Transfer Chain (SA-1002) & Adjustable I-Beam Clamp (SA-1039 or SA-1040) Operating Instructions
|
|
- Brianne Richards
- 6 years ago
- Views:
Transcription
1 Transfer Chain (SA-1002) & Adjustable I-Beam Clamp (SA-1039 or SA-1040) Operating Instructions SPIDER Page 1 of Rev A
2 Using Transfer Chain with Adjustable I-Beam Clamp Safety Notes Do not use equipment if you do not understand operating and handling procedures. Always inspect equipment before each use. Do not use equipment if you question that it is in safe working condition. Report unsafe equipment immediately to proper personnel. Follow all safety rules and regulations. Failure to do so can result in injury or death. Wear Safety Harness, tied off to independent anchor points. Properly secure and store equipment when not in use. Each connection point on the beam can add additional loads to the beam and need to be considered by a qualified person before the system is used. For the connection point of the main suspension line the connection must be rated for 4x (the hoist capacity rating). For the connection point of the transfer chain rigging hooks the load rating is 4x (the dead weight of the equipment and the live load). The connection point for the independent safety line must be rated for either 5000 lbs. or for an engineered designed/controlled system 2x (the potential impact energy). Introduction Transfer chain (SA-1002) Is intended to support the weight of any Spider Model Basket equipped with chain guards on the fairlead. It allows for walking the rigging point by transferring weight back and forth from the transfer chain to rigging point to move along a horizontal structural beam and around vertical obstacles. Typical max. distance approximately 18 inches. Makes it possible to transfer from the rigging point to transfer chain, to allow repositioning of the rigging point and reloading the main suspension wire rope. Eliminates need to lower stage to ground to move rigging point. Minimum I-beam flange width 7-1/2 Adjustable I-Beam Clamp (SA-1039 or SA-1040) are intended to be used on the bottom flange of a horizontal I-Beam or Structural T. The flange not to be narrower than 1-1/2 in. (38 mm) and not wider than 4 in. (102 mm) for the SA- 1039, or 8 in. (203 mm) for the SA The beam shall be capable of sustaining four times the maximum rated working load of the basket. I-beam clamps are adjustable to width of I-beam flange, with Rigging Bar parallel to I-beam flange slide I-beam hook inward to within 1/32 to 1/8 of I-beam flange. Lock in place by rotating Rigging Bar to perpendicular position in relation to I-beam flange. When using with Transfer chain do not rotate past 50 degree angle. Use with 5/8 anchor bolt shackle. SPIDER Page 2 of Rev A
3 Steps 1. Before beginning the process of rigging the transfer chain, Worker to be secure with independent personal fall arrest system (Harness & Connecting Device) to I-beam with a separate I-Beam Clamp or I-Beam Roller as shown in figure 1. Ensure transfer chain is secured to basket, so that it s not accidentally dropped. Separate fall arrest Connection point figure 1 2. Position Sling and Rigging Hooks onto lower I-beam flange as shown in figure 2a and 2b, pull chain downward to apply tension then install optional 5/16 pear shaped thimble eye snap hook Carabineer through chain link closest to rigging hook body with chain pulled tight. Carabineer intent is to keep hooks in place on flange when the chain is not under tension. 3. Check installation by spreading Sling and Rigging hooks and seeing if they can come off beam, if components are secured go to step 4, if not repeat step 2 above until components are secure. figure 2a Caution: If Carabineer noted in steps 2 & 3 is not being used keep an eye on the transfer chain hooks to make sure that they are snug on the beam and that the chain is tight under tension prior to disconnecting the main suspension line. With slack in the chain the hooks could become disengaged. SPIDER Page 3 of Rev A
4 figure 2b 4. Thread chain through both sides of chain guards (both fairlead legs) as shown in figure 3a and 3b. figure 3a figure 3b SPIDER Page 4 of Rev A
5 5. Next position grab hook onto chain and attach shackle on chain as shown in figure 4a and 4b. figure 4a figure 4b SPIDER Page 5 of Rev A
6 6. Perform a final check on all positioned and secured components. 7. Press the DOWN Control lever to begin descent until the work basket is fully suspended from the transfer chain and there is appropriate slack in the primary wire rope to disconnect as shown in figure 5. Be sure to use the tension holder to keep the wire rope from going slack on the drum (Maintaining tight wrap). figure 5 8. Plan your moves and keep your rigging device attached to the beams. Slide as needed vs removing whenever possible. Recheck all connections prior to loading as shown in figure 6a and 6b. figure 6a SPIDER Page 6 of Rev A
7 figure 6b 9. Press the UP Control lever to begin ascent until work cage is fully suspended from your primary connection and that there is appropriate slack on the transfer chain to disconnect as shown in figure 7a and 7b. figure 7a SPIDER Page 7 of Rev A
8 figure 7b 10. After completions of transfer, proceed to next desired work location. 11. Reverse rigging procedures to return to your original location if necessary. 12. Properly secure and store equipment when not in use. SPIDER Page 8 of Rev A
SAMPLE PAGE. Section 2... Wire Rope
Section 2...................................................... Wire Rope Never use any kind of clip to directly connect two straight lengths of wire rope to form a continuous piece. Do not make up slings
More informationIMPORTANT: If you have questions on the use, care, or suitability of this equipment for your application, contact DBI/SALA.
