NESC WORKSHOP Revisions to Part 4 (Work Rules) Sam Stonerock. October 18, 2016
|
|
- Miranda Sutton
- 5 years ago
- Views:
Transcription
1 NESC WORKSHOP 2017 Revisions to Part 4 (Work Rules) Sam Stonerock October 18, 2016
2 Work Rules for the Operation of Electric Supply and Communications Lines and Equipment 2017 edition Reconcile existing rules with FED-OSHA revisions Rule on electric arc exposures / protection - New information addressing hand, head, feet protection - New information for dc systems - New information on 480V arc-in-a-box test results Rule 420K on fall protection - Fall protection to be used at elevated locations above 4 ft. - Appropriate equipment to limit free fall to 2 ft. - Anchorages must support 3000 lb-force - Employees to visually assess anchorages 2
3 Work Rules for the Operation of Electric Supply and Communications Lines and Equipment 2017 edition (continued) Minimum Approach Distances (MAD) - Revise Table (Communication) - Revise Rule Adds rule specific definition for reach / extended reach - Revise rules for voltages above 72.5kV - Revise default Table (Supply) - Add new Tables 441-2, 441-3, ( T has been calc d) - Retain/renumber existing Tables 441-2, 441-3, Minimum clearances for open air gap - New Table for supply stations and OH lines 3
4 Rule 410A3 New / Revised Exceptions EXCEPTION 2: Arc-rated equipment is not necessary for the employee s hands when the employee is wearing rubber insulating gloves with protectors. Heavy-duty leather work gloves with a weight of at least 407 gm/m2 (12 oz/yd2) may be worn if the estimated incident energy is no more than 14 cal/cm2. EXCEPTION 3: Arc-rated equipment is not necessary for the employee s feet when the employee is wearing heavy-duty work shoes or boots. 4
5 Rule 410A3 New / Revised Exceptions EXCEPTION 4: Arc-rated equipment is not necessary for the employee s head or face when the employee is wearing head protection meeting 29 CFR if the estimated incident energy is less than OSHA 9 cal/cm2 for exposures involving single phase arcs in open air less than or 5 cal/cm2 for other exposures. Arc-rated equipment is necessary for the protection of the employee s head and face and may consist of head protection meeting OSHA 29 CFR and a face shield with a minimum arc rating of 8 cal/cm2 if the estimated incidentenergy exposure is greater than 9 cal/cm2 and less than 13 cal/cm2 for exposures involving single-phase arcs in open air or greater than 5 cal/cm2 and less than 13 cal/cm2 for exposures involving single-phase arcs in open air or greater than 5 cal/cm2 and less than 9 cal/cm2 for other exposures. For exposures involving single phase arcs in open air, the arc rating for the employee s head and face protection may be 4 cal/cm2 less than the estimated incident energy. 5
6 New Rule 410A6 / Revised Rule 420Q Antennas 410A6 The employer shall provide training to all employees who work in the vicinity of antennas operating in the range of 3 khz to 300 GHz to recognize and mitigate exposure to radiofrequency sources that exceed exposure levels set forth by the regulatory authority having jurisdiction. NOTE: See OSHA 29 CFR , Subpart G [B67]; OSHA 29 CFR , Subpart R [B68]; FCC Bulletin No. 65 [B32]; IEEE Std C [B61]. 420Q Employees working in the vicinity of antennas operating in the range of 3 khz to 300 GHz shall use controls to mitigate exposure to radio-frequency sources that exceeds permissible exposure levels. NOTE: See Rule 410A6. 6
7 Rule 420K (Fall Protection) 1. Employees shall use appropriate fall protection equipment while climbing, transferring, or transitioning across obstacles on poles or structures, unless doing so not feasible or creates a greater hazard than doing so unattached. a. When work positioning is used, it shall be rigged in a manner in which the employee cannot free fall more than 0.60 m (2 ft). b. Anchorages for work-positioning equipment shall be capable of supporting at least twice the potential impact load of an employee s fall, or 13.3 kn (3000 lb-force), whichever is greater. 7
