Operating manual SV120
|
|
- Luke Collin Page
- 5 years ago
- Views:
Transcription
1 Operating manual SV120 C _EN 11/2009 Rev. 0
2
3 Foreword Before setting up and commissioning the sliding vane compressor SV120, please read through this operating manual carefully. The operating manual contains important instructions which must be followed strictly if trouble-free operation and a long service life are to be ensured. Scope of application of the operating manual This operating manual only contains instructions for the sliding vane compressor SV120 of type D and H in combination with the respective accessory (compressor kit). This operating manual is valid only for operation of a compressor system, which was completed with ancillaries delivered by GHH RAND. Target group Use of the operating manual is exclusively restricted to qualified specialists. Instructions and safety instructions The following instructions and safety instructions are used in the operating manual to warn of dangers which could lead to operating errors, injuries and damage to property: Safety information Explanation of safety signal words DANGER Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. Caution Indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury or property damage. Indicates information or a company policy that relates directly or indirectly to the safety of personnel or protection of property.
4
5 Table of Contents 1 General Application Manufactuer's address Identification Information for enquiries and orders Service locations Technical data Tightening torques Safety General Authorized personnel, training and qualification Safety-conscious work Safety instructions for the owner / operator Unauthorized conversions and spare parts Incorrect operating methods Disposal / decommissioning Operation Safety during operation Initial commissioning Switching on Monitoring operation Switching off Storage Maintenance / repair Safety Tightening torques Maintenance intervals Maintenance work Faults, causes and instructions for troubleshooting... 16
6
7 1 General 1.1 Application GHH RAND built and supplied the sliding vane compressor SV120 as a component of the SV120D (Direct Drive) or SV120H (Hydraulic Drive), compressor kits for installation on tanker trucks as a ready for connection unit. The compressors are mounted on tanker trucks and, because of the oil free compression of atmospheric air and the power-weight ratio, are used for the pneumatically assisted discharge of liquids, in cases where the use of pumps is difficult or impossible due to the problems caused by direct contact between liquid and pump. The products made and supplied by GHH RAND are designed for commercial vehicles applications for on road operation only. For all other uses, it is necessary to consult the manufacturer. 1.2 Manufacturer s address GHH RAND Schraubenkompressoren GmbH Max-Planck-Ring Oberhausen Germany 1.3 Identification The machine number is to be taken from the accompanying documents. In order to always have the number ready available, we recommend that you enter it into the following blank space. Mach. No. 1.4 Information for inquiries and orders If you have inquiries or orders for spare parts and accessories, please provide details of the exact type designation and the machine number of the compressor for which the spare part or accessory is intended. To ensure safety, use original spare parts and accessories authorized by the manufacturer. The use of spare parts and accessories which are not original or not authorized may exempt the manufacturer of any liability for the consequences. 1.5 Service locations For addresses of service locations, please see the last inside page of this operating manual or the internet page: C _EN 11/2009 Rev. 0 1
8 1.6 Technical data (ISO units) Dimensions & weights SV120 D H Length (approx.) mm Width (approx.) mm Height (approx.) mm Weight (approx.) kg 37 39* *without hydraulic motor (option) Speed range SV120 D/H min. min max. min Maximum operating pressure SV120 max. 2.5 bar Performance data Performance data Unit SV120D/H Speed compressor min Discharge pressure bar(g) 1.5 Flow rate m 3 /h Power at coupling kw Discharge temperature C Suction temperature, max. C Discharge pressure bar(g) 2.0 Flow rate m 3 /h Power at coupling kw Discharge temperature C Suction temperature, max. C Discharge pressure bar(g) 2.5 Flow rate m 3 /h Power at coupling kw Discharge temperature C Suction temperature, max. C Discharge temperature at max. suction temperature C All specifications for: Medium pumped: atmospheric air Suction pressure: 1 bar (abs.) Suction temperature: 20 C Technical data without loss of suction or pressure 2 C _EN 11/2009 Rev. 0
9 1.6 Technical data (Imperial units) Dimensions & weights SV120 D H Length (approx.) inch Width (approx.) inch Height (approx.) inch Weight (approx.) lb 82 86* * weight without hydraulic motor (option) Speed range SV120 D/H min. rpm 1000 max. rpm 1800 Maximum operating pressure SV120 max. 36 psig Performance data Performance data Unit SV120D/H Speed compressor rpm Discharge pressure psig 15.0 Flow rate cfm Power at coupling hp Discharge temperature F Suction temperature, max. F Discharge pressure psig 25.0 Flow rate cfm Power at coupling hp Discharge temperature F Suction temperature, max. F Discharge pressure psig 36.0 Flow rate cfm Power at coupling hp Discharge temperature F Suction temperature, max. F Discharge temperature at max. suction temperature F All specifications for: Medium pumped: atmospheric air Suction pressure: psia Suction temperature: 68 F Technical data without loss of suction or pressure C _EN 11/2009 Rev. 0 3
10 1.7 Tightening torques Description Fastening screws (M ) compressor to fastening plate/foot Fastening screws (M ) compressor fastening plate to mounting bracket Screws (M ) suction/discharge port to compressor Screws (M6) shear bolts to overload coupling (optional) Tightening torque 58 Nm / 42.8 lbf ft 82 Nm / 60.5 lbf ft 50 Nm/ 36.9 lbf ft 10 Nm / 7.4 lbf ft 4 C _EN 11/2009 Rev. 0
11 2 Safety 2.1 General This operating manual contains basic instructions to be followed during operation and maintenance / repair. This operating manual must be read by the responsible technical staff / operator prior to commissioning. This operating manual must always be available at the place of use of the compressor / accessory. 2.2 Authorized personnel, training and qualification Work performed on the compressor and the accessory, such as operation and maintenance / repair, must only be carried out by persons with the appropriate authorization, training and qualification, who are familiar with the valid safety regulations. Repair or retrofitting work may only be performed by authorized personnel; such persons are always available from the service locations or GHH RAND. 2.3 Safety-conscious work The important safety-related regulations for installation, operation and maintenance / repair of air compressors are contained in the following publications: The regulations of the professional associations, in particular: Standards, in particular: ISO Safety of machinery EN Compressors and vacuum pumps, safety requirements The following regulations and guidelines are to be observed in addition: Product-related safety data sheets in particular with regard to explosion protection, handling and storage Technical rules for hazardous materials (TRGS) Technical rules for operational safety (TRBS) The most recent valid issues of these regulations apply. Any special internal legal rules and regulations, particularly safety regulations, which apply due to local conditions, regions or environments must also be observed. If there are conflicting regulations, the stricter regulations are to be applied. You must also observe any national regulations in the respective country of use. C _EN 11/2009 Rev. 0 5
