Build Your Own Flamethrower Step-by-step Manual
|
|
- Margery Collins
- 5 years ago
- Views:
Transcription
1 Build Your Own Flamethrower Step-by-step Manual Table of Contents: Parts List.. page 1 Operation...page 6 Diagrams. pages 7-9 Parts list: Required: Air tank (large) Pressure washer gun with high-pressure hose CO 2 tank (small) 320 CGA Female to 1/8 NPT 1 Female Adapter 1/8 male NPT to 1/8 male NPT (4 in length) Paintball ASA 7/16 drill bit Pipe tap 1/4"-18 NPT Gun oil, 2 stoke oil, or similar lubricant 1/4 hose slip fitting to 1/4 male threads (see image) Teflon tape Short hose clamps 4 minimum (2) Propane cylinder (preferably 14.1 oz) Welding Torch Long Hose clamps: 12 minimum (3) NOTE: The following instructions are for ACADEMIC USE ONLY! Do NOT attempt to build. Extreme injury or death can occur. The author(s) of this manual accept NO responsibility for ANY injury or damages to people, animals, or property. 1 National Pipe Thread 1
2 Gathering Your Parts: Air Tank (large) The large air tank is to your flamethrower what your gas tank is to your car. It is the holding tank for whatever liquid you will be shooting. The tank used in this build was an aluminum 15lb 2 CO 2 tank used for soda machines and beer kegs. A 20lb tank (about $15 more) will work equally as well and will provide more volume and longer firing time. If you do not know the size of your tank, you can figure it out by measuring the height from the top of the tank (not including the regulator/valve) to the base. Height will be 24 for both a 20lb and 15lb tank. The base diameter of a 15lb tank is 7 and for a 20lb tank is 8. A height shorter than 24 indicates a tank smaller than 15lbs. The 15lb tank holds approximately 2.5 gallons of liquid and will shoot for a total time of about 40 seconds. A 20lb tank will shoot closer to 1 minute. The handle on the top of the tank needs to be removed so there is room to attach the fitting that leads to the CO 2 tank. A c-clip is the only thing holding on the handle. Using c-clip pliers and possibly a flat head screwdriver, you should be able to remove it with little difficulty. These tanks come equipped with 320 CGA male threads that will need to be reduced (see next step) to attach the small CO 2 tank. 15lb and 20lb tanks available at BeverageFactory.com for $95.50 and $ respectively. This tank is recommended since theses instructions provide the parts to reduce the included fitting. If this link ever goes dead, a simple search will provide many alternatives. 320 CGA Female to 1/8 NPT Female Adapter The fitting on the tank will need to be reduced in order to attach either the CO 2 tank or compressed air tank. Simply layer the male 320 CGA CO 2 threads with 3 passes of Teflon tape. 2 The lb rating is the volume measurement for CO 2 and Nitrogen. Unlike scuba tanks, cubic feet is not used for measurement. A 15lb tank holds approximately 2.5 gallons. 2
3 Attach the adapter and tighten the adapter using a wrench or pliers. 1/8 Male NPT to 1/8 Male NPT (4 in length) This is a simple 1/4 diameter pipe with 1/8 NPT male threads on both ends and is used as an extension. 4 is needed to provide adequate space so the small CO 2 tank will stand vertically without touching the large one. Wrap both sides of the pipe with 1-2 passes of Teflon tape. Tighten this pipe using pliers gripped on the middle of the pipe (not the threads!). Paintball ASA This is used to attach the small CO 2 tank to the 1/8 NPT pipe. Attach to the other end of the 1/8 NPT pipe. Not all ASAs will look like the picture provided (image at right). Virtually all ASAs for paintball use will work. This piece is used to apply pressure to the nipple valve on the small CO 2 tank, letting the compressed gas pressurize the system. Available at most all paintball stores for about $15 or do a search on the web for Paintball ASA. CO 2 Tank (Small) This tank is what provides the pressure for projecting the liquid. A 20 oz CO 2 tank, commonly used for paintball guns, is recommended to ensure enough pressure is provided to maintain a consistent shot. This CO 2 tank will put out between psi 3 depending on temperature and how full the tank is. Here are general guidelines for pressure output based on temperature (assuming outside temperature and tank temperature are equal). The tank is rated for 1800psi and the hose for over 2000psi so over pressurizing the system will not be an issue. This tank will attach at the ASA. 100 F = 1200psi 4 80 F = 950psi 60 F = 700psi A 20oz CO 2 tank is available in any paintball store as well as most sporting goods stores such at Sport Chalet for around $ Pipe Tap 1/4"-18 NPT and 7/16 Drill Bit Since your CO 2 tank will not have a hole to attach the pressure washer hose, you will need to make your own. Drill a 7/16 hole on the side of the tank, 2 from the bottom of the tank to avoid drilling into the 3 Pounds per square inch 4 All pressure ratings are approximations based on temperature. Other factors such as elevation, humidity, and barometric pressure can affect pressure. 3
