Carving Ship Model Hulls Laminated and Machine Carved Hulls
|
|
- Kellie Holly Thomas
- 6 years ago
- Views:
Transcription
1 Carving Ship Model Hulls Laminated and Machine Carved Hulls Pete Jaquith 09 June 2015
2 Topsail Schooner Eagle 1847 Topsail schooner rig Built in Arrowsic Island, ME in /16 to the foot, 1:64 scale Model characteristics Scratch build Laminated solid hull Upper hull planking recessed Built up bulwarks 2
3 Topsail Schooner Eagle 1847 Tools Building board Drawknife Gouges/chisels #49 Pattern Makers File 60 Grit sandpaper w 1.5 dia dowel Sanding sticks Dial calipers Disk sander Drill press 3
4 Topsail Schooner Eagle 1847 Templates (laminated on artist mat board) Stem profile Stern profile Stations Deck camber Deck fore end Bulwark fore end 4
5 Topsail Schooner Eagle 1847 Laminated hull block Bass wood laminations Tilebond glue (brown) Transom a separate assembly Layout profile, deck shear and camber Stem / stern profile Shape stem profile Shape stern profile Shape transom (disc sander) 5
6 Topsail Schooner Eagle 1847 Deck shear / camber Shape fore desk shear and camber (drawknife) Fit transom assembly Shape poop deck shear and camber (drawknife) Layout deck centerline, stations, deck at side, mast holes Drill mast holes (drill press) Shape tumble home aft (disk sander) Shape deck at side fwd (disk sander) 6
7 Topsail Schooner Eagle 1847 Lower hull Shim hull block to hold waterline level Screw hull block to building board Carving lower hull Shape deadrise (drawknife) Rough out stations (gouge) Rough fair between stations (gouge/chisel) Fair between stations (pattern making file/sanding sticks 7
8 Topsail Schooner Eagle 1847 Carving upper hull recess 3/64 recess for upper hull planking Layout inner surface on deck at side 1/16 wide grove at bottom (1/8 below copper line) Vertical cuts with gouges/chisels Finish with sanding sticks 8
9 Topsail Schooner Eagle 1847 Stem, keel, stern post, and rudder Fit stem, keel, and stern post Dry fit rudder Mounting pedestals Drill pedestals holes (drill press) Dry fit pedestals 9
10 Topsail Schooner Eagle 1847 Hull block complete and ready for: Deck planking Poop bulkhead Bulwark framing Upper hull planking 10
11 Topsail Schooner Eagle 1847 Built up bulwarks Timberheads recessed into hull block Every 3 rd timberhead recessed (recommend recessing all at bow) Recesses cut w razor blade and 1/16 chisel Covering board used as template 11
12 Topsail Schooner Eagle 1847 Bulwark and upper hull planking Bulwark planking recessed 1/32 from upper hull Upper hull planking flush with lower hull Upper hull planking extends 1/8 below copper line Lower hull will be coppered 12
13 Topsail Schooner Eagle 1847 Hull, deck, bulwark, deck furniture, hull fittings complete 13
14 Brigantine rig Built in Owls Head, ME in /16 to the foot, 1:64 scale Model characteristics Semi-scratch built from old Model Shipways kit Machine carved solid hull construction Upper hull planking recessed Lower hull coppered 14
15 Templates (laminated on artist mat board) Stem profile Stern profile Stations Deck camber Deck F/A ends Bulwark F/A ends 15
16 Initial assessment Establish key reference lines Buildup required Bottom amidships Stern post and counter Main deck shear and camber Bulwark tops 16
17 Reference lines Center line Keel half siding Stem and stern profile Stations Deck at side Bulwark top (inner and outer lines) 17
18 Lower hull Shim hull block to hold waterline level Screw hull block to building board Carving lower hull Shape stem & stern profile Shape deadrise (sanding block) Rough out stations (gouge) Rough fair between stations (gouge/chisel) Fair between stations (pattern making file/sanding sticks) 18
