ANNUAL IDOL COMPLIANCE TRAINING
|
|
- Leslie Wilson
- 5 years ago
- Views:
Transcription
1 ANNUAL IDOL COMPLIANCE TRAINING Lock Out / Tag Out Refresher SUGAR GROVE FIRE DEPARTMENT 1 TRAINING DIVISION
2 Instructions To complete this independent study program, view the entire program, advancing through each slide by pressing the enter key. While viewing the slides, complete the accompanying Independent Study Test. If needed, you can move backwards through slides by pressing the backspace key. Start the program by pressing enter. 2
3 Purpose The primary purpose of the Lock Out/Tag Out Program is to prevent the unintended release of hazardous energy while emergency response personnel are working on or around equipment or energy sources [ENERGY CONTROL PLAN]. Energy sources that are not neutralized and locked out have the potential to cause severe injury, disfigurement, or death from electric shock, contact with rotating machinery, burns and other causes. 3
4 Scope Lock Out/Tag Out procedures are required when it is necessary to work on or around any equipment that that may release any form of hazardous energy, including, but not limited to electrical, rotational, mechanical, radiation, chemical, hydraulic, thermal or pneumatic energy sources. 4
5 OSHA Regulations Confined space operations are regulated by OSHA Requires employers whose personnel may be called upon to respond to emergencies involving work on or around hazardous energy sources to receive training at initial assignment of duties and each year thereafter. 5
6 OSHA Regulations 29 CFR The control of hazardous energy This is the standard that governs the need to Lock Out/ Tag Out machines/ equipment while be serviced by employees 6
7 What is Lock Out/Tag Out? Procedure for a safe shut down and restart of equipment that is serviced or maintained Lock Out protects employees who service and maintain equipment Tag Out warns employees of the shut down Applies to outside contractors working on premises. 7
8 Lock Out/Tag Out Prevents Equipment from unexpectedly starting-up Co-workers from restarting equipment Injury and death during servicing or maintenance of equipment 8
9 Leading Causes of Lock Out/Tag Out Injuries Failure to shut off equipment Failure to disconnect from power source Unexpected restarting of equipment Failure to clear work area before restarting 9
10 Authorized Employees Must Maintain or service equipment Identify all energy sources Inform others of Lock Out/Tag Out in progress Follow the Lock Out/Tag Out procedures 10
11 Affected Employees Operate or use equipment Understand all Lock Out/Tag Out procedures Never remove locks or tags Never restart equipment with lock or tag 11
12 Other Employees Are not authorized or affected employees Must be able to identify locks and tags Must be aware of Lock Out/Tag Out procedures Never restart equipment with lock/tag 12
13 Energy Control Devices An energy isolation device is a mechanical device that physically prevents the transmission or release of energy. These devices ensure a zero energy state during fire suppression and rescue activities. 13
14 Locks Master Locks are used by the Sugar Grove Fire Department 14
15 Other Lockout Devices Other devices used in conjunction with locks are tags, chains, valve bonnets, and other hardware for the isolating, securing or blocking of machines or equipment from energy sources. 15
16 Personal Danger Tags Personal Danger Tag Used for personal protection during lockout. Removed once personnel have vacated the area. 16
17 Personal Danger Tags Used for firefighter protection. Used in conjunction with a lock every time. Must be removed when task completed. 17
18 Equipment Danger Tags Equipment Danger Tag Used to designate equipment in need of repair. Left on equipment until repairs are made by maintenance personnel Example would be a saw coming out of service for repair work. Length of hose with a bad coupling rolled backward on hose rack 18
19 Equipment Danger Tags Designates equipment in need of repair. Tag attached by Company Officer reported to Lt. Warner and person responsible for that piece of equipment. Placed on equipment using wire tie only. Example would be an SCBA coming out of service for a malfunction. Tag SCBA unit and report to Lt. Warner and Lt. 19 Schramm.