4 base (right image). Once the hole is drilled, you need to cut the threads. To properly cut the threads, you will need some kind of lubricant such as gun oil or motor oil to disperse heat and ensure smooth and complete threads are cut. Using the 1/4"-18 NPT tap with the tap and die kit (see image below) begin cutting the threads slowly by inserting the tap into the hole and turning clockwise 1/8-1/4 of a turn then backing out the tap slightly to allow the cut metal shards to clear the newly cut grooves. Lubricate often. Cut using the entire length of the tap to ensure the grooves are properly cut. Once the whole is drilled and tapped, rinse out the tank with water to remove the metal shards. Tap and die kits can be found at most major hardware stores. When purchasing, be sure the tap is for NPT threads since there are other sizes available. Even though we are using a 1/4 tap, you may notice that the diameter of the tap is 1/2. We know this, there is no typing error, it is just the way the NPT threads are measured. 1/4 Hose Slip Fitting to 1/4 Male Threads NPT Once the hole is cut, cover the threads of the hose fitting with 2 passes of Teflon tape and thread into the hole. Tighten using a 9/16 wrench. This Husky 1/4 hose repair kit (right image) includes the necessary fitting and hose clamps. The doublesided slip fitting will not be used. This kit can be found at Home Depot or other hardware stores for under $4. Pressure Washer Gun with High-Pressure Hose The gun of this flamethrower is the same gun that is used with a pressure washer. It s important that a pressure washer gun is used since most have metal internals that won t corrode (like plastic will) upon contact with the fuel. A pressure-washer gun can be purchased 4
5 usually with the high-pressure hose included at most major hardware stores or on the web for around $ One end of the high-pressure hose will attach to the pressure washer gun; the other end will be set up to attach to the pressure washer. A pressure washer is not being used for this build so cut that end off so the hose is the desired length (6 was used for this build). Push the hose onto the 1/4 hose fitting (if this is difficult, soak the end of the hose in boiling water for about 10 seconds to soften it) on the side of the tank and secure it using 2 of the included small hose clamps. Be sure to use both for extra strength. Propane Cylinder To light the fuel, you will need a source of ignition. The best way to light a stream of flammable liquid is with a pilot flame. The propane cylinder we used was a 14.1oz propane tank and is recommended for it s long and slender size. Bernzomatic makes a great quality tank and is what was used for this build. Available for around $4-5 at any hardware store Propane was used for this build but any flammable gas such as map gas will suffice. Welding Torch The welding torch used for this build was the Bernzomatic JTH7 Welding Torch with 4 flexible hose. Another torch may be used as long as it can be positioned under the pressure washer gun to provide a pilot flame. The soft hose is a key asset to this task. Three 12 hose clamps are needed to secure the propane cylinder and torch to the pressure washer gun (see diagram). This torch available at most major hardware stores such as Home Depot or Harbor Freight for around $20. Also may be purchased on the web. 5
6 Operation: NOTE: The authors of this manual do not take responsibility for ANY consequences due to use or misuse of this flamethrower. 1) Begin by removing the top of the large CO 2 tank. The entire top piece, which includes the 320 male threads, should unscrew relatively easily. Leverage tools may be applied if you cannot unscrew with your hands. Fill the entire volume of the tank with the desired liquid or fuel. 2) Once filled, seal the large tank with the same piece that was removed. Ensure that the o-ring at the base of the threads is in good condition before each use. Tighten snugly; hand tightening should be enough if you use the ASA as a fulcrum for leverage. Ensure that the on/off valve on the top of the large tank is closed (turned clockwise) before attaching the small CO 2 tank. 3) Attach the small CO 2 tank at the ASA until you hear the gas fill the fittings. The tank will be considerably more difficult to tighten at this point. 4) Open the on/off valve on the top of the large tank slowly. You will hear the gas filling what space is left in the large tank. 5) Turn on the pilot flame. Open the valve to the propane tank and light the flame using a spark or other fire source. 6) At this point your flamethrower is ready for use. Do not shoot at people or animals! 7) After the liquid has been depleted from the tank, turn of the pilot flame and close the on/off valve by turning it counter clockwise until it stops. Remove the CO 2 tank from the ASA. A small amount of gas may escape while you are unscrewing the tank. The tank will be very cold from the CO 2 expansion. The range of this flamethrower is approximately 45 feet. 6
7 7
8 8
9 9
Freedom8 ShoeBox Compressor Manual
Freedom8 ShoeBox Compressor Manual Warning!! This product is not a toy! Use or misuse can cause severe injury or death! Use only with adult supervision. This unit is only to be used with tanks, hoses and
More informationV-24 OXYGEN LANCE VALVE
INSTRUCTIONS for F-4737-U May, 2009 V-24 OXYGEN LANCE VALVE w/ C -Size Inlet w/ B -Size Inlet V-24 Oxygen Lance with 1/8" Pipe Holder... 9728D65... 2218939 V-24 Oxygen Lance with 1/4" Pipe Holder... 9728A65...