12 2.4 Safety instructions for the owner / operator The owner / operator is responsible for ensuring that the sliding vane compressor / the compressor kit is in safe operational condition. Damaged or faulty parts must be replaced immediately. Keep safety / warning labels in a readable condition; replace, if necessary. Do not operate the unit in an area where flammable or potentially explosive gases are present, as they will be sucked in when operating the compressor. Always wear hearing protection when operating this unit, due to the high sound level of the compressor during operation. The supplied safety valve must be installed during installation of the compressor. Its purpose is to protect the compressor against exceeding the permissible operating pressure. Make sure that the tank / pressure vessel is equipped with a functional safety valve set to the permissible operating pressure. 2.5 Unauthorized conversions and spare parts Conversion and modifications to the sliding vane compressor / compressor kit are not permitted. If the seal is broken, the warranty is rendered null and void. To ensure safety, use original spare parts and accessories authorized by the manufacturer. The use of nonoriginal or non-authorized spare parts and accessories may exempt the manufacturer of any liability for the consequences. 2.6 Incorrect operating methods The sliding vane compressor and the compressor kit must be operated under the conditions stated in chapter 1.6 Technical data unless you have approval from GHH RAND stating otherwise. Operating the sliding vane compressor / the compressor kit under improper conditions may cause serious injury and considerable material damage. 2.7 Disposal / decommissioning Dispose of operating materials and parts after use in a proper and environmentally friendly manner. 6 C _EN 11/2009 Rev. 0
13 3 Operation 3.1 Safety during operation Wear protective gloves! Risk of burns from hot machine parts. See also the safety instructions in Chapter 2 Safety. Do not operate the compressor in excess of the maximum discharge pressure of 2.5 bar (36 psig). If the maximum discharge pressure is exceeded, switch off the compressor immediately. In case of unusal operating noises, immediately switch off the compressor. For possible causes and actions to be taken, see Chapter 5 Faults, Causes and Instructions for Troubleshooting. 3.2 Initial commissioning Initial commissioning of the compressor is usually carried out by the system manufacturer. It includes checking the direction of rotation as well as a test run. For further information on the above points, please see the Installation and Service Instructions SV120. Leveling Park the vehicle in as level a position as possible. Maximum permitted inclination in machine direction when operating the sliding vane compressor: +/ Switching on Switch on power take-off (PTO). Only start the compressor when completely depressurized. Never put it into operation if there is any back pressure. When the compressor drive shaft is not encased, make sure that no persons are near the drive shaft prior to switching on the power take-off. C _EN 11/2009 Rev. 0 7
14 3.4 Monitoring operation 3.5 Switching off 3.6 Long-term storage Maintenance indicator Switch off power take-off (PTO). Do not shut down the compressor when there is back pressure! If there is any back pressure, take appropriate measures for relieving pressure before switching off. Before the machine is installed, or if it has been removed from the driveline, and where it will be shut down for an extended period of time, then it should be stored in a clean and dry place. It is recommended to shrink wrap the compressor with water proof film with a desiccant pack inside the packaging. Where the compressor is mounted on a vehicle located outside, then the compressor should be operated for 15 minutes each week (twice per week in cold or damp conditions). The suction pressure in the suction pipe (1) to the compressor is displayed on the maintenance indicator (2). If a suction pressure of 50 mbar (0.94 psi) is reached (yellow plate (3) reaches red area Service ), the permissible suction pressure has been exceeded. In this case, clean the filter cartridge in the compressor s suction filter or, if the level of clogging is too high, replace the filter cartridge (see Chapter 4 Maintenance / repair ). Caution The inside of the compressor must by no means come into contact with an oily preservative as it may seriously damage the vanes when re-starting the compressor. 8 C _EN 11/2009 Rev. 0
15 4 Maintenance / repair 4.1 Safety All checks and maintenance work must only be performed with the compressor switched off and depressurized. Wear protective gloves! Risk of burns from hot machine parts. Turn off the engine and remove the key from the truck s ignition before beginning any maintenance operation. See also the safety instructions in Chapter 2 Safety. When cleaning a tanker truck with a steam jet device, there is the possibility that water will seep into the inside of the compressor. In order to prevent corrosion, it is necessary to run the compressor briefly after cleaning (approx. 15 min.). 4.2 Tightening torques For more information about the required tightening torques, see Chapter 1.7 Tightening torques. 4.3 Maintenance intervals All of the maintenance and repair work listed on this page is described in detail in the following Chapter 4.4. Daily: Check the maintenance indicator and clean the suction filter, if necessary, or replace if it is extremely dirty. Weekly: Clean the compressor (cooling fins and covers). Run the compressor for approximately 15 minutes at least once a week. Check the suction filter and pipes for leaks. Monthly: Check the safety valve and the nonreturn valve for correct functioning. Check the suction and discharge pipes for leaks. Quarterly: Check the fastening screws of the compressor to the bracket. Clean the suction filter housing and filter cartridge, replace the filter cartridge if necessary. Annually: Check the piping and piping fixtures for corrosion and replace if necessary. C _EN 11/2009 Rev. 0 9
16 Every 2 years / 1000 operating hours: Check the wear of the blades; Service compressor if necessary; refer to Installation and Service Instruction SV120. To ensure optimal operational safety and performance, it is recommended to service the compressor after every 1000 hours of operation (replacement of bearings and slide gate valve). 4.4 Maintenance work Checking the maintenance indicator The design of the maintenance indicator allows reading of the suction pressure when the compressor is switched off. 4 3 Check the displayed value / position of the yellow indicator piston (1) of the maintenance indicator (2) If the yellow piston reaches the red area Service (4), the max. permissible suction pressure of 50 mbar (0.94 psi) is exceeded. In this case: Clean the suction filter - see Chapter Push the button (3) in order to reset the maintenance indicator to Zero Cleaning the compressor Keep all the compressor connection ports shut. Ingress of foreign particles into the compressor may result in damage of the compressor. Prior to cleaning the compressor with a steam jet device / high pressure cleaner, let it cool down. Keep a minimum distance of 0.5 m (1.6 ft) when using a high pressure cleaner. Do not use any highly alkaline cleaners (bases) risk of corrosion! Rinse the components with pure water after using a cleaner. Remove any debris from the cooling fins of the compressor and the ventilation grid of the covers. In order to prevent corrosion, run the compressor briefly after cleaning (approximately 15 minutes). 10 C _EN 11/2009 Rev. 0
17 4.4.3 Checking the suction filter and piping for leaks Checking the safety and non-return valve For North American safety valves, release the valve by pulling on the ring on the end of the valve to ensure the seat opens. Caution Don t check while the compressor is in operation. 3 Visually check the suction filter housing (1), rubber elbow (2) with maintenance indicator, pipe (3) as well as pipe connections and flanged connections on the compressor for leaks. Unscrew the knurled nut (1) of the safety valve (2). In the loosened state, the valve seat (3) must open. Replace safety valve if needed. When installing a new safety valve, pay due attention to the indications provided by the manufacturer. Tighten the knurled nut (1) of the safety valve (2). C _EN 11/2009 Rev. 0 11
