Traffic Control Person Practice Exam #2
|
|
- Amanda Kelley
- 5 years ago
- Views:
Transcription
1 Traffic Control Person Practice Exam #2 Please read all of the questions carefully! There may be more than one correct answer. Circle the BEST answer to complete the following statements or answer the questions: Good Luck! 1. How often must a Traffic Control person re-qualify? A) Every year B) Every two years C) Every three years D) There is no requirement for TCPs to re-qualify 2. The requirements for using TCPs are found in: A) Section 18 of the OHS Regulation B) Table A of the Manual for Work on Roadways C) Section 32.7 of the Motor Vehicle Act D) None of the above 3. TCPs usually work during good weather when there is a lot of construction. 4. Symptoms of cold stress include: A) slurred speech, memory lapse and drowsiness B) hot flashes C) increased awareness D) extreme thirst 5. Traffic Control Supervisors (TCSs) are responsible for ensuring that: A) avalanche control is done correctly B) TCPs competently and safely control traffic C) Equipment Operators are trained in Traffic Control D) All of the above 6. Safety meetings must always be at the end of each shift. 7. If you are injured at work, you must report it within 3 working days.
2 8. If a worker exhibits signs or reports symptoms of heat stress or strain, the worker must be: A) given Aspirin B) given a new job C) removed from hot environment and treated by an appropriate first aid attendant, if available, or by a physician D) none of the above 9. Employers must ensure a copy of the Traffic Control Manual is available at the worksite. 10. The Motor Vehicle Act Regulations do not apply in work zones because WorkSafeBC has authority in these zones. 11. The required type of footwear for TCPs is: A) steel-toed runners B) any CSA approved boot or shoe with tor protection C) CSA approved footwear with ankle, sole, and toe protection D) Any type of footwear that provides protection from hazards 12. A traffic control person must wear retro-reflective wrist and ankle bands. 13. Common construction equipment used on public roads includes: A) tower cranes B) graders, excavators and rollers C) graders, forklifts and gantry cranes D) all of the above 14. The sign number of the Crew Working Ahead sign is C You should regularly check your headgear to make sure that: A) the liner is clean B) your name has not come off C) the brim is not sharp D) the hat has not become brittle
3 16. The emergency stop signal for equipment is: A) wave one hand back and forth over your head B) hold your arm straight up and your hand clenched in a fist C) extend both arms from the shoulder and wave them back and forth D) wave both arms from shoulder height over your head and down repeatedly 17. The buffer space is just before the transition area. 18. The purpose of the buffer space is to: A) warn motorists that workers and equipment occupy the normal traffic lanes B) close off the lane or lanes in which work is being done C) provide a space where motorists may regain control of their vehicles or stop if they fail to respond to the advanced warnings or traffic control devices in the transition area D) guide the traffic back to its normal lane 19. What is the most important consideration in a traffic control zone? A) The placement of the control zone B) The placement of the signs C) The organization of the zone D) The safety of the zone 20. What should you do if you are asked to work alone in an isolated location? A) Refuse B) Make sure your radio works C) This is a normal part of the TCP job and does not need any special procedures D) Find out who will check on you and when, what to do if checks are not made on time, and emergency rescue procedures 21. Traffic control devices must be removed when they are no longer required. 22. Who puts out the signs in the work zone and takes them in when work ends? A) Road Foreman B) Truck Driver C) Traffic Control Person / TCP Supervisor D) One of the workers
4 23. TCPs are responsible for providing: A) safety headgear, safety footwear and high visibility vests B) safety headgear, wrist bands, vests and water bottles C) radios, safety headgear and safety footwear D) clothing to protect from the elements, safety headgear and safety footwear 24. All construction equipment used on roads in BC must be bright yellow with a white retro reflective strip around the top. 25. One important consideration when directing traffic around an excavator is: A) the color of the excavator B) the type of tires C) counter weight swing area D) engine type 26. Where can a Traffic Control Person find the documentation of the distances required between signs and cones? A) Table 3c, Motor Vehicle Act B) Traffic Control Manual for Work on Roadways C) Appendix 5b, Industrial Health and Safety regulations D) From the foreman of the worksite 27. When are TCPs required to wear eye protection? A) In areas where there are flying objects or high dust levels B) Only when standing inside a work zone C) Only on gravel or newly paved road surfaces D) At all times 28. When controlling traffic during darkness TCPs must use a flashlight with a red signaling wand. 29. When deciding where to position yourself, the most important considerations are: A) the location shown in the Traffic Control Manual diagram and the road configuration B) highest visibility and your escape route C) location of the other TCP and the traffic volumes D) the location indicated in WorkSafeBC Regulation