More informationASSEMBLY & USE MANUAL
DRAFT BEER DISPENSER ASSEMBLY & USE MANUAL - Stout Beers SAFETY FIRST! Read instructions completely Mixed gas can be dangerous. Flush chemical out of beer hose completely before re-tapping keg. Micro Matic
More informationLITTLE MAX MODEL 50G 50,000 BTU PROPANE TORCH
LITTLE MAX MODEL 50G 50,000 BTU PROPANE TORCH INSTRUCTION MANUAL MODEL 50G PROPANE TORCH ASSEMBLY, TESTING, AND OPERATING INSTRUCTIONS PLEASE READ AND RETAIN THIS INFORMATION FOR FUTURE REFERENCE DO NOT
More informationFOR INSTALLING CO 2 BLENDER KIT (P/N IN BEER SYSTEM
IMI CORNELIUS INC One Cornelius Place Anoka, MN 55303-623 Telephone (800) 238-3600 Facsimile (612) 22-326 INSTALLATION INSTRUCTIONS FOR INSTALLING CO 2 BLENDER KIT (P/N 111612000 IN BEER SYSTEM SECONDARY
More informationPlay Safe. Safety. Instruction Manual. Warning. Rebel Specifications
Operation Guide Instruction Manual Congratulations on your purchase of the 32 Degrees Rebel Xtreme semi-auto. Before you use this marker, please read this manual in its entirety. Please follow all safety
More informationOXYGEN ACETYLENE WELDING & CUTTING EQUIPMENT
OXYGEN ACETYLENE WELDING & CUTTING EQUIPMENT Introduction: The oxy-acetylene torch can be used for various tasks. It can be used for cutting steel, welding steel, brazing and for heating metal. The oxy-acetylene
More informationSUMMITTM 400 & 600. Natural Gas Barbecues. Step-By-Step Guide
SUMMITTM 400 & 600 Natural Gas Barbecues Step-By-Step Guide W E B E R W E B E R W E B E R W E B E R Summit 400 NG Summit 600 NG CANADIAN GAS ASSOCIATION R A P P R O V E D WARNING: Follow all leak check
More informationInstruction Manual Updated 7/26/2011 Ver. 2.2
4-Unit Model MB HTHP Filter Press #171-50-4: 115-Volt #171-51-4: 230-Volt Instruction Manual Updated 7/26/2011 Ver. 2.2 OFI Testing Equipment, Inc. 11302 Steeplecrest Dr. Houston, Texas 77065 U.S.A. Tele:
More informationATD LB PRESSURE BLASTER INSTRUCTION MANUAL
ATD-8402 90LB PRESSURE BLASTER INSTRUCTION MANUAL SAVE THESE INSTRUCTIONS SAFETY INSTRUCTIONS FOR SANDBLASTER 1. Before opening the tank release the air pressure on the sand tank. To do this, turn off
More informationOperation Manual. Carbon Filtration Industrial Drive, Orlinda, TN fax
Operation Manual Carbon Filtration 615-654-4441 sales@specialtyh2o.com 615-654-4449 fax TABLE OF CONTENTS Section 1 GENERAL 1.1 Warnings and Cautions... 1 1.2 Theory of Operation... 2 1.3 System Illustration...
More information200 PSI COMPRESSORS - MODEL NUMBERS
200 PSI COMPRESSORS - MODEL NUMBERS 380C AIR COMPRESSOR KIT PART NO. 38033 480C AIR COMPRESSOR KIT PART NO. 48043 380C 480C IMPORTANT: It is essential that you and any other operator of this product read
More informationRG1200 Service and Repair Manual
Dive Rite RG 1200 Regulator Service and Repair Manual Page 1 Text and Photography by Pete Nawrocky Copyright ( ) 1999-2000, Lamartek, Inc., dba Dive Rite RG1200 Service and Repair Manual First Stage.........................................
More information100C Air Compressor Kit
10010 100C Air Compressor (standard mounting bracket, CE Spec) 10014 100C Air Compressor (no leader hose or check valve, CE Spec) 10016 100C Air Compressor (with Omega Bracket, CE Spec) IMPORTANT: It is
More informationUser Instruction Manual
User Instruction Manual 4500 psi Air Compressor Ver 2, 1.18 Contents Parts Included...3 Assembly Instructions...3-5 Operation Instructions...6-7 Oil Change Intervals...8 Air Filter Replacement...9 Setting
More informationHot Compressed Air Lance Operation Manual. LAB Manufacturing 9483 Reading Road Cincinnati, OH (800)
Hot Compressed Air Lance Operation Manual www.heatlances.com LAB Manufacturing 9483 Reading Road Cincinnati, OH 45215 (800) 776-5830 PARTS CHECK LIST NOTE: Check all fittings & connections prior to operation.
More informationSPECIFICATIONS Type: Twin stack, single phase Tank: 4 gallon Air Output: PSI; PSI Max PSI: 125 PSI HP: 1.