19 Carving upper hull recess 3/64 recess for upper hull planking Layout inner surface on bulwark top 1/16 wide grove at bottom (1/8 below copper line) Vertical cuts with gouges/chisels Finish with sanding sticks 19
20 Stem, keel, stern post, and rudder Fit stem, keel, and stern post Dry fit rudder Mounting pedestals Drill pedestals holes (drill press) Dry fit pedestals 20
21 Hull block complete and ready for: Upper hull planking Carving inner bulwarks Deck framing Deck planking Bulwark framing 21
22 Bulwark and upper hull planking Bulwark planking recessed 1/32 from upper hull Upper hull planking flush with lower hull Upper hull planking extends 1/8 below copper line Lower hull will be coppered 22
23 Inner bulwarks 1 st exterior planking installed with Tilebond wood glue Carving inner bulwarks Layout inner cut line on bulwark top Vertical cuts with gouges/chisels Finish with sanding sticks Control thickness to with dial calipers ~1/16 total thickness (1/32 + 1/32 planking) 23
24 Inner bulwarks Finish with sanding sticks Control thickness to with dial calipers ~1/16 total thickness (1/32 + 1/32 planking) 24
25 Deck framing Deck framing built up from basswood strip Used to establish correct deck shear and camber 25
26 Mast holes Drill mast holes (with drill press) 26
27 Deck planking and bulwark framing Typical deck planking, waterways, covering board, and bulwark framing Bulwark framing fwd based on figures in The American-Built Clipper Ship by William L. Crothers 27
28 Hull, deck, bulwark, deck furniture, hull fittings complete 28
Making Spars for the Schooner Jeanette
Making Spars for the Schooner Jeanette..... by Byron Rosenbaum Figure 1. Byron Rosenbaum s 1:16-scale radio-controlled model of the schooner Jeanette. All photographs by the builder. The spars required
More informationGREEK TRIREME, 480 B.C. Scale: 1/72 Length: 515mm Width: 180mm Height: 220mm
GREEK TRIREME, 480 B.C. Scale: 1/72 Length: 515mm Width: 180mm Height: 220mm HISTORY: The model represents a Greek Trireme from the age of battle of Salamis (480 B.C.). The crew were 170 oarsmen and about
More informationBuilding the Model Shipways kit of the colonial schooner Sultana
Building the Model Shipways kit of the colonial schooner Sultana Introduction by Chuck Passaro These shop notes have been prepared for those of you who enjoy the hobby and wish to take their modeling projects
More informationVikings ship GOKSTAD, 9 th century Scale: 1/72 Length: 305mm Width: 135mm Height: 182mm
Vikings ship GOKSTAD, 9 th century Scale: 1/72 Length: 305mm Width: 135mm Height: 182mm HISTORY: This model represents a Viking ship found in year 1880 near village Gokstad in Norway. The ship was built
More informationHansa COG 14 th century SCALE: 1/72 Length: 430mm Width: 210mm Height: 330mm
Hansa COG 14 th century SCALE: 1/72 Length: 430mm Width: 210mm Height: 330mm HISTORY: The Hansa was a medieval association of German cities which engaged by in long distance business mainly in area of
More informationMARIA HF31. SCALE: 1/72 Length: 365 mm width: 85mm height: 295 mm
MARIA HF31 SCALE: 1/72 Length: 365 mm width: 85mm height: 295 mm HISTORY: Maria HF 31 is a fishing Ewer whose home base was Finkenwerder in northern Germany. Maria HF31 operated in the North Sea for more
More informationCATBOX. A Puddle Duck Racer. By Jim Michalak
CATBOX A Puddle Duck Racer By Jim Michalak CAT BOX HULL SPECIFICATIONS 1. Bow transom from 1/4" plywood. Top and bottom edges framed with 3/4 x 1-1/2" lumber with bevels as shown. Mark centerlines boldly.