18 1 2 Combined safety and non-return valve: 1 Reach into the inlet port (2) with a finger. Inside the housing, push upwards the valve plate above the bore of the safety valve (4) and check that it is working smoothly. Replace the combined safety and non-return valve as necessary. 3 Remove the non-return valve (1). On the intake side of the non-return valve, push down the valve plate (2) on the shaft (see arrow) and check that it is working smoothly. If necessary, replace the non-return valve. Pay attention to the proper installation position of the non-return valve during assembly. The direction of flow of the non-return valve is indicated by an arrow (3) on the housing. 4 Loosen the screw connections on the flanges of the combined safety and non-return valve (1) and take off the valve together with the flange seals. Check the safety valve (3) as described before. Replace the safety valve, if needed. 2 3 When replacing the combined safety and non-return valve, the faultless safety valve can be screwed off and installed onto the new non-return valve. Install the safety / non-return valve with new seals onto the flanges of the discharge pipe. Pay attention to the proper installation position of the combined safety and non-return valve during assembly. The direction of flow of the non-return valve is indicated by an arrow on the housing. Always use new gaskets when reinstalling on the flanges of the discharge pipe. 12 C _EN 11/2009 Rev. 0
19 4.4.5 Checking the compressor fastening Cleaning the suction filter Caution Do not clean the air filter cartridge by means of compressed air or liquids. Clean the filter cartridge by lightly beating on it. Replace the filter cartridge if needed. Assembly occurs in reverse order When installing the cover, make sure that the dust separator valve points vertically down. (See the OBEN/TOP mark on the front side of the cover.) Check the four fastening screws (3) of the compressor on the fastening plate; re-tigthen them cross-wise at a torque of 58 Nm (42.8 lbf ft), if necessary. Check screwed connections (2; total 4) of the fastening plate to the mounting bracket; re-tighten nuts cross-wise at 82 Nm (60.5 lbf ft), if necessary; lock the screws on the back when doing so. Check the screwed connections (1; 4 min.) of the mounting bracket to the truck chassis. 5 4 Push down the snap fits (2) on the left and right-hand side of the cover (1) and remove the cover from the air filter housing (4). Pull out the filter cartridge (3). Clean the inside of the filter housing. Press together the dust separator valve (5) on the cover such that the rubber lips open and the dirt collected inside can fall out. C _EN 11/2009 Rev. 0 13
20 4.4.7 Checking the wear of the vanes Loosen the nuts (1) on the discharge port of the compressor and remove them together with the washers (2) from the fastening screws (5). The discharge port is the port at which the direction of rotation arrow (6) points Remove the flange (3) of the discharge pipe from the compressor and put the discharge pipe aside. Remove and discard the gasket and remove the screws (5) from the compressor flange. Make sure that no foreign particles enter the compressor through the open discharge flange. Ingress of foreign particles into the compressor may result in damage of the compressor. Do not reach into the compressor ports with your hands - risk of injury through shearing! 1 A 2 Through the discharge port (2), visually line up the rotor slot (3) and then carefully insert a max. 5 mm (0.2 inches) thick, clean device into the rotor slot (3) and push it forward up to the upper edge of the vane (4). Manually turn the rotor by hand in the indicated direction of rotation to line up the rotor slot (see direction of rotation arrow on the housing), if necessary. Mark the device at the level of the compressor flange and pull it out of the compressor again. Measure the distance A C _EN 11/2009 Rev. 0
21 When the value of A exceeds 105 mm (4.13 inches), it is recommended to replace the vanes or conduct maintenance due to the wear of the vanes. See Installation and Service Manual. When the value of A is below or equal 105 mm (4.13 inches), the length of the vanes is usually sufficient until the next maintenance date; in this case: Screw back on the discharge pipe with new gasket onto the compressor. Always insert the screw heads into the slot on the compressor flange. Otherwise, the compressor housing may be damaged depending on the length of the screw. Do not use electro-conductive gaskets due to the risk of corrosion! Further operation of the compressor with the vanes worn may result in damage of the rotor and the compressor housing; this in turn results in an excessive wear / shorter life of new vanes Replacing the shear bolts of the overload clutch Prior to fitting in new shear bolts, find the reason why they sheared off, see chapter 5 Faults, causes and instructions for troubleshooting. Check free rotatability of the compressor by turning the drive shaft. The bolts (1) of the overload clutch (3, optional) can shear off if the torque is too high. They have to be replaced as described below: Unscrew the hexagon socket screws (2) and remove the shear bolts (1) Fit in new shear bolts (marked BG [blue-green]) and fix them with the hexagon socket screws M6 (2) (tightening torque = 10 Nm (7.4 lbf ft)). C _EN 11/2009 Rev. 0 15
22 5 Faults, causes and instructions for troubleshooting If in doubt, turn off the compressor! Fault Possible cause Remedy Chapter Volume air flow not sufficient Discharge pressure too high Discharge temperature too high Suction pressure exceeds 50 mbar (0.94 psi) Too loud or unusual running noise Compressor does not work Drive speed too low Increase drive speed to the maximum permitted speed 1.6 Suction filter soiled/clogged Clean or replace filter cartridge as necessary / Suction hose kinked Check suction hose; re-install as necessary Nominal diameter of the discharge pipe Install new pipes with a larger nominal diameter too small Non-return valve faulty Check the non-return valve Safety valve does not open Check the safety valve Drive speed too high Reduce the drive speed to the maximum permitted speed 1.6 / 1.7 Suction filter soiled / clogged Clean or replace the filter cartridge as necessary / Cooling fans compressor housing / Clean the compressor fan covers dirty / clogged Discharge pressure too high Check the safety valve Ambient temperature too high Observe permitted suction temperature 1.6 Compressor vanes worn / stuck in rotor slots Repair the compressor see Installation / Service Manual Suction filter dirty / clogged Clean or replace the filter cartridge as necessary / Suction hose kinked Check the suction hose; re-insall as necessary Drive speed too low Increase drive speed up to the minimum permitted speed Vanes worn or damaged / surface of compressor bore damaged Shear bolts sheared off Repair the compressor see Installation / Service Manual Replace the shear bolts; identify and rectify reason for excessive torque 16 C _EN 11/2009 Rev. 0
23 Fault Possible cause Remedy Chapter Shear bolts sheared off repeatedly Compressor switched on/off under Relieve pressure 3.3 / 3.5 back pressure For manual transmissions: Engage clutch at slower rate clutch engagement too fast For automatic transmissions: Have parameters changed by service center coupling times too short Compressor defective Replace compressor C _EN 11/2009 Rev. 0 17
24 Notes 18 C _EN 11/2009 Rev. 0
25 Service GHH RAND Schraubenkompressoren GmbH Max-Planck-Ring 27 D Oberhausen, Germany Service Hotline Tel. (+49) 208 / Service Tel. (+49) 208 / Spare Parts Tel. (+49) 208 / Fax (+49) 208 / Internet info_ghh-rand@irco.com Printed in Germany The technical details are subject to change and may vary from the information and illustrations in the operating manual. This document must not be reprinted, translated or reproduced, either in part or in full, without prior written permission.