User Instruction Manual Precast Concrete Beam Horizontal Lifeline System This manual is provided as the Manufacturer s Instructions, and should be used as part of an employee training program as required
More informationFigure 1 - Parts Identification. Copyright 2002, DB Industries, Inc.
User Instruction Manual Zorbit Energy Absorber Kits for Horizontal Lifeline Systems This manual is provided as the Maunfacturer s Instructions, and should be used as part of an employee training program
More informationSPIDER BASKET ST-17 Rev
SPIDER BASKET ST-17 Rev 3-8-2017 TOPICS Specifications Components Inspection Job Preparation Operating Instructions Lifeline & Rope Grab Rigging Lift Plan Regulations Dimensions Specifications Model: ST-17
More informationFigure 1 - Parts Identification
Instructions for the following series products: Zorbit Energy Absorber Kits (See back page for specific model numbers.) User Instruction Manual Zorbit Energy Absorber Kits for Horizontal Lifeline Systems
More informationFall Protection Checklist. Guardrail System
Fall Protection Checklist Location/Department: Date of Inspection: Inspectors: Corrective Actions: Work order/memos were issued: Yes No Date issued: In accordance with the MIOSHA and OSHA standards the
More informationUser Instructions 1789 Parapet Wall Anchor
User Instructions 1789 Parapet Wall Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required
More informationFall Protection Refresher Orientation. Fall Protection Refresher Orientation 1
Fall Protection Refresher Orientation Fall Protection Refresher Orientation 1 Course Objectives! Understand the definitions of fall prevention, fall restraint, and fall arrest.! Understand the requirements
More informationHeavy Equipment Technician Rigging
1. What is SWL? a. Single weight of load b. Second weakest location c. Working load limit Heavy Equipment Technician IP Red Seal Practice Exam d. Abbreviation for swivel Heavy Equipment Technician Rigging
More informationUser Instruction Manual Tripod Anchorage Connectors
User Instruction Manual Tripod Anchorage Connectors This manual is intended to meet the Manufacturer's Instructions as required by ANSI Z359.1 and ANSI A10.14, and should be used as part of an employee
More informationOWNER'S MANUAL. Turnbuckle. Stanchions. Warning
GEMTOR, INC....when your life is on the line One Johnson Avenue Matawan, NJ 07747 732-583-6200 800-405-9048 Fax 732-290-9391 OWNER'S MANUAL Installation, Operating, Inspection and Maintenance Instructions
More informationDO NOT use any Alien Flier Zip Line Products or Accessories until you read and understand these SAFETY WARNINGS!
