2: How to Fill Veloci-T Cartridges
|
|
- Baldwin Lindsey
- 5 years ago
- Views:
Transcription
1 2: How to Fill Veloci-T Cartridges Learn how to fill the cartridges for the Veloci-T Direct-to-Garment Printer guides.equipmentzone.com Page 1 of 11
2 TOOLS: Ink bottle (1) Plastic cup (1) Optional Syringe (1) 2017 guides.equipmentzone.com Page 2 of 11
3 Step 1 2: How to Fill Veloci-T Cartridges Here's how to fill the cartridges for the Veloci-T Direct-to-Garment Printer. Here's what you'll need: Ink bottles. (Cyan, Magenta, Yellow, Black and the bottle of Cleaning Solution.) Syringes. We give you five, one for each color plus one for the cleaning solution. Cartridges. The Veloci-T has five in total. A plastic cup, or a similar container. To be used to fill up the syringe more easily guides.equipmentzone.com Page 3 of 11
4 Step 2 There are five cartridges. One cyan, one magenta, one yellow, and two black cartridges. On the Veloci-T, one of the black cartridges should be filled with cleaning solution. Make sure to put this cartridge in the CL slot when we put the cartridges into the printer later. The two black cartridges are identical other than the fact that one will be filled with black ink and one will be filled with cleaning solution. NOTE: Your cartridges may appear slightly different from the type in the photo guides.equipmentzone.com Page 4 of 11
5 Step 3 One of the black ink cartridges should have a CL label on it. This is the cartridge that should be filled with cleaning solution. If your cartridge is missing that label, stick an extra CL sticker onto it. Step 4 Remove both the clear plug and the colored plug from the top of the cartridge. These pull straight out from the top. Use your hands, not any tools, to remove them. If your cartridge has two colored plugs and no clear plugs, remove both colored plugs instead guides.equipmentzone.com Page 5 of 11
6 Step 5 Once the plugs are removed, it's time to fill your syringe. Pour just a little ink into the cup. You'll need less than an ounce. It's often easier to fill the syringe from a plastic cup than straight from the bottle. Plus, this method helps avoid sucking air into the syringe. Step 6 Remove the syringe from its packaging. Don't worry - the syringe isn't sharp. It's also entirely made of plastic guides.equipmentzone.com Page 6 of 11
7 Step 7 Screw the beige plastic tip onto the syringe. It takes about two turns until it screws on all the way. Step 8 Stick the tip of the syringe into the cup of ink. Pull back on the plunger until you've filled the syringe up to about the 12 cc mark. Keeping the tip of the syringe submerged in the ink as you pull will limit the amount of air which gets into your syringe. That's a good thing guides.equipmentzone.com Page 7 of 11
8 Step 9 Here's what the syringe should look like when it is filled with ink. Again, fill to the 12 cc line. You don't have to be exact. cc is the exact same measurement as ml. So you're filling your syringe with 12 ml of ink. Step 10 Locate the filler hole. This will be towards the back side of the cartridge, the side that has the ink chips. The filler hole will also have a recessed area around it. This area will help to catch excess ink if you accidentally fill your cartridge too much guides.equipmentzone.com Page 8 of 11
9 Step 11 Put the syringe into the filler hole all the way. You'll be creating a seal with the top of the cartridge. It doesn't have to be a tight seal. Push down on the plunger and fill the cartridge with ink. You don't need to fill the cartridge up 100% of the way. 95% full is fine. You will rarely use all the ink in the syringe to fill up the cartridge. That's ok. Just squirt it back into the bottle guides.equipmentzone.com Page 9 of 11
10 Step 12 Put the colored plug back in the filler hole. Leave the clear plastic cap out of the other hole. That hole is the air hole. The air hole should only be covered when you are transporting the printer or leaving the printer unused for a length of time. Step 13 Over a sink, separate the plunger of the syringe from the body. Clean the plunger and the body of the syringe with warm water guides.equipmentzone.com Page 10 of 11
11 Step 14 Push the plunger back into the syringe guides.equipmentzone.com Page 11 of 11
Patients Guide for Self Administering Intravenous Antibiotics General points
Patients Guide for Self Administering Intravenous Antibiotics General points An intravenous line is an open route for infection therefore you need to prevent this by washing your hands before any procedure
More informationUnblocking the MicroSprayer Aerosolizer Model IA-1B With the High Pressure Reverse Cleaning Adapter. Instructions for Use
Penn-Century, Inc. 7670 Queen Street Suite 200 Wyndmoor, PA 19038-8031 USA 215-753-6540 Tel 215-220-3040 Fax www.penncentury.com Unblocking the MicroSprayer Aerosolizer Model IA-1B With the High Pressure
More informationUnblocking the MicroSprayer Aerosolizer Model IA-1C With the High Pressure Reverse Cleaning Adapter. Instructions for Use
Penn-Century, Inc. 7670 Queen Street Suite 200 Wyndmoor, PA 19038-8031 USA 215-753-6540 Tel 215-220-3040 Fax www.penncentury.com Unblocking the MicroSprayer Aerosolizer Model IA-1C With the High Pressure
More informationHow to Make a Boffer Arrow
How to Make a Boffer Arrow By Dean Hitchcox Intro: To make a boffer arrow you should have some experience making other weapons like a sword first. Bows and arrows can be dangerous if not made correctly.