8 Rule 420K (continued) NOTE 1: Wood-pole fall-restriction devices meeting American Society of Testing and Materials Standard Specifications for Personal Climbing Equipment, ASTM F [Bx] or later versions, are deemed to meet the anchorage-strength requirement when they are used in accordance with manufacturers instructions. NOTE 2: Recognized and generally accepted good engineering practices, with consideration given to such factors as design specifications and maintenance procedures, may be used in determining whether potential anchorages meet the strength requirements in 420K1b provided the employee performs a visual inspection before use that reveals nothing about the appearance of the anchorage (for example, corrosion around support-member connections or bent support members) suggests that the applicable strength criteria would not be met. NOTE 3: On poles, when the employee is transitioning or at the work location and the work positioning strap is positioned above a bolted attachment, step bolt, or other equipment, these attachments may serve as the anchorage. It is not necessary to determine the strength of the attachment provided the employee performs a visual inspection before use that reveals nothing about the appearance of the anchorage (for example, corrosion or cracks) suggests that the applicable strength criteria would not be met. 8
9 Rule 431 / Table
10 Rule A1a A. Minimum approach distance to energized lines or parts 1. General Employees shall not approach or bring any conductive object within the minimum approach distance listed in Table or Table or distances as determined by an engineering analysis to exposed energized lines or parts unless one of the following is met: a. The line or part is de-energized and grounded per Rule 444D. EXCEPTION: For voltages less than 600 V where the making of the ground is impractical, the line or part may be isolated in lieu of installing temporary protective grounds provided the following conditions are met: (a) the lines and equipment are isolated from all sources and tested to be de-energized, (b) there is no possibility of contact with another energized source, and (c) the hazard of induced voltage is not present. 10
11 Rule A1d d. The employee is performing barehand live-line work according to Rule 446. NOTE 1: Minimum approach distances calculated under this rule for kv to kv contain the electrical component plus 0.31 m (1 ft) for inadvertent movement. Voltages kv to 72.5 kv contain the electrical component plus 0.61 m (2 ft) for inadvertent movement. Voltages above 72.5 kv contain the electrical component plus 0.31 m (1 ft) for inadvertent movement. NOTE 2: Methodology for calculating minimum approach distances were taken from 29 CFR Appendix B [B66]. NOTE 3: The voltage ranges are contained in ANSI C , Table 1. NOTE 4: For the purpose of Section 44, reach is defined as the range of anticipated motion of an employee while performing a task, and extended reach is defined as the range of anticipated motion of a conductive object being held by an employee while performing a task. 11
12 Rule 441 (Tables) 441A4 When performing live line work, employees shall position themselves so that they are not within the reach or extended reach of the applicable minimum approach distance. In lieu of using the minimum approach distances in Table 441-1, the minimum approach distance in Table through Table may be used provided the per unit transient overvoltage value (T) has been determined through an engineering analysis considering the system design, expected operating conditions, and control measures. NOTE 1: Control measures include blocking reclosing, prohibiting switching during live line work, using protective air gaps, use of closing resistors and surge arrestors, etc. NOTE 2: IEEE Std [B37] and OSHA 29 CFR Appendix B [B66] contain information that may be used to perform an engineering analysis to determine maximum transient overvoltage factors. The engineering analysis may be performed on a system basis or a per-line basis. 12
13 13
14 14
15 15
16 16
17 Rule 444 / New Table
18 Subcommittee 8 Working Group(s) / 2022 Code Cycle Working Group 8.14 Part 4 Generation Facilities Working Group 8.14 was formed to address possible gaps in Part 4 rules regarding significance to work in generating stations. The kick-off meeting for this WG was held in late August to perform a thorough review of existing rules specifically to assess their relevance to that work. Additionally, a former member of Subcommittee developed a draft Part 5, designed to specifically address work in generating stations. Also, the intent is to deliver the WG s new/revised draft rules to the full Subcommittee for consideration as new (SC8) Change Proposal(s) Working Group 8.XX Part 4 / Part 1 Storage batteries Working Group 8.XX Part 4 / Table Working Group 8.XX Part 4 / New Medium Voltage Arc Flash Table 18
