507 Rapid Set Cold Pothole Repair Material Safety Data Sheet

Transcription

1 507 Rapid Set Cold Pothole Repair Material Safety Data Sheet means No Data Available Identity (As Used on Label and List) Note: Blank spaces are not permitted. It any item is 507 Rapid Set Cold Pothole Repair not applicable, or no information is available, the space must be marked to indicate that. Section I Manufacturer's Name Emergency Telephone Number: Manufacturer's Address Chemtrec Telephone Number for Information: DeWitt Products Company Plumer Avenue Detroit, MI Date Prepared: January 2012 Section II - Hazardous Ingredients/Identity Information Hazardous Components (Specific Chemical Identity; CAS# %Wt. Common Name(s)) Limestone Modified Petroleum Asphalt Base Petroleum Solvent Additives Section III - Physical/Chemical Characteristics Appearance: Black, coated stone Odor: Slight petroleum odor Physical State: Granular solid ph: Boiling Point: Melting Point: Freezing Point: Vapor Pressure: Specific Gravity: Greater than water Vapor Density: (H 2 O =1) Evap. Rate: Solubility in Water: % Solids by Wt.: Section IV - Fire and Explosion Hazard Flash Point: Flammable Limits in Air: Auto Ignition Temp: NFPA Hazard Classification: Health = 1 Flammability = 1 Reactivity = 0 HMIS Hazard Classification: Health = 1 Flammability = 1 Reactivity = 0 Protection: Extinguishing Media: Special Fire Fighting Procedures: Unusual Fire and Explosion Hazards: Hazardous Decomposition Products: Safety glasses and gloves Carbon dioxide, dry chemical and water fog. Foam or water stream may cause frothing. SCBA may be necessary in enclosed areas to prevent breathing of vapors Storage at elevated temperatures may cause release of flammable vapors in ope and/or confined areas. Carbon monoxide, sulfur, and various hydrocarbons may be formed as a result of combustion. Page 1 of 5

2 Section V - Stability and Reactivity Stability: Stable Conditions to Avoid: Avoid contact with excessive heat and open flame. Incompatibility: Incompatible with acids, bases, and oxidizing flame. Hazardous Decomposition or By-Products: Carbon monoxide and various hydrocarbons Hazardous Polymerization: Condition to Avoid: Section VI - Health Hazard Data Emergency Overview Routes of Entry: Potential Health Effects Eyes: Skin: Ingestion: Inhalation: Acute Health Hazards: Chronic Health Hazards: Eyes, skin, ingestion, inhalation Severe irritation including redness, tearing, and blurred vision. Prolonged or repeated contact may cause skin irritation and/or dermatitis. Swallowing can cause irritation of the mouth, throat and stomach. Nausea, vomiting and diarrhea may result. Fumes from these materials when heated or used indoors may cause headaches nausea and dizziness. Fumes may also irritate the nose, throat and lungs. Prolonged exposure to high levels of fumes may cause unconsciousness. Product contains trace amounts of crystalline silica. Cutting or grinding hardened material will release respirable crystalline silica. Prolonged or repeated inhalation of respirable crystalline silica from this product can cause silicosis, a serious and fatal lung disease. Carcinogenicity: OSHA - not regulated ACGIH - No NTP - No IARC - No First Aid Measures: Eyes: Skin: Ingestion: Inhalation: Section VII - Precautions for Handling and Storage Handling and Storage: Other Precautions: Flush with large amounts of water for at least 15 minutes. Lift upper and lower lids to ensure all material is flushed out of eyes. Contact a physician. Immediately remove any contaminated clothing and wash affected areas with soap and water. Thoroughly was contaminated clothing before wearing. If irritation or redness develops consult a physician. Do not induce vomiting. Vomiting can cause the material to be aspirated into the lungs. Keep person warm and calm. Obtain immediate medical attention. Move individual to fresh air. If he/she is having difficulty breathing or is not conscious, obtain immediate medical attention. Store in well-ventilated area away from heat and flame. Keep sealed until use. Product should not be heated or exposed to temperatures above 100 F. Section VIII - Accidental Release Measures/Disposal Considerations Accidental Release Measure: Waste Disposal Method: RCRA Hazard Class: Section IX - Exposure Controls/Personal Protection Engineering Controls: Ventilation: Respiratory Protection: Eye Protection: Skin Protection: Recover spilled material into suitable container. Material can be reused. Dispose of used containers and material according to local, state and federal requirements. This material in its purchased form is not a hazardous waste by listing or characteristic. It is the responsibility of the product user to determine at the time of disposal whether it should be classified as hazardous waste. Under normal use engineering controls are not required. No ventilation required under normal circumstances. No respiratory protection required under normal circumstances. If material is handled in a confined area wear respirator with a NIOSH approved organic vapor respiratory cartridge. Provide sufficient ventilation to prevent vapors from accumulating and to maintain exposure levels below TLV's. Use ANSI approved safety glasses or face shield to prevent contact with eyes. Wear gloves and appropriate clothing to prevent contact with skin. Page 2 of 5

3 Other Protective Clothing or Equipment: Work Hygienic Practices: Exposure Guidelines: Wear leather shoes or boots. Wash any exposed skin immediately after handling. Thoroughly wash contaminated clothing before wearing. Ingredient PEL TLV Limestone (total dust) 15 mg/cu.m 15 mg/cu.m Modified Petroleum Asphalt Base(as fumes) 5 ppm 5ppm Petroleum Solvent Not established Not established Section X - Transportation Information Not Regulated by DOT as a hazardous substance. Proper Shipping Name: Hazard Class: None ID Number: None Packing Group: Label Statement: Page 3 of 5

4 en f Page 4 of 5

5 s, r Page 5 of 5