Installation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No

Size: px
Start display at page:

Download "Installation Instructions MODEL VSTI-A020 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Versa Steel Inc. Guide Cables No"

Transcription

1 Tank Indicator Installation Model: VSTI-A020, Stainless Reverse Read System Guide Cables No Guide Cables 1 August 4, 2011

2 Assembly Instructions: (Shown with a 2 board, 12 ft kit) ITEM NO. PART NUMBER DESCRIPTION QTY STAFF GUAGE BOARD WEIGHTED FLOAT CABLE TENSION ASSEMBLY COUPLING BRACKET SHEAVE HOUSING " X 3" THREADED PIPE NIPPLE " UNION " X 24" THREAD PIPE NIPPLE TARGET FLOAT CABLE WIRE ROPE CLAMP TANK BRACKET STAFF GAUGE CLOSURE BRACKET RULER BRACKET TANK BRACKET EXTENSION /16" HEX HEAD BOLT /16" HEX NUT /16" LOCK WASHER /16" FLAT WASHER WEIGHTED PLATE FLOAT GUIDE CABLE 1 2 August 4, 2011

3 There are different ways to assemble & mount the Staff Gauge Boards onto the tank. The method chosen largely depends on these factors: a. The height of the tank b. The equipment available c. Whether or not you are able to mount the Tank Brackets directly to the tank STEP A - Assemble Staff Gauge Boards 1. Each Staff Gauge Board comes with a mounted decal set displaying height values; Lay the boards on a flat surface in the correct order/orientation. 2. Install each bracket assembly using a Tank Bracket, Tank Bracket Extension, (4) Hex Head Bolts, (8) Flat Washers, (4) Lock Washers, and (4) Hex Nuts. Note: The Tank Brackets can point up or down, depending on installation needs. 3 August 4, 2011

4 3. Configure and install the top bracket assembly using the following parts: Tank Bracket, Tank Bracket Extension, Ruler Bracket, and Coupling Bracket, with (6) Hex Head Bolts, (12) Flat Washers, (6) Lock Washers & (6) Hex Nuts. Note: The pipe socket on the Coupling Bracket must point up to receive the Reeving Assembly. 4 August 4, 2011

5 4. Trim the bottom of the Staff Gauge Board as necessary to fit the height of the tank. Note: The Staff Gauge Closure Bracket is only required when the Staff Gauge Board needs trimming. 5. When attaching the Staff Gauge Closure Bracket, saw the Staff Gauge Board to length (as necessary), then drill an 11/32 hole through the Staff Gauge Board. Use a Hex Head Bolt, Lock Washer, and Hex Nut to secure the Staff Gauge Closure Bracket to the bottom of the Staff Gauge Board. STEP B - Mount the Staff Gauge Boards 2 Ways 1. Field conditions permitting, mount the Tank Brackets directly to the tank. Then mount each individual Staff Gauge Board to each bracket assembly One bracket, then one Staff Gauge Board, next bracket, etc. 2. If unable to mount brackets directly to the tank, the Staff Gauge Board can be mounted to a support channel first. This channel is supplied by the customer, and should be at least 5 wide and as tall as the tank, in order to sufficiently support the Staff Gauge Board assembly. Once all components of the Staff Gauge Board assembly have been mounted to the channel, the entire assembly can be raised and mounted onto the tank as a unit. Note: For tall tanks, this may be done in sections to prevent bowing. 5 August 4, 2011

6 3. Attach the Wire Rope Clamp to the Target. 4. Slide the Target with attached Wire Rope Clamp onto the Staff Gauge Board. 5. Temporarily tape or tie the Target to the Staff Gauge Board so that it will not fall when the Staff Gauge Board is lifted vertically into position. Note: No cable installation is needed at this time. STEP C - Reeving Assembly 1. Using the two Sheave Housings, assemble the 1 x 24 Threaded Pipe Nipple, 1 Unions, and 1 x 3 Threaded Pipe Nipples as shown below. 6 August 4, 2011

7 1 x 24 Threaded Pipe Nipple Sheave Housing x 3 Threaded Pipe Nipple Union Reeving Assembly Note: Positioning of the Reeving Assembly is important because it is used to determine the exact point of penetration for the 1 NPT Coupling, where the Reeving Assembly meets the roof of the tank. The Staff Gauge Board is mounted to the outside of the tank wall, and the Reeving Assembly directs the Float Cable from the Staff Gauge Board over and through the roof of the tank. 2. One end of the Reeving Assembly is attached to the Coupling Bracket. The other end connects to the customer-provided 1 NPT Coupling, located on the roof of the tank. 3. Placement of the Reeving Assembly should mark exactly where the cable meets the tank. It can be adjusted when necessary by adding or removing length to the 1 NPT nipples. 4. Disassemble the Reeving Assembly to seal all its pipe joints. 5. Reassemble the Reeving Assembly onto the tank. 6. The two Cable Tension Assemblies can now be installed at the roof of the tank. The Float Guide Cable will be installed in a later step. Note: The customer is encouraged to use all safety precautions, devices, and procedures when working in elevated locations. 7 August 4, 2011

8 Pipe may need to be cut & threaded to adjust for field conditions Partial tank shown 1 NPT Coupling (Customer Provided) (2) Cable Tension Assemblies Float Guide Cable (optional) Staff Gauge Board /16 Float Cable STEP D - Feeding the Float cable 1. Remove the covers of the Sheave Housing to aid in feeding the Float Cable through. 2. Attach the Float Cable to the Weighted Float. 3. Feed the Float Cable: The taped end of the Float Cable comes up from the Weighted Float, then feeds up and through the Reeving Assembly, down to the Target, outside the tank. 4. Make sure the Float Cable is running on the pulleys in the Sheave Housing before placing the covers back on. 5. Temporarily attach the Float Cable to the Wire Rope Clamp on the Target using two set screws. Note: You will later need to calibrate the length of the Float Cable by positioning the Target outside of the tank, to the same height as the liquid inside the tank. 8 August 4, 2011