KMU SUBSTATION WORKSHOP
Rick Aguilar, Director of Job Training & Safety KMU SUBSTATION WORKSHOP JUNE 29-30, 2016 OTTAWA, KS Hazards & Safety Rules Qualified Personnel & Task-Based Hazard Mitigation Worksite Applications & Considerations
More informationMinimum Approach Distances (MAD)
Minimum Approach Distances (MAD) The final rule updated OSHA s default values for transient over voltages (TOV), selecting far more conservative values. As TOV is one of the major factors for calculating
More informationJanuary 10, EEI OSHA Team
January 10, 2017 TO: FROM: Re: EEI Occupational Safety & Health Executive Committee EEI Occupational Safety & Health Committee EEI Industrial Hygiene Subcommittee EEI Regulatory Review Task Force EEI OSHA
More informationARC FLASH HAZARD ANALYSIS
I. ARC FLASH HAZARD ANALYSIS IS REQUIRED ARC FLASH HAZARD ANALYSIS By Mike Lang Principal Field Engineer OSHA s 29 CFR Part 1910.132(d) states: The employer shall assess the workplace to determine if hazards
More informationElectrical Safety Program
Electrical Safety Program For Adopted LC-1005 Rev. 06/16 Page 1 I. Introduction As part of Organization s overall safety and health program, an
More informationNECA Personal Protective Equipment (PPE) Selector
NECA Personal Protective Equipment (PPE) Selector Objectives Explain why electrical contractors should follow the precautions set forth in NFPA 70E List the hazards which demonstrate why an arc flash risk
More informationPOWER PLANT RELAY REPLACEMENT DELIVERABLE ARC FLASH
POWER PLANT RELAY REPLACEMENT DELIVERABLE ARC FLASH ISU Senior Design Group: Dec15-22 Dan Dye Project Web Site: http://dec1522.sd.ece.iastate.edu/ Project Sponsor: CIPCO Project Advisor: Professor Mani
More informationSelection of Electrical PPE Tables
Selection of Electrical PPE Tables Instructions Table 1 - Starting with Table 1, select the task you plan to do (right-hand column) and the condition of the equipment you will be working on, (center column).
More informationAppendix A: Energized Work Permit
Appendix A: Energized Work Permit Part I: To be completed by the Supervisor Description of Circuit & Equipment: Job Location: Description of Work to Be Done: Justification of why the circuit cannot be
More informationOriginal Date of Issue: 04/09
POLICIES AND PROCEDURES DEPARTMENT: Environmental Health and Safety SUBJECT: Electrical Safety Program Original Date of Issue: 04/09 Reviewed 12/2011 Revised 12/2011 BACKGROUND ELECTRIC SHOCK It is well
More informationHealth & Safety Policy and Procedures Manual SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY
SECTION 6 ELECTRICAL SAFETY / CONTROL OF HAZARDOUS ENERGY 1. CONTROL OF HAZARDOUS ENERGY POLICY AND PROCEDURES A. OSHA References: 29 CFR 1910.147, 29 CFR 1910.332, 29 CFR 1910.333, 29 CFR 1926.417 B.
More informationArc Flash. Safety 21
Arc Flash Safety 21 Arc Flash Introduction Electrical Hazards Safety Planning De-Energizing Equipment Working Hot Summary Introduction Most people don t think about electricity very much, which is surprising
More informationElectrical Hazard Assessments: OSHA & The NFPA 70E?
Electrical Hazard Assessments: OSHA & The NFPA 70E? AWEA Health & Safety Mike Moore Key Learning Objectives Key Learning's Statistical Electrical Incidents & Injuries What Does OSHA Want? A quick Glimpse
More informationarc flash hazard analysis
arc flash hazard analysis arc flash note 3 By mike lang, principal field engineer Arc Flash Hazard Analysis is Required OSHA s 29 CFR Part 1910.132(d) states: The employer shall assess the workplace to
More informationELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR CFR , ,
ELECTRICAL (COMPREHENSIVE) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.331 335-29 CFR 1926.302, 1926.416, 1926.417 BASIS: The National Safety Council estimates that there are at least 300 deaths
More informationElectrical Safety Program
Electrical Safety Program The University Of Iowa Environmental Health & Safety 122 Grand Avenue Court Iowa City, IA 52242-1000 Phone: 319-335-8501 Date Revised/Reviewed: 6/8/2018 Table of Contents 1. Summary...
More informationWhy do I need to do an Arc-Flash Analysis?
