Phytodeket Test Kit. Phytodeket Test Kit (all PDK catalog numbers) contains the following components:

Transcription

1 Phytodeket Test Kit DRAFT: 1-Dec-217 Phytodeket Test Kit (all PDK catalog numbers) contains the following components: Stick Controls and Standards Coated Plates Phytodetek tracer, liquid Component SDS Number All SPC and STD catalog numbers. All PLT catalog numbers (solid plate or strips) All PDA catalog numbers TBS buffer, 2X solution ACC 58 PNP Substrate Tablets (5mg) ACC 44 Substrate Diluent (for Phytodeket kits) PDN 21, included in all PDK Phytodeket kits PBST Buffer, 2X ACC 51 SDS documents for each component listed above are included in this document. Page 1 of 16

2 This page intentionally left blank. Page 2 of 16

3 Stick Controls and Standards 1 PRODUCT AND COMPANY IDENTIFICATION Product Name: Stick Controls and Standards Catalog #: All SPC and STD catalog numbers. Product Use: Controls or Standards. Manufacturer: Agdia, Inc County Road 1 Elkhart, IN (574) Contact: Fax: Web: Emergency: Contact physician or poison control hotline. 2 HAZARDS IDENTIFICATION Revision Date: 1-Dec-217 Safety Program Facilitator (574) info@agdia.com GHS Classification: GHS Pictograms: Not Hazardous Health 1 Fire Precautions: If exposed or concerned, seek medical advice or attention. GHS Hazards: None identified. Keep away from open flames. HMIS Reactivity 3 COMPOSITION / INFORMATION ON INGREDIENTS Composition / Formula: Proprietary formulation. No reportable quantities of hazardous chemicals. Strip impreganated with dry protein and/or chemical components. 4 FIRST AID MEASURES Inhalation: Move to fresh air. If breathing is difficult, provide oxygen. Seek medical attention if needed. Skin Contact: If skin irritation occurs, wash with soap and water. Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Ingestion: Rinse mouth with water. Consult a physician if needed. 5 FIRE FIGHTING MEASURES Fire Fighting: Avoid contact with open flames. Use any extinquishing agent if needed. Specific Fire Hazards: May ignite if exposed to flame or spark. 6 ACCIDENTAL RELEASE MEASURES Accidental Release: Wear suitable laboratory protective clothing. Pick up excess with inert absorbant material and place into separate waste container. Flush area with warm soapy water. 7 HANDLING AND STORAGE Handling Precautions: Use standard laboratory safety practices. Avoid open flames. Protective gear shown in Section 8. Storage Requirements: Store under refrigeration (+2 to +8 C). Page 3 of 16

4 Stick Controls and Standards 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Controls: Use mechanical (general) ventilation for storage areas. Revision Date: 1-Dec-217 Protective Equipment: No special protective equipment required. Handle in accordance with good industrial hygiene and safety practices. If substance is a powder, nuisance exposures may be avoided with use of type P95 (US) or type P1 (EU EN 143) particle respirator. Exposure Guidelines: PEL - None Established. TLV - None Established. 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: Test strip Physical State: Solid Solubility: Soluble components released upon water exposure. Flash Point: Not available. AutoIgnition: Not available. Other Information: Dry reagents impreganted on test strip format. No additional physical or chemical information available. 1 STABILITY AND REACTIVITY Reactivity Hazards: None known. Conditions To Avoid: None known. Stability: Stable under normal conditions. Materials To Avoid: Strong oxidizing agents. Hazardous By-products: No hazarous reactions nor hazardous decomposition products known. 11 TOXICOLOGICAL INFORMATION Toxicology Information: The complete chemical, physical, and toxicological properties of this material have not been thoroughly investigated to the best of Agdia s knowledge. 12 ECOLOGICAL INFORMATION Ecological Information: No data available 13 DISPOSAL CONSIDERATIONS Disposal: Dispose of in accordance with local regulations. 14 TRANSPORT INFORMATION Transport Information: Not dangerous goods per DOT, IATA, and IMDG. 15 REGULATORY INFORMATION Regulatory Information: CERCLA: Not Applicable. SARA Title III: Not Listed 16 OTHER INFORMATION Odor: None ph: N/A Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained herein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). This information only describes safety measures and no liability may arise from the use or application of the product described herein. This information is given in good faith and based on our current knowledge of the product. For R&D use only. Not for drug, household or other uses. Page 4 of 16