2 GALLON TWIN STACK AIR COMPRESSOR Model: 9526 DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service. CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or
More information420C AIR COMPRESSOR KIT PART NO C AIR COMPRESSOR KIT PART NO
420C AIR COMPRESSOR KIT PART NO. 42042 460C AIR COMPRESSOR KIT PART NO. 46043 420C 460C IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this
More informationSafe Work Instructions For Oxygen Acetylene Equipment
Safe Work Instructions For Oxygen Acetylene Equipment Policy Sponsor: Assistant Vice President Facilities Management Responsible Unit: Trade Services Approval Date: September 2010 Revisions: January 2018
More informationMAYHEM MAYHEM OWNERS MANUAL. Paintball Guns International. Manufactured by
MAYHEM MAYHEM OWNERS MANUAL Manufactured by Paintball Guns International Table of Contents Specifications...................... 2 Parts diagram and Listing............. 3 Description of Marker Operation.......
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More informationModel PSI Compressor with 3-Gallon Air Tank 12VDC
Model 6350 150 PSI Compressor with 3-Gallon Air Tank 12VDC IMPORTANT: It is essential that you and any other operator of this product read and understandd the contents of this manual before installing
More informationINSTALLATION & START-UP INSTRUCTIONS. Clack WS1 & WS1.25 METER WATER SOFTENER SYSTEMS
INSTALLATION & START-UP INSTRUCTIONS Clack WS1 & WS1.25 METER WATER SOFTENER SYSTEMS 1999-2009 QualityWaterForLess.com - 1 - info@qualitywaterforless.com Preface: Thank you for your purchase of a new Water
More information0 1,150 1/
π H-2030 shrinkfast heat gun #975 1-800-295-5510 uline.com general safety provisions Read this manual thoroughly to familiarize yourself with the parts and safe operation of this tool. Keep for future
More informationAluminum 13 cu tank Includes regulator Fill pressure: 3,000 psi (200 bar) Output: 1,100 psi +/- 10% (75bar)
Aluminum 13 cu tank Includes regulator Patent numbers: 6,851,447 7,059,343 7,051,751 Fill pressure: 3,000 psi (200 bar) Output: 1,100 psi +/- 10% (75bar) Contents Safety system... 3 Fill your tank... 4
More informationMAINTENANCE PROCEDURE FOR X 650
MAINTENANCE PROCEDURE FOR X 650 X 650 25. juli 2005-1/6 MAINTENANCE PROCEDURE FOR X 650 2 ND STAGE WARNING: This maintenance procedure is only for appointed Scubapro technicians that completed a course
More informationSECTION 2 RING MOUNT
SECTION 2 RING MOUNT Rotax aircraft engines are manufactured and supported by Rotax GmbH of Austria. Read and understand the Rotax manuals completely before starting with the engine installation, as they
More informationPARTS, SERVICE & REPAIR BULLETIN
WH4C PARTS, SERVICE & REPAIR BULLETIN 400 SERIES HEAVY DUTY WELDING HANDLE Manual No: 0056-3763 Issue Date: October 07, 03 Revision: AA VictorTechnologies.com Table of Contents SECTION : GENERAL SAFETY
More informationIMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION
IMPORTANT PLEASE READ BEFORE COMMENCING INSTALLATION This Fitting Guide is designed to assist in the Installation of your Reverse Osmosis System. Some of the parts that are supplied with each system may
More informationHot Tapping Machine. OPERATIONS MANUAL and OPERATING INSTRUCTIONS
262-2040 Hot Tapping Machine For performing 1/4 6 Hot taps 285 psi or less. Municipal Water, Sewage, & Building Services Use OPERATIONS MANUAL and OPERATING INSTRUCTIONS WARNING: These instructions are
More informationFITTINGS THREAD LUBRICANTS. Fittings 20,000 PSI
Jetstream offers a wide variety of fittings with various connection types to fit your 20,000 psi application needs. The standard connection types, Type M, MP, and MP Tube lance, are available in standard
More informationINSTALLATION AND OPERATION INSTRUCTIONS
INSTALLATION AND OPERATION INSTRUCTIONS Liquid propane units are designed and certified for use, only with household liquid propane supply. Do not use " portable " propane tanks of less than 20-lbs. capacity.