Why do I need to do an Arc-Flash Analysis? Presented By Tom Norwood for Alexander Nizov, P.E. Principal/Manager Electrical Engineering Division TRAINING INSTITUTE, INC. A SUBSIDIARY OF MEGGER Hazards Analysis
More informationPOWER DELIVERY. Contractor Health & Safety General Terms and Conditions. Appendix B Personal Protective Equipment
Personal Protective Equipment ( PPE ): All PPE worn on IPL job sites must have ANSI and/or approval ratings. Hard hats and safety glasses with side shields (including prescription eyewear) shall be worn
More informationCITY AND COUNTY OF DENVER CR&CF RISK UNIT Electrical Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.3 Electrical Safety Standard 1.0 Introduction 2.0 Scope The purpose of this standard is to establish safe work practices that are intended to prevent electric
More informationENVIRONMENTAL HEALTH AND SAFETY PERSONAL PROTECTIVE EQUIPMENT
ENVIRONMENTAL HEALTH AND SAFETY PERSONAL PROTECTIVE EQUIPMENT PERSONAL PROTECTIVE EQUIPMENT Table of Contents A. Scope... 1 B. General Requirements... 1 C. Responsibility... 1 1. Supervisor... 1 2. Department
More informationUser Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More information70e Training - Electrical Safety in the Workplace
70e Training - Electrical Safety in the Workplace Contact us Today for a FREE quotation to deliver this course at your company?s location. https://www.electricityforum.com/onsite-training-rfq This NFPA
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More information2018 NFPA 70E Electrical Safe work practices
This course provides a thorough knowledge of the dangers and recommended safe behaviors for those who work daily around electrical hazards. This course goes into examples of real life application to give
More information: Electric Power Generation, Transmission, and Distribution. Region IV - OSHA
1910.269: Electric Power Generation, Transmission, and Distribution Region IV - OSHA Scope This standard covers the operation and maintenance of electric power generation, control, transformation transmission,
More informationManagement Plan for Electrical Safety ISD #535
Management Plan for Electrical Safety ISD #535 Health & Safety Office Maintenance Service Building 10 SE 9 ½ Street Rochester, MN 55904 507-328-4507 MANAGEMENT PLAN FOR ELECTRICAL SAFETY Table of Contents
More informationto the 2009 Edition Standards & Codes Introduction Background Byron Jordan Sr. Field Engineer
Critical Changes to the NFPA 70E Standard Standards & Codes Note 2 Byron Jordan Sr. Field Engineer Introduction Since its inception in 1979, NFPA 70E: Standards for Electrical Safety in the Workplace has
More informationUser Instructions 1790 Rail Anchor
User Instructions 1790 Rail Anchor This document is intended to meet the Manufacturer s Instruction requirements as stated by ANSI Z359.1, and should be used as part of an employee training program as
More informationElectrical Safety For Managers Updated For E. ElectricalTrainingPro.com
Electrical Safety For Managers Updated For 2018 70E Daryn Lewellyn daryn@electricaltrainingpro.com ElectricalTrainingPro.com 877.393.9901 1 Fatalities From Exposure To Electricity 1992-334 Bureau of Labor
More informationELECTRIC OPERATING PROCEDURES Date: 11/01/06
Doc No.: NG-USA EOP D001 Page: 1 of 5 ELECTRIC OPERATING PROCEDURES SUBJECT: Cutouts Open/Enclosed Type SECTION: Distribution/Overhead REFERENCE: National Grid Retail Company Safety Manuals National Grid
More informationMISSOURI UNIVERSITY OF SCIENCE & TECHNOLOGY Procedure: 3.6
Procedure This electrical safety procedure structures safety procedures to meet the requirements of the NFPA-70E Standard. The program is designed for qualified employees who occasionally must perform
More informationUSER INSTRUCTIONS LARGE HOOK & STRAP ANCHORAGE CONNECTOR ! WARNING
ROSE MODEL NUMBER USER INSTRUCTIONS LARGE HOOK & STRAP ANCHORAGE CONNECTOR! WARNING National standards and state, provincial and federal laws require the user to be trained before using this product. Use
More informationD Square Construction LLC
D Square Construction LLC Lock Out-Tag Out (LOTO) and Zero Voltage Verification (ZVV) Process and Plan Energized Work Process and Permit - 1 - Table of Contents 1) Instruction for using Decision Tree Analysis
More informationSeptember 23, 2016 Site Safe, Inc.