5 Coated Plates Revision Date: 1-Dec PRODUCT AND COMPANY IDENTIFICATION Product Name: Coated Plates Catalog #: All PLT catalog numbers (solid plate or strips) Product Use: ELISA test component Manufacturer: Agdia, Inc County Road 1 Elkhart, IN (574) Contact: Fax: Web: Emergency: Contact physician or poison control hotline. 2 HAZARDS IDENTIFICATION Safety Program Facilitator (574) info@agdia.com GHS Classification: GHS Pictograms: Not Hazardous Health Fire Precautions: If exposed or concerned, seek medical advice or attention. GHS Hazards: None identified. HMIS Reactivity 3 COMPOSITION / INFORMATION ON INGREDIENTS Composition / Formula: Antibodies bound to plastic microtiter plate. No hazardous components or carcinogens >.1%. 4 FIRST AID MEASURES Inhalation: Move to fresh air. If breathing is difficult, provide oxygen. Seek medical attention if needed. Skin Contact: If skin irritation occurs, wash with soap and water. Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Ingestion: Rinse mouth with water. Consult a physician if needed. 5 FIRE FIGHTING MEASURES Fire Fighting: Not expected to ignite. If involved in a fire, use appropriate extinquishing agent for surrounding fire. Specific Fire Hazards: None known. 6 ACCIDENTAL RELEASE MEASURES Accidental Release: Wear suitable laboratory protective clothing. Pick up excess with inert absorbant material and place into separate waste container. Flush area with warm soapy water. 7 HANDLING AND STORAGE Handling Precautions: Use standard laboratory safety practices. Protective gear shown in Section 8. Storage Requirements: Store under refrigeration (+2 to +8 C). Page 5 of 16

6 Coated Plates Revision Date: 1-Dec EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Controls: Use mechanical (general) ventilation for storage areas. Protective Equipment: No special protective equipment required. Handle in accordance with good industrial hygiene and safety practices. If substance is a powder, nuisance exposures may be avoided with use of type P95 (US) or type P1 (EU EN 143) particle respirator. Exposure Guidelines: PEL - None Established. TLV - None Established. 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: Clear plastic plate Physical State: Solid Solubility: N/A Other Information: No additional physical or chemical information available. 1 STABILITY AND REACTIVITY Flash Point: Not available. AutoIgnition: Not available. Reactivity Hazards: None known. Conditions To Avoid: None known. Stability: Stable under normal conditions. Materials To Avoid: Strong oxidizing agents. Hazardous By-products: No hazarous reactions nor hazardous decomposition products known. 11 TOXICOLOGICAL INFORMATION Toxicology Information: The complete chemical, physical, and toxicological properties of this material have not been thoroughly investigated to the best of Agdia s knowledge. 12 ECOLOGICAL INFORMATION Ecological Information: No data available 13 DISPOSAL CONSIDERATIONS Disposal: Dispose of in accordance with local regulations. 14 TRANSPORT INFORMATION Transport Information: Not dangerous goods per DOT, IATA, and IMDG. 15 REGULATORY INFORMATION Regulatory Information: CERCLA: Not Applicable. SARA Title III: Not Listed 16 OTHER INFORMATION Odor: None ph: N/A Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained herein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). This information only describes safety measures and no liability may arise from the use or application of the product described herein. This information is given in good faith and based on our current knowledge of the product. For R&D use only. Not for drug, household or other uses. Page 6 of 16

7 Phytodetek tracer, liquid Revision Date: 1-Dec PRODUCT AND COMPANY IDENTIFICATION Product Name: Phytodetek tracer, liquid Catalog #: All PDA catalog numbers Product Use: Substrate Manufacturer: Agdia, Inc County Road 1 Elkhart, IN (574) Contact: Fax: Web: Emergency: Contact physician or poison control hotline. 2 HAZARDS IDENTIFICATION Safety Program Facilitator (574) info@agdia.com GHS Classification: GHS Pictograms: Not Hazardous Health Fire Precautions: If exposed or concerned, seek medical advice or attention. GHS Hazards: None identified. HMIS Reactivity 3 COMPOSITION / INFORMATION ON INGREDIENTS Composition / Formula: Proprietary formulation; no hazardous components or carcinogens >.1%. 4 FIRST AID MEASURES Inhalation: Move to fresh air. If breathing is difficult, provide oxygen. Seek medical attention if needed. Skin Contact: If skin irritation occurs, wash with soap and water. Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Ingestion: Rinse mouth with water. Consult a physician if needed. 5 FIRE FIGHTING MEASURES Fire Fighting: Not expected to ignite. If involved in a fire, use appropriate extinquishing agent for surrounding fire. Specific Fire Hazards: None known. 6 ACCIDENTAL RELEASE MEASURES Accidental Release: Wear suitable laboratory protective clothing. Pick up excess with inert absorbant material and place into separate waste container. Flush area with warm soapy water. 7 HANDLING AND STORAGE Handling Precautions: Use standard laboratory safety practices. Protective gear shown in Section 8. Storage Requirements: Store under refrigeration (+2 to +8 C). 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Page 7 of 16