26 GHH RAND Schraubenkompressoren GmbH Max-Planck-Ring 27 D Oberhausen Service Hotline Tel. (+49) 208 / Fax (+49) 208 / Subject to revision without notice Printed in the Federal Republic of Germany 11/2009 EN As a contribution to environmental protection, this paper has been produced from 100% chlorine-free bleached pulp.
Mounting and Operating Instructions EB 2558 EN. Self-operated Pressure Regulators. Type Pressure Build-up Regulator
Self-operated Pressure Regulators Type 2357-31 Pressure Build-up Regulator with safety function and integrated excess pressure valve Type 2357-31 with non-return unit at port C Ports A and B with soldering
More information200 PSI COMPRESSORS - MODEL NUMBERS
200 PSI COMPRESSORS - MODEL NUMBERS 380C AIR COMPRESSOR KIT PART NO. 38033 480C AIR COMPRESSOR KIT PART NO. 48043 380C 480C IMPORTANT: It is essential that you and any other operator of this product read
More information100C Air Compressor Kit
10010 100C Air Compressor (standard mounting bracket, CE Spec) 10014 100C Air Compressor (no leader hose or check valve, CE Spec) 10016 100C Air Compressor (with Omega Bracket, CE Spec) IMPORTANT: It is
More information444C DUAL PERFORMANCE VALUE PACK
(Chrome) PART NO. 44432 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL
More informationSC6H OIL-LESS AIR COMPRESSOR
SC6H OIL-LESS AIR COMPRESSOR OWNER S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE. MAIN COMPONENTS 1. ON/OFF switch 2. Outlet valve 3. Regulating valve
More information97C COMPRESSOR KIT 12V PART NO C COMPRESSOR KIT 24V PART NO C COMPRESSOR KIT PART NO
97C COMPRESSOR KIT 12V PART NO. 00097 97C COMPRESSOR KIT 24V PART NO. 02497 98C COMPRESSOR KIT PART NO. 00098 97C 98C IMPORTANT: It is essential that you and any other operator of this product read and
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock: - Do not disassemble. Do not attempt repairs or modifications. Refer to qualified service agencies for all service and repairs.
More information420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO
420C AIR COMPRESSOR KIT PART NO. 42042 460C AIR COMPRESSOR KIT PART NO. 46043 420C 460C IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this
More information3/8" Dr. Air Butterfly Impact Wrench
8192106 3/8" Dr. Air Butterfly Impact Wrench Owner s Manual Read and understand all instructions before use. Retain this manual for future reference. Specifications Construction: Polished aluminum and
More information24L OIL FREE AIR COMPRESSOR MODEL NO: TIGER 7/250 PART NO: OPERATION & MAINTENANCE INSTRUCTIONS LS10/13
24L OIL FREE AIR COMPRESSOR MODEL NO: TIGER 7/250 PART NO: 2244030 OPERATION & MAINTENANCE INSTRUCTIONS LS10/13 INTRODUCTION Thank you for purchasing this product. Before attempting to use this product,
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More information400H HARDMOUNT AIR COMPRESSOR KIT PART NO H HARDMOUNT AIR COMPRESSOR KIT PART NO
400H HARDMOUNT AIR COMPRESSOR KIT PART NO. 40042 450H HARDMOUNT AIR COMPRESSOR KIT PART NO. 45042 400H 450H IMPORTANT: It is essential that you and any other operator of this product read and understand
More informationPneumatic proportional controller Types M Types FM Function tested for use of the float in Ex-zone 0
Operating Manual LTIA5E Pneumatic proportional controller Types M Types FM Function tested for use of the float in Ex-zone 0 Contents 1. Safety Instructions 2. Conformity to standards 3. Technical data
More informationMODEL NUMBER: PSI AIR SOURCE KIT 200 PSI Compressor on 2.0 Gallon 200 PSI Air Tank
IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock or Electrocution: MODEL NUMBER: 20008 200 PSI AIR SOURCE KIT 200 PSI Compressor on 2.0 Gallon 200 PSI Air Tank IMPORTANT: It is
More informationCode AWC20HP Air Compressor
Code 951816 AWC20HP Air Compressor Index of Contents Index of Contents 02 Declaration of Conformity 02 What s Included 03 Safety Precautions 03 Specifications (AWC20HP Air Compressor) 04 Assembly Instructions
More informationDP Spare parts list. Demolition pulverizer. DP 2800 s/n DEQ Construction Tools GmbH No
DP 2800 Spare parts list Demolition pulverizer DP 2800 s/n DEQ139266-2018 Construction Tools GmbH No. 3390719501 2018-01-01 General information This spare parts list applies to the following: Part number
More informationType 2000 INOX. Quickstart. English Deutsch Français. 2/2-way angle seat valve 2/2-Wege Schrägsitzventil Vanne à siège incliné 2/2 voies
Type 2000 INOX 2/2-way angle seat valve 2/2-Wege Schrägsitzventil Vanne à siège incliné 2/2 voies Quickstart English Deutsch Français Contents 1 QUICKSTART... 2 2 CONTACT ADDRESS... 2 3 INTENDED USE...