9 Reeving Assembly Remove covers to aid feeding Float Cable /4 Float Cable Feed Float Cable ( ) up & through Reeving Assembly 9 August 4, 2011

10 Tank top installation view: Reeving Assembly Partial tank shown 34-1/4 Distance dependent upon field conditions (3) 1 NPT Couplings (Customer Provided) (2) Cable Tension Assemblies Staff Gauge Board Float Guide Cables August 4, 2011

11 STEP E - Weighted Plate at the bottom of the tank Note: Only used when Float Guide Cables are required 1. The Weighted Plate should be secured to the tank floor while the tank is empty. This can be done by welding, or using the two mounting holes provided. The eyes in the plate should line up with the Cable Tension Assembly on top of the tank. These eyes are 12 apart and are positioned in line with the Weighted Float. A plumb-bob may be used for accurate locating. Note: If the tank currently has liquid inside, the Weighted Plate and Float Guide Cable assemblies can be lowered into the tank. 11 August 4, 2011

12 Connector swaged onto 3/16 Float Cable Weighted Float Float Weights Float Guide Cable Feed the Float Guide Cables through the Weighted Float; One Float Guide Cable should feed through the hole on each side of the Weighted Float. 12 August 4, 2011

13 3/16 Float Cable Set Screws Wire Rope Clamp Target STEP F - Calibrate Target 1. Finally, adjust the Target to the height of the Weighted Float. This is done by loosening the two set screws, and pulling the Float Cable through until the Target represents the correct height of the Weighted Float inside the tank. 2. Tighten the screws and check for smooth operation by pulling down on the Target. 3. Cut off the excess Float Cable. 13 August 4, 2011

14 Weighted Float Float Guide Cable Weighted Plate STEP G.a Tension Guide Cables on an Empty Tank 1. Pull up on the Float Guide Cable to provide tension. The Weighted Plate should be affixed to the tank floor, so you will not be able to lift if off the tank floor. 2. Compress the conical spring and locking collar 3/8 to ½ ; Mark the cable at the top of the locking collar. Tighten the locking collar using the two set screws. (Be careful not to overtighten as this will damage the Float Guide Cable). 3. Install the 3 Threaded Pipe Nipple back onto the base of the Cable Tension Assembly. 4. Cut the excess Float Guide Cables at the top of the 3 Threaded Pipe Nipple. 5. Replace the pipe caps using a sealant that is strong enough to retain the cap, but allowing you to remove it later to adjust tension as required. 14 August 4, 2011

15 STEP G.b Tension Guide Cables on a Live Tank 1. Pull up on the Float Guide Cable until you feel the Weighted Plate being lifted off the tank floor. 2. Using a marker; mark the cable at the top of the locking collar. 3. Tighten the locking collar to the cable 3/8 to 1/2 down from the mark using the two set screws. (Be careful not to over-tighten as this will damage the Float Guide Cable). 4. Lower the conical spring, locking collar and Float Guide Cable down into the base. This should tension the Float Guide Cables without lifting the Weighted Plate off the bottom of the tank. 5. Install the 3 Threaded Pipe Nipple back onto the base of the Cable Tension Assembly. 6. Cut the excess Float Guide Cables at the top of the 3 Threaded Pipe Nipple. 7. Replace the pipe caps using a sealant that is strong enough to retain the cap, but allowing you to remove it later to adjust tension as required. 15 August 4, 2011

16 STEP H - Tension the Float Guide Cables 1. Tension the Float Guide Cable at the top of the tank using the Cable Tension Assembly. 2. Remove the cap from the Cable Tension Assembly and the 3 Threaded Pipe Nipple. 3. Slide the Float Guide Cable through the customer-provided 1 NPT Coupling. 4. Feed each Float Guide Cable through the base of each Cable Tension Assembly. 5. Loosen the 2 set screws on the locking collar to feed the Float Guide Cable through the conical spring & locking collar. CONGRATULATIONS, YOU ARE NOW DONE INSTALLING A TROUBLE FREE TANK LEVEL INDICATOR FROM VERSA-STEEL INC.! 16 August 4, 2011

17 17 August 4, 2011

18 18 August 4, 2011

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift

QUALITY ALUMINUM BOAT LIFTS, INC. INSTRUCTIONS. Dominator Lake Lift INSTRUCTIONS Dominator Lake Lift PHONE:251-986-3882 * FAX:251-986-3136 QABLDOMINATORINST.2014 P a g e 1 Quality Aluminum Boat Lifts, INC. Installation Instructions: Dominator Lake Lift Thank you for your

More information

Installation Instructions - Electric Steel Drive Systems for Arm Sets to ,

Installation Instructions - Electric Steel Drive Systems for Arm Sets to , Installation Instructions - Electric Steel Drive Systems for Arm Sets to 22 208-025, 209-025 NB /0/ 607-0029 404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 Step.

More information

Wellhead Mast. Installation and Operation Guide. Nanometrics Inc. Kanata, Ontario Canada

Wellhead Mast. Installation and Operation Guide. Nanometrics Inc. Kanata, Ontario Canada Installation and Operation Guide Nanometrics Inc. Kanata, Ontario Canada 2001 2005 Nanometrics Inc. All Rights Reserved. Installation and Operation Guide The information in this document has been carefully

More information

Model PSI Compressor with 3-Gallon Air Tank 12VDC

Model PSI Compressor with 3-Gallon Air Tank 12VDC Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing

More information

Installation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems , ,

Installation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems , , Installation Instructions - Electric Aluminum Drive Systems for Arm Sets to 22 Electric Arm Systems - 204-025, 206-025, 22-025 NB /0/ 607-0020 404 N. Marshall Ave. El Cajon CA. 92020 For technical support

More information

Pressure Dump Valve Service Kit for Series 2300 Units

Pressure Dump Valve Service Kit for Series 2300 Units Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit

More information

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup.