! WARNING DO NOT use any Alien Flier Zip Line Products or Accessories until you read and understand these SAFETY WARNINGS! A zip line can be very dangerous. Do not use this kit if you do not understand
More informationWINSAFE Corp. Operating Instructions For Outrigger Davit. Winsafe Part # WSOR208
WINSAFE Corp. Operating Instructions For Outrigger Davit Winsafe Part # WSOR208 These instructions must be read and understood by anyone installing or suspending equipment from Winsafe modular beams and
More informationUser Instructions 1790 Rail Anchor
User Instructions 1790 Rail Anchor This document is intended to meet the Manufacturer s Instruction requirements as stated by ANSI Z359.1, and should be used as part of an employee training program as
More information1.2 LIMITATIONS: Consider the following application limitations before using this equipment:
User Instruction Manual Standing Seam Roof Anchor This manual is intended to meet the Manufacturer s Instructions, and should be used as part of an employee training program as required by OSHA. Figure
More informationBEAMGUARD SAFETY POST TM INSTRUCTIONS
BEAMGUARD SAFETY POST TM INSTRUCTIONS READ THESE WARNINGS BEFORE USING THE BEAMGUARD SAFETY POST! 1. Before use of this system, read and understand all instructions, warnings, cautions and notes marked
More informationUser Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor
1 User Manual 1792 Standing Seam Metal Roof Retractable Swivel Anchor This manual is intended to meet the Manufacturer Instructions as required by ANSI Z359.1 and should be used as part of an employee
More informationOPERATION and MAINTENANCE Guide
Catalog No. AIR1000 Winch and Hoist OPERATION and MAINTENANCE Guide Cat. No. AIR1000 1250 Lb. Single Line Pull READ THIS BEFORE OPERATING UNIT INSTALLATION: Mount on clean, flat surface. Use 1/2" mounting
More informationUser Instruction Manual Fixed Beam Anchor
User Instruction Manual Fixed Beam Anchor This manual is intended to meet the Manufacturer s Instructions as required by ANSI Z359.1 and ANSI A10.14, and should be used as part of an employee training
More informationUSER MANUAL Do not throw away these instructions. Read and understand these instructions prior to use of the Lad Grab Safety System.
PRODUCT NAME: LAD GRAB Patent Pending PART NUMBERS: *LAD GRAB2TOPBRACKET, *LAD GRAB2CABLEGUIDE, *LAD GRAB2BOTTOMBRACKET, & CABLE3/8AIRCRAFT USER MANUAL Do not throw away these instructions. Read and understand
More informationUser Instruction Manual Fixed Beam Anchor
Instructions for the following series products: FIXED BEAM ANCHOR Model Numbers: The Ultimate in Fall Protection 2108406 2108407 2108408 2108409 2108410 2108411 User Instruction Manual Fixed Beam Anchor
More information8012, 8018 & ,000 LB. CAPACITY HOOK-TYPE CABLE SHEAVES
OPERATION, SERVICE AND PARTS INSTRUCTION MANUAL 80, 808 & 804 8,000 LB. CAPACITY HOOK-TYPE CABLE SHEAVES Read and understand this material before operating or servicing this sheave. Failure to understand
More informationFall Protection Training
Fall Protection Training Reference: OSHA 29CFR 1910 OSHA 29CFR 1926 ANSI Z359.1-1992 (R1999) Introduction Deaths occurring from falls during 1996 increased five percent over 1995 figures. This accounts
More informationProduct Name: Beamer Trolley Anchor
Product Name: Beamer Trolley Anchor Part #: 00215 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety
More informationInstallation, Operating, Inspection and Maintenance Instructions Ladder Climber s Safety System. Warning
OWNER'S MANUAL Installation, Operating, Inspection and Maintenance Instructions Ladder Climber s Safety System Model # s: 6000, 6001, 6010 Warning You must read and fully understand all instructions, or
More informationPhysics and Body Mechanics for Suspension bondage
Physics and Body Mechanics for Suspension bondage People are not objects We can use physics to model and approximate suspension systems using people. But it is very important to remember that people are
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More information1.3 LIMITATIONS: The following application limitations must be recognized and considered before using this product:
3965 Pepin Avenue Red Wing, MN 55066-1837 Toll Free: (800) 328-6146 Phone: (651) 388-8282 Fax: (651) 388-5065 www.protecta.com User Instruction Manual AJ720A Concrete Anchor This manual is intended to
More informationBEAMGUARD SAFETY POST TM
BEAMGUARD SAFETY POST TM INSTRUCTIONS-SAFETY FIRST! READ THESE WARNINGS BEFORE USING THE BEAMGUARDS! 1. Before use of this system, read and understand all instructions, warnings, cautions and notes marked
More informationInstruction Manual AC350 GUIDED-TYPE FALL ARRESTER ON RIGID ANCHORAGE LINE EN 353-1:2002
GENERAL CONDITIONS OF UTILIZATION 5 6 7 8 9 - should be filled in by competent person and kept during whole period of the system usage. COMISSION AND FIRST USE - after installation of the working rope
More informationBANKSMAN / SLINGER. 1. What is the smallest size diameter of synthetic rope allowed for use as a hand held tagline?
