLISTS...
REVISION 0 PAGE 1 OF 8 TABLE OF CONTENTS SECTION PAGE INTRODUCTION...2 OBJECTIVE...2 REFERENCES...2 PREREQUISITES...2 PRECAUTIONS...2 CHECKLISTS...2 PROCEDURE...3 Responsibilities...3 Work Area Safety
Methyl bromide fumigation methodology. Version 2.0
Methyl bromide fumigation methodology Version 2.0 Produced by the secretariat of the International cargo Cooperative Biosecurity Arrangement adopted 11 May 2018 Version 2.0 The ICCBA secretariat encourages
Cylinderized Phosphine Fumigant
July 14, 2014 Cylinderized Phosphine Fumigant ECO2FUME Fumigant Gas 1 Presentation Outline 1. Stewardship 2. Product Information 3. Dispensing 4. Benefits of Cylinderized Phosphine 5. Applications Scenarios
FIRST AID. Take off contaminated clothing. Rinse skin immediately with plenty of water for minutes.
92448-1_Inbrom 100 Quarantine Fumigant_20180716_1_92448_.pdf RESTRICTED USE PESTICIDE Due to Acute Toxicity For retail sale to and use by certified applicators or persons under their direct supervision
ATTACHMENT O WIPP MINE VENTILATION RATE MONITORING PLAN
ATTACHMENT O WIPP MINE VENTILATION RATE MONITORING PLAN (This page intentionally blank) ATTACHMENT O WIPP MINE VENTILATION RATE MONITORING PLAN TABLE OF CONTENTS O- Definitions... O- Objective... O- Design
SST Installation Guide. Brenda Land, Sanitary Engineer
Recreation Management TechTips United States Department of Agriculture Forest Service Technology & Development Program May 2003 2300 0323 1303 SDTDC SST Installation Guide Brenda Land, Sanitary Engineer
SUBSTATION MAINTENANCE ELECTRICAL OPERATING PROCEDURE
Page 1 of 6 A. PURPOSE AND SCOPE This procedure establishes safe working practices for handling sulfur hexafluoride (SF 6 ) gas and release minimization practices. This document also specifies methods
Piped Air SCBA Refilling System Standard
WALT WHITE Fire Chief 5770 Freeport Blvd., Suite 200 Sacramento, CA 95822-3516 Ph: (916) 808-1300 Fax: (916) 808-1629 www.sacfire.org Piped Air SCBA Refilling System Standard SCOPE: This specification
Instruction Manual VCG-6
Specifications Amps / Volts requirements 400 ma @ 24 VDC Propane pressure (VCG-6LP) 11 WC / 2.8 kpa Natural Gas pressure (VCG-6NG) 4.5 WC / 1.15 kpa Cu ft per hour / CO2 3-6 SCFH BTU Rating (Variable)
Intertek Testing Services Taiwan Ltd.
1) The testing results relate only to the items tested. Page 2 of 21 2) The test report shall not be reproduced except in full, without written approval of the laboratory. 3) This test report only allows
Cal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848
Cal/OSHA Gas Systems for Welding GAS WELDING Cal/OSHA T8 CCR 1536 Cal/OSHA T8 CCR 4799 Cal/OSHA T8 CCR 4845 Cal/OSHA T8 CCR 4848 When performing gas welding, the following precautions, work procedures,
PLEASE DO NOT WRITE ON THIS EXAM
PLEASE DO NOT WRITE ON THIS EXAM Your instructor will provide you with the registration form you completed at the beginning of this course. Please use the back of the signed registration form to record
PLEASE DO NOT WRITE ON THIS EXAM
PLEASE DO NOT WRITE ON THIS EXAM Your instructor will provide you with the registration form you completed at the beginning of this course. Please use the back of the signed registration form to record
Occupational Safety and Health Administration
Occupational Safety and Health Administration Standard Number: 1910.134; 1910.1053; 1910.1200; 1926.1153; 1926.1153(c); 1926.1153(c)(1); 1926.1153(d); 1926.1153(d)(1); 1926.1153(d)(2); 1926.1153(d)(2)(iii)(B);
Exhibit 4. Determination of Static Pressure Performance of the Healy Clean Air Separator (Executive Orders VR-201-N and VR-202-N)
1 APPLICABILITY Exhibit 4 Determination of Static Pressure Performance of the Healy Clean Air Separator (Executive Orders VR-201-N and VR-202-N) Definitions common to all certification and test procedures
USEPA WORKER PROTECTION STANDARD REVISIONS. Department of Pesticide Regulation 2016
USEPA WORKER PROTECTION STANDARD REVISIONS Department of Pesticide Regulation 2016 USEPA CHANGES WORKER PROTECTION STANDARD Scope: Agricultural workers Pesticide handlers Pesticides for the production