20 Lockout Procedure Preparation for Shutdown. Shutdown. Isolation. Lock and Tag. Verification. During Verification, the system must be tested and checked for stored energy. 20
21 Tag Only Procedure Used only when the equipment is not physically capable of accepting a lock or when placing a lock on the equipment is considered to be a danger itself. Firefighter safety must be assured to a level of safety equivalent to that obtained by using locks and tags. 21
22 Tag Only Procedure Verify Device will not accept Lock. Document Equivalent Safety Plan Apply Tag with Wire Tie Complete Tag Only Authorization Attach Documentation to Run Report. 22
23 Six Steps to Performing Lock Out/Tag Out Safely Step One - Prepare for shutdown Step Two - Shutdown equipment 23
24 Six Steps to Performing Lock Out/Tag Out Safely Step Three - Disconnect power source using an energy isolating device 24
25 Six Steps to Performing Lock Out/Tag Out Safely Step Four - Apply Lock Out/Tag Out devices Only applied by authorized employees Locks hold power source in off position Locks must be used if equipment is capable of being locked out If locks cannot be used tags must be used 25
26 Six Steps to Performing Lock Out/Tag Out Safely Step Four - Apply Lock Out/Tag Out devices Devices must be: Standardized Identifiable Durable Not used for other purposes 26
27 Six Steps to Performing Lock Out/Tag Out Safely Step Four - Apply Lock Out/Tag Out devices Limitation of tags: Only a warning device Equipment can still be started-up False sense of security 27
28 Six Steps to Performing Lock Out/Tag Out Safely Step Five - Release stored energy Step Six - Verify machine is safe 28
29 Restarting the Equipment Inspect work area Notify employees Remove devices Test equipment 29
30 Group Lock Out Group Lock Out device used when more than one person services the equipment Each employee has own lock or tag One primary employee responsible Shift changes require group Lock Out device 30
31 Removing Another Employee s Lock or Tag If a lock or tag needs to be removed and the employee cannot be found: Verify employee is not in facility (used when Company Officer applying lock and/or tag is not available to remove the devices.) Make reasonable effort to contact employee Evaluation, Verification and Removal will be performed by the Incident Commander, Safety Officer, Deputy Chief or Chief. Tell employee about removal 31
32 Instructions Answer the test questions on the Bubble Answer Sheet. Sign reverse side of the Answer Sheet for validation and attestation of training completed. Place completed test in Assistant Chief Baum s s mail box for assessment. A passing grade of 80% is required to get credit for this Mandatory Training A failure in submitting completed materials will result in not receiving credit for the Mandatory Training which can lead to disciplinary actions. 32
LOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM
LOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.147 BASIS: Approximately three million workers in the United States face risks from uncontrolled energy when servicing machinery
More informationUniversity of Arkansas Office of Environmental Health and Safety
University of Arkansas Office of Environmental Health and Safety Procedure Name: Lockout / Tagout Procedure Number: 600.26 Effective Date: 12-1-2015 Procedure: Developed in accordance with the OSHA Control
More informationLOCKOUT/TAGOUT PLAN August 2015
LOCKOUT/TAGOUT PLAN August 2015 Office of Environmental Health and Safety 423-354-5224 TABLE OF CONTENTS Purpose and Intended Use... 2 A. Types of Energy Sources... 2 B. Activities Requiring Lockout/Tagout
More informationLockout/Tagout Program
Purpose Hazardous energy appears in the workplace in the form electrical, mechanical, pneumatic, hydraulic and thermal energy and includes chemical, water, steam and gaseous energy systems. Lockout/Tagout
More informationHazardous Energy Control Lockout/Tagout
Hazardous Energy Control Lockout/Tagout Debbie Rauen INSafe Safety Consultant Outline Energy Sources Employer Responsibilities Authorized Employee Responsibilities Energy Control (LO/TO) Equipment & Devices
More informationControl of Hazardous Energy (Lockout/Tag-out) 29 CFR
Control of Hazardous Energy (Lockout/Tag-out) 29 CFR 1910.147 What Is Lockout/Tag-out? Referred to as LOTO Blocks flow of energy from power source to the equipment Provides means of warning (tag) Regulatory
More informationLockout/Tagout - Control of Hazardous Energy Program
Lockout/Tagout - Control of Hazardous Energy Program The University Of Iowa Environmental Health & Safety 122 Grand Avenue Court Iowa City, IA 52242-1000 Phone: 319-335-8501 Date Revised/Reviewed: 6/8/2018
More informationARKANSAS TECH UNIVERSITY FACILITIES MANAGEMENT HEALTH AND SAFETY MANUAL (LOCKOUT/TAGOUT) 30.0