More information1/10 th Scale 1956 Ted Jones Classic Hydroplane
1/10 th Scale 1956 Ted Jones Classic Hydroplane Preparation These plans show outside sheeting of 3/32 balsa laminated with 1/64 birch ply. This makes a light and strong skin for this boat. Optionally you
More informationKNARR. SCALE: 1/35 length: 440mm width: 300mm height: 400mm
KNARR SCALE: 1/35 length: 440mm width: 300mm height: 400mm HISTORY: The Knarr is a type of Viking ship which serves for long trade naval business. The Knarrs were very robust and very well resist against
More informationLITTLE TRI construction
LITTLE TRI construction I have built almost anything that can sail. At the age of 12 my first sail thing, an ice boat. I used skates which had to be mounted on shoes as runners. Big fun, very fast, only
More informationPlace a rope coil here
1 2 3 4 The anchor buoys were made from Sculpey. You could however, carve them from wood but I wanted to continue my experimentation with this material. A buoy from this time period would have ranged from
More informationPaper Tiger Catamaran International Association MEASUREMENT FORM
Paper Tiger Catamaran International Association MEASUREMENT FORM Amended June 2000: July 2002: April 2012 Name of boat: Sail No: Owner s name: Owner s address: Postcode: Phone: (H) (B) (Mob.) Email: Owner
More informationParts of the Ship. Terms you should already know
Parts of the Ship Toronto Brigantine Terms you should already know After-peak Fore-peak Bow Stern Fairlead Scupper Freeing port Hull Deck Lifeline Hatch Skylight Cleat Pin-rail Fife-rail Spider-band Block
More informationTugster. Tug Boat. Competition or Sport Tug Kit. A Zippkits R/C Boat. Building Instructions
Z I P P M A N U FA C T U R I N G Tugster Tug Boat Competition or Sport Tug Kit A Zippkits R/C Boat Building Instructions 2016 JMP Hobby Group St. Paul, Indiana 47272 www.zippkits.com Toll Free (866) 922-ZIPP
More informationApsara Hard chine version
Apsara Hard chine version Update of the RG65WIKI page. Introduction One often encounter people on forums looking for simple to build hard chine hulls. The RG65 class is ideal for initiation to remote controlled
More informationD. N. HYLAN & ASSOCIATES, INC. BOATBUILDERS COQUINA STUDY PLANS
D. N. HYLAN & ASSOCIATES, INC. BOATBUILDERS COQUINA STUDY PLANS LOA - 6' " BEAM - 6" DRAFT, " board up, 36" board down WEIGHT - with rig, 50 lb HULL TYPE - round bottom lapstrake CONSTRUCTION - glued lapstrake
More informationVALDIVIA BUILD LOG Dr Ron
VALDIVIA BUILD LOG Dr Ron The Robbe kit of the two-masted schooner Valdivia was purchased in 2007, along with the fitting set and propulsion accessories, and has been staring me in the face since then
More informationH.M. SCHOONER PICKLE THE TRAFALGAR DISPATCH
H.M. SCHOONER PICKLE THE TRAFALGAR DISPATCH Manual 1 of 2 Hull Construction, Masting & Rigging Additional photos of every stage of construction can be found on our website at: http://www.jotika-ltd.com
More informationAn Australian Classic by spectre.com
An Australian Classic by www.go spectre.com Your Bug! Welcome to the Balain Bug experience!!!!!! The Bug kit has been designed so as to be a modern version of the Traditional Bug now you can sail like
More informationLE CERF, Scale: 1/72 Length: 685mm Width: 255mm Height: 520mm
LE CERF, 1779-1780 Scale: 1/72 Length: 685mm Width: 255mm Height: 520mm HISTORY: The cutter LE CERF was build after the plans of well known French ship designer Denys. The CERF was launched in March 2,
More informationBlazer Marine, Whiplash Sport 40
Blazer Marine, Whiplash Sport 40 Thank you for choosing to build the Whiplash 40. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We are excited
More informationL CLASS MULLET BOAT RESTRICTIONS
L CLASS MULLET BOAT RESTRICTIONS 1 It is the intention of these restrictions to produce an able type of vessel, and to perpetuate the modern type of mullet boat. The Ponsonby Cruising Club Inc. as ruling
More informationConstitution Instructions
Constitution Instructions This kit will build a 1:48 scale hull for the USS Constitution frigate. The kit contains the following parts. 1/8 deck with laser etched deck lines 1/8 railing Ribs Center keel
More informationAUSTRALIAN ARROW AND ARAFURA CADET ASSOCIATION ARROW CATAMARAN RESTRICTIONS AND MEASUREMENT CERTIFICATE
AUSTRALIAN ARROW AND ARAFURA CADET ASSOCIATION ARROW CATAMARAN RESTRICTIONS AND MEASUREMENT CERTIFICATE 1 NOTE: The object of these restrictions is to provide uniform specifications and restrictions for
More informationSUNBURST CLASS RESTRICTIONS & MEASURER'S SHEET FOR REGISTRATION (Supplementary to the plans)
Box 33 608, AUCKLAND SUNBURST CLASS RESTRICTIONS & MEASURER'S SHEET FOR REGISTRATION (Supplementary to the plans) NOTICE TO MEASURER 1. Tick as appropriate. Record all measurements. as at November 2015
More information8-GUN CORVETTE ASSEMBLY INSTRUCTIONS
8-GUN CORVETTE ASSEMBLY INSTRUCTIONS THE HULL STEP 1 Fasten the Deck to the Hull. Find the hull. This is a large, pink, ship-shaped piece of insulating foam board. This will form the base of your model
More informationCub Scout Pack Rain Gutter Regatta
Cub Scout Pack 350 2014 Rain Gutter Regatta Event Location & Date: Advance Firehouse, Saturday November 22nd 11:00am-1:00pm (racing as soon as everyone registers) 106 E Wall Street Advance, IN 46102-9407
More informationConstructing the Masts
A: Fore Mast completed B: Main Mast unpainted C: Boom Rest D: Unpainted mast detail (fore and main mast) A D B C Constructing the Masts The main and fore masts are virtually identical. At least as far
More informationBuilding a model of a Thames Barge
Building a model of a Thames Barge Stage 1 : Reading the instructions The model which I purchased is of the Will Everard, a steel-hulled barge built in the 1920's, one of a range of laser-cut kits from
More informationRattlesnake INSTRUCTION MANUAL MASSACHUSETTS PRIVATEER
INSTRUCTION MANUAL Rattlesnake MASSACHUSETTS PRIVATEER Technical Characteristics Scale: 3/16 = 1 0 (1: 64) Overall Length: 28 Overall Width: 9 Overall Height: 18 Hull Width: 4-1/4" MODEL SHIPWAYS KIT NO.