More informationRARS5000 AIR BODY SAW OWNER S OPERATING MANUAL
RARS5000 AIR BODY SAW OWNER S OPERATING MANUAL DESCRIPTION 1. No mar 2. No mar tip 3. Housing grip 4. Trigger 5. Air inlet 6. Air inlet plug 7. Plastic board Important! It is essential that you read the
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More information400C & 450C DUAL PERFORMANCE VALUE PACKS
(Chrome) PART NO. 40013 (Silver) PART NO. 45012 (Chrome) PART NO. 45013 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before
More informationDeclaration of Conformity as per Directive 97/23/EC
Declaration of Conformity as per Directive 97/23/EC The manufacturer declares that:, 47906 Kempen, Germany Multi-way diverting valves Series 29a and Series 29b, with packing with lever 1. The valves are
More informationVERTICAL AIR COMPRESSORS
VERTICAL AIR COMPRESSORS MODEL NO: VE11C150, VE15C150, VE18C150 PART NO: 2226005, 2226000, 2226015 OPERATION & MAINTENANCE INSTRUCTIONS LS0615 INTRODUCTION Thank you for purchasing this CLARKE Vertical
More informationIMPACT WRENCH MODEL NO: CAT78 OPERATING & MAINTENANCE INSTRUCTIONS PART NO: GC0813
IMPACT WRENCH MODEL NO: CAT78 PART NO: 3110790 OPERATING & MAINTENANCE INSTRUCTIONS GC0813 INTRODUCTION Thank you for purchasing this CLARKE Impact Wrench. Before attempting to use this product, please
More informationVERTICAL AIR COMPRESSORS
VERTICAL AIR COMPRESSORS MODEL NO: VE15C150, VE18C150, VE25C150 PART NO: 2226010, 2226020, 2226025 OPERATION & MAINTENANCE INSTRUCTIONS LS0715 INTRODUCTION Thank you for purchasing this CLARKE Vertical
More information200 PSI FAST-FILL AIR SOURCE KIT
200 PSI FAST-FILL AIR SOURCE KIT 55% Duty Compressor on 2.0 Gallon Air Tank PART NO. 20007 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of
More informationMODEL NUMBER: M20005 AIR SOURCE KIT. 30% Duty Compressor on. 2.0 Gallon Air Tank SAVE THIS MANUAL FOR FUTURE REFERENCE
MODEL NUMBER: M20005 AIR SOURCE KIT 30% Duty Compressor on 2.0 Gallon Air Tank SAVE THIS MANUAL FOR FUTURE REFERENCE USER MANUAL IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock
More informationOPERATION & MAINTENANCE INSTRUCTIONS
1 /2 REVERSIBLE AIR DRILL MODEL NO: CAT123 PART NO: 3110879 OPERATION & MAINTENANCE INSTRUCTIONS GC1110 INTRODUCTION Thank you for purchasing this CLARKE product. Before attempting to use this product,
More informationSPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.
2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or
More information200 PSI HIGH-FLOW AIR SOURCE KIT
200 PSI HIGH-FLOW AIR SOURCE KIT 50% Duty Compressor on 2.0 Gallon Air Tank PART NO. 20008 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of
More information100L AIR COMPRESSOR MODEL NO: TIGER 16/1010 PART NO: OPERATION & MAINTENANCE INSTRUCTIONS LS01/13
100L AIR COMPRESSOR MODEL NO: TIGER 16/1010 PART NO: 2244025 OPERATION & MAINTENANCE INSTRUCTIONS LS01/13 INTRODUCTION Thank you for purchasing this product. Before attempting to use this product, please
More informationSiphon vessel / Priming aid
Manufacturer: sera GmbH sera-straße 1 34376 Immenhausen Germany Tel.: +49 5673 999-00 Fax: +49 5673 999-01 info@sera-web.com Keep the operating manual for future use! Record the exact type and serial number
More informationMounting and Operating Instructions EB EN. Type Supply Pressure Regulator. with increased air capacity
Type 4708-45 Supply Pressure Regulator with increased air capacity Translation of original instructions Mounting and Operating Instructions EB 8546-1 EN Edition March 2016 Note on these mounting and operating
More informationBudget Range Operators Handbook
Budget Range Operators Handbook BAMBI AIR COMPRESSORS LTD 152 Thimble Mill Lane Heartlands Birmingham B7 5HT United Kingdom Tel: 0121 322 2299 Fax: 0121 322 2297 Email: sales@bambi-air.co.uk www.bambi-air.co.uk
More information30T A/Manual Hydraulic Shop Press
30T A/Manual Hydraulic Shop Press Operation Manual 1 1. Important Information 1.1 Safety Information 1.1.1 Hazard Symbols Used in the Manuals This manual includes the hazard symbols defined below when
More informationCUT OFF TOOL MODEL: CAT113
CUT OFF TOOL MODEL: CAT113 Part No: 3120135 ASSEMBLY & INSTRUCTION MANUAL LS0309 INTRODUCTION Thank you for purchasing this CLARKE product Before attempting to use the product, it is essential that you
More informationMODEL NUMBER: AS18-2 USER GUIDE
Compressor MODEL NUMBER: AS18-2 USER GUIDE WEBSITE: EMAIL: www.airbrushheaven.co.uk enquiries@airbrushheaven.co.uk 1 YEAR WARRANTY Contents 1. Welcome Section 2. General Information & Safety Instructions
More informationRS(H)10,15 USER MANUAL. Read the complete manual before installing and using the regulator.
RS(H)10,15 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to
More informationRight-Angle Tube Roller Model
SPECIFICATIONS Model no. Free Speed (RPM) Throttle Rotation Max. Torque Ft-Lb Air Pressure psi Air Inlet Hose Air Flow @Free Speed Spindle Weight 909-1700 95 Lever type Reversible 240 90 1/2 NPT 1/2 I.D.