Additional requirements for all types of entry are described in Section Determining the Applicable Entry Method
ENVIRONMENT, SAFETY & HEALTH DIVISION Chapter 6: Confined Space Entry Procedures Product ID: 155 Revision ID: 1948 Date published: 15 September 2017 Date effective: 15 September 2017 URL: http://www-group.slac.stanford.edu/esh/eshmanual/references/confinedprocedentry.pdf
1 Exam Prep NFPA 99 Health Care Facilities Questions and Answers (Plumbing Contractor)
1 Exam Prep NFPA 99 Health Care Facilities Questions and Answers (Plumbing Contractor) 1. According to NFPA 99, SCFM is an acronym for. a) Surface Conditions at Fahrenheit Mercury b) Standard Conditions
Recommended Facilitator Notes: (read the following text out-loud to participants while showing this slide)
Slide 1 Confined Space Entry for General Industry These materials have been developed based on applicable federal laws and regulations in place at the time the materials were created. The program is being
IGI CARBON DIOXIDE KEEP OUT OF REACH OF CHILDREN WARNING. ACTIVE INGREDIENT: Carbon Dioxide % OTHER INGREDIENTS: % TOTAL
IGI CARBON DIOXIDE ACTIVE INGREDIENT: Carbon Dioxide... 99.9% OTHER INGREDIENTS:... 0.1% TOTAL... 100.0% If inhaled KEEP OUT OF REACH OF CHILDREN WARNING FIRST AID Move person to fresh air. If person is
Respiratory Protection Self-Inspection Checklist
Respiratory Protection Self-Inspection Checklist Guidelines: This checklist applies to the use of either atmosphere-supplying or air-purifying respirators being worn, voluntarily or otherwise, for comfort
IDEM Indiana Department of Environmental Management Office of Land Quality P.O. Box 6015 Indianapolis, IN OLQ PH: (317)
IDEM Indiana Department of Environmental Management Office of Land Quality P.O. Box 6015 Indianapolis, IN 46206-6015 OLQ PH: (317) 232-8941 Information SUBPART CC AIR EMISSION STANDARDS (40 CFR 264.1080
Respiratory Protection Self Inspection Checklist
Optional Information Name of School: Date of Inspection: Vocational Program/Course/Room: Signature of Inspector: Respiratory Protection Self Inspection Checklist Guidelines: This checklist covers some
HEALTH AND SAFETY MANUAL
HEALTH AND SAFETY MANUAL Title: Hydrogen Sulfide (H 2 S) Safety Approved by: Greg Savoy Rev. 4/1/08 1 Purpose/Scope: The purpose of this program is to establish minimum requirements for site specific H
U.S. Patent No. 7,922,246. Patents Pending
U.S. Patent No. 7,922,246 Patents Pending 2 Table of Contents Page General Information... 3 Warnings and Cautions... 4 Tools... 6 SmartDock Parts... 6 Initial Set-Up and Adjustment... 7 Select Valve Retaining
Mobile Breathing Air Systems
FAMA BUYER S GUIDE TC053 Prepared by the FAMA Body Subcommittee This guide does not endorse any manufacturer or product Page 1 of 14 Contents Introduction... 3 Overview... 4 Mobile Breathing Air System
Confined Spaces. 1. Definition Permit/Non-Permit
1. Definition Permit/Non-Permit Confined Spaces A. Non-Permit Required Confined Space: 1. Large enough and so configured that an employee can bodily enter and perform assigned duties. 2. Has a limited
SECTION LEAD-PAINT REMOVAL
SECTION 02090 LEAD-PAINT REMOVAL PART 1 - GENERAL 1.1 DESCRIPTION This section specifies abatement and disposal of lead-based paint (LBP) and controls needed to limit occupational and environmental exposure
Half Facepiece Respirator Assembly 5000 Series, Dual Cartridge, Disposable
Half Facepiece Respirator Assembly 5000 Series, Dual Cartridge, Disposable User Instructions for 3M Organic Vapor Respirator Assembly 5101/5201/5301; 3M Organic Vapor/Acid Gas Respirator Assembly 5103/5203/5303;
Focus on VOC Emissions Reduction Using an Oxygen Based Inerting Control System For Inert Gas Blanketing of Chemical Process Vessels
Inerting Control Systems by NTRON PROCESS ANALYZER DIVISION of NEUTRONICS INC. EXTON. PA. 19341 RJN Rev. A June 2001 Focus on VOC Emissions Reduction Using an Oxygen Based Inerting Control System For Inert
Scope: This plan applies to all personnel, including contractors, who enter or work in confined spaces, or supervise such activities.