8 Phytodetek tracer, liquid Revision Date: 1-Dec-217 Engineering Controls: Use mechanical (general) ventilation for storage areas. Protective Equipment: No special protective equipment required. Handle in accordance with good industrial hygiene and safety practices. If substance is a powder, nuisance exposures may be avoided with use of type P95 (US) or type P1 (EU EN 143) particle respirator. Exposure Guidelines: PEL - None Established. TLV - None Established. 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: Clear solution Physical State: Liquid Solubility: Completely soluble in water Other Information: No additional physical or chemical information available. 1 STABILITY AND REACTIVITY Flash Point: Not available. AutoIgnition: Not available. Reactivity Hazards: None known. Conditions To Avoid: None known. Stability: Stable under normal conditions. Materials To Avoid: Strong oxidizing agents. Hazardous By-products: No hazarous reactions nor hazardous decomposition products known. 11 TOXICOLOGICAL INFORMATION Toxicology Information: The complete chemical, physical, and toxicological properties of this material have not been thoroughly investigated to the best of Agdia s knowledge. 12 ECOLOGICAL INFORMATION Ecological Information: No data available 13 DISPOSAL CONSIDERATIONS Disposal: Dispose of in accordance with local regulations. 14 TRANSPORT INFORMATION Transport Information: Not dangerous goods per DOT, IATA, and IMDG. 15 REGULATORY INFORMATION Regulatory Information: CERCLA: Not Applicable. SARA Title III: Not Listed 16 OTHER INFORMATION Odor: None ph: N/A Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained herein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). This information only describes safety measures and no liability may arise from the use or application of the product described herein. This information is given in good faith and based on our current knowledge of the product. For R&D use only. Not for drug, household or other uses. Page 8 of 16

9 TBS buffer, 2X solution Revision Date: 1-Dec PRODUCT AND COMPANY IDENTIFICATION Product Name: TBS buffer, 2X solution Catalog #: ACC 58 Product Use: Buffer Manufacturer: Agdia, Inc County Road 1 Elkhart, IN (574) Contact: Fax: Web: Emergency: Contact physician or poison control hotline. 2 HAZARDS IDENTIFICATION Safety Program Facilitator (574) info@agdia.com GHS Classification: GHS Pictograms: Warning Health 2 Fire Precautions: If exposed or concerned, seek medical advice or attention. GHS Hazards: MAY CAUSE SERIOUS EYE IRRITATION/ DAMAGE (2A). HMIS Reactivity 3 COMPOSITION / INFORMATION ON INGREDIENTS Composition / Formula: Tris Base (CAS# 77861), 1.1%; Tris HCl (CAS # ), 6.5%; Sodium Chloride (CAS# ), 11.7%; and Magnesium Chloride, hexahydrate (CAS# ),.4%; in water. 4 FIRST AID MEASURES Inhalation: Move to fresh air. If breathing is difficult, provide oxygen. Seek medical attention if needed. Skin Contact: If skin irritation occurs, wash with soap and water. Eye Contact: MAY CAUSE SERIOUS EYE IRRITATION/ DAMAGE (2A). Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Seek medical help. Ingestion: Rinse mouth with water. Consult a physician if needed. 5 FIRE FIGHTING MEASURES Fire Fighting: Not expected to ignite. If involved in a fire, use appropriate extinquishing agent for surrounding fire. Specific Fire Hazards: Emits toxic fumes under fire conditions. 6 ACCIDENTAL RELEASE MEASURES Accidental Release: Wear suitable laboratory protective clothing. Pick up excess with inert absorbant material and place into separate waste container. Flush area with warm soapy water. 7 HANDLING AND STORAGE Handling Precautions: Use standard laboratory safety practices. Protective gear shown in Section 8. Page 9 of 16