More informationNB/NBR NITROGEN BOOSTER FOR AVIATION SERVICE
NB/NBR NITROGEN BOOSTER FOR AVIATION SERVICE INSTALLATION, OPERATION & MAINTENANCE MANUAL INTERFACE DEVICES, INC. 230 Depot Road, Milford, CT 06460 Ph: (203) 878-4648, Fx: (203) 882-0885, E-mail: info@interfacedevices.com
More information250C-IG COMPRESSOR KIT 12V PART NO C-IG COMPRESSOR KIT 24V PART NO
250C-IG COMPRESSOR KIT 12V PART NO. 25050 250C-IG COMPRESSOR KIT 24V PART NO. 25058 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual
More informationINSTALLATION and OPERATION INSTRUCTIONS
INSTALLATION and OPERATION INSTRUCTIONS FLOJET Beer Pump Panels MODEL NO. 66134-1 66134-2 66134-3 66134-4 IMPORTANT INFORMATION This manual has been prepared to assist you in the operation of Perlick Beer
More information444C DUAL PERFORMANCE VALUE PACK
(Chrome) PART NO. 44432 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using this product. SAVE THIS MANUAL
More informationINSTALLATION INSTRUCTIONS MANUAL ON/OFF SAFETY VALVE/PILOT KIT MODEL GA9050A-1 (F0235)
P/N 126905-01 Rev. B 11/2016 INSTALLATION INSTRUCTIONS MANUAL ON/OFF SAFETY VALVE/PILOT KIT MODEL GA9050A-1 (F0235) For All Single, Dual and Triple Burner Natural and Propane/LP Gas Logs P126905-01 For
More informationCarbon Fiber Tank with EZ Fill system Fill pressure 4,500 psi (310 bar) Output: up to 4,500 psi (310 bar)
Carbon Fiber Tank with EZ Fill system Fill pressure 4,500 psi (310 bar) Output: up to 4,500 psi (310 bar) Ver 1, 10/18 Contents Safety System...3 Filling The Air Venturi Ez Fill System...4 Micro Bore Hose
More informationINSTALLATION, OPERATION AND MAINTENANCE GUIDE
INSTALLATION, OPERATION AND Placement in Pipeline System When installing Process Development & Control s ElastoTITE Elastomer-Hinged Check Valves in a pipeline, a minimum of five pipe diameters should
More information600 o F High Temperature Aging Cell Instruction Manual
600 o F High Temperature Aging Cell Instruction Manual Manual No. D00654827, Revision E Instrument No. 102111608 600 o F High Temperature Aging Cell Instruction Manual 2013 Fann Instrument Company Houston,
More informationuser manual .68 CALIBER ELECTRONIC PAINTBALL MARKER Meets or exceeds ASTM standards.
user manual TM TM TABLE OF CONTENTS: Page Topic(s) 1 Warning and Rules Safe Marker Handling 2 Warranty Information 3 Welcome 4 Initial Assembly 6 Parts Key 7 Exploded Diagram 8 Battery Installation 9 Attaching
More informationIMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS CAUTION - To reduce risk of electrical shock: - Do not disassemble. Do not attempt repairs or modifications. Refer to qualified service agencies for all service and repairs.
More informationCITY AND COUNTY OF DENVER CR&CF RISK UNIT Compressed Gas Safety Standard
CITY AND COUNTY OF DENVER CR&CF RISK UNIT 65.5.11 Compressed Gas Safety Standard 1.0 Introduction 2.0 Scope This standard has been developed to protect all City and County of Denver employees and contractors
More informationH-950 SHRINKFAST HEAT GUN #998
π H-950 SHRINKFAST HEAT GUN #998 1-800-295-5510 uline.com GENERAL SAFETY PROVISIONS Read this manual thoroughly to familiarize yourself with the parts and safe operation of this tool. Keep for future reference.
More information3 GALLON, OILLESS PANCAKE COMPRESSOR INSTRUCTIONS. Item #31289
3 GALLON, OILLESS PANCAKE COMPRESSOR INSTRUCTIONS Item #31289 The EASTWOOD 3 GALLON, OILLESS PANCAKE COMPRESSOR, with an Integral Air Regulator, efficiently supplies all compressed air requirements for
More informationCompact Triple Cabinet Outlet Station Model Installation and Operating Instructions
Compact Triple Cabinet Outlet Station Model 6258-1 Installation and Operating Instructions The Porter Compact Triple Outlet Station (6258-1) provides a quick, safe, and reliable method of connection to
More informationFloat Operated Level Controllers
CONTENTS Float Operated Level Controllers IM0015 Nov. 2014 PAGE Introduction 1 Scope 1 Description 1 Specification 1 Control Installation 2 INTRODUCTION Side Mount Back Mount Prior to installing, the instructions
More informationVOLUMATIC WATER REGULATOR
Introduction The Chore-Time VOLUMATIC regulator is designed to regulate water pressure for Chore-Time Layer and Brood Grow Nipple Watering Systems. There is a model for manual adjustment of the regulator
More informationChipley Custom Machine Deluxe Kit Manual
Chipley Custom Machine Deluxe Kit Manual V 1.0 CCM / DPM 19641 N. Hirsch St Anderson, Ca 96007 Phone- 530-378-3420 Sales- 1-877-412-6850 Fax- 530-378-3420 www.chipleymachine.com I. Table of Contents: I.