More informationConstruction Chapters Index
Construction Chapters Index 9 7 8 Chapters Index c. c. c. c. c. c. c7. c8. c9. c0. c. c. c. c. c. c. c7. Balsa Wood Skeleton Strip Planking Hull Fairing Keel Bulb Mould Lead Bulb Casting Keel Construction
More informationPAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro
1980 82 PAY N PAK, 1/12 th Scale, Limited Sport Hydro P Sport Hydro Introduction: The 1980 turbine Pay N Pak is a good subject for a model race boat. It has a low profile, mild pickle-fork setback, long
More informationSTRUCTURAL MEMBERS OF A SHIP. compartment stem frame beam bracket girder stern post hull angle bar stiffener
Unit 2 SHIPS AND SHIPS TERMS STRUCTURAL MEMBERS OF A SHIP Basic terms shell plating strake keel deck tank top floor stringer buoyancy strength stability bulkhead compartment stem frame beam bracket girder
More informationBuilding the Corel Endeavour
SPECIAL ISSUE # 7 DECEMBER 2017 All photographs and articles published remain the copyright property of the contributor and SMSC unless released. Building the Corel Endeavour Photos and commentary by Leon
More informationBoat Strength Errata & Updates 5/7/18 Sheet 1 of 5
Boat Strength Errata & Updates 5/7/18 Sheet 1 of 5 Formulas 1-2 and 1-3, page 7: Instead of averaging LOA and LWL and when LOA is more than 108% and instead of averaging BOA and BWL when BOA is over 112%,
More informationSHIP FORM DEFINITION The Shape of a Ship
SHIP FORM DEFINITION The Shape of a Ship The Traditional Way to Represent the Hull Form A ship's hull is a very complicated three dimensional shape. With few exceptions an equation cannot be written that
More informationINSTALLING YOUR CLC RUDDER
INSTALLING YOUR CLC RUDDER These instructions are written to help you install the CLC rudder kit on your wooden kayak. The rudder can be fitted to your boat during construction or after completion. Please
More informationBuilding your first hull.
Building your first hull. You ve built your first model boat from a kit, and now you re ready to scratch-build a scale model. You may find what you need as a ready-made hull. Alternatively you may decide
More informationLOD 39.8, LWL 29.1, Beam 11, Draft 4.7 (centerboard up), Displacement 21,000 lbs Designer: Wirth M. Munroe Built 1956 by Warren Bailey.
COMANCHE LOD 39.8, LWL 29.1, Beam 11, Draft 4.7 (centerboard up), Displacement 21,000 lbs Designer: Wirth M. Munroe Built 1956 by Warren Bailey. Comanche was designed and built in Miami for Jack Price,
More informationZEPHYR CLASS RULES. June 2014
1. GENERAL 1.1. Name ZEPHYR CLASS RULES June 2014 The class shall be known as the Zephyr Class. The Zephyr is a one-design class. 1.2. Control The class shall be administered by the Zephyr Owners Association
More informationStevenson Projects Building the Hull Top Deck and Bulkheads
Stevenson Projects Building the Hull 1. Print out both piece sheets. 2. Cut out one keel piece and glue it to a piece of balsa wood or dense cardboard. Cut out the second keel piece and glue it to the
More informationWILLEY CAT SHEET B. Daggerboard - 9mm x 2 Daggerboard Ballast - Lead/Epoxy - 6" diameter
WILLEY CAT Willey Cat was designed for performance. The flexible reefing arrangement allows tailoring your sail area to wind conditions. Best with a crew of -. DESIGN FEATURES Flexible Reefing - reefs
More information1 Aims and Objectives of these rules
Building and Measurement Rules for the St Ayles Skiff 2014 Edition 1 Aims and Objectives of these rules 1.1 The boats to be raced shall be available to as many people as possible. 1.2 The quality of the
More informationTHE BROADAXE. NEWSLETTER of THE SHIP MODEL SOCIETY OF NEW JERSEY Founded in Volume 27, Number 9 September, 2009
THE BROADAXE NEWSLETTER of THE SHIP MODEL SOCIETY OF NEW JERSEY Founded in 1981 Volume 27, Number 9 September, 2009 MINUTES OF THE REGULAR MEETING August 25, 2009 The meeting was called to order by President
More informationTable 4. Key to parts shown on the plans of the pinas (see plan drawings 1 5 following table).