More informationInstalling N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits
Installing N-Strike Recon CS-6 Stage 1 and Stage 2 Performance Kits The Nerf N-Strike Recon CS-6 is a currently available blaster that is relatively easy to modify. The guys at Orange Mod Works have produced
More informationSyringe, Distribution Valve and Infusion Pump Removal/Replacement ATTENTION SYRINGE REPLACEMENT
ATTENTION SYRINGE REPLACEMENT Please read through the document completely before starting any repairs. Refer to the proper section in the service manual for complete removal and replacement procedures.
More informationLe Maitre Ltd. Co2 propelled Electric Air Cannon Instructions. & Loading instructions for Chinese Confetti, Streamers and Glitter
Le Maitre Ltd Co2 propelled Electric Air Cannon Instructions & Loading instructions for Chinese Confetti, Streamers and Glitter Produced by: Le Maitre Ltd, 6 Forval Close, Wandle Way, Mitcham, Surrey CR4
More informationBasic Flows in a Microfluidic Device
Basic Flows in a Microfluidic Device Vishal Tandon 1 Introduction Microfluidic devices are used to transport, mix, and separate analytes in small sample volumes for chemical or biological analysis. Understanding
More informationLAB 06 Organismal Respiration
LAB 06 Organismal Respiration Objectives: To learn how a respirometer can be used to determine a respiration rate. Identify and explain the effect of seed germination on cell respiration. To design and
More informationCyclops + Cyclops + Written By: John Bamford e3d-online.dozuki.com/ Page 1 of 18
Cyclops + Written By: John Bamford 2018 e3d-online.dozuki.com/ Page 1 of 18 TOOLS: Philips Screwdriver (1) Hex Wrench, 1.5mm (1) PARTS: Plastic Screws (2) Collet (2) Collet Clip (2) 30mm Fan (1) Cyclops
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS Ballpark Classics Baseball Game MLB Edition Figure B Read the instructions completely before beginning g assembly. You will need a Phillips screwdriver. 1. Remove the game from the
More informationAQUARIUS. Operating Instructions for the. Type 70 Electrolytic Gas Soldering / Welding Unit. Table of Contents
AQUARIUS Operating Instructions for the Type 70 Electrolytic Gas Soldering / Welding Unit Table of Contents 1. Important General Remarks 2 2. Safety Instructions 2 3. Description of the Soldering Unit
More informationQUIK-jet Micro-Injection System
QUIK-jet Micro-Injection System Training Manual Revision Date: 11/12/07 Table of Contents Subject Headings Pages Introduction 3 Parts of the QUIK-jet Kit 4 QUIK-jet Assembly and Setup 5-6 3 Easy Steps
More informationArticulating Legs with Intraosseous Infusion Simulator LF03840U Instruction Manual
Articulating Legs with Intraosseous Infusion Simulator LF03840U Instruction Manual Products by Nasco C. O. A. D. B. E. M. I. J. G. K. H. F. N. L. About the Simulator Designed to attach easily to any Life/form
More informationWe can tell that diameter of the tube influence the pressure of the water at the bottom.