RF Exposure Utility Worker Safety and Small Cells September 23, 2016 Site Safe, Inc. RF SAFETY Radio Frequency (RF) Safety is worker and general public safety around wireless transmitters September 23,
More informationWalking-Working Surfaces and Fall Protection Standards Update. OSHA General Industry
Walking-Working Surfaces and Fall Protection Standards Update OSHA General Industry Background Slips, trips, and falls account for a majority of all general industry injury incidents. Caused 849 workplace
More informationINSTRUCTIONS FOR USE
INSTRUCTIONS FOR USE 7100 Series Lanyards Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046 Deer Park, TX 77536 Phone :
More informationProgressive Safety Services LLC - All Rights Reserved
Estimated that 2,000 workers are treated in specialized burn centers each year as a result of arc flash (Electrical Safety Foundation International). According to the National Safety Council, medical costs
More information1.2 LIMITATIONS: Consider the following application limitations before using this equipment:
User Instruction Manual Standing Seam Roof Anchor This manual is intended to meet the Manufacturer s Instructions, and should be used as part of an employee training program as required by OSHA. Figure
More information2017 NWHA TECHNICAL SEMINAR. Arc Flash Hazard Awareness MIKE BRENDLE LLC
2017 NWHA TECHNICAL SEMINAR Arc Flash Hazard Awareness WHAT IS ARC FLASH Arc Flash is a short circuit that flashes from one exposed live part to another, or to ground The result is ionized air that creates
More information1.3 LIMITATIONS: The following application limitations must be recognized and considered before using this product:
3965 Pepin Avenue Red Wing, MN 55066-1837 Toll Free: (800) 328-6146 Phone: (651) 388-8282 Fax: (651) 388-5065 www.protecta.com User Instruction Manual AJ720A Concrete Anchor This manual is intended to
More informationIWU PHYSICAL PLANT SAFETY PROGRAM. Revision: 1 ELECTRICAL SAFETY Section: 4
STANDARDS Title 29 Code of Federal Regulations (CFR) Part 1910 Subpart S 301-399; NFPA 70E 2012 1.0 INTRODUCTION Electricity is a serious workplace hazard, capable of causing both employee injury and property
More informationFALL PROTECTION COMPARISON BETWEEN VARIOUS OSHA STANDARDS, NAVY and EM 385 (2008) REQUIREMENTS
Requirements FALL PROTECTION COMPARISON BETWEEN VARIOUS OSHA STANDARDS, NAVY and EM 385 (2008) REQUIREMENTS Navy FP Chapter 13 of OPNAVINST 5100.23G (2005) and Fall Protection Guide for Ashore Facilities
More informationARC FLASH PROTECTION AT HEIGHTS
ARC FLASH PROTECTION AT HEIGHTS Arc Rated Fall Protection FallTech has you covered with Arc Rated products for the four components of a Personal Fall Arrest System (PFAS). Anchorage Connector When working
More informationFALL PROTECTION (SAF-SPI-06)
1. PURPOSE To describe the Ontario Operations standard methods for preventing serious injury resulting from fall from heights and to provide a Standard for Fall Protection to safeguard employees who work
More informationMANUFACTURING TECHNICAL INSTRUCTIONS - SAFETY FALL HAZARD CONTROL REQUIREMENTS SERIES & NO. SMI - 157
1 of 6 1.0 PURPOSE To establish minimum requirements and guidelines for controlling hazardous exposure of personnel to falls from working elevations in conformance with Federal and State OSHA rules and
More informationPreparer: Owner: Approver: EHS Team Member TES Manager Site Manager
Procedure No.: BMEHS-002.033 Page: 1 of 10 Preparer: Owner: Approver: EHS Team Member TES Manager Site Manager Document Revision Change Table Revision Revision Description Revised Revision Number New By
More informationINSTRUCTIONS FOR USE
Rebar Chain Assembly INSTRUCTIONS FOR USE 7260XX Rebar Chain Assembly Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046
More informationElectrical Safety Program
Facilities Operations and Development Environmental Health and Safety 1314 Kinnear Road #106 Columbus, OH 43212-1168 614-292-1284 Phone 614-292-6404 Fax www.ehs.osu.edu Electrical Safety Program Prepared
More informationThe Pennsylvania State University Energized Electrical Safety Program
Introduction: The Pennsylvania State University Energized Electrical Safety Program Purpose: Electricity is a serious workplace hazard, capable of causing both employee injury and property damage. It is
More informationRegulation Summary: Walking-Working Surfaces & Personal Protective Equipment (Fall Protection Systems); OSHA s Final Rule
Regulatory Update Regulation Summary: Walking-Working Surfaces & Personal Protective Equipment (Fall Protection Systems); OSHA s Final Rule General Industry 29 CFR 1910 On November 17, 2016, OSHA published
More informationPreview to the 2018 NFPA 70E, the Standard for Electrical Safety in the Workplace
Preview to the 2018 NFPA 70E, the Standard for Electrical Safety in the Workplace Preview to the 2018 NFPA 70E, the Standard for Electrical Safety in the Workplace Technical Committee Members James Dollard,
More informationOSHA s new walking working surfaces standards
OSHA s new walking working surfaces standards changes and new requirements Inspection of walking working surfaces 1910.22(d) Regularly and as needed and correct, repair, or guard against hazardous conditions;
More informationReliance Industries, LLC Operating instructions for the / Bolt-on D-Ring Anchorage. Model # 3071
Reliance Industries, LLC Operating instructions for the 3071-1 / 3071-2 Bolt-on D-Ring Anchorage Model # 3071 Reliance Industries, LLC PO Box 140008 Denver, CO 80214 Ph. (800) 488-5751 Ph. (303) 424-8650
More informationThis is (Enter Company Name Here) Arc Flash Prevention policy. (Enter Name Here) will be responsible for overall direction of the Safety Program.