5 30. When a violation occurs, you should: A) record as much information as you can as soon as possible B) try to find a witness of the event C) leave your position and find your supervisor D) only record information that you will not remember 31. There are 9 classifications of dangerous goods 32. A broken gas main is very hazardous because: A) there is no way of telling that a line has been broken B) the gas could cause an explosion C) a gas leak is expensive and hard on the environment D) none of the above 33. If an over-width vehicle or load approaches your work zone, you should: A) stand clear to allow it to pass B) stop the vehicle and check with the driver to ensure there is enough clearance C) call your Supervisor D) evacuate the work area 34. When using two-way radios, the Traffic Control Person should also use batons or tokens to signify the last vehicle in the line travelling through a sing lane control zone. 35. What must be done if blasting is to be done near a public roadway? A) Traffic must be detoured at least 1000 meters away B) Warning signs or a TCP must be posted to remind motorist to turn off radio transmitters and cell phones C) Motorists must turn off their engines D) An area of one quarter square kilometer must be evacuated 36. to patch a single pothole in one lane of a straight roadway with low volume traffic, where the job will take less than 15 minutes and there are no other expected problems, a TCP is required. 37. If an emergency vehicle with lights and/or siren on is approaching the site, you should: A) if safe, signal any other TCPs and immediately provide a clear path for the emergency vehicle
6 B) stop the emergency vehicle and find out what the problem is C) get off the road D) use the emergency stop signal to shut down all equipment on the worksite 38. How often should you check your traffic control devices once they are placed? A) every hour B) every shift C) every month D) as often as necessary to maintain the safety of the zone 39. The three basic road types are two-lane/two-way roads, multi-lane roads, and: A) intersection B) railway crossings C) entrance ramps D) freeways 40. Temporary traffic control devices in work zones can only be changed by: A) Police of Ministry of Transportation Officials B) Traffic Control Supervisors C) Traffic Control Supervisors and TCPs D) Equipment operators, WorkSafeBC Inspectors and TCPs Exam score: / 40 Percent (Score x 2.5) = %
TRAFFIC CONTROL PERSON TRAINING
TRAFFIC CONTROL PERSON TRAINING Refresher Self Study Guide www.bccsa.ca BC Construction Safety Alliance 2010 Table of Contents Table of Contents... 1 Introduction... 3 Traffic Control Re-Qualification...
More informationTRAFFIC CONTROL DEVICES MANUAL FOR WORK ZONES
TRAFFIC CONTROL DEVICES MANUAL FOR WORK ZONES SUMMARY Flagpersons play an important role in the high level of traffic safety expected through work zones on Saskatchewan highway projects. Flagpersons are
More informationMINNESOTA FLAGGING HANDBOOK
MINNESOTA FLAGGING HANDBOOK January, 2018 Flagging Handbook This Flagging Handbook has been developed following the guidelines of the 2011 edition of the Minnesota Manual on Uniform Traffic Control Devices,
More informationTRAFFIC ACCOMMODATION IN WORK AREAS
TRAFFIC ACCOMMODATION IN WORK AREAS TRAFFIC ACCOMMODATION IN WORK AREAS Copyright 2005 All rights reserved. Reproduction of this document in whole or in part by any means is prohibited, unless authorized
More informationSigns. signs, signals and road markings. in this chapter
3 signs, signals and road markings in this chapter Signs regulatory signs school, playground and crosswalk signs lane use signs turn control signs parking signs reserved lane signs warning signs object
More informationWork Zone Traffic Safety
Work Zone Traffic Safety Summary The Hazard: death or serious injury from being struck by vehicles or equipment in work zones. Who is at risk: streets/highways, utilities and other public works department
More informationGUIDELINES FOR EMERGENCY TRAFFIC CONTROL
GUIDELINES FOR EMERGENCY TRAFFIC CONTROL TABLE OF Contents Page Introduction...1 Chapter 6I of the 2009 MUTCD...2 Reason for Control...6 Components of Incident Management Area...7 Traffic Control Devices
More informationSTATE OF MARYLAND FLAGGER EXAM
GRADE: NAME (PRINT): ADDRESS: CITY, STATE, ZIP HOME PHONE: INSTRUCTOR: DATE: YES, I give ATSSA permission to distribute my phone number through its national flagger database, which will be accessible to
More informationWORKSITE TRAFFIC MANAGEMENT
SECTION 3 It is the intention of this section of the Fieldworkers Handbook to provide high level traffic management guidance to employees and contractors of Victorian electrical distributions companies
More informationPrinted copies of this document may not be current. Refer to SafetyNet (Domino.Doc) for the official, controlled version.