BANKSMAN / SLINGER 1. What is the smallest size diameter of synthetic rope allowed for use as a hand held tagline? A. 16mm B. 10mm C. 12mm 2. What is the maximum temperature that a webbing sling can be
More informationMANITOWOC MODEL TON CAPACITY
LIFTING CHARTS - Crawler Cranes ANITOWOC ODEL - TON CAPACITY BOO RIGGING GUIDE ODEL # HEAVY LIFT BOO Table of Contents General... Assist Crane Requirements... Accessing Parts... Installation and Removal
More informationBuckingham Mfg. Co., Inc. OX BLOCK TM Instructions and Warnings
OVERVIEW The Buckingham OX BLOCK is a rope snatch block with an integrated friction bar used for lowering loads, snubbing loads, and raising loads. It allows the rigging professional to handle loads with
More informationIssue Date 12/01/09 Revision Date 01/04/18 Fall Hazard Management
Purpose This Practice provides the minimum requirements to ensure the safety of employees performing work in elevated areas. Scope All LLC Companies including, Blanchard Industrial, LLC, Grand Isle Shipyard,
More informationFigure 1 - Cable Grip Horizontal Lifeline Termination ZORBIT ENERGY ABSORBER RELEASE TAB
Instructions for the following series products: Cable Grip (See back pages for specific model numbers.) User Instruction Manual Cable Grip Kit for Horizontal Lifeline Systems This manual is provided as
More informationAirwalker. Installation and Safety Information. Stretch Products for Dance, Therapy, Education, and Fitness
Airwalker Installation and Safety Information Stretch Products for Dance, Therapy, Education, and Fitness www.dyenamicmovement.com Airwalker is a Registered Trademark of Dye namic Movement Products, Inc.
More informationCrane & Rigging Brain Teasers
Crane & Rigging Brain Teasers Host: Mike Parnell President/CEO, ITI ASME B30 Vice Chair (Cranes & Rigging) ASME P30 Chair (Lift Planning) The views expressed in this presentation are that of ITI and are
More informationHeavy Equipment & Rigging Specialist Training
Heavy Equipment & Rigging Specialist Training Module 1 Unit 4: Intro to Rigging May08 1 Key Points Review of Exercise Goals Discuss Rigging Components Language of Crane Signals Review Anchor Installation
More informationFall Protection ABC s
Fall Protection ABC s Chris Caron American Safety & Supply, Inc. Fall Protection ABC Itinerary Review types of fall arrest systems Review and discuss ladder safety Discuss the various components of fall
More informationProduct Name: Hold Me Rope Anchor
Product Name: Hold Me Rope Anchor Part #: 01300 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety
More informationBuckingham Mfg. Co., Inc. OX BLOCK TM Instructions and Warnings
OVERVIEW The Buckingham OX BLOCK is a rope snatch block with an integrated friction bar used for lowering loads, snubbing loads, and raising loads. It allows the rigging professional to handle loads with
More information8. Fall Protection Procedures WAC
1.0 Fall Protection Introduction 8. Fall Protection Procedures WAC 296-155-245 If an employee is exposed to a fall hazard of ten (10) feet or more in height, the employee must use a fall restraint, fall
More informationOccupational Protective Equipment
Introduction One of the leading occupational dangers in today s workforce is the risk of death or injury due to falls. Falls from ladders, scaffolds, buildings, or other elevations have become the second
More information8-20 Place edge protection to protect rope and webbing.
8-20 Place edge protection to protect rope and webbing. NOTE: All personnel working near an edge must take fall protection precautions as required by the AHJ. Edge personnel must place the edge protection,
More informationIMPORTANT: Record the product identification information from the ID label in the inspection and maintenance log in section 9.0 of this manual.