Company Name: Policy/Procedure ID Number: 222 Date: Grainger Safety Services Inc. 2012 Arc Flash Prevention Policy This is (Enter Company Name Here) Arc Flash Prevention policy. (Enter Name Here) will
More informationUser Instruction Manual Fixed Beam Anchor
Instructions for the following series products: FIXED BEAM ANCHOR Model Numbers: The Ultimate in Fall Protection 2108406 2108407 2108408 2108409 2108410 2108411 User Instruction Manual Fixed Beam Anchor
More informationOperating instructions. Bolt-on Bar Joist Anchorage
Reliance Industries, LLC Operating instructions for the Bolt-on Bar Joist Anchorage Model # 3072 Reliance Industries, LLC PO Box 140008 Denver, CO 80214 Ph. (800) 488-5751 Ph. (303) 424-8650 Fax (303)
More informationTelecommunication Tower Technician Course Descriptions
Telecommunication Tower Technician Course Descriptions Developed by: TES, Inc. 10909 Murdock Drive Knoxville, TN 37932 800-327-4036 O*NET-SEC CODE: 49-2021.00 RAPIDS CODE: 2030CB Approved By US Department
More informationLockout / Tagout Safety Program
Lockout / Tagout Safety Program Prepared by: The Ohio State University Environmental Health and Safety Occupational Safety & Industrial Hygiene 1314 Kinnear Road Columbus, OH 43212-1168 614-292-1284 Phone
More informationCommittee Input No. 35-NFPA [ Chapter 1 ] Submitter Information Verification. Committee Statement
Committee Input No. 35-NFPA 1670-2015 [ Chapter 1 ] Chapter 1 Administration 1.1 Scope. 1.1.1* This standard shall identify and establish levels of functional capability for conducting operations at technical
More informationARKANSAS TECH UNIVERSITY FACILITIES MANAGEMENT HEALTH AND SAFETY MANUAL (LOCKOUT/TAGOUT) 30.0
() 30.0 The purpose of the Energy Control Policy (Lockout/Tagout) is to ensure that before any employee performs any servicing and/or maintenance on machinery or equipment, where the unexpected energizing,
More informationLEADER NOTES FOR MAY 2012 STAND-DOWN
LEADER NOTES FOR MAY 2012 STAND-DOWN BEST PRACTICES PHILOSOPHY Properly executed Insulate and Isolate ( I&I ) techniques allow line workers to safely work on and/or around energized parts. The Best Practices
More informationNFPA 70E What Changed? Keeping People Safe from Electrical Hazards for over 50 Years
NFPA 70E -2018 What Changed? Keeping People Safe from Electrical Hazards for over 50 Years Moderator Ron Spataro AVO Training Institute Marketing Manager Q&A Send us your questions and comments during
More information2018 NFPA 70E Significant Changes 7/27/2017. EFCOG Electrical Safety Task Group Workshop, July 2017
Significant Changes EFCOG Electrical Safety Task Group Workshop, July 2017 Appreciation Thanks to: Paul Dobrowsky creating the base PPT program Chair, Dave Dini for leading the Committee through the process
More informationDefinitions found in several locations:
Definitions found in several locations: NFPA 70 - National Electric Code NFPA 70B Recommended Practice for Electrical Equipment Maintenance. NFPA 70E Electrical Safety in the Workplace OSHA 1910 Subpart
More informationRecent changes in workplace safety regulations have heightened the awareness of hazards associated with electrical arcs.