Table 4. Key to parts shown on the plans of the pinas (see plan drawings 1 5 following table). Ship compartments: A hold B forepeak C protective bulwark for the pumps D powder room E cheese and bread room
More informationMasthead Sensor Installation Guide
2315 1/2 Artesia Blvd. Redondo Beach, CA 90278 (310) 320-4349 (310) 320-5026 Fax www.signetmarine.com service@signetmarine.com Masthead Sensor Installation Guide 2.3 Masthead Sensor Installation Continued
More informationCarving a Custom Seat
Carving a Custom Seat Seat Carving your own seat from mini-cell, high-density foam is really quite simple and has proven to be more comfortable than any commercially produced seat and often more reasonably
More informationODOM CLASS SPECIFICATIONS
ODOM CLASS SPECIFICATIONS Effective March 1, 2004 1. GENERAL 1.1 Purpose of the Measurement Rules 1.1.1 The ODOM is a One-Design Class as defined by the American Model Yachting Association (AMYA). However,
More informationBonHomme Richard. as a Ship-in-Light-Bulb Model. ... by John Fox III
BonHomme Richard as a Ship-in-Light-Bulb Model..... by John Fox III Figure 1. I am on a mission to prove that shipin-bottle (or light bulb) models can be every bit as historically accurate, and to scale,
More informationCONSTRUCTION OF A GUNBOAT A CLASS YACHT by Brian Dill
CONSTRUCTION OF A GUNBOAT A CLASS YACHT by Brian Dill The Gunboat design is the latest Radio A class from Graham Bantock, optimised to provide the best boat speed below 4 knots and to be as good as possible
More informationRULES PUBLICATION NO. 20/P SHIP SIDE STRENGTHENING OF FISHING VESSELS MOORING AT SEA ALONGSIDE OTHER VESSELS
RULES PUBLICATION NO. 20/P SHIP SIDE STRENGTHENING OF FISHING VESSELS MOORING AT SEA ALONGSIDE OTHER VESSELS 1995 Publications P (Additional Rule Requirements), issued by Polski Rejestr Statków, complete
More informationO K D I A MEASUREMENT FORM INTERNATIONAL OK DINGHY CLASS
O K D I A 2010 MEASUREMENT FORM INTERNATIONAL OK DINGHY CLASS NOTES GENERAL 1. The builder shall pay the current building fee to the National OK Dinghy Association which shall issue a building fee receipt
More informationINTERNATIONAL FLYING FIFTEEN CLASS MEASUREMENT FORM
INTERNATIONAL FLYING FIFTEEN CLASS MEASUREMENT FORM 2014 Authority: * International Sailing Federation, Ariadne House, Town Quay, Southampton, Hampshire, SO14 2AQ, UK IN ORDER TO OBTAIN A MEASUREMENT CERTIFICATE
More informationPhoto Essay: How to Build a Nova Scotian Grand Banks Dory By Jeff Spira Plans available at: http://spirainternational.com/ How to Build a Nova Scotian Grand Banks Dory By Jeff Spira In Lunenburg, Nova
More informationINSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.)
