2016 Road Electronic Frame Fit Specifications This document is intended to communicate general frame fit guidelines for SRAM electronic products.

Transcription

1 206 Road Electronic Frame Fit Specifications This document is intended to communicate general frame fit guidelines for SRAM electronic products. For additional information, please contact your SRAM representative. Gen Rev C 205 SRAM, LLC

2 Table of Contents Electronic Shifter...4 Unified Shifter Remote Shifter Shifter Brake... Electronic Front Derailleur...2 RED Electronic Frame Fit Specifications for SRAM Electronic rear derailleur and crankset are the same as Red mechanical rear derailleur and Red 2x crankset. This can be found in the SRAM Road Frame Fit Specifcations

3 Information in this document is for specifications unique to the electronic road products. Consult the mechanical Road Frame Fit Specifications document rear derailleur dimensions. All dimensions are in millimeters unless otherwise noted. Images in this document are not to scale. Your product's appearance may vary slightly from the images in this document. Information in this document is subject to change without prior notice. If you have any questions please contact your SRAM representative.

4 Electronic Shifter

5 Unified Shifter Unified Shifter Dimensions 8 mm 40.6 mm 6.5 mm 2 Front (Button side) Side Back (Battery/Mount) Notes: Overall dimensions are subject to change during the development. 2 Button access needed for pairing and adjustment of the derailleurs Rev C Electronic Shifter

6 Unified Shifter Unified Shifter with Connectors 8 mm 72 mm Notes: Allow sufficient space for shifter and connector length in desired mounting location Rev C Electronic Shifter

7 Unified Shifter Mounting Specifications 4 90 Lock mount Threaded direct mount M4x0.7 thread pitch, 4.6 mm depth Notes: Consider additional clearance for 90 lock mount Cable connections can be made after mounting with proper port access. Button access is only needed for setup. 90 mount is compatible with all SRAM/Zipp Quickview mounts. Unified shifter must be mounted externally on the bike to maintain integrity of the wireless signal Rev C Electronic Shifter

8 Remote Shifter Remote Shifter and Connector Dimensions Left shift button Right shift button 2 Wire lengths 50 mm 230 mm 450 mm 650 mm 2.5 mm wire diameter 3.35 mm 5.0 mm connector diameter Notes: Consider the connector diameter and wire length when routing wires internally. 2 Choose the wire lengths based on application and desired location of the remote shift button Rev C Electronic Shifter

9 Remote Shifter Internal Mounting Specifications Side A Side B 00 mm 2 00 mm Notes: 2 Internally mounted shifter setup requires the remote shifter wires to be routed external of bar, stem, and frame materials a minimum of 00 mm per side. Routing under bar tape is acceptable within the 00 mm length Rev C Electronic Shifter

10 Remote Shifter Remote Shifter Mounting mm bar 3.8 mm bar mm TT Extensions Notes: Button holder designed for 3.8 mm bar mounting. 2 Direct mount under the handlebar tape for 22.2 mm through 35 mm diameter bars Rev C Electronic Shifter

11 Shifter Brake Remote Shifter Connections 2 Notes: The left and right shifter brake each provide two additional ports for auxiliary remote shifter buttons. Use plugs when remote shifters are not in use. Provide a small amount of slack in the wire for shifter brake repositioning. Route the wires underneath the bar tape. 206 Rev C Electronic Shifter

12 Electronic Front Derailleur

13 RED Electronic Front Derailleur Dimensions Hanger contact face Fixation bolt center Rev C Electronic Front Derailleur

14 RED Electronic Front Derailleur Frame Compatibility and Capacity Information Chainring Chainline A (mm) Fixation bolt position B Chainstay angle C (mm) Chainstay length 55/ / x 52/36 45 mm / /36 33 * For 32T cassettes the chainstay angle (B) is B A C Rev C Electronic Front Derailleur

15 RED Electronic Front Derailleur Cage Alignment Chainring D (mm) Hanger offset from seat tube axis E Hanger angle relative to seat tube axis F (mm) G (mm) Outer cage position above chainring 55/42 53/39 2x 52/ ± 0.5 ±.5 > 0.75 ± /34 46/36 D E G F Rev C Electronic Front Derailleur

16 RED Electronic Position of Front Derailleur with Clamp Adapter Chainring H (mm) Lower clamp position I (mm) Upper clamp position 55/ / x 52/ / / H I BB Axis Rev C Electronic Front Derailleur

17 RED Electronic Clearance Between Front Derailleur and Frame A (mm) B (mm) C (mm) D (mm) E (mm) F (mm) 30 OLD: Clearance Between Front Derailleur and Crank Arm G (mm) H (mm) Fixation bolt center A 27 A A G Bottom bracket center 8.7 Ø B 57 C Fixation bolt center D E F H Tire clearance to battery 20. D Rev C Electronic Front Derailleur

18 RED Electronic Braze-on Hanger Dimensions R ±0.5 mm Center line of seat tube to center line of bottom bracket 8.7 R Rev C Electronic Front Derailleur

19 GEN Rev C 205 SRAM LLC