11/13/1995 4 5/20/2013 1 of 10 Authority and Scope Regulation: 29 CFR 1910.146 Scope: This plan applies to all personnel, including contractors, who enter or work in confined spaces, or supervise such
UNIVERSITY OF RHODE ISLAND DEPARTMENT OF SAFETY & RISK MANAGEMENT STANDARD OPERATING PROCEDURE
UNIVERSITY OF RHODE ISLAND DEPARTMENT OF SAFETY & RISK MANAGEMENT STANDARD OPERATING PROCEDURE SUBJECT: Confined Space Policy Number: 00-2-2 POLICY: This policy delineates the procedure that will be followed
L 100. Bubble-Tube Level System. Installation, Operation and Maintenance Instructions
L 100 Bubble-Tube Level System Installation, Operation and Maintenance Instructions Figure 1 Contents Section Description Page 1.0 Introduction 2 2.0 Specifications 3 3.0 Installation 3 4.0 Warranty 6
pumping gases JET PUMP TECHNICAL DATA
Section 1000 Bulletin 100 Issued 9/87 Replaces 7/84 JET PUMP TECHNICAL DATA pumping gases This technical bulletin includes general information about Penberthy Jet Pumps plus specific details for selecting
Nitrogen System Contamination
Nitrogen System Contamination Lessons Learned Volume 05 Issue 03 2005 USW Nitrogen System Contamination Purpose To conduct a small group lessons learned activity to share information gained from incident
AFAS METHYL BROMIDE FUMIGATION STANDARD
The Australian Fumigation Accreditation Scheme (AFAS) AFAS METHYL BROMIDE FUMIGATION STANDARD Version 2.3 August 2015 Page 1 CONTENTS Fumigant considerations risk assessment, commodity, dosage, temperature...
PERMIT-REQUIRED CONFINED SPACES PROGRAM
PERMIT-REQUIRED CONFINED SPACES PROGRAM On January 14, 1993, OSHA established safety requirements to protect employees from the hazards of entry into permit-required confined spaces. It is essential to
CITY AND COUNTY OF DENVER POLICY DENVER FIRE DEPARTMENT
Reference: IFC, Denver Amendments, NFPA Approved: Joseph L. Gonzales, Division Chief, Fire Prevention and Investigation Division Number: IFC- 3001-1 Effective Date: February 1, 2012 Page 1 of 5 This policy
INSTRUCTIONS FOR COMPLETING FORM H-9 STATEWIDE RULE 36 CERTIFICATE OF COMPLIANCE
INSTRUCTIONS FOR COMPLETING FORM H-9 STATEWIDE RULE 36 CERTIFICATE OF COMPLIANCE 1. The certificate of compliance shall certify that operator has complied, or will comply, with applicable provisions of
Confined Space Entry Considerations April 2016
RiskTopics Confined Space Entry Considerations April 2016 This RiskTopic outlines considerations for confined space entry and discusses the OSHA Confined Space Standard for General Industry. Introduction
Hazardous Waste Training Plan. Supersedes: 02/15/16 (Rev.02) Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager
Procedure No.: PA-033-0006 Page: 1 of 19 Port Arthur, TX. Reviewed: 02/18 Effective: 02/06/18 (Rev.03) Supersedes: 02/15/16 Preparer: Owner: Approver: EHS Team Member EHS Team Member EHS Manager Document
INGROUND OR ABOVE GROUND POOL. APPROVALS REQUIRED (Check here if): Well Septic
Est. Cost $ HI# Exp Date GENERAL LAND USE CHECKLIST TOWN OF WILTON, CONNECTICUT Property Address Parcel # Tax Collector Approval Date Applicant s Name Applicant s Address Phone # Year Built (verified)
HOT OILING OPERATIONS ALL HSE PRC 172. Approved By: Manager, HSE Performance Assurance. Table of Contents
Owner: HSE Performance Assurance ALL HSE PRC 172 Approved By: Manager, HSE Performance Assurance Retention Code: CG01 CA Revised: March 2015 Review Frequency: Five years or less Table of Contents 1.0 Purpose...