Instructions for the following series products: Vacuum Anchor HLL System (See back page for specific model numbers.) User Instruction Manual Vacuum Anchor Horizontal Lifeline System This manual is intended
More informationBC Shackle. Made in the China. Alloy Steel Anchor Shackle. Instructions for handling and use - Please read in full before using this device
BC Shackle Made in the China Alloy Steel Anchor Shackle Instructions for handling and use - Please read in full before using this device Index 1.) Introduction 2.) Warnings / General Use Guidelines 3.)
More informationSTORES FALL PROTECTION EQUIPMENT INVENTORY
#1 Talon Self Retracting Lifeline #2 Cable Type Lifeline Serial No: 6791 Model No. 3101051 Length: 16 feet Serial No: 01029 Model No. AD115BC Length: 10 feet #3 Steel Twist-Lock Carabiner #4 Steel Twist-Lock
More informationYou may order this publication from WCB Publications and Videos, Please quote ordering number BK60.
The following material is the property of the Workers Compensation Board of British Columbia and may not be reproduced by those outside of B.C. For those within British Columbia, this material may only
More informationEUROBUNGY-TRAMPOLINE
EUROBUNGY-TRAMPOLINE Set-up instructions of the new model 2004-2010 Photos are taken with the long and short Trailer WARNING for EUROBUNGIES without hydraulic rams There is a potential risk that a pole
More informationProduct Name: 2-Way Standing Seam Roof Clamp
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable
More informationProduct Name: Beamer Instruction Manual. Part #: 00110
Product Name: Beamer 12-1 Part #: 00110 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Guardian Fall Protection 6305 S. 231st St.,
More informationCompliance In A Can. Contents 1.0 HOW TO USE THIS MANUAL
Compliance In A Can This manual is intended to meet the Manufacturer s Instructions as required by ANSI Z359.1 and should be used as part of an employee training program as required by OSHA. Contents 1.0
More informationInstallation Drawings & Instructions Fall Protection Systems
ISO 9001 Registered Installation Drawings & Instructions Fall Protection Systems Attach the Cougar Slider only at this Sternum Connection Point CSA Z259.2.1-98 & ANSI Z359.1-M1992 [Canada & USA] Revision
More informationThe Penetrator was designed and tested only to be used on the Roof Zone Trailer #65028 with Flat Free Tires.
TM Roof Zone Cart Part #65033 TIE DOWN ENGINEERING Atlanta, GA 30336 www.tiedown.com (404) 344-0000 Penetrator Fall Protection Device Model #40620-A Model #40620-B U.S. Patent 9,675,824 Serious injury
More informationThe purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field.
Purpose The purpose of this training is to give field technicians awareness training and guidelines on potential hazards they may encounter in the field. Fall Protection and Prevention JELD-WEN Field Employees
More informationWalking-Working Surfaces Fall Protection Program
Purpose Walking-Working Surfaces Fall Protection Program The purpose of this program is to provide procedures to eliminate, prevent, and control hazards from falls from heights. Scope This program is applicable
More informationInstruction Sheet #08261 Rev Page 1 of 12
TM TIE DOWN ENGINEERING 255 Villanova Drive SW Atlanta, GA 30336 www.tiedown.com (404) 344-0000 Fax (404) 349-0401 Roof Zone Cart Part #65033 Penetrator Fall Protection Device Model #40620-A Model #40620-B
More informationAlpine WebLock 4.0. Made in the USA. 1-inch Slackline Webbing Anchor. Instructions for handling and use - Please read in full before using this device
Alpine WebLock 4.0 Made in the USA 1-inch Slackline Webbing Anchor Instructions for handling and use - Please read in full before using this device 1.) Introduction 2.) Warnings / General Use Guidelines
More informationUSER INSTRUCTIONS. Complies with ANSI Z359.1, ANSI Z359.4 standards and OSHA 29 CFR 1910 and 1926 regulations.