() 30.0 The purpose of the Energy Control Policy (Lockout/Tagout) is to ensure that before any employee performs any servicing and/or maintenance on machinery or equipment, where the unexpected energizing,
More informationCONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM
CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM 1.0 REGULATORY AUTHORITY Code of Federal Regulations, 29 CFR 1910.147; California Code of Regulations, Title 8, Sections 2320.1 and 3314; CSU, Fullerton
More informationLockout/Tagout Program
Lockout/Tagout Program Prepared by: Occupational Health and Safety Reviewed by: Joint Health and Safety Committees Approved by: Chief Human Resources Officer November 2014 TABLE OF CONTENTS 1.0 Purpose...3
More informationLockout/Tagout Safety Policy
University of North Carolina Wilmington Environmental Health & Safety Workplace Safety Lockout/Tagout Safety Policy GENERAL The UNCW Environmental Health & Safety Department (EH&S) is authorized by UNCW
More informationLockout / Tag out Program
Lockout / Tag out Program Presented by DOSHTI www.doshti.com You will learn Purpose of Lockout- Tag out Requirements for LOTO Types of Hazardous Energy Procedures for LOTO The OSHA Standard for the Control
More informationLockout Tagout Program
Lockout Tagout Program RIM of the World Unified School District 27315 North Bay Road Blue Jay, CA 92352 (909) 336-4100 July 2016 Safety and Risk Management Department RIM of the World Unified School District
More informationControl of Hazardous Energy Lockout / Tagout Program
Control of Hazardous Energy Lockout / Tagout Program August 2016 Table of Contents Purpose... 1 Scope and Application... 1 Responsibilities... 1 Environmental Health and Safety Personnel (EH&S)... 1 Directors
More informationRiskTopics. Lockout/Tagout October 2017
RiskTopics Lockout/Tagout October 2017 This Risktopic is designed to outline guidelines for lockout/tagout and provide assistance in developing a management program to reduce the risk of injury from unintended
More informationLockout Tagout Policy
Office of Environmental Health & Safety www.moreheadstate.edu/ehs 606-783-2584 Lockout Tagout Policy PURPOSE To establish procedures for the de-energization and isolation of energy sources or the lockout
More informationLock Out/Tag Out Control of Hazardous Energy
Lock Out/Tag Out Control of Hazardous Energy University Facilities Internal Procedure: July 1, 2013 Effective date: July 1, 2013 Last Modified: April 2013 Approved by: Bob Wells 1.0 Program Objective UF
More informationHealth and Fire Safety Review 2/15
Health and Fire Safety Review 2/15 1 TABLE OF CONTENTS Page 3 Scope 3 Control of Hazardous Energy (Introduction) 3 Authorized Employee 3 Employer Responsibility 4 Tagout Devices 4 Lockout Devices 5 General
More informationCONTROL OF HAZARDOUS ENERGY IN THE WORKPLACE
Office of Environmental Health & Safety CONTROL OF HAZARDOUS ENERGY IN THE WORKPLACE LOCK OUT/TAG OUT OSHA 29 CFR 1910.147 rev. 3 2014 Director of Environmental Health & Safety Control of Hazardous Energy
More informationThis session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its
This session covers the safety procedure known as lockout/tagout, which is required by Occupational Safety and Health Administration (OSHA) in its standard on Control of Hazardous Energy. This is part
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT) PROGRAM
Page: 1 of 15 1.0 Purpose and Applicability 2.0 Scope 1.1 It is the policy of the University of Pennsylvania in coordination with the Office of Environmental Health and Radiation Safety to provide the
More informationProduct Information Report Lockout/Tagout Hazardous Energy Control
Overview A properly implemented (LOTO) program is designed to protect workers involved in the maintenance and servicing of equipment from the dangerous effects of hazardous energy caused by the unexpected
More informationOKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM. Environmental Health and Safety. Established:
OKLAHOMA CITY COMMUNITY COLLEGE CONTROL OF HAZARDOUS ENERGY PROGRAM Environmental Health and Safety Established: Developed in accordance with OSHA Standard 29 CFR 1910.147 1 1.0 SCOPE. Oklahoma City Community
More informationLockout - Tagout. Control of Hazardous Energy OSHA Standard
Lockout/Tagout Lockout - Tagout Control of Hazardous Energy OSHA Standard 1910.147 What Is Lockout/Tagout? Referred to as LOTO Blocks the flow of energy from power source to the equipment Provides means
More informationHazardous Energy Control (Lockout-Tagout)
Hazardous Energy Control (Lockout-Tagout) The purpose of this program is to prevent inadvertent operation or energization of machines, equipment, or processes in order to protect employees and establish
More informationSAFETY DIRECTIVE 2.0 DEPARTMENTS AFFECTED. This Administrative Directive shall apply to all Town of Marana departments and employees.