CONFINED SPACE PROGRAM
CONFINED SPACE PROGRAM I. Purpose This Confined Space Program has been developed in accordance with the Occupational Safety and Health Administration (OSHA) regulations 29 CFR 1910.146. The purpose of
Compressed Gas Cylinders - Guideline
Environmental Health and Safety Compressed Gas Cylinders - Guideline Date of Issuance: 1/10/18 Revision Number: Initial Revision Date: Prepared by: EH&S 1. Purpose Carnegie Mellon University has developed
FLAMMABLE GASES AND FLAMMABLE CRYOGENIC FLUIDS
CHAPTER 35 FLAMMABLE GASES AND FLAMMABLE CRYOGENIC FLUIDS SECTION 3501 GENERAL 3501.1 Scope. The storage and use of flammable gases shall be in accordance with this chapter. Compressed gases shall also
WORKPLACE SAFETY AND HEALTH ACT (CHAPTER 354A) WORKPLACE SAFETY AND HEALTH (CONFINED SPACES) REGULATIONS 2009
1 of 9 08/06/2012 10:25 Workplace Safety and Health (Confined Spaces) Regulations 2009 Enacting Formula Part I PRELIMINARY 1 Citation and commencement 2 Definitions 3 Application Part II GENERAL PROVISIONS
Working in Gas Hazard Areas
/ Health & Safety OPERATIONS STANDARDS Ref.: Aperam Safety ST 012 Working in Gas Hazard Areas Issue: 15.05.2012 Vers.: v0 Rev.: AM Safety ST 012 v1.2 08.05.2012 Working in Gas Hazard Areas Controlled Updated
CTG Certification Protocol -- Version 3.0 SUMMARY
Date of Test: Test Report Number: SUMMARY Date of Prior Certification: Certified by: Re-certification Due Date: Unit Description: Make : Model: Serial Number: Location: CERTIFIER INFORMATION Name: Client
Procedure: Confined space safety
Purpose To define the requirements for the control of hazards associated with the use of confined spaces at the Australian National University to ensure compliance with the Work Health and Safety Act 2011
Vision Painting Inc Safety Management System
Abrasive Blasting 1. PURPOSE The purpose of this program is to provide training and qualification guidelines for the safe operation of Abrasive Blasting. The Safety Officer is responsible for facilitating
3M Steri-Vac Sterilizer/Aerator GSX Series. For Life Science Applications. Product. Profile
M Steri-Vac Sterilizer/Aerator GSX Series Product Profile Product Profile M Steri-Vac Sterilizer/Aerator GSX Series ethylene oxide (EO) sterilizer/aerators are designed to be used with M Steri-Gas EO Gas
GEN-1e CO2 Generator OVERVIEW INSTALLATION PROPANE GENERATORS ONLY NATURAL GAS GENERATORS ONLY
GEN-1e CO2 Generator Custom Automated Products offers economical and safe carbon dioxide generators. They produce CO2 by burning either propane or natural gas. We have designed our CO2 generator to allow
Fumigation Safety. Inhalation is the most common route of exposure to fumigants (levitt-safety.com)
Kentucky Pesticide Education Program copyright 2016 University of Kentucky Department of Entomology Fumigation Safety Inhalation is the most dangerous and common route of exposure to fumigants. Most are
CONFINED SPACE ENTRY PROGRAM FOR GOUCHER COLLEGE
I. INTRODUCTION CONFINED SPACE ENTRY PROGRAM FOR GOUCHER COLLEGE The Goucher College campus has confined spaces that, due to various chemical and physical properties, may cause death or serious injury
Heat Stress Policy UFEHS-SAFE-04/04/01 Environmental Health and Safety Finance and Administration University of Florida
Heat Stress Policy UFEHS-SAFE-04/04/01 Environmental Health and Safety Finance and Administration University of Florida OBJECTIVE The objective of this policy is to reduce the risk of illness, injury or
University of Minnesota Nano Center Standard Operating Procedure
University of Minnesota Nano Center Standard Operating Procedure Equipment Name: Controlled Atmosphere Glove Box Model: Labconco Protector Location: PAN 185 Badger Name: Not on Badger Revision Number:
Safety Regulations and Procedures GENERAL SAFETY Confined Spaces - S New 11/96. To provide guidance for the safe entry of confined spaces.