More informationInstruction manual. for. high purity gas pigtails 200 bar / 300 bar
Instruction manual for high purity gas pigtails 200 bar / 300 bar Contents Contents... 2 1. Preface... 3 1.1 Overview... 3 1.2 General... 3 1.3 Intended use... 4 1.4 Personnel requirements... 4 2. For
More informationMAINTENANCE AND OPERATING MANUAL
MAINTENANCE AND OPERATING MANUAL Cyclone condensate separator Type ASA EN EN Maintenance and operating manual Purpose and appropriate use Dear Customer, thank you for choosing our product. In order to
More information24L AIR COMPRESSOR MODEL NO: TIGER 11/250 PART NO: OPERATION & MAINTENANCE INSTRUCTIONS LS01/13
24L AIR COMPRESSOR MODEL NO: TIGER 11/250 PART NO: 2244010 OPERATION & MAINTENANCE INSTRUCTIONS LS01/13 INTRODUCTION Thank you for purchasing this product. Before attempting to use this product, please
More information42045 Heavy Duty ADA Base Model Kit: 85/105 PSI (ADA Compressor Only) Heavy Duty ADA Base Model Kit: 110/145 PSI (ADA Compressor Only)
42045 Heavy Duty ADA Base Model Kit: 85/105 PSI (ADA Compressor Only) 42047 Heavy Duty ADA Base Model Kit: 110/145 PSI (ADA Compressor Only) 45052 Constant Duty ADA Base Model Kit: 85/105 PSI (ADA Compressor
More informationINSTRUCTION MANUAL MST AFTERCOOLER SYSTEM MODEL
INSTRUCTION MANUAL MST AFTERCOOLER SYSTEM MODEL 8059601 To be used with MST Model 8050501 Ambient Air Pump 7/12/05 2 TABLE OF CONTENTS GENERAL INFORMATION... 3 WARNING...4,5 UNPACKING AND AFTERCOOLER ASSEMBLY
More informationPressure maintenance valve SDV-P / SDV-P-E
Translation of the original manual Pressure maintenance valve SDV-P / SDV-P-E Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted
More informationINTENDED USE TECHNICAL SPECIFICATIONS
1/2IN. HEAVY-DUTY AIR IMPACT WRENCH OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More information450P- RV AUTOMATIC PORTABLE COMPRESSOR EXTREME SERIES
450P- RV AUTOMATIC PORTABLE COMPRESSOR EXTREME SERIES PART NO. 45053 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing
More information200L BELT DRIVEN AIR COMPRESSOR
200L BELT DRIVEN AIR COMPRESSOR MODEL NO: BOXER 14/200 PART NO: 2245215 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0118 ISS 4 INTRODUCTION Thank you for purchasing this CLARKE 200L Belt
More informationMounting and Operating Instructions EB 3007 EN. Self-operated Pressure Regulators. Differential Pressure Regulators (opening) Type Type 42-25
Self-operated Pressure Regulators Differential Pressure Regulators (opening) Type 42-20 Type 42-25 Type 42-20 Differential Pressure Regulator Type 42-25 Differential Pressure Regulator Mounting and Operating
More informationKTM OM-2 SPLIT BODY FLOATING BALL VALVES INSTALLATION AND MAINTENANCE INSTRUCTIONS
Before installation these instructions must be fully read and understood SECTION 1 - STORAGE 1.1 Preparation and preservation for storage All valves should be properly packed in order to protect the parts
More informationOperating Instructions. Ball valve fitting according to ZB For pressure transmitter VEGABAR 82. Document ID: 50027
Operating Instructions Ball valve fitting according to ZB 2553 For pressure transmitter VEGABAR 82 Document ID: 50027 Contents Contents 1 About this document 1.1 Function... 3 1.2 Target group... 3 1.3
More informationAIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST
AIR COMPRESSOR OPERATING INSTRUCTION AND PARTS LIST OIL-LESS TYPE IMPORTANT: PLEASE READ CAREFULLY BEFORE STARTING OPERATIONS. THE CONTENTS ARE FOR GENERAL INFORMATION OF ALL THE SIMILAR MODELS. Record
More informationAC1810 / AC1810-A TECHNICAL SPECIFICATIONS. Operating Pressure psi ( kgs/cm²) [AC1810] Displacement. Net Weight
Technical Specifications Operating Instructions Maintenance Information Troubleshooting Guide Parts Diagrams AC1810 / AC1810-A THE EVOLUTION OF PERFECTION CAUTION: Before attempting to use or service this
More information450P AUTOMATIC PORTABLE COMPRESSOR EXTREME SERIES
EXTREME SERIES PART NO. 45043 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS
More informationREVERSIBLE AIR DRILL
REVERSIBLE AIR DRILL MODEL NO: CAT87 PART NO: 3110835 OPERATING & MAINTENANCE INSTRUCTIONS GC0613 INTRODUCTION Thank you for purchasing this CLARKE Reversible Air Drill Before attempting to use this product,
More informationPressure relief valve
Pressure relief valve Operating manual Series DHV 712 R Version BA-2016.01.19 EN Print-No. 300 472 TR MA DE Rev001 ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 32602 Vlotho Germany Phone: +49 (0) 5733-799-0
More information24L AIR COMPRESSOR OPERATION & MAINTENANCE INSTRUCTIONS MODEL NO: RANGER 7/240 PART NO: LS0913
24L AIR COMPRESSOR MODEL NO: RANGER 7/240 PART NO: 2242000 OPERATION & MAINTENANCE INSTRUCTIONS LS0913 INTRODUCTION Thank you for purchasing this CLARKE 24L Air Compressor. Please read this manual fully
More informationTwo-stage valve type NE
Two-stage valve type NE Product documentation Operating pressure pmax: Flow rate Qmax: 700 bar (High pressure) 80 bar (Low pressure) 25 lpm (High pressure) 180 lpm (Low pressure) D 7161 03-2017-1.0 by
More informationOperating and maintenance manual Filter and reducing station Series / 1.0
Operating and maintenance manual Filter and reducing station Series 961 04.2017 / 1.0 Original instructions ARCA Regler GmbH. All rights reserved. Cover picture background: Freepik.com ARCA Regler GmbH
More informationOPERATING & MAINTENANCE INSTRUCTIONS
3/8 BUTTERFLY IMPACT WRENCH MODEL NO: CAT64 PART NO: 3110720 OPERATING & MAINTENANCE INSTRUCTIONS GC0414 INTRODUCTION Thank you for purchasing this CLARKE Impact Wrench. The CAT64 is a compact and lightweight
More informationModel PSI Compressor with 3-Gallon Air Tank 12VDC
Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing
More informationFILTER REGULATORS MODEL NO: CAT155 & CAT156 FITTING & MAINTENANCE INSTRUCTIONS PART NO: & ORIGINAL INSTRUCTIONS
FILTER REGULATORS MODEL NO: CAT155 & CAT156 PART NO: 3120169 & 3120170 FITTING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0117 INTRODUCTION Thank you for purchasing this CLARKE Filter/Regulator.