SASKPOWER TRAFFIC CONTROL PLANNING GUIDELINES INTRODUCTION page 3 DEFINITIONS page 3 PLANNING AND PREPARATION page 6 Pedestrian Safety within an Active Work Area page 7 Excavations page 8 Partial Lane
More informationSTATE OF KANSAS KDOT FLAGGER. handbook
STATE OF KANSAS KDOT FLAGGER handbook Revised in March 2008 INTRODUCTION Your job as a flagger is an important one. Your performance effects the safety of workers and those of the traveling public. Your
More informationNATIONAL FLAGGER EXAMINATION
GRADE NAME (PRINT): HOME ADDRESS: CITY/STATE/ZIP: HOME PHONE: E-MAIL ADDRESS: INSTRUCTOR: DATE: YES, I give ATSSA permission to add my phone number to the National Flagger database (flagger.com), which
More information1. What is the top priority when working on Canadian Pacific (CP) property? 2. When working on CP property what must all Contractors comply with?
1. What is the top priority when working on Canadian Pacific (CP) property? A. Production B. Safety C. Quality D. Project deadline 2. When working on CP property what must all Contractors comply with?
More informationCIRCULAR NO. O-13. Recommended Practices for Manual Protection of Highway/Railway Grade Crossings
CIRCULAR NO. O-13 Recommended Practices for Manual Protection of Highway/Railway Grade Crossings Effective: October 1, 2004 CONTENTS 1. SCOPE 2. GENERAL PRINCIPLES 3. DEFINITIONS 4. PROTECTION REQUIRED
More informationEveryday Hazards for School Bus Drivers. Reference Guide and Test
1 Everyday Hazards for School Bus Drivers Reference Guide and Test 2 Introduction One of the most important and often overlooked issues for school bus drivers is hazards. During the course of the video,
More informationEVERYONE IS A PEDESTRIAN CROSSING ADVICE FOR PEDESTRIANS
B I C Y C L I N G I N C O L O R A D O EVERYONE IS A PEDESTRIAN CROSSING ADVICE FOR PEDESTRIANS Most of us cross streets every day. We take for granted that we can cross without incident because most of
More informationPersonal Protective Equipment for Truck Drivers
High Visibility Gear: There are two categories for high visibility vests: 1 Personal Protective Equipment for Truck Drivers Workers exposed to vehicles moving in excess of 30kms (20 miles) an hour. Must
More informationTraffic Control Inspection Checklist Segment:
Traffic Control Inspection Checklist Segment: Simon Contractors Simon Contractors Originator: Description Reviewed by: Initials Date Distribution: Traffic Quality Manager, Site Assistant Traffic Manager
More informationSnohomish County Fire Chiefs Association Document #
Snohomish County Fire Chiefs Association Document # 70-03-12 Traffic Safety/Apparatus Placement Approved at General membership meeting 09/03/12 1.0 Purpose The purpose of this SOG is to establish safe
More informationTraffic Control Awareness By: Contra Costa Water District
Traffic Control Awareness By: Contra Costa Water District Dec. 2012 Work Zone Traffic Control Traffic Control Zones Traffic Control Signs How to Flag Properly Emergency Vehicles Course Outline Emergencies
More informationWork Zone Safety. Developed by HMTRI through cooperative agreement # 2 U45 ES with NIEHS
Work Zone Safety Developed by HMTRI through cooperative agreement # 2 U45 ES006177-14 with NIEHS Goal Provide you with information to keep you: Safe in the work zone. Prevent e injury and death. 2 Introduction
More informationCOVINGTON POLICE DEPARTMENT STANDARD OPERATING PROCEDURE
COVINGTON POLICE DEPARTMENT STANDARD OPERATING PROCEDURE Subject: TRAFFIC DIRECTION AND CONTROL Date of Issue: 01-01-1999 Number of Pages: 5 Policy No: P141 Review Date: 06-01-2007 Distribution: Departmental
More informationMUTCD Part 6: Temporary Traffic Control
MUTCD Part 6: Temporary Traffic Control OMUTCD English units are preferred. OHIO MANUAL OF UNIFORM TRAFFIC CONTROL DEVICES TABLE OF CONTENTS PREFACE INTRODUCTION TABLE OF CONTENTS PART 1. GENERAL Chapter
More informationCHECKLIST 5: ROADWORK TRAFFIC SCHEME AUDIT
CHECKLIST 5: ROADWORK TRAFFIC SCHEME AUDIT 5.1 General items 5.1.1 Alignment Are the roadworks located safely with respect to horizontal and vertical alignment? If not, does works signing cater for this?