SERIES 2 RAMP OWNER S MANUAL TOOLS REQUIRED: BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. SERIES 2 RAMP OWNER S MANUAL BEFORE YOU BEGIN... Read and understand these instructions before beginning a ramp setup. Use caution and care for your back when lifting, pushing, pulling, folding or unfolding

More information

Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B

Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B Side-of-Pole Mount for 1 Module (SPM1) For Module Types A & B ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 080311-2 SP3363-1 Side-of-Pole Mount for 1 Module (SPM1)

More information

Assembly Guide ST200 FUNCTIONAL TRAINER

Assembly Guide ST200 FUNCTIONAL TRAINER Assembly Guide ST200 FUNCTIONAL TRAINER Assembly Guide ST200 FUNCTIONAL TRAINER To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding,

More information

a division of Enviro Safety Products

a division of Enviro Safety Products www.minutemanvac.com, a division of Enviro Safety Products.800.637.6606 Chassis 3 4 5 3 4 6 7 8 5 0 0 6 8 0 7 4 3 5 6 7 E 7e www.minutemanvac.com, a division of Enviro Safety Products.800.637.6606 Page

More information

Technical Bulletin. Parts and Service News. LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6

Technical Bulletin. Parts and Service News. LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6 Equipment Affected Technical Bulletin LPG Lock-Off valve replacement procedures for 4.2 Liter Ford V6 Ford 4.2L V-6 powered tractors with LPG fuel systems. Part Description Discrepancy Fuel Pressure Lock-off

More information

Universal Elevator Mount Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A.

Universal Elevator Mount Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI U.S.A. REQUIRED TOOLS AND MATERIALS: 2 Capable Adults Carpenter s Level 15 Tape Measure Pencil Universal Elevator Mount Owners Manual Customer Service Center N53 W2400 South Corporate Circle Sussex, WI 530 U.S.A.

More information

Parts Manual STRIKER Striker 2840 Parts List - PN Printed in USA 03/18/08

Parts Manual STRIKER Striker 2840 Parts List - PN Printed in USA 03/18/08 Parts Manual STRIKER 2840 Striker 2840 Parts List - PN 238155 - Printed in USA 03/18/08 Standard Parts Recommended General Wear Parts Ref No Part Description Qty Part No 1 Squeegee Hose Assembly

More information

First Team Sports, Inc. Blast Recreational Volleyball System

First Team Sports, Inc. Blast Recreational Volleyball System First Team Sports, Inc. Blast Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 3 Net Clamp L 2 Carabiner Clip C 1 Pulley Clamp M 1 ½ x 2 Hex Bolt D 4

More information

SECTION 2 RING MOUNT

SECTION 2 RING MOUNT SECTION 2 RING MOUNT Rotax aircraft engines are manufactured and supported by Rotax GmbH of Austria. Read and understand the Rotax manuals completely before starting with the engine installation, as they

More information

Tripod Setup Guide (M-TPx)

Tripod Setup Guide (M-TPx) Items needed: 1/2 inch wrench, mast level (M-MLA), medium size wire cutters, crescent wrench, all-purpose grease, tape measure, tie wraps, redi-mix cement (optional), shovel (optional), sledge hammer (for

More information

First Team Sports, Inc. Stellar Recreational Volleyball System

First Team Sports, Inc. Stellar Recreational Volleyball System First Team Sports, Inc. Stellar Recreational Volleyball System BILL OF MATERIALS A 2 Volleyball Vertical Post K 1 ½ Centerlock Nut B 2 Height Labels L 2 Carabiner Clip C 3 Net Clamp M 1 ½ x 2 Hex Bolt

More information

Specifications Testing & Adjusting Disassembly & Assembly

Specifications Testing & Adjusting Disassembly & Assembly SB4191E00 Jul. 2005 Specifications Testing & Adjusting Supplement for Quad Lift Mast D20/25/30/32/33S-3 G/GC20/25/30/32P-3 G/GC20/25/30/32E-3 Important Safety Information Most accidents involving product

More information

BALL STOP INSTALLTION GUIDE

BALL STOP INSTALLTION GUIDE BALL STOP INSTALLTION GUIDE GROUND SLEEVE INSTALLATION: 1. Locate the exact location of the ground sleeve. NOTE: Maximum recommended pole spacing is 20 feet on center. 2. Excavate the pole footing; refer

More information

K Page 1 of 48 Air Intake - Pg. 17

K Page 1 of 48 Air Intake - Pg. 17 K532-53168 Page 1 of 48 Air Intake - Pg. 17 Ref # Part Number Qty Description 24 25 041 06-S 1 Gasket, elbow 25 48 054 09 1 Elbow, air cleaner Discontinued not available at Kohler Co. 35 277116-S 1 Brace,

More information

1500 Follow Spot Yoke

1500 Follow Spot Yoke 1500 Follow Spot Yoke Rev 1.1 2004 City Theatrical, Inc. Getting Started with the City Theatrical Follow Spot Yoke Congratulations on the purchase of your City Theatrical Follow Spot Yoke. The City Theatrical

More information

PR4 Installation, Operation & Maintenance Instructions (DOT Certification Included)

PR4 Installation, Operation & Maintenance Instructions (DOT Certification Included) PR4 Installation, Operation & Maintenance Instructions (DOT Certification Included) March 2006 Form FVC 054 Rev. 6 KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER. The Passive - R4 device

More information

American Flagpole & Flag Co. 1(800)

American Flagpole & Flag Co.   1(800) SENTRY CONCEALED HALYARD-REVOLVING TRUCK GROUND SET INSTALLATIONS INSTRUCTIONS 1. Dig foundation as detailed in SECTION A FOUNDATION SPECIFICATIONS, set sleeve in enter of hole with top 2 above grade.