FALL PROTECTION USER INSTRUCTIONS TRIPOD SYSTEM Complies with ANSI Z359.1, ANSI Z359.4 standards and OSHA 29 CFR 1910 and 1926 regulations. Models: T100009, T210030B, T210060B, T210100B, T510000B, T510045,
More informationINSTRUCTIONS FOR USE
Rebar Chain Assembly INSTRUCTIONS FOR USE 7260XX Rebar Chain Assembly Complies with the current ANSI Z359.1-2007 and all applicable OSHA regulations and requirements. Reliance Industries P.O. Box 2046
More information"RIGGING SAFETY IN CONSTRUCTION ENVIRONMENTS"
PRESENTER'S GUIDE "RIGGING SAFETY IN CONSTRUCTION ENVIRONMENTS" Part of the "CONSTRUCTION SAFETY KIT" Series Quality Safety and Health Products, for Today...and Tomorrow OUTLINE OF MAJOR PROGRAM POINTS
More informationPremium PowerPoint Presentation. Rigging Review
Premium PowerPoint Presentation Rigging Review Chapter 1 Hoisting Safety Review: What about the CG Symmetrical vs. Asymmetrical Balanced and Unbalanced Lifting Lug Hooks Angle Deformation Safety Gates
More informationOPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH.
W. W. Patterson Company 3 Riversea Road Pittsburgh, PA 15233 Phone: 800-322-2018 FAX: 412-322-2785 OPERATIONS/PARTS MANUAL FOR PATTERSON'S WWP75H-10 HYDRAULIC WINCH. Please fill in the following blanks
More informationProduct Name: 2-Way Standing Seam Roof Clamp. Instruction Manual. Part #: 10600
Product Name: 2-Way Standing Seam Roof Clamp Part #: 10600 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Table of Contents Introduction
More informationBasic Rigging And Wire Rope
Basic Rigging And Wire Rope Presented By Master Builders of Iowa Basic Rigging and Wire Rope Topics Four Commandments of Rigging Sling Angles Types Of Hitches Types Of Slings Types Of Rigging Devices OSHA
More informationARKANSAS TECH UNIVERSITY FACILITIES MANAGMENT HEALTH AND SAFETY MANUAL
FALL PROTECTION (PERSONAL FALL ARREST SYSTEMS) 15.0 The purpose of this policy is to specify procedures and training for the safety of the employees in the Facilities Management Group while working on
More informationInstructions for use / test book
Technology to secure life Guided type fall arrester including a rigid anchor line Guided type fall arrester: AH 5 0158 EN 353-1: 2002 VG11 CNB/P/11.073 Instructions for use / test book Item number of the
More informationInstructions for the following series products:
Instructions for the following series products: U-Bolt Roof Anchors (See back page for specific model numbers.) User Instruction Manual U-bolt Roof Anchor This manual is intended to be used as part of
More informationUSER S INSTRUCTION MANUAL FOR THE INSTALLATION, OPERATION & MAINTENANCE OF THE GUARDIAN TEMPORARY HORIZONTAL LIFELINE SYSTEM
USER S INSTRUCTION MANUAL FOR THE INSTALLATION, OPERATION & MAINTENANCE OF THE GUARDIAN 04630 TEMPORARY HORIZONTAL LIFELINE SYSTEM 1 WARNING This is a design compatible component for a comprehensive Guardian
More informationFigure 1 - Snap Hooks and Carabiners PART NUMBER MANUFACTURER S ID YEAR OF MANUFACTURE PART NUMBER MANUFACTURER S ID YEAR OF MANUFACTURE
Instructions for the following series products: SNAP HOOKS AND CARABINERS (See back page for specific model numbers.) User Instruction Manual Snap Hooks and Carabiners This manual is intended to meet the
More informationOverview. Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used
FALL PROTECTION Overview Identify fall hazardous areas Describing potential fall hazards How appropriate portable and extension ladders are used Fall Protection All situations that expose personnel to
More informationMarine 6-Boat Free-Standing Racks SKU: Updated November 2011
Marine 6-Boat Free-Standing Racks SKU: 30-061 Updated November 011 Contains: Marine -Boat Free-Standing Racks (SKU 1-003) Marine 3 rd Boat Expansion Racks (SKU 1-0303) Marine Back Legs (SKU -001) 3 Sets
More informationThank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step*