CONFINED SPACES PURPOSE REGULATION To provide guidance for the safe entry of confined spaces. Washington Administrative Code - WAC 296-62, Part 'M,' Confined Spaces. RESPONSIBILITY Safety Services test
Title: Standard Operating Procedure for Dasibi Model 5008 Gas Dilution Calibrator
Procedure No: SOP-034 Revision No: 1.0 Revised Dec. 29, 2010 Page No.: 1 of 10 1. INTRODUCTION AND SCOPE This procedure is intended to describe the operations of the Dasibi model 5008 calibrator. The Dasibi
Inflammable Gases Regulations 1962
Inflammable Gases Regulations 1962 GN 32/1962 21st April Regulations made by the Governor under Section 3 of the Inflammable Liquids and Substances Ordinance, 1932 1. These Regulations may be cited as
A. Evaluation of the written program
A. Evaluation of the written program Begin your audit with an evaluation of the written respiratory protection program. In addition to the operating procedures describing respirator selection and use in
WORKPLACE SAFETY AND HEALTH ACT (CHAPTER 354A) WORKPLACE SAFETY AND HEALTH (CONFINED SPACES) REGULATIONS 2009
WORKPLACE SAFETY AND HEALTH ACT (CHAPTER 354A) WORKPLACE SAFETY AND HEALTH (CONFINED SPACES) REGULATIONS 2009 In exercise of the powers conferred by section 65 of the Workplace Safety and Health Act, the
This test shall be carried out on all vehicles equipped with open type traction batteries.
5.4. Determination of hydrogen emissions page 1 RESS-6-15 5.4.1. This test shall be carried out on all vehicles equipped with open type traction batteries. 5.4.2. The test shall be conducted following
API Standard Venting Atmospheric and Low-Pressure Storage Tanks: Nonrefrigerated and Refrigerated
General API Standard 2000 - Venting Atmospheric and Low-Pressure Storage Tanks: Is there any limit for the maximum allowable linear velocity or any other parameter for the roof of a floating roof tank
PSSI 36 General Confined Spaces, Tunnels, Culverts and Similar Spaces
1. SCOPE This document now includes provision for safe access to cable tunnels and culverts previously covered in PSSI 37 which is now withdrawn. The term Confined Space is defined in the Confined Spaces
CODE OF GUIDANCE. For the Storage of Full & Empty LPG Cylinders and Cartridges. Page 1
CODE OF GUIDANCE For the Storage of Full & Empty LPG Cylinders and Cartridges. Page 1 Introduction LP Gas Association (LPGA) Code of Practice No. 7 Storage of Full and Empty LPG Cylinders and Cartridges
MASTER FUME Specialty Gas Fumigant
RESTRICTED USE PESTICIDE (Due to Acute Inhalation Toxicity of Sulfuryl Fluoride) FOR SALE TO AND USE ONLY BY CERTIFIED APPLICATORS OR PERSONS UNDER THEIR DIRECT SUPERVISION AND ONLY FOR THOSE USES COVERED
Installation of Ballast Water Management Systems
(Sept 2015) (Rev.1 May 2016) Installation of Ballast Water Management Systems 1. Application In addition to the requirements contained in BWM Convention (2004), the following requirements are applied to
City of Rolling Hills Equestrian Facility Guidelines
City of Rolling Hills Equestrian Facility Guidelines Drafted by the Stable Ad Hoc Committee STABLE GUIDELINES 1 2 [STABLE GUIDELINES] 2017 INTRODUCTION The Rolling Hills City Council noted a recent trend
BEGINNING THE MEETING
Asbestos This safety talk is designed for discussion leaders to use in preparing safety meetings. Set a specific time and date for your safety meeting. Publicize your meeting so everyone involved will
CONFINED SPACE WRITTEN PROGRAM
CONFINED SPACE WRITTEN PROGRAM Maple River Public Schools ISD#2135 Confined Space Entry Plan (Permit Required) Maple River Public School Plan last updated: October, 2014 Authority and Scope Regulation:
Title: Abrasive Blasting Effective Date: 11/17/2014 Control Number: THG_0034 Revision Number: 1 Date: 10/22/2015 Annual Review Completed: 5/13/2015
Title: Abrasive Blasting Effective Date: 11/17/2014 Control Number: THG_0034 Revision Number: 1 Date: 10/22/2015 Annual Review Completed: 5/13/2015 Abrasive Blasting CONTENTS I. PURPOSE II. SCOPE III.