Recent changes in workplace safety regulations have heightened the awareness of hazards associated with electrical arcs. The hazard level must be quantified and workers properly protected before entering
More informationNFPA 70E Policies and Best Practices
NFPA 70E Policies and Best Practices Overview o Understand Compliance Requirements o Provide guidelines for a safe work environment o Effectively communicate policies to employees and customers o Express
More informationDuke University - Facilities Management Department Environmental Safety and Health Program ELECTRICAL SAFETY PROGRAM
ELECTRICAL SAFETY PROGRAM Applicable to: All FMD Organizations Date Effective: 7/1/2014 Issue No.: 1 Revision: 0 Page 1 of 9 A. Purpose 1. To establish a written electrical safety program that promotes
More informationSECTION 51 NFPA 70E POLICY. Health & Safety Policy and Procedures Manual
SECTION 51 NFPA 70E POLICY Health & Safety Policy and 1. Protection Against Arc Flash A. Policy: An arc flash is a dangerous condition associated with the release of energy caused by an electric arc. An
More informationS Surge Arresters
Surge Arresters UltraSIL Polymer-Housed VariSTAR Type US, UH, and UX Station-Class Surge Arresters Installation and Maintenance Instructions Service Information S235-88-1 Contents Product Information...........................1
More informationELECTRICAL SAFE WORK PRACTICES
STAFF ELECTRIC ELECTRICAL SAFE WORK PRACTICES PURPOSE The purpose of this procedure is to protect all workers from injuries resulting from exposure to arc flash, arc blast and electrical shock and to comply
More information2012 NFPA 70E: Electrical Safety In The Workplace
ERI Safety Videos Preventing Injuries Through Employee Training 2984 2012 NFPA 70E: Electrical Safety In The Workplace Leader s Guide ERI Safety Videos 2012 NFPA 70E: Electrical Safety In The Workplace
More informationElectrical Safety Work Practices
Work Practices I. SCOPE This program covers any SOUTHWESTERN COMMUNITY COLLEGE employee that may work or be exposed to exposed electrical systems: To assure that employees are not exposed to potentially
More informationElectrical & Arc Flash Safety Program 2007
University of Louisville Physical Plant Department Electrical & Arc Flash Safety Program 2007 Introduction Electricity is a serious workplace hazard, capable of causing both employee injury and property
More informationOccupational Protective Equipment
Introduction One of the leading occupational dangers in today s workforce is the risk of death or injury due to falls. Falls from ladders, scaffolds, buildings, or other elevations have become the second
More informationWalking-Working Surfaces
Walking-Working Surfaces 29 CFR 1910, Subpart D Presented by: Chesapeake Region Safety Council Rod Markley, CSP, CHST, CET Subpart D - Walking-Working Surface Topics we will cover: Background of rule Overview
More informationPersonal Protective Equipment
Personal Protective Equipment 6500-2.0 Associated OHS Process: General Industry and Construction Safety The master copy of this document resides in electronic format. Printed copies of this document are
More informationMARINE CORPS BASE CAMP LEJEUNE PUBLIC WORKS DIVISION UTILITIES BRANCH STANDARD OPERATING PROCEDURE SHOP 82, ELECTRICAL DISTRIBUTION
MARINE CORPS BASE CAMP LEJEUNE PUBLIC WORKS DIVISION UTILITIES BRANCH STANDARD OPERATING PROCEDURE SHOP 82, ELECTRICAL DISTRIBUTION SUPERVISOR, SHOP 82: (DATE) UTILITIES DIRECTOR: (DATE) PUBLIC WORKS SAFETY:
More information200 A, 15 and 25 kv class loadbreak bushing insert installation instructions
Loadbreak Apparatus Connectors Effective October 2013 Supersedes March 2011 200 A, 15 and 25 kv class loadbreak bushing insert installation instructions S500-12-1 DISCLAIMER OF WARRANTIES AND LIMITATION
More informationHealth and Fire Safety Review 2/15
Health and Fire Safety Review 2/15 1 TABLE OF CONTENTS Page 3 Scope 3 Control of Hazardous Energy (Introduction) 3 Authorized Employee 3 Employer Responsibility 4 Tagout Devices 4 Lockout Devices 5 General
More informationUser Instruction Manual Fixed Beam Anchor
User Instruction Manual Fixed Beam Anchor This manual is intended to meet the Manufacturer s Instructions as required by ANSI Z359.1 and ANSI A10.14, and should be used as part of an employee training
More informationUser Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor
1 User Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee
More informationFREQUENTLY ASKED QUESTIONS ABOUT FALL PROTECTION
FREQUENTLY ASKED QUESTIONS ABOUT FALL PROTECTION What s the difference between polyester and nylon webbing in harnesses and lanyards? Nylon (polyamide) and polyester are both synthetic products with very
More informationPersonal Protective Equipment Program
Personal Protective Equipment Program Document History Version Date Comments 0.1 June, 2017 Pinnacle Draft 0.2 August, 2017 FM-OHS Internal Review 1.0 November, 2017 Final Version Table of Contents Definitions...