PG 1 OF 9 PORTA-DOCK, INC. 74A ABL/APW 1056 & 44A FLB APW 1056 PORTA-LIFT Thank you for purchasing a Porta-Dock product! *Please read and follow these instructions step by step* STEP 1. Separate and group
More informationGUARDIAN FALL PROTECTION
2015 V2 GUARDIAN FALL PROTECTION Product Mini Catalog 2015 For more information, go to www.guardianfall.com or call 800.466.6385 OUR VISION TO ALWAYS BE THE MARKET S FIRST CHOICE FOR FALL PROTECTION AND
More informationGEMTOR. ... when your life is on the line OWNER'S MANUAL. FLW Series Self-Retracting Lanyard/Fall Limiter
GEMTOR TM... when your life is on the line OWNER'S MANUAL FLW Series Self-Retracting Lanyard/Fall Limiter Installation, Operating, Inspection and Maintenance Instructions Warning You must read and fully
More information11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions)
11.4 FALL-ARREST SYSTEM AND EQUIPMENT CHECKLIST (Must answer yes to all applicable questions) This checklist shall be completed either by the Competent Person or a person trained and designated by the
More informationRescue Technician: Rope Rescue Level II
Rescue Technician: Rope Rescue Level II Skill Sheet Package Based on NFPA 1006: Standard for Technical Rescue Professional Qualifications, 2013 Edition. Rhode Island Fire Academy March 2015 Skill Sheet
More informationApplying Construction Fall Protection Concepts to General Industry
Applying Construction Fall Protection Concepts to General Industry Applying Construction Fall Protection Concepts to General Industry Michael Tesmer, CSP and David Jewell, CSP Conney Safety Products This
More informationRescue Assist Kit. The Rescue Kit Includes:
Rescue Assist Kit ITEM# 018-6000 Our new rescue assist kit provides two ways to quickly, and easily deploy rescue efforts to a fallen worker. Utilize the rescue sling to retrieve a conscious worker or
More informationMATERIAL HANDLING - FIELD RIGGING SAFETY PROGRAM
Title: Material Handling - Rigging Effective Date: 12/4/2014 Control Number: THG_0049 Revision Number: 1 Date: 10/23/2015 Annual Review Completed: 5/13/2015 MATERIAL HANDLING - FIELD RIGGING SAFETY PROGRAM
More informationWe are the manufacturer & supplies of lifting
+91-8048600116 Bm Industries http://www.bmliftingindustries.com/ We are the manufacturer & supplies of lifting equipment, lashing equipment, hardware tools & other associated products in South India. Widely
More informationMade in the USA. For Fall Protection Only. SafeLok Part Description
Operations and Instruction Manual SafeLok Anchorage - Model # 4011 IM-0051 REV A Portable Concrete and Steel Anchorage Connector ANSI Z359.1-07 5,000 lbs / 22kn Made in the USA The 3/4 Fall Protection
More informationAnchorages. Beam Anchors 136 Horizontal Safety Lines 137 Anchorage Lines 138 Rope Grabs 139 Hard Point Anchors 140 Attachment Slings 141
134 01.6 Anchorages 136 137 138 139 140 141 135 These robust vertical and horizontal beam anchors offer secure attachment to a range of I beam and H beam construction steel profiles. BA 004 The SpanSet
More informationWildcat LB Winch Kit. Operator s Manual Installation Instructions Replacement Parts List. With Wireless Control System.
p/n 2259-560 Wildcat 4000 LB Winch Kit With Wireless Control System Operator s Manual Installation Instructions Replacement Parts List 2012 Arctic Cat Inc. Trademarks of Arctic Cat Inc. Thief River Falls,
More informationWARNING! DO NOT THROW AWAY THESE INSTRUCTIONS! READ AND UNDERSTAND BEFORE USING EQUIPMENT!
Guardian Fall Protection Kent, WA 800-466-6385 www.guardianfall.com GENERAL SYSTEM SELECTION CRITERIA: Selection of fall protection shall be made by a Competent Person. All fall protection equipment shall
More informationNautique Triton Clamping Board Rack V2
w w w.ro swe l l marine.co m Nautique Triton Clamping Board Rack V2 Installation & Usage Instructions Part # C917-180045 Information: info@roswellmarine.com If you have any questions please call : 1-21-68-11
More informationCOMPACT. VERSATILE. SAFE.