10 TBS buffer, 2X solution Revision Date: 1-Dec-217 Storage Requirements: Store under refrigeration (+2 to +8 C). 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Controls: Use mechanical (general) ventilation for storage areas. Protective Equipment: Handle in accordance with good industrial hygiene and safety practices. Eye protection and gloves recommended. If substance is a powder, nuisance exposures may be avoided with use of type P95 (US) or type P1 (EU EN 143) particle respirator. Exposure Guidelines: PEL - None Established. TLV - None Established. 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: Clear Liquid Physical State: Liquid Solubility: Completely soluble in water Other Information: No additional physical or chemical information available. 1 STABILITY AND REACTIVITY Flash Point: Not available. AutoIgnition: Not available. Reactivity Hazards: None known. Conditions To Avoid: None known. Stability: Stable under normal conditions. Materials To Avoid: Strong oxidizing agents. Hazardous By-products: Hazardous decomposition products: Sodium oxides, hydrogen chloride gas, carbon oxides, nitrous vitriol gases. No hazarous reactions known. 11 TOXICOLOGICAL INFORMATION Toxicology Information: The complete chemical, physical, and toxicological properties of this material have not been thoroughly investigated to the best of Agdia s knowledge. 12 ECOLOGICAL INFORMATION Ecological Information: No data available 13 DISPOSAL CONSIDERATIONS Disposal: Dispose of in accordance with local regulations. 14 TRANSPORT INFORMATION Transport Information: Not dangerous goods per DOT, IATA, and IMDG. 15 REGULATORY INFORMATION Regulatory Information: CERCLA: Not Applicable. SARA Title III: Not Listed. 16 OTHER INFORMATION Odor: None ph: ~ 7.5 Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained herein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). This information only describes safety measures and no liability may arise from the use or application of the product described herein. This information is given in good faith and based on our current knowledge of the product. For R&D use only. Not for drug, household or other uses. Page 1 of 16

11 PNP Substrate Tablets (5mg) 1 PRODUCT AND COMPANY IDENTIFICATION Product Name: PNP Substrate Tablets (5mg) Catalog #: ACC 44 Product Use: Substrate Manufacturer: Agdia, Inc County Road 1 Elkhart, IN (574) Contact: Fax: Web: Emergency: Contact physician or poison control hotline. 2 HAZARDS IDENTIFICATION Revision Date: 1-Dec-217 Safety Program Facilitator (574) info@agdia.com GHS Classification: GHS Pictograms: Not Hazardous Health Fire Precautions: If exposed or concerned, seek medical advice or attention. GHS Hazards: None identified. 3 COMPOSITION / INFORMATION ON INGREDIENTS Composition / Formula: p-nitrophenyl phosphate (CAS ) HMIS Reactivity 4 FIRST AID MEASURES Inhalation: Move to fresh air. If breathing is difficult, provide oxygen. Seek medical attention if needed. Skin Contact: If skin irritation occurs, wash with soap and water. Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Ingestion: Rinse mouth with water. Consult a physician if needed. 5 FIRE FIGHTING MEASURES Fire Fighting: Not expected to ignite. If involved in a fire, use appropriate extinquishing agent for surrounding fire. Specific Fire Hazards: Carbon oxides, Nitrogen oxides (NOx), Oxides of phosphorus, Sodium oxides. 6 ACCIDENTAL RELEASE MEASURES Accidental Release: Wear suitable laboratory protective clothing. Pick up excess with inert absorbant material and place into separate waste container. Flush area with warm soapy water. 7 HANDLING AND STORAGE Handling Precautions: Use standard laboratory safety practices. Protective gear shown in Section 8. Storage Requirements: Store under refrigeration (+2 to +8 C). 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Page 11 of 16

12 PNP Substrate Tablets (5mg) Engineering Controls: Use mechanical (general) ventilation for storage areas. Revision Date: 1-Dec-217 Protective Equipment: No special protective equipment required. Handle in accordance with good industrial hygiene and safety practices. If substance is a powder, nuisance exposures may be avoided with use of type P95 (US) or type P1 (EU EN 143) particle respirator. Exposure Guidelines: PEL - None Established. TLV - None Established. 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: White to Yellow Tablet Physical State: Solid Solubility: Completely soluble in water Flash Point: Not available. AutoIgnition: Not available. Other Information: Melting point/freezing point: > 3 C (> 572 F). No additional physical or chemical information available. 1 STABILITY AND REACTIVITY Reactivity Hazards: None known. Conditions To Avoid: None known. Stability: Stable under normal conditions. Materials To Avoid: Strong oxidizing agents, Strong acids, Strong bases Hazardous By-products: No hazarous reactions nor hazardous decomposition products known. 11 TOXICOLOGICAL INFORMATION Toxicology Information: The complete chemical, physical, and toxicological properties of this material have not been thoroughly investigated to the best of Agdia s knowledge. 12 ECOLOGICAL INFORMATION Ecological Information: No data available 13 DISPOSAL CONSIDERATIONS Disposal: Dispose of in accordance with local regulations. 14 TRANSPORT INFORMATION Transport Information: Not dangerous goods per DOT, IATA, and IMDG. 15 REGULATORY INFORMATION Regulatory Information: CERCLA: Not Applicable. SARA Title III: Not Listed 16 OTHER INFORMATION Odor: None ph: N/A Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained herein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). This information only describes safety measures and no liability may arise from the use or application of the product described herein. This information is given in good faith and based on our current knowledge of the product. For R&D use only. Not for drug, household or other uses. Page 12 of 16