More informationUSA Mobile, AL Electrical Safe Working Practices
Compliance Compliance with these safe work practices is mandatory. Failure to comply may result in disciplinary action. These Safe Working Practices apply to any person performing electrical work at the
More informationFALL PROTECTION
115500 FALL PROTECTION PART 1 GENERAL 1.01 General A. Cornell University seeks to prevent exposures to fall hazards whenever possible and protect personnel that may be exposed to fall hazards. Therefore,
More information2. The purpose of this program is to achieve the following objectives:
Section 16A. Lockout and Tagout Program 1. In the course of their duties, personnel at the TFREC may need to secure controls, switches, and equipment in order to prevent injury caused by the sudden, unexpected
More informationCOOPER POWER SERIES. VariSTAR Storm Trapper high energy MOV arrester installation instructions. Surge Arresters MN235017EN
Surge Arresters MN235017EN Effective October 2016 Supersedes S235-16-1 November 2009 COOPER POWER VariSTAR Storm Trapper high energy MOV arrester installation instructions SERIES DISCLAIMER OF WARRANTIES
More informationAdvances in Low Voltage Motor Control Center (MCC) Technology Help Reduce Arc-Flash Hazards and Minimize Risks
Advances in Low Voltage Motor Control Center (MCC) Technology Help Reduce Arc-Flash Hazards and Minimize Risks Selecting the right MCC equipment leads to improved plant safety, helping protect people and
More informationOperator's Manual Supplement
Operator's Manual Supplement Traveling Fall Arrest Anchor System Original Instructions First Edition Fifth Printing Part No. 1256390GT Operator's Manual Supplement Genie Self-propelled Boom Products and
More informationLOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM
LOCK-OUT/TAG-OUT (LO/TO) SAFETY PROGRAM REGULATORY STANDARD: OSHA - 29 CFR 1910.147 BASIS: Approximately three million workers in the United States face risks from uncontrolled energy when servicing machinery
More informationDocument Owner: Name: Phil Langlois Position: Lead Electrical Engineer
Department 015-07-08 Page 1 of 10 Training Code: EL306 (5 year renewal) Document Owner: Name: Phil Langlois Position: Lead Engineer Sud = Sudbury, Ontario, PC = Port Colborne, Thom = Thompson, Manitoba,
More informationLock Out - Tag Out Safety Program
Lock Out - Tag Out Safety Program Daniel Schmid 4-22-15 Pam Schmid 4-22-15 Dan Schmid Pam Schmid Safety Director Quality Director Table of Contents DOCUMENT REVISION TABLE... 3 PURPOSE... 4 RESPONSIBILITY...
More informationElectrical Safety Program
Electrical Safety Program Date of last revision: October, 2011-485 - Electrical Safety Program Update No updates. - 486 - Electrical Safety Program Update...486 (I) Purpose...488 (II) Policy...488 (III)
More information??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls.
Intent??????? is committed to providing a safe work environment for its employees and preventing occupational injuries due to falls. Fall Protection is an integral part of our commitment to a safe work
More informationRisk Assessment Procedure
Voltage, current testing, troubleshooting Infrared inspection Visual inspection, data collecting Risk Register ES Acc 6 4 1 1 6 36 ES < Acc 6 4 3 3 10 60 AF/AB 40 Acc 8 3 2
More informationStandards of Practice Personal Protective Equipment
Document Authority: I. PURPOSE Standards of Practice Personal Protective Equipment Whenever feasible, hazards must be eliminated through engineering, and/or administrative controls, prior to resorting
More informationProduct Information Report Lockout/Tagout Hazardous Energy Control
Overview A properly implemented (LOTO) program is designed to protect workers involved in the maintenance and servicing of equipment from the dangerous effects of hazardous energy caused by the unexpected
More informationworkplace fatalities involving falls to a lower level. Fall related fatalities make up 16% of workplace fatalities
2013 574 workplace fatalities involving falls to a lower level Fall related fatalities make up 16% of workplace fatalities Bureau of Labor Statistics Passive Fall Prevention Fall Arrest Fall Restraint
More informationDUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM
DUQUESNE UNIVERSITY LOCKOUT/TAGOUT PROGRAM Prepared by: Environmental Health and Safety Department TABLE OF CONTENTS Page Purpose 1 Scope 1 Introduction 2 Regulatory Requirements 2 Protective Materials
More information