More informationInstallation Operating Instructions for Simple Duplex Manual Manifolds PX-TSD Series
Introduction Powerex manifolds are cleaned, tested and prepared for the indicated gas service and are built in accordance with the Compressed Gas Association guidelines. The manifold consists of a regulator
More informationPortable Hydrostatic Pneumatic Test Pump. Procedure Manual
Portable Hydrostatic Pneumatic Test Pump Procedure Manual Dixon Valve & Coupling Company 800 High Street Chestertown, MD 21620 800-355-1991 Fax: 800-283-4966 Specifications Dixon Portable Pneumatic Hydrostatic
More informationOperation Manual. PEGAS NovoTap, PEGAS NovoTap+
Operation Manual PEGAS NovoTap, PEGAS NovoTap+ www.beerinnovations.com Operation Manual 3 1. Assembling Diagram PEGAS NovoTap Assembling Diagram 1. Body 2. Front part of the body 3. Front part of the body
More informationBooster Pump PB4-60 Replacement Kits
Booster Pump PB4-60 Replacement Kits FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product
More informationHydraulic Piston Accumulators
Ride Control Engineering Services PWCE Extendavator Paul Wever Construction Equipment Co., Inc. P.O. Box 85 401 Martin Drive Goodfield, IL 61742-0085 Phone (309) 965-2005 Fax (309) 965-2905 1-800-990-PWCE
More informationTriPod Safety Coupler Installation & Operating Instructions for Models TP4, TP5, TP6, and TP7
TriPod Safety Coupler Installation & Operating Instructions for Models TP4, TP5, TP6, and TP7 March 2014 Form FVC097 - Rev03 IMPORTANT: KEEP THIS DOCUMENT WITH THE PRODUCT UNTIL IT REACHES THE END USER.
More informationG196 Series BASOTROL Redundant Combination Gas Valve with Manual Shutoff Valve
Installation Instructions Issue Date August 19, 2008 G196 Series BASOTROL Redundant Combination Gas Valve with Manual Shutoff Valve Application The G196 valves are suitable for use with natural gas, Liquefied
More informationLP GAS PRODUCTS HIGH QUALITY GAS PRODUCTS SINCE 1957
LP GAS PRODUCTS HIGH QUALITY GAS PRODUCTS SINCE 1957 Enerco, based in Cleveland Ohio, has been at the forefront of infrared technology since 1957. This market leading technology has allowed Enerco to build
More informationCentriFlow Meter Integrated Air Entrainment System
CentriFlow Meter Integrated Air Entrainment System INSTALLATION & OPERATION MANUAL January 2004 Revision 021-4 EASTERN INSTRUMENTS 416 LANDMARK DR. WILMINGTON, NC 28412 910-392-2490 Fax: 910-392-2123 website:
More informationAquor House Hydrant V2
Aquor House Hydrant V2 IN-WALL OUTDOOR FAUCET SYSTEM FLUSH-MOUNT QUICK-CONNECT SELF-DRAINING ANTI-SIPHON NON-FREEZE VBH-SERIES AQUOR HOUSE HYDRANT V2: WALL HYDRANT / FREEZELESS SILLCOCK Freezeless sillcock
More informationNatural Gas Conversion Kit
SERIAL #: Attention: Centro recommends that a qualified gas technician perform the gas supply conversion and orifice replacement for this BBQ model. Natural Gas Conversion Kit F O R U S E W I T H M O D
More information36H SERIES Combination Gas Valve
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL INJURY AND/OR PROPERTY DAMAGE. DESCRIPTION The 36H series combination gas valve is
More informationGEN-1e CO2 Generator OVERVIEW INSTALLATION PROPANE GENERATORS ONLY NATURAL GAS GENERATORS ONLY
GEN-1e CO2 Generator Custom Automated Products offers economical and safe carbon dioxide generators. They produce CO2 by burning either propane or natural gas. We have designed our CO2 generator to allow
More informationRight-Angle Tube Roller Model
SPECIFICATIONS Model no. Free Speed (RPM) Throttle Rotation Max. Torque Ft-Lb Air Pressure psi Air Inlet Hose Air Flow @Free Speed Spindle Weight 909-1700 95 Lever type Reversible 240 90 1/2 NPT 1/2 I.D.
More information400C & 450C DUAL PERFORMANCE VALUE PACKS
(Chrome) PART NO. 40013 (Silver) PART NO. 45012 (Chrome) PART NO. 45013 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before
More informationWARNING: FOR OUTDOOR USE ONLY
Certified to CSA International 4.96 US For Outdoor Gas Fireplaces A HIGHER STANDARD IN QUALITY AND APPEARANCE SAFE AND BEAUTIFUL OUTDOOR LARGO FIRE PIT FOR PROPANE AND *NATURAL GAS OWNER S MANUAL WARNING:
More informationG196 Series BASOTROL Redundant Combination Gas Valve with Manual Shutoff Valve
Installation Instructions Issue Date March 13, 2013 G196 Series BASOTROL Redundant Combination Gas Valve with Manual Shutoff Valve Application The G196 valves are suitable for use with natural gas, Liquefied
More information2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL
2 GALLON TWIN STACK AIR COMPRESSOR W/ HOSE REEL Model: 52024 CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement,
More informationSelf Contained Propane Powered Hammer Owner s Manual. by Tippmann. rev. # 2:
TM Self Contained Propane Powered Hammer Owner s Manual by Tippmann rev. # 2: 6-1-2008 TM CONGRATULATIONS on the purchase of your Tippmann Propane Hammer. We believe the Tippmann Propane Hammer is the
More informationCarbon fiber tank Includes regulator & fill station with hose Fill pressure: 4,500 psi (310 bar) Output: 2,900 psi +/- 10% (200 bar)
Carbon fiber tank Includes regulator & fill station with hose Patent numbers: 6,851,447 7,059,343 7,051,751 Fill pressure: 4,500 psi (310 bar) Output: 2,900 psi +/- 10% (200 bar) Contents Safety system...