NANO-LOK SELF RETRACTING LIFELINES ONLY 1.6 POUNDS! COMPACT. VERSATILE. SAFE. REPLACE YOUR LANYARD TO REDUCE FALL DISTANCE AND IMPROVE SAFETY. Model Shown 3101211 THE ULTIMATE IN FALL PROTECTION PRODUCT
More informationReliance Industries, LLC Operating instructions for the / Bolt-on D-Ring Anchorage. Model # 3071
Reliance Industries, LLC Operating instructions for the 3071-1 / 3071-2 Bolt-on D-Ring Anchorage Model # 3071 Reliance Industries, LLC PO Box 140008 Denver, CO 80214 Ph. (800) 488-5751 Ph. (303) 424-8650
More informationFALL PROTECTION. Leader s Guide. Marcom Group Ltd.
1818 FALL PROTECTION Leader s Guide Marcom Group Ltd. Structure and Organization Information in this program is presented in a definite order, so that employees will see the relationships between the various
More informationPart #: 42000; 42001; 42002; 42003; 42004; 42005; 42006; 42008
Product Name: Velocity SRL Part #: 42000; 42001; 42002; 42003; 42004; 42005; 42006; 42008 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment!
More informationQUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift
INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your
More informationProduct Name: O-Torque Beamer
Product Name: O-Torque Beamer Part #: 00141 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction 1 Applicable Safety Standards
More informationHoisting Equipment Cable puller & Accessories
Yale hoists and trolleys are not ed for Cable puller model Yaletrac Pulling force 800-3200 It has a light weight, compact, high tensile aluminium alloy housing with a large flat bottom surface for increased
More informationUSE INSTRUCTIONS 4050 SKYLOC SELF-RETRACTING LANYARD
4050 SKYLOC SELF-RETRACTING LANYARD Complies with ANSI Z359.1-1998, OSHA 1926, and other applicable regulations and requirements. Reliance Industries 281-930-8000 P.O. Box 2046 888-362-2826 toll free Deer
More informationProduct Name: Rope Grab
Product Name: Rope Grab Part #: 01500; 01503; 01505; 01506; 01507; 01511 Instruction Manual Do not throw away these instructions! Read and understand these instructions before using equipment! Introduction
More information2.2. Anchorage Point A secure point of attachment for Lifelines, lanyards or deceleration devices.
Title: Elevated Walking/Working Surfaces (Fall Protection) Site Function: Safety Procedure No.: MC032.122 Page: 1 of 16 McIntosh Site Reviewed: 02/2013 Effective: 03/2013 Supersedes: 08/2012 Preparer:
More informationIF LAW ENFORCED WHERE THE BEAM TONGS ARE USED CONTRADICTS AN INSTRUCTION(S) OR PART OF AN INSTRUCTION(S), VESTIL IS NOT RESPONSIBLE FOR ANY
Beam Tongs Manual 009 0//00 update BT-SERIES BEAM TONGS INSTRUCTION MANUAL MODEL BT-0, -0, AND -0 VESTIL MANUFACTURING CORP. 999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 703 TELEPHONE: (0) 5-758 -OR-
More informationEWP3500A Winch. Thank You For Choosing OPERATING MANUAL. Winch Wiring. Mounting Plate. Solenoid. Rocker Switch. Baffle Ring. Clevis Hook and Pin
OPERATING MANUAL 2753 Michigan Road Madison, Indiana 47250 812-574-7777 EWP3500A Winch Winch Wiring Rocker Switch Solenoid Mounting Plate Baffle Ring Fairlead Clevis Hook and Pin Control Box Hardware Wireless
More informationFall Protection Introduction
Fall Protection Introduction Date: District: Site: Time: Department: Manager/Supervisor Name: In 1995, 1,048 construction workers died on the job, with 32 percent, or 335 of them, resulting from falls.
More informationSynthetic Rope Installation Guide Premium, Ultra Performance & Zeon Winch Lines
ORIGINAL INSTRUCTIONS SYMBOL INDEX SYMBOL EXPLANATION SYMBOL EXPLANATION Synthetic Rope Installation Guide Premium, Ultra Performance & Zeon Winch Lines Every winching situation has the potential for personal
More information