IDS 102 Pressure Part II You may have found that there is a slight difference in the distance of the two streams, but this is due to frictional forces between the water and the tube, not the different
More informationAtomic Neox Binding Adjustment
Atomic Neox Binding Adjustment I've owned a few pairs of Atomic skis & their Neox bindings, apart from their weight, are great bindings. One of their main benefits being the ability to adjust the fore/aft
More informationThe Making of the Inexpensive Brake Pressure Bleeder
Page 1 of 8 The Making of the Inexpensive Brake Pressure Bleeder Back in early 1999 I mentioned on the Digest(s) that my own personal brake pressure bleeder was made from a pump-up garden sprayer and some
More informationClean toilet plunger Sensor extension cable. Add this important safety precaution to your normal laboratory procedures:
How Does a Trapped Gas Behave? Student Activity Worksheet Driving Question How does a change in volume of a confined gas affect its pressure? Materials and Equipment For each student or group: Data collection
More informationCONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER ABOVE GROUND CURVE STEP / ABOVE GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-AG Note: 40 lbs. of sand required!
More informationTEV-TROPIN [somatropin (rdna origin) for injection] 5 mg & 10 mg
TEV-TROPIN [somatropin (rdna origin) for injection] 5 mg & 10 mg TEV-TROPIN (somatropin for injection) Information for the Patient or Parent Read all instructions before proceeding. Do not mix (reconstitute)
More information1. A proper preparation of the cone and other material is inevitable prior to a CPTU test.
PREPARATION FOR CPTU Procedure for saturation of a piezocone for CPTU 1. A proper preparation of the cone and other material is inevitable prior to a CPTU test. 2. GeoMil Equipment recommends to saturate
More informationUltrasound Guided Thoracentesis Simulator Strap-on Type
Caution Do not mark on the model and other components with pen nor leave printed materials contacted on surface. Ink marks on the models cannot be removed. MW4A Ultrasound Guided Thoracentesis Simulator
More informationUltrasound Guided Thoracentesis Simulator Strap-on Type
Do not mark on the model and other components with pen nor leave printed materials contacted on surface. Ink marks on the models cannot be removed. MW4A Ultrasound Guided Simulator Strap-on Type Instruction
More informationStudents measure the change in pressure by varying the volume of trapped air in a syringe while:
How Does a Trapped Gas Behave? Teacher Information Objective Students investigate the effect of changes in the volume of a confined gas on pressure at constant temperature. Using the pressure sensor, students
More informationCICRA EMERGENCY PROCEDURES
CICRA EMERGENCY PROCEDURES Last updated: Octubre 2011 Please send comments to Carlos Castañeda (ccastaneda@conservacionamazonica.org) Medical evacuation: page 2 Snakebite: page 3 Allergic reaction: page
More informationPARTICLE SPACING PART 1
PARTICLE SPACING PART 1 Name(s) ACTIVITY #1 COMPRESSIBILITY OF LIQUIDS AND GASES Obtain two syringes. Fill one of the syringes about half full of water. Remove any air bubbles left inside. Fill the second
More informationIt was sticking out at the wing end and was too far in at the other.
I've thought for a long time that there was something wrong with my headlight alignment. On dipped beam, it looked all right but on main beam the left and right "hotspots" almost touched each other when
More informationHow to repair a dinged windsurf board
How to repair a dinged windsurf board VERY Important: before the repair, let the board dry out for at least a day in the hot sun. Be sure to read "preparation" below. Repair of a small (1/2") hole in the
More informationNOVALYNX CORPORATION MODEL RAIN GAUGE CALIBRATOR INSTRUCTION MANUAL
NOVALYNX CORPORATION MODEL 260-2595 RAIN GAUGE CALIBRATOR INSTRUCTION MANUAL REVISION DATE: August 2018 Receiving and Unpacking Carefully unpack all components and compare to the packing list. Notify NovaLynx
More informationLab 1. Instrumentation Familiarity: Using Micropipetters and Serological Pipettes
Instrumentation Familiarity: Using Micropipetters and Serological Pipettes Introduction: In molecular biology we sometimes need to measure volumes as small as one millionth of a liter (a liter is about
More informationGas Laws: Boyle s and Amonton s Laws Minneapolis Community and Technical College v.9.08
Gas Laws: Boyle s and Amonton s Laws Minneapolis Community and Technical College v.9.08 I. Introduction The purpose of this experiment is to test the extent real gases (to the limits of our measurements)
More informationRhinoPro Cartridge Gun Manual
RhinoPro Cartridge Gun Manual RhinoPro Cartridge Gun 1500 with 750ml cartridges Table of Contents Application Instructions......................................... 1 Operating Instructions..........................................