SAFETY DIRECTIVE Title: Control of Hazardous Energy Lock-out/Tag-out/Try-out Issuing Department: Town Manager s Safety Office Effective Date: July 1, 2014 Approved: Gilbert Davidson, Town Manager Type
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAG OUT PROGRAM) Washington State University Tri-Cities (all departments)
CONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAG OUT PROGRAM) Washington State University Tri-Cities (all departments) PURPOSE This program establishes the general and specific requirements for the control of
More informationTHE UNIVERSITY OF NORTH CAROLINA
THE UNIVERSITY OF NORTH CAROLINA AT CHAPEL HILL CHILLED WATER DEPARTMENT ENERGY CONTROL PROCEDURE The purpose of this document is to establish minimum requirements for the manual isolation and securing
More informationLockout/Tagout Program
Lockout/Tagout Program Control of Hazardous Energy Subpart J - 29 CFR 1910.147 29 CFR 1926.417 OSHA Standard All industries must comply Estimated to prevent Approximately 120 fatalities per year 28,000
More informationDRAFT LOCKOUT/TAG OUT PROGRAM (CONTROL OF HAZARDOUS ENERGY)
DRAFT [name of unit] LOCKOUT/TAG OUT PROGRAM (CONTROL OF HAZARDOUS ENERGY) PURPOSE This program establishes the general and specific requirements for the control of hazardous energy during the servicing
More informationH. Control of Hazardous Energy: Lockout/Tag Out
H. Control of Hazardous Energy: Lockout/Tag Out 1. Purpose Control of Hazardous energy is the purpose of the Lockout- Tagout Program. This program establishes the requirements for isolation of both kinetic
More informationPAGE 1 OF 7 HEALTH, SAFETY & ENVIROMENTAL MANUAL PROCEDURE: S230 Lock-Out Tag-Out (LOTO) Program REV 4.0 8/13/2012
PAGE 1 OF 7 LOCK-OUT TAG-OUT (LOTO) THE CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM PURPOSE: 1. This standard establishes lockout/tagout (LOTO) procedures for the safety of personnel working on
More informationFacilities Management
Facilities Management Policy Number: 700.6 Title: Lockout/Tag Out Policy Implementation Date: 2004 Last Audited: July 2 nd, 2018 Last Revised: March 25 th, 2015 Introduction This policy contains the necessary
More informationLockout / Tagout Program OSHA 29 CFR
Lockout / Tagout Program OSHA 29 CFR 1910.147 Baylor University utilizes outside contractors to perform set-up, maintenance, service, and repair to equipment utilized on campus. University staff perform
More informationLockout / Tagout Safety Program
Lockout / Tagout Safety Program Prepared by: The Ohio State University Environmental Health and Safety Occupational Safety & Industrial Hygiene 1314 Kinnear Road Columbus, OH 43212-1168 614-292-1284 Phone
More informationLockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR
Volunteer State Community College Lockout/Tagout Program Occupation Safety & Health Standards for General Industry 29 CFR 1910.147 The information contained in this maual documents the policies and procedures
More informationLockout/Tagout Manual
Manual 2408 Wanda Daley Drive Ames, Iowa 50011-3602 (515) 294-5359 www.ehs.iastate.edu Copyright Environmental Health and Safety 2809 Daley Drive Ames, IA 50011-3660 Ph: (515) 294-5359 www.ehs.iastate.edu
More informationGettysburg College. Energy Control Program
Gettysburg College Energy Control Program Adopted October 2009 Reviewed and Updated February 2015 Reviewed and Updated July 2015 I. Energy Control Procedures Table of Contents A. General Lockout Procedures
More information230-LOCKOUT/TAGOUT PROGRAM
230.1 PURPOSE A. To confirm implementation, operation, and recordkeeping of Central New Mexico Community College(CNM) lockout/tagout program in compliance with 29 CFR 1910.147. 230.2 SCOPE A. The requirements
More informationIsolation and Lockout
Work Procedure Facilities Management UBCO-RMS-OHS-WP 16-001 Date Created: July 13, 1999 Date Updated: April 4, 2016 Supersedes: September 18, 2003 1. SCOPE Isolation and Lockout This procedure establishes
More informationLOCKOUT-TAGOUT PROGRAM
LOCKOUT-TAGOUT PROGRAM Please Note: This material, or any other material used to inform employers/employees of compliance requirements of OSHA standards through simplification of the regulations should
More informationPage: 7/15/2009. Energy control procedures Use of lockout/tagout equipment to ensure safe work practices.