More informationGUIDELINE: Roadside Worksites
Title: GUIDELINE: Roadside Worksites Version 1.0 Short description Relevant to Authority Responsible officer Responsible office A guideline on ensuring a safe method of works on or near roadways within
More informationOn-Road Skills Demonstration
TRAINING TOOL On-Road Skills Demonstration DRIVING THE FUTURE 2 ON-ROAD SKILLS DEMONSTRATION TRAINING TOOL On-Road Skills Demonstration This document is a resource for consistent and objective evaluation
More informationSECTION TRAFFIC REGULATIONS
SECTION 01550 TRAFFIC REGULATIONS PART 1 - GENERAL 1.01 OBJECTIVES A. The Contractor shall provide for safe movement of vehicular, bicycle and pedestrian traffic, including persons with disabilities in
More informationCHAPTER 1 STANDARD PRACTICES
CHAPTER 1 STANDARD PRACTICES OBJECTIVES 1) Functions and Limitations 2) Standardization of Application 3) Materials 4) Colors 5) Widths and Patterns of Longitudinal Pavement Marking Lines 6) General Principles
More informationDriver Education Ch. 4: Safe Driving Rules & Regulations. Ms. Marx
Driver Education Ch. 4: Safe Driving Rules & Regulations Ms. Marx Speed Control Speed is one of the most common contributing factors of fatal & other types of accidents School zones, business or residential
More informationLives, including yours, could depend on it! Name
Remember that you play a vital part in keeping the public and your co-workers safe. If you are unsure of any flagging procedure, ask your supervisor for further explanation. Lives, including yours, could
More informationSafety Orientation OSHA 5(a)(1) General Duty Clause SAFETY ORIENTATION OSHA Section 5(a)(1) PURPOSE SCOPE
SAFETY ORIENTATION OSHA Section 5(a)(1) PURPOSE Preventing injuries in the workplace is a primary consideration for Millard. An orientation program has been developed to introduce employees to the warehousing
More informationGuide for Law Enforcement Personnel in Work Zones
Guide for Law Enforcement Personnel in Work Zones Table of Contents Introduction........................... 3 Roles and Responsibilities................ 5 Most Common Law Enforcement Services in Work
More informationMUNICIPALITY OF ANCHORAGE TRAFFIC CODE UPDATE MASTER RECOMMENDATION REPORT: 9.14, 9.16, 9.18
MUNICIPALITY OF ANCHORAGE TRAFFIC CODE UPDATE MASTER RECOMMENDATION REPORT: 9.14, 9.16, 9.18 Report Date: Please send all recommendations for update to Shane Locke (343-8413, lockesr@muni.org) 8-Apr-09
More informationFL AGGER S HANDBOOK January 2012
FLAGGER S HANDBOOK January 2012 Introduction You have been chosen to be a flagger because your supervisor feels you are physically able, mentally alert and sufficiently commanding in appearance to properly
More informationMinimum Safety Requirements for Contractors Working on Railway Property
Minimum Safety Requirements for Contractors Working on Railway Property Effective_ April 1, 2007 Introduction Canadian Pacific is committed to provide a Safe and Healthy working environment for all Railway
More informationREVISION 2 VIRGINIA WORK AREA PROTECTION MANUAL. Ginger Quinn & Paul Kelley April 11, 2018
REVISION 2 VIRGINIA WORK AREA PROTECTION MANUAL Ginger Quinn & Paul Kelley April 11, 2018 ADA & District Traffic Engineer Added in various sections Work Zone Pedestrian and Bicycle Guidance document VDOT
More informationAppendix A Guiding Principles for Cycling Safety in Work Zones
Appendix A Guiding Principles for Cycling Safety in Work Zones 1. Identify Existing Cycling Facility and Requirements This step should be part of the permitting/approval processes for construction zones
More informationDeveloped by: The American Traffic Safety Services Association (ATSSA) 15 Riverside Parkway, Suite 100 Fredericksburg, VA
Addendum Developed by: The American Traffic Safety Services Association (ATSSA) 15 Riverside Parkway, Suite 100 Fredericksburg, VA 22406-1022 800-272-8772 This material is based upon work supported by
More informationFlorida Class E Knowledge Exam Road Rules Practice Questions
1. If you are being followed too closely while driving, you should: A. Drive closer to the car in front of you. B. Speed up to increase the distance between you and the following vehicle. C. Slow down
More informationEmergency Roadside Technician Dies When Struck by a Single-Unit Truck on an Interstate Shoulder. Incident Number: 05KY001
Emergency Roadside Technician Dies When Struck by a Single-Unit Truck on an Interstate Shoulder Incident Number: 05KY001 Location on bridge where responder attempted to avoid semi. Kentucky Fatality Assessment
More informationHomework Module 7.01 Drivers Manual Study Questions
Homework Module 7.01 Drivers Manual Study Questions Name: Date: Directions: Use the Oregon Driver Manual to answer each of the following questions. It is suggested that you underline or highlight each
More informationCHAPTER 3 SIGNS, SIGNALS AND PAVEMENT MARKINGS. Responsible Driving (Red book) NOTES & STUDY GUIDE
CHAPTER 3 SIGNS, SIGNALS AND PAVEMENT MARKINGS Responsible Driving (Red book) NOTES & STUDY GUIDE Regulatory Signs Warning Signs International Signs Guide Signs Types of Road Signs Sub category (construction
More informationIdentify the letter of the choice that best completes the statement or answers the question.