More informationINSTRUCTION MANUAL CZ 630/631
INSTRUCTION MANUAL CZ 630/631 Before handling the air rifle read this manual carefully and observe the following safety instructions. Improper and careless handling of the air rifle could result in unintentional
More informationLectric Cycles Mid-Drive Electric Motor Installation
Lectric Cycles Mid-Drive Electric Motor Installation This write-up describes the installation of a Lectric Cycles electric motor. The model is the e-rad Mid-Drive 750 Watt conversion kit, installed on
More informationProduction of alcohol-based handrub
Production of alcohol-based handrub Formulation 1 Diaporama Formulation I For 10 litres Reagents a) Ethanol b) Glycerol c) Hydrogen peroxide d) Distilled water Final concentrations (vol/vol) 80% 1.45 %
More informationExperimental Procedure
1 of 6 10/3/2018, 1:37 PM https://www.sciencebuddies.org/science-fair-projects/project-ideas/microbio_p009/microbiology/yeast-metabolism-aerobic-anaerobic (http://www.sciencebuddies.org /science-fair-projects/project-ideas/microbio_p009/microbiology/yeast-metabolism-aerobic-anaerobic)
More informationREV: 03/17. User Manual
REV: 03/17 User Manual 2 Table of Contents Part 1: Introduction to FSeries Introduction to FSeries Micro-infusion 3 Parts of the FSeries Kit 4 3 Easy Steps for the FSeries 5 Part 2: Setting up the FSeries
More informationRECOMBINATE. [Antihemophilic Factor (Recombinant)] (For intravenous use only)
Website for more information: http://www.recombinate.com/ INSTRUCTIONS FOR USE RECOMBINATE [Antihemophilic Factor (Recombinant)] (For intravenous use only) Do not attempt to do an infusion to yourself
More informationTOURNAMENT ICE. 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual
TOURNAMENT ICE 8Ft-Gold Standard Manual Score Home Air Hockey Game Assembly Instructions / Manual Thank you for purchasing a Gold Standard Games product. All of us at Gold Standard Games want you to be
More informationUltrasound Guided Thoracentesis Simulator
Do not mark on the model and other components with pen nor leave printed materials contacted on surface. Ink marks on the models cannot be removed. MW4 Ultrasound Guided Simulator Instruction Manual Contents
More informationBefore you start sampling, be sure to read
6. DISSOLVED OXYGEN MONITORING: MONITORING: Using the Titration Method Before you start sampling, be sure to read the following pages to familiarize yourself with the equipment and the procedures that
More informationCVC Insertion Simulator
M93UB CVC Insertion Simulator Don t mark on the model and other components with pen or leave printed materials contacted on their surface. Ink marks on the models will be irremovable. Instruction Manual
More informationWritten By: pepe32290
PSP 2000 UMD Drive Replacement Written By: pepe32290 ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION Having trouble reading discs? This guide is for you! TOOLS: Phillips #00 Screwdriver (1)
More informationD. De La Matter 2004 Swimming Pool Chemistry STUDENT ACTIVITIES:
D. De La Matter 2004 Swimming Pool Chemistry STUDENT ACTIVITIES: Good News! Flinn Scientific Inc. has developed a classroom kit of experiments based on these activities. The Kit Catalog # is AP6599. Ordering
More informationPREPARING GAS SAMPLES IN LARGE PLASTIC SYRINGES
PREPARING GAS SAMPLES IN LARGE PLASTIC SYRINGES A wide variety of gases can be prepared safely inside a 60 ml plastic syringe. Here you will practice making carbon dioxide, so that you know the technique
More informationUltrasound Guided Thoracentesis / Pericardiocentesis Simulator Full set
Do not mark on the model and other components with pen nor leave printed materials contacted on surface. Ink marks on the models cannot be removed. MW7 Ultrasound Guided Thoracentesis / Pericardiocentesis
More informationVapor Pressure of Liquids
Vapor Pressure of Liquids In this experiment, you will investigate the relationship between the vapor pressure of a liquid and its temperature. When a liquid is added to the Erlenmeyer flask shown in Figure
More informationGel Loading Practice MiniLab
Gel Loading Practice MiniLab Student s Guide Cat# M3 Version 718 Gel Loading Practice MiniLab (M3) Student s Guide v718 Table of Contents Laboratory Safety Objectives and Background 3 Part I - Using a
More informationTable of Contents Categorized Listing
Notes Guns and Accessories 41 Gun 41 Pistol 41 Rifle - Long Range 41 Rifle - X-Long Range 41 Gun Accessories 41 Arrow Adaptor 41 Blank Adaptor.22 41 Carrying Case - Pistol 41 Carrying Case - Rifle 41 Plunger
More informationThe second stage cannot begin until the first stage is complete.