More information

PUNE TECHTROL PVT LTD. Instruction and Maintenance Manual for Float and Tape Gauge FTG

PUNE TECHTROL PVT LTD. Instruction and Maintenance Manual for Float and Tape Gauge FTG PUNE TECHTROL PVT LTD Instruction and Maintenance Manual for and Tape Gauge FTG INSTALLATION, OPERATION AND MAINTENANCE MANUAL FOR FLOAT AND TAPE GAUGE FTG 1 Introduction : It is used to measure and indicate

More information

PRO1030 Bi-Directional Assembly Replacement

PRO1030 Bi-Directional Assembly Replacement PRO1030 Bi-Directional Assembly Replacement 1. Remove both side covers using the Crank and Cover Removal procedure. Fig. 1 2. Disconnect both brake cables (not shown) from the brake (S3611). (Fig. 1) 3.

More information

Installation Instructions - Super Six Electric Arm Kits with Underbody Pivots , , ,

Installation Instructions - Super Six Electric Arm Kits with Underbody Pivots , , , Installation Instructions - Super Six Electric Arm Kits with Underbody Pivots 501-2112, 501-2113, 501-2114, 501-2115 GR 0/23/12 60-0135 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call

More information

Installation Instructions

Installation Instructions 116-3027, 116-3017 X-Pando Adjustable Steel Protector Installation Instructions 1404 N. Marshall Ave. El Cajon CA. 92020 For technical support call us at (800) 368-3075 NB 6/28/10 607-0112 Step 1. Mounting

More information

CentriFlow Meter Integrated Air Entrainment System

CentriFlow Meter Integrated Air Entrainment System CentriFlow Meter Integrated Air Entrainment System INSTALLATION & OPERATION MANUAL January 2004 Revision 021-4 EASTERN INSTRUMENTS 416 LANDMARK DR. WILMINGTON, NC 28412 910-392-2490 Fax: 910-392-2123 website:

More information

CO2 Tank Conversion Kit P.N , P.N , and P.N

CO2 Tank Conversion Kit P.N , P.N , and P.N Foodservice Group Multiplex Beverage Equipment Installation Instructions for CO2 Tank Conversion Kit P.N. 002247, P.N. 0022505, and P.N. 0025099 Introduction The following instructions cover the installation

More information

Model VR6 System. Installation, Operation & Maintenance

Model VR6 System. Installation, Operation & Maintenance Model VR6 System Installation, Operation & Maintenance General: All Archer Instruments chlorination systems are carefully designed and tested for years of safe, accurate field service. All Archer Instruments

More information

Assembly Instructions. -Cantilever Boat Lifts

Assembly Instructions. -Cantilever Boat Lifts Assembly Instructions -Cantilever Boat Lifts Winch Instruction Page Safety Information 1. The winch is built for the multipurpose of hauling and lifting operations. It is not to be used as a hoist for

More information

Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0)

Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW. Tel +44 (0) Allspeeds Ltd. Royal Works, Atlas St Clayton le Moors Accrington Lancashire England BB5 5LW Tel +44 (0)1254 615100 www.allspeeds.co.uk HP690A Intensifier Panel including the following versions: Model Intensification

More information

SHEET 2: VERTICAL INSTALLATION

SHEET 2: VERTICAL INSTALLATION IMAGE OW1291 OW1293 OW1295 OW1297 AVATAR OW1301 OW1303 OW1305 OW1307 OW1311 OW1313 OW1315 OW1317 OW1331 OW1333 OW1335 OW1337 SHEET 2: VERTICAL INSTALLATION SHEET 3: HORIZONTAL INSTALLATION Drawing: 760883XX

More information

LRS(H)4 Pressure-Reducing Regulator User Manual

LRS(H)4 Pressure-Reducing Regulator User Manual LRS(H)4 Pressure-Reducing Regulator User Manual Read the complete manual before installing and using the regulator. 2 Safe Product Selection When selecting a product, the total system design must be considered

More information

2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions

2012-June-12 SECOND DRAFT Hobie Getaway Spinnaker Installation Instructions SECTION A: INTRODUCTION This unofficial set of installation instructions was written for a 2009 Hobie Getaway, using a 2012 Hobie Spinnaker Kit 20999020. Note from the Author: I had never seen this kit

More information

Parts List. Description. Additional Considerations. Installation Instructions. Dual/Elite Hydraulic Treadmill Kit (supplied by EPI)

Parts List. Description. Additional Considerations. Installation Instructions. Dual/Elite Hydraulic Treadmill Kit (supplied by EPI) Page 1 of 9 Parts List Dual/Elite Hydraulic Treadmill Kit (supplied by EPI) Qty Description Treadmill Body 1 Treadmill Power Unit (per Treadmill Body) 2 Treadmill Decks (per Treadmill Body) 1 Treadmill

More information

STATIONARY TRUCK INTERNAL HALYARD CAM CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL COMMERCIAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING

STATIONARY TRUCK INTERNAL HALYARD CAM CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL COMMERCIAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING 9390 South 300 West, Sandy, Utah 84070 801-562-0123 800-782-0500 ColonialFlag.com STATIONARY TRUCK INTERNAL HALYARD CAM CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL COMMERCIAL INSTALLATION READ ALL INSTRUCTIONS

More information

TOYOTA TACOMA 2005 TOW HITCH Preparation. Part Number: PT

TOYOTA TACOMA 2005 TOW HITCH Preparation. Part Number: PT Preparation Part Number: PT791 04050 Kit Contents 1 1 Hitch Center Section 2 1 LH Frame bracket 1 RH Frame Bracket 4 2 Auxiliary Bracket Hardware Bag Contents 1 6 Hex Head Bolt, M12 x 1.2 (black) 2 6 Nut,