Chapter 02 - Practice Questions Multiple Choice Identify the letter of the choice that best completes the statement or answers the question. 1) No-parking zones often are near a. fire hydrants, curves,
More informationBicyclist Signing Guidelines
Bicyclist Signing Guidelines April, 2009 1 Introduction This paper describes the Montana Department of Transportation s (MDT) current practices related to bicyclist safety and signing issues and presents
More informationRoad Traffic Signs in Germany
Warning signs Road Traffic Signs in Germany General danger Curve left Curve right Double curve Double curve Accident hazard Sliding danger Winter sports along road Soft shoulder Rough road edge Steep upgrade
More informationHEAT ILLNESS PREVENTION PLAN (HIPP) FOR. PAR Electrical Contractors Inc.
HEAT ILLNESS PREVENTION PLAN (HIPP) FOR PAR Electrical Contractors Inc. Employer Name: PAR Electrical Contractors Inc. Address: 1465 W. 4 th St., Reno, NV 89503 Revised: December 18, 2013 1 Heat Illness
More informationCh Driving on Expressways. Characteristics of Expressway Driving. Expressway. Types of Expressways. Why do they have fewer collisions?
Ch 11 Driving on Expressways 11.1 Characteristics of Expressway Driving Expressway Is a limited-access or controlled-access highway. Types of Expressways Interstate highways Freeways Parkways * Most of
More informationDEFINITIONS Activity Area - Advance Warning Area Advance Warning Sign Spacing Advisory Speed Approach Sight Distance Attended Work Space
DEFINITIONS Activity Area - that part of a TTC zone activity area where the work actually takes place. It consists of the work space, traffic space and one or more buffer spaces. Advance Warning Area -
More informationTraffic Signs and Markings. Instructor: Dr. Yahya Sarraj Associate Prof. Of Transportation
and Markings Instructor: Dr. Yahya Sarraj Associate Prof. Of Transportation Definition; A traffic sign is defined as a device mounted on a fixed or portable support whereby a specific message is conveyed
More informationRoad Usage Permit Application Form
15/06/2012 Road Usage Permit Application Form City Yards 1495 Hardy Street Kelowna, BC V1Y 7W9 Tel: (250) 469-8600 Fax: (250) 862-3330 PERMITS WILL BE APPROVED OR DECLINED WITHIN 5 BUSINESS DAYS. WORK
More informationTRAFFIC CONTROLLERS' HANDBOOK
TRAFFIC CONTROLLERS' HANDBOOK SIXTH EDITION 2010 MAIN ROADS WESTERN AUSTRALIA Produced by Main Roads Western Australia Acknowledgement: Main Roads Western Australia wishes to acknowledge the publication
More informationSpeed Control & Limits
Speed Control & Limits Exceeding the speed limit is a common contributing factor of fatal and other types of accidents. *25 mph* School zones, business or residential districts *55 mph* Certain state highways
More informationSafe Operating Procedure Site Safety Orientation and Agreement
- VLF Site Safety Orientation Title: Site Safety Orientation Site: Vancouver Landfill Last Revision: June 2016 The, Transfer & Landfill Operations Branch requires that all persons working on the Vancouver
More informationNew Trends In Temporary Traffic Control (TTC) Spring Occupational Safety & Health Committee Conference Philadelphia, PA
New Trends In Temporary Traffic Control (TTC) Spring Occupational Safety & Health Committee Conference Philadelphia, PA Michael Kelly Work history - Fire service member of 30 years (retired at the rank
More informationSign Designs and Markings Manual (TEM 295-2) Page 8-3
Sign Designs and Markings Manual (TEM 295-2) Page 8-3 TEMPORARY TRAFFIC CONTROL SIGNS INDEX Regulatory Signs R1-1 STOP R1-2 YIELD R1-2a TO ONCOMING TRAFFIC R2-1 SPEED LIMIT R2-H2a VEHICLES OVER 4 TONS
More informationSTREET and UTILITY REPAIRS WORK AREA PROTECTION GUIDE