Addendum to Pneumatic Corker (August 12, 2002) Please read the Operating Instructions before using the pneumatic corker. The purpose of this addendum is three-fold. 1) Describe in more detail how the corker
More informationMassWWP Standard Operating Procedure R-2 Dissolved Oxygen Rev.0 Page 1 of 10
MassWWP Standard Operating Procedure R-2 Dissolved Oxygen Rev.0 Page 1 of 10 MassWWP Standard Operating Procedure R-2 Dissolved Oxygen Rev.0 Page 2 of 10 Table of Contents Field Equipment List...3 Sampling
More informationFish Key Holder. Materials: - 18 gauge sheet steel - 1/4" steel rod ( 1.5 feet is enough ) - Rivets. Material cost: $8 ( with plenty of leftovers )
Fish Key Holder Materials: - 18 gauge sheet steel - 1/4" steel rod ( 1.5 feet is enough ) - Rivets Material cost: $8 ( with plenty of leftovers ) Safety Equipment: - Thick gloves - Goggles - Ear Protection
More informationWELLS JOHNSON HIGH VOLUME CANISTERS
WELLS JOHNSON HIGH VOLUME CANISTERS USER MANUAL DISASSEMBLY OF HARVESTING CANISTERS Please follow the instructions provided to disassemble 5L, 3L, 2L, and 1L, 250mL and 500mL harvesting canisters. 1. Unscrew
More information3190A NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS. Series MODEL NO
NEO-ANGLE DOOR INSTALLATION INSTRUCTIONS Series 30A Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More information6900 Maintenance Instruction System Flush
Equipment Required FA74005 Damper Drain Tube FA16005 Cover Removal Tool FA900005 Beaker 0.25 Litre FA900003 Solvent Cleaning Bottle FA940021 Syringe Polypropylene 50 ml as required FA999045 Gloves Latex
More informationMODEL CCX-AG CURVE STEP / CURVE STEP SYSTEM
To reduce the risk of drowning, entrapment, falls, paralysis, electrocution, or other serious injury or death: Dealer/Installer: Give manual to homeowner. Installer: Read "Safe Installation" on p. 2 and
More informationOXYTEMP Instructions 1
OXYTEMP Instructions 1 Congratulations on purchasing your new OxyTemp Probe! ASSEMBLY INSTRUCTIONS FOR ECO-OXYGEN PROBES 1. Thread the stem into the bottom of the upper housing. 2. Tighten stem with a
More informationActivity Title: Exploring the Ocean with Robots
BEST OF COSEE HANDS-ON ACTIVITIES Activity Title: Exploring the Ocean with Robots Learning Objectives This lesson will introduce students to robotic submarines, called gliders, including basic properties
More informationEnzyme Activity Lab. Wear safety goggles when handling hydrogen peroxide.
Enzyme Activity Lab This laboratory involves the use of an enzyme that will react with hydrogen peroxide. The enzyme is catalase and hydrogen peroxide (H2O2) is the substrate. The reaction is as follows:
More informationMicrofluidic Demonstration
Microfluidic Demonstration Co-flow of liquids across a microfluidic chip Create a microfluidic controller to flow liquids across a microfluidic chip. 1. Assemble fluidic circuits and attach to breadboard.