More informationPressure relief valve
Pressure relief valve Operating manual Series DHV 718 Version BA-2016.01.11 EN Print-No. 300 524 TR MA DE Rev001 ASV Stübbe GmbH & Co. KG Hollwieser Straße 5 32602 Vlotho Germany Phone: +49 (0) 5733-799-0
More informationAIR RATCHET WRENCH MODEL NO: CAT21B & CAT90 OPERATING & MAINTENANCE INSTRUCTIONS PART NO: & GC05/14
AIR RATCHET WRENCH MODEL NO: CAT21B & CAT90 PART NO: 3110400 & 3110846 OPERATING & MAINTENANCE INSTRUCTIONS GC05/14 INTRODUCTION Thank you for purchasing this CLARKE Air-Powered Ratchet Wrench. Before
More informationPRS(TC)4,8 USER MANUAL. Read the complete manual before installing and using the regulator.
PRS(TC)4,8 USER MANUAL Read the complete manual before installing and using the regulator. WARNING INCORRECT OR IMPROPER USE OF THIS PRODUCT CAN CAUSE SERIOUS PERSONAL INJURY AND PROPERTY DAMAGE. Due to
More informationMANUAL SEALLESS STEEL STRAPPING TOOL MODEL A
OPERATION MANUAL / SPARE PARTS LIST MANUAL SEALLESS STEEL STRAPPING TOOL MODEL A337.0001 13.1912.01 13191201.en/MAS/ 10.02 INDEX PAGE 1 SAFETY INSTRUCTIONS 2 2 WARRANTY CONDITIONS AND LIABILITY 4 3 APPROPRIATE
More informationBall valve. Operating instructions for series. Version BA Print-No TR MA DE Rev001
Ball valve Operating instructions for series Version BA-2016.02.05 Print-No. 300 587 TR MA DE Rev001 We reserve the right to make technical changes. Read carefully before use. Save for future use. ASV
More informationAIR COMPRESSOR OPERATION & MAINTENANCE INSTRUCTIONS MODEL NO: CHAMP 3 PART NO: LS0115
AIR COMPRESSOR MODEL NO: CHAMP 3 PART NO: 2225222 OPERATION & MAINTENANCE INSTRUCTIONS LS0115 INTRODUCTION Thank you for purchasing this CLARKE Air Compressor. Please read this manual fully before use
More informationInnovative Vacuum for Automation. Operating Instructions Dust Filter STF P / STF-D P.
Innovative Vacuum for Automation EN Operating Instructions Dust Filter STF P / STF-D P 30.30.01.00059/02 11.2014 www.schmalz.com Note These operating instructions were written in the German language. This
More informationRASP RX3 Feed UnitTM SPONGE-JET USER MANUAL. Sponge-Jet, Inc. (USA) 14 Patterson Lane Newington, NH
SPONGE-JET RASP RX3 Feed UnitTM USER MANUAL Sponge-Jet, Inc. (USA) 14 Patterson Lane +1-603-610-7950 Newington, NH 03801 www.spongejet.com Sponge-Jet RASP RX3 User Manual - REV A / DOC: MKT-014-ENG SPONGE-JET
More informationOPERATOR S MANUAL SPREADER. CSS, VNQ [For Combine Harvester AW82V] Original instructions
OPERATOR S MANUAL SPREADER CSS, VNQ [For Combine Harvester AW82V] en Original instructions Introduction Introduction Please read this operator s manual before using your spreader. We would first like to
More informationOperating Instructions in compliance with Pressure Equipment Directive 2014/68/EU. FAS Brass Check Valve RDL
Operating Instructions in compliance with Pressure Equipment Directive 2014/68/EU FAS Brass Check Valve RDL Please read these operating instructions carefully to ensure a safe operation and keep the same
More informationRIX COMPRESSORS. MICROBOOST Owner s Manual CONFIGURATION A MB-115 MB-230. November 21, 2002 APPLICABILITY [ A]
RIX COMPRESSORS MICROBOOST Owner s Manual CONFIGURATION A MB-115 MB-230 November 21, 2002 APPLICABILITY [ A] INTRODUCTION Safety This electromechanical equipment is designed to produce high pressure gas.
More informationAIR HAMMERS MODEL NO: CAT138/CAT139 OPERATING & MAINTENANCE INSTRUCTIONS PART NO: / GC064
AIR HAMMERS MODEL NO: CAT138/CAT139 PART NO: 3120152 /3120153 OPERATING & MAINTENANCE INSTRUCTIONS GC064 INTRODUCTION Thank you for purchasing this CLARKE Air Hammer. Before attempting to use this product,
More informationLRS(H)4 Pressure-Reducing Regulator User Manual
LRS(H)4 Pressure-Reducing Regulator User Manual Read the complete manual before installing and using the regulator. 2 Safe Product Selection When selecting a product, the total system design must be considered
More information170-CG Feed Unit SPONGE-JET USER MANUAL. Sponge-Jet, Inc. (USA) 14 Patterson Lane Newington, NH
SPONGE-JET 170-CG Feed Unit USER MANUAL Sponge-Jet, Inc. (USA) 14 Patterson Lane +1-603-610-7950 Newington, NH 03801 www.spongejet.com AUGUST 2014, Sponge-Jet 170-CG User Manual - REV A / DOC: M-MKTG-002ENG
More informationDeclaration of Conformity as per Directive 97/23/EC
Declaration of Conformity as per Directive 97/23/EC The manufacturer declares that:, 47906 Kempen, Germany Continuous, inline sampling valves Series 27f, with packing Operate with either; Star lever, or
More informationAIR INLINE METAL SHEAR
AIR INLINE METAL SHEAR ASSEMBLY and OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd. / Camarillo, CA 93011 Copyright 1997 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork
More informationInstructions. Control Solution ICF 20-4, ICF 25-4, ICF ICF 40-4, ICF 20-6, ICF 25-6, ICF 32-6, ICF 40-6, Direction and position.