STREET and UTILITY REPAIRS WORK AREA PROTECTION GUIDE May 2006 Street and Utility Repairs Work Area Protection Guide TABLE OF CONTENTS 1. Introduction... 1 2. Typical Applications... 11 2.1 Use of Hand-Signaling
More informationMUTCD Part 6G: Type of Temporary Traffic Control Zone Activities
MUTCD Part 6G: Type of Temporary Traffic Control Zone Activities 6G.01 Typical Applications Each temporary traffic control (TTC) zone is different. Many variables, such as location of work, highway type,
More informationAppendix Work Zone Traffic Control
ppendix Work Zone Traffic Control The purpose of this appendix is to present basic guidelines for work zone traffic control and to supplement the Highway Work Zone Safety Checklist. This appendix presents
More informationTemporary Traffic Control for Highway Work Zones
Temporary Traffic Control for Highway Work Zones MONTHLY DELMARVA MISS UTILITY MEMBER MEETING MARCH 20, 2014 PRESENTED BY: Adam Weiser, P.E. PTOE Safety Programs Manager Delaware Department of Transportation
More informationTraffic Signs and Signals
CHAPTER FOUR Traffic Signs and Signals Traffic signs control traffic flow, making streets and highways safer for drivers, bicyclists and pedestrians. These signs, which are posted by the Indiana Department
More informationTraffic Management Guidelines for Structure Rehabilitation Projects
, Traffic Management Guidelines for Structure Rehabilitation Projects February 2009 1 Purpose & Background These guidelines were prepared in order to assist the Regional Structural Office in determining
More informationAdult School Crossing Guard Guidelines
The Role of the Adult school crossing guards play an important role in the lives of children who walk or bicycle to school. They help children safely cross the street at key locations. They also remind
More information2017 Temporary traffic control guidelines for pedestrians. v.2
2017 Temporary traffic control guidelines for pedestrians v.2 Temporary Traffic Control Guidelines for Pedestrians (2017) The safety and mobility of pedestrians, cyclists and motorists must be considered
More informationCHAPTER 6H. TYPICAL APPLICATIONS
Section 6H.01 Typical Applications Support: CHAPTER 6H. TYPICAL APPLICATIONS Chapter 6G contains discussions of typical temporary traffic control activities. Chapter 6H presents typical applications for
More informationHow severely could the risk hurt someone?
Safe Work Method Statement No: WMS-08 Task: Install Drainage This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia) Pty Ltd Authorised
More informationCHAPTER 6H. TYPICAL APPLICATIONS
2006 Edition Page 6H-1 CHAPTER 6H. TYPICAL APPLICATIONS Section 6H.01 Typical Applications Support: Whenever the acronym TTC is used in this Chapter, it refers to temporary traffic control. Standard: The
More informationSafe Working On Roads Standard Operating Procedures
Safe Working On Roads Standard Operating Procedures Operational Management Procedures Page 1 of 15 Safe Working on Roads SOPs Prepared by State Operations NSW Rural Fire Service 15 Carter Street, Lidcombe
More informationADJUSTING TO, FOLLOWING, AND MEETING URBAN TRAFFIC
Lesson 4 Student Notes 1 ADJUSTING TO, FOLLOWING, AND MEETING URBAN TRAFFIC 1. What two main factors make city driving difficult? There are more cars, buses, trucks, and pedestrians per mile. City hazards
More informationCW20-1D 48" X 48" (Flags- See note 1) G " X 24" (See note 2)
CK: DW: CK: x for mph or less mph devices may be omitted if the work area is a minimum of from the nearest traveled way. (See notes 4 & 5) x for mph or less Work Space mph x for mph or less mph (See notes
More informationWORK ZONE TRAFFIC CONTROL PROCEDURES
WORK ZONE SETUP / REMOVAL WORK ZONE TRAFFIC CONTROL PROCEDURES When installing a work zone, install the advance warning signs on all approaches prior to installing the traffic control devices. Perform