More informationUltRo Dual Flow Reverse Osmosis Water System
UltRo Dual Flow Reverse Osmosis Water System Congratulations on this great investment to your health. **IMPORTANT NOTE BEFORE YOU BEGIN** We recommend you call your local friendly plumber to ensure proper
More informationPressure Dump Valve Service Kit for Series 2300 Units
Instruction Sheet Pressure Dump Valve Service Kit for Series 00 Units. Overview The Nordson pressure dump valve is used to relieve hydraulic pressure instantly in Series 00 applicator tanks when the unit
More information310 SERIES TILT-TO-LOAD ROTATOR. The Specialist In Drum Handling Equipment
OPERATOR S MANUAL FOR MORSE TILT-TO-LOAD DRUM ROTATOR SAFETY INFORMATION: While Morse Manufacturing Co. drum handling equipment is engineered for safety and efficiency, a high degree of responsibility
More informationLEAK TROUBLESHOOTING
LEAK TROUBLESHOOTING If you suspect that your TMC isolation system is leaking (most often evidenced by going through air/nitrogen tanks too quickly), this guide will help you to find and fix the problem.
More informationHow Do I Install My Garden Master Bucket Garden?
How Do I Install My Garden Master Bucket Garden? 1. On the arrival of your Bucket Garden open the bucket and remove the 4 screws from the outside of the bucket rim and pull the 2 buckets apart. Check the
More informationOPERATING INSTRUCTIONS AND OWNER S MANUAL READ AND FOLLOW ALL INSTRUCTIONS
READ INSTRUCTIONS CAREFULLY: OPERATING INSTRUCTIONS AND OWNER S MANUAL Model # MH500LPT MH400PT READ AND FOLLOW ALL INSTRUCTIONS Place instructions in a safe place for future reference. Do not allow anyone
More informationPORTABLE 5 GALLON AIR TANK ASSEMBLY & OPERATING INSTRUCTIONS
PORTABLE 5 GALLON AIR TANK MODEL 472 ASSEMBLY & OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com TO PREVENT SERIOUS INJURY, READ AND UNDERSTAND
More informationOPERATION MANUAL obl1 OPERATION MANUAL
www.beerinnovations.com www.beerinnоvations.com obl1 1. Precuations (safety measures) In order to avoid personal injures and damaging the equipment, please carefully review following safety measures before
More informationG92 Series BASOTROL Automatic Pilot Gas Valve
Installation Instructions Issue Date September 17, 2008 G92 Series BASOTROL Automatic Pilot Gas Valve Installation IMPORTANT: Only qualified personnel should install or service BASO Gas Products. These
More informationPaintball Marker. User s Manual. 530 South Springbrook Road Newberg, OR 97132
Paintball Marker User s Manual 530 South Springbrook Road Newberg, OR 97132 Component Concepts, Inc., 530 South Springbrook Road, Newberg, OR 97132 Phone: (503) 554-8095 Fax: (503) 554-9370 www.phantomonline.com
More informationContents. Stainless Steel Side Block. 1.1 Separating the Side Block. Stainless Steel Side Block Reassembly of. Assembly from the Helmet Shell
Separating the Side Block Assembly from the Helmet Shell Contents SSB-1 SSB-3 SSB-5 SSB-5 SSB-7 1.1 Separating the Side Block Assembly from the Helmet Shell 1.2 Side Block Assembly Replacement 1.3 Defogger
More informationRain Barrels. Did You Know?