13 Substrate Diluent (for Phytodeket kits) 1 PRODUCT AND COMPANY IDENTIFICATION Product Name: Substrate Diluent (for Phytodeket kits) Catalog #: PDN 21, included in all PDK Phytodeket kits Product Use: Diluent Manufacturer: Agdia, Inc County Road 1 Elkhart, IN (574) Contact: Fax: Web: Emergency: Contact physician or poison control hotline. 2 HAZARDS IDENTIFICATION Revision Date: 1-Dec-217 Safety Program Facilitator (574) info@agdia.com GHS Classification: GHS Pictograms: DANGER Health 2 Fire Precautions: If exposed or concerned, seek medical advice or attention. GHS Hazards: Harmful if swallowed. Causes respiratory tract irriation. Causes skin irritation. May cause serious eye damage. Suspected of causing cancer. May cause organ damage with prolonged or repeated exposure. 3 COMPOSITION / INFORMATION ON INGREDIENTS Composition / Formula: Proprietary formulation containing diethanolamine (CAS , <15%). No other hazardous components or carcinogens >.1%. 4 FIRST AID MEASURES Inhalation: Move to fresh air. If breathing is difficult, provide oxygen. Seek medical attention if needed. Skin Contact: If skin irritation occurs, wash with soap and water. Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Ingestion: Rinse mouth with water. Consult a physician if needed. 5 FIRE FIGHTING MEASURES Fire Fighting: Not expected to ignite. If involved in a fire, use appropriate extinquishing agent for surrounding fire. Specific Fire Hazards: None known. 6 ACCIDENTAL RELEASE MEASURES Accidental Release: Wear suitable laboratory protective clothing. Pick up excess with inert absorbant material and place into separate waste container. Flush area with warm soapy water. 7 HANDLING AND STORAGE Handling Precautions: Use standard laboratory safety practices. Protective gear shown in Section 8. Page 13 of 16 HMIS Reactivity

14 Substrate Diluent (for Phytodeket kits) Storage Requirements: Store under refrigeration (+2 to +8 C). 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Controls: Use mechanical (general) ventilation for storage areas. Revision Date: 1-Dec-217 Protective Equipment: Handle in accordance with good industrial hygiene and safety practices. Eye protection and gloves recommended. If substance is a powder, nuisance exposures may be avoided with use of type P95 (US) or type P1 (EU EN 143) particle respirator. Exposure Guidelines: PEL - None Established. TLV - None Established. 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: Clear yellow liquid Physical State: Liquid Solubility: Completely soluble in water Other Information: No additional physical or chemical information available. 1 STABILITY AND REACTIVITY Flash Point: Not available. AutoIgnition: Not available. Reactivity Hazards: None known. Conditions To Avoid: None known. Stability: Stable under normal conditions. Materials To Avoid: Strong oxidizing agents. Hazardous By-products: No hazarous reactions nor hazardous decomposition products known. 11 TOXICOLOGICAL INFORMATION Toxicology Information: The complete chemical, physical, and toxicological properties of this material have not been thoroughly investigated to the best of Agdia s knowledge. 12 ECOLOGICAL INFORMATION Ecological Information: No data available 13 DISPOSAL CONSIDERATIONS Disposal: Dispose of in accordance with local regulations. 14 TRANSPORT INFORMATION Transport Information: Not dangerous goods per DOT, IATA, and IMDG. 15 REGULATORY INFORMATION Regulatory Information: CERCLA: Not Applicable. SARA Title III: Not Listed 16 OTHER INFORMATION Odor: None ph: ~ 9.8 Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained herein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). This information only describes safety measures and no liability may arise from the use or application of the product described herein. This information is given in good faith and based on our current knowledge of the product. For R&D use only. Not for drug, household or other uses. Page 14 of 16