More informationCycle Track Design Best Practices Cycle Track Sections
Design Best Practices Sections It is along street segments where the separation and protection methods of cycle tracks offer more comfort than conventional bicycle lanes, and are more attractive to a wide
More informationBES Line guard Handbook INTRODUCTION
BES Line guard Handbook INTRODUCTION This manual is provided to offer direction in the City of Bloomer for training adult crossing guards in their best responsibilities at crosswalk where students generally
More informationTRAFFIC CONTROL DEVICES MANUAL FOR WORK ZONES
TRAFFIC CONTROL DEVICES MANUAL FOR WORK ZONES APPLICATION Delineation devices are used to warn and alert motorists of hazards created by work activities in or near the travelled way and to guide and direct
More informationUnit Six: Driving Faster with More Risk URBAN, SUBURBAN, AND RURAL DRIVING
Unit Six: Driving Faster with More Risk URBAN, SUBURBAN, AND RURAL DRIVING What Is The Impact Of Distraction? Objectives For Unit Six Students will be able to describe the skills necessary to What safely
More informationHome Link Assignment # 1 - SIGNS
Home Link Assignment # 1 - SIGNS 1 A. Road slippery when wet B. Hidden intersection ahead C. Narrow road ahead D. Winding road ahead 2 A. Slow moving vehicle ahead B. Head end street ahead C. Yield right-of-way
More informationPlan prepared for: Brennan Paving and Construction. Plan prepared by: Direct Traffic Management
Traffic Control Plan Hwy 401 - Bridgeland Avenue / Site 37-283 Grading, Drainage, Garnular Base, Hot Mix Paving, Electrical, Structural and Plan prepared for: Plan prepared by: General Notes WB 401 Collector
More informationWork Zone Safety in Oregon
Work Zone Safety in Oregon Nature of the Problem National studies show Driver Inattention is the biggest contributor to work zone crashes. Driving too fast for conditions or Speed is another significant
More informationGuidance. ATTACHMENT F: Draft Additional Pages for Bicycle Facility Design Toolkit Separated Bike Lanes: Two-Way to One-Way Transitions
ATTACHMENT F: Draft Additional Pages for Bicycle Facility Design Toolkit Separated Bike Lanes: Two-Way to One-Way Transitions This treatment provides a transition from two-way separated bike lanes to one-way
More informationIncluding Revision 1 dated May 2012 and Revision 2 dated May 2012
Including Revision 1 dated May 2012 and Revision 2 dated May 2012 Page 634 2009 Edition Notes for Figure 6H-1 Typical pplication 1 Work eyond the Shoulder 1. If the work space is in the median of a divided
More informationHow severely could the risk hurt someone? Low/Insignificant First aid
Safe Work Method Statement No: WMS-02 Task: Concreting, Formwork and Steel Fixing This WMS is submitted to: Project name and site address: Contact: Preparation of WMS by: Robert Raams Company: Enwon (Australia)
More informationChapter #4 Traffic Control Devices and Laws
Chapter #4 Traffic Control Devices and Laws Chapter #4 Overview Unit 4 will introduce the student to traffic control devices, including signs, signals and pavement markings, as well as traffic laws specific
More informationEMPLOYER SAMPLE PROCEDURES FOR HEAT ILLNESS PREVENTION August 2011
EMPLOYER SAMPLE PROCEDURES FOR HEAT ILLNESS PREVENTION August 2011 California employers with any outdoor places of employment must comply with the Heat Illness Prevention Standard T8 CCR 3395. These procedures
More informationWORK ZONE TRAFFIC CONTROL & SAFETY
WORK ZONE TRAFFIC CONTROL & SAFETY Purpose of Temporary Traffic Control 1. Warn motorists and pedestrians of hazards. 2. Advise proper travel path. 3. Delineate areas not to be used. 4. Separate the travel
More informationDrivers accounted for 77% of compensable claims and had the highest median medical costs ($8,444) for fall on the same level.