Rain Barrels Rain barrels are water storage units designed to collect water from impermeable surfaces like roofs. The most common type of rain barrel collects runoff from roofs by connecting to gutter
More informationQuality Plastic Pipe Fittings. Technical Data. Fabricated PVC Fittings IPS Class 100, 125, 160, 200 SCH 40 & SCH 80 Solvent Weld & Gasketed
Quality Plastic Pipe Fittings Technical Data Fabricated PVC Fittings IPS Class 100, 125, 160, 200 SCH 40 & SCH 80 Solvent Weld & Gasketed Effective April 1, 2002 PIPE DIMENSIONS IPS-IRON PIPE SIZE Minimum
More informationUNIVERSITY OF ROCHESTER ENVIRONMENTAL HEALTH & SAFETY
Revision No.: 1 Page 1 of 6 I. PURPOSE This policy/procedure establishes the proper steps for set up, and operation of the BullEx I.T.S Xtreme training system. II. PERSONNEL AFFECTED Fire Safety staff
More informationAuto-Rewind Hose Reels INSTRUCTION MANUAL FOR OXY-LPG MODEL
Auto-Rewind Hose Reels INSTRUCTION MANUAL FOR OXY-LPG MODEL Introduction Thank you for purchasing a Retracta Auto Rewind Hose Reel. The Retracta range of hose reels are a breakthrough in industrial quality
More informationAir Operated Hydraulic Pumping Systems to 50,000 psi
High Pressure Equipment Air Operated Hydraulic Pumping Systems to 50,000 psi PS-10: 10,000 psi PS-20: 20,000 psi PS-30: 30,000 psi PS-40: 40,000 psi PS-50: 50,000 psi PS-90: 90,000 psi High Pressure air
More informationLJ1-25 LouieJRtm Tapping Machine
1/21/08 WARNING: Before using this product, read owners manual and follow all Safety Rules and Operating Instructions. LJ1-25 LouieJRtm Tapping Machine OPERATIONS MANUAL & OPERATING INSTRUCTIONS 30230
More informationContinental Industries STEEL SERVICE TEES or FAX Visit
Continental Industries STEEL SERVICE TEES 1-800-558-1373 or FAX 1-800-788-1668 Visit www.conind.com ABOUT US Our Company Continental Industries, headquartered in Tulsa, Oklahoma, was formed in 1958 and
More informationWelker Sampler. Model GSS-1. Installation, Operation, and Maintenance Manual
Installation, Operation, and Maintenance Manual Welker Sampler Model GSS-1 The information in this manual has been carefully checked for accuracy and is intended to be used as a guide to operations. Correct
More informationThe X-11 Molding Chamber
The User Guide to The X-11 Molding Chamber Table of Contents Overview of Features & Specifications... 3 Features... 4-5 Safety & Maintenance... 6 Initial Startup Procedure... 7 Using the X-11... 8-9 Using
More informationLUBRICATOR ASSEMBLY AND OPERATING INSTRUCTIONS
AIR FILTER, REGULATOR AND LUBRICATOR 4035 ASSEMBLY AND OPERATING INSTRUCTIONS 349 Mission Oaks Blvd., Camarillo, CA 930 Visit our Web site at http://www.harborfreight.com Copyright 004 by Harbor Freight
More informationHYDRAULIC PUNCH DRIVER 38456, 38520, 7306 / 7306SB, 7310 / 7310SB, 7506, 7606SB, 7610SB, 7625 / 7625Pg / 7625PgSB, 7646 / 7646Pg / 7646PgSB
INSTRUCTION MANUAL HYDRAULIC PUNCH DRIVER 38456, 38520, 7306 / 7306SB, 7310 / 7310SB, 7506, 7606SB, 7610SB, 7625 / 7625Pg / 7625PgSB, 7646 / 7646Pg / 7646PgSB Read and understand all of the instructions
More informationULTRA-LIGHT DUTY ONBOARD AIR SYSTEM
ULTRA-LIGHT DUTY ONBOARD AIR SYSTEM PART NO. 10000 IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using
More informationRegulators repair and maintenance. XS Compact 2nd stage. January 2014 Rev XSC /3 Ed. C /14 1
XS Compact 2nd stage January 2014 Rev XSC /3 Ed. C /14 1 XS Compact 2nd stage WARNING! This manual is intended for use by expert technicians who have already received training in equipment repairs and
More informationGas Conversion Kits CERAMIC HEATER SERIES (1, 2, 3, 4 Burner Units)
DESCRIPTION These kits are designed to convert from one gas type to another (eg. from NATURAL to PROPANE or from PROPANE to NATURAL) only for new heaters (5 years or newer) by replacing the gas valve spring
More informationProduct Information News September 26, 2003
Product Information News September 26, 2003 LEVER HEIGHT INSPECTION FOR FIREHAWK MMR MSA is announcing a revision to the instructions for the Firehawk MMR Second Stage Regulator as they relate to the air
More informationHP-104 & HP-106 Tapping Machine OPERATIONS MANUAL
30230 Los Alamos Rd. Murrieta, CA 92563 800-279-5659 FAX 951-926-2334 TappingMachines.com HP-104 & HP-106 Tapping Machine OPERATIONS MANUAL & OPERATING INSTRUCTIONS WARNING READ: Before using this product,
More informationWelcome to your new Firepod It will only work properly on Propane Gas (Also known as LPG and Patio Gas) with the special regulator supplied
Welcome to your new Firepod It will only work properly on Propane Gas (Also known as LPG and Patio Gas) with the special regulator supplied To enjoy your Firepod safely please read the instructions and
More informationSSFU SUPER SPRAYFAST UNIVERSAL ADHESIVE APPLICATOR
S S F U SSFU SUPER SPRAYFAST UNIVERSAL ADHESIVE APPLICATOR MACHINERY DIVISION OWNER S MANUAL UNIT INSTRUCTIONS Please follow all SSFU Safety Instructions. Contact your Duro Dyne Tech Service if you have
More informationSIMPLAIR PIPING TOOL. JXT Company
SIMPLAIR PIPING INGERSOLL-RAND SIMPLAIR PIPING With push-in fittings and lightweight anodized aluminum pipe, a SimplAir system provides ideal connection throughout your entire air distribution system.
More informationCornelius Keg Topping System for Barrels
Product# KEG405 MoreInstructions Cornelius Keg Topping System for Barrels Keg Like A Pro! Congratulations on your purchase and welcome to kegging! This guide is designed to teach you how to clean, sanitize,
More information