15 PBST Buffer, 2X Revision Date: 1-Dec PRODUCT AND COMPANY IDENTIFICATION Product Name: PBST Buffer, 2X Catalog #: ACC 51 Product Use: Buffer Manufacturer: Agdia, Inc County Road 1 Elkhart, IN (574) Contact: Fax: Web: Emergency: Contact physician or poison control hotline. 2 HAZARDS IDENTIFICATION Safety Program Facilitator (574) info@agdia.com GHS Classification: GHS Pictograms: Not Hazardous Health Fire Precautions: If exposed or concerned, seek medical advice or attention. GHS Hazards: None identified. HMIS Reactivity 3 COMPOSITION / INFORMATION ON INGREDIENTS Composition / Formula: Potassium Phosphate, monobasic (CAS ), Sodium Phosphate, dibasic (CAS ), Potassium Chloride (CAS ), Sodium Chloride (CAS ), and Tween 2 (CAS ) in water. 4 FIRST AID MEASURES Inhalation: Move to fresh air. If breathing is difficult, provide oxygen. Seek medical attention if needed. Skin Contact: If skin irritation occurs, wash with soap and water. Eye Contact: CAUSES SERIOUS EYE IRRITATION/ DAMAGE (2A). Immediately flush eyes with large amounts of water for at least 15 minutes, lifting eyelids occasionally to facilitate irrigation. Seek medical help. Ingestion: Rinse mouth with water. Consult a physician if needed. 5 FIRE FIGHTING MEASURES Fire Fighting: Not expected to ignite. If involved in a fire, use appropriate extinquishing agent for surrounding fire. Specific Fire Hazards: Decomposes on heating emitting oxides of carbon. 6 ACCIDENTAL RELEASE MEASURES Accidental Release: Wear suitable laboratory protective clothing. Pick up excess with inert absorbant material and place into separate waste container. Flush area with warm soapy water. 7 HANDLING AND STORAGE Handling Precautions: Use standard laboratory safety practices. Protective gear shown in Section 8. Page 15 of 16

16 PBST Buffer, 2X Revision Date: 1-Dec-217 Storage Requirements: Store at room temperature in a well ventilated area. 8 EXPOSURE CONTROLS / PERSONAL PROTECTION Engineering Controls: Use mechanical (general) ventilation for storage areas. Protective Equipment: Handle in accordance with good industrial hygiene and safety practices. Eye protection and gloves recommended. If substance is a powder, nuisance exposures may be avoided with use of type P95 (US) or type P1 (EU EN 143) particle respirator. Exposure Guidelines: PEL - None Established. TLV - None Established. 9 PHYSICAL AND CHEMICAL PROPERTIES Appearance: Colorless liquid Physical State: Liquid Solubility: Completely soluble in water Other Information: No additional physical or chemical information available. 1 STABILITY AND REACTIVITY Flash Point: Not available. AutoIgnition: Not available. Reactivity Hazards: None known. Conditions To Avoid: Heat, flames. Stability: Stable under normal conditions. Materials To Avoid: Strong oxidizing agents, alkalis, and acids. Hazardous By-products: Emits smoke and fumes when heated to decomposition. No hazardous reactions known. 11 TOXICOLOGICAL INFORMATION Toxicology Information: The complete chemical, physical, and toxicological properties of this material have not been thoroughly investigated to the best of Agdia s knowledge. 12 ECOLOGICAL INFORMATION Ecological Information: No data available 13 DISPOSAL CONSIDERATIONS Disposal: Dispose of in accordance with local regulations. 14 TRANSPORT INFORMATION Transport Information: Not dangerous goods per DOT, IATA, and IMDG. 15 REGULATORY INFORMATION Regulatory Information: CERCLA: Not Applicable. SARA Title III: Not Listed. 16 OTHER INFORMATION Odor: None ph: ~ 7.1 Disclaimer: Although reasonable care has been taken in the preparation of this document, we extend no warranties and make no representations as to the accuracy or completeness of the information contained herein, and assume no responsibility regarding the suitability of this information for the user's intended purposes or for the consequences of its use. Each individual should make a determination as to the suitability of the information for their particular purpose(s). This information only describes safety measures and no liability may arise from the use or application of the product described herein. This information is given in good faith and based on our current knowledge of the product. For R&D use only. Not for drug, household or other uses. Page 16 of 16