INSTRUCTIONS FOR GLUING ON THE BUMPER FOR PORT TOWNSEND WATERCRAFT S NESTING DINGIES. (Or requires a 1 surface to adhere to.) The PT 11 bumper is made from a high quality, non marking EPDM rubber. This
More informationSailing Seats. Traditional Rowing Seats
The SILING PEPOD L 6 William C ates L 1 Sailing Seats Traditional Rowing Seats SILING PEPOD design by William C ates Specifications & Salient Features Length Overall: 16 ft 6 - ½ in Maximum eam: 5 ft 1
More informationOK DINGHY INTERNATIONAL ASSOCIATION. MANUAL OF MEASUREMENT Revised Apr 2009
OK DINGHY INTERNATIONAL ASSOCIATION MANUAL OF MEASUREMENT Revised Apr 2009 1. GENERAL This manual should be read in conjunction with the racing rules of sailing 2009-2012, the current class rules and measurement
More informationThe Baltimore Clipper
The Baltimore Clipper PRIDE OF BALTIMORE II Early History A type of sailing vessel known as the Baltimore Clipper first appeared during the American Revolution. Because the ship was so fast, it s hull
More informationDRAGONFLITE 95 RESTRICTED CLASS RULES 2016
DragonFlite Force 95, Restricted Class Rules 2016 2013 Version 1.0 DRAGONFLITE 95 RESTRICTED CLASS RULES 2016 Version 1.0 DF Racing Rules Committee 2016 Introduction The DragonFlite 95 (DF95) project started
More informationCAMPER & NICHOLSON XYRIS CLASS 30 FT SLOOP SOLD
HERITAGE, VINTAGE AND CLASSIC YACHTS +44 (0)1202 330 077 CAMPER & NICHOLSON XYRIS CLASS 30 FT SLOOP 1939 - SOLD TWINK CAMPER & NICHOLSON XYRIS CLASS 30 FT SLOOP 1939 Designer John Nicholson Length waterline
More informationArmed Virginia Sloop - Part 4 Deck Fittings
Armed Virginia Sloop - Part 4 Deck Fittings With the deck planking completed, I planked the quarterdeck bulkhead and painted the inside of the bulwarks (but not the outside of the hull). Then I moved on
More informationDRAGONFLITE 95 RESTRICTED CLASS RULES 2016
DragonFlite Force 95, Restricted Class Rules 2016 2013 Version 1.2 1.0 DRAGONFLITE 95 RESTRICTED CLASS RULES 2016 Version 1.2 DF Racing Rules Committee 2016 Introduction The DragonFlite 95 (DF95) project
More informationHat s off to you for choosing a kit from Port Townsend Watercraft.
Hat s off to you for choosing a kit from Port Townsend Watercraft. 1 A 30 year fascination with the challenges of nesting boat design, and many prototypes have led to the PT Eleven. Because you chose this
More informationWebsite:
Introduction The Javelin is a high performance, single trapeze, 14ft two-handed skiff raced competitively throughout New Zealand and Australia. Its lightweight 70kg hull, and powerful, efficient sail plan
More informationRiviera Draft Shaft Hole Boring
Riviera Draft Shaft Hole Boring a. Height from bottom of hull thru the hull to the center of the drive shaft. This will be calculated. b. Height of drop of strut. The strut for the Riviera is 7.5 c. Distance
More informationWHITE ENSIGN MODELS. 7. Etched parts 20 are the netted sections of railing that fit to the edges of the mid gun deck extensions, kit parts D25.
WHITE ENSIGN MODELS RN Littorio-Class Battleships Photoetched Metal details to fit the Trumpeter kits in 1/00 Scale Instructions for working with Photoetched Metal 1. Do not remove the etched parts from
More information10-gun Sloop Mediator TITLE Original Plan Tracing & General Views
0 BREADROOM 0 MAGAZINE FIRE PLAE KETTLE 0 0 ORIGINAL PLAN TRAING SALE IN FEET 0 S. Plan showing the body plan with stern board outline, profile with some inboard detail, and longitudinal half-breadth with
More informationChapter Twelve. Starting the rigging process
Chapter Twelve Starting the rigging process Before I begin describing the rigging process, I must remind folks that it would be a great time to slip that traveler ring onto the bowsprit. I forgot to mention
More information1/600 Scale HMS Leander
1/600 Scale HMS Leander Royal Navy Frigate Photo-etched detail set to fit the Airfix kit Parts List 1 2 3 4 5 6 7 8 9 10 11 31 32 30 12 13 14 15 16 19 20 21 22 17 18 23 24 26 27 29 37 25 33 34 35 39 36
More informationTHE AMERICAN FISHING SCHOONER
THE AMERICAN FISHING SCHOONER Technical Characteristics Scale: 1/4 = 1 ft. ( 1: 48 ) Length: 33 Width: 5-1/2 Height: 28 Manufactured by Model Shipways Kit No. MS2109 BENJAMIN W. LATHAM The northward spring