1 of 6 1.0 PURPOSE This program applies to the installation, service, maintenance, or removal of any type of machinery, equipment, or components, in which the unexpected start up or release of stored energy
More informationPINNACLE OWNING SAFETY: Zero Fires Zero Loss Incidents 100% Employee Engagement
PINNACLE OWNING SAFETY: Zero Fires Zero Loss Incidents 100% Employee Engagement ENERGIZED WORK PERMIT OVERVIEW Effective January, 2016 ENERGIZED WORK DEFINITION Energized work describes work that must
More informationLockout Tagout Program
Lockout Tagout Program Table of Contents INTRODUCTION... 2 FORWARD... 2 OBJECTIVE... 2 APPLICABILITY... 2 RESPONSIBILITIES... 3 PROGRAM ENFORCEMENT... 4 RECORDKEEPING... 4 LOCKOUT TAGOUT EQUIPMENT... 5
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
1. De-energize circuit serving the outlet following LOTO procedure (see pages 3 5). PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All
More informationUniversity of Vermont Department of Physical Plant Burlington, Vermont
University of Vermont Department of Physical Plant Burlington, Vermont CONTROL OF HAZARDOUS ENERGY SOURCES AND ELECTRICAL HAZARDS LOCKOUT AND TAGOUT PROGRAM in accordance with OSHA 29 CFR 1910.147 REVISED
More informationHealth, Safety, Security and Environment
Document owner and change code Document Owner Aaron Perronne Title HSSE Manager Mark X Change Code Description X N/A First Issue A Typographical/Grammatical correction; formatting change; text clarification-no
More informationLO/TO LOCKOUT/TAGOUT PROGRAM
LO/TO LOCKOUT/TAGOUT PROGRAM April 2017 CONTENTS Section 1: Introduction...1 Section 2: Purpose... 1 Section 3: Application... 1 Section 4: Definitions... 2 Section 5: Roles and Responsibilities... 4 Section
More informationDUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM
DUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Introduction 2 Regulatory Requirements 2 Protective Materials
More informationElements of a Lockout/Tagout Program OSHA
September 15, 2015 Elements of a Lockout/Tagout Program OSHA 1910.147 Dayna Noble Industrial Safety Consultant Specialist Ohio BWC 567-204-8917 Dayna.noble@bwc.state.oh.us Top 10 most frequently cited
More informationEnergy Control Procedures Lockout/Tagout 29 CFR
Energy Control Procedures Lockout/Tagout 29 CFR 1910.147 Paul Schlumper, PE, CSP Georgia Tech Research Institute What is covered? Servicing and maintenance Normal production operations where: Employees
More informationUniversity of Illinois at Chicago. Control of Hazardous Energy Program (Lockout/Tagout)
University of Illinois at Chicago Control of Hazardous Energy Program (Lockout/Tagout) 10/4/2018 UNIVERSITY OF ILLINOIS AT CHICAGO Control of Hazardous Energy (Lockout/Tagout) Program TABLE OF CONTENTS
More informationMARIPOSA COUNTY LOCKOUT/TAGOUT PROGRAM
MARIPOSA COUNTY LOCKOUT/TAGOUT PROGRAM INTRODUCTION Mariposa County ( County ) facilities have equipment and systems that must be deenergized to allow for safe cleaning, repairing, servicing, setting-up,
More informationControl of Hazardous Energy. Environmental Health and Safety
Control of Hazardous Energy Environmental Health and Safety 11/01/2014 1 CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT) OSHA CFR 1910.147 Revised Date: November 2014 STATEMENT OF POLICY Ball State University
More informationPRESCOTT SCHOOL DISTRICT NO South A Street Prescott, WA The Control of Hazardous Energy (Lockout/Tagout)
PRESCOTT SCHOOL DISTRICT NO. 402-37 207 South A Street Prescott, WA 99348 509-849-2217 The Control of Hazardous Energy (Lockout/Tagout) I. Purpose The Control of Hazardous Energy (Lockout/Tagout) This
More informationWESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107
WESTERN CONNECTICUT STATE UNIVERSITY LOCKOUT/TAGOUT PROCEDURE S-107 Draft Issued 12/97 Revised 11/00 Please direct any questions or comments about the applicability of this document to Luigi Marcone, WCSU
More informationLOCKOUT/TAGOUT: Operating Procedure TABLE OF CONTENTS