027R9782 Instructions Control Solution ICF 20-4, ICF 25-4, ICF 32-4. ICF 40-4, ICF 20-6, ICF 25-6, ICF 32-6, ICF 40-6, Direction and position ICF xx-4 ICF xx-6 ICF xx-4 / ICF xx-6 with ICM ICM 027R9782
More informationoriginal operating manual Operating manual TankQuick 100 F2 Translation of the Item-No.:
Operating manual TankQuick 100 F2 Item-No.: 013895201 Translation of the original operating manual Important! Copyright The operating manual is always to be read before commissioning the equipment. No
More informationManual Actuated Boiler Blowdown Valves
Manual Actuated Boiler Blowdown Valves Installation and Maintenance Instructions 1. Safety information 2. General product information 3. Installation 4. Operation 5. Maintenance 6. Spare parts p.1 1. Safety
More informationType BBS-03, BBS-05, BBS-06, BBS-25
Type BBS-03, BBS-05, BBS-06, BBS-25 Sterile connection elements Sterile Verbindungselemente Raccords union stériles Operating Instructions Bedienungsanleitung Manuel d utilisation 1. THE OPERATING INSTRUCTIONS
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 1-1/4 INCH BRAD NAILER Model: 7611 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More information24L AIR COMPRESSOR MODEL NO: TIGER 8/260 PART NO:
24L AIR COMPRESSOR MODEL NO: TIGER 8/260 PART NO: 1499490 OPERATION & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS LS0918 - ISS 2 INTRODUCTION Before attempting to use this product, please read this
More informationATD LB PRESSURE BLASTER INSTRUCTION MANUAL
ATD-8402 90LB PRESSURE BLASTER INSTRUCTION MANUAL SAVE THESE INSTRUCTIONS SAFETY INSTRUCTIONS FOR SANDBLASTER 1. Before opening the tank release the air pressure on the sand tank. To do this, turn off
More information1/2 REVERSIBLE AIR DRILL
1/2 REVERSIBLE AIR DRILL MODEL NO: CAT60 PART NO: 3110460 OPERATING & MAINTENANCE INSTRUCTIONS GC0614 INTRODUCTION Thank you for purchasing this CLARKE Reversible Air Drill. Before attempting to use this
More information24 Litre Air Compressor
Operator s Manual 24 Litre Air Compressor WARNING! Before using this appliance, read the Operator s manual and follow all its safety rules and instructions. SPECIFICATION Model Power ITEM DATA HWKAC2 1Kw/1.5HP&1.5Kw/2HP&1.8Kw/2.5HP
More informationTECHNICAL DATA MAINTENANCE AIR COMPRESSOR MODEL G-1
Dry 131h 1. DESCRIPTION The Viking Model G-1 Maintenance Air Compressor is an electric motor-driven, aircooled, single-stage, oil-less compressor. The unit is equipped with a check valve and provides a
More informationPneumatic switch module 3/2-way valve (On/Off) Types P Types FP Function tested for use of the float in Ex-zone 0
Operating Manual LTIA3E Pneumatic switch module 3/2-way valve (On/Off) Types P Types FP Function tested for use of the float in Ex-zone 0 Contents 1. Safety Instructions 2. Conformity to standards 3. Technical
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More informationDifferential Pressure Regulator Type Type 45-6 (0.1 to 1 bar, DN 15) Mounting and Operating Instructions EB 3226 EN
Differential Pressure Regulator Type 45-6 Type 45-6 (0.1 to 1 bar, DN 15) Mounting and Operating Instructions EB 3226 EN Edition March 2008 Contents Contents Page 1 Design and principle of operation...................
More informationType 0404 / /2-way solenoid valve 2/2-Wege-Magnetventil Électrovanne 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation
Type 0404 / 5404 2/2-way solenoid valve 2/2-Wege-Magnetventil Électrovanne 2/2 voies Operating Instructions Bedienungsanleitung Manuel d utilisation 1 OPERATING INSTRUCTIONS The operating instructions
More informationOPERATION MANUAL NTF-15
OPERATION MANUAL NTF-15 Nitrogen Tire Filling Valve Stem Caps (Qty=200) Order P/N 436075 RTI Technologies, Inc 10 Innovation Drive York, PA 17402 800-468-2321 www.rtitech.com 035-81235-00 (Rev B) TABLE
More informationMANUAL. Sesame. Thermoplastic Tank Technologies
MANUAL Sesame Thermoplastic Tank Technologies INSTALLATION AND USER GUIDE CONTENT 1. GENERAL 3 2. IMPORTANT 3 3. INSTALLATION EXPANSION VESSEL 4 4. USE EXPANSION VESSEL 5 5. AIR CELL REPLACEMENT 5 5.1
More informationComponents for air preparation and pressure adjustment. OUT port position ( ) connected Rear side. of IN port. Air tank. directly.
Components preparation and pressure adjustment ABP Overview ABP is a component that enables boosting by s only up to twice primary pressure (.0MPa max.) in combination with using air tank but not using
More informationSC100V AIR COMPRESSOR
SC100V AIR COMPRESSOR OWNER S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE. SPECIFICATION ITEM DATA Model SC100V Power 2.2 Kw / 3 HP Voltage 230 V Frequency
More informationaccidents which arise due to non-observance of these instructions and the safety information herein. SPECIFICATIONS
18 GAUGE 2 INCH BRAD NAILER Model: 7555 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry.
More informationCB 350. Spare parts list. Hydraulic concrete buster. CB 350 s/n DEQ Construction Tools GmbH No
CB 350 Spare parts list Hydraulic concrete buster CB 350 s/n DEQ179000-2018 Construction Tools GmbH No. 3390803501 2018-01-01 General information This spare parts list applies to the following: Part number
More information2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL
2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL Model: 52024 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement,
More informationA17W23_MASE_MUS_EN MANUAL
A1W2_MASE_MUS_EN MANUAL CONTENTS 1 Identification 1.1 Manufacturer 1.2 Product name 1. Year of manufacture 1. Area of use 2 Technical specification 2.1 Design 2.2 Function 2. Technical data 2. Security
More informationBooster Pump PB4-60 Replacement Kits
Booster Pump PB4-60 Replacement Kits FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product
More information