couriers and Messengers 80 2006-2012 Overview 591 compensable claims Costs $19.5 million Over 114,000 days of lost time A compensable rate of 4.1 per 100 FTE or 1 in 25 employees Figure 61. Compensable
More informationCHAPTER 2G. PREFERENTIAL AND MANAGED LANE SIGNS
2011 Edition - Revision 2 Page 275 Section 2G.01 Scope CHAPTER 2G. PREFERENTIAL AND MANAGED LANE SIGNS 01 Preferential lanes are lanes designated for special traffic uses such as high-occupancy vehicles
More informationIllini Union Champaign, IL. February 24, Paul Lorton, P.E. Safety Programs Unit Chief IDOT, Division of Highways, Bureau of Safety Engineering
Illini Union Champaign, IL February 24, 2015 Paul Lorton, P.E. Safety Programs Unit Chief IDOT, Division of Highways, Bureau of Safety Engineering Temporary Concrete Barrier Pinning and Drop-off Policy
More informationlaws AnD rules of the road ight-of-way rules General Information Respect Respecting respect Pedestrians Important:
LAWS AND RULES OF THE ROAD Right-of-Way Rules General Information Right-of-way rules, together with courtesy and common sense, help to promote traffic safety. It is important to respect the right-of-way
More informationVermont Permit Test Flash Cards
Vermont Permit Test Flash Cards Study online at quizlet.com/_aormb are the most likely places for car and motorcycle collisions to occur. intersections are areas around trucks where cars disappear 2. :
More informationCalifornia DMV Test. Mark the correct answers. 1. The intersection has a stop sign. Where should you first stop?
California DMV Test Mark the correct answers 1. The intersection has a stop sign. Where should you first stop? At the crosswalk or limit line. After the crosswalk. Out far enough to see cross traffic.
More informationCARE AND VIGILANCE SAVE LIVES!
CARE AND VIGILANCE SAVE LIVES! PEDESTRIAN, Be Safety Conscious! Each day, approximately ten pedestrians are involved in traffic accidents throughout Québec. If you use the province s road network on foot,
More informationFLYING OBJECTS MANUAL HANDLING EXCESSIVE NOISE
JOB NO: PROJECT: DATE: SWMS NO: SWMS 002 PREPARED BY: Ian Hartley REVISED BY: Nick Bragg & Cameron McNeil ACTIVITY: STUMP REMOVAL SUPERVISED BY: REVISION DATE: April 2016 MINIMUM PERSONAL PROTECTIVE EQUIPMENT
More informationIdentify the letter of the choice that best completes the statement or answers the question.
Chapter 10 - Practice Questions Multiple Choice Identify the letter of the choice that best completes the statement or answers the question. 1) Before passing a vehicle in your lane, a. anticipate the
More informationMUTCD Part 6D: Pedestrian and Worker Safety
MUTCD Part 6D: Pedestrian and Worker Safety Section 6D.01 Pedestrian and Worker Safety The needs and control of all road users (motorists, bicyclists, and pedestrians) within the highway, including persons
More informationA TRAFFIC PLAN TO LIVE BY. Basic Worker Safety WORKER SAFETY. Developed by: American Traffic Safety Services Association
Basic Worker Safety Developed by: American Traffic Safety Services Association Traffic Control in Work Zones Temporary Constantly changing Not well liked by motorists Unexpected by the road users Workers
More information2017 Changes to the 2011 MMUTCD January 2017
2017 Changes to the 2011 MMUTCD January 2017 The design for the Weight Limit symbol sign (R12-5) has been modified to show a threeunit vehicle as the third line of the regulatory weight limit sign. This
More informationTRAFFIC ACCIDENT STUDY GUIDE 2003
TRAFFIC ACCIDENT STUDY GUIDE 2003 SECTION 5 This study guide is designed to provide the law enforcement Explorer with basic principles. The guide is not all inclusive, and does not delineate specific techniques
More informationWork Area Traffic Control Policies and Procedures
Work Area Traffic Control Policies and Procedures August 2016 Traffic Operations 626 Linden Street P.O. Box 580 TABLE OF CONTENTS Introduction... 1 Applicability... 1 Goals... 1 Authority... 2 Planning...
More informationLearn these 10 basic cycling hand signals to keep you and those around you safe out on the road.
NMTS Bike Hand Signals Learn these 10 basic cycling hand signals to keep you and those around you safe out on the road. 1. Stop signal The hand signal you use for stopping will most likely depend on the
More informationAppendix C. TRAFFIC CALMING PROGRAM TOOLBOX
Appendix C. TRAFFIC CALMING PROGRAM TOOLBOX PHASE I...2 Do Not Enter Sign...3 One-Way Sign...4 Turn Prohibition...5 Pavement Markings...6 Speed Monitoring Trailer...7 Neighborhood Speed Watch...8 Police
More informationBeginning School Bus Driver Curriculum UNIT IX. FIELD TRIPS and TRAFFIC CONTROL DEVICES. Revised 09/2011 Revised 10/2013 (Instructional Content)
Beginning School Bus Driver Curriculum UNIT IX FIELD TRIPS and TRAFFIC CONTROL DEVICES Revised 09/2011 Revised 10/2013 (Instructional Content) Unit IX FIELD TRIPS AND TRAFFIC CONTROL DEVICES TABLE OF CONTENTS
More information