More informationUltra Concentrate Dispensing System
QC Ultra Concentrate Dispensing System Installation and Operation Manual QC Satellite Mop: QC Central Supply: QC Satellite Spray Bottle: - QC Satellite AG Mop - QC Central Supply AG - QC Satellite AG Spray
More informationmass of container full of air = g mass of container with extra air = g volume of air released = cm 3
1992 Q32 The air pressure inside the passenger cabin of an airliner is 9 x 10 4 Pa when the airliner is at its cruising height. The pressure of the outside atmosphere at this height is 4 x 10 4 Pa. Calculate
More informationPREPARATION AND SELF-ADMINISTRATION INSTRUCTIONS FOR PATIENTS
PREPARATION AND SELF-ADMINISTRATION INSTRUCTIONS FOR PATIENTS Hereditary Angioedema Jenny, a real HAE patient TAKE CONTROL OF YOUR HEREDITARY ANGIOEDEMA (HAE) TREATMENT WITH SELF-ADMINISTRATION Choosing
More informationINSTRUCTION MANUAL. Slavia 630/631
INSTRUCTION MANUAL Slavia 630/631 Before handling the air rifle read this manual carefully and observe the following safety instructions. Improper and careless handling of the air rifle could result in
More informationComplete Rudder installation guide
Complete Rudder installation guide How to install the Rudder kit The Point65 Rudder has been designed to fit all the Point65 models except the DoubleShot. The Nemo DT has no rudder sleeve installed and
More informationMODEL 840 AIR HYDRAULIC PUMP INSTRUCTION
MODEL 840 AIR HYDRAULIC PUMP INSTRUCTION Jackco Transnational Inc. 202 South El Monte, CA 888-452-2526 www.jackco.com FOR YOUR SAFETY Read all instructions, warnings and cautions carefully. Follow all
More informationRetractable Security Cover for a Swim Spa
Parts List Retractable Security Cover Kit 3" PVC pipe Leading edge Cover Track (pre-attached to Swim Spa) Optional cover pump (for outdoor installations) Rocky Roller Kit 2 Roller A-Frame Brackets 1/2"
More informationEvaluation copy. Vapor Pressure of Liquids. computer OBJECTIVES MATERIALS
Vapor Pressure of Liquids Computer 10 In this experiment, you will investigate the relationship between the vapor pressure of a liquid and its temperature. When a liquid is added to the Erlenmeyer flask
More informationRespirator Fit Testing DEPARTMENT OF LABOR Information on the Requirements Types of Respirators & Filters
UNITED STATES Respirator Fit Testing DEPARTMENT OF LABOR Information on the Requirements Types of Respirators & Filters This information is about the respirator fit testing requirements for any worker
More informationSurfboard Repairs Chapter 7
Surfboard Repairs Chapter 7 The Complete Surfing Guide for Coaches - Bruce "Snake" Gabrielson Repair Problems Boards continuously get bumped, hit rocks, break fins, get dropped, and many other things that
More informationCS Controlled Dissolved Gas assembly with optional CS Air Aspirator assembly. Installation and Operation information
CS-425-01 Controlled Dissolved Gas assembly with optional CS-603-01 Air Aspirator assembly Installation and Operation information Serial # CS-XXX Date of shipment:, 2005 Shipped to: Purchase order #: xxxxxxx
More informationPhysics Experiment 17 Ideal Gas Law Qualitative Study
Physics 210 17-1 Experiment 17 Ideal Gas Law Qualitative Study Note 1: Parts of this lab involve using a laptop computer and the PASCO ScienceWorkshop Interface to collect data. The lab also involves use
More informationTEMPERATURE S RELATIONSHIP TO GAS & VAPOR PRESSURE
TEMPERATURE S RELATIONSHIP TO GAS & VAPOR PRESSURE Adapted from "Chemistry with Computers" Vernier Software, Portland OR, 1997 ELECTRONIC LABORATORY NOTEBOOK (ELN) INSTRUCTIONS Read the directions and
More informationProperties of Gases Observing Atom Pressure of a Gas Measuring Gas Products of Chemical Inferring Molecule Reactions
It s a Gas! In a gas, molecules or atoms move constantly and spread far apart. If a gas cannot escape its container, it applies pressure on the container. For example, gas pressure inflates a balloon.