LOCKOUT/TAGOUT: Operating Procedure TABLE OF CONTENTS A. PURPOSE 1 B. FACILITIES STAFF RESPONSIBILITIES 2 C. TRAINING AND RETRAINING of AFFECTED and EUTHORIZED EMPLOYEES 3 NINE POINTS TO REMEMBER 5 LOCKOUT/TAGOUT
More informationControl of Hazardous Energy Program (Lockout/Tagout)
Control of Hazardous Energy Program (Lockout/Tagout) 1 The Control of Hazardous Energy (Lockout/Tagout) Program 1910.147 The following lockout/tagout program is provided to assist employees in complying
More informationLockout/Tagout - Energy Control Program
Lockout/Tagout - Energy Control Program Lockout and Tagging of ELECTRICAL Circuits This portion of the K.R. Miller Contractors, Inc. safety program has been created to maintain a written copy of procedures
More informationLOCKOUT/TAGOUT PROGRAM
Santa Clarita Community College District LOCKOUT/TAGOUT PROGRAM Revised March 2018 TABLE OF CONTENTS PURPOSE... 3 COMPLIANCE...4 DEFINITIONS...5 SECTION I - ENERGY CONTROL PROCEDURES... 7 SECTION II -
More informationPART Q CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT)
PART Q CONTROL OF HAZARDOUS ENERGY (LOCKOUT-TAGOUT) WAC Page 296-307-320 Control of hazardous energy (lockout-tagout). 1 296-307-32001 What does this section cover? 1 296-307-32003 When does this section
More informationSAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT
SAMPLE WRITTEN PROGRAM for Control of Hazardous Energy LOCKOUT TAGOUT SAMPLE WRITTEN PROGRAM The objective of this procedure is to establish a means of positive control to prevent the accidental starting
More informationPALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT
PALM BEACH STATE COLLEGE PERSONAL PROTECTIVE EQUIPMENT (PPE) JOB HAZARD ASSESSMENT Department: Facilities Campus: All Task: Replace a Light Ballast Job Title(s) Performing Task: Electrician, Maintenance
More informationHealth & Safety Policy and Procedures Manual SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY
SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY 1. CONTROL OF HAZARDOUS ENERGY POLICY AND PROCEDURES A. OSHA References: 29 CFR 1910.147, 29 CFR 1910.332, 29 CFR 1910.333, 29 CFR 1926.417 B.
More informationLockout/Energy Control
Lockout/Energy Control Presented By: Sotaris, LLP 2000 Auburn Drive, Suite 200 Beachwood, Ohio 44122 P: 216-378-7650 F: 866-794-5756 W: www.sotaris.com E: awj@sotaris.com 1 About Me Andrew W. Johnson,
More informationEnergy Control. Suite 2A, 55 Frid Street Hamilton, ON L8P 4M3 office: cell:
Energy Control Suite 2A, 55 Frid Street Hamilton, ON L8P 4M3 office: 905.577.0303 cell: 905.977.0210 consultant@staffaid.ca www.staffaid.com Safety, Energy Control, Power Lockout & Function Test Procedures
More informationLOCKOUT / TAGOUT PROGRAM
LOCKOUT / TAGOUT PROGRAM Developed in accordance with the OSHA Control of Hazardous Energy Standard, 29 CFR 1910.147 DECEMBER 7, 2017 SKIDMORE COLLEGE 815 NORTH BROADWAY, SARATOGA SPRINGS, NY 12866 Table
More information2008. AURORA PICTURES
2923 LOCKOUT/TAGOUT: It Would Have Saved His Life 2008. AURORA PICTURES 1 Table of Contents Introduction 3 Video Overview.3 Introduction 3 Purpose of Lockout/Tagout 3 Hazardous Energy Sources.3 Authorized
More informationLOCKOUT/TAGOUT PROGRAM
LOCKOUT/TAGOUT PROGRAM HOW CLIMATE ENGINEERS INC. COMPLIES WITH THELO/TO STANDARD It is the intent of Climate Engineers Inc. to comply with OSHA s Control of Hazardous Energy Standard (1910.147). The following
More informationLockout/Tagout Plan Environmental Health & Safety Office July 2017
July 2017 Table of Contents Acronyms... iii Foreword... iv Document History... iv 1.0 Introduction... 1 1.1 Purpose... 1 1.2 Scope... 1 1.3 Lockout/Tagout Program... 1 2.0 Roles and Responsibilities...
More informationLock Out - Tag Out Safety Program
Lock Out - Tag Out Safety Program Daniel Schmid 4-22-15 Pam Schmid 4-22-15 Dan Schmid Pam Schmid Safety Director Quality Director Table of Contents DOCUMENT REVISION TABLE... 3 PURPOSE... 4 RESPONSIBILITY...