More informationSoling Building Tips II
Soling Building Tips II Prepared: Arthur Deane Jan 20, 2002 adeane@ic.net Introduction The following are some lessons learned and experience gained in building a Soling kit. The plan developed is based
More informationOPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE
Page 1 of 8 Compiled by Chief Examiner Approved by Qualifications Committee: 27 September 2013 OPERATIONS SEAFARER CERTIFICATION GUIDANCE NOTE SA MARITIME QUALIFICATIONS CODE Page 2 of 8 KNOWLEDGE, UNDERSTANDING
More informationNORDIC FOLKBOAT. INTERNATIONAL CLASS RULES Edition 2017 (Latest changes/amendments in RED)
NORDIC FOLKBOAT INTERNATIONAL CLASS RULES 2017 2020 Edition 2017 (Latest changes/amendments in RED) Effective: January 1 st, 2017 Page 2 of 36 Table of Contents 1. GENERAL... 4 1.10 Purpose of the Class
More informationNot to Scale 650mm 152mm 100mm gap RacingSparrow RG65 v1.0 Based on the 75cm boat in the book Build Your Own Radio Controlled Yacht this RG65 design a
Designer:Bryn Heveldt. VERSION v1.0 Not to Scale 1100mm would be this high as per the maximum height in the class rules. RacingSparrow RG65 www.racingsparrow.co.nz VERSION v1.0 The rig stands at 942mm
More informationTHE CLASS RULES OF THE INTERNATIONAL 12 SQUARE METRE ONE DESIGN SHARPIE
THE CLASS RULES OF THE INTERNATIONAL 12 SQUARE METRE ONE DESIGN SHARPIE THE CLASS RULES OF THE INTERNATIONAL 12 SQUARE METRE ONE DESIGN SHARPIE The official language of the Sharpie Class is English. In
More informationaero naut Order No. 3009/00
aero naut Order No. 3009/00 Introduction: The model should be assembled following the sequence of the stages of construction described in these instructions. The laser-cut components are individually numbered.
More informationAGM 33 PIKE ALL FIBERGLASS. Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List
ALL FIBERGLASS AGM 33 PIKE Specifications Length: 92 Diameter 5.5 Weight: 24 lbs Motor Mount: 75mm Fins: 6-3/16 G10 CP: 68 from nose tip Parts List (1) Filament Wound Nose Cone w/ Metal Tip (1) Nose Cone
More informationGeneral Precautions RESIN & WHITE METAL PARTS
Type Anti Aircraft Frigate H.M.S. PUMA 70 /30 Scale The Type or Cat class were a class of anti aircraft frigates built for the Royal Navy as escort vessels to provide anti aircraft cover for convoys. After
More informationSurfboard Repairs Chapter 7
Surfboard Repairs Chapter 7 The Complete Surfing Guide for Coaches - Bruce "Snake" Gabrielson Repair Problems Boards continuously get bumped, hit rocks, break fins, get dropped, and many other things that
More informationMike Hungerford's notes on building Ron Caudillo's TOS Enterprise
Ron Caudillo, designer of this model, has kindly given his approval for release of my redraw/repaint/rework of it. The colors chosen for the model are subdued approximations of the colors found on the
More informationStar 45 Short Kit Build by Bob Szczepanski
Star 45 Short Kit Build by Bob Szczepanski An old used Star 45 showed up at our pond one day last Fall. Nostalgia struck and I was hooked! A flood of memories sailing an International Star boat on Lake
More informationINTERNATIONAL 420 CLASS MEASUREMENT FORM & MEASUREMENT CERTIFICATE
INTERNATIONAL 420 CLASS MEASUREMENT FORM & MEASUREMENT CERTIFICATE BOAT DETAILS NATIONAL LETTERS OFFICIAL SAIL NUMBER FIRST OWNER OF HULL RE-REGISTRATION (if change of Nationality) Authority: International
More informationScuba Doo II Technical Report International Submarine Race #11 May 2, 2011
Scuba Doo II Technical Report International Submarine Race #11 May 2, 2011 Team Members: Joe Allen Michael Cargill Sean Connor Matt Crist Sean LaMontagne Matthew Notaro Langdon Tarbell Zach Venne Introduction
More informationDornier Do R 4 Super-Wal
Dornier Do R 4 Super-Wal Model Aviation Laddie Mikulasko s Dornier Do R 4 Super-Wal Build the multiengine, record-setting seaplane. Article, plans, instructions, and photos by Laddie Mikulasko. Complete
More informationPART II Building the MDV-1
21 PART II Building the MDV-1 The MDV-1 is a simple, easily driven, seaworthy boat intended for both rowing and power propulsion. Its general-purpose design is suitable for inshore waters around the world.