More informationObjective To identify a pure liquid substance using the physical properties of solubility, density, and boiling point.
Chemistry 1020 Identification of an Unknown Liquid Objective To identify a pure liquid substance using the physical properties of solubility, density, and boiling point. Text reference solubility, density,
More informationFitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No
Fitting Instructions for Single Line Mainsail Reefing System For Yachts Up To 9m (30ft) - Part No. 41 130 This single line reefing kit allows reefing control lines to be led aft to the safety of the cockpit.
More information1500 Follow Spot Yoke
1500 Follow Spot Yoke Rev 1.1 2004 City Theatrical, Inc. Getting Started with the City Theatrical Follow Spot Yoke Congratulations on the purchase of your City Theatrical Follow Spot Yoke. The City Theatrical
More informationRARS5000 AIR BODY SAW OWNER S OPERATING MANUAL
RARS5000 AIR BODY SAW OWNER S OPERATING MANUAL DESCRIPTION 1. No mar 2. No mar tip 3. Housing grip 4. Trigger 5. Air inlet 6. Air inlet plug 7. Plastic board Important! It is essential that you read the
More informationCleaning rod: spring steel, stainless steel or carbon fibre cleaning rod - only use a one-piece rod. Avoid using snakes.
Telemark Biathlon Where performance and precision come together http://telemarkbiathlon.com Rifle Cleaning Date : July 19, 2013 Anschutz Rifle Manual - Click Here Izhmash 7-3 Rifle Manual - still looking
More informationCONFER IN-GROUND CURVE STEP / IN-GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL
SAVE THESE INSTRUCTIONS DEALER/INSTALLER: GIVE TO HOMEOWNER CONFER IN-GROUND CURVE STEP / IN-GROUND CURVE STEP SYSTEM ASSEMBLY AND INSTALLATION MANUAL Model CCX-IG Note: 40 lbs. of sand required! SAND
More informationWHITE WOLF. X-ray View MID POWER MODEL ROCKET KIT BUILDING INSTRUCTIONS KIT SPECIFICATIONS:
WHITEWOLF-38 PARTS LIST 1 - Nose Cone 1-17" Airframe 1-6" Motor Tube 3 - Aft Fins 3 - Forward Fins 2 - Centering Rings 1-15" Parachute 2 - launch lugs 1-12 Kevlar Shock Cord 1 - Motor Retention >>(screw/washer)
More information"Aircraft setup is a constant process really. Every
The R/C Aircraft Proving Grounds - Aerobatics Setup Set Up for Success by: Douglas Cronkhite "Aircraft setup is a constant process really. Every time something is changed, there is the chance it will affect
More informationStandard. Abdominal Aortic Aneurysm (AAA) Repair Trainer. Part No: 60610
User Guide Abdominal Aortic Aneurysm (AAA) Repair Trainer Part No: 6060 Standard Part No: 065-088 Issue, June 005 04 Limbs & Things For more Vascular training products visit limbsandthings.com Limbs &
More informationType BBS-03, BBS-05, BBS-06, BBS-25
Type BBS-03, BBS-05, BBS-06, BBS-25 Sterile connection elements Sterile Verbindungselemente Raccords union stériles Operating Instructions Bedienungsanleitung Manuel d utilisation 1. THE OPERATING INSTRUCTIONS
More informationMounting and Operating Instructions EB 8546 EN. Supply Pressure Regulator Type Fig. 1 Supply pressure regulators
Supply Pressure Regulator Type 4708 Type 4708-5352 on Type 3730 Positioner Type 4708-52 with filter receptacle Type 4708-6252 on Type 3372 ctuator Fig. Supply pressure regulators Mounting and Operating
More informationInstruction Manual Updated 5/26/2009 Ver. 2.0
Bench-Mount Filter Press With Air Cylinder Part No. 140-35 Instruction Manual Updated 5/26/2009 Ver. 2.0 OFI Testing Equipment, Inc. 11302 Steeplecrest Dr. Houston, Texas 77065 U.S.A. Tele: 832.320.7300
More informationProp Racer System. User Guide V0210
Prop Racer System User Guide 59718 V0210 Introduction The CO 2 dragster racing activity is popular with older students, but has eluded elementary students due to its complexity. Pitsco s latest race system
More informationParts identification:
ARTERY PUNCTURE AND INTRAMUSCULAR TRAINING ARM Parts identification: FAST-derm replacement skin (removable) Intramuscular injection pad (removable for cleaning) Training arm (includes one FAST-derm replacement
More informationDURRIDGE STAINLESS STEEL SOIL GAS PROBE
DURRIDGE STAINLESS STEEL SOIL GAS PROBE CONTENTS 1. Introduction... 3 2. Placement... 3 3. Connection... 4 4 Measurement... 4 4.1 GRAB Protocol... 5 4.2 Continuous Monitoring... 6 4.3 Thoron Protocol...