More informationLOCKOUT SYSTEM AND POLICIES
LOCKOUT SYSTEM AND POLICIES Lockout System Purpose Employees health and safety takes top priority. Isolating hazardous energy to prevent sudden and unexpected energisation of machines, equipment, and processes
More informationUCHC Lockout/Tagout Policy (4/09)
UCHC Lockout/Tagout Policy (4/09) Background: This safety policy is applicable to all Health Center activities and addresses practices and procedures that are necessary to disable machinery or equipment
More informationDuPage County Environmental, Safety, Health & Property Loss Control Program Hazardous Energy Control (Lockout/Tagout)
Purpose: To provide the minimum requirements for the lockout or tagout of energy isolating devices whenever work is performed or servicing is done on County of DuPage machinery, equipment, vehicles and
More informationHazardous Energy Control
Lockout Tagout This program has been prepared to provide assistance in compliance with USA OSHA standards and/or Best Management Practices. It should not be used without consideration of the unique conditions
More informationCONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT)
CONTROL OF HAZARDOUS ENERGY (LOCKOUT/TAGOUT) 1. PURPOSE The purpose of this program is to establish policy, rules and procedures for the protection of employees against the unexpected energizing, start-up,
More informationHazardous Energies Control and Lockout/Tagout Program
Hazardous Energies Control and Lockout/Tagout Program Summary: This program applies to the installation, service, maintenance, or removal of any type of machinery, equipment, or components, in which the
More informationCentral Washington University
Central Washington University Lockout / Tagout (LOTO) Program Plan prepared by: Central Washington University Office of Environmental Health & Safety 400 East University Way Ellensburg, WA 98926 P: 509-963-2252
More information2523-LDG-E. Leader s Guide
2523-LDG-E LOCKOUT/TAGOUT TRAINING FOR EMPLOYEES Leader s Guide 2008 ERI Safety Videos LOCKOUT/TAGOUT TRAINING FOR EMPLOYEES This easy-to-use Leader s Guide is provided to assist in conducting a successful
More informationIssue: Issued By: Environment, Health & Safety Part: Hazard Identification and Assessment Revision #: 2 Revision
Control of Hazardous Energy Program Section: Occupational Health and Safety Date of 2007.07.24 Management System Issue: Issued By: Environment, Health & Safety Part: Hazard Identification and Assessment
More informationTHE OSHA LOCK-OUT/TAG-OUT STANDARD
PRESENTER'S GUIDE "LOCK-OUT/TAG-OUT" Training for THE OSHA LOCK-OUT/TAG-OUT STANDARD Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS OUTLINE OF MAJOR PROGRAM
More informationEnvironmental Health and Safety (EH&S) Revision Date: Initial. Prepared by: EH&S and Facility Management and Campus Services (FMS)
Environmental Health and Safety (EH&S) Energy Control Procedure (Lockout/Tagout/Tryout) Date of Issuance: 1/1/2019 Revision Number: Initial Revision Date: Initial Prepared by: EH&S and Facility Management
More informationManagement Plan for Lockout Tagout (LOTO) ISD #535
Management Plan for Lockout Tagout (LOTO) ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9½ Street Rochester, MN 55904 507-328-4507 Modification Date Document Modification Form All
More informationSOP GEN-007I Energy Isolation
Page 1 of 6 1.0 Introduction 2.0 Reference 3.0 Scope 4.0 Procedures 5.0 Permit SOP GEN-007I Revision/ Review Log Revision Date Approved by Reviewed by Revision Details/ Proposal Notes 11 January 2010 HSE
More informationSafety Manual: Hazardous Energy. January, 2017
Safety Manual: Hazardous Energy January, 2017 9.0 Hazardous Energy Introduction Energized equipment in the workplace pose a significant risk of injury and death. If the unexpected energization or start-up
More informationEM Section 12. Control of Hazardous Energy (Lockout/Tagout)
EM 385-1-1 Section 12 Control of Hazardous Energy (Lockout/Tagout) Lockout/Tagout References EM 385-1-1 Section 12 29 CFR 1926.600 (a) (3) i Heavy Equipment 29 CFR 1926.702 (j) (1) Concrete Tools 29 CFR
More informationLOCKOUT/TAGOUT POLICY
NAVAJO COUNTY Safety Procedures Reference: PERSONNEL POLICIES & PROCEDURE SECTION: 5.4 Approved: Brett Starns Subject: LOCKOUT/ RM-Safety 09/04/2014 TAGOUT POLICY Revised: 9/16/2014 Initiating Department:
More informationPROGRAM: Control of Hazardous Energy (LOCKOUT) Chapter 5
Classroom, Occupational Safety & Health Plan Date: August 5, 2017 PROGRAM: Control of Hazardous Energy (LOCKOUT) Chapter 5 1. Purpose This document establishes the Lockout Program for Tidewater Community
More informationLOCKOUT/TAGOUT PROGRAM
0 Appendix C OCCUPATIONAL SAFETY AND HEALTH PROGRAM LOCKOUT/TAGOUT PROGRAM Hazardous Energy Control Lockout/Tagout Program TABLE OF CONTENTS Section Page I. Purpose and Scope. 1 II. Definitions 1 III.