Confined Space Entry Program Guidelines (Human Resources - Health and Safety Department)
Confined Space Entry Program Guidelines (Human Resources - Health and Safety Department) Introduction The Thames Valley District School Board, through the Health and Safety Policy is committed to providing
CFBT LEVEL II COURSE INFORMATION SHEET
CFBT LEVEL II COURSE INFORMATION SHEET Course Description Compartment Fire Behavior Training (CFBT) Level II builds on the foundational knowledge and skills developed in CFBT Level I. Critical learning
U.S. CONSUMER PRODUCT SAFETY COMMISSION Office of Compliance
U.S. CONSUMER PRODUCT SAFETY COMMISSION Office of Compliance Requirements for Bicycle Helmets 16 C.F.R. Part 1203 What is the purpose of the requirements for bicycle helmets? This regulation sets performance
SMOKE CONTROL USING POSITIVE PRESSURE FANS
SMOKE CONTROL USING POSITIVE PRESSURE FANS 1. INTRODUCTION 1.1 This circular outlines operational guidelines for smoke and CO control using positive pressure fans (PPF) at fires and emergencies. Fans can
Class 2 Gases Learning Tool
Class 2 Gases Learning Tool This work has been produced by DGL (Aust) Pty Ltd This Learner s Guide is about the skills and knowledge required to store and warehouse Class 2 Gases at DGL (Aust) facilities.
Post Harvest Diphenylamine Anti-scald Agent for Post-Harvest Treatment of Apples by Thermal Fogging
2010-0412 2012-06-29 ecofog-100 Post Harvest Diphenylamine Anti-scald Agent for Post-Harvest Treatment of Apples by Thermal Fogging COMMERCIAL PLANT GROWTH REGULATOR ecofog-100 is recommended for reducing
Incorrect Relief Valve Material Causes Release
Incorrect Relief Valve Material Causes Release Lessons Learned Volume 04 Issue 18 2004 USW Purpose Incorrect Relief Valve Material Causes Release To conduct a small group lessons learned activity to share
AQIS METHYL BROMIDE FUMIGATION STANDARD. Version 1.5 July 2010
AQIS METHYL BROMIDE FUMIGATION STANDARD Version 1.5 July 2010 CONTENTS Fumigant considerations risk assessment, commodity, dosage, temperature...5 1.1 Risk assessment...5 1.2 Commodity (Non perishable)...5
CONFINED SPACE AWARENESS
Document Number: HSE09-001 June 1, 2013 AWARENESS Author: A Holland MAPP Construction - Corporate 344 Third Street Baton Rouge, LA 70801 (225) 757-0111 MAPP Construction - Houston 1511 Katy Freeway, Suite
WHAT ARE THE SPECIFICATIONS FOR THE ARGON GAS OPTION USED IN JOULE THOMSON REFRIGERATORS?
MMR Technologies, Inc. WHAT ARE THE SPECIFICATIONS FOR THE ARGON GAS OPTION USED IN JOULE THOMSON REFRIGERATORS? Joule Thomson refrigerators operate using high pressure gas to cool a sample stage with
SAMPLE. Respirable Silica Exposure Control Plan
Respirable Silica Exposure Control Plan This policy applies to all occupational exposures to respirable crystalline silica in construction work, except where employee exposure will remain below 25 micrograms
Instrument Craftsman Receives Caustic Burn to Ear
Instrument Craftsman Receives Caustic Burn to Ear Lessons Learned Volume 03 Issue 38 2004 USW Instrument Craftsman Receives Caustic Burn to Ear Purpose To conduct a small group lessons learned activity
Key Technology, Inc. Confined Space Entry Program. July, 2017
Key Technology, Inc. Confined Space Entry Program July, 2017 Page 1 of 11 Key Technology, Inc. CONFINED SPACE ENTRY PROGRAM OVERVIEW Purpose: The purpose of this program is to ensure the protection of
ANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS
Annex 3, page 2 ANNEX AMENDMENTS TO THE INTERNATIONAL CODE FOR FIRE SAFETY SYSTEMS (FSS CODE) CHAPTER 15 INERT GAS SYSTEMS The text of existing chapter 15 is replaced by the following: "1 Application This