More informationAbdominal Aortic Aneurysm (AAA) Repair Trainer User Guide
Abdominal Aortic Aneurysm (AAA) Repair Trainer User Guide Designed and manufactured by Limbs & Things Limited, Sussex Street, St. Philips, Bristol, BS 0RA, UK. Telephone: +44 (0)7 3 0500 Fax: +44 (0)7
More information6800 Maintenance Instruction System Flush Procedure
Equipment Required FA74005 FA65318 FA900005 FA900003 Damper Drain Tube 6800 Cover Removal Tool Beaker 0.25 Litre Solvent Cleaning Bottle FA940021 Syringe Polypropylene 50 ml as required FA999045 Gloves
More informationDissolved Oxygen Study Manual
Dissolved Oxygen Study Manual Table of Contents Introduction 3 Safety Precautions 7 Analytical Techniques 8 Procedure 9 Data Sheet 15 Volunteer Schedule 17 Appendix A: Maps A-1 Appendix B: Fact Sheet
More informationTQC Bresle Chloride test 2008
TQC Bresle Chloride test 2008 SP7310 MANUAL See also : ISO8502-6 ISO8502-9 1 DETERMINATION OF SOLUBLE CONTAMINANTS ON SURFACES IN CONFORMITY WITH ISO 1.1 PREPARATION With this system very low concentrations
More informationMother Natures Mare Foaling Predic- tor Kit (Patent No. 3,519,527)
Mother Natures Mare Foaling Predic- tor Kit (Patent No. 3,519,527) Instruction Manual For Mother Natures Mare Foaling Predictor KitTM (Patent No. 3,519,527) A Product Of: Mother Natures Miniatures, LLC
More informationPAGE (Rev. A - 06/17)
Owners Manual Models 4420BF1UDBFR* and 4420BF1LDBFR* Bi-Level Tubular Bottle Filler Fountain with Pet Fountain and Sanitary Freeze Resistant Triple Valve Control Assembly MODEL (LK)4420BF1UDBFR MODEL (LK)4420BF1LDBFR
More informationVapor Pressure of Liquids
Vapor Pressure of Liquids In this experiment, you will investigate the relationship between the vapor pressure of a liquid and its temperature. When a liquid is added to the Erlenmeyer flask shown in Figure
More informationVapor Pressure of Liquids
Experiment 10 In this experiment, you will investigate the relationship between the vapor pressure of a liquid and its temperature. When a liquid is added to the Erlenmeyer flask shown in Figure 1, it
More informationFitting Instructions For Slab Reefing Kit Part No For Yachts Up To 8.5m (2 Reefing Points)
Fitting Instructions For Slab Reefing Kit Part No 41483 For Yachts Up To 8.5m (2 Reefing Points) This system makes reefing your mainsail a quick and easy operation. Just lower the mainsail just below a
More informationWritten By: Dozuki System
KidWash 2 : PVC Sprinkler Water Toy Written By: Dozuki System 2017 www.botsbits.org Page 1 of 8 INTRODUCTION Fun toy with mister jets helps kids beat the heat. This project owes a big debt to the original
More informationBlue Oyster. Mushroom Grow Bag. Congratulations on your purchase!
Blue Oyster Mushroom Grow Bag Congratulations on your purchase! We hope you will enjoy seeing your mushrooms growing through all the different stages and of course the flavour once picked and cooked. The
More information