More informationThe Proper Procedure
The Proper Procedure Lockout Lockout is used to prevent the release of hazardous energy or equipment from starting by applying a lockout device and lock A padlock is placed on the appropriate energy isolating
More informationLockout/Tagout. Page. Introduction. Purpose. 2 Background. 2 Who s Covered?... 3 Responsibilities. 3 Explanation of Key Terms. 4.
Lockout/Tagout Page Introduction Purpose. 2 Background. 2 Who s Covered?... 3 Responsibilities. 3 Explanation of Key Terms. 4 How It Works General Lockout/Tagout Procedure. 5 General Lock/Tag Removal Procedure.
More informationWHS PROCEDURE P Plant Isolation. Approved by: Ruth Hampton Review Date: 6 th December 2015
5 WHS PROCEDURE P29-02 Page 1 of 7 Issue: 2 1. Intent The Salvation Army Australia Eastern Territory (TSA-AUE) is committed to the provision of a safe, healthy and injury free environment within the mission
More informationHazardous Energy Program Lockout/Tagout
Hazardous Energy Program Lockout/Tagout Last Revision Date: 11/7/2016 I. PURPOSE... 2 II. SCOPE... 2 III. REFERENCES... 2 IV. RESPONSIBILITIES... 2 A. Supervisors... 2 B. Employees:... 3 1. Authorized
More informationLOCK OUT \ TAG OUT PROGRAM
LOCK OUT \ TAG OUT PROGRAM University of Portland 5000 N. Willamette Blvd Portland, OR 97203-5798 January 2005 Revision 2.5 Prepared By: Environmental Health and Safety i TABLE OF CONTENTS Content SECTION
More informationLockout Tagout Program
Lockout Tagout Program 1.0 INTRODUCTION Public Safety Department Environmental, Health and Safety (EHS) Division Standard Operating Procedure (SOP) #18 Purpose To ensure that machinery or equipment is
More informationHazardous Energy Control/Lockout
This is a photographic template your photograph should fit precisely within this rectangle. Hazardous Energy Control/Lockout MESH 8.0 - Process Safety Awareness Training 2008 Eaton Corporation. All rights
More informationSAINT MARY S COLLEGE OF CALIFORNIA STANDARD HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT. Prepared by
SAINT MARY S COLLEGE OF CALIFORNIA STANDARD 1.1.4 HAZARDOUS ENERGY CONTROL PROGRAM INCLUDING LOCKOUT/TAGOUT Prepared by SAINT MARY S COLLEGE OF CA MORAGA, California KAREN LAURICELLA Original Date: 1 JULY
More informationSample Written Program for The Control of Hazardous Energy (Lockout/Tagout)
USAG Bavaria Safety Office Sample Written Program for The Control of Hazardous Energy (Lockout/Tagout) Nov 2016 1910.147 The Control of Hazardous Energy (Lockout/Tagout) The following lockout/tagout program
More informationSUNY OSWEGO ENVIRONMENTAL HEALTH AND SAFETY
SUNY OSWEGO ENVIRONMENTAL HEALTH AND SAFETY CONTROL OF HAZARDOUS ENERGY LOCKOUT/TAGOUT PROGRAM Procedure Number EHS-LOTO-2013 Revision Number 00 Effective Date June 1, 2014 I. Purpose II. III. IV. Scope
More informationTexas Department of Insurance Division of Workers Compensation. Lockout Tagout HS96-100D (8-06)
OF OF STATE THE TEXAS TEXAS Texas Department of Insurance Division of Workers Compensation Lockout Tagout HS96-100D (8-06) Contents Purpose 1 Definitions 1-2 Responsibility 2-3 Training 3 Periodic Inspections
More information