More information

HP10168 & HP10169 KITS HP10152 / HP10154 / HP10156

HP10168 & HP10169 KITS HP10152 / HP10154 / HP10156 HP10168/&HP10154 HP10169/KITS HP10152 HP10156 HP10152: 2" AMP Air Suspension Spacer Kit Ford F-450 Pickup 2WD & 4WD HP10154: 4" AMP Air Suspension Spacer Kit Ford F-450 Pickup 2WD & 4WD HP10156: 6" AMP

More information

Rudder Kit Assembly Instructions for Quest 13

Rudder Kit Assembly Instructions for Quest 13 Rudder Kit Assembly Instructions for Quest 13 Revised 4/2/2015 78501 Rudder System The Hobie Quest is designed for the addition of an optional rudder system. Rudder systems in boats like this allow you

More information

Preferred Instruments Danbury, CT USA

Preferred Instruments Danbury, CT USA Tank Level Sensor Model TG-EL-WF-xx Installation & Operation Instructions SDI-TG-EL-WF March 6, 2006 Preferred Instruments Danbury, CT USA www.preferredinstruments.com CONTENTS Installation Pg. 2 Calibration

More information

Pressure Dump Valve Service Kit for Series 3000 Units

Pressure Dump Valve Service Kit for Series 3000 Units Instruction Sheet Pressure Dump Valve Service Kit for Series 000 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00, 400, 500, and 700 applicator

More information

S110 Steel Level Panel Installation Instructions

S110 Steel Level Panel Installation Instructions S110 Steel Level Panel Installation Instructions NOTE: Fairway Architectural Railing Solutions will not be held liable for incorrect or unsafe installations by installer. It is the installer s resposibility

More information

830 SureFlo Soap Systems Installation Instructions. Foam Soap Cabinet... Pages 2-9 Liquid Soap Cabinet... Pages 10-19

830 SureFlo Soap Systems Installation Instructions. Foam Soap Cabinet... Pages 2-9 Liquid Soap Cabinet... Pages 10-19 830 SureFlo Soap Systems Installation Instructions Foam Soap Cabinet... Pages 2-9 Liquid Soap Cabinet... Pages 10-19 INSTALLATION INSTRUCTIONS SureFlo SOAP DISPENSING SYSTEM FOAM VERSION ONLY B-830 Foam

More information

! WARNING. Model PFC-1-G (direct acting) PFC-1-GR (reverse acting) Modulating Pneumatic Liquid Level Controls INSTRUCTION MANUAL MM-110B

! WARNING. Model PFC-1-G (direct acting) PFC-1-GR (reverse acting) Modulating Pneumatic Liquid Level Controls INSTRUCTION MANUAL MM-110B INSTRUCTION MANUAL MM-110B Model PFC-1-G (direct acting) PFC-1-GR (reverse acting) Modulating Pneumatic Liquid Level Controls APPLICATIONS: Use with other pneumatic devices, for liquid level sensing in

More information

Side-of-Pole Mount for 1 Module (SPM1) For Module Type C

Side-of-Pole Mount for 1 Module (SPM1) For Module Type C Module Type Width Length C 22-27 56-63 Side-of-Pole Mount for 1 Module (SPM1) For Module Type C ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A PCN 022212-1 Side-of-Pole Mount

More information

Ref Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket

Ref Part Part # Qty Letter A Rudder Catcher B X 1/2 PH Bolts C Rudder Bracket Ref Part Part # Qty A Rudder Catcher 07.2694.0000 1 J B Q A B 10-32 X 1/2 PH Bolts 07.2136.0000 10 C Rudder Bracket 07.2689.0000 1 D Kayak Pad Eye 01.1315.0430 2 E Cherry Rivets 01.1315.0459 4 H T N P

More information

Backboard and Rim Owners Manual

Backboard and Rim Owners Manual REQUIRED TOOLS AND MATERIALS: Two (2) Capable Adults Tape Measure Backboard and Rim Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. Step Ladder - 8ft. (2.4

More information

EZ-Mount 4 Spring Enclosed System to 22 (Low & High Mount Applications) Installation Instructions

EZ-Mount 4 Spring Enclosed System to 22 (Low & High Mount Applications) Installation Instructions 501-1768 (With Wire) 501-1769 (No Wire) 501-1766 (With Wire) 501-1767 (No Wire) 607-015 WLH 06/20/18 TABLE OF CONTENTS ***Assembly*** ***Parts*** Pivot Points and Mounting Locations (Low Mount)... 1 High

More information

VISIT THE LIFETIME WEB SITE: **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, COPY

VISIT THE LIFETIME WEB SITE:   **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, COPY 01/28/2011 VISIT THE LIFETIME WEB SITE: WWW.LIFETIME.COM **U.S. and Canada customers ONLY** IF ASSISTANCE IS NEEDED, DO NOT CONTACT THE STORE!!! CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865

More information

Tread Brake Assembly Instructions

Tread Brake Assembly Instructions reated: 9/06/202, Revision: 2/20/204 Tread rake ssembly Instructions Table of ontents: Lower rake omponents..2-4 able rake ssembly: rake Handle omponents..5-7 able ssembly....8 Tee Handle rake ssembly...9-0

More information

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , )

VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns , , , , , ) VL 2K LIFT D-L WINCH INSTRUCTIONS (Applies to P/Ns 3714022, 3714028, 3714034, 3714040, 3714043, 3714046) REIMANN & GEORGER CORPORATION MARINE PRODUCTS BUFFALO, NY P/N 6112103 04/09/18 1 SAFETY 1.1 INTRODUCTION

More information

Installation Guide RHT-380. This Manual Must Be Read Before Operating The Equipment CUSTOMER COPY

Installation Guide RHT-380. This Manual Must Be Read Before Operating The Equipment CUSTOMER COPY Installation Guide This Manual Must Be Read Before Operating The Equipment RHT-380 Madison Heights, Michigan 48071 800-725-8377 www.snowexproducts.com CUSTOMER COPY Trynex International 2013 (REV B) F50767