More informationGRP BOAT BUILDING INSTRUCTIONS 2006
125 ASSOCIATION VICTORIAN DIVISION INC. GRP BOAT BUILDING INSTRUCTIONS 2006 TABLE OF CONTENTS 1.0 COPYRIGHT 4 2.0 PLAN SET and MEASUREMENT 4 3.0 MATERIALS FOR HULL 4 3.1 Patterns 4 3.2 Foam Panels 4 3.3
More informationBlazer Marine, Whiplash Sport Hydro
Blazer Marine, Whiplash Sport Hydro Thank you for choosing to build the Whiplash Sport Hydro. We have spent over 12 years perfecting this design, and finally we are making it available to the world. We
More information6th MELBOURNE CUB SCOUT PACK
6 th Melbourne Scout Group 55 McCracken Street Kensington 3031 Group Leader Grant Randle 6th MELBOURNE CUB SCOUT PACK Official (with thanks to Cub Scout Pack 70, New Canaan, Connecticut and Pack 957 in
More informationUncle John's Choupique Road Sulphur, LA Materials needed to build the basic boat 1/4" x 48" x 96" exterior plywood ~ 3 sheets
Uncle John's 5229 Choupique Road Sulphur, LA 70665 Thank you for purchasing our plans. Have a safe and enjoyable experience building and using your craft. Materials needed to build the basic boat 1/4"
More information400/488 Rotating Davit Installation Instructions
400/488 Rotating Davit Installation Instructions These instructions were written with the owner in mind. If you are the installer make sure these instructions are passed along to the owner of the boat.
More informationStep 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the seam joint is.
WhiplashGV Instruction Manual Email: Brian@Blazermarine.com Phone: 513-598-1769 Step 1: Block sand the transom to remove the seam joint. The end result should be a flat transom without a ledge where the
More informationSEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT
SEADUCER BOATS GAS MONO COME VISIT US ON THE WEB AT WWW.SEADUCERBOATS.COM 1 - Pkg. Of 440 push rod ends 1 - Pkg. of solder-on rod ends 2 -water outlet fitting 1-1/4" prop nut 1 -.250" x 24" flex shaft
More informationINSTALLING THE PROWLER 13 RUDDER
INSTALLING THE PROWLER 13 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 Rubber 2 Rail Assemblies Rudder Body 1 Rudder Retraction Grommets (includes steering
More informationINDEX CLASS RULES. ISSUED 3 - June 2007 ONE POINT FIVE CLASS RULES
CLASS RULES INDEX 1. INTRODUCTION 2: 1.5 CLASS SPECIFICATIONS 3: CLASS PHILOSOPH 4: HULL AND DECK 5: KEEL / BULB AND RUDDE 6: DECK FITTINGS 7: SPARS AND RIGGING 8: SAILS ISSUED 3 - June 2007 ONE POINT
More informationPARTS OF A SHIP. Fore and Aft Rigged Schooner. Square-Rigged Brig. Side-Wheel Steamer. Steam Propeller. Bulk Freighter. Great Lakes Schooner
PARTS OF A SHIP Pilothouse Porthole Life Boat Steam Propeller STERN Ship s Wheel Cornelia B. Windiate Great Lakes Schooner Site Plan Yawl Boat Mizzen Mast Smoke Stack Bulk Freighter Propeller Deck Planks
More informationof the Connecticut Marine Model Society, An IPMS Connecticut Chapter June 8, 2013
of the Connecticut Marine Model Society, An IPMS Connecticut Chapter The newsletter June 8, 2013 CMMS BUFFET DAY! WHAT YOU NEED TO KNOW THE meeting opened at 10 am, with Nic back at the helm. 24 members
More informationInstallation, Compensation and Maintenance Instructions for. RITCHIE Compasses. Made In U.S.A
Installation, Compensation and Maintenance Instructions for RITCHIE Compasses Made In U.S.A All Magnetic Compasses are vulnerable to magnetic interference, which will produce errors, called deviation.
More informationINSTALLING THE TRIDENT 11, 13 OR 15 RUDDER
INSTALLING THE TRIDENT 11, 13 OR 15 RUDDER Parts Included: Steering Parts: Foot Rail Parts: Rudder Parts: Retraction Parts: 4 - Rubber 2 - Rail Assemblies 1 - Rudder Body 1 - Rudder Retraction Grommets
More informationTrim Tab Wind Vane for boats with transom mounted rudders
Trim Tab Wind Vane for boats with transom mounted rudders If your boat has a transom mounted rudder, you can build this self-steering windvane for around $150, using regular wood working tools and some
More informationMeasurement Checklist for the Lido for the Championships
This paper is intended to be a guide for rapid and easy measurement of the Lido 14 to assure painless application of the rules that, in general, govern one design performance and compliance. It is not
More information