More information

(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION)

(PLEASE CONTACT YOUR LOCAL DEALER or CUSTOMER SERVICE FOR WARRANTY INFORMATION) RUDDER KIT SOLO AND TANDEM KAYAKS IMPORTANT: For Tandem kayaks, the Supplemental Kit will be needed in addition to this kit and can be purchased through a registered dealer. The addition of a rudder to

More information

BASIN AND WALL MIXER INSTALLATION INSTRUCTIONS

BASIN AND WALL MIXER INSTALLATION INSTRUCTIONS BASIN AND WALL MIXER INSTALLATION INSTRUCTIONS IMPORTANT INFORMATION IMPORTANT All tapware and showers to be installed by a licensed plumber and to Australian Standards. Fit tempering and pressure reduction

More information

Series RT Spring Driven Hose Reels Operating Instructions

Series RT Spring Driven Hose Reels Operating Instructions Series RT Patent No. 7, 150, 425 Series RT Spring Driven Hose Reels Operating Instructions Thank you for purchasing a Reelcraft product. We wish you success in the critical function it will provide you

More information

MODEL TRIPEX PULLEY SYSTEM

MODEL TRIPEX PULLEY SYSTEM MODEL 922184 TRIPEX PULLEY SYSTEM 1 PARTS LIST FOR TRIPEX PULLEY SYSTEM Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your

More information

SERVICE KITS SPECIFICATIONS GENERAL DESCRIPTION. y Use only genuine ARO replacement parts to assure compatible. RM051S-XXX-XX Single Post Lift / Ram

SERVICE KITS SPECIFICATIONS GENERAL DESCRIPTION. y Use only genuine ARO replacement parts to assure compatible. RM051S-XXX-XX Single Post Lift / Ram OPERATOR S MANUAL INCLUDING: OPERATION, INSTALLATION AND MAINTENANCE. INCLUDE MANUALS: S-635 General Information (pn 97999-635). RM051S-XXX-XX RM051S-XXX-XX SINGLE POST LIFT / RAM For use with 5 gallon

More information

STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING

STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE PROCEEDING 9390 South 300 West, Sandy, Utah 84070 801-562-0123 800-782-0500 ColonialFlag.com STATIONARY TRUCK INTERNAL HALYARD V-CLEAT FLAGPOLES FOR QUICK AND PROFESSIONAL INSTALLATION READ ALL INSTRUCTIONS BEFORE

More information

OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL)

OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) OWNER'S MANUAL LOCK-N-LOAD BULLET FEEDER (PISTOL) Table of Contents ASSEMBLY ASSEMBLY Pistol Bullet Feeder... Page 3 CHANGE-OVERS The Hornady Lock-N-Load Pistol Bullet Feeder is capable of feeding most

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS KIT CONTENTS: PART NUMBER: DESCRIPTION: E361SXA300 ROOF MOUNT BICYCLE CARRIER B9 TRIBECA Short Carriage Bolt Long Carriage Bolt 3x Over-Molded Wrench Button Head Screw 2x Washer

More information

SERVICE KITS SPECIFICATIONS GENERAL DESCRIPTION. RM052S-XXX-XX Two Post Lift / Ram

SERVICE KITS SPECIFICATIONS GENERAL DESCRIPTION. RM052S-XXX-XX Two Post Lift / Ram OPERATOR S MANUAL INCLUDING: OPERATION, INSTALLATION AND MAINTENANCE. INCLUDE MANUALS: S-635 General Information (pn 97999-635). RM052S-XXX-XX RM052S-XXX-XX TWO POST LIFT / RAM For use with 5 gallon /

More information

RM052S-XXX-XX TWO POST LIFT / RAM

RM052S-XXX-XX TWO POST LIFT / RAM OPERATOR S MANUAL INCLUDING: OPERATION, INSTALLATION AND MAINTENANCE. INCLUDE MANUALS: S-635 General Information (pn 97999-635). INGERSOLL RAND COMPANY LTD 209 NORTH MAIN STREET BRYAN, OHIO 43506 (800)

More information

Installation and Training Manual

Installation and Training Manual AirForce1 Tower Kit Installation and Training Manual FuturEnergy Limited Ettington Park Business Centre Stratford upon Avon CV37 8BT +44 (0)1789 451070 Table of Contents Safety Notes... 3 Parts Supplied

More information

FNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions

FNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions FNFB-30 (30 FT FIELDPRO FOOTBALL BACKSTOP SYSTEM) Installation Instructions Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev: - Page

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS KIT CONTENTS: INSTALLATION INSTRUCTIONS PART NUMBER: DESCRIPTION: E361SXA302 roof MOUNT BICycle CARRIER SINGLE Short Carriage Bolt 1x Long Carriage Bolt 3x Over-Molded Wrench 1x Button Head Screw 2x Washer

More information

THOR 10 HAMMER CAGE INSTRUCTIONS

THOR 10 HAMMER CAGE INSTRUCTIONS 75 " 7m 78 4" m 6" 8.8m 45 ".70m 4.9deg 6 4" 6m 44 4".67m 75 " 7m 9 4" 0m 44".m 497 4".64m The 70, Thor Hammer Cage, consists of four heavy duty aluminum net poles. The unique pole structure reduces the

More information

BARRIER OFFSET 0" A 6" 6" A 12" 12" A 26" A 26" 3A OR 4A L OR S * ** L OR S L OR S

BARRIER OFFSET 0 A 6 6 A 12 12 A 26 A 26 3A OR 4A L OR S * ** L OR S L OR S ACCEPTABLE (TCB) TYPES AND ANCHORING DETAILS BASED ON UNDERLYING SURFACE TYPE AND BARRIER OFFSET FROM DROP-OFF BARRIER OFFSET UNDERLYING SURFACE 0" A 6" 6" A 12" 12" A 26" A 26" TCB TYPE DETAIL TCB TYPE

More information

-- SGP (NOVA TEAM SQUARE)

-- SGP (NOVA TEAM SQUARE) -- SGP-100 -- (NOVA TEAM SQUARE) Installation Instructions Call Jaypro Sports Equipment at 1-800-243-0533 during regular business hours for technical support. www.jaypro.com Rev-B Page 1 of 9 JAYPRO SPORTS

More information

Beach Dolly with cradle & keel pad Assembly Instructions

Beach Dolly with cradle & keel pad Assembly Instructions Beach Dolly with cradle & keel pad Assembly Instructions H G B A D C I J L F PART NAME QTY A. AXLE... 1 with tongue bracket and cradle supports attached B. CRADLE SUPPORT BAR... 2 C. TONGUE... 1 D. TONGUE

More information

Retractable Hose Reel with 3/8" x 50' PVC Hose

Retractable Hose Reel with 3/8 x 50' PVC Hose Retractable Hose Reel with 3/8" x 50' PVC Hose Item# 4816153 Owner s Manual Assembly and Operation Instructions MADE IN CHINA Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before

More information

Installation Instructions - Steel 4 Spring Arm Kits , , , ,

Installation Instructions - Steel 4 Spring Arm Kits , , , , Installation Instructions - Steel Spring Arm Kits 50-0709, 50-079, 50-0750, 50-075, 50-078 GR 8// 07-00 0 N. Marshall Ave. El Cajon CA. 900 For technical support call us at (800) 8-075 Step. Determining

More information

Anti-flood device Model B-1

Anti-flood device Model B-1 December 4, 2009 Dry Systems 123a 1. DESCRIPTION The Anti-flood Device is required when Viking accelerators are installed on dry systems according to Viking Model E-1 Accelerator Trim Charts. In the SET

More information

WHEATLEY WHEATLEY SERIES 500 SWING CHECK VALVE. Installation, Operation and Maintenance Manual

WHEATLEY WHEATLEY SERIES 500 SWING CHECK VALVE. Installation, Operation and Maintenance Manual WHEATLEY SERIES 500 SWING CHECK VALVE STANDARD INTEGRAL SEAT & OPTIONAL REMOVABLE SEAT 2" FP - 6" FP 150# - 1500# 8" FP - 12" FP 150# - 900# API 6D and B16.34 2" FP - 4" FP 5000# DRILLING PRODUCTION VALVE

More information

MODEL CHEST PULLEY SYSTEM

MODEL CHEST PULLEY SYSTEM MODEL 9180 CHEST PULLEY SYSTEM 1 PARTS LIST FOR CHEST PULLEY Note: Check with your architect or a professional contractor for hardware required to attach the unit to the wall and floor in your facility.

More information

400/488 Rotating Davit Installation Instructions

400/488 Rotating Davit Installation Instructions 400/488 Rotating Davit Installation Instructions These instructions were written with the owner in mind. If you are the installer make sure these instructions are passed along to the owner of the boat.

More information

General Information. Installation Instructions. CP1000 & FCP1000 Folding Markers. Used with: CP1000 FCP1000

General Information. Installation Instructions. CP1000 & FCP1000 Folding Markers. Used with: CP1000 FCP1000 Installation Instructions CP1000 & FCP1000 Folding Markers Used with: CP1000 FCP1000! When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life

More information

RUDDER KIT INSTRUCTIONS

RUDDER KIT INSTRUCTIONS C I N S T R U C T I O N S RUDDER KIT INSTRUCTIONS PAMLICOS-0,0,T, T, 60T, Excel Rotomolded Pamlico 0, 0, T, T, 60T, Excel The addition of a rudder to a kayak results in additional control and efficiency,

More information

Air Intake Snorkel Kit

Air Intake Snorkel Kit SSV KIT - Air Intake Snorkel Kit Part number (SKU) : 715003733 Product: Side-by-side Project no: 487802499 Instruction Sheet P/N: 487802499 Revision no: Revision date: Item covered: Air Intake Snorkel

More information

ATD /8 x 50 Retractable Air Hose Reel Owner s Manual

ATD /8 x 50 Retractable Air Hose Reel Owner s Manual ATD-31166 3/8 x 50 Retractable Air Hose Reel Owner s Manual Features Heavy-gauge, all-steel reel assembly 8-position ratchet mechanism locks reel at desired hose length 5-position adjustable roller outlet

More information

UNITY 2. Uni-DAAMS Manual. Version 1.3 (Changes to Section 1.1) March 2010

UNITY 2. Uni-DAAMS Manual. Version 1.3 (Changes to Section 1.1) March 2010 UNITY 2 Uni-DAAMS Manual Version 1.3 (Changes to Section 1.1) March 2010 1. Introduction...2 1.1. Installing the DAAMS tube ovens...2 1.2. Swapping between tube types...5 1.3. Changing tube oven o-rings...6

More information

FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions

FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions FIRST TEAM SPORTS, INC Storm Portable Series Assembly Instructions WARNING! WARNING! WARNING! THIS BASKETBALL SYSTEM IS SPRING LOADED AND SHIPPED UNDER TENSION. ATTEMPTING TO ASSEMBLE OR DISASSEMBLE ANY

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Accessory P/N 08L07-E09-100 Application 2013 ODYSSEY Publications No. AII 13265 Issue Date AUG 2012 Put this information in the glove box with the vehicle owner s manual. PARTS

More information

Ersatzteilliste. Düsenwagen R 30

Ersatzteilliste. Düsenwagen R 30 Ersatzteilliste Düsenwagen R 30 Beinlich Agrarpumpen und maschinen GmbH Eifel-Maar-Park 16 D 56766 Ulmen Tel.: 02676 9516-0 - Fax: 02676 951615 www.beinlich-beregnung.de info@beinlich-beregnung.de Beinlich

More information

Hose Reel Instruction Manual

Hose Reel Instruction Manual Instruction Manual Technical Data Item Inlet/Outlet (Fitting) Max Pressure (psi/bar) Hose Capacity I.D.(inch) Max Length(ft/m) L5 /4 300/0 /4 50/5 L53 3/8 300/0 3/8 50/5 L54 / 300/0 / 50/5 M5 /4 750/89

More information

RD(H)20/25 Pressure-Reducing Regulator User Manual

RD(H)20/25 Pressure-Reducing Regulator User Manual RD(H)20/25 Pressure-Reducing Regulator User Manual Read the complete manual before installing and using the regulator. 2 Safe Product Selection When selecting a product, the total system design must be

More information

IMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION

IMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION IMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION This Fitting Guide is designed to assist in the Installation of your Reverse Osmosis System. Some of the parts that are supplied with each system may

More information

Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation

Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS. step-by-step assembly and installation Side-of-Pole Mount for 1 Modules (SPM1) For Module Types E, F, G, & H ASSEMBLY INSTRUCTIONS step-by-step assembly and installation Version 1, Rev A SP3348-1 PCN 022212-2 Side-of-Pole Mount for 1 Module

More information

SIGNATURE DEF REELS Models: Bare Reel Reel Reel Reel

SIGNATURE DEF REELS Models: Bare Reel Reel Reel Reel SERVICE BULLETIN SB2023 Rev C 7/11 SIGNATURE DEF REELS Models: 2400-006 Bare Reel 2400-007 16 Reel 2400-008 20 Reel 2400-009 30 Reel Thoroughly read and understand this manual before installing, operating

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS SureFlo Soap Dispensing System Bobrick SureFlo Soap Dispensing System Soap Cabinets, Soap Dispensers and connections are available from all Bobrick Distributors. Bobrick SureFlo

More information

GT21 String Trimmer UT Page 1 of 16 Accessories

GT21 String Trimmer UT Page 1 of 16 Accessories GT21 String Trimmer UT-26038 Page 1 of 16 Accessories GT21 String Trimmer UT-26038 Page 2 of 16 Accessories Ref # Part Number Qty S/P/F Description 1 PS01443 1 TOOL KIT 2 DG07819 1 /P STRAP 3 G07830 1

More information

Steel Spring Driven Reel Instruction Manual

Steel Spring Driven Reel Instruction Manual Steel Spring Driven Reel Instruction Manual WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in

More information

LV LOADER DIRECTIONAL CONTROL VALVES INSTALLATION & USER GUIDE

LV LOADER DIRECTIONAL CONTROL VALVES INSTALLATION & USER GUIDE LV LOADER DIRECTIONAL CONTROL VALVES INSTALLATION & USER GUIDE SPECIFICATIONS: 10 gpm (38 lpm) Nominal Capacity. Rated up to 4000 psi (275 bar). Port Sizes-Inlet/Outlet #8SAE (3/4-16). Work Ports #8SAE

More information

Boat Boat Loader Fitting Instructions

Boat Boat Loader Fitting Instructions Aerodynamic & Heavy Duty Roof Rack Systems Australian Made - Australian Owned www.rhinorack.com Boat Boat Loader Fitting Instructions CONTROLLED Balance point 3 Front eye nuts position 3 Transom eye nut

More information

Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS

Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS 1 Stand-N-Fish FULL DETAIL INSTALLATION INSTRUCTIONS Thank you for purchasing the incredible new Stand-N-Fish Kayak Fishing System. Once installed on your kayak the Stand-N-Fish will take your kayak fishing

More information

Paintball Marker. User s Manual. 530 South Springbrook Road Newberg, OR 97132

Paintball Marker. User s Manual. 530 South Springbrook Road Newberg, OR 97132 Paintball Marker User s Manual 530 South Springbrook Road Newberg, OR 97132 Component Concepts, Inc., 530 South Springbrook Road, Newberg, OR 97132 Phone: (503) 554-8095 Fax: (503) 554-9370 www.phantomonline.com

More information

Pre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender

Pre-Paint>Fuselage>Empennage>Fit vertical tail fin. Objectives of this task: Materials and equipment required: Fit the spar extender Pre-Paint>Fuselage>Empennage>Fit vertical tail fin Objectives of this task: To fit the vertical tail fin to the fuselage, including fitting the static probe, static tube, optional strobe light wiring and

More information

MUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3.

MUELLER A A Non-Adjustable. Vertical Indicator Posts. Reliable Connections. General Information 2. Technical Data 3. Installation Instructions manual MUELLER table of contents PAGE A-20808 General Information 2 Technical Data 3 Dimensions 4 A-20809 Non-Adjustable Installation 5-6 Parts 7 Maintenance 8 Vertical Indicator

More information

TECHNICAL DATA. Page 1 of 12

TECHNICAL DATA. Page 1 of 12 Page 1 of 12 1. DESCRIPTION The Viking Regulating Valve is a direct-acting, single-seated, spring-loaded diaphragm valve. When installed as a pilot regulating valve on a Viking Model H or J Flow Control

More information

V-PLOW. ACCUFLO Conveyor Belt Cleaning System MAX SYSTEMS GUIDE. Engineering. LIB-CP-SYS-01-E Rev.9. Page 1

V-PLOW. ACCUFLO Conveyor Belt Cleaning System MAX SYSTEMS GUIDE. Engineering. LIB-CP-SYS-01-E Rev.9. Page 1 ACCUFLO Conveyor Belt Cleaning System Page 1 Conveyor Belt Cleaning System - System Nomenclature CATGORY MAINFRAM INFORMATION BLAD INFORMATION CP=CONVYOR PRODUCTS CP - PA - 36 M - G 83 SYSTM TYP